CABLETRON-TRAPS
AI MIB Summary
Standard SNMP MIB module defining data structures for CABLETRON-TRAPS.
446
Objects
Active
Status
33
Dependencies
Imported Objects
Objects
446 total| Object Name |
|---|
CTRON-OIDSFROM TRAP-TYPE .1.3.6.1.4.1.52.0.1 |
ctdlswTConnDownThis trap is sent each time a transport connection
becomes disabled on this DLSw. TRAP-TYPE .1.3.6.1.4.1.52.0.2 |
portSegmentingWhen a port goes from operational to segmented, a
trap will be generated. For these purposes, the
port state will be sampled every XXX seconds, thus
it will be statistically possible to miss oscillating
circuits. TRAP-TYPE .1.3.6.1.4.1.52.0.257 |
portUnsegementingWhen it is detected that a previously segmented port
has gone operational, a trap will be generated. This
is also sampled, thus a trap may not be generated for
each transition. TRAP-TYPE .1.3.6.1.4.1.52.0.258 |
portLinkUpThis trap will be generated when it is determined
that a MAU has been attached to the MMAC. This is
only appropriate for MIMs that support the concept
of a link state. TRAP-TYPE .1.3.6.1.4.1.52.0.259 |
portLinkDownThis trap will be generated when a previously attached
MAU is removed or powered down. Again, this is only
appropriate for MIM's that support link state. TRAP-TYPE .1.3.6.1.4.1.52.0.260 |
srcaddrNewThis trap will be generated when the MMAC detects
the existence of a new source address on one of it's
ports. TRAP-TYPE .1.3.6.1.4.1.52.0.261 |
srcaddrTimeoutThis trap will indicate that the MMAC has not
detected a packet generated by this source address
within a certain timeout. TRAP-TYPE .1.3.6.1.4.1.52.0.262 |
boardRemovalThis trap will be generated when the MMAC detects
that a MIM has been removed. TRAP-TYPE .1.3.6.1.4.1.52.0.263 |
boardInsertionThis trap will generated when the MMAC determines
that a new board has been inserted. TRAP-TYPE .1.3.6.1.4.1.52.0.264 |
redundActivePortInCircuitFailedThis trap will be generated when the active port in
a redundant circuit has failed polling. This will
indicate the activation of redundancy. TRAP-TYPE .1.3.6.1.4.1.52.0.265 |
redundPortActivatedThis trap indicates that a new port has been
activated in a redundant circuit. This does NOT
indicate that this port is usable, but is being
tested. If the port fails, a failure trap (above)
will be generated. TRAP-TYPE .1.3.6.1.4.1.52.0.266 |
redundPortTestFailedThis trap will be generated when the MMAC executes
it's periodic redundancy diagnostics and finds one
of the ports in a redundant circuit has failed.
This message will not indicate that redundancy has
been activated, just that the port has failed and
should be fixed before it is needed. TRAP-TYPE .1.3.6.1.4.1.52.0.267 |
boardTrafficThresholdExceededThis trap will be generated when the traffic (good
packets per time interval) has been exceeded for a
particular MIM. TRAP-TYPE .1.3.6.1.4.1.52.0.271 |
boardErrorThresholdExceededThis trap will be generated when packets of the
selected error type exceeds a threshold percentage of
the good packets for a particular interval for a
particular MIM. TRAP-TYPE .1.3.6.1.4.1.52.0.272 |
boardCollsionThresholdExceededThis trap will be generated when collisions exceed a
threshold percentage of the good packets for a particular
interval for a particular MIM. TRAP-TYPE .1.3.6.1.4.1.52.0.273 |
portTrafficThresholdExceededThis trap will be generated when the traffic (good
packets per time interval) has been exceeded for a
particular port. TRAP-TYPE .1.3.6.1.4.1.52.0.274 |
portErrorThresholdExceededThis trap will be generated when packets of the
selected error type exceeds a threshold percentage of
the good packets for a particular interval for a
particular port. TRAP-TYPE .1.3.6.1.4.1.52.0.275 |
portCollsionThresholdExceededThis trap will be generated when collisions exceed a
threshold percentage of the good packets for a particular
interval for a particular port. TRAP-TYPE .1.3.6.1.4.1.52.0.276 |
portTypeChangedThis trap indicates that a port has changed from a
station port to a trunk port or vice versa. TRAP-TYPE .1.3.6.1.4.1.52.0.277 |
portSecurityViolationThis trap is generated when a source address other
than those locked to a port is seen. TRAP-TYPE .1.3.6.1.4.1.52.0.279 |
portViolationResetThis trap is generated when management intervention
has reset a port after a violation has occurred. TRAP-TYPE .1.3.6.1.4.1.52.0.280 |
envTempWarmThis trap is generated when the device detects that
the temperature within a MIM has reached a WARM
condition. TRAP-TYPE .1.3.6.1.4.1.52.0.281 |
envTempHotThis trap is generated when the device detects that
the temperature within a MIM has reached a HOT
condition. TRAP-TYPE .1.3.6.1.4.1.52.0.282 |
envVoltageLowThis trap is generated when a power supply's voltage
is LOW. TRAP-TYPE .1.3.6.1.4.1.52.0.283 |
envTempNormalThis trap is generated when the device detects that
the temperature within a MIM has returned to a
NORMAL state. TRAP-TYPE .1.3.6.1.4.1.52.0.284 |
envVoltageNormalThis trap is generated when all power supplies' voltage
have returned to a NORMAL state. TRAP-TYPE .1.3.6.1.4.1.52.0.285 |
fanFailThis trap is generated when the device detects that
the system fans have failed. TRAP-TYPE .1.3.6.1.4.1.52.0.286 |
fanNormalThis trap is generated when the device detects that
the system fans have returned to normal. TRAP-TYPE .1.3.6.1.4.1.52.0.287 |
boardBroadcastThresholdExceededThis trap is generated when the broadcast packets
(per time interval) have exceeded the threshold for
the given board. TRAP-TYPE .1.3.6.1.4.1.52.0.289 |
portBroadcastThresholdExceededThis trap is generated when the broadcast packets
(per time interval) have exceeded the threshold for
the given port. TRAP-TYPE .1.3.6.1.4.1.52.0.290 |
systemVoltageLowThis trap is generated when the device detects that
the power to the EMME is low. TRAP-TYPE .1.3.6.1.4.1.52.0.293 |
systemVoltageNormalThis trap is generated when the device detects that
the power to the EMME has returned to normal. TRAP-TYPE .1.3.6.1.4.1.52.0.294 |
epimRemovalThis trap is generated when it is detected that an
EPIM has been removed. TRAP-TYPE .1.3.6.1.4.1.52.0.295 |
epimInsertionThis trap is generated when it is detected that an
EPIM has been inserted. TRAP-TYPE .1.3.6.1.4.1.52.0.296 |
rptrTrafficThresholdExceededThis trap will be generated when the traffic (good
packets per time interval) has been exceeded for a
network. TRAP-TYPE .1.3.6.1.4.1.52.0.297 |
fanMisconfiguredThis trap is generated when the device detects that
the system fans are misconfigured. TRAP-TYPE .1.3.6.1.4.1.52.0.298 |
rptrErrorThresholdExceededThis trap will be generated when packets of the
selected error type exceeds a threshold percentage of
the good packets for a particular interval for an
entire network. TRAP-TYPE .1.3.6.1.4.1.52.0.304 |
rptrCollsionThresholdExceededThis trap will be generated when collisions exceed a
threshold percentage of the good packets for a particular
interval for an entire network. TRAP-TYPE .1.3.6.1.4.1.52.0.305 |
rptrLockStatusChangedThis trap is generated when the status of the address
lock changes for a certain network. TRAP-TYPE .1.3.6.1.4.1.52.0.306 |
rptrBroadcastThresholdExceededThis trap is generated when the broadcast packets
(per time interval) have exceeded the threshold for
the given repeater. TRAP-TYPE .1.3.6.1.4.1.52.0.307 |
srcAddressPortLockStatusChangeThis trap is generated when a change to the
source address locking is detected at the port level. TRAP-TYPE .1.3.6.1.4.1.52.0.309 |
chBoardInsertionThis trap will generated when the MMAC determines
that a new board has been inserted. TRAP-TYPE .1.3.6.1.4.1.52.0.310 |
portSecureStateChangedThis trap is generated when the status of the secure state
changes for a specific port. TRAP-TYPE .1.3.6.1.4.1.52.0.313 |
rptrLearnStateChangedThis trap is generated when network learning is reset.
When learning is reset, all secure addresses on each
port, within the network, will be deleted and ports will
learn source addresses, again. TRAP-TYPE .1.3.6.1.4.1.52.0.314 |
rptrPortGrpLearnStateChangedThis trap is generated when port group learning is reset.
When learning is reset, all secure addresses on each port,
within the port group, will be deleted and ports will learn
source addresses, again. TRAP-TYPE .1.3.6.1.4.1.52.0.315 |
rptrPortLearnStateChangedThis trap is generated when learning on a port is reset.
When learning is reset, all secure addresses on the port
will be deleted and the port will learn source addresses,
again. TRAP-TYPE .1.3.6.1.4.1.52.0.316 |
rptrLearnModeChangedThis trap is generated when network learn mode is
changed between one-time learn mode and continuous
learn mode. TRAP-TYPE .1.3.6.1.4.1.52.0.317 |
portGrpLearnModeChangedThis trap is generated when the port group learn
mode is changed between one-time learn mode and
continuous learn mode. TRAP-TYPE .1.3.6.1.4.1.52.0.318 |
portLearnModeChangedThis trap is generated when the port learn
mode is changed between one-time learn mode and
continuous learn mode. TRAP-TYPE .1.3.6.1.4.1.52.0.319 |
fpportActivatedThis trap is generated when a port is activated in
redundancy due to another port failing. TRAP-TYPE .1.3.6.1.4.1.52.0.400 |
interfacePortInsertionThis trap will be generated when it is detected that an
interface port has been inserted. TRAP-TYPE .1.3.6.1.4.1.52.0.416 |
interfacePortRemovalThis trap will be generated when it is detected that an
interface port has been removed. TRAP-TYPE .1.3.6.1.4.1.52.0.417 |
interfacePortLinkUpThis trap will be generated when it is determined that
a port on a strictly bridging interface (not a 'repeater')
has been connected to a LAN. This is only appropriate
for ports that support the concept of a link state. TRAP-TYPE .1.3.6.1.4.1.52.0.418 |
interfacePortLinkDownThis trap will be generated when a previously attached
bridging port has been disconnected from a LAN. This is
only appropriate for ports that support the concept of a
link state. TRAP-TYPE .1.3.6.1.4.1.52.0.419 |
portInsertedThis trap is sent when a stations port's link state
turns on while the management state of the port is
Enabled. TRAP-TYPE .1.3.6.1.4.1.52.0.513 |
portDeInsertedThis trap is sent when a stations port's link state
turns off while the management state of the port is
Enabled. TRAP-TYPE .1.3.6.1.4.1.52.0.514 |
ringSpeedFaultThis trap is sent when a board enters the ring speed
fault state due to a station or ring port attaching
to the board as a different speed than the board is
configured for. TRAP-TYPE .1.3.6.1.4.1.52.0.515 |
ringSpeedFaultClearedThis trap is sent when a board leaves the ring
speed fault state. TRAP-TYPE .1.3.6.1.4.1.52.0.516 |
ringPortFaultedThis trap is sent when a ring port wraps when its
management state is Active, without regard for the
selected type of the ring port. TRAP-TYPE .1.3.6.1.4.1.52.0.517 |
ringPortFaultClearedThis trap is sent when a ring port unwraps when its
management state is Active, without regard for the
selected type of the ring port. TRAP-TYPE .1.3.6.1.4.1.52.0.518 |
beaconStateThis trap occurs when a Beacon is detected on the
ring while the ring is in the Operational state, or
when the Beacon contains different information than
the last Beacon received. TRAP-TYPE .1.3.6.1.4.1.52.0.519 |
beaconStateClearedThis trap occurs when a ring returns to the
Operational state. TRAP-TYPE .1.3.6.1.4.1.52.0.520 |
stationAddedThis trap is sent when a new station address is
added to the security allowed list TRAP-TYPE .1.3.6.1.4.1.52.0.521 |
stationRemovedThis trap is sent when a station is rejected
from the ring with a REMOVE MAC command sent
by the ring security. TRAP-TYPE .1.3.6.1.4.1.52.0.522 |
ringConfigurationChangedThis trap is sent when the TRMM has built a
new station map. TRAP-TYPE .1.3.6.1.4.1.52.0.523 |
faultRecoveryPortRemovedThis trap is sent after a fault recovery condition
has been corrected, and reports that a port was
removed in the process of correcting the condition. TRAP-TYPE .1.3.6.1.4.1.52.0.524 |
faultRecoveryBoardBypassedThis trap is sent after a fault recovery condition
has been corrected, and reports that a board was
bypassed in the process of correcting the condition. TRAP-TYPE .1.3.6.1.4.1.52.0.525 |
portViolationThis trap is sent when a port link state turns on
and the port's management state is Disabled. TRAP-TYPE .1.3.6.1.4.1.52.0.526 |
portViolationClearedThis trap is sent when a port link state turns off
and the port's management state is Disabled. TRAP-TYPE .1.3.6.1.4.1.52.0.527 |
faultRecoveryOscillationThis trap is sent when the ring has oscillated several
times within a short amount of time. The ring is
considered oscillating if it has failed a short time
after recovering. TRAP-TYPE .1.3.6.1.4.1.52.0.528 |
ringPurgeThresholdThis trap is sent when ring purge errors have exceeded
the specified threshold value. TRAP-TYPE .1.3.6.1.4.1.52.0.529 |
amErrorsThresholdThis trap is sent when Active Monitor errors have exceeded
the specified threshold value. TRAP-TYPE .1.3.6.1.4.1.52.0.530 |
tokenErrorsThresholdThis trap is sent when Token errors have exceeded
the specified threshold value. TRAP-TYPE .1.3.6.1.4.1.52.0.531 |
claimTokenThresholdThis trap is sent when claim tokens have exceeded
the specified threshold value. TRAP-TYPE .1.3.6.1.4.1.52.0.532 |
lostFramesThresholdThis trap is sent when the Lost Frame count has exceeded
the specified threshold value. TRAP-TYPE .1.3.6.1.4.1.52.0.533 |
beaconStateThresholdThis trap is sent when the Beacon State count has exceeded
the specified threshold value. TRAP-TYPE .1.3.6.1.4.1.52.0.534 |
frameCountThresholdThis trap is sent when the frame count has exceeded
the specified threshold value. TRAP-TYPE .1.3.6.1.4.1.52.0.535 |
lineErrorsThresholdThis trap is sent when the line errors have exceeded
the specified threshold value for the station. TRAP-TYPE .1.3.6.1.4.1.52.0.536 |
internalErrorsThresholdThis trap is sent when the Lost internal errors have exceeded
the specified threshold value for the station. TRAP-TYPE .1.3.6.1.4.1.52.0.537 |
burstErrorsThresholdThis trap is sent when the Lost burst errors have exceeded
the specified threshold value for the station. TRAP-TYPE .1.3.6.1.4.1.52.0.538 |
acErrorsThresholdThis trap is sent when address/copied errors have exceeded
the specified threshold value for the station. TRAP-TYPE .1.3.6.1.4.1.52.0.539 |
receiverCongestionThresholdThis trap is sent when receiver congestion errors have exceeded
the specified threshold value for the station. TRAP-TYPE .1.3.6.1.4.1.52.0.540 |
removeStationFailureThis trap is sent when a station breaks through security
and cannot be removed from the ring. TRAP-TYPE .1.3.6.1.4.1.52.0.541 |
ringSpeedPortFaultThis trap is generated when a port enters the ring speed
fault state due to a station or ring port attaching to the
port at a different speed than the port is configured for. TRAP-TYPE .1.3.6.1.4.1.52.0.542 |
ringSpeedPortFaultClearedThis trap is generated when a port leaves the ring speed
fault state. TRAP-TYPE .1.3.6.1.4.1.52.0.543 |
stnPortInsertedThis trap is sent when a stations port's link state
turns on while the management state of the port is
Enabled. TRAP-TYPE .1.3.6.1.4.1.52.0.544 |
stnPortDeInsertedThis trap is sent when a stations port's link state
turns off while the management state of the port is
Enabled. TRAP-TYPE .1.3.6.1.4.1.52.0.545 |
boardRingSpeedFaultThis trap is sent when a 'active NON-93 series' board
enters the ring speed fault state due to a station or ring
port attaching to the board as a different speed than the
board is configured for. TRAP-TYPE .1.3.6.1.4.1.52.0.546 |
boardRingSpeedFaultClearedThis trap is sent when a board leaves the ring
speed fault state. TRAP-TYPE .1.3.6.1.4.1.52.0.547 |
ringPortWrappedThis trap is sent when a ring port wraps when its
management state is Active, without regard for the
selected type of the ring port. TRAP-TYPE .1.3.6.1.4.1.52.0.548 |
ringPortWrapClearedThis trap is sent when a ring port unwraps when its
management state is Active, without regard for the
selected type of the ring port. TRAP-TYPE .1.3.6.1.4.1.52.0.549 |
beaconingStateThis trap occurs, if beacon recovery is enabled,
when Beaconing, Ring Purging or Claim Tokens are detected
on the ring while the ring is in the Operational state, or
when the Beacon contains different information than
the last Beacon received. TRAP-TYPE .1.3.6.1.4.1.52.0.550 |
beaconingStateClearedThis trap occurs when a ring returns to the
Operational state. TRAP-TYPE .1.3.6.1.4.1.52.0.551 |
stnAddedThis trap is sent when a new station is added to the
security allowed list. TRAP-TYPE .1.3.6.1.4.1.52.0.552 |
stnRemovedThis trap is sent when a station is rejected
from the ring with a REMOVE MAC command sent
by the ring security. TRAP-TYPE .1.3.6.1.4.1.52.0.553 |
removeStnFailureThis trap is sent when a station breaks through security
and cannot be removed from the ring. TRAP-TYPE .1.3.6.1.4.1.52.0.554 |
ringSecurityPortRemovedThis trap is sent when a ring security break
has been corrected, and reports that a port was
removed (disabled) in the process of correcting the condition. TRAP-TYPE .1.3.6.1.4.1.52.0.555 |
beaconRecoveryPortRemovedThis trap is sent after a fault recovery condition
has been corrected, and reports that a port was
removed in the process of correcting the condition. TRAP-TYPE .1.3.6.1.4.1.52.0.556 |
beaconRecoveryPortGroupBypassedThis trap is sent after a fault recovery condition
has been corrected, and reports that a port group was
bypassed in the process of correcting the condition. TRAP-TYPE .1.3.6.1.4.1.52.0.557 |
beaconRecoveryBoardBypassedThis trap is sent after a fault recovery condition
has been corrected, and reports that a board was
bypassed in the process of correcting the condition. TRAP-TYPE .1.3.6.1.4.1.52.0.558 |
portLinkViolationThis trap is sent when a port link state turns on
and the port's management state is Disabled. TRAP-TYPE .1.3.6.1.4.1.52.0.559 |
portLinkViolationClearedThis trap is sent when a port link state turns off
and the port's management state is Disabled. TRAP-TYPE .1.3.6.1.4.1.52.0.560 |
ringPurgeTotalThresholdThis trap is sent when ring purge errors have exceeded
the specified threshold value. TRAP-TYPE .1.3.6.1.4.1.52.0.561 |
amErrorsTotalThresholdThis trap is sent when Active Monitor errors have exceeded
the specified threshold value. TRAP-TYPE .1.3.6.1.4.1.52.0.562 |
tokenErrorsTotalThresholdThis trap is sent when Token errors have exceeded
the specified threshold value. TRAP-TYPE .1.3.6.1.4.1.52.0.563 |
claimTokenTotalThresholdThis trap is sent when claim tokens have exceeded
the specified threshold value. TRAP-TYPE .1.3.6.1.4.1.52.0.564 |
lostFramesTotalThresholdThis trap is sent when the Lost Frame count has exceeded
the specified threshold value. TRAP-TYPE .1.3.6.1.4.1.52.0.565 |
frameCountTotalThresholdThis trap is sent when the frame count has exceeded
the specified threshold value. TRAP-TYPE .1.3.6.1.4.1.52.0.566 |
lineErrorsStnThresholdThis trap is sent when the line errors have exceeded
the specified threshold value for the station. TRAP-TYPE .1.3.6.1.4.1.52.0.567 |
internalErrorsStnThresholdThis trap is sent when the Lost internal errors have exceeded
the specified threshold value for the station. TRAP-TYPE .1.3.6.1.4.1.52.0.568 |
burstErrorsStnThresholdThis trap is sent when the Lost burst errors have exceeded
the specified threshold value for the station. TRAP-TYPE .1.3.6.1.4.1.52.0.569 |
acErrorsStnThresholdThis trap is sent when address/copied errors have exceeded
the specified threshold value for the station. TRAP-TYPE .1.3.6.1.4.1.52.0.570 |
receiverCongestionStnThresholdThis trap is sent when receiver congestion errors have exceeded
the specified threshold value for the station. TRAP-TYPE .1.3.6.1.4.1.52.0.571 |
ringSpeedPortFaultedThis trap is generated when a port enters the ring speed
fault state due to a station or ring port attaching to the
port at a different speed than the port is configured for. TRAP-TYPE .1.3.6.1.4.1.52.0.572 |
ringSpeedPortFaultedClearedThis trap is generated when a port leaves the ring speed
fault state. TRAP-TYPE .1.3.6.1.4.1.52.0.573 |
tpimInsertedThis trap is generated when a TPIM is installed. TRAP-TYPE .1.3.6.1.4.1.52.0.574 |
tpimRemovedThis trap is generated when a TPIM is removed. TRAP-TYPE .1.3.6.1.4.1.52.0.575 |
neighborNotificationIncThis trap is sent each time the neighbor notification (ring
poll) does not complete. TRAP-TYPE .1.3.6.1.4.1.52.0.576 |
fltRecoveryOscillationThis trap is sent when the ring has oscillated (in
and out of beaconing) when beacon recovery is enabled.
The ring is considered oscillating if it has
failed 21 secs after recovering from the previous. TRAP-TYPE .1.3.6.1.4.1.52.0.577 |
ringPollFailureEventCorrectedThis trap is sent after the management module successfully
recovered the Ring Poll Failure condition. TRAP-TYPE .1.3.6.1.4.1.52.0.578 |
ringPollFailureEventNotCorrectedThis trap is sent after the management module has failed to
recover the Ring Poll Failure condition. The interesting
information includes the interface number and the MAC address
of the last successful ring poll station. TRAP-TYPE .1.3.6.1.4.1.52.0.579 |
sPVPThis trap indicates that a SPVP was rerouted.
The variables indicates the address of a rerouted spvp, the time
stamp of when rerouting occurred, and the cause of rerouting.
The cause codes are as follows:
Unallocated (unassigned) number = 1
No route to specified transit network = 2
No route to destination = 3
Normal call clearing = 16
User busy = 17
No user responding = 18
Call rejected = 21
Number changed = 22
User rejects all calls with calling line
identification restriction (CLIR) = 23
Destination out of order = 27
Invalid number format (address incomplete) = 28
Response to STATUS ENQUIRY = 30
Normal, unspecified = 31
Requested VPCI/VCI not available = 35
VPCI/VCI assignment failure = 36
User cell rate not available = 37
Network out of order = 38
Temporary failure = 41
Access information discarded = 43
No VPCI/VCI available = 45
Resource unavailable, unspecified = 47
Quality of Service unavailable = 49
Bearer capability not authorized = 57
Bearer capability not presently available = 58
Service or option not available, unspecified = 63
Bearer capability not implemented = 65
Unsupported combination of traffic parameters = 73
AAL parameters cannot be supported = 78
Invalid call reference value = 81
Identified channel does not exist = 82
Incompatible destination = 88
Invalid endpoint reference = 89
Invalid transit network selection = 91
Too many pending add party requests = 92
Mandatory information element missing = 96
Message type non-existent or not implemented = 97
Information element non existent or not implemented = 99
Invalid information element contents = 100
Message not compatible with call state = 101
Recovery on timer expiry = 102
Incorrect message length = 104
Protocol error, unspecified = 111 TRAP-TYPE .1.3.6.1.4.1.52.0.580 |
sPVCThis trap indicates that a SPVC was rerouted.
The variables indicates the address of a rerouted spvc, the time
stamp of when rerouting occurred, and the cause of rerouting.
The cause codes are as follows:
Unallocated (unassigned) number = 1
No route to specified transit network = 2
No route to destination = 3
Normal call clearing = 16
User busy = 17
No user responding = 18
Call rejected = 21
Number changed = 22
User rejects all calls with calling line identification
restriction (CLIR) = 23
Destination out of order = 27
Invalid number format (address incomplete) = 28
Response to STATUS ENQUIRY = 30
Normal, unspecified = 31
Requested VPCI/VCI not available = 35
VPCI/VCI assignment failure = 36
User cell rate not available = 37
Network out of order = 38
Temporary failure = 41
Access information discarded = 43
No VPCI/VCI available = 45
Resource unavailable, unspecified = 47
Quality of Service unavailable = 49
Bearer capability not authorized = 57
Bearer capability not presently available = 58
Service or option not available, unspecified = 63
Bearer capability not implemented = 65
Unsupported combination of traffic parameters = 73
AAL parameters cannot be supported = 78
Invalid call reference value = 81
Identified channel does not exist = 82
Incompatible destination = 88
Invalid endpoint reference = 89
Invalid transit network selection = 91
Too many pending add party requests = 92
Mandatory information element missing = 96
Message type non-existent or not implemented = 97
Information element non existent or not implemented = 99
Invalid information element contents = 100
Message not compatible with call state = 101
Recovery on timer expiry = 102
Incorrect message length = 104
Protocol error, unspecified = 111 TRAP-TYPE .1.3.6.1.4.1.52.0.581 |
deviceDiagnosticMessageThis trap is generated for diagnostic purposes. TRAP-TYPE .1.3.6.1.4.1.52.0.703 |
bridgeStatusChangedThis trap is generated when the status of the bridge
changes. TRAP-TYPE .1.3.6.1.4.1.52.0.769 |
aquiredDatabaseFullThis trap is generated when the acquired portion of
the bridge's filtering database is full. TRAP-TYPE .1.3.6.1.4.1.52.0.770 |
boardPortActivateThis Trap is generated when Front Panel Redundancy
changes the active port. TRAP-TYPE .1.3.6.1.4.1.52.0.849 |
boardNightVisionThis trap is generated when night vision turns off or
on. If power to the device is lost, this trap is sent
with a value of 0, indicating that power has been lost
but the device is running on 'night vision'. If power
is not restored within 10 minutes, the device shuts down
completely. If power is restored in that time frame,
the trap is sent with a value of 1 indicating as such. TRAP-TYPE .1.3.6.1.4.1.52.0.900 |
snmpLostContactA LostContact signifies that a the Cabletron hub has lost
contact with the destination IP address host/device. This trap
is only sent at the 'trap-wait' intervals. Note that this trap
indicates a poll failure, not a threshold failure. Threshold
alarms are generated independently. The snmpPollDestination
indicates the lost device. TRAP-TYPE .1.3.6.1.4.1.52.0.1000 |
snmpThresholdTrapThis trap signifies that an OID value/threshold comparison
has failed. The snmpOIDObject specifies which Object Identifier
and instance (destination IP address, owner IP address, and
sequence number) was used to trigger the alarm condition. The
snmpOIDDestination indicates the node address that failed the
OID poll. TRAP-TYPE .1.3.6.1.4.1.52.0.1001 |
snmpReestabContactA ReestabContact signifies that a the Cabletron hub has
reestablished contact with the destination IP address
host/device. This trap is sent immediately after contact
has been reestablished. TRAP-TYPE .1.3.6.1.4.1.52.0.1002 |
ctBroadcastThresholdReachedThis trap is generated when the configured
broadcast threshold on a port is reached and
will include the slot number and port number
the threshold was reached on. TRAP-TYPE .1.3.6.1.4.1.52.0.1003 |
ctLecStatusThis trap is generated when the operational
state of the LAN Emulation Client has changed. TRAP-TYPE .1.3.6.1.4.1.52.0.1004 |
fddiPortConnectStateChangeThis trap is generated for FDDI port connection state
changes. The variables are found in IETF FDDI MIB
RFC-1512. TRAP-TYPE .1.3.6.1.4.1.52.0.1024 |
fddiSMTMasterPortIncreaseThis trap is generated whenever there is an increase in
the number of SMT master ports. TRAP-TYPE .1.3.6.1.4.1.52.0.1025 |
fddiSMTMasterPortDecreaseThis trap is generated anytime there is a decrease in
the number of SMT master ports. TRAP-TYPE .1.3.6.1.4.1.52.0.1026 |
fddiPortActionThis trap is generated for every action against a
FDDI port. The variables are found in IETF FDDI MIB
RFC-1512. TRAP-TYPE .1.3.6.1.4.1.52.0.1027 |
fddiPortLerAlarmThis trap is generated when the long term link
error rate, fddimibPORTLerEstimate, crosses the
fddimibPORTLerAlarm threshold. The variables are
found in IETF FDDI MIB RFC-1512. TRAP-TYPE .1.3.6.1.4.1.52.0.1028 |
fddiModuleFNBbypassedThis trap is generated when a FDDI module
is bypassed on the FNB. TRAP-TYPE .1.3.6.1.4.1.52.0.1030 |
fddiModuleFNBinsertedThis trap is generated when a FDDI module
is inserted on the FNB. TRAP-TYPE .1.3.6.1.4.1.52.0.1031 |
fddiMACRMTStateThis trap is generated when there is a
change in the FDDI ring state. The variables
are found in IETF FDDI MIB RFC-1512. TRAP-TYPE .1.3.6.1.4.1.52.0.1032 |
fddiMACCurrentPathThis trap is generated when there is a
change in the insertion of the MAC to the
FDDI ring. The variables are found in IETF
FDDI MIB RFC-1512. TRAP-TYPE .1.3.6.1.4.1.52.0.1033 |
fddiSMTCFStateThis trap is generated when there is a
change in the attachment configuration for
the station or concentrator. The variables
are found in IETF FDDI MIB RFC-1512. TRAP-TYPE .1.3.6.1.4.1.52.0.1034 |
fddiRingTopologyThis trap is generated when there is a
change in the attachment configuration for
the station or concentrator. It provides
information additional to fddiSMTCFState,
twisted ring conditions in particular. The
variables are found in the Cabletron SMT MIB. TRAP-TYPE .1.3.6.1.4.1.52.0.1035 |
fddiMACFrameErrorRatioThis trap is generated when the frame error
ratio exceeds the frame error threshold,
fddimibMACFrameErrorThreshold. The variables
are found in IETF FDDI MIB RFC-1512. TRAP-TYPE .1.3.6.1.4.1.52.0.1036 |
fddiMACDuplicateMACAddressThis trap is generated when the SMT detects
a duplicate MAC address on the ring. TRAP-TYPE .1.3.6.1.4.1.52.0.1037 |
contLogicalChangesTrapThis trap is generated when any change occurs
in the contLogicalEntryTable group of the container MIB. TRAP-TYPE .1.3.6.1.4.1.52.0.1200 |
contPhysicalChangesTrapThis trap is generated when any change occurs to
contPhysicalEntryTable group of the container MIB. TRAP-TYPE .1.3.6.1.4.1.52.0.1201 |
rtrIpEventLogChangeThis trap is generated for changes to IP event log. TRAP-TYPE .1.3.6.1.4.1.52.0.1280 |
rtrIPXEventLogChangeThis trap is generated whenever an entry is made to the
router IPX event log for where nwIpEventSeverity has a
value of highest(1). TRAP-TYPE .1.3.6.1.4.1.52.0.1281 |
rtrDecIVEventLogChangeThis trap is generated whenever an entry is made to the
router Dec Net IV event log. TRAP-TYPE .1.3.6.1.4.1.52.0.1282 |
rtrAppleEventLogChangeThis trap is generated whenever an entry is made to the
router Apple Talk event log. TRAP-TYPE .1.3.6.1.4.1.52.0.1283 |
rtrAppnEventLogChangeThis trap is generated whenever an entry is made to the
router APPN event log. TRAP-TYPE .1.3.6.1.4.1.52.0.1284 |
nwAppnLsUpWhen a link station becomes active, a trap is
generated. nwAppnFwdLsName identifies the link
station name. TRAP-TYPE .1.3.6.1.4.1.52.0.1285 |
nwAppnLsDownWhen a link station is deactivated, a trap is
generated. nwAppnFwdLsName identifies the link
station name, nwAppnFwdLsAdjCpName identifies the
fully qualified CP name of the adjacent node and
nwAppnFwdLsAdjCpType is the type of that node. TRAP-TYPE .1.3.6.1.4.1.52.0.1286 |
sfpsNewUserThis trap is generated when a new user enters the SFPS
fabric. TRAP-TYPE .1.3.6.1.4.1.52.0.1400 |
sfpsDirectoryViolationThis trap is generated when one of 6 violation types have occurred.
1 UserLock
2 RestrictedPort
3 IPNotLearned
4 IPInvalid
5 RestrictedMobility
6 UserLockSamePort TRAP-TYPE .1.3.6.1.4.1.52.0.1401 |
sfpsSourceBlockedThis trap is generated when a user (source MAC address) has
surpassed the Source Blocker thresholds and is being blocked from
sending traffic on the network. TRAP-TYPE .1.3.6.1.4.1.52.0.1402 |
sfpsFloodSurpressedA destination address has been unresolvable past the thresholds
and is now being flood suppressed (only 1 per X seconds will pass). TRAP-TYPE .1.3.6.1.4.1.52.0.1403 |
sfpsPortToStandbyThis trap is generated when a port has entered standby.
There are different standby states:
9 STAND_BY (manually set)
14 STAND_BY_FCL (one way neighbor)
15 STAND_BY_LOOPED (self originated Hello seen on port)
16 STAND_BY_RTA (redundant access port is standby/backup TRAP-TYPE .1.3.6.1.4.1.52.0.1404 |
sfpsPortFromStandbyThis trap is generated when a port that was in standby is
now not in standby. Most common is that either a one-way
neighbor situation is gone or a standby RA port is now primary. TRAP-TYPE .1.3.6.1.4.1.52.0.1405 |
nmsMapAdded} TRAP-TYPE .1.3.6.1.4.1.52.0.1536 |
nmsMapDeleted} TRAP-TYPE .1.3.6.1.4.1.52.0.1537 |
nmsMapChanged} TRAP-TYPE .1.3.6.1.4.1.52.0.1538 |
nmsMapOpened} TRAP-TYPE .1.3.6.1.4.1.52.0.1539 |
nmsMapClosed} TRAP-TYPE .1.3.6.1.4.1.52.0.1540 |
nmsElementAdded} TRAP-TYPE .1.3.6.1.4.1.52.0.1541 |
nmsElementDeleted} TRAP-TYPE .1.3.6.1.4.1.52.0.1542 |
nmsElementChanged} TRAP-TYPE .1.3.6.1.4.1.52.0.1543 |
nmsSymbolAdded} TRAP-TYPE .1.3.6.1.4.1.52.0.1544 |
nmsSymbolDeleted} TRAP-TYPE .1.3.6.1.4.1.52.0.1545 |
nmsSymbolChanged} TRAP-TYPE .1.3.6.1.4.1.52.0.1546 |
wgPsInstalledThis trap is generated when the device detects that the
power supply has been installed. TRAP-TYPE .1.3.6.1.4.1.52.0.1800 |
wgPsRemovedThis trap is generated when the device detects that the
power supply has been removed. TRAP-TYPE .1.3.6.1.4.1.52.0.1801 |
wgPsNormalThis trap is generated when the device detects that the power
supply has returned to normal. TRAP-TYPE .1.3.6.1.4.1.52.0.1802 |
wgPsFailThis trap is generated when the device detects that the power
supply has failed. TRAP-TYPE .1.3.6.1.4.1.52.0.1803 |
wgPsRedundantThis trap is generated when the device detects that the power
supply is in the redundant state. TRAP-TYPE .1.3.6.1.4.1.52.0.1804 |
wgPsNotRedundantThis trap is generated when the device detects that the power
supply is not in the redundant state. TRAP-TYPE .1.3.6.1.4.1.52.0.1805 |
wgBoardInsertedThis trap is generated when a module is inserted. TRAP-TYPE .1.3.6.1.4.1.52.0.1806 |
wgBoardRemovedThis trap is generated when a module is removed. TRAP-TYPE .1.3.6.1.4.1.52.0.1807 |
aPCLineFailThis trap is generated in the event of an AC
utility line failure TRAP-TYPE .1.3.6.1.4.1.52.0.4353 |
aPCLineFailRecoveryThis trap is generated when the UPS switches back
to line, and only if the aPCLineFail trap was issued
first TRAP-TYPE .1.3.6.1.4.1.52.0.4354 |
aPCLowBatteryThis trap is generated in the event that the UPS'
battery is found to be low TRAP-TYPE .1.3.6.1.4.1.52.0.4355 |
aPCLowBatteryRecoveryThis trap is generated when the UPS' battery has
charged above the low-battery point, and only if the
aPCLowBattery trap was issued first TRAP-TYPE .1.3.6.1.4.1.52.0.4356 |
aPCAbnormalConditionThis trap is generated in the event that the UPS
has entered an abnormal condition, such as an
overload or trip on low battery. This trap is also
sent, when the UPS is first turned on. TRAP-TYPE .1.3.6.1.4.1.52.0.4357 |
aPCAbnormConditionRecoveryThis trap is generated when the UPS has recovered
from an abnormal condition, and only if the
aPCAbnormalCondition trap was issued first TRAP-TYPE .1.3.6.1.4.1.52.0.4358 |
aPCShuttingDownThis trap is generated in the event that the UPS
has been ordered to shut itself, or the load, off
over the serial line. TRAP-TYPE .1.3.6.1.4.1.52.0.4359 |
emTermOverVoltageThis trap is generated when the term power bus is over voltage. TRAP-TYPE .1.3.6.1.4.1.52.0.11001 |
emTermUnderVoltageThis trap is generated when the term power bus is under voltage. TRAP-TYPE .1.3.6.1.4.1.52.0.11002 |
emTermNormalVoltageThis trap is generated when the term power bus is at an acceptable
voltage. It will only be sent out after a trap was sent to say that
the term voltage was under or over. TRAP-TYPE .1.3.6.1.4.1.52.0.11003 |
chHotTempThis trap is generated because the chassis is hot. TRAP-TYPE .1.3.6.1.4.1.52.0.11004 |
chWarmTempThis trap is generated because the chassis is warm. TRAP-TYPE .1.3.6.1.4.1.52.0.11005 |
chCoolTempThis trap is generated because the chassis is cool. TRAP-TYPE .1.3.6.1.4.1.52.0.11006 |
chColdTempThis trap is generated because the chassis is cold. TRAP-TYPE .1.3.6.1.4.1.52.0.11007 |
chTempOKThis trap is generated because the chassis has returned to normal
after being warm, hot, cool or cold. TRAP-TYPE .1.3.6.1.4.1.52.0.11008 |
chTempSensorBrokenThis trap is generated when the chassis's temperature sensor is
broken. TRAP-TYPE .1.3.6.1.4.1.52.0.11009 |
chHumidityStaticRiskThis trap is generated when the chassis determines there is a
humidity static risk. TRAP-TYPE .1.3.6.1.4.1.52.0.11010 |
chHumidityNormalThis trap is generated when the chassis determines the humidity
has returned to normal after being moist or static risk. TRAP-TYPE .1.3.6.1.4.1.52.0.11011 |
chHumidityMoistThis trap is generated when the chassis determines there is a
humidity moist risk. TRAP-TYPE .1.3.6.1.4.1.52.0.11012 |
chHumiditySensorBrokenThis trap is generated when the chassis determines the humidity
sensor is broken. TRAP-TYPE .1.3.6.1.4.1.52.0.11013 |
chMod1INBInstalledThis trap is generated when the INV termination has been installed
for module 1. TRAP-TYPE .1.3.6.1.4.1.52.0.11014 |
chMod1INBFaultyThis trap is generated when the INV termination is faulty for
module 1. TRAP-TYPE .1.3.6.1.4.1.52.0.11015 |
chMod1INBRemovedThis trap is generated when the INV termination has been removed for
module 1. TRAP-TYPE .1.3.6.1.4.1.52.0.11016 |
chMod1INBNormalThis trap is generated when the INV termination (module 1) has
returned to normal after already sending a trap to say it was faulty. TRAP-TYPE .1.3.6.1.4.1.52.0.11017 |
chMod2INBInstalledThis trap is generated when the INV termination has been installed
for module 2. TRAP-TYPE .1.3.6.1.4.1.52.0.11018 |
chMod2INBFaultyThis trap is generated when the INV termination is faulty for
module 2. TRAP-TYPE .1.3.6.1.4.1.52.0.11019 |
chMod2INBRemovedThis trap is generated when the INV termination has been removed for
module 2. TRAP-TYPE .1.3.6.1.4.1.52.0.11020 |
chMod2INBNormalThis trap is generated when the INV termination (module 2) has
returned to normal after already sending a trap to say it was faulty. TRAP-TYPE .1.3.6.1.4.1.52.0.11021 |
emFanFailureThis trap is generated when the chassis detects a fan failure. TRAP-TYPE .1.3.6.1.4.1.52.0.11022 |
boardHotTempShutdownThis trap is generated because a board is hot and the board has shut
itself down. TRAP-TYPE .1.3.6.1.4.1.52.0.11023 |
boardWarmTempThis trap is generated because a board is warm. TRAP-TYPE .1.3.6.1.4.1.52.0.11024 |
boardCoolTempThis trap is generated because a board is cool. TRAP-TYPE .1.3.6.1.4.1.52.0.11025 |
boardColdTempThis trap is generated because a board is cold. TRAP-TYPE .1.3.6.1.4.1.52.0.11026 |
boardTempOKThis trap is generated because a board has returned to normal after
being warm or hot. TRAP-TYPE .1.3.6.1.4.1.52.0.11027 |
boardTempSensorBrokenThis trap is generated when the board's temperature sensor is
broken. TRAP-TYPE .1.3.6.1.4.1.52.0.11028 |
boardTempHotNoAdminThis trap is generated because a board is hot. TRAP-TYPE .1.3.6.1.4.1.52.0.11029 |
boardRelWarmTempThis trap is generated because a board's relative temp is warm. TRAP-TYPE .1.3.6.1.4.1.52.0.11030 |
boardRelTempOKThis trap is generated because a board's relative temp has returned
to normal after being warm or hot. TRAP-TYPE .1.3.6.1.4.1.52.0.11031 |
boardRelTempHotNoAdminThis trap is generated because a board's relative temp is hot but it
cannot shutdown. It will need to be turned off remotely. TRAP-TYPE .1.3.6.1.4.1.52.0.11032 |
boardRelTempHotShutdownThis trap is generated when the board's relative temperature is hot
and is being powered off. TRAP-TYPE .1.3.6.1.4.1.52.0.11033 |
boardRelWarmTempMaxFansThis trap is generated because a board's relative temp is warm. The
fans are on MAX. TRAP-TYPE .1.3.6.1.4.1.52.0.11034 |
boardRelTempOKMaxFansThis trap is generated because a board's relative temp has returned
to normal after being warm or hot. The fans are on MAX. TRAP-TYPE .1.3.6.1.4.1.52.0.11035 |
boardRelTempHotNoAdminMaxFansThis trap is generated because a board's relative temp is hot but it
cannot shutdown. It will need to be turned off remotely. The fans are
on MAX. TRAP-TYPE .1.3.6.1.4.1.52.0.11036 |
boardRelTempHotShutdownMaxFansThis trap is generated when the board's relative temperature is hot
and is being powered off. The fans are on MAX. TRAP-TYPE .1.3.6.1.4.1.52.0.11037 |
boardInputVoltageOverMaxThis trap is generated because a boards input voltage is over max. TRAP-TYPE .1.3.6.1.4.1.52.0.11038 |
boardInputVoltageUnderMinThis trap is generated because a boards input voltage is under
minimum. TRAP-TYPE .1.3.6.1.4.1.52.0.11039 |
boardInputVoltageOKThis trap is generated because a board input voltage has returned to
normal after being over or under. TRAP-TYPE .1.3.6.1.4.1.52.0.11040 |
boardOutputVoltageOverMaxThis trap is generated because a board output voltage is over MAX. TRAP-TYPE .1.3.6.1.4.1.52.0.11041 |
boardOutputVoltageUnderMinThis trap is generated because a board output voltage is under MIN. TRAP-TYPE .1.3.6.1.4.1.52.0.11042 |
boardOutputVoltageOKThis trap is generated because a board output voltage has returned to
normal after being over or under. TRAP-TYPE .1.3.6.1.4.1.52.0.11043 |
boardAuxVoltageOverMaxThis trap is generated because a boards auxiliary voltage is over
MAX. TRAP-TYPE .1.3.6.1.4.1.52.0.11044 |
boardAuxVoltageUnderMinThis trap is generated because a board auxiliary voltage is under
MIN. TRAP-TYPE .1.3.6.1.4.1.52.0.11045 |
boardAuxVoltageOKThis trap is generated because a board auxiliary voltage has returned
to normal after being over or under. TRAP-TYPE .1.3.6.1.4.1.52.0.11046 |
boardInputCurrentOverMaxShutdownThis trap is generated because a board input current is
over MAX. The power supply has therefore been shutdown. TRAP-TYPE .1.3.6.1.4.1.52.0.11047 |
boardOutputCurrentOverMaxShutdownThis trap is generated because a boards output current is
over MAX. The power supply has therefore been shutdown. TRAP-TYPE .1.3.6.1.4.1.52.0.11048 |
boardInputCurrentOverMaxThis trap is generated because a board input current is
over MAX. The ability of the power supply to turn itself off has been
disabled therefore outside intervention is needed. TRAP-TYPE .1.3.6.1.4.1.52.0.11049 |
boardOutputCurrentOverMaxThis trap is generated because a board output current is
over MAX. The ability of the power supply to turn itself off has been
disabled therefore outside intervention is needed. TRAP-TYPE .1.3.6.1.4.1.52.0.11050 |
boardRemotePowerOffThis trap is generated because the board is being powered
off due to outside intervention. TRAP-TYPE .1.3.6.1.4.1.52.0.11051 |
boardRemotePowerOnThis trap is generated because the board is being powered
on due to outside intervention. TRAP-TYPE .1.3.6.1.4.1.52.0.11052 |
boardRemotePowerResetThis trap is generated because the board is being reset due to
outside intervention. TRAP-TYPE .1.3.6.1.4.1.52.0.11053 |
boardPowerOnThis trap is generated because the board power has been powered on. TRAP-TYPE .1.3.6.1.4.1.52.0.11054 |
boardPowerOffThis trap is generated because the board power has been powered off. TRAP-TYPE .1.3.6.1.4.1.52.0.11055 |
boardPowerResetThis trap is generated because the board has been reset. TRAP-TYPE .1.3.6.1.4.1.52.0.11056 |
boardRemOverCurrentShutdownThis trap is generated because the board has been shutdown remotely
due to being over current. TRAP-TYPE .1.3.6.1.4.1.52.0.11057 |
boardRemPowerConservationShutdownThis trap is generated because the board has been shutdown remotely
due to power conservation. TRAP-TYPE .1.3.6.1.4.1.52.0.11058 |
boardRemTemperatureShutdownThis trap is generated because the board has been shutdown remotely
due to it's temperature. TRAP-TYPE .1.3.6.1.4.1.52.0.11059 |
boardReqFPDisableDCDCThis trap is generated because the board has had an unauthorized
front panel disable. TRAP-TYPE .1.3.6.1.4.1.52.0.11060 |
boardFPDisableDCDCThis trap is generated because the board has been disabled through
the front panel. TRAP-TYPE .1.3.6.1.4.1.52.0.11061 |
boardReqFPEnableDCDCThis trap is generated because the board has had an unauthorized
front panel enable. TRAP-TYPE .1.3.6.1.4.1.52.0.11062 |
boardFPEnableDCDCThis trap is generated because the board has been enabled through the
front panel. TRAP-TYPE .1.3.6.1.4.1.52.0.11063 |
boardReqFPResetDCDCThis trap is generated because the board has had an unauthorized
front panel reset. TRAP-TYPE .1.3.6.1.4.1.52.0.11064 |
boardFPResetDCDCThis trap is generated because the board has been reset through the
front panel. TRAP-TYPE .1.3.6.1.4.1.52.0.11065 |
boardADConvertorFailureThis trap is generated because the board's A/D converter is broken. TRAP-TYPE .1.3.6.1.4.1.52.0.11066 |
boardPICFailureThis trap is generated because of a board PIC failure. TRAP-TYPE .1.3.6.1.4.1.52.0.11067 |
boardPICOkThis trap is generated because the board PIC is now OK.
This trap will only be sent AFTER a PIC failure trap has been
generated. TRAP-TYPE .1.3.6.1.4.1.52.0.11068 |
boardLLAPDupAddressThis trap is generated when the board LLAP address already exists
in this chassis. TRAP-TYPE .1.3.6.1.4.1.52.0.11069 |
boardMailboxFailureThis trap is generated because of a board mailbox failure. TRAP-TYPE .1.3.6.1.4.1.52.0.11070 |
boardMailboxOKThis trap is generated because the board mailbox is now OK. TRAP-TYPE .1.3.6.1.4.1.52.0.11071 |
psACHotTempShutdownThis trap is generated because an AC power supply is hot and the
power supply has shut itself down. TRAP-TYPE .1.3.6.1.4.1.52.0.11072 |
psACWarmTempThis trap is generated because an AC power supply is warm. TRAP-TYPE .1.3.6.1.4.1.52.0.11073 |
psACTempOKThis trap is generated because an AC power supply has returned
to normal after being warm or hot. TRAP-TYPE .1.3.6.1.4.1.52.0.11074 |
psACTempOKNoAdminThis trap is generated because an AC power supply has returned
to normal after being shutdown remotely. It will need to be powerOn
remotely. TRAP-TYPE .1.3.6.1.4.1.52.0.11075 |
psACTempSensorBrokenThis trap is generated when the AC power supply's temperature
sensor is broken. TRAP-TYPE .1.3.6.1.4.1.52.0.11076 |
psACTempHotThis trap is generated because an AC power supply is hot. TRAP-TYPE .1.3.6.1.4.1.52.0.11077 |
psACInputVoltageOverMaxThis trap is generated because an AC power supply input voltage
is over max. TRAP-TYPE .1.3.6.1.4.1.52.0.11078 |
psACInputVoltageUnderMinThis trap is generated because an AC power supply input voltage
is under minimum. TRAP-TYPE .1.3.6.1.4.1.52.0.11079 |
psACInputVoltageOKThis trap is generated because an AC power supply input voltage has
returned to normal after being over or under. TRAP-TYPE .1.3.6.1.4.1.52.0.11080 |
psACSystemVoltageOverMaxThis trap is generated because an AC power supply system voltage is
over MAX. TRAP-TYPE .1.3.6.1.4.1.52.0.11081 |
psACSystemVoltageUnderMinThis trap is generated because an AC power supply system voltage is
under MIN. TRAP-TYPE .1.3.6.1.4.1.52.0.11082 |
psACSystemVoltageOKThis trap is generated because an AC power supply system voltage has
returned to normal after being over or under. TRAP-TYPE .1.3.6.1.4.1.52.0.11083 |
psACLogicVoltageOverMaxThis trap is generated because an AC power supply logic voltage is
over MAX. TRAP-TYPE .1.3.6.1.4.1.52.0.11084 |
psACLogicVoltageUnderMinThis trap is generated because an AC power supply logic voltage is
under MIN. TRAP-TYPE .1.3.6.1.4.1.52.0.11085 |
psACLogicVoltageOKThis trap is generated because an AC power supply logic voltage has
returned to normal after being over or under. TRAP-TYPE .1.3.6.1.4.1.52.0.11086 |
psACTermVoltageOverMaxThis trap is generated because an AC power supply term voltage is
over MAX. TRAP-TYPE .1.3.6.1.4.1.52.0.11087 |
psACTermVoltageUnderMinThis trap is generated because an AC power supply term voltage is
under MIN. TRAP-TYPE .1.3.6.1.4.1.52.0.11088 |
psACTermVoltageOKThis trap is generated because an AC power supply term voltage has
returned to normal after being over or under. TRAP-TYPE .1.3.6.1.4.1.52.0.11089 |
psACLogicSenseCurrentOverMaxThis trap is generated because an AC power supply logic current is
over MAX. The ability of the power supply to turn itself off has been
disabled therefore outside intervention is needed. TRAP-TYPE .1.3.6.1.4.1.52.0.11090 |
psACTermSenseCurrentOverMaxThis trap is generated because an AC power supply term current is
over MAX. The ability of the power supply to turn itself off has been
disabled therefore outside intervention is needed. TRAP-TYPE .1.3.6.1.4.1.52.0.11091 |
psACInputCurrentOverMaxShutdownThis trap is generated because an AC power supply input current is
over MAX. The power supply has therefore been shutdown. TRAP-TYPE .1.3.6.1.4.1.52.0.11092 |
psACSystemCurrentOverMaxShutdownThis trap is generated because an AC power supply system current is
over MAX. The power supply has therefore been shutdown. TRAP-TYPE .1.3.6.1.4.1.52.0.11093 |
psACLogicCurrentOverMaxShutdownThis trap is generated because an AC power supply logic current is
over MAX. The power supply has therefore been shutdown. TRAP-TYPE .1.3.6.1.4.1.52.0.11094 |
psACTermCurrentOverMaxShutdownThis trap is generated because an AC power supply term current is
over MAX. The power supply has therefore been shutdown. TRAP-TYPE .1.3.6.1.4.1.52.0.11095 |
psACLogicSenseCurrentOverMaxShutdownThis trap is generated because an AC power supply logic sense current
is over MAX. The power supply has therefore been shutdown. TRAP-TYPE .1.3.6.1.4.1.52.0.11096 |
psACTermSenseCurrentOverMaxShutdownThis trap is generated because an AC power supply term sense current
is over MAX. The power supply has therefore been shutdown. TRAP-TYPE .1.3.6.1.4.1.52.0.11097 |
psACInputCurrentOverMaxThis trap is generated because an AC power supply input current is
over MAX. The ability of the power supply to turn itself off has been
disabled therefore outside intervention is needed. TRAP-TYPE .1.3.6.1.4.1.52.0.11098 |
psACSystemCurrentOverMaxThis trap is generated because an AC power supply system current is
over MAX. The ability of the power supply to turn itself off has been
disabled therefore outside intervention is needed. TRAP-TYPE .1.3.6.1.4.1.52.0.11099 |
psACLogicCurrentOverMaxThis trap is generated because an AC power supply logic current is
over MAX. The ability of the power supply to turn itself off has been
disabled therefore outside intervention is needed. TRAP-TYPE .1.3.6.1.4.1.52.0.11100 |
psACTermCurrentOverMaxThis trap is generated because an AC power supply term current is
over MAX. The ability of the power supply to turn itself off has been
disabled therefore outside intervention is needed. TRAP-TYPE .1.3.6.1.4.1.52.0.11101 |
psACRemotePowerOffThis trap is generated because the AC power supply is being powered
off due to outside intervention. TRAP-TYPE .1.3.6.1.4.1.52.0.11102 |
psACSystemPowerOnThis trap is generated because the AC power supply system power has
been powered on. TRAP-TYPE .1.3.6.1.4.1.52.0.11103 |
psACSystemPowerOffThis trap is generated because the AC power supply system power has
been powered off. TRAP-TYPE .1.3.6.1.4.1.52.0.11104 |
psACLogicPowerOnThis trap is generated because the AC power supply logic power has
been powered on. TRAP-TYPE .1.3.6.1.4.1.52.0.11105 |
psACLogicPowerOffThis trap is generated because the AC power supply logic power has
been powered off. TRAP-TYPE .1.3.6.1.4.1.52.0.11106 |
psACTermPowerOnThis trap is generated because the AC power supply term power has
been powered on. TRAP-TYPE .1.3.6.1.4.1.52.0.11107 |
psACTermPowerOffThis trap is generated because the AC power supply term power has
been powered off. TRAP-TYPE .1.3.6.1.4.1.52.0.11108 |
psACRemOverCurrentShutdownThis trap is generated because the AC power supply has been shutdown
remotely due to being over current. TRAP-TYPE .1.3.6.1.4.1.52.0.11109 |
psACRemPowerConservationShutdownThis trap is generated because the AC power supply has been shutdown
remotely due to power conservation. TRAP-TYPE .1.3.6.1.4.1.52.0.11110 |
psACADConvertorFailureThis trap is generated because the AC power supply A/D converter
is broken. TRAP-TYPE .1.3.6.1.4.1.52.0.11111 |
psACPICFailureThis trap is generated because of an AC power supply PIC failure. TRAP-TYPE .1.3.6.1.4.1.52.0.11112 |
psACPICOkThis trap is generated because the AC power supply PIC is now OK.
This trap will only be sent AFTER a PIC failure trap has been
generated. TRAP-TYPE .1.3.6.1.4.1.52.0.11113 |
psACLLAPDupAddressThis trap is generated when the AC power supply LLAP address already
exists in this chassis. TRAP-TYPE .1.3.6.1.4.1.52.0.11114 |
psACFanFailureThis trap is generated because of an AC power supply fan failure. TRAP-TYPE .1.3.6.1.4.1.52.0.11115 |
psACFanOKThis trap is generated because the AC power supply fan is now OK.
This trap will only be sent AFTER a fan failure trap has been
generated. TRAP-TYPE .1.3.6.1.4.1.52.0.11116 |
psDCHotTempShutdownThis trap is generated because an DC power supply is hot and the
power supply has shut itself down. TRAP-TYPE .1.3.6.1.4.1.52.0.11117 |
psDCWarmTempThis trap is generated because an DC power supply is warm. TRAP-TYPE .1.3.6.1.4.1.52.0.11118 |
psDCTempOKThis trap is generated because an DC power supply has returned
to normal after being warm or hot. TRAP-TYPE .1.3.6.1.4.1.52.0.11119 |
psDCTempOKNoAdminThis trap is generated because an DC power supply has returned
to normal after being shutdown remotely. It will need to be powerOn
remotely. TRAP-TYPE .1.3.6.1.4.1.52.0.11120 |
psDCTempSensorBrokenThis trap is generated when the DC power supply's temperature
sensor is broken. TRAP-TYPE .1.3.6.1.4.1.52.0.11121 |
psDCTempHotThis trap is generated because an DC power supply is hot. TRAP-TYPE .1.3.6.1.4.1.52.0.11122 |
psDCInputVoltageOverMaxThis trap is generated because an DC power supply input voltage
is over max. TRAP-TYPE .1.3.6.1.4.1.52.0.11123 |
psDCInputVoltageUnderMinThis trap is generated because an DC power supply input voltage
is under minimum. TRAP-TYPE .1.3.6.1.4.1.52.0.11124 |
psDCInputVoltageOKThis trap is generated because an DC power supply input voltage has
returned to normal after being over or under. TRAP-TYPE .1.3.6.1.4.1.52.0.11125 |
psDCSystemVoltageOverMaxThis trap is generated because an DC power supply system voltage is
over MAX. TRAP-TYPE .1.3.6.1.4.1.52.0.11126 |
psDCSystemVoltageUnderMinThis trap is generated because an DC power supply system voltage is
under MIN. TRAP-TYPE .1.3.6.1.4.1.52.0.11127 |
psDCSystemVoltageOKThis trap is generated because an DC power supply system voltage has
returned to normal after being over or under. TRAP-TYPE .1.3.6.1.4.1.52.0.11128 |
psDCLogicVoltageOverMaxThis trap is generated because an DC power supply logic voltage is
over MAX. TRAP-TYPE .1.3.6.1.4.1.52.0.11129 |
psDCLogicVoltageUnderMinThis trap is generated because an DC power supply logic voltage is
under MIN. TRAP-TYPE .1.3.6.1.4.1.52.0.11130 |
psDCLogicVoltageOKThis trap is generated because an DC power supply logic voltage has
returned to normal after being over or under. TRAP-TYPE .1.3.6.1.4.1.52.0.11131 |
psDCTermVoltageOverMaxThis trap is generated because an DC power supply term voltage is
over MAX. TRAP-TYPE .1.3.6.1.4.1.52.0.11132 |
psDCTermVoltageUnderMinThis trap is generated because an DC power supply term voltage is
under MIN. TRAP-TYPE .1.3.6.1.4.1.52.0.11133 |
psDCTermVoltageOKThis trap is generated because an DC power supply term voltage has
returned to normal after being over or under. TRAP-TYPE .1.3.6.1.4.1.52.0.11134 |
psDCLogicSenseCurrentOverMaxThis trap is generated because an DC power supply logic current is
over MAX. The ability of the power supply to turn itself off has been
disabled therefore outside intervention is needed. TRAP-TYPE .1.3.6.1.4.1.52.0.11135 |
psDCTermSenseCurrentOverMaxThis trap is generated because an DC power supply term current is
over MAX. The ability of the power supply to turn itself off has been
disabled therefore outside intervention is needed. TRAP-TYPE .1.3.6.1.4.1.52.0.11136 |
psDCInputCurrentOverMaxShutdownThis trap is generated because an DC power supply input current is
over MAX. The power supply has therefore been shutdown. TRAP-TYPE .1.3.6.1.4.1.52.0.11137 |
psDCSystemCurrentOverMaxShutdownThis trap is generated because an DC power supply system current is
over MAX. The power supply has therefore been shutdown. TRAP-TYPE .1.3.6.1.4.1.52.0.11138 |
psDCLogicCurrentOverMaxShutdownThis trap is generated because an DC power supply logic current is
over MAX. The power supply has therefore been shutdown. TRAP-TYPE .1.3.6.1.4.1.52.0.11139 |
psDCTermCurrentOverMaxShutdownThis trap is generated because an DC power supply term current is
over MAX. The power supply has therefore been shutdown. TRAP-TYPE .1.3.6.1.4.1.52.0.11140 |
psDCLogicSenseCurrentOverMaxShutdownThis trap is generated because an DC power supply logic sense current
is over MAX. The power supply has therefore been shutdown. TRAP-TYPE .1.3.6.1.4.1.52.0.11141 |
psDCTermSenseCurrentOverMaxShutdownThis trap is generated because an DC power supply term sense current
is over MAX. The power supply has therefore been shutdown. TRAP-TYPE .1.3.6.1.4.1.52.0.11142 |
psDCInputCurrentOverMaxThis trap is generated because an DC power supply input current is
over MAX. The ability of the power supply to turn itself off has been
disabled therefore outside intervention is needed. TRAP-TYPE .1.3.6.1.4.1.52.0.11143 |
psDCSystemCurrentOverMaxThis trap is generated because an DC power supply system current is
over MAX. The ability of the power supply to turn itself off has been
disabled therefore outside intervention is needed. TRAP-TYPE .1.3.6.1.4.1.52.0.11144 |
psDCLogicCurrentOverMaxThis trap is generated because an DC power supply logic current is
over MAX. The ability of the power supply to turn itself off has been
disabled therefore outside intervention is needed. TRAP-TYPE .1.3.6.1.4.1.52.0.11145 |
psDCTermCurrentOverMaxThis trap is generated because an DC power supply term current is
over MAX. The ability of the power supply to turn itself off has been
disabled therefore outside intervention is needed. TRAP-TYPE .1.3.6.1.4.1.52.0.11146 |
psDCRemotePowerOffThis trap is generated because the DC power supply is being powered
off due to outside intervention. TRAP-TYPE .1.3.6.1.4.1.52.0.11147 |
psDCSystemPowerOnThis trap is generated because the DC power supply system power has
been powered on. TRAP-TYPE .1.3.6.1.4.1.52.0.11148 |
psDCSystemPowerOffThis trap is generated because the DC power supply system power has
been powered off. TRAP-TYPE .1.3.6.1.4.1.52.0.11149 |
psDCLogicPowerOnThis trap is generated because the DC power supply logic power has
been powered on. TRAP-TYPE .1.3.6.1.4.1.52.0.11150 |
psDCLogicPowerOffThis trap is generated because the DC power supply logic power has
been powered off. TRAP-TYPE .1.3.6.1.4.1.52.0.11151 |
psDCTermPowerOnThis trap is generated because the DC power supply term power has
been powered on. TRAP-TYPE .1.3.6.1.4.1.52.0.11152 |
psDCTermPowerOffThis trap is generated because the DC power supply term power has
been powered off. TRAP-TYPE .1.3.6.1.4.1.52.0.11153 |
psDCRemOverCurrentShutdownThis trap is generated because the DC power supply has been shutdown
remotely due to being over current. TRAP-TYPE .1.3.6.1.4.1.52.0.11154 |
psDCRemPowerConservationShutdownThis trap is generated because the DC power supply has been shutdown
remotely due to power conservation. TRAP-TYPE .1.3.6.1.4.1.52.0.11155 |
psDCADConvertorFailureThis trap is generated because the DC power supply A/D converter
is broken. TRAP-TYPE .1.3.6.1.4.1.52.0.11156 |
psADPICFailureThis trap is generated because of an DC power supply PIC failure. TRAP-TYPE .1.3.6.1.4.1.52.0.11157 |
psADPICOkThis trap is generated because the DC power supply PIC is now OK.
This trap will only be sent AFTER a PIC failure trap has been
generated. TRAP-TYPE .1.3.6.1.4.1.52.0.11158 |
psADLLAPDupAddressThis trap is generated when the DC power supply LLAP address already
exists in this chassis. TRAP-TYPE .1.3.6.1.4.1.52.0.11159 |
psADFanFailureThis trap is generated because of an DC power supply fan failure. TRAP-TYPE .1.3.6.1.4.1.52.0.11160 |
psDCFanOKThis trap is generated because the DC power supply fan is now OK.
This trap will only be sent AFTER a fan failure trap has been
generated. TRAP-TYPE .1.3.6.1.4.1.52.0.11161 |
psADConvertorFailureThis trap is generated because the power supply A/D converter
is broken. TRAP-TYPE .1.3.6.1.4.1.52.0.11162 |
psPicFailureThis trap is generated because of a power supply PIC failure. TRAP-TYPE .1.3.6.1.4.1.52.0.11163 |
psPICokThis trap is generated because the power supply PIC is now OK.
This trap will only be sent AFTER a PIC failure trap has been
generated. TRAP-TYPE .1.3.6.1.4.1.52.0.11164 |
psLLAPDupAddressThis trap is generated when the power supply LLAP address already
exists in this chassis. TRAP-TYPE .1.3.6.1.4.1.52.0.11165 |
chEnvAmbientTempChangesThis trap is generated for each and every time the chassis
ambient temperature crosses over a threshold value
of either one of the chassis set thresholds chEnvAmbientHot,
chEnvAmbientWarm, chEnvAmbientCool, or chEnvAmbientCold
to another. This trap is also sent when the chassis temperature
sensor is detected to be broken or not supported. TRAP-TYPE .1.3.6.1.4.1.52.0.11166 |
chEnvHumidityChangesThis trap is generated for each and every time the chassis
humidity crosses a threshold value of either chEnvHumidityMoist,
or chEnvHumidityDry, or when the humidity sensor is detected to
be broken or not supported. TRAP-TYPE .1.3.6.1.4.1.52.0.11167 |
boardEnvTempChangesThis trap is generated for each and every time the board
temperature crosses over a threshold value of either
one of the board set thresholds boardEnvTempHot,
boardEnvTempWarm, boardEnvTempCool, or boardEnvTempCold
to another. This trap is also sent when the board temperature
sensor is detected to be broken or not supported. TRAP-TYPE .1.3.6.1.4.1.52.0.11168 |
boardEnvTempRelChangesThis trap is generated for each and every time the board
temperature relative to the chassis ambient temperature
crosses a threshold value of either boardEnvTempRelHot,
or boardEnvTempRelWarm. This trap is also sent when either
temperature sensor located on the board or on the chassis
is detected to be broken or not supported. TRAP-TYPE .1.3.6.1.4.1.52.0.11169 |
boardEnvTempMaxFanRelChangesThis trap is generated for each and every time the board
temperature relative to the chassis ambient temperature
crosses a threshold value of either boardEnvTempMaxFanRelHot,
or boardEnvTempMaxFanRelWarm when all fans in the chassis are
operating at there maximum speed. This trap is also sent when
either temperature sensor located on the board or on the chassis
is detected to be broken or not supported. TRAP-TYPE .1.3.6.1.4.1.52.0.11170 |
chPowerMainVoltageChangesThis trap is generated for each and every time the chassis
main voltage rail deviates and causes the chPowerMainVoltageStatus
to switch state from powerOK(1), overCurrent(2), overVoltage(3),
or underVoltage(4) to another. TRAP-TYPE .1.3.6.1.4.1.52.0.11171 |
chPowerDiagVoltageChangesThis trap is generated for each and every time the chassis
diag voltage deviates and causes the chPowerDiagVoltageStatus
to switch state from powerOK(1), overCurrent(2), overVoltage(3),
or underVoltage(4) to another. TRAP-TYPE .1.3.6.1.4.1.52.0.11172 |
termPowerVoltageChangesThis trap is generated for each and every time the module's
termination unit changes state and causes the termPowerStatus
to switch from any states to either powerOK(1), overVoltage(3), or
underVolatge(4) state. TRAP-TYPE .1.3.6.1.4.1.52.0.11173 |
boardPowerVoltageChangesThis trap is generated for each and every time the module's
power line voltage deviates and causes the boardPowerStatus
to switch from any states to either powerOK(1), overVoltage(4),
or underVoltage(5) state. TRAP-TYPE .1.3.6.1.4.1.52.0.11174 |
termPowerModule1ChangesThis trap is generated for each and every time the module's
front panel button changes state and causes the termPowerModule1Status
to switch state from either one of normal(1), iNBaFault(2),
iNBbFault(3), fault(4), termModuleNotInstalled(5) to another. TRAP-TYPE .1.3.6.1.4.1.52.0.11175 |
termPowerModule2ChangesThis trap is generated for each and every time the module's
front panel button changes state and causes the termPowerModule2Status
to switch state from either one of normal(1), iNBaFault(2),
iNBbFault(3), fault(4), termModuleNotInstalled(5) to another. TRAP-TYPE .1.3.6.1.4.1.52.0.11176 |
chEnvFanChangesThis trap is generated for each and every time the chassis
fan changes over its status from either one value unknown(1),
normal(2), testing(3), slow(4), inoperative(5), or off(6)
to another. TRAP-TYPE .1.3.6.1.4.1.52.0.11177 |
boardPowerCurrentChangesThis trap is generated for each and every time the module's
power line current deviates and causes the boardPowerStatus
to switch from any states to powerOK(1), or overCurrent(3) state. TRAP-TYPE .1.3.6.1.4.1.52.0.11182 |
boardPowerFrontPanelChangesThis trap is generated for each and every time the module's
front panel button state changes, it is caused when the
boardPowerLocalStatus switching state from either one
of resetRequest(1), powerDownRequest(2), powerOnRequest(3),
or normal(4) to another. TRAP-TYPE .1.3.6.1.4.1.52.0.11183 |
boardPowerOperationalChangesThis trap is generated for each and every time the module's
DC-DC converter power supply voltage deviates and causes the
boardPowerOperationalStatus to switch state from powerOn(1),
powerOff(2), reset(3), overVoltage(4), underVoltage(5),
overCurrent(6), overCurrentShutdown(7), temperatureShutdown(8),
remotePowerOff(9), powerConservationShutdown(10), or
frontPanelPowerOff(11) to another. TRAP-TYPE .1.3.6.1.4.1.52.0.11184 |
psEnvTempChangesThis trap is generated for each and every time the power
supply temperature crosses over a threshold value of either
one of the power supply set thresholds psEnvTempHot,
psEnvTempWarm, psEnvTempCool, or psEnvTempCold to another.
This trap is also sent when the power supply temperature
sensor is detected to be broken or not supported. TRAP-TYPE .1.3.6.1.4.1.52.0.11185 |
psEnvFanChangesThis trap is generated for each and every time the power
supply fan changes over its status from either one value
unknown(1), normal(2), testing(3), slow(4), inoperative(5),
or off(6) to another. TRAP-TYPE .1.3.6.1.4.1.52.0.11186 |
psPowerVoltageChangesThis trap is generated for each and every time the module's
power line voltage deviates and causes the psPowerStatus
to switch from any states to either powerOK(1), overVoltage(4),
or underVoltage(5) state. TRAP-TYPE .1.3.6.1.4.1.52.0.11187 |
psPowerCurrentChangesThis trap is generated for each and every time the module's
power line current deviates and causes the psPowerStatus
to switch from any states to powerOK(1), or overCurrent(3) state. TRAP-TYPE .1.3.6.1.4.1.52.0.11188 |
psPowerAdminChangesThis trap is generated for each and every time the power
supply power line changes state from one operational mode
to another switching between powerOn(1) and powerOff(2). TRAP-TYPE .1.3.6.1.4.1.52.0.11189 |
psPowerOperationalChangesThis trap is generated for each and every time the module's
DC-DC converter power supply voltage deviates and causes the
psPowerOperationalStatus to switch state from either one
of powerOn(1), powerOff(2), reset(3), overVoltage(4),
underVoltage(5), overCurrent(6), overCurrentShutdown(7),
temperatureShutdown(8), or remotePowerOff(9) to another. TRAP-TYPE .1.3.6.1.4.1.52.0.11190 |
boardInsertedThis trap is generated when an MMACplus card
is inserted in the chassis. TRAP-TYPE .1.3.6.1.4.1.52.0.11191 |
boardRemovedThis trap is generated when an MMACplus card
is removed from the chassis. TRAP-TYPE .1.3.6.1.4.1.52.0.11192 |
psInsertedThis trap is generated when an MMACplus power supply
is inserted in the chassis. TRAP-TYPE .1.3.6.1.4.1.52.0.11193 |
psRemovedThis trap is generated when an MMACplus power supply
is removed from the chassis. TRAP-TYPE .1.3.6.1.4.1.52.0.11194 |
psRedundantThis trap is generated when an MMACplus power supply
has a redundant power supply TRAP-TYPE .1.3.6.1.4.1.52.0.11195 |
psNotRedundantThis trap is generated when an MMACplus power supply
has no redundant power supply TRAP-TYPE .1.3.6.1.4.1.52.0.11196 |
psNormalThis trap is generated when an MMACplus board is
transitioning to a normal state from a fault state TRAP-TYPE .1.3.6.1.4.1.52.0.11197 |
psFaultThis trap is generated when an MMACplus power supply
is not operational TRAP-TYPE .1.3.6.1.4.1.52.0.11198 |
upsLineFailThis trap is generated in the event of an AC utility
line failure. TRAP-TYPE .1.3.6.1.4.1.52.0.11200 |
upsLineFailRecoveryThis trap is generated when the UPS switches back
to line, and only if the upsLineFail trap was issued
first. TRAP-TYPE .1.3.6.1.4.1.52.0.11201 |
upsLowBatteryThis trap is generated in the event that the UPS's
battery is found to be low. TRAP-TYPE .1.3.6.1.4.1.52.0.11202 |
upsLowBatteryRecoveryThis trap is generated when the UPS's battery has
charged above the low-battery point, and only if the
upsLowBattery trap was issued first. TRAP-TYPE .1.3.6.1.4.1.52.0.11203 |
upsAbnormalConditionThis trap is generated in the event that the UPS
has entered an abnormal condition, such as an
overload or trip on low battery. This trap is also
sent when the UPS is first turned on. TRAP-TYPE .1.3.6.1.4.1.52.0.11204 |
upsAbnormalConditionRecoveryThis trap is generated when the UPS has recovered
from an abnormal condition, and only if the
upsAbnormalCondition trap was issued first. TRAP-TYPE .1.3.6.1.4.1.52.0.11205 |
upsShuttingDownThis trap is generated in the event that the UPS
has been ordered to shut itself, or the load, off
over the serial line. TRAP-TYPE .1.3.6.1.4.1.52.0.11206 |
upsReplaceBatteryThis trap is generated when the UPS's battery test
has determined that a UPS battery is unable to retain
adequate charge. This trap will be generated every
five hours until a new battery test is run or the
UPS is turned off. TRAP-TYPE .1.3.6.1.4.1.52.0.11207 |
upsExtMeasAlarmThis trap is generated when the External Measurement Unit
has detected that an ambient temperature or humidity limit
extreme has been exceeded, or that one of the contact closure
inputs has changed from the selected `normal' state. In
the case of multiple alarms, a trap is generated for every
alarm condition detected. In addition, the trap is sent
every two minutes whenever an alarm condition exists. It
is discontinued when all alarm conditions are reset. This
trap is sent only for alarm states that have been enabled. TRAP-TYPE .1.3.6.1.4.1.52.0.11208 |
nvmpUdefTrapThis trap is generated when a new NVMP trap is sent that
does not have an SNMP counterpart. TRAP-TYPE .1.3.6.1.4.1.52.0.11999 |
activePortInATMRedundancyFailedThis trap will be generated when the active port, on a physical ATM
interface that has redundancy enabled, has failed (become quiet). TRAP-TYPE .1.3.6.1.4.1.52.0.12000 |
aTMRedundantPortActivatedThis trap indicates that a new port has been activated on a
physical ATM interface that has redundancy enabled. This does
not indicate that this port is usable, but that it is being
tested as a possible replacement. TRAP-TYPE .1.3.6.1.4.1.52.0.12001 |
aTMRedundanctPortTestFailedThis trap will be generated when the phyRedundIfTestTOD or the
phyRedundIfPerformTest has tested a port and determined that it
is not usable. The port should be fixed prior to it being needed. TRAP-TYPE .1.3.6.1.4.1.52.0.12002 |
aTMRedundPrimaryPortSkippedThis trap will be generated when redundancy finds that the primary
port as designated be PhyRedundIfPrimaryPort is usable but cannot be
used because PhyRedundIfPrimaryRevert is set to manual (2). This
trap is generated only when redundancy is enabled (PhyRedundIfStatus
is enable (1)) and the active port fails. TRAP-TYPE .1.3.6.1.4.1.52.0.12003 |
atmCTMUpThis trap signifies that the agent has detected
the CTM operational. Connection set maps are allowed
through the switch TRAP-TYPE .1.3.6.1.4.1.52.0.12006 |
atmCTMDownThis trap signifies that the agent has detected
the CTM unoperational. A list of Cross Connect Ids
will be sent indicating connections that need to be removed. TRAP-TYPE .1.3.6.1.4.1.52.0.12007 |
atmVcCrossConnectOperChangeThis trap signifies that the agent has detected
a change in the operational status to down. A list of VC cross
connections will be sent to be remapped. TRAP-TYPE .1.3.6.1.4.1.52.0.12008 |
atmVpCrossConnectOperChangeThis trap signifies that the agent has detected
a change in the operational status to down. A list of VP cross
connections will be sent to be remapped. TRAP-TYPE .1.3.6.1.4.1.52.0.12009 |
atmNeighborSwitchUpThis trap signifies that the agent has detected
a neighbor switch on a port. TRAP-TYPE .1.3.6.1.4.1.52.0.12010 |
atmNeighborSwitchDownThis trap signifies that the agent has detected
a lost neighbor switch on a port. TRAP-TYPE .1.3.6.1.4.1.52.0.12011 |
callFailureSPVC Call Failures. TRAP-TYPE .1.3.6.1.4.1.52.0.12012 |
allocBwHiFwdAllocated bandwidth for this port has exceeded the
allocBwThresholdHiFwd. TRAP-TYPE .1.3.6.1.4.1.52.0.12013 |
allocBwHiRevAllocated bandwidth for this port has exceeded the
allocBwThresholdHiRev. TRAP-TYPE .1.3.6.1.4.1.52.0.12014 |
allocBwLoFwdAllocated bandwidth for this port is below the
allocBwThresholdLoFwd. TRAP-TYPE .1.3.6.1.4.1.52.0.12015 |
allocBwLoRevAllocated bandwidth for this port is below the
allocBwThresholdLoRev. TRAP-TYPE .1.3.6.1.4.1.52.0.12016 |
aggPcrFwdThe total of all the aggregate peak cell rates for the VCs using
this port exceeds the physical bandwidth of the port in the forward
direction. TRAP-TYPE .1.3.6.1.4.1.52.0.12017 |
aggPcrRevThe total of all the aggregate peak cell rates for the VCs using
this port exceeds the physical bandwidth of the port in the reverse
direction. TRAP-TYPE .1.3.6.1.4.1.52.0.12018 |
peakFwdThe peak allocated bandwidth has exceeded the peakBwTholdFwd
value. TRAP-TYPE .1.3.6.1.4.1.52.0.12019 |
peakRevThe peak allocated bandwidth has exceeded the peakBwTholdRev
value. TRAP-TYPE .1.3.6.1.4.1.52.0.12020 |
cbrConnCountTholdHiFwdCount of currently active constant bit rate connections exceeding
the CBRConnectionCountTholdHiFwd threshold. TRAP-TYPE .1.3.6.1.4.1.52.0.12021 |
cbrConnCountTholdHiRevCount of currently active CBR connections exceeding the
CBRConnectionCountTholdHiRev threshold. TRAP-TYPE .1.3.6.1.4.1.52.0.12022 |
cbrConnCountTholdLoFwdCount of currently active CBR connections exceeding the
CBRConnectionCountTholdLoFwd threshold. TRAP-TYPE .1.3.6.1.4.1.52.0.12023 |
cbrConnCountTholdLoRevCount of currently active CBR connections exceeding the
CBRConnectionCountTholdLoRev threshold. TRAP-TYPE .1.3.6.1.4.1.52.0.12024 |
cbrAllocBwTholdHiFwdBandwidth currently allocated which CBR exceeds the
CBRAllocatedBwTholdHiFwd threshold. TRAP-TYPE .1.3.6.1.4.1.52.0.12025 |
cbrAllocBwTholdHiRevBandwidth currently allocated which CBR exceeds the
CBRAllocatedBwTholdHiRev threshold. TRAP-TYPE .1.3.6.1.4.1.52.0.12026 |
cbrAllocBwTholdLoFwdBandwidth currently allocated which CBR exceeds the
CBRAllocatedBwTholdLoFwd threshold. TRAP-TYPE .1.3.6.1.4.1.52.0.12027 |
cbrAllocBwTholdLoRevBandwidth currently allocated which CBR exceeds the
CBRAllocatedBwTholdLoRev threshold. TRAP-TYPE .1.3.6.1.4.1.52.0.12028 |
vbrConnCountTholdHiFwdCount of currently active variable bit rate connections exceeding
the VBRConnectionCountTholdHiFwd threshold. TRAP-TYPE .1.3.6.1.4.1.52.0.12029 |
vbrConnCountTholdHiRevCount of currently active VBR connections exceeding the
VBRConnectionCountTholdHiRev threshold. TRAP-TYPE .1.3.6.1.4.1.52.0.12030 |
vbrConnCountTholdLoFwdCount of currently active VBR connections exceeding the
VBRConnectionCountTholdLoFwd threshold. TRAP-TYPE .1.3.6.1.4.1.52.0.12031 |
vbrConnCountTholdLoRevCount of currently active VBR connections exceeding the
VBRConnectionCountTholdLoRev threshold. TRAP-TYPE .1.3.6.1.4.1.52.0.12032 |
vbrAllocBwTholdHiFwdBandwidth currently allocated which VBR exceeds the
VBRAllocatedBwTholdHiFwd threshold. TRAP-TYPE .1.3.6.1.4.1.52.0.12033 |
vbrAllocBwTholdHiRevBandwidth currently allocated which VBR exceeds the
VBRAllocatedBwTholdHiRev threshold. TRAP-TYPE .1.3.6.1.4.1.52.0.12034 |
vbrAllocBwTholdLoFwdBandwidth currently allocated which VBR exceeds the
VBRAllocatedBwTholdLoFwd threshold. TRAP-TYPE .1.3.6.1.4.1.52.0.12035 |
vbrAllocBwTholdLoRevBandwidth currently allocated which VBR exceeds the
VBRAllocatedBwTholdLoRev threshold. TRAP-TYPE .1.3.6.1.4.1.52.0.12036 |
abrConnCountTholdHiFwdCount of currently active available bit rate connections
exceeding the ABRConnectionCountTholdHiFwd threshold. TRAP-TYPE .1.3.6.1.4.1.52.0.12037 |
abrConnCountTholdHiRevCount of currently active ABR connections exceeding the
ABRConnectionCountTholdHiRev threshold. TRAP-TYPE .1.3.6.1.4.1.52.0.12038 |
abrConnCountTholdLoFwdCount of currently active ABR connections exceeding the
ABRConnectionCountTholdLoFwd threshold. TRAP-TYPE .1.3.6.1.4.1.52.0.12039 |
abrConnCountTholdLoRevCount of currently active ABR connections exceeding the
ABRConnectionCountTholdLoRev threshold. TRAP-TYPE .1.3.6.1.4.1.52.0.12040 |
abrAllocBwTholdHiFwdBandwidth currently allocated which ABR exceeds the
ABRAllocatedBwTholdHiFwd threshold. TRAP-TYPE .1.3.6.1.4.1.52.0.12041 |
abrAllocBwTholdHiRevBandwidth currently allocated which ABR exceeds the
ABRAllocatedBwTholdHiRev threshold. TRAP-TYPE .1.3.6.1.4.1.52.0.12042 |
abrAllocBwTholdLoFwdBandwidth currently allocated which ABR exceeds the
ABRAllocatedBwTholdLoFwd threshold. TRAP-TYPE .1.3.6.1.4.1.52.0.12043 |
abrAllocBwTholdLoRevBandwidth currently allocated which ABR exceeds the
ABRAllocatedBwTholdLoRev threshold. TRAP-TYPE .1.3.6.1.4.1.52.0.12044 |
ubrConnCountTholdHiFwdCount of currently active unavailable bit rate connections
exceeding the UBRConnectionCountTholdHiFwd threshold. TRAP-TYPE .1.3.6.1.4.1.52.0.12045 |
ubrConnCountTholdHiRevCount of currently active UBR connections exceeding the
UBRConnectionCountTholdHiRev threshold. TRAP-TYPE .1.3.6.1.4.1.52.0.12046 |
ubrConnCountTholdLoFwdCount of currently active UBR connections exceeding the
UBRConnectionCountTholdLoFwd threshold. TRAP-TYPE .1.3.6.1.4.1.52.0.12047 |
ubrConnCountTholdLoRevCount of currently active UBR connections exceeding the
UBRConnectionCountTholdLoRev threshold. TRAP-TYPE .1.3.6.1.4.1.52.0.12048 |
ubrAllocBwTholdHiFwdBandwidth currently allocated which UBR exceeds the
UBRAllocatedBwTholdHiFwd threshold. TRAP-TYPE .1.3.6.1.4.1.52.0.12049 |
atmLecStatusThis trap is generated when the operational
state of the LAN Emulation Client has changed. TRAP-TYPE .1.3.6.1.4.1.52.0.12050 |
ubrAllocBwTholdLoFwdBandwidth currently allocated which UBR exceeds the
UBRAllocatedBwTholdLoFwd threshold. TRAP-TYPE .1.3.6.1.4.1.52.0.12051 |
ubrAllocBwTholdLoRevBandwidth currently allocated which UBR exceeds the
UBRAllocatedBwTholdLoRev threshold. TRAP-TYPE .1.3.6.1.4.1.52.0.12052 |
ubrAllocBwTholdHiRevBandwidth currently allocated which UBR exceeds the
UBRAllocatedBwTholdHiRev threshold. TRAP-TYPE .1.3.6.1.4.1.52.0.12053 |
boardOperationalThis trap will be generated when an entity detects
that a module has become operational. TRAP-TYPE .1.3.6.1.4.1.52.0.13000 |
boardNonOperationalThis trap will be generated when an entity detects
that a module is no longer operational. TRAP-TYPE .1.3.6.1.4.1.52.0.13001 |