CTRON-DECIV-ROUTER-MIB
Detailed view of the defined objects, syntax rules, and hierarchical paths.
215
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
215 total| Object Name |
|---|
nwDecIVRouter OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.2.2.2.3.3 |
IMPORTS Unknown .1.3.6.1.4.1.52.4.2.2.2.3.3 |
nwDecIVMibs OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.2.2.2.3.3.1 |
nwDecIVMibRevTextIndicates the current revision level of the DECnet Phase
IV MIB in textual format.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.52.4.2.2.2.3.3.1.1 |
nwDecIVComponents OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.2.2.2.3.3.2 |
nwDecIVSystem OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.2.2.2.3.3.2.1 |
nwDecIVSysConfig OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.1 |
nwDecIVSysRouterIdThe DECnet Address used to uniquely identify the host (device)
running DECnet Phase IV Routing Services. Since DECnet Phase IV
uses a single address to identify the host and all of its router
ports, rather than using an address per router port,
nwDecIVSysRouterID is the DECnet node address for all the router
ports on the device.rw DecIVAddress .1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.1.1 |
nwDecIVNodeTypeSpecifies the node type. Setting this value to 2, (routing-iv),
establishes the Routing Services-enabled device as a DECnet
Level 1, intra-area router. Setting this value to 2, establishes
the Routing Services-enabled device as a DECnet Phase IV Level 2,
or inter-area router.rw Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.1.2 |
nwDecIVMaxNodesSpecifies the maximum number of DECnet nodes allowed within an
area.rw INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.1.3 |
nwDecIVMaxBRASpecifies the maximum number of router adjacencies supported by
this node.rw INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.1.4 |
nwDecIVMaxBEASpecifies the maximum number of endnode adjacencies supported
by this node.rw INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.1.5 |
nwDecIVMaxHopsSpecifies the maximum number of hops allowed for a valid route
within the area. Any intra-area route consisting of a greater
number of hops than specified by nwDecIVMaxHops is considered
unreachable.rw INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.1.6 |
nwDecIVMaxCostSpecifies the maximum cost allowed for a valid route within the
area. Any intra-area route with a cost greater than nwDecIVMaxCost
is considered unreachable.rw INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.1.7 |
nwDecIVMaxVisitsSpecifies the maximum number of intra-area hops a packet can be
forwarded. A packet is dropped once it has been forwarded
nwDecIVMaxVisits.rw INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.1.8 |
nwDecIVNonBroadcastTimerSpecifies the periodic interval (in seconds) at which DECnet
Routing Services advertises its route table, on any non-broadcast
networks attached to any router port configured and enabled for
DECnet Phase IV Routing Services.rw TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.1.9 |
nwDecIVBroadcastTimerSpecifies the periodic interval (in seconds) at which DECnet
Routing Services advertises its route table on any multi-access
broadcast networks attached to any router port configured and
enabled for DECnet Phase IV Routing Services.rw TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.1.10 |
nwDecIVAreasSpecifies the maximum number of areas allowed within a Level 2
(inter-area)routing domain.rw INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.1.11 |
nwDecIVMaxAreaHopsSpecifies the maximum number of areas that can be hopped by
a valid inter-area route. Any inter-area route requiring a
greater number of areas to be hopped than specified by
nwDecIVMaxAreaHops is considered invalid.rw INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.1.12 |
nwDecIVMaxAreaCostSpecifies the maximum cost allowed for a valid Level 2
(inter-area) route. Any inter-area route with a cost greater than
nwDecIVMaxAreaCost is considered unreachable.rw INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.1.13 |
nwDecIVSysAdministration OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.2 |
nwDecIVSysAdminStatusSets the administrative state of DECnet Phase IV Routing Services,
system-wide. Enabled (3) causes DECnet Phase IV system-wide Routing
Services to become active on all router ports configured and enabled
for DECnet Phase IV Routing Services. Disabled (2) causes DECnet
Phase IV Routing Services to become inactive system-wide.rw Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.2.1 |
nwDecIVSysOperStatusIndicates the current operating condition of DECnet Phase IV
Routing Services system-wide. The value of nwDecIVSysOperStatus
indicates any problem with your DECnet Phase IV Routing Services
configuration. A value of 6 indicates that regardless of the value
of nwDecIVSysAdminStatus, DECnet Phase IV Routing Services is not
operating because of an invalid configuration.ro Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.2.2 |
nwDecIVSysAdminResetResets DECnet Phase IV Routing Services, system-wide. Reset (2)
forces a restart of DECnet Phase IV Routing Services without a
graceful shutdown on any active router ports and without affecting
any other routing services.rw Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.2.3 |
nwDecIVSysOperationalTimeIndicates the elapsed time, in hundredths of a second, that
nwDecIVSysOperStatus has been in it's current state.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.2.4 |
nwDecIVSysVersionIndicates the current revision level of the DECnet Phase IV Routing
Services firmware, in textual format.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.2.5 |
nwDecIVForwarding OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.2.2.2.3.3.2.2 |
nwDecIVFwdSystem OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1 |
nwDecIVFwdCounters OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1 |
nwDecIVFwdCtrAdminStatusSets the administrative state of the aggregate (system-wide)
DECnet packet and byte counters. Enabled (3) causes these counters
to become active. Disabled (2) causes these counters to become
inactive.rw Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.1 |
nwDecIVFwdCtrResetResets the aggregate (system-wide) DECnet packet and byte counters.
Reset (2) resets the DECnet aggregate counters to 0.
nwDecIVFwdCtrOperationalTime is also reset to 0.rw Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.2 |
nwDecIVFwdCtrOperationalTimeIndicates the elapsed time, in hundredths of a second, that
DecIVFwdCtrOperStatus has been in the current state.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.3 |
nwDecIVFwdCtrInPktsIndicates the total number of DECnet packets that have been
received, system-wide, during nwDecIVFwdCtrOperationalTime.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.4 |
nwDecIVFwdCtrOutPktsIndicates the total number of DECnet packets that have been
transmitted, system-wide, during nwDecIVFwdCtrOperationalTime.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.5 |
nwDecIVFwdCtrFwdPktsIndicates the total number of DECnet packets that have been
forwarded, system-wide, during nwDecIVFwdCtrOperationalTime.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.6 |
nwDecIVFwdCtrFilteredPktsIndicates the total number of DECnet packets that have been
administratively filtered, system-wide, during
nwDecIVFwdCtrOperationalTime.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.7 |
nwDecIVFwdCtrDiscardPktsIndicates the total number of DECnet packets that have been
discarded, system-wide, during nwDecIVFwdCtrOperationalTime.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.8 |
nwDecIVFwdCtrAddrErrPktsIndicates the total number of DECnet packets that have been
discarded, system-wide, during nwDecIVFwdCtrOperationalTime,
because of addressing errors in the DECnet header.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.9 |
nwDecIVFwdCtrLenErrPktsIndicates the total number of DECnet packets that have been
discarded, system-wide, during nwDecIVFwdCtrOperationalTime,
because an invalid packet length is contained in the DECnet header.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.10 |
nwDecIVFwdCtrHdrErrPktsIndicates the total number of DECnet packets that have been
discarded, system-wide, during nwDecIVFwdCtrOperationalTime,
because of an invalid DECnet header.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.11 |
nwDecIVFwdCtrInBytesIndicates the total number of bytes in the DECnet packets that
have been received, system-wide, during nwDecIVFwdCtrOperationalTime.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.12 |
nwDecIVFwdCtrOutBytesIndicates the total number of bytes in the DECnet packets that
have been transmitted, system-wide, during
nwDecIVFwdCtrOperationalTime.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.13 |
nwDecIVFwdCtrFwdBytesIndicates the total number of bytes in the DECnet packets
that have been forwarded, system-wide, during
nwDecIVFwdCtrOperationalTime.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.14 |
nwDecIVFwdCtrFilteredBytesIndicates the total number of bytes in the DECnet packets that
have been administratively filtered, system-wide, during
nwDecIVFwdCtrOperationalTime.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.15 |
nwDecIVFwdCtrDiscardBytesIndicates the total number of bytes in the DECnet packets that
have been discarded, system wide, during nwDecIVFwdCtrOperationalTime.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.16 |
nwDecIVFwdCtrHostInPktsIndicates the total number of DECnet packets that have been
successfully delivered to the local host, during
nwDecIVFwdCtrOperationalTime.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.17 |
nwDecIVFwdCtrHostOutPktsIndicates the total number of DECnet packets that have been
transmitted by the local host, during nwDecIVFwdCtrOperationalTime.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.18 |
nwDecIVFwdCtrHostDiscardPktsIndicates the total number of DECnet packets that have been
discarded by the local host, during nwDecIVFwdCtrOperationalTime,
due to a lack of host resources.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.19 |
nwDecIVFwdCtrHostInBytesIndicates the total number of bytes in the DECnet packets that
have been received by the local host, during
nwDecIVFwdCtrOperationalTime.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.20 |
nwDecIVFwdCtrHostOutBytesIndicates the total number of bytes in the DECnet packets that
have been transmitted by the local host, during
nwDecIVFwdCtrOperationalTime.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.21 |
nwDecIVFwdCtrHostDiscardBytesIndicates the total number of bytes in the DECnet packets that have
been discarded by the local host, during
nwDecIVFwdCtrOperationalTime, due to a lack of host resources.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.22 |
nwDecIVFwdInterfaces OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2 |
nwDecIVFwdIfConfig OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.1 |
nwDecIVFwdIfTableThis table contains an entry for each router port. This table is
indexed by nwDecIVFwdIfIndex, which indicates the value of MIB 2
ifIndex, which identifies the router port for which each entry exists. SEQUENCE OF NwDecIVFwdIfEntry .1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.1.1 |
nwDecIVFwdIfEntryEach entry specifies the DECnet Phase IV Routing Services
configuration for the router port for which the entry exists. NwDecIVFwdIfEntry .1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.1.1.1 |
nwDecIVFwdIfIndexIndicates the value of MIB 2 ifindex, which identifies the router
port for which the entry exists.ro INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.1.1.1.1 |
nwDecIVFwdIfAdminStatusSets the administrative state of DECnet Phase IV Routing Services
on the router port for which the entry exists. Enabled (3) causes
DECnet Phase IV Routing Services to become active. Disabled (2)
causes it to become inactive.rw Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.1.1.1.2 |
nwDecIVFwdIfOperStatusIndicates the current operating condition of DECnet Phase IV
Routing Services on the router port for which the entry exists.
The value of nwDecIVFwdIfOperStatus indicates any problem with the
configuration of DECnet Phase IV Routing Services on the router port.
value of 6 indicates that regardless of the value of
nwDecIVFwdIfAdminStatus, DECnet Phase IV Routing Services is not
operating because of an invalid port-level configuration.ro Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.1.1.1.3 |
nwDecIVFwdIfOperationalTimeIndicates the elapsed time, in hundredths of a second, that
nwDecIVFwdIfOperStatus has been in its current state.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.1.1.1.4 |
nwDecIVFwdIfControlThis object does not apply to this protocol. It is a common object,
inherited from the MIB framework used to provide a common management
interface to all the Cabletron Routing Services protocol-specific
MIBs. Setting this object has no effect.rw Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.1.1.1.5 |
nwDecIVFwdIfMtuSpecifies the Maximum Transmission Unit (MTU) for DECnet packets on
the router port for which the entry exists. This includes the DECnet
header and data, but does not include framing.rw INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.1.1.1.6 |
nwDecIVFwdIfForwardingControls the forwarding of DECnet packets on the router port for
which the entry exists. Enabled (3) causes DECnet packets to be
forwarded. Disabled (2) prevents DECnet packets from being forwarded.rw Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.1.1.1.7 |
nwDecIVFwdIfFrameTypeSpecifies the framing type for DECnet packets forwarded on the router
port for which the entry exists. Some frame types are only valid for
specific media types. The comments reflect those valid media types.rw Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.1.1.1.8 |
nwDecIVFwdIfAclIdentifierSpecifies the Access Control ID of the access control list in
effect for DECnet packets being routed on the router port for which
the entry exists. A value of 0 indicates that no access control list
is in effect.rw INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.1.1.1.9 |
nwDecIVFwdIfAclStatusControls the operation of any access control list configured
for DECnet traffic on the router port for which the entry exists.
Enabled (3) applies the access control list indicated by the value
of nwDecIVFwdIfAclIdentifier to all DECnet traffic being routed on
the port. Disabled (2) prevents the access control list from being
applied.rw Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.1.1.1.10 |
nwDecIVFwdIfCacheControlThis object does not apply to this protocol. It is a common object
inherited from the MIB framework used to provide a common management
interface to all the Cabletron Routing Services protocol-specific
MIBs. Setting this object has no effect.rw Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.1.1.1.11 |
nwDecIVFwdIfCacheEntriesThis object does not apply to this protocol. It is a common
object inherited from the MIB framework used to provide a
common management interface to all the Cabletron Routing
Services protocol-specific MIBs. Setting this object has no
effect.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.1.1.1.12 |
nwDecIVFwdIfCacheHitsThis object does not apply to this protocol. It is a common object
inherited from the MIB framework used to provide a common management
interface to all the Cabletron Routing Services protocol-specific MIBs.
Setting this object has no effect.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.1.1.1.13 |
nwDecIVFwdIfCacheMissesThis object does not apply to this protocol. It is a common object
inherited from the MIB framework used to provide a common management
interface to all the Cabletron Routing Services protocol-specific
MIBs. Setting this object has no effect.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.1.1.1.14 |
nwDecIVFwdIfCounters OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2 |
nwDecIVFwdIfCtrTableThis table contains an entry for each router port configured and
enabled for DECnet Phase IV Routing Services. SEQUENCE OF NwDecIVFwdIfCtrEntry .1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1 |
nwDecIVFwdIfCtrEntryEach entry indicates the current packet and byte count of DECnet
packets on each router port for which the entry exists. NwDecIVFwdIfCtrEntry .1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1 |
nwDecIVFwdIfCtrIfIndexIndicates the value of MIB 2 ifindex, which identifies the router
port for which the entry exists.ro INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.1 |
nwDecIVFwdIfCtrAdminStatusSets the administrative state of the per-port DECnet packet and
byte counters on the router port for which the entry exists. Enabled
(3) causes these counters to become active. Disabled (2) causes
these counters to become inactive.rw Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.2 |
nwDecIVFwdIfCtrResetResets the per-port DECnet packet and byte counters on the router
port for which the entry exists. Reset (2) resets the counters to 0.
nwDecIVFwdIfCtrOperationalTime is also reset to 0.rw Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.3 |
nwDecIVFwdIfCtrOperationalTimeIndicates the elapsed time, in hundredths of a second, that the
per-port DECnet packet and byte counters have been active on the
router port for which the entry exists.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.4 |
nwDecIVFwdIfCtrInPktsIndicates the total number of DECnet packets that have been
received, during nwDecIVFwdIfCtrOperationaltime, on the router port
for which the entry exists.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.5 |
nwDecIVFwdIfCtrOutPktsIndicates the total number of DECnet packets that have been
transmitted, during nwDecIVFwdIfCtrOperationalTime, on the router
port for which the entry exists.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.6 |
nwDecIVFwdIfCtrFwdPktsIndicates the total number of DECnet packets that have been
forwarded on the router port for which the entry exists, during
nwDecIVFwdCtrOperationalTime.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.7 |
nwDecIVFwdIfCtrFilteredPktsIndicates the total number of DECnet packets that have been
administratively filtered, during nwDecIVFwdIfCtrOperationalTime,
on the router port for which the entry exists.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.8 |
nwDecIVFwdIfCtrDiscardPktsIndicates the total number of DECnet packets that have been
discarded (dropped), during nwDecIVFwdIfCtrOperationalTime,
on the router port for which the entry exists.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.9 |
nwDecIVFwdIfCtrAddrErrPktsIndicates the total number of DECnet packets that have been
discarded because of addressing errors in the DECnet header,
during nwDecIVFwdIfCtrOperationalTime, on the router port for
which the entry exists.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.10 |
nwDecIVFwdIfCtrLenErrPktsIndicates the total number of DECnet packets that have been
discarded because an invalid packet length was contained in the
DECnet header, during nwDecIVFwdIfCtrOperationalTime, on the router
port for which the entry exists.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.11 |
nwDecIVFwdIfCtrHdrErrPktsIndicates the total number of DECnet packets that have been
discarded because of an invalid DECnet header, during
nwDecIVFwdIfCtrOperationalTime, on the router port for which the
entry exists.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.12 |
nwDecIVFwdIfCtrInBytesIndicates the total number of bytes in the DECnet packets that
have been received, during nwDecIVFwdIfCtrOperationalTime, on the
router port for which the entry exists.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.13 |
nwDecIVFwdIfCtrOutBytesIndicates the total number of bytes in the DECnet packets that have
been transmitted, during nwDecIVFwdIfCtrOperationalTime, on the router
port for which the entry exists.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.14 |
nwDecIVFwdIfCtrFwdBytesIndicates the total number of bytes in the DECnet packets that
have been forwarded, during nwDecIVFwdIfCtrOperationalTime, on the
router port for which the entry exists.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.15 |
nwDecIVFwdIfCtrFilteredBytesIndicates the total number of bytes in the DECnet packets that
have been administratively filtered, during
nwDecIVFwdIfCtrOperationalTime, on the router port for which the
entry exists.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.16 |
nwDecIVFwdIfCtrDiscardBytesIndicates the total number of bytes in the DECnet packets that
have been discarded, during nwDecIVFwdIfCtrOperationalTime, on the
router port for which the entry exists.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.17 |
nwDecIVFwdIfCtrHostInPktsIndicates the total number of DECnet packets that have been
delivered to the local host, during nwDecIVFwdIfCtrOperationalTime,
that were received on the router port for which the entry exists.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.18 |
nwDecIVFwdIfCtrHostOutPktsIndicates the total number of DECnet packets that have been
transmitted by the local host, during nwDecIVFwdIfCtrOperationalTime,
on the router port for which the entry exists.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.19 |
nwDecIVFwdIfCtrHostDiscardPktsIndicates the total number of DECnet packets that have been
discarded by the local host, during nwDecIVFwdIfCtrOperationalTime,
that were received on the router port for which the entry exists.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.20 |
nwDecIVFwdIfCtrHostInBytesIndicates the total number of bytes in the DECnet packets that
have been delivered to the local host, during
nwDecIVFwdIfCtrOperationalTime, that were received on the router port
for which the entry exists.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.21 |
nwDecIVFwdIfCtrHostOutBytesIndicates the total number of bytes in the DECnet packets that
have been transmitted by the local host, during
nwDecIVFwdIfCtrOperationalTime, on the router port for which the
entry exists.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.22 |
nwDecIVFwdIfCtrHostDiscardBytesIndicates the total number of bytes in the DECnet packets that
have been discarded by the local host, due to a lack of host
resources, that were received on the router port for which the entry
exists, during nwDecIVFwdIfCtrOperationalTime.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.23 |
nwDecIVTopology OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.2.2.2.3.3.2.4 |
nwDecIVDistanceVector OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1 |
nwDecIVProto OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1 |
nwDecIVProtoSystem OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1 |
nwDecIVProtoConfig OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.1 |
nwDecIVProtoAdminStatusSets the administrative state of the DECnet Phase IV
distance-vector-based routing protocol system-wide. Enabled (3)
causes the routing protocol to become active on all router ports
configured and enabled for DECnet Routing Services. Disabled (2)
causes the routing protocol to become inactive.rw Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.1.1 |
nwDecIVProtoOperStatusIndicates the current operating condition of the DECnet Phase
IV distance-vector-based routing protocol system-wide. The value
of nwDecIVProtoOperStatus indicates any problem with the DECnet
Phase IV distance-vector-based routing protocol configuration.
A value of 6 indicates that regardless of the value of
nwDecIVProtoAdminStatus, the DECnet Phase IV distance-vector-based
routing protocol is not operating because of an invalid configuration.ro Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.1.2 |
nwDecIVProtoAdminResetResets the DECnet Phase IV distance-vector-based routing
protocol. Reset (2) forces a system-wide restart of the protocol
without a graceful shut-down on any active router ports.rw Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.1.3 |
nwDecIVProtoOperationalTimeIndicates the elapsed time, in hundredths of a second, that
nwDecIVProtoOperStatus has been in current state.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.1.4 |
nwDecIVProtoVersionIndicates the current revision level of the DECnet Phase IV
distance-vector-based routing protocol firmware, in textual format.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.1.5 |
nwDecIVProtoStackSizeSpecifies the stack size of the DECnet Phase IV distance-vector-
based routing protocol thread. In order for a change of this value
to take effect, the protocol (nwDecIVProtoAdminReset), DECnet
Phase IV Routing Services (nwDecIVSysAdminReset), or the device
running Routing Services must be reset.rw INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.1.6 |
nwDecIVProtoThreadPrioritySpecifies the run-time execution priority of the DECnet Phase IV
distance-vector-based routing protocol thread. In order for a change
of this value to take effect, the protocol (nwDecIVProtoAdminReset),
DECnet Phase IV Routing Services (nwDecIVSysAdminReset), or the
device running Routing Services must be reset.rw INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.1.7 |
nwDecIVProtoDatabaseThresholdThis object does not apply to this protocol. It is a common object
inherited from the MIB framework used to provide a common management
interface to all the Cabletron Routing Services protocol-specific
MIBs. Setting this object has no effect.rw INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.1.8 |
nwDecIVProtoAgeOutThis object does not apply to this protocol. It is a common object
inherited from the MIB framework used to provide a common management
interface to all the Cabletron Routing Services protocol-specific
MIBs. Setting this object has no effect.rw INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.1.9 |
nwDecIVProtoHoldDownThis object does not apply to this protocol. It is a common object
inherited from the MIB framework used to provide a common management
interface to all the Cabletron Routing Services protocol-specific
MIBs. Setting this object has no effect.rw INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.1.10 |
nwDecIVProtoCounters OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.2 |
nwDecIVProtoCtrAdminStatusSets the administrative state of the aggregate (system-wide) DECnet
Phase IV distance-vector-based routing protocol packet and byte
counters. Enabled (3) causes these counters to become active.
Disabled (2) causes these counters to become inactive.rw Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.2.1 |
nwDecIVProtoCtrResetResets the aggregate (system-wide) DECnet Phase IV
distance-vector-based routing protocol packet and byte counters.
Reset (2) resets the DECnet aggregate counters to 0.
nwDecIVProtoCtrOperationalTime is also reset to 0.rw Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.2.2 |
nwDecIVProtoCtrOperationalTimeIndicates the elapsed time, in hundredths of a second, that
nwDecIVProtoCtrAdminStatus has been in it's current state.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.2.3 |
nwDecIVProtoCtrInPktsIndicates the total number of DECnet Phase IV distance-vector-based
routing protocol packets that have been received, system-wide,
during nwDecIVProtoCtrOperationalTime.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.2.4 |
nwDecIVProtoCtrOutPktsIndicates the total number of DECnet Phase IV distance-vector-based
routing protocol packets that have been transmitted, system-wide,
during nwDecIVProtoCtrOperationalTime.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.2.5 |
nwDecIVProtoCtrFilteredPktsIndicates the total number of DECnet Phase IV distance-vector-based
routing protocol packets that have been administratively filtered,
system-wide, during nwDecIVProtoCtrOperationalTime.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.2.6 |
nwDecIVProtoCtrDiscardPktsIndicates the total number of the DECnet Phase IV distance-vector
-based routing protocol packets that have been discarded,
system-wide, during nwDecIVProtoCtrOperationalTime.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.2.7 |
nwDecIVProtoCtrInBytesIndicates the total number of bytes in the DECnet Phase IV
distance-vector based routing protocol packets that have been
received, system-wide, during nwDecIVProtoCtrOperationalTime.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.2.8 |
nwDecIVProtoCtrOutBytesIndicates the total number of bytes in the DECnet Phase IV
distance-vectorbased routing protocol packets that have been
transmitted, system-wide, during nwDecIVProtoCtrOperationalTime.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.2.9 |
nwDecIVProtoCtrFilteredBytesIndicates the total number of bytes in the DECnet Phase IV
distance-vectorbased routing protocol packets that have been
administratively filtered, system-wide, during
nwDecIVProtoCtrOperationalTime.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.2.10 |
nwDecIVProtoCtrDiscardBytesIndicates the total number of bytes in the DECnet Phase IV
distance-vectorbased routing protocol packets that have been
discarded system-wide, during nwDecIVProtoCtrOperationalTime.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.2.11 |
nwDecIVProtoInterface OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2 |
nwDecIVProtoIfConfig OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1 |
nwDecIVProtoIfTableThis table contains an entry for each router port. Each entry can
contain different values, allowing the routing protocol configuration
to vary from router port to router port. This table is indexed by
nwDecIVProtoIfIndex, which indicates the value of MIB 2 ifIndex,
which identifies the router port for which each entry exists. SEQUENCE OF NwDecIVProtoIfEntry .1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1 |
nwDecIVProtoIfEntryEach entry contains the DECnet Phase IV distance-vector-based
routing protocol configuration for the router port for which the
entry exists. NwDecIVProtoIfEntry .1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1 |
nwDecIVProtoIfIndexIndicates the value of MIB 2 ifindex, which identifies the router
port for which the entry exists.ro INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1.1 |
nwDecIVProtoIfAdminStatusSets the administrative state of the DECnet Phase IV
distance-vector-based routing protocol on the router port for which
the entry exists. Enabled (3) causes the routing protocol to become
active on the router port. Disabled (2) causes it to become inactive.rw Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1.2 |
nwDecIVProtoIfOperStatusIndicates the current operating condition of the DECnet Phase IV
distance-vector-based routing protocol on the router port for which
the entry exists. The value of nwDecIVProtoIfOperStatus indicates
any problem with your routing protocol configuration on the router
port. A value of 6 indicates that regardless of the value of
nwDecIVProtoIfAdminStatus, the routing protocol is not operating
because of an invalid configuration.ro Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1.3 |
nwDecIVProtoIfOperationalTimeIndicates the elapsed time, in hundredths of a second, that
nwDecIVProtoIfOperStatus has been in it`s current state.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1.4 |
nwDecIVProtoIfVersionIndicates the revision level of the DECnet Phase IV
distance-vector-based routing protocol firmware on the router port
for which the entry exists, in textual format.rw INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1.5 |
nwDecIVProtoIfAdvertisementSets the interval, in seconds, at which the DECnet Phase IV
distance-vectorbased routing protocol advertises its route table on
the router port for which the entry exists. Change this value to
cause the DECnet Phase IV distance-vector-based routing protocol to
advertise its route table more or less frequently on the router port.rw INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1.6 |
nwDecIVProtoIfFloodDelayThis object does not apply to this protocol. It is a common object
inherited from the MIB framework used to provide a common management
interface to all the Cabletron Routing Services protocol-specific MIBs.
Setting this object has no effect.rw INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1.7 |
nwDecIVProtoIfRequestDelayThis object does not apply to this protocol. It is a common object
inherited from the MIB framework used to provide a common management
interface to all the Cabletron Routing Services protocol-specific MIBs.
Setting this object has no effect.rw INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1.8 |
nwDecIVProtoIfPrioritySets the priority of the DECnet Phase IV distance-vector-based
routing protocol on the router port for which the entry exists.
Within an area, the router with the highest value for
nwDecIVProtoIfPriority becomes the priority or designated router.
The highest possible value for nwDecIVProtocolIfPriority is 127. Set
this value high to cause your DECnet Phase IV Routing Services-enabled
device to become the designated router. Set this value low to guarantee
that it does not become the designated router.rw INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1.9 |
nwDecIVProtoIfHelloTimerSets the interval, in seconds, at which DECnet Phase IV
distance-vector-based routing protocol sends Hello packets on the
router port for which the entry exists.rw INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1.10 |
nwDecIVProtoIfSplitHorizonThis object does not apply to this protocol. It is a common object
inherited from the MIB framework used to provide a common management
interface to all the Cabletron Routing Services protocol-specific MIBs.
Setting this object has no effect.rw Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1.11 |
nwDecIVProtoIfPoisonReverseThis object does not apply to this protocol. It is a common object
inherited from the MIB framework used to provide a common management
interface to all the Cabletron Routing Services protocol-specific MIBs.
Setting this object has no effect.rw Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1.12 |
nwDecIVProtoIfSnoopingControls the operation of DECnet Phase IV distance-vector-based
routing protocol snooping on the router port. When snooping is
enabled the DECnet Phase IV distance-vector-based routing protocol
operates in passive mode, so that it receives route information,
builds and maintains a route table, but does not advertise the route
table or send updates on the router port for which the entry exists.rw Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1.13 |
nwDecIVProtoIfTypeIndicates whether the directly connected network segment does or
does not support broadcast media access.ro Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1.14 |
nwDecIVProtoIfXmitCostSets the cost of transmitting a packet on the network segment
connected to the router port for which the entry exists. The DECnet
Phase IV distance-vector-based routing protocol picks the route with
the least total nwDecIVProtoIfXmitCost as the best route. If
nwDecIVProtocolIfXmitCost, also known as path cost, is the same for
all possible routes , the best route chosen is the route with the
least number of hops is chosen as the best route.rw INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1.15 |
nwDecIVProtoIfAclIdentifierSpecifies the Access Control ID of the access control list in
effect for DECnet Phase IV distance-vector-based routing protocol
packets on the router port for which the entry exists. A value of 0
indicates that there is no access control list in effect for DECnet
Phase IV distance-vector-based routing protocol packets on the router
port.rw INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1.16 |
nwDecIVProtoIfAclStatusControls the operation of the access control list identified by
nwDecIVProtoIfAclIdentifier. Enabled (3) applies the access control
list to all DECnet Phase IV distance-vector-based routing protocol
packet traffic on the router port for which the entry exists. Disabled
(2) prevents the access control list from being applied.rw Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1.17 |
nwDecIVProtoIfCounters OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.2 |
nwDecIVProtoIfCtrTableThis table contains an entry for each router port. This table is
indexed by nwDecIVProtoIfCtrIfIndex which indicates the value of
MIB2 ifindex, which identifies the router port for which the entry
exists. SEQUENCE OF NwDecIVProtoIfCtrEntry .1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.2.1 |
nwDecIVProtoIfCtrEntryEach entry indicates the current packet and byte count of DECnet
Phase IV distance-vector-based routing protocol packets on the router
port for which the entry exists. NwDecIVProtoIfCtrEntry .1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.2.1.1 |
nwDecIVProtoIfCtrIfIndexIndicates the value of MIB 2 ifindex, which identifies the router
port for which the entry exists.ro INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.2.1.1.1 |
nwDecIVProtoIfCtrAdminStatusSets the administrative state of the per-port DECnet Phase IV
distance-vectorbased routing protocol packet and byte counters on
the router port for which the entry exists. Enabled (3) causes these
counters to become active. Disabled (2) causes these counters to
become inactive.rw Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.2.1.1.2 |
nwDecIVProtoIfCtrResetResets the per-port DECnet Phase IV distance-vector-based routing
protocol packet and byte counters on the router port for which the
entry exists. Reset (2) resets the counters to 0.
nwDecIVProtoIfCtrOperationalTime is also reset to 0.rw Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.2.1.1.3 |
nwDecIVProtoIfCtrOperationalTimeIndicates the elapsed time, in hundredths of a second, that
nwDecIVProtoIfCtrAdminStatus has been in the current state.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.2.1.1.4 |
nwDecIVProtoIfCtrInPktsIndicates the total number of DECnet Phase IV distance-vector-based
routing protocol packets that have been received, during
nwDecIVProtoIfCtrOperationalTime, on the router port for which the
entry exists.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.2.1.1.5 |
nwDecIVProtoIfCtrOutPktsIndicates the total number of DECnet Phase IV distance-vector-based
routing protocol packets that have been transmitted, during
nwDecIVProtoIfCtrOperationalTime, on the router port for which the
entry exists.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.2.1.1.6 |
nwDecIVProtoIfCtrFilteredPktsIndicates the total number of DECnet Phase IV distance-vector-based
routing protocol packets that have been administratively filtered,
during nwDecIVProtoIfCtrOperationalTime, on the router port for which
the entry exists.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.2.1.1.7 |
nwDecIVProtoIfCtrDiscardPktsIndicates the total number of DECnet Phase IV distance-vector-based
routing protocol packets that have been discarded, during
nwDecIVProtoIfCtrOperationalTime, that were received on the router
port for which the entry exist.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.2.1.1.8 |
nwDecIVProtoIfCtrInBytesIndicates the total number of bytes in the DECnet Phase IV
distance-vector-based routing protocol packets that have been
received, during nwDecIVProtoIfCtrOperationalTime, on the router
port for which the entry exists.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.2.1.1.9 |
nwDecIVProtoIfCtrOutBytesIndicates the total number of bytes in the DECnet Phase IV
distance-vector-based routing protocol packets that have been
transmitted, during nwDecIVProtoIfCtrOperationalTime, on the router
port for which the entry exists.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.2.1.1.10 |
nwDecIVProtoIfCtrFilteredBytesIndicates the total number of bytes in the DECnet Phase IV
distance-vector-based routing protocol packets that have been
administratively filtered, during nwDecIVProtoIfCtrOperationalTime,
that were received on the router port for which the entry exists.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.2.1.1.11 |
nwDecIVProtoIfCtrDiscardBytesIndicates the total number of bytes in the DECnet packets that have
been discarded, during nwDecIVProtoIfCtrOperationalTime, that were
received on the router port for which the entry exists.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.2.1.1.12 |
nwDecIVLinkState OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.2 |
nwDecIVFib OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.2.2.2.3.3.2.5 |
nwDecIVFibTableThis table contains an entry for each route being used to forward
DECnet data packets.. SEQUENCE OF NwDecIVFibEntry .1.3.6.1.4.1.52.4.2.2.2.3.3.2.5.1 |
nwDecIVFibEntryEach entry in the table describes a route to a particular DECnet
destination network and node. NwDecIVFibEntry .1.3.6.1.4.1.52.4.2.2.2.3.3.2.5.1.1 |
nwDecIVFibNodeIdContains the DECnet Address of the destination node of the route
for which the entry exists.ro DecIVAddress .1.3.6.1.4.1.52.4.2.2.2.3.3.2.5.1.1.1 |
nwDecIVFibNextHopNodeIdContains the DECnet Address of the next hop router for the route
for which the entry exists.rw DecIVAddress .1.3.6.1.4.1.52.4.2.2.2.3.3.2.5.1.1.2 |
nwDecIVFibNextHopIfIndicates the value of MIB 2 ifindex, which identifies the router
port through which the route exists.rw INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.3.2.5.1.1.3 |
nwDecIVFibRouteTypeIndicates the status of the route. A value of 3 indicates that the
destination is on the network segment that is directly connected to
the router port identified by nwDecIVFibNextHopIf. A value of 4
indicates that the destination is on an indirectly connected network
segment, which is reachable through the next hop router indicated by
the value of nwDecIVFibNextHopNodeId. A value of 2 indicates that the
route is invalid.rw Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.3.2.5.1.1.4 |
nwDecIVEndSystems OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.2.2.2.3.3.2.6 |
nwDecIVHostsSystem OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.2.2.2.3.3.2.6.1 |
nwDecIVHostsInterfaces OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.2.2.2.3.3.2.6.2 |
nwDecIVHostsToMedia OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.2.2.2.3.3.2.6.3 |
nwDecIVHostMapTableThe DecIV Address translation table used for mapping
a DecIV address to a circuit identifier (if applicable),
corresponding port number, and framing type. SEQUENCE OF NwDecIVHostMapEntry .1.3.6.1.4.1.52.4.2.2.2.3.3.2.6.3.1 |
nwDecIVHostMapEntryEach entry contains one DecIVAddress to circuit
equivalence. Also provided is the framing required to
converse with this host, and the corresponding logical
port number. NwDecIVHostMapEntry .1.3.6.1.4.1.52.4.2.2.2.3.3.2.6.3.1.1 |
nwDecIVHostMapIfIndexThis is the primary (major) index into the DecIV HostMap
table. This number corresponds to the index into the MIB-2
Interfaces Group which describes the DecIV router port for which
the entry exists.ro INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.3.2.6.3.1.1.1 |
nwDecIVHostMapDecIVAddrThe DecIVAddress of the host on the corresponding interface
and circuit (if applicable).ro DecIVAddress .1.3.6.1.4.1.52.4.2.2.2.3.3.2.6.3.1.1.2 |
nwDecIVHostMapTypeSetting this object to the value invalid(2) has
the effect of invalidating the corresponding entry in the
nwDecIVHostMapTable. That is, it effectively dissasociates
the circuitand/or interface identified with said entry from the
mapping identified with said entry. It is an implementation-
specific matter as to whether the agent removes an invalidated
entry from the table. Accordingly, management stations must be
prepared to receive tabular information from agents that
corresponds to entries not currently in use. Proper inter-
pretation of such entries requires examination of the relevant
wDecIVHostMapType object.rw Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.3.2.6.3.1.1.3 |
nwDecIVHostMapCircuitIDThe identifier for the virtual circuit present on the
interface. On an interface configured for Frame Relay,
this number is the DLCI for the DecIV Address at the end of
the circuit. For non-WAN interfaces, the value of this
object is zero.rw INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.3.2.6.3.1.1.4 |
nwDecIVHostMapFramingSpecifies the framing type required to converse with the
host for which this entry exists.rw Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.3.2.6.3.1.1.5 |
nwDecIVHostMapPortNumberThe unique value for the logical port number. It's value
ranges between 1 and a maximum value which is dependent on both
the number of configured interfaces in the system and the number
of circuits present on those interfaces which are of WAN type.ro INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.3.2.6.3.1.1.6 |
nwDecIVAccessControl OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.2.2.2.3.3.2.7 |
nwDecIVAclValidEntriesIndicates the number of valid entries that exist in the access
control list table, nwDecIVAclTable.ro Gauge .1.3.6.1.4.1.52.4.2.2.2.3.3.2.7.1 |
nwDecIVAclTableThis table contains the access control list information for DECnet
traffic. This table contains entries each of which specifies whether
packet forwarding between a particular source destination pair is
permitted or denied. Each entry is part of a particular access
control list. Each list is identified by a unique Access Control ID.
Each list may contain multiple entries ordered by sequence number.
When an Access Control List is searched, it is searched in sequence
number order and the first match found ends the search. If no match
is found, access defaults to permitted. SEQUENCE OF NwDecIVAclEntry .1.3.6.1.4.1.52.4.2.2.2.3.3.2.7.2 |
nwDecIVAclEntryEach entry contains DECnet source/destination access information. NwDecIVAclEntry .1.3.6.1.4.1.52.4.2.2.2.3.3.2.7.2.1 |
nwDecIVAclIdentifierThis is the primary (major) index into the DECnet access control
list table. This value identifies each access control list by a
unique identifier, a number arbitrarily assigned by the user. All
entries that have the same value for nwDecIVAclIdentifier belong to
the same access control list.ro INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.3.2.7.2.1.1 |
nwDecIVAclSequenceThis is the secondary (minor) index into the DECnet access control
list table. This number corresponds to a sequence number used to
order multiple entries within the same access control list.ro INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.3.2.7.2.1.2 |
nwDecIVAclPermissionSpecifies whether access is allowed or denied between the source
and destination address pair. Note that source and destination are
interchangeable when bi-directional control is selected. To remove
an existing entry set nwDecIVAclPermission to invalid (2). Invalid
entries disappear after reboot.rw Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.3.2.7.2.1.3 |
nwDecIVAclMatchesIndicates the number of matches on this entry that have resulted
in the permit/deny access restriction being applied as part of the
forwarding process.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.3.2.7.2.1.4 |
nwDecIVAclDestAddressSpecifies the destination DECnet Address used to compare for
matches on the access control list. Either the Area ID or Node ID
of this address may be set to 0, a wildcard value which matches all
areas or all nodes.rw DecIVAddress .1.3.6.1.4.1.52.4.2.2.2.3.3.2.7.2.1.5 |
nwDecIVAclSrcAddressSpecifies the source DECnet Address used to compare for matches on
the access control list. Either the Area ID or Node ID of this
address may be set to a wildcard value which matches all areas or
all nodes.rw DecIVAddress .1.3.6.1.4.1.52.4.2.2.2.3.3.2.7.2.1.6 |
nwDecIVFilters OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.2.2.2.3.3.2.8 |
nwDecIVRedirector OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.2.2.2.3.3.2.9 |
nwDecIVEvent OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.2.2.2.3.3.2.10 |
nwDecIVEventLogConfig OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.1 |
nwDecIVEventAdminStatusSets the administrative state of DECnet event logging. Enabled (3)
causes the event log to become active. Disabled (2) causes the event
log to become inactive.rw Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.1.1 |
nwDecIVEventMaxEntriesSets the maximum number of entries allowed in the event log table.
When the number of entries reaches the value of nwDecIVEventMaxEntries,
the first (oldest) entry is deleted to allow a new entry to be added.rw INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.1.2 |
nwDecIVEventTraceAllEnabled (3) allows logging of all event types on all router ports
for all protocols and components. Disabled (2) causes the filter
table to specify which events to log.rw Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.1.3 |
nwDecIVEventLogFilterTable OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.2 |
nwDecIVEventFilterTableThis table contains and entry for each event filter configured for
DECnet Phase IV Routing Services events. SEQUENCE OF NwDecIVEventFilterEntry .1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.2.1 |
nwDecIVEventFilterEntryEach entry describes an event filter which defines a particular type
of event to be logged to the event log. The value of
nwDecIVEventFltrProtocol indicates the value used either in the
nwRtgProtocolTable or the nwComponentTable in the Cabletron Routing
Services MIB, which identifies the protocol or component to which the
entry applies. NwDecIVEventFilterEntry .1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.2.1.1 |
nwDecIVEventFltrProtocolIndicates the value of the Cabletron Routing Services MIB
nwRtgProtocolInstance or nwComponentRtgInstance which identifies the
protocol involved in the event for which the event filter exists.ro INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.2.1.1.1 |
nwDecIVEventFltrIfNumSpecifies the router port involved in the event for which the event
filter exists.ro INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.2.1.1.2 |
nwDecIVEventFltrControlSet this value to 3 to add the entry to the event filter table. Set
this value to 2 to remove the entry from the event filter table.rw Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.2.1.1.3 |
nwDecIVEventFltrTypeThis 6 bit mask specifies the types of events to be logged. By
default all 6 bits are set to 1, indicating that all types of events
are to be logged. Setting any bit to 0 removes an event type from
this field and prevents that type of event from being logged. Setting
any bit to 1 adds an event type to this field and enables that type
of event to be logged.rw Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.2.1.1.4 |
nwDecIVEventFltrSeveritySpecifies the level of severity an event must meet in order to be
logged. Controls the amount of event logging by ignoring events of a
lower priority than specified by this filter value. `Highmed' ignores
only events of the lowest severity. `Highlow' logs all events highest
priority through lowest. `Highest' severity causes all events except
those of the highest severity to be ignored. `Highmed' severity is the
default setting which causes only events of the lowest severity to be
ignored. `Highlow' severity logs all events, regardless of severity.rw Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.2.1.1.5 |
nwDecIVEventFltrActionSpecifies how the events are to be logged. Logging to the `log'
stores the events in the event log table (nwDecIVEventLogTable).
Logging to'trap' sends events out through the trap mechanism.rw Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.2.1.1.6 |
nwDecIVEventLogTable OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.3 |
nwDecIVEventTableThis table contains an entry for each event that has been
logged. SEQUENCE OF NwDecIVEventEntry .1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.3.1 |
nwDecIVEventEntryEach entry contains the information about an event that has
been logged to the event table. NwDecIVEventEntry .1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.3.1.1 |
nwDecIVEventNumberAn ordinal value assigned to the event for which the log entry
exists. nwDecIVEventNumber is assigned so that each event in the
event log can be uniquely identified by the value of
nwDecIVEventNumber.ro INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.3.1.1.1 |
nwDecIVEventTimeIndicates the time at which the event was logged to the event
log.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.3.1.1.2 |
nwDecIVEventTypeIndicates the type of event that was logged.ro Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.3.1.1.3 |
nwDecIVEventSeverityIndicates the severity that was assigned to the event.ro Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.3.1.1.4 |
nwDecIVEventProtocolIndicates the value of the Cabletron Routing Services MIB
nwRtgProtocolInstance or nwComponentInstance which identifies the
protocol or component that was involved in the event.ro INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.3.1.1.5 |
nwDecIVEventIfNumIndicates the router port that was involved in the event.ro INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.3.1.1.6 |
nwDecIVEventTextStringContains the actual text string that was logged.ro OCTET STRING .1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.3.1.1.7 |
nwDecIVWorkGroup OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.2.2.2.3.3.2.11 |