CTRON-AP3000-MIB
AI MIB Summary
The CTRON-AP3000-MIB module enables read-write SNMP configuration management for Enterasys AP3000 wireless access points under the Enterasys enterprise OID. It provides programmatic access to device-specific operational parameters and settings required for provisioning and maintaining the AP3000 hardware.
This mib module defines a portion of the SNMP enterprise MIBs under Enterasys Networks enterprise OID as an extension to the Enterasys AP3000 MIB.
This Enterasys Networks Proprietary MIB was designed to be used for read-write access to configuration objects in AP3000.
Main OID:
ctronAP3000.1.3.6.1.4.1.52.4.13
361
Objects
Active
Status
3
Dependencies
Imported Objects
Objects
361 total| Object Name |
|---|
cabletron OBJECT IDENTIFIER .1.3.6.1.4.1.52 |
mibs OBJECT IDENTIFIER .1.3.6.1.4.1.52.4 |
ctronAP3000This mib module defines a portion of the SNMP enterprise
MIBs under Enterasys Networks enterprise OID as an extension
to the Enterasys AP3000 MIB.
This Enterasys Networks Proprietary MIB was designed to be
used for read-write access to configuration objects in AP3000. MODULE-IDENTITY .1.3.6.1.4.1.52.4.13 |
comPortMgnt OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.13.1 |
comPortControlThe administrative enable/disable state for
COM Port Control in a System.rw Enumeration .1.3.6.1.4.1.52.4.13.1.1 |
macFilterMgnt OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.13.2 |
macFilterTableTable of status information about
each configured MAC Filtering Entry.deprecated SEQUENCE OF MacFilterEntry .1.3.6.1.4.1.52.4.13.2.1 |
macFilterEntryAn entry in the table, containing information
about configuration of MAC Filter.deprecated MacFilterEntry .1.3.6.1.4.1.52.4.13.2.1.1 |
macFilterIndexFilter index.deprecated Integer32 .1.3.6.1.4.1.52.4.13.2.1.1.1 |
macFilterAddressThis values indicates the MAC address of the
MAC Filter entry.rwdeprecated MacAddress (SNMPv2-TC) .1.3.6.1.4.1.52.4.13.2.1.1.2 |
macFilterAllowedToGoThe administrative allow/deny state for
that specified MAC Filter Entry.rwdeprecated Enumeration .1.3.6.1.4.1.52.4.13.2.1.1.3 |
macFilterOpeStatusThis object indicates the status of this entry.
other(0) - this entry is currently in use but
the conditions under which it will remain
so differ from the following values.
valid(1) - this value to indicate this entry is currently
in used.
invalid(2) - write this value to the corresponding entry,
the whole entry will be removed. Since the order of entry
shall be re-order while it has been deleted. To re-freshed
the whole table is recommended for new index.
create(3) - write this value to indicate that the new MAC address
will be added after next writing MAC address to that new entry.
The adding action will be taken on the index that grater than 1.rwdeprecated Enumeration .1.3.6.1.4.1.52.4.13.2.1.1.4 |
apMacFilterControlThis value indicates the control of the MAC filter setting.rwdeprecated Enumeration .1.3.6.1.4.1.52.4.13.2.2 |
apvMacFilterOperateTableThe Table used to manage the function in
MAC Filter Table. SEQUENCE OF ApvMacFilterOperateEntry .1.3.6.1.4.1.52.4.13.2.3 |
apvMacFilterOperateEntryAn entry in the table, containing information
about configuration in one VAP of the AP. ApvMacFilterOperateEntry .1.3.6.1.4.1.52.4.13.2.3.1 |
apvMacFilterPermissionThis values indicates the Permission on all the active
filter entry for each Vap. The negative permission will
be applied on any inactive entry or any MAC that is not
in the table.rw Enumeration .1.3.6.1.4.1.52.4.13.2.3.1.1 |
apvMacFilterAddressToAddThis values indicates the MAC address to be added to the
local MAC filter table as an active entry for each Vap.rw OCTET STRING .1.3.6.1.4.1.52.4.13.2.3.1.2 |
apvMacFilterTableTable of status information about
each configured MAC Address Filtering Entry. SEQUENCE OF ApvMacFilterEntry .1.3.6.1.4.1.52.4.13.2.4 |
apvMacFilterEntryAn entry in the table, containing information
about configuration in one radio of the AP.
MacFilterEntry is created and managed using
localMACFilterMgnt Table. ApvMacFilterEntry .1.3.6.1.4.1.52.4.13.2.4.1 |
apvMacFilterIndexMAC Filter index in each VAP. Integer32 .1.3.6.1.4.1.52.4.13.2.4.1.1 |
apvMacFilterAddressThis values indicates the MAC address of the
filter entry.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.52.4.13.2.4.1.2 |
apvMacFilterActivityThis value indicates the Activity of the MAC table
entry by the filter permission. If allow(1), the filter
permission will be applied to the MAC address.
If denied(2), the filter permission will not be applied
to the MAC address.
If delete_entry(3), the filter entry will be deleted.rw Enumeration .1.3.6.1.4.1.52.4.13.2.4.1.3 |
qosMgnt OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.13.3 |
qosModeControlThe administrative status and control of the QoS mode for the QoS management.rw Enumeration .1.3.6.1.4.1.52.4.13.3.1 |
qosMACTypeTableTable of status information about
each configured MAC Type Entry for the QoS Management. SEQUENCE OF QosMACTypeEntry .1.3.6.1.4.1.52.4.13.3.2 |
qosMACTypeEntryAn entry in the table, containing information
about configuration MAC Type Entry for the QoS Management. QosMACTypeEntry .1.3.6.1.4.1.52.4.13.3.2.1 |
qosMACTypeIndexQos MAC Type index. Integer32 .1.3.6.1.4.1.52.4.13.3.2.1.1 |
qosMACTypeAddressThis values indicates the MAC address of that specified
index in the entry.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.52.4.13.3.2.1.2 |
qosMACTypePriorityThis values indicates the level of priority of that specified
MAC Address in entry.rw Integer32 .1.3.6.1.4.1.52.4.13.3.2.1.3 |
qosMACTypeOpeStatusThis object indicates the status of this entry.
other(0) - this entry is currently in use but
the conditions under which it will remain
so differ from the following values.
valid(1) - this value to indicate this entry is currently
in used.
invalid(2) - write this value to the corresponding entry,
the whole entry will be removed. Since the order of entry
shall be re-order while it has been deleted. To re-freshed
the whole table is recommended for new index.
create(3) - write this value to indicate that the new MAC address
will be added after next writing MAC address to that new entry.
The adding action will be taken on the index that grater than 1.rw Enumeration .1.3.6.1.4.1.52.4.13.3.2.1.4 |
qosEtherTypeTableTable of status information about
each configured Ether Type Entry for QoS Management. SEQUENCE OF QosEtherTypeEntry .1.3.6.1.4.1.52.4.13.3.3 |
qosEtherTypeEntryAn entry in the table, containing information
about configuration Ether Type for QoS Management. QosEtherTypeEntry .1.3.6.1.4.1.52.4.13.3.3.1 |
qosEtherTypeIndexQos Ether Type index in the table. Integer32 .1.3.6.1.4.1.52.4.13.3.3.1.1 |
qosEtherTypeHexValueThe Hex Value to indicate the type of Ether of that specified
index in the entry.rw OCTET STRING .1.3.6.1.4.1.52.4.13.3.3.1.2 |
qosEtherTypePriorityThis values indicates the level of priority of that specified
MAC Address in entry.rw Integer32 .1.3.6.1.4.1.52.4.13.3.3.1.3 |
qosEtherTypeOpeStatusThis object indicates the status of this entry.
other(0) - this entry is currently in use but
the conditions under which it will remain
so differ from the following values.
valid(1) - this value to indicate this entry is currently
in used.
invalid(2) - write this value to the corresponding entry,
the whole entry will be removed. Since the order of entry
shall be re-order while it has been deleted. To re-freshed
the whole table is recommended for new index.
create(3) - write this value to indicate that the new Ether Value
will be added after next writing Ether Type Value to that new entry.
The adding action will be taken on the index that grater than 1.rw Enumeration .1.3.6.1.4.1.52.4.13.3.3.1.4 |
qosQueueingModeThe administrative control of the QoS Queuing mode for the QoS management.rw Enumeration .1.3.6.1.4.1.52.4.13.3.4 |
qosSVPStatusThe administrative enable/disable state for SVP.rw Enumeration .1.3.6.1.4.1.52.4.13.3.5 |
linkQualityMgnt OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.13.4 |
linkQualityTableTable of status information about
the radio Interface Link Quality Entry. SEQUENCE OF LinkQualityEntry .1.3.6.1.4.1.52.4.13.4.1 |
linkQualityEntryAn entry in the table, containing information
about configuration of the radio Interface Link Quality. LinkQualityEntry .1.3.6.1.4.1.52.4.13.4.1.1 |
linkQualityRadioIndexThis is the value to define the index
of the radio interface. Integer32 .1.3.6.1.4.1.52.4.13.4.1.1.1 |
linkQualityStaIndexThis is value to define the index
of link station. Integer32 .1.3.6.1.4.1.52.4.13.4.1.1.2 |
linkQualityStaMacAddressThis values indicates the MAC address of the
link station.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.52.4.13.4.1.1.3 |
linkQualityStaRssiThis values indicates the percentage RSSI of the
link station.ro Integer32 .1.3.6.1.4.1.52.4.13.4.1.1.4 |
apSnmpMgnt OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.13.5 |
trapControlThe administrative enable/disable state for
SNMP Trap Control in a System.rw Enumeration .1.3.6.1.4.1.52.4.13.5.1 |
trapConfiguration OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.13.5.2 |
trapSysSystemUpThe administrative enable/disable state for
SNMP sysSystemUp trap.rw Enumeration .1.3.6.1.4.1.52.4.13.5.2.1 |
trapSysSystemDownThe administrative enable/disable state for
SNMP sysSystemDown trap.rw Enumeration .1.3.6.1.4.1.52.4.13.5.2.2 |
trapSysRadiusServerChangedThe administrative enable/disable state for
SNMP sysRadiusServerChanged trap.rw Enumeration .1.3.6.1.4.1.52.4.13.5.2.3 |
trapDot11StationAssociationThe administrative enable/disable state for
SNMP dot11StationAssociation trap.rw Enumeration .1.3.6.1.4.1.52.4.13.5.2.4 |
trapDot11StationReAssociationThe administrative enable/disable state for
SNMP dot11StationReAssociation trap.rw Enumeration .1.3.6.1.4.1.52.4.13.5.2.5 |
trapDot11StationAuthenticationThe administrative enable/disable state for
SNMP dot11StationAuthentication trap.rw Enumeration .1.3.6.1.4.1.52.4.13.5.2.6 |
trapDot11StationRequestFailThe administrative enable/disable state for
SNMP dot11StationRequestFail trap.rw Enumeration .1.3.6.1.4.1.52.4.13.5.2.7 |
trapLocalMacAddrAuthFailThe administrative enable/disable state for
SNMP localMacAddrAuthFail trap.rw Enumeration .1.3.6.1.4.1.52.4.13.5.2.9 |
trapLocalMacAddrAuthSuccessThe administrative enable/disable state for
SNMP localMacAddrAuthSuccess trap.rw Enumeration .1.3.6.1.4.1.52.4.13.5.2.10 |
trapDot1xAuthNotInitiatedThe administrative enable/disable state for
SNMP dot1xAuthNotInitiated trap.rw Enumeration .1.3.6.1.4.1.52.4.13.5.2.11 |
trapDot1xAuthSuccessThe administrative enable/disable state for
SNMP dot1xAuthSuccess trap.rw Enumeration .1.3.6.1.4.1.52.4.13.5.2.12 |
trapDot1xAuthFailThe administrative enable/disable state for
SNMP dot1xAuthFail trap.rw Enumeration .1.3.6.1.4.1.52.4.13.5.2.13 |
trapDot1xMacAddrAuthSuccessThe administrative enable/disable state for
SNMP dot1xMacAddrAuthSuccess trap.rw Enumeration .1.3.6.1.4.1.52.4.13.5.2.14 |
trapDot1xMacAddrAuthFailThe administrative enable/disable state for
SNMP dot1xMacAddrAuthFail trap.rw Enumeration .1.3.6.1.4.1.52.4.13.5.2.15 |
trapPppLogonFailThe administrative enable/disable state for
SNMP pppLogonFail trap.rw Enumeration .1.3.6.1.4.1.52.4.13.5.2.16 |
trapIappStationRoamedFromThe administrative enable/disable state for
SNMP iappStationRoamedFrom trap.rw Enumeration .1.3.6.1.4.1.52.4.13.5.2.17 |
trapIappStationRoamedToThe administrative enable/disable state for
SNMP iappStationRoamedFrom trap.rw Enumeration .1.3.6.1.4.1.52.4.13.5.2.18 |
trapIappContextDataSentThe administrative enable/disable state for
SNMP iappContextDataSent trap.rw Enumeration .1.3.6.1.4.1.52.4.13.5.2.19 |
trapSntpServerFailThe administrative enable/disable state for
SNMP sntpServerFail trap.rw Enumeration .1.3.6.1.4.1.52.4.13.5.2.20 |
trapDot11InterfaceAFailThe administrative enable/disable state for
SNMP dot11InterfaceAFail trap.rw Enumeration .1.3.6.1.4.1.52.4.13.5.2.21 |
trapDot11InterfaceGFailThe administrative enable/disable state for
SNMP dot11InterfaceGFail trap.rw Enumeration .1.3.6.1.4.1.52.4.13.5.2.22 |
trapDot11WirelessSTPDetectionThe administrative enable/disable state for
SNMP dot11WirelessSTPDetection trap.rw Enumeration .1.3.6.1.4.1.52.4.13.5.2.23 |
apSnmpTrapDestinationTableTable of descriptive and status information about
configuration of each trap receiving server. SEQUENCE OF ApSnmpTrapDestinationEntry .1.3.6.1.4.1.52.4.13.5.3 |
apSnmpTrapDestinationEntryAn entry in the table, containing information
about configuration of one trap receiving server. ApSnmpTrapDestinationEntry .1.3.6.1.4.1.52.4.13.5.3.1 |
apSnmpTrapDestinationIndexIndex of the Trap Destination Table. INTEGER .1.3.6.1.4.1.52.4.13.5.3.1.1 |
apSnmpTrapDestinationCommunityThe SNMP Trap Communityrw DisplayString .1.3.6.1.4.1.52.4.13.5.3.1.2 |
apSnmpTrapDestinationIPThe IP address of the trap receiving server.rw IpAddress .1.3.6.1.4.1.52.4.13.5.3.1.3 |
apSnmpTrapDestinationStateThis value indicates whether the trap receiving server is enabled.rw Enumeration .1.3.6.1.4.1.52.4.13.5.3.1.4 |
apSnmpCommunityReadOnlyThe SNMP Read Only Community. The value if read,
will only show ******.rw DisplayString .1.3.6.1.4.1.52.4.13.5.4 |
apSnmpCommunityReadWriteThe SNMP Read Write Community. The value if read,
will only show *****.rw DisplayString .1.3.6.1.4.1.52.4.13.5.5 |
apSnmpVersionFilterTo set the version-filter of SNMP.rw Enumeration .1.3.6.1.4.1.52.4.13.5.6 |
sysEntity OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.13.6 |
swHardwareVerHardware version of the main board.ro DisplayString .1.3.6.1.4.1.52.4.13.6.1 |
swBootRomVerBoot ROM code version of the main board.ro DisplayString .1.3.6.1.4.1.52.4.13.6.2 |
swOpCodeVerOperation code version of the main board.ro DisplayString .1.3.6.1.4.1.52.4.13.6.3 |
swSerialNumberSerial Number of the Access Point.ro DisplayString .1.3.6.1.4.1.52.4.13.6.4 |
swProductNameThe Product Name of the Access Point.ro DisplayString .1.3.6.1.4.1.52.4.13.6.5 |
swCountrySettingThe current CountryCode Setting of the Access Point.ro DisplayString .1.3.6.1.4.1.52.4.13.6.6 |
apSecurityMgnt OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.13.7 |
apRadioSecurityTableTable of descriptive and status information about
configuration of each radio in terms of security settings. SEQUENCE OF ApRadioSecurityEntry .1.3.6.1.4.1.52.4.13.7.1 |
apRadioSecurityEntryAn entry in the table, containing information
about configuration of one radio of the AP. ApRadioSecurityEntry .1.3.6.1.4.1.52.4.13.7.1.1 |
apRadioSecurityIndexRadio Index for security settings. Integer32 .1.3.6.1.4.1.52.4.13.7.1.1.1 |
apRadioSecurityWEPAuthTypeThis value indicates the type of WEP authentication in use for this radio interface.
opensystem(0) Set authentication open
sharedkey(1) Set authentication shared
wpa(2) Set WPA Mode
wpapsk(3) Set WPA-PSK Mode
wpa-wpa2-mixed(4) Set WPA-WPA2-Mixed Mode
wpawpa2pskmixed(5) Set WPA-WPA2 PSK Mixed Mode
wpa2(6) Set WPA2 Mode
wpa2psk(7) Set WPA2-PSK Moderw Enumeration .1.3.6.1.4.1.52.4.13.7.1.1.2 |
apRadioSecuritySharedKeyLenThis value indicates the shared key length for this radio interface.ro Enumeration .1.3.6.1.4.1.52.4.13.7.1.1.3 |
apRadioSecurityWPAModeThis value indicates the state of WPA for this radio interface.rw Enumeration .1.3.6.1.4.1.52.4.13.7.1.1.4 |
apRadioSecurityWPAKeyTypeThis value indicates the type of WPA Key Management in use for this radio interface.rw Enumeration .1.3.6.1.4.1.52.4.13.7.1.1.5 |
apRadioSecurityWPACipherThis value indicates the type of WPA Cipher in use for this radio interface.rwobsolete Enumeration .1.3.6.1.4.1.52.4.13.7.1.1.6 |
apRadioSecurityWPAPSKTypeThis value indicates the type of WPA Pre Shared Key in use for this radio interface.rw Enumeration .1.3.6.1.4.1.52.4.13.7.1.1.7 |
apRadioSecurityWPAPSKThis value indicates WPA Pre Shared Key in use for this radio interface.rw DisplayString .1.3.6.1.4.1.52.4.13.7.1.1.8 |
apRadioSecurityWEPKeyTypeThis value indicates the type of WEP Key in use for this radio interface.rw Enumeration .1.3.6.1.4.1.52.4.13.7.1.1.9 |
apRadioSecurityWEPEnabledThis value indicates whether WEP is enabled.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.52.4.13.7.1.1.10 |
apRadioSecurityWPACipherSuiteThis value indicates the type of WPA Cipher Suite in use for this radio interface.rw Enumeration .1.3.6.1.4.1.52.4.13.7.1.1.11 |
apRadioApSecurityWPAPreAuthenticationWhether Pre-Authentication is enabled.rw Enumeration .1.3.6.1.4.1.52.4.13.7.1.1.12 |
apRadioApSecurityWPAPmksaLifetimeThe number (in minutes) for Pmksa-Lifetime.rw INTEGER .1.3.6.1.4.1.52.4.13.7.1.1.13 |
apSecuritySsh OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.13.7.2 |
apSecuritySshServerEnabledThis value indicates whether SSH server is enabled.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.52.4.13.7.2.1 |
apSecuritySshServerPortThis value indicates SSH server's port number.rw Integer32 .1.3.6.1.4.1.52.4.13.7.2.2 |
apSecuritySshTelnetServerEnabledThis value indicates whether telnet server is enabled.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.52.4.13.7.2.3 |
apRadioInterfaceMgnt OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.13.8 |
enterpriseApRadioTableTable of descriptive and status information about
configuration of each radio. SEQUENCE OF EnterpriseApRadioEntry .1.3.6.1.4.1.52.4.13.8.2 |
enterpriseApRadioEntryAn entry in the table, containing information
about configuration of one radio of the AP. EnterpriseApRadioEntry .1.3.6.1.4.1.52.4.13.8.2.1 |
enterpriseApRadioIndexRadio Index for configuration. Integer32 .1.3.6.1.4.1.52.4.13.8.2.1.1 |
enterpriseApRadioAutoChannelThis value indicates whether auto channel selection is enabled or not
for this radio interfacerw Enumeration .1.3.6.1.4.1.52.4.13.8.2.1.2 |
enterpriseApRadioTransmitPowerThis value indicates the transmit power for this radio interface.rw Enumeration .1.3.6.1.4.1.52.4.13.8.2.1.3 |
enterpriseApRadioTurboModeThis value indicates whether turbo mode is enabled for this radio interface.rw Enumeration .1.3.6.1.4.1.52.4.13.8.2.1.4 |
enterpriseApRadioDataRateThis value indicates the data rate for this radio interface.
Radio interface A operates at 6, 9, 12, 18, 24, 36, 48, 54.
Radio interface G operates all listed data rates. The auto
setting will attempt to set the best data rate for the interfacerw Enumeration .1.3.6.1.4.1.52.4.13.8.2.1.5 |
enterpriseApRadioGModeThis value indicates the radio mode for the 802.11g radio.
This setting is only valid for the 802.11g interface.rw Enumeration .1.3.6.1.4.1.52.4.13.8.2.1.6 |
enterpriseApRadioAntennaModeThis value indicates the antenna mode in use for the G-radio.
The values are interpreted as follows:
both(1) means use both built-in antennas,
left(2) means use left side.
right(3) means use right side.
invalid(4) means not support.
This setting is only valid for the 802.11g interface.rw Enumeration .1.3.6.1.4.1.52.4.13.8.2.1.7 |
rogueApStateThis value is used to enable/disable Rogue Ap Detection for
this radio interface.rw Enumeration .1.3.6.1.4.1.52.4.13.8.2.1.8 |
rogueApIntervalHow often to scan for Rogue Aps. The interval in minutes, with default
of 720(minutes).rw INTEGER .1.3.6.1.4.1.52.4.13.8.2.1.9 |
rogueApDurationHow long to scan each channel (in milliseconds). A longer duration will yield more
complete results. A shorter duration will allow clients a better chance
of remaining connected. Default value is 350(milliseconds).rw INTEGER .1.3.6.1.4.1.52.4.13.8.2.1.10 |
rogueApScanNowWhen writing the value to enable, the AP will trigger the Rouge AP scan function.
The value will always return disable(2).rw Enumeration .1.3.6.1.4.1.52.4.13.8.2.1.11 |
enterpriseApRadioAntennaModeControlThis value indicates which antenna is in use for the radio Interface.
The values are interpreted as follows:
fixed(1) specify to use built-in antennas,
external(2) specify to use one external antenna.ro Enumeration .1.3.6.1.4.1.52.4.13.8.2.1.12 |
enterpriseApRadioFixedAntennaTypeThis value indicates which antenna type is in use
as the fixed antenna is selected.rw Enumeration .1.3.6.1.4.1.52.4.13.8.2.1.13 |
enterpriseApRadioAntennaIDThis value indicates which antenna ID will be in use for the radio Interface.rw INTEGER .1.3.6.1.4.1.52.4.13.8.2.1.14 |
enterpriseApRadioMulticastDataRateThis value indicates the data rate for mc/bc packets from this
radio interface. sixMbps(6), nineMbps(9), twelveMbps(12), eighteenMbps(18),
twentyFourMbps(24), thirtySixMbps(36), fortyEightMbps(48), and fiftyFourMbps(54)
are for 11a and g-only mode. The default for b-only and b+g mode is
oneMbps(1), twoMbps(2), fiveAndHalfMbps(5) and elevenMbps(11).rw Enumeration .1.3.6.1.4.1.52.4.13.8.2.1.15 |
enterpriseApRadioAutoDataRateThis value indicates whether automated data rate is enabled or not
for this radio interfacerw Enumeration .1.3.6.1.4.1.52.4.13.8.2.1.16 |
enterpriseApRadioPreambleThis value indicates the preamble length of 11g.
The values are interpreted as follows:
long(1) sets the preamble length to long.
short(2) sets the preamble length to short.
invalid(3) means not support.
This setting is only valid for the 802.11g interface.rw Enumeration .1.3.6.1.4.1.52.4.13.8.2.1.17 |
enterpriseApRadioSWRetryModeThis value indicates whether SW retty mode is enabled or not
for this radio interfacerw Enumeration .1.3.6.1.4.1.52.4.13.8.2.1.18 |
enterpriseApVapRadioTableTable of descriptive and status information about
configuration of each Vap radio. SEQUENCE OF EnterpriseApVapRadioEntry .1.3.6.1.4.1.52.4.13.8.3 |
enterpriseApVapRadioEntryAn entry in the table, containing information
about configuration of one Vap radio of the AP. EnterpriseApVapRadioEntry .1.3.6.1.4.1.52.4.13.8.3.1 |
enterpriseApVapRadioIndexRadio Index for configuration. Integer32 .1.3.6.1.4.1.52.4.13.8.3.1.1 |
enterpriseApVapRadioStateThis value indicates the state of the radio interface.rw Enumeration .1.3.6.1.4.1.52.4.13.8.3.1.2 |
enterpriseApVapRadioSecureAccessThis value indicates whether secure access is enabled for this radio interface.rw Enumeration .1.3.6.1.4.1.52.4.13.8.3.1.3 |
enterpriseApVapRadioMaxAssocThis value indicates the max number of clients allowed on this radio interface.rw INTEGER .1.3.6.1.4.1.52.4.13.8.3.1.4 |
enterpriseApVapRadioTransmitKeyThis value indicates default transmit key in use for this radio interface.rw INTEGER .1.3.6.1.4.1.52.4.13.8.3.1.5 |
enterpriseApVapRadioDescriptionThis value indicates the description for this radio interface.rw DisplayString .1.3.6.1.4.1.52.4.13.8.3.1.6 |
enterpriseApVapRadioDefefaultPriorityThis values indicates the level of default priority of that specified
VAP in entry.rw Integer32 .1.3.6.1.4.1.52.4.13.8.3.1.7 |
enterpriseApRadioWdsTableTable of configuration information for Wds for each
Radio interface. SEQUENCE OF EnterpriseApRadioWdsEntry .1.3.6.1.4.1.52.4.13.8.4 |
enterpriseApRadioWdsEntryAn entry in the table, containing information
about configuration of peer Bridging
for one radio of the AP. The table is indexed by radio
Index (corresponding to enterpriseApRadioTable). The table does not contain the radio index as
a member of the table. EnterpriseApRadioWdsEntry .1.3.6.1.4.1.52.4.13.8.4.1 |
wdsApRoleThis value indicates the role of the Ap for this radio,
roleAp(1): AP operation.
roleBridgeMaster(2): Root-Bridge mode.
roleBridge(3): Bridge Mode.rw Enumeration .1.3.6.1.4.1.52.4.13.8.4.1.1 |
wdsApAckTimeoutThis value indicates the WDS Ack timeout for this radio in us,
and the following values can be set to the system:
0 Set wireless Ack Timeout as system default
20 0 to 1 miles: Ack timeout is 20 us
40 1 to 3 miles: Ack timeout is 40 us
75 3 to 6 miles: Ack timeout is 75 us
115 6 to 10 miles: Ack timeout is 115 usrw INTEGER .1.3.6.1.4.1.52.4.13.8.4.1.2 |
enterpriseApRadioWdsPeerTableTable of configuration information for Wds Peers for each
Radio interface. SEQUENCE OF EnterpriseApRadioWdsPeerEntry .1.3.6.1.4.1.52.4.13.8.5 |
enterpriseApRadioWdsPeerEntryAn entry in the table, containing information
about configuration of peer Bridging
for one radio of the AP. The table is indexed by radio
Index (corresponding to enterpriseApRadioTable) and the peer
index (Up to 8). The table does not contain the radio index as
a member of the table. EnterpriseApRadioWdsPeerEntry .1.3.6.1.4.1.52.4.13.8.5.1 |
wdsPeerIndexPeer Index for the radio interface. Integer32 .1.3.6.1.4.1.52.4.13.8.5.1.1 |
wdsPeerBssidThe BSSID for this peer.rw DisplayString .1.3.6.1.4.1.52.4.13.8.5.1.2 |
wdsPeerRSSIThis value indicates the RSSI value of the WDS peer link.ro Integer32 .1.3.6.1.4.1.52.4.13.8.5.1.3 |
enterpriseApRadioWEPKeysTableConceptual table for WEP default keys. SEQUENCE OF EnterpriseApRadioWEPKeysEntry .1.3.6.1.4.1.52.4.13.8.6 |
enterpriseApRadioWEPKeysEntryAn Entry (conceptual row) in the WEP Default Keys Table.
A collection of objects containing information used to
determine if a WEPkey as been defined and if so, the
value of the WEPkey. EnterpriseApRadioWEPKeysEntry .1.3.6.1.4.1.52.4.13.8.6.1 |
enterpriseApRadioWEPKeysIndexWEP Key Index for the radio interface. INTEGER .1.3.6.1.4.1.52.4.13.8.6.1.1 |
enterpriseApRadioWEPKeyTypestatus of the WEP Key typero Enumeration .1.3.6.1.4.1.52.4.13.8.6.1.2 |
enterpriseApRadioWEPKeyLengthstatus of the WEP Key Length.ro Enumeration .1.3.6.1.4.1.52.4.13.8.6.1.3 |
enterpriseApRadioAvAntennaListTableConceptual table for Available Antenna List used in the Radio. SEQUENCE OF EnterpriseApRadioAvAntennaListEntry .1.3.6.1.4.1.52.4.13.8.7 |
enterpriseApRadioAvAntennaListEntryAn Entry (conceptual row) in the Antenna List Table.
A collection of objects containing information used to
show if an Antenna as been defined and if so, the
value of the antenna Id. EnterpriseApRadioAvAntennaListEntry .1.3.6.1.4.1.52.4.13.8.7.1 |
enterpriseApRadioAvAntennaIndexAvailable Antenna List Index for the radio interface. INTEGER .1.3.6.1.4.1.52.4.13.8.7.1.1 |
enterpriseApRadioAvAntennaIdAvailable antenna Id in the entry.ro INTEGER .1.3.6.1.4.1.52.4.13.8.7.1.2 |
enterpriseApRadioAvAntennaDescThe description of the antenna ID.ro DisplayString .1.3.6.1.4.1.52.4.13.8.7.1.3 |
enterpriseApRadioAvChannelListTableConceptual table for Available Channel List used in the Radio. SEQUENCE OF EnterpriseApRadioAvChannelListEntry .1.3.6.1.4.1.52.4.13.8.8 |
enterpriseApRadioAvChannelListEntryAn Entry (conceptual row) in the Channel List Table.
A collection of objects containing information used to
show if a Channel No. as been defined and if so, the
value of the Channel No. EnterpriseApRadioAvChannelListEntry .1.3.6.1.4.1.52.4.13.8.8.1 |
enterpriseApRadioAvChannelIndexChannel List Index for the radio interface. INTEGER .1.3.6.1.4.1.52.4.13.8.8.1.1 |
enterpriseApRadioAvChannelNoAvailable channel number in the entryro INTEGER .1.3.6.1.4.1.52.4.13.8.8.1.2 |
apEtherInterfaceMgnt OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.13.9 |
apEtherNetConfig OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.13.9.1 |
netConfigIPAddressThe IP address of this Net interface. The default value
for this object is 0.0.0.0. If either the netConfigIPAddress
or netConfigSubnetMask are 0.0.0.0, then when the device
boots, it may use DHCP to try to figure out what these
values should be. If DHCP fails, before the device
can talk on the network, this value must be configured
(e.g., through a terminal attached to the device).rw IpAddress .1.3.6.1.4.1.52.4.13.9.1.1 |
netConfigSubnetMaskThe subnet mask of this Net interface. The default value
for this object is 0.0.0.0. If either the netConfigIPAddress
or netConfigSubnetMask are 0.0.0.0, then when the device
boots, it may use DHCP to try to figure out what these
values should be. If DHCP fails, before the device
can talk on the network, this value must be configured
(e.g., through a terminal attached to the device).rw IpAddress .1.3.6.1.4.1.52.4.13.9.1.2 |
netConfigDefaultGatewayThe IP Address of the default gateway. If this value is
undefined or unknown, it shall have the value 0.0.0.0.rw IpAddress .1.3.6.1.4.1.52.4.13.9.1.3 |
netConfigHttpStateWhether HTTP is enabled.rw Enumeration .1.3.6.1.4.1.52.4.13.9.1.4 |
netConfigHttpPortThe port number for HTTP.rw INTEGER .1.3.6.1.4.1.52.4.13.9.1.5 |
netConfigHttpsStateWhether Secure HTTP is enabled.rw Enumeration .1.3.6.1.4.1.52.4.13.9.1.6 |
netConfigHttpsPortThe port number for Secure HTTP.rw INTEGER .1.3.6.1.4.1.52.4.13.9.1.7 |
netConfigDHCPStateWhether DHCP is enabled.rw Enumeration .1.3.6.1.4.1.52.4.13.9.1.8 |
apFilterControlMgnt OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.13.10 |
apFilterControlBridgeThis value indicates the local bridge filter setting.rw Enumeration .1.3.6.1.4.1.52.4.13.10.1 |
enterpriseApFilterControlAPManageThis value indicates the AP management filter setting.rw Enumeration .1.3.6.1.4.1.52.4.13.10.2 |
enterpriseApFilterControlEthernetThis value indicates the ethernet filter setting.rw Enumeration .1.3.6.1.4.1.52.4.13.10.3 |
enterpriseApFilterProtocolTableTable of descriptive and status information about
configuration of the filter protocol table. SEQUENCE OF EnterpriseApFilterProtocolEntry .1.3.6.1.4.1.52.4.13.10.4 |
enterpriseApFilterProtocolEntryAn entry in the filter protocol table, containing information
about configuration of one filter table entry. EnterpriseApFilterProtocolEntry .1.3.6.1.4.1.52.4.13.10.4.1 |
enterpriseApFilterProtocolIndexIndex of the Protocol Filters. Integer32 .1.3.6.1.4.1.52.4.13.10.4.1.1 |
enterpriseApFilterProtocolNameThis value indicates the name of the protocol filter. One of
the following:
Aironet_DDP, Appletalk_ARP, ARP, Banyan, Berkeley_Trailer_Negotiation,
CDP, DEC_LAT, DEC_MOP, DEC_MOP_Dump_Load, DEC_XNS, EAPOL,
Enet_Config_Test, Ethertalk, IP, LAN_Test, NetBEUI, Novell_IPX(new),
Novell_IPX(old), RARP, Telxon_TXP, X.25_Level3ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.52.4.13.10.4.1.2 |
enterpriseApFilterProtocolISODesignatorThis value indicates the name of the protocol filter.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.52.4.13.10.4.1.3 |
enterpriseApFilterProtocolStateThis value indicates whether the protocol filter is enabled.rw Enumeration .1.3.6.1.4.1.52.4.13.10.4.1.4 |
apvGlobalIBSSRelayModeThis value indicates the setting of the global IBSS Relay mode among the VAPs.
In Per-VAP Mode enable, the traffic between the VAPs should be blocked.
In Al-VAP Mode enable, the traffic between should not be blocked.rw Enumeration .1.3.6.1.4.1.52.4.13.10.5 |
apvFilterControlTableTable of the control and status information about
configuration of the filter Control for each Vap. SEQUENCE OF ApvFilterControlEntry .1.3.6.1.4.1.52.4.13.10.6 |
apvFilterControlEntryAn entry in the table, containing information
about configuration of the filter for each Vap of the AP. ApvFilterControlEntry .1.3.6.1.4.1.52.4.13.10.6.1 |
apvFilterControlIndexIndex of the configuration. Integer32 .1.3.6.1.4.1.52.4.13.10.6.1.1 |
apvIBSSFilterControlThis value indicates the local bridge filter(IBSS Relay Filter) setting.rw Enumeration .1.3.6.1.4.1.52.4.13.10.6.1.2 |
apvAPManageFilterControlThis value indicates the AP management filter setting.rw Enumeration .1.3.6.1.4.1.52.4.13.10.6.1.3 |
apVLANMgnt OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.13.11 |
apVLANMgntNativeIdThis value indicates the native VLAN Id.rw INTEGER .1.3.6.1.4.1.52.4.13.11.1 |
apVLANMgntStateThis value indicates whether VLANs are enabled or disabled.ro Enumeration .1.3.6.1.4.1.52.4.13.11.2 |
apVLANMgntStateNextBootThis value indicates the VLANs state for the next reset.rw Enumeration .1.3.6.1.4.1.52.4.13.11.3 |
apNativeVlanTableTable used to manage the Vlans for each
wireless interface. SEQUENCE OF ApNativeVlanEntry .1.3.6.1.4.1.52.4.13.11.6 |
apNativeVlanEntryAn entry in the table, containing information
about VLAN configuration of one wireless interface. ApNativeVlanEntry .1.3.6.1.4.1.52.4.13.11.6.1 |
apNativeVlanIfIndexInterface Index of the wireless interface for which
the VLAN is assigned to. Integer32 .1.3.6.1.4.1.52.4.13.11.6.1.1 |
apNativeVlanSsidNumberAssociated Number for Service Set Id (SSID) of the
wireless interface for which the VLAN is assigned to.
Note: This is for future support of multiple SSIDs
per radio interface. Integer32 .1.3.6.1.4.1.52.4.13.11.6.1.2 |
apNativeVlanVlanIdThis value indicates the native VLAN Id of the wireless interface associated
with the if index and the SSID number(if it is not 0).rw Integer32 .1.3.6.1.4.1.52.4.13.11.6.1.3 |
apNativeVlanStateThis value indicates the Native VLANs state.rw Enumeration .1.3.6.1.4.1.52.4.13.11.6.1.4 |
apVLANMgntEtherUntaggedVlanIdThis value indicates the Untagged VlanID for Ether Interface.rw Integer32 .1.3.6.1.4.1.52.4.13.11.7 |
apAuthenticationMgnt OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.13.12 |
apAuthenticationSetupEntry OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.13.12.1 |
ap8021xStateThis attribute indicates that the Enterprise the state
of the 802.1X authentication algorithm.rw Enumeration .1.3.6.1.4.1.52.4.13.12.1.1 |
ap8021xBroadcastKeyRefreshRateThe number (in minutes) between changing the broadcast key for
802.1X and WPA clientsrw INTEGER .1.3.6.1.4.1.52.4.13.12.1.2 |
ap8021xSessionKeyRefreshRateThe number (in minutes) between changing session keys for
802.1X and WPA clientsrw INTEGER .1.3.6.1.4.1.52.4.13.12.1.3 |
ap8021xReauthenticationTimeoutThe number (in minutes) between forcing 802.1X clients to
reauthenticaterw INTEGER .1.3.6.1.4.1.52.4.13.12.1.4 |
apAuthenticationModeThis value indicates the type of MAC authentication or RADIUS authentication in use,
or not in use.rw Enumeration .1.3.6.1.4.1.52.4.13.12.1.5 |
apAuthenticationServerTableTable of descriptive and status information about
configuration of each authentication server. SEQUENCE OF ApAuthenticationServerEntry .1.3.6.1.4.1.52.4.13.12.2 |
apAuthenticationServerEntryAn entry in the table, containing information
about configuration of one authentication server of the AP. ApAuthenticationServerEntry .1.3.6.1.4.1.52.4.13.12.2.1 |
apAuthenticationServerIndexIndex of the Authentication Server Integer32 .1.3.6.1.4.1.52.4.13.12.2.1.1 |
apAuthenticationServerThis value indicates the IP address or host name of the authentication server.rw IpAddress SYNTAX DisplayString .1.3.6.1.4.1.52.4.13.12.2.1.2 |
apAuthenticationPortThis value indicates the UDP Port used by the authentication server.rw INTEGER .1.3.6.1.4.1.52.4.13.12.2.1.3 |
apAuthenticationKeyThis value indicates the shared key used by the authentication server.rw DisplayString .1.3.6.1.4.1.52.4.13.12.2.1.4 |
apAuthenticationRetransmitThis value indicates the retransmit timer length used by the
authentication server.rw INTEGER .1.3.6.1.4.1.52.4.13.12.2.1.5 |
apAuthenticationTimeoutThis value indicates the Timeout value(sec) used by the
authentication server.rw INTEGER .1.3.6.1.4.1.52.4.13.12.2.1.6 |
apAuthenticationAcctPortUDP Accounting Port. The valid range is from
1024-65535. A value of 0 means accounting is disabled.rw INTEGER .1.3.6.1.4.1.52.4.13.12.2.1.7 |
apAuthenticationAcctInterimUpdateThe interval between sending accounting
updates.rw INTEGER .1.3.6.1.4.1.52.4.13.12.2.1.8 |
apAuthenticationAcctStateThis value indicates whether the Accounting Server is enabled.rw Enumeration .1.3.6.1.4.1.52.4.13.12.2.1.9 |
apAuthenticationSupplicantTableTable of descriptive and status information about
configuration of supplicant SEQUENCE OF ApAuthenticationSupplicantEntry .1.3.6.1.4.1.52.4.13.12.3 |
apAuthenticationSupplicantEntryAn entry in the table, containing information
about configuration of one supplicant. ApAuthenticationSupplicantEntry .1.3.6.1.4.1.52.4.13.12.3.1 |
ap8021xSuppIndexIndex of the interface for which this supplicant is
running. Currently only the ethernet interface. Integer32 .1.3.6.1.4.1.52.4.13.12.3.1.1 |
ap8021xSuppStateThis object is used to enable or disable the 802.1X supplicant.rw Enumeration .1.3.6.1.4.1.52.4.13.12.3.1.2 |
ap8021xSuppUserThis value indicates the username for supplicant. If value is
configured, will display ****. Else will display EMPTY.rw DisplayString .1.3.6.1.4.1.52.4.13.12.3.1.3 |
ap8021xSuppPasswdThis value indicates the password for supplicant. If value is
configured, will display ****. Else will display EMPTY.rw DisplayString .1.3.6.1.4.1.52.4.13.12.3.1.4 |
apvAuthenticationSetupTableTable of descriptive and status information about
configuration of 8021x for each Vap. SEQUENCE OF ApvAuthenticationSetupEntry .1.3.6.1.4.1.52.4.13.12.4 |
apvAuthenticationSetupEntryAn entry in the table, containing information
about configuration of 8021x for each Vap of the AP. ApvAuthenticationSetupEntry .1.3.6.1.4.1.52.4.13.12.4.1 |
apv8021xIndexIndex for configuration. Integer32 .1.3.6.1.4.1.52.4.13.12.4.1.1 |
apv8021xStateThis attribute indicates that the Enterprise the state
of the 802.1X authentication algorithm.rw Enumeration .1.3.6.1.4.1.52.4.13.12.4.1.2 |
apv8021xBroadcastKeyRefreshRateThe number (in minutes) between changing the broadcast key for
802.1X and WPA clientsrw INTEGER .1.3.6.1.4.1.52.4.13.12.4.1.3 |
apv8021xSessionKeyRefreshRateThe number (in minutes) between changing history keys for
802.1X and WPA clientsrw INTEGER .1.3.6.1.4.1.52.4.13.12.4.1.4 |
apv8021xReauthenticationTimeoutThe number (in minutes) between forcing 802.1X clients to
reauthenticaterw INTEGER .1.3.6.1.4.1.52.4.13.12.4.1.5 |
apvMACAuthenticationModeThis value indicates the mode of MAC authentication in use.rw Enumeration .1.3.6.1.4.1.52.4.13.12.4.1.6 |
apvMACAuthenticationTimeoutThe number (in minutes) between forcing RADIUS MAC to authenticate.rw INTEGER .1.3.6.1.4.1.52.4.13.12.4.1.7 |
apvMACAuthenticationPasswdThis value indicates the password for MAC RADIUS Authentication. If value is
configured, will display ****. Else will display EMPTY.rw DisplayString .1.3.6.1.4.1.52.4.13.12.4.1.8 |
apWStationSessionMgnt OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.13.13 |
apWStationSessionTableThis table list all sessions (wireless stations) status SEQUENCE OF ApWStationSessionEntry .1.3.6.1.4.1.52.4.13.13.1 |
apWStationSessionEntryAn entry in the table, containing information
about status and statistics of the wireless station. ApWStationSessionEntry .1.3.6.1.4.1.52.4.13.13.1.1 |
apWStationSessionIfIndexInterface index for the radio this session is associated
with. Integer32 .1.3.6.1.4.1.52.4.13.13.1.1.1 |
apWStationSessionStationAddresThe unique MAC Address of the station for this session. MacAddress (SNMPv2-TC) .1.3.6.1.4.1.52.4.13.13.1.1.2 |
apWStationSessionAuthenticatedWhether the session is authenticated or not.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.52.4.13.13.1.1.3 |
apWStationSessionAssociatedWhether the session is associated or not. It is rare case that
not associated stations show up in the table.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.52.4.13.13.1.1.4 |
apWStationSessionIsForwardingWhether the AP is forwarding the client station traffic (higher level authentication)ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.52.4.13.13.1.1.5 |
apWStationSessionKeyTypeThe encryption key type used by the station. Note that wpa-wep is not supportedro Enumeration .1.3.6.1.4.1.52.4.13.13.1.1.6 |
apWStationSessionAssociationIdThe internal association identify numberro Integer32 .1.3.6.1.4.1.52.4.13.13.1.1.7 |
apWStationSessionLastAuthenticatedTimeThis is the time in hundredths of a second last time the client
is authenticated. Note that a session may be authenticated multiple times.
The value is related to the system startupro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.52.4.13.13.1.1.8 |
apWStationSessionAssociatedTimeThis is the time in hundredths of a second since the client
associated. The value is related to the system startupro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.52.4.13.13.1.1.9 |
apWStationSessionLastAssociatedTimeThis is the time in hundredths of a second when the client
associated in last session. The value is related to the system startupro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.52.4.13.13.1.1.10 |
apWStationSessionLastDisassociatedTimeThis is the time in hundredths of a second when the client
disassociated in last session. The value is related to the system startupro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.52.4.13.13.1.1.11 |
apWStationSessionTxPacketCountThis is the number of packets transmitted from the client to the AP. It includes
data, control and management packets.ro Counter32 .1.3.6.1.4.1.52.4.13.13.1.1.12 |
apWStationSessionRxPacketCountThis is the number of unicast packets transmitted from the AP to the client.
It includes data, control and management packets.ro Counter32 .1.3.6.1.4.1.52.4.13.13.1.1.13 |
apWStationSessionTxByteCountThis is the number of bytes transmitted from the client to the AP. It
includes the bytes of data, control and management packets.ro Counter32 .1.3.6.1.4.1.52.4.13.13.1.1.14 |
apWStationSessionRxByteCountThis is the number of unicast bytes transmitted from the AP to
the client. It includes the bytes of data, control and management
packets.ro Counter32 .1.3.6.1.4.1.52.4.13.13.1.1.15 |
apWStationSessionVlanIDThe current VLAN Id used by the station.ro INTEGER .1.3.6.1.4.1.52.4.13.13.1.1.16 |
apRogueApMgnt OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.13.14 |
rogueApDetectionTableTable of each AP that has been detected. SEQUENCE OF RogueApDetectionEntry .1.3.6.1.4.1.52.4.13.14.1 |
rogueApDetectionEntryAn entry in the table, containing information
about any AP detected. RogueApDetectionEntry .1.3.6.1.4.1.52.4.13.14.1.1 |
rogueApIndexMonotonically increasing index. INTEGER .1.3.6.1.4.1.52.4.13.14.1.1.1 |
rogueApBssidThe AP BSSIDro DisplayString .1.3.6.1.4.1.52.4.13.14.1.1.2 |
rogueApSsidThe AP SSIDro DisplayString .1.3.6.1.4.1.52.4.13.14.1.1.3 |
rogueApPortNumberInterface index for the radio.ro Integer32 .1.3.6.1.4.1.52.4.13.14.1.1.4 |
rogueApChannelNumberChannel where Ap detected.ro Integer32 .1.3.6.1.4.1.52.4.13.14.1.1.5 |
rogueApRSSIValueRSSI for AP detected.ro Integer32 .1.3.6.1.4.1.52.4.13.14.1.1.6 |
apRougeApControl OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.13.14.2 |
rogueApRADIUSAuthenticateValue is used to enable/disable RADIUS Authentication.rw Enumeration .1.3.6.1.4.1.52.4.13.14.2.1 |
rogueApClearThis object is set to clear(1) to clear the Rogue AP detection table. When read, the value
will have no meaning.rw Enumeration .1.3.6.1.4.1.52.4.13.14.2.2 |
apAdminMgnt OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.13.15 |
apAdminUsernameThis value indicates the username for management login.rw DisplayString .1.3.6.1.4.1.52.4.13.15.1 |
appAdminPasswordThis value indicates the password for management login.rw DisplayString .1.3.6.1.4.1.52.4.13.15.2 |
apResetMgt OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.13.16 |
apRestartOpCodeFileName of op-code file for start-up.rw DisplayString .1.3.6.1.4.1.52.4.13.16.1 |
apRestartControlSetting this object to warmBoot(2) causes the device to
restart the application software with current configuration
parameters saved in non-volatile memory. Setting this
object to coldBoot(3) causes the device to reinitialize
configuration parameters in non-volatile memory to default
values and restart the application software. When the device
is running normally, this variable has a value of running(1).rw Enumeration .1.3.6.1.4.1.52.4.13.16.2 |
apSNTPMgnt OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.13.17 |
apSNTPStateThis value indicates whether SNTP is enabled or not. At least one of the
SNTP servers must have a valid IP address before SNTP can be enabled.rw Enumeration .1.3.6.1.4.1.52.4.13.17.1 |
apSNTPPrimaryServerThis value indicates the IP address of the primary SNTP server.rw IpAddress .1.3.6.1.4.1.52.4.13.17.2 |
apSNTPSecondaryServerThis value indicates the IP address of the secondary SNTP server.rw IpAddress .1.3.6.1.4.1.52.4.13.17.3 |
apSNTPTimezoneThis value indicates which timezone to use.rw Enumeration .1.3.6.1.4.1.52.4.13.17.4 |
apSNTPDSTThis value indicates whether Daylight Savings Time is enabled or not.rw Enumeration .1.3.6.1.4.1.52.4.13.17.5 |
apSNTPDSTStartMonthThis value indicates the starting month for Daylight Savings Time.rw INTEGER .1.3.6.1.4.1.52.4.13.17.6 |
apSNTPDSTStartDayThis value indicates the starting day for Daylight Savings Time.rw INTEGER .1.3.6.1.4.1.52.4.13.17.7 |
apSNTPDSTEndMonthThis value indicates the ending month for Daylight Savings Time.rw INTEGER .1.3.6.1.4.1.52.4.13.17.8 |
apSNTPDSTEndDayThis value indicates the ending day for Daylight Savings Time.rw INTEGER .1.3.6.1.4.1.52.4.13.17.9 |
apDNSMgnt OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.13.18 |
apDNSPrimaryServerThis value indicates the IP address of the primary DNS server.rw IpAddress .1.3.6.1.4.1.52.4.13.18.1 |
apDNSSecondaryServerThis value indicates the IP address of the secondary DNS server.rw IpAddress .1.3.6.1.4.1.52.4.13.18.2 |
apIappMgnt OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.13.19 |
apIappEnabledWhether IAPP is enabled.rw Enumeration .1.3.6.1.4.1.52.4.13.19.1 |
apSyslogConfigMgnt OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.13.20 |
apLogConfigStateThis value indicates whether syslog is enabled.rw Enumeration .1.3.6.1.4.1.52.4.13.20.1 |
apSyslogConsoleStateThis value indicates whether syslog console logging is enabled.rw Enumeration .1.3.6.1.4.1.52.4.13.20.2 |
apSyslogLevelThis value indicates the syslog logging level.rw Enumeration .1.3.6.1.4.1.52.4.13.20.3 |
apSyslogServerTableTable of descriptive and status information about
configuration of each syslog server. SEQUENCE OF ApSyslogServerEntry .1.3.6.1.4.1.52.4.13.20.4 |
apSyslogServerEntryAn entry in the table, containing information
about configuration of one syslog server of the AP. ApSyslogServerEntry .1.3.6.1.4.1.52.4.13.20.4.1 |
apSyslogServerIndexIndex of the Syslog Server Integer32 .1.3.6.1.4.1.52.4.13.20.4.1.1 |
apSyslogServerStateThis value indicates whether the syslog server is enabled.rw Enumeration .1.3.6.1.4.1.52.4.13.20.4.1.2 |
apSyslogServerIPAddressThis value indicates the IP address of the syslog server.rw IpAddress SYNTAX DisplayString .1.3.6.1.4.1.52.4.13.20.4.1.3 |
apSyslogServerPortThis value indicates the UDP Port used by the syslog server.rw INTEGER .1.3.6.1.4.1.52.4.13.20.4.1.4 |
apEventLogMgnt OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.13.21 |
apEventLogTableThis table is a snapshot of the current event log. SEQUENCE OF ApEventLogEntry .1.3.6.1.4.1.52.4.13.21.1 |
apEventLogEntryAn entry in the table, containing one message
from the event log. ApEventLogEntry .1.3.6.1.4.1.52.4.13.21.1.1 |
apEventLogIndexIndex of the Event Log Message INTEGER .1.3.6.1.4.1.52.4.13.21.1.1.1 |
apEventLogMessageThe Event Log Messagero DisplayString .1.3.6.1.4.1.52.4.13.21.1.1.2 |
apEventLogClearThis object is set to 1 to clear the event log. When read, the value
will have no meaning.rw Enumeration .1.3.6.1.4.1.52.4.13.21.2 |
apWSLSupportMgnt OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.13.22 |
apWSLSupportControlThe administrative enable/disable state for
the control of the WSL function.rw Enumeration .1.3.6.1.4.1.52.4.13.22.1 |
apWSLSupportMasterAddressThis value indicates IP address of the main WSL.rw IpAddress SYNTAX DisplayString .1.3.6.1.4.1.52.4.13.22.2 |
apWSLSupportSecondaryAddressThis value indicates IP address of the peer WSL.rw IpAddress SYNTAX DisplayString .1.3.6.1.4.1.52.4.13.22.3 |
apWSLSupportPortThis value indicates the TCP Port used by the WSL server.rw INTEGER .1.3.6.1.4.1.52.4.13.22.4 |
apWSLSupportHeartbeatIntervalThis value indicates the WSL Heartbeat Interval.rw INTEGER .1.3.6.1.4.1.52.4.13.22.5 |
apWSLSupportHeartbeatLastChangeThe sysUpTime at which the Heartbeat was last
modified. The format is defined as hh:mm:ss - dd:mm:yyro TimeTicks SYNTAX DisplayString .1.3.6.1.4.1.52.4.13.22.6 |
apWSLSupportOperationModeThis attribute indicates that the WSL Operation Mode in
0: AP in standalone mode, or
1: AP in ETS WSL managed mode (associated mode).rw Enumeration .1.3.6.1.4.1.52.4.13.22.7 |
apWSLSupportRxThresholdThis value indicates the WSL CCA rejection threshold in dBm scale.rw INTEGER (-128..127) .1.3.6.1.4.1.52.4.13.22.8 |
apWSLSupportControlStatusThe operative enable/disable state for
the control of the WSL function.ro Enumeration .1.3.6.1.4.1.52.4.13.22.9 |
apWSLRFAreaPollControlThe administrative enable/disable state for
the control of the WSL RF Area Poll function.ro Enumeration .1.3.6.1.4.1.52.4.13.22.10 |
apWSLRFAreaPollControlStatusThe operative enable/disable state for
the control of the WSL RF Area Poll function.ro Enumeration .1.3.6.1.4.1.52.4.13.22.11 |
apWMMMgnt OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.13.23 |
apWMMControlTableTable for WMM configuration per radio. SEQUENCE OF ApWMMControlEntry .1.3.6.1.4.1.52.4.13.23.1 |
apWMMControlEntryAn Entry in the apWMMControlTable. ApWMMControlEntry .1.3.6.1.4.1.52.4.13.23.1.1 |
apWMMStateThis value indicates the WMM state.rw Enumeration .1.3.6.1.4.1.52.4.13.23.1.1.1 |
apWMMBssParamTableConceptual table for EDCA default parameter values at a non-AP
QSTA. This table shall contain the four entries of the EDCA
parameters corresponding to four possible ACs (access category):
1) AC_BE (best effort, ACI=0)
2) AC_BK (background, ACI=1)
3) AC_VI (video, ACI=2)
4) AC_VO (voice, ACI=3) SEQUENCE OF ApWMMBssParamEntry .1.3.6.1.4.1.52.4.13.23.2 |
apWMMBssParamEntryAn Entry (conceptual row) in the apWMMBssParamTable.
ifIndex - Each IEEE 802.11 interface is represented by an ifEntry.
Interface tables in this MIB module are indexed by ifIndex. ApWMMBssParamEntry .1.3.6.1.4.1.52.4.13.23.2.1 |
apWMMBssParamIndexThe index used to identify instances of the columnar
objects in the apWMMBssParam Table. The value of this variable is
1) 1 AC_BE (best effort, ACI=0)
2) 2 AC_BK (background, ACI=1)
3) 3 AC_VI (video, ACI=2)
4) 4 AC_VO (voice, ACI=3) INTEGER .1.3.6.1.4.1.52.4.13.23.2.1.1 |
apWMMBssParamCWminThis attribute shall specify the value of the minimum size of the
window in the exponent form that shall be used by a QSTA for a particular AC for
generating a random number for the backoff.rw INTEGER .1.3.6.1.4.1.52.4.13.23.2.1.2 |
apWMMBssParamCWmaxThis attribute shall specify the value of the maximum size of the
window in the exponent form that shall be used by a QSTA for a particular AC for
generating a random number for the backoff.rw INTEGER .1.3.6.1.4.1.52.4.13.23.2.1.3 |
apWMMBssParamAIFSNThis attribute shall specify the number of slots, after a SIFS
duration, that the QSTA, for a particular AC, shall sense the
medium idle either before transmitting or executing a backoff.rw INTEGER .1.3.6.1.4.1.52.4.13.23.2.1.4 |
apWMMBssParamTXOPLimitThis attribute shall specify the maximum time of
an TXOP in units of 32 microseconds for a given AC at a non-AP QSTA.rw INTEGER .1.3.6.1.4.1.52.4.13.23.2.1.5 |
apWMMBssParamAdmissionControlThis attribute, when TRUE, indicates that admission control is
mandatory for the given AC. When False, this attribute indicates
that the admission control is not mandatory for the given AC. The
default value for this parameter shall be FALSE.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.52.4.13.23.2.1.6 |
apWMMApParamTableConceptual table for EDCA default parameter values at the QAP.
This table shall contain the four entries of the EDCA
parameters corresponding to four possible ACs (access category):
1) AC_BE (best effort, ACI=0)
2) AC_BK (background, ACI=1)
3) AC_VI (video, ACI=2)
4) AC_VO (voice, ACI=3) SEQUENCE OF ApWMMApParamEntry .1.3.6.1.4.1.52.4.13.23.3 |
apWMMApParamEntryAn Entry (conceptual row) in the apWMMApParamTable.
ifIndex - Each IEEE 802.11 interface is represented by an ifEntry.
Interface tables in this MIB module are indexed by ifIndex. ApWMMApParamEntry .1.3.6.1.4.1.52.4.13.23.3.1 |
apWMMApParamIndexThe index used to identify instances of the columnar
objects in the apWMMApParam Table. The value of this variable is
1) 1 AC_BE (best effort, ACI=0)
2) 2 AC_BK (background, ACI=1)
3) 3 AC_VI (video, ACI=2)
4) 4 AC_VO (voice, ACI=3) INTEGER .1.3.6.1.4.1.52.4.13.23.3.1.1 |
apWMMApParamCWminThis attribute shall specify the value of the minimum size of the
window in the exponent form that shall be used by a QAP for a particular AC for
generating a random number for the backoff.rw INTEGER .1.3.6.1.4.1.52.4.13.23.3.1.2 |
apWMMApParamCWmaxThis attribute shall specify the value of the maximum size of the
window in the exponent form that shall be used by a QAP for a particular AC for
generating a random number for the backoff.rw INTEGER .1.3.6.1.4.1.52.4.13.23.3.1.3 |
apWMMApParamAIFSNThis attribute shall specify the number of slots, after a SIFS
duration, that the QAP, for a particular AC, shall sense the
medium idle either before transmitting or executing a backoff.rw INTEGER .1.3.6.1.4.1.52.4.13.23.3.1.4 |
apWMMApParamTXOPLimitThis attribute shall specify the maximum time of
an TXOP in units of 32 microseconds for a given AC at a QAP.rw INTEGER .1.3.6.1.4.1.52.4.13.23.3.1.5 |
apWMMApParamAdmissionControlThis attribute, when TRUE, indicates that admission control is
mandatory for the given AC. When False, this attribute indicates
that the admission control is not mandatory for the given AC. The
default value for this parameter shall be FALSE.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.52.4.13.23.3.1.6 |
apNotificationTrapTree OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.13.100 |
apNotificationObjects OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.13.100.1 |
apNotificationDot11MacAddrMac Address of the affected interface, returned with traps only.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.52.4.13.100.1.1 |
apNotificationDot11StationThis attribute holds the MAC address of the wireless stationro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.52.4.13.100.1.2 |
apNotificationDot11RequestTypeThis attribute defines the request type sent by the station.
Value = 1: Unknown request type
Value = 2: Association Request
Value = 3: Re-association Request
Value = 4: Authenticationro Enumeration .1.3.6.1.4.1.52.4.13.100.1.3 |
apNotificationDot11ReasonCodeThis attribute defines the reason for the failure of an operation.
Value = 1: Invalid mode/state
Value = 2: Station not authenticated.
Value = 3: Internal error
Value = 4: Out of sequence frame
Value = 5: Un-supported algorithm
Value = 6: Invalid frame length
Value = 7: WEP is required on the AP
Value = 8: WEP not allowed
Value = 9: Challenge text mismatchro Enumeration .1.3.6.1.4.1.52.4.13.100.1.4 |
apNotificationDot11IpAddressThis value indicates the IP address of the Access Pointro IpAddress .1.3.6.1.4.1.52.4.13.100.1.5 |
apNotificationDot11AuthenticatorMacAddrThis attribute holds the MAC address of the authenticator for the AP.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.52.4.13.100.1.6 |
apNotificationTrapObjects OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.13.100.2 |
sysSystemUpThe system up notification shall be sent when the AP
is fully up and running. NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.13.100.2.1 |
sysSystemDownThe system down notification shall be sent before the AP
is about to reboot. NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.13.100.2.2 |
sysRadiusServerChangedThe RADIUS server changed notification shall be sent when
the RADIUS server has changed from Primary / Secondary to
Secondary / Primary. NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.13.100.2.3 |
dot11StationAssociationThe associate notification shall be sent when a station successfully
associates with the Access Point. The value of the notification shall
include the MAC address of the station that has associated. NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.13.100.2.4 |
dot11StationReAssociationThe re-associate notification shall be sent when a station
successfully re-associates with the Access Point. The value of the
notification shall include the MAC address of the station
that has associated. NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.13.100.2.5 |
dot11StationAuthenticationThe authentication notification shall be sent when a station
successfully authenticates with the Access Point. The value of the
notification shall include the MAC address of the station
that has authenticated. NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.13.100.2.6 |
dot11StationRequestFailThe station request fail shall be sent out when a station
fails to associate / re-associate / authenticate with the
Access Point. The notification shall include the MAC address
of the station and the reason code for the failure. NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.13.100.2.7 |
dot1xMacAddrAuthSuccessThe 802.1X MAC address authentication success notification shall
be sent when a station successfully authenticates the MAC address
with the RADIUS server. The value of the notification shall
include the MAC address of the station that has authenticated. NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.13.100.2.9 |
dot1xMacAddrAuthFailThe 802.1X MAC address authentication failure notification shall
be sent when a station fails to authenticate the MAC address
with the RADIUS server. The value of the notification shall
include the MAC address of the station that failed to authenticate. NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.13.100.2.10 |
dot1xAuthNotInitiatedThe 802.1X authentication not initiated notification shall
be sent when a station did not initiate 802.1X authentication
with the RADIUS server. The value of the notification shall
include the MAC address of the station that did not initiate
802.1X authentication. NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.13.100.2.11 |
dot1xAuthSuccessThe 802.1X authentication success notification shall
be sent when a station successfully authenticates with the
RADIUS server. The value of the notification shall include
the MAC address of the station that has authenticated. NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.13.100.2.12 |
dot1xAuthFailThe 802.1X authentication failure notification shall
be sent when a station fails to authenticate with the
RADIUS server. The value of the notification shall include
the MAC address of the station that failed to authenticate. NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.13.100.2.13 |
localMacAddrAuthSuccessThe Local MAC address authentication success notification shall
be sent when a station successfully authenticates the MAC address
with the database stored locally within the AP. The value of the
notification shall include the MAC address of the station that
has authenticated. NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.13.100.2.14 |
localMacAddrAuthFailThe Local MAC address authentication failure notification shall
be sent when a station fails to authenticate the MAC address
with the database stored locally within the AP. The value of the
notification shall include the MAC address of the station that
has authenticated. NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.13.100.2.15 |
pppLogonFailThe PPP Logon failure notification shall be sent out when
the AP fails to login successfully to the PPP peer using the
supplied username and password. NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.13.100.2.16 |
iappStationRoamedFromThe IAPP Station Roamed-From Notification shall be sent out
whenever a station roams from another Access Point (AP) to
this AP. The notification shall include the MAC address of
the station and the IP address of the old AP. NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.13.100.2.17 |
iappStationRoamedToThe IAPP Station Roamed-To Notification shall be sent out
whenever a station roams to another Access Point (AP) from
this AP. The notification shall include the MAC address of
the station and the IP address of the new AP. NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.13.100.2.18 |
iappContextDataSentThe IAPP Context Data Sent notification shall be sent out
whenever the context data for a station has been sent to
the new AP with which the station has associated. The
notification shall include the MAC address of
the station and the IP address of the new AP. NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.13.100.2.19 |
sntpServerFailThe sntpServerFail notification shall be sent when the AP
fails to get time from the configured SNTP server. NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.13.100.2.20 |
dot11InterfaceAFailThe InterfaceAFail notification shall be sent out when
802.11a wireless interface has failed. NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.13.100.2.21 |
dot11InterfaceGFailThe InterfaceGFail notification shall be sent out when
802.11g wireless interface has failed. NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.13.100.2.22 |
dot11WirelessSTPDetectionThe WirelessSTPDetection notification shall be sent out when
wireless STP packet has detected. NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.13.100.2.23 |