CTRON-APPN-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for CTRON-APPN-MIB.
272
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
272 total| Object Name |
|---|
nwAppnRouter OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.2.2.2.3.5 |
IMPORTS Unknown .1.3.6.1.4.1.52.4.2.2.2.3.5 |
nwAppnMibs OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.2.2.2.3.5.1 |
nwAppnMibRevTextIndicates the current revision level of the Cabletron APPN
Router MIB in textual format.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.52.4.2.2.2.3.5.1.1 |
nwAppnComponents OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.2.2.2.3.5.2 |
nwAppnSystem OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.1 |
nwAppnSysConfig OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.1.1 |
nwAppnSysRouterIdSpecifies the APPN Fully-Qualified Control Point name that is used
to uniquely identify APPN Routing Services in an APPN network. The
name format is NNNNNNNN.CCCCCCCC where NNNNNNNN is the network
identifier and CCCCCCCC is the Control Point name. Valid characters
to make up these two strings are uppercase letters A through Z,
numerics 0 through 9, and the special characters $, @, and #. The
first character of the string must NOT be numeric. Each string must
be a maximum length of 8 characters with no embedded spaces and the
strings are joined by a dot. nwAppnSysRouterId cannot be modified
while APPN routing services is in any operational state other than
DISABLED as reflected in nwAppnSysOperStatus. Otherwise, the
request will be rejected.rw DisplayString .1.3.6.1.4.1.52.4.2.2.2.3.5.2.1.1.1 |
nwAppnSysCfgLocalNode OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.1.1.2 |
nwAppnSysNodeTypeIndicates the node type supported by APPN Routing Services which
is always of type Network Node.ro Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.5.2.1.1.2.1 |
nwAppnSysCpAliasSpecifies the Control Point alias name used by APPN Routing
Services.rw DisplayString .1.3.6.1.4.1.52.4.2.2.2.3.5.2.1.1.2.2 |
nwAppnSysModeCosMapSpecifies whether mode to COS mapping is supported by
APPN Routing Services.rw Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.5.2.1.1.2.3 |
nwAppnSysMdsSupportSpecifies whether Management Services supports Multiple
Domain Support and Management Services capabilities.rw Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.5.2.1.1.2.4 |
nwAppnSysMaxLocatesSpecifies maximum Number of locate requests that APPN Routing
Services can concurrently process. Note: if nwAppnSysMaxLocates is
set to a value too small, it will be internally increased to a
higher value after APPN Routing Services has been successfully
enabled. A subsequent GET operation on nwAppnSysMaxLocates will
reflect this new value.rw INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.1.1.2.6 |
nwAppnSysDirCacheSizeSpecifies number of located resources maintained in the Directory
Cache. Note: if nwAppnSysDirCacheSize is set to a value too small,
it will be internally increased to a higher value after APPN routing
services has been successfully enabled. A subsequent GET
operation on nwAppnSysDirCacheSize will reflect this new value.rw INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.1.1.2.7 |
nwAppnSysMaxDirEntriesSpecifies maximum number of directory entries. If zero is selected,
the number of entries is unlimited.rw INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.1.1.2.8 |
nwAppnSysLocateTimeoutSpecifies time in seconds before a network search will timeout. Zero
indicates that the search has no timeout.rw INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.1.1.2.9 |
nwAppnSysRegCdsSpecifies whether the local or domain resources can be registered
with the Central Directory Server.rw Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.5.2.1.1.2.10 |
nwAppnSysMdsSendQSizeSpecifies size of the MDS send alert Queue.rw INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.1.1.2.11 |
nwAppnSysCosSizeSpecifies maximum number of COS definitions maintained in the COS
database weights cache. It determines the size of the COS Database
weights cache. Note: if nwAppnSysCosSize is set to a value too
small, it will be internally increased to a higher value after
APPN Routing Services has been successfully enabled. A subsequent
GET operation on nwAppnSysCosSize will reflect this new value.rw INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.1.1.2.12 |
nwAppnSysTreeSizeSpecifies the number of routes maintained in the Topology Database
routing tree cache. Note: if nwAppnSysTreeSize is set to a value
too small, it will be internally increased to a higher value after
APPN Routing Services has been successfully enabled. A subsequent
GET operation on nwAppnSysTreeSize will reflect this new value.rw INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.1.1.2.13 |
nwAppnSysTreeUseLimitMaximum number of times a cached tree will be used to compute a
route before the tree is discarded and recomputed. This
allows the APPN Routing Services to balance sessions among
equal weight routes. A low value provides better load balancing
at the expense of increased activation latency.rw INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.1.1.2.14 |
nwAppnSysMaxTdmNodesSpecifies maximum number of nodes that can be stored in the Topology
Database. Zero means unlimited.rw INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.1.1.2.15 |
nwAppnSysMaxTdmTGsSpecifies maximum number of transmission groups that can be stored in
Topology Database. Zero means unlimited.rw INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.1.1.2.16 |
nwAppnSysMaxIsrSessionsSpecifies maximum number of intermediate routing sessions permitted
by APPN Routing Services at one time. This must be a non-negative
number.rw INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.1.1.2.18 |
nwAppnSysIsrUpperThreshThe thresholds control the congestion status of APPN routing
services. If the number of ISR sessions exceeds the upper
threshold, congestion status changes from uncongested to congested.
When this occurs, the status will not become uncongested until the
the number of ISR sessions fall below the lower threshold. The
lower threshold should be less than the upper threshold to prevent
thrashing. The upper threshold should be lower than
nwAppnSysMaxIsrSessions. This must be a non-negative number.rw INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.1.1.2.19 |
nwAppnSysIsrLowerThreshSpecifes the number of ISR sessions at which congestion status will
revert to uncongested. This must be a non-negative number.
nwAppnSysIsrLowerThresh must be less than nwAppnSysIsrUpperThresh
to prevent thrashing.rw INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.1.1.2.20 |
nwAppnSysIsrMaxRuSizeSpecifies maximum RU size supported for intermediate sessions.
Note: the number provided will be rounded up to the
next valid RU size if necessary after APPN Routing Services has
been successfully enabled. A subsequent GET operation on
nwAppnSysMaxLocates will reflect this new value.rw INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.1.1.2.21 |
nwAppnSysIsrRcvPaceWindSpecifies suggested receive pacing window size for intermediate
sessions. This value may be used as a fixed window size for
fixed pacing, or as a tuning value for adaptive pacing.rw INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.1.1.2.22 |
nwAppnSysRtAddResistSpecifies a desirability factor for APPN Routing Services to
perform intermediate session routing. 255 is least desirable
and 0 is more desirable.rw INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.1.1.2.23 |
nwAppnSysStopTypeSpecifies the type of APPN Routing Services shutdown.
Once specified, select disable from nwAppnSysAdminStatus. The
shutdown choices are as follows:
abort(1) All APPN Routing Services components are immediately
stopped and resources released. To become active again,
the APPN Routing Services must be enabled.
immediate(2) APPN Routing Services immediately deactivates all links
then performs abort(1) processing.
quiesce(3) APPN Routing Services indicates to other APPN network
nodes that it is quiesced. Session limits
are reset on all modes, UNBINDs are issued
on all endpoint sessions (CP-CP sessions last),
and then immediate(2) processing is performed.
quiesceIsr(4) Allows all intermediate sessions to end,
then performs the quiesce(3) processing.rw Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.5.2.1.1.2.24 |
nwAppnSysBlockNumThis represents the 3 hexadecimal digit block number which
precedes the 5 digit id number in the 8 digit node id used in
XIDs and Alerts. The block number identifies the product type.
Both the block number and id number combined, uniquely identify
this instance of APPN Routing Services within the installation
network.rw DisplayString .1.3.6.1.4.1.52.4.2.2.2.3.5.2.1.1.2.25 |
nwAppnSysIdNumThis represents the 5 hexadecimal digit id number which follows
the 3 digit block number in the 8 digit node id used in XIDs and
Alerts. The id number uniquely identifies this instance of APPN
Routing Services within a product type indicated by the block number.
Both the block number and id number combined, uniquely identify
this instance of APPN Routing Services within the installation
network.rw DisplayString .1.3.6.1.4.1.52.4.2.2.2.3.5.2.1.1.2.26 |
nwAppnSysCfgTables OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.1.1.3 |
nwAppnSysLuTableThis table contains entries for LUs that are owned by adjacent
LEN nodes. Defining or deleting an entry is equivalent to defining
or deleting an entry in the directory database. To add an entry,
set nwAppnSysLuControl to other. To delete an entry, set
nwAppnSysLuControl to delete. SEQUENCE OF NwAppnSysLuEntry .1.3.6.1.4.1.52.4.2.2.2.3.5.2.1.1.3.1 |
nwAppnSysLuEntryEach entry defines an LU entry in the directory database. The
fully qualified CP name and the name of the LU are the indexes into
this table. NwAppnSysLuEntry .1.3.6.1.4.1.52.4.2.2.2.3.5.2.1.1.3.1.1 |
nwAppnSysCpNameSpecifies the fully qualified name of the Control Point
containing the LU being defined. The format of this name
is NNNNNNNN.CCCCCCCC where NNNNNNNN is the network identifier and
CCCCCCCC is the LU or Control Point name. Valid characters to make
up these two strings are uppercase letters A through Z, numerics 0
through 9 and the special charcters $, @, and #. The first character
of the name must NOT be numeric. Each string must be a maximum length
of 8 characters with no embedded spaces and the strings are joined by
a dot. This CP name must appear as an Adjacent CP in a link station
definition where the adjacent CP type is EN and CP-CP session support
is NO.rw DisplayString .1.3.6.1.4.1.52.4.2.2.2.3.5.2.1.1.3.1.1.1 |
nwAppnSysLuNameSpecifies the name of the LU being registered. The name format is
LLLLLLLL where LLLLLLLL are the characters: uppercase letters
A through Z, numerics 0 through 9, and the special characters
$, @, and #. The first character of the name must NOT be numeric.
The string must be a maximum length of 8 characters with no
embedded spaces. Note that the nework identifier of the LU is
taken from the fully qualified control point name of the adjacent
LEN node (nwAppnSysCpName) which owns the LU.rw DisplayString .1.3.6.1.4.1.52.4.2.2.2.3.5.2.1.1.3.1.1.2 |
nwAppnSysLuControlSet this object to delete to remove an entry.rw Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.5.2.1.1.3.1.1.3 |
nwAppnSysAdministration OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.1.2 |
nwAppnSysAdminStatusSets the system-wide administrative state of APPN Routing Services.
If enable(3) is selected, APPN Routing Services is activated.
There are two cases: the very first activation, and activations
subsequent to the successful first activation. Before activating
APPN Routing Services the very first time, nwAppnSysRouterId in
the System Configuration branch and all objects under
nwAppnSysCfgLocalNode must be assigned a value. If not explicitly
assigned, default values will be used for objects under
nwAppnSysCfgLocalNode. After this first activation has completed
successfully, all objects under nwAppnSysCfgLocalNode will be
saved in non-volatile RAM and restored for the next node activation
at power up time. After this subsequent power up, enable(3) may be
selected without setting nwAppnSysRouterId or any objects under
under nwAppnSysCfgLocalNode. Those values defined prior to the
last power up or reset will be used.
If disable(2) is selected, APPN Routing Services will become
inactive in the manner specifed by nwAppnSysStopType. To
modify objects under nwAppnSysCfgLocalNode, nwAppnSysAdminStatus
must be disabled.rw Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.5.2.1.2.1 |
nwAppnSysOperStatusIndicates the current operating system-wide status of APPN
Routing Services.ro Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.5.2.1.2.2 |
nwAppnSysAdminResetResets APPN Routing Services system-wide. Reset (2) forces a
restart of APPN Routing Services without a graceful shutdown on
any active router ports, without affecting any other routing
services.rw Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.5.2.1.2.3 |
nwAppnSysOperationalTimeIndicates the elapsed time, in hundredths of a second, that
nwAppnOperStatus has been in its current state.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.52.4.2.2.2.3.5.2.1.2.4 |
nwAppnSysVersionIndicates the current revision level of APPN routing
services in textual format.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.52.4.2.2.2.3.5.2.1.2.5 |
nwAppnForwarding OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2 |
nwAppnFwdSystem OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.1 |
nwAppnFwdCounters OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.1.1 |
nwAppnFwdCtrAdminStatusSets the administrative state of the aggregate, system-wide,
port Message Unit (MU) and byte counters. Enabled (3) causes
these counters to become active. Disabled (2) causes these
counters to become inactive.rw Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.1.1.1 |
nwAppnFwdCtrResetResets the aggregate, system-wide port Message Unit (MU)
and byte counters. Reset (2) resets the aggregate counters to 0.
nwAppnFwdCtrOperationalTime is also reset to 0.rw Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.1.1.2 |
nwAppnFwdCtrOperationalTimeIndicates the elapsed time, in hundredths of a second,
that nwAppnFwdCtrAdminStatus has been in the current state.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.1.1.3 |
nwAppnFwdCtrInMusIndicates the total number of Message Units (MU)s that have
been received system-wide (for all ports) during
nwAppnFwdCtrOperationalTime.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.1.1.4 |
nwAppnFwdCtrOutMusIndicates the total number of Message Units (MU)s that have
been transmitted system-wide (for all ports) during
nwAppnFwdCtrOperationalTime.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.1.1.5 |
nwAppnFwdCtrFwdMusIndicates the total number of Message Units (MU)s that have
been forwarded system-wide (for all ports) during
nwAppnFwdCtrOperationalTime.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.1.1.6 |
nwAppnFwdCtrFilteredMusThis object does not apply to this protocol. It is a common
object, inherited from the MIB framework used to provide a
common management interface to all the Cabletron Routing Services
protocol-specific MIBs.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.1.1.7 |
nwAppnFwdCtrDiscardMusThis object does not apply to this protocol. It is a common
object, inherited from the MIB framework used to provide a
common management interface to all the Cabletron Routing Services
protocol-specific MIBs.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.1.1.8 |
nwAppnFwdCtrAddrErrMusIndicates the total number of Message Units (MUs)
that have been received system-wide (for all ports), during
nwAppnFwdCtrOperationalTime, that contain an address error(s)
in the SNA header.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.1.1.9 |
nwAppnFwdCtrLenErrMusIndicates the total number of Message Units (MUs) that have
been received system-wide (for all ports), during
nwAppnFwdCtrOperationalTime, that contain a length error.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.1.1.10 |
nwAppnFwdCtrHdrErrMusIndicates the total number of Message Units (MUs) that have
been received system-wide (for all ports), during
nwAppnFwdCtrOperationalTime, that contain an SNA header error
other than an address or length error.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.1.1.11 |
nwAppnFwdCtrInBytesIndicates number of bytes in Message Units (MUs) that have
been received system-wide (for all ports), during
nwAppnFwdCtrOperationalTime.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.1.1.12 |
nwAppnFwdCtrOutBytesIndicates the total number of bytes in Message Units (MUs) that
have been forwarded system-wide (for all ports), during
nwAppnFwdCtrOperationalTime.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.1.1.13 |
nwAppnFwdCtrFwdBytesIndicates the total number of bytes in Message Units (MUs) that
have been forwarded system-wide (for all ports), during
nwAppnFwdCtrOperationalTime.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.1.1.14 |
nwAppnFwdCtrFilteredBytesThis object does not apply to this protocol. It is a common
object, inherited from the MIB framework used to provide a
common management interface to all the Cabletron Routing Services
protocol-specific MIBs.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.1.1.15 |
nwAppnFwdCtrDiscardBytesThis object does not apply to this protocol. It is a common
object, inherited from the MIB framework used to provide a
common management interface to all the Cabletron Routing Services
protocol-specific MIBs.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.1.1.16 |
nwAppnFwdCtrHostInMusIndicates the total number of Message Units (MUs) that have
been delivered system-wide (for all ports), to local half
sessions during nwAppnFwdCtrOperationalTime.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.1.1.17 |
nwAppnFwdCtrHostOutMusIndicates the total number of Message Units (MUs) that have
been successfully sent from local half sessions system-wide
(for all ports), to Path Control during
nwAppnFwdCtrOperationalTime.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.1.1.18 |
nwAppnFwdCtrHostDiscardMusThis object does not apply to this protocol. It is a common
object, inherited from the MIB framework used to provide a
common management interface to all the Cabletron Routing Services
protocol-specific MIBs.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.1.1.19 |
nwAppnFwdCtrHostInBytesIndicates the total number of bytes in Message Units (MUs)
that have been delivered system-wide (for all ports), to
local half sessions during nwAppnFwdCtrOperationalTime.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.1.1.20 |
nwAppnFwdCtrHostOutBytesIndicates the total number of bytes in Message Units (MUs)
that have been successfully sent from local half sessions
system-wide (for all ports), to Path Control during
nwAppnFwdCtrOperationalTime.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.1.1.21 |
nwAppnFwdCtrHostDiscardBytesThis object does not apply to this protocol. It is a common
object, inherited from the MIB framework used to provide a
common management interface to all the Cabletron Routing Services
protocol-specific MIBs.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.1.1.22 |
nwAppnFwdInterfaces OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2 |
nwAppnFwdIfConfig OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1 |
nwAppnFwdIfTableThis table contains an entry for each router port which can
be used by APPN Routing Services. This table is indexed by
nwAppnFwdIfIndex, which indicates the value of MIB 2 ifindex
which identifes the router port for which an entry exists.
These port configuration entries will be provided automatically
based on physical port configuration. Such entries cannot be
deleted - only modified. SEQUENCE OF NwAppnFwdIfEntry .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.1 |
nwAppnFwdIfEntryEach entry specifies the APPN Routing Services port
configuration for the router port for which the entry exists. NwAppnFwdIfEntry .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.1.1 |
nwAppnFwdIfIndexIndicates the value of MIB2 ifindex, which identifies the
router port for which the entry exists.ro INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.1.1.1 |
nwAppnFwdIfAdminStatusSets the administrative state of an APPN Routing Services
port for which the entry exists. enabled(3) causes the
APPN Routing Services port to become active. disable(2)
causes it to become inactive. There are various choices
for the method by which the port can be disabled, which are
enumerated by nwAppnExtIfStopType.rw Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.1.1.2 |
nwAppnFwdIfOperStatusIndicates the current operating condition of the APPN Routing
Services port for which the entry exists.ro Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.1.1.3 |
nwAppnFwdIfOperationalTimeIndicates the elapsed time, in hundredths of a second, that
nwAppnFwdIfOperStatus has been in the current state.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.1.1.4 |
nwAppnFwdIfControlThis object does not apply to this protocol. It is a common
object, inherited from the MIB framework used to provide a
common management interface to all the Cabletron Routing Services
protocol-specific MIBs. Setting this object has no effect.rw Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.1.1.5 |
nwAppnFwdIfMtuThis object does not apply to this protocol. It is a common
object, inherited from the MIB framework used to provide a
common management interface to all the Cabletron Routing Services
protocol-specific MIBs. Setting this object has no effect.rw INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.1.1.6 |
nwAppnFwdIfForwardingThis object does not apply to this protocol. It is a common
object, inherited from the MIB framework used to provide a
common management interface to all the Cabletron Routing Services
protocol-specific MIBs. Setting this object has no effect.rw Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.1.1.7 |
nwAppnFwdIfFrameTypeSpecifies the framing type for the APPN Routing Services port
for which the entry exists.rw Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.1.1.8 |
nwAppnFwdIfAclIdentifierThis object does not apply to this protocol. It is a common
object, inherited from the MIB framework used to provide a
common management interface to all the Cabletron Routing Services
protocol-specific MIBs. Setting this object has no effect.rw INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.1.1.9 |
nwAppnFwdIfAclStatusThis object does not apply to this protocol. It is a common
object, inherited from the MIB framework used to provide a
common management interface to all the Cabletron Routing Services
protocol-specific MIBs. Setting this object has no effect.rw Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.1.1.10 |
nwAppnFwdIfCacheControlThis object does not apply to this protocol. It is a common
object, inherited from the MIB framework used to provide a
common management interface to all the Cabletron Routing Services
protocol-specific MIBs. Setting this object has no effect.rw Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.1.1.11 |
nwAppnFwdIfCacheEntriesThis object does not apply to this protocol. It is a common
object, inherited from the MIB framework used to provide a
common management interface to all the Cabletron Routing Services
protocol-specific MIBs. Setting this object has no effect.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.1.1.12 |
nwAppnFwdIfCacheHitsThis object does not apply to this protocol. It is a common
object, inherited from the MIB framework used to provide a
common management interface to all the Cabletron Routing Services
protocol-specific MIBs. Setting this object has no effect.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.1.1.13 |
nwAppnFwdIfCacheMissesThis object does not apply to this protocol. It is a common
object, inherited from the MIB framework used to provide a
common management interface to all the Cabletron Routing Services
protocol-specific MIBs. Setting this object has no effect.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.1.1.14 |
nwAppnExtensionTableThis table contains additional APPN definitions for each
physical port. Entries cannot be added to or deleted from this
table. With the exception of nwAppnExtIfStopType, objects in
this table may only be modified when nwAppnFwdIfAdminStatus
is disabled. Note: if APPN Routing Services is not active, no
entries will exist for this table. SEQUENCE OF NwAppnExtEntry .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.2 |
nwAppnExtEntryEach entry specifies additional APPN configuration parameters
for the port for which this entry exists. NwAppnExtEntry .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.2.1 |
nwAppnExtIfIndexSpecifies the primary index into the APPN port extension table.
This number corresponds to the index into the nwAppnFwdIfTable.ro INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.2.1.1 |
nwAppnExtIfPortNameSpecifies the user friendly name for this port.ro DisplayString .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.2.1.2 |
nwAppnExtIfPortTypeSpecifies the type of line used by the port. The value
corresponds to one of the following: nonswitched(1),
switched(2), or satf(3).rw Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.2.1.4 |
nwAppnExtIfDlcTypeSpecifies the type of DLC using the port.ro Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.2.1.5 |
nwAppnExtIfMaxRBtuSizeSpecifies the maximum Message Unit (MU) size that can be received.rw INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.2.1.6 |
nwAppnExtIfTotLsActLimSpecifies the total number of links that can be active on this
port. If nwAppnExtIfPortType = nonswitched(1) and
nwAppnExtIfLocalLsRole = negotiable(1), or secondary(3), then
this value must be set to 1.rw INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.2.1.7 |
nwAppnExtIfInbLsActLimSpecifies the total number of inbound links that can be active on
this port. If nwAppnExtIfPortType = nonswitched(1) and
nwAppnExtIfLocalLsRole = negotiable(1) or primary(2), then this
value must be set to 0.rw INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.2.1.8 |
nwAppnExtIfOutbLsActLimSpecifies the total number of outbound links that can be active on
this port. If nwAppnExtIfPortType = nonswitched(1) and
nwAppnExtIfLocalLsRole = negotiable(1), then this value must be
set to 0. If nwAppnExtIfLocalLsRole = primary(2), then this value
must be set the same as nwAppnExtIfTotLsActLim.rw INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.2.1.9 |
nwAppnExtIfLocalLsRoleSpecifies the link station role - primary, secondary, or
negotiable. For nwAppnExtIfPortType = satf(3), the link station
role must be negotiable(1).rw Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.2.1.10 |
nwAppnExtIfActXidXchgLimitSpecifies the total number of activation XIDs that may be
exchanged.rw INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.2.1.11 |
nwAppnExtIfNonActXidXchgLimitSpecifies the total number of non-activation XIDs that may be
exchanged.rw INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.2.1.12 |
nwAppnExtIfLsXmitRcvCapSpecifies the link station's transmit/receive capability.rw Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.2.1.13 |
nwAppnExtIfMaxIfrmRcvdSpecifies the maximum number of I-frames received before an
acknowledgment is sent to the sender.rw INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.2.1.14 |
nwAppnExtIfDfltTargetPacingSpecifies the pacing window size for BINDs on this transmission
group.rw INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.2.1.15 |
nwAppnExtIfDfltMaxSBtuSizeSpecifies the maximum Message Unit (MU) size which can be sent.rw INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.2.1.16 |
nwAppnExtIfDfltEffectCapSpecifies the default maximum kilo bits per second rate
(line speed) for all links on this port.rw INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.2.1.17 |
nwAppnExtIfDfltConnectCostSpecifies the default cost per connect time for all link
stations on this port. 0 is the lowest cost and 255 is the
largest cost.rw INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.2.1.18 |
nwAppnExtIfDfltByteCostSpecifies the default Cost per Byte for link stations. 0 is
the lowest cost and 255 is the largest cost.rw INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.2.1.19 |
nwAppnExtIfDfltSecuritySpecify one of the following security selections:
non-secure - specifies no security.
public switched - data flows over a public switched
network.
underground cable - data transmitted over a secure
underground cable.
secure conduit - line is secure conduit that is not
guarded.
guarded conduit - conduit that is protected against
physical tapping.
encrypted - encryption over the line.
guarded radiation - line is proected against physical
and radiation tapping.rw Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.2.1.20 |
nwAppnExtIfDfltPropDelaySpecifies the propagation delay which represents the relative
time it takes for a signal to travel the length of the link in
microseconds, with some of the more common default values
enumerated. The default times in parentheses are in microseconds.
These default values fall into the following ranges:
minimum - no propagation delay
negligible, lan - less than 480 microseconds
terrestrial, telephone - between 480 and 49,512
microseconds
packetswitched - between 49,512 and 245,760
microseconds
long, satellite - more than 245760 microseconds.
maximum - the maximum propagation delay.rw Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.2.1.21 |
nwAppnExtIfDfltUsrDef1Specifies user defined parameter 1.rw INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.2.1.22 |
nwAppnExtIfDfltUsrDef2Specifies user defined parameter 2.rw INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.2.1.23 |
nwAppnExtIfDfltUsrDef3Specifies user defined parameter 3.rw INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.2.1.24 |
nwAppnExtIfStopTypeSpecifies the type of shutdown for APPN Routing Services
on the port. Once set, nwAppnFwdIfAdminStatus may
be set to disable. The disable choices are as follows:
immediate(1) causes the link stations belonging to the
physical port to be disabled immediately
without flushing pending messages and
without initiating an orderly disconnect sequence.
orderly(2) causes pending messages in link stations to be
flushed, followed by an orderly disconnect
sequence. The link station is then disabled.rw Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.2.1.25 |
nwAppnExtIfCpCpSuppSpecifies whether CP-CP sessions are permitted on dynamic
links generated on this port.rw Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.2.1.26 |
nwAppnExtIfLimitedRsrcSpecifies whether dynamic links generated on this port
are a limited resource. A limited resource link will
be deactivated when there are no sessions using the link.rw Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.2.1.27 |
nwAppnExtIfAddressSpecifies the physical address of this port depending on the
media type. For token ring or ethernet ports, the information is
the 6 byte MAC address which starts in byte 1 and ends in byte 6.
For token ring ports the MAC address must be specified in non-
canonical format. For ethernet ports the MAC address must be
specified in canonical format. For frame relay ports, there is
no associated address, i.e., it will be a zero length octet string.ro OCTET STRING .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.2.1.28 |
nwAppnExtIfSsapFor token ring or ethernet ports specifies the Source SAP Address
of this port.rw OCTET STRING .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.2.1.29 |
nwAppnIfCn OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.3 |
nwAppnIfCnPortTableThis table contains definitions for the Connection
Network port table which defines which local ports can
access a connection network. To add a row to the table,
nwAppnIfCnPtFqName and nwAppnIfCnPtName are required entries.
To delete a row, set the control field to delete.
Adding the first row for a connection network implicitly
creates the connection network and deleting the last
remaining row for a connection network implicitly removes
the connection network. SEQUENCE OF NwAppnIfCnPortEntry .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.3.1 |
nwAppnIfCnPortEntrySpecifies the APPN Connection Network port definitions. NwAppnIfCnPortEntry .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.3.1.1 |
nwAppnIfCnPtFqNameSpecifies the fully-qualified Name of the Virtual Routing Node.
The name format is NNNNNNNN.CCCCCCCC where NNNNNNNN is the
network identifier and CCCCCCCC is the Control Point name. Valid
characters to make up these two strings are uppercase letters
A through Z, numerics 0 through 9, and the special characters
$, @, and #. The first character of the name must NOT be
numeric. Each string must be a maximum length of 8 characters
with no embedded spaces and the strings are joined by a dot.rw DisplayString .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.3.1.1.1 |
nwAppnIfCnPtNameSpecifies one of the ports which can access this Connection
Network.rw DisplayString .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.3.1.1.2 |
nwAppnIfCnPtControlSet this object to delete to delete this port from this
Connection Network.rw Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.3.1.1.3 |
nwAppnIfCnTgCharTableThis table contains the APPN definitions for a Connection
Network's transmission group characteristics. Rows may be
neither added nor deleted, only modified. Rows are
added/deleted implicitly through CnPortTable. SEQUENCE OF NwAppnIfCnTgCharEntry .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.3.2 |
nwAppnIfCnTgCharEntrySpecifies the APPN transmission group characteristics for
the Connection Network. NwAppnIfCnTgCharEntry .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.3.2.1 |
nwAppnIfCnTgFqNameSpecifies the fully-qualified Name of the Virtual Routing Node.
The name format is NNNNNNNN.CCCCCCCC where NNNNNNNN is the
network identifier and CCCCCCCC is the Control Point name. Valid
characters to make up these two strings are uppercase letters
A through Z, numerics 0 through 9, and the special characters
#, $, and @. The first character of the name must NOT be
numeric. Each string must be a maximum length of 8 characters
with no embedded spaces and the strings are joined by a dot.rw DisplayString .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.3.2.1.1 |
nwAppnIfCnTgEffectCapSpecifies the maximum kilo bits per second rate (link speed) for
the connection network.rw INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.3.2.1.2 |
nwAppnIfCnTgConnectCostSpecifies the cost per connect time for the Connection Network.
0 is the lowest cost and 255 is the largest cost.rw INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.3.2.1.3 |
nwAppnIfCnTgByteCostSpecifies the cost per byte for the Connection Network.
0 is the lowest cost and 255 is the largest cost.rw INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.3.2.1.4 |
nwAppnIfCnTgSecurityFor the Connection Network, specify one of the following
security selections:
non-secure - specifies no security.
public switched - data flows over a public switched
network.
underground cable - data transmitted over a secure
underground cable.
secure conduit - line is secure conduit that is not
guarded.
guarded conduit - conduit that is protected against
physical tapping.
encrypted - encryption over the line.
guarded radiation - line is proected against physical
and radiation tapping.rw Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.3.2.1.5 |
nwAppnIfCnTgPropDelaySpecifies the propagation delay which represents the time it
takes for a signal to travel the length of the link in
microseconds, with some of the more common default values
enumerated. The default times in parentheses are in microseconds.
These default values fall into the following ranges:
minimum - no propagation delay
negligible, lan - less than 480 microseconds
terrestrial, telephone - between 480 and 49,512
microseconds
packetswitched - between 49,512 and 245,760
microseconds
long, satellite - more than 245760 microseconds.
maximum - the maximum propagation delay.rw Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.3.2.1.6 |
nwAppnIfCnTgUsrDef1Specifies user defined parameter 1.rw INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.3.2.1.7 |
nwAppnIfCnTgUsrDef2Specifies user defined parameter 2.rw INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.3.2.1.8 |
nwAppnIfCnTgUsrDef3Specifies user defined parameter 3.rw INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.1.3.2.1.9 |
nwAppnFwdIfCounters OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.2 |
nwAppnFwdIfCtrTableThis table contains the Message Unit (MU) and byte counters for
each port configured and enabled for APPN Routing Services. SEQUENCE OF NwAppnFwdIfCtrEntry .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.2.1 |
nwAppnFwdIfCtrEntryEach entry indicates Message Units (MU) and byte counts on
the router port for which this entry exists. NwAppnFwdIfCtrEntry .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.2.1.1 |
nwAppnFwdIfCtrIfIndexIndicates the value of MIB 2 ifindex, which identifies the
router port for which the entry exists. This is the primary
index into the APPN per-port counter table.ro INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.2.1.1.1 |
nwAppnFwdIfCtrAdminStatusSets the administrative state of the per-port Message Unit
(MU) and byte counters on the router port for which the entry
exists. enabled(3) causes these counters to become active.
disabled(2) causes these counters to become inactive.rw Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.2.1.1.2 |
nwAppnFwdIfCtrResetResets the per-port Message Unit (MU) and byte counters on the
router port for which this entry exists. reset (2) resets the
counters to 0. nwAppnFwdIfCtrOperationalTime is also reset to 0.rw Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.2.1.1.3 |
nwAppnFwdIfCtrOperationalTimeIndicates the amount of time in hundreths of a second that the
per-port Message Unit (MU) and byte counters have been active on
the APPN routing services port for which this entry exists.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.2.1.1.4 |
nwAppnFwdIfCtrInMusIndicates the total number of Message Units (MU)s that have been
received, during nwAppnFwdIfCtrOperationaltime on the router port
for which this entry exists.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.2.1.1.5 |
nwAppnFwdIfCtrOutMusIndicates the total number of Message Units (MU)s that have been
transmitted, during nwAppnFwdIfCtrOperationalTime, on the router
port for which this entry exists.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.2.1.1.6 |
nwAppnFwdIfCtrFwdMusIndicates the total number of Message Units (MU)s that have
been forwarded during nwAppnFwdIfCtrOperationalTime on the router
port for which this entry exists.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.2.1.1.7 |
nwAppnFwdIfCtrFilteredMusThis object does not apply to this protocol. It is a common
object, inherited from the MIB framework used to provide a
common management interface to all the Cabletron Routing Services
protocol-specific MIBs.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.2.1.1.8 |
nwAppnFwdIfCtrDiscardMusThis object does not apply to this protocol. It is a common
object, inherited from the MIB framework used to provide a
common management interface to all the Cabletron Routing Services
protocol-specific MIBs.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.2.1.1.9 |
nwAppnFwdIfCtrAddrErrMusIndicates the total number of Message Units (MUs) that contain
an address error in the SNA header that have been received
during nwAppnFwdIfCtrOperationalTime on the router port for which
this entry exists.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.2.1.1.10 |
nwAppnFwdIfCtrLenErrMusIndicates the total number of Message Units (MUs) that contain
a length error that have been received during
nwAppnFwdIfCtrOperationalTime on the router port for which
this entry exists.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.2.1.1.11 |
nwAppnFwdIfCtrHdrErrMusIndicates the total number of Message Units (MUs) that contain
a header error other than an address or length error that have
been received during nwAppnFwdIfCtrOperationalTime on the router
port for which this entry exists.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.2.1.1.12 |
nwAppnFwdIfCtrInBytesIndicates the total number of bytes in the Message Units (MU)s
that have been received, during nwAppnFwdIfCtrOperationalTime,
on the router port for which the entry exists.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.2.1.1.13 |
nwAppnFwdIfCtrOutBytesIndicates the total number of bytes in the Message Units (MU)s
that have been transmitted, during nwAppnFwdIfCtrOperationalTime,
on the router port for which the entry exists.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.2.1.1.14 |
nwAppnFwdIfCtrFwdBytesIndicates the total number of bytes in Message Units (MU)s that
have been forwarded during nwAppnFwdIfCtrOperationalTime on the
router port for which this entry exists.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.2.1.1.15 |
nwAppnFwdIfCtrFilteredBytesThis object does not apply to this protocol. It is a common
object, inherited from the MIB framework used to provide a
common management interface to all the Cabletron Routing Services
protocol-specific MIBs.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.2.1.1.16 |
nwAppnFwdIfCtrDiscardBytesThis object does not apply to this protocol. It is a common
object, inherited from the MIB framework used to provide a
common management interface to all the Cabletron Routing Services
protocol-specific MIBs.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.2.1.1.17 |
nwAppnFwdIfCtrHostInMusIndicates the total number of Message Units (MUs) that have
been delivered to local half sessions during
nwAppnFwdIfCtrOperationalTime on the router port for which this
entry exists.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.2.1.1.18 |
nwAppnFwdIfCtrHostOutMusIndicates the total number of Message Units (MUs) that have
been successfully sent from local half sessions to Path Control
during nwAppnFwdIfCtrOperationalTime on the router port for
which this entry exists.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.2.1.1.19 |
nwAppnFwdIfCtrHostDiscardMusThis object does not apply to this protocol. It is a common
object, inherited from the MIB framework used to provide a
common management interface to all the Cabletron Routing Services
protocol-specific MIBs.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.2.1.1.20 |
nwAppnFwdIfCtrHostInBytesIndicates the total number of bytes in Message Units (MUs)
that have been delivered to local half sessions during
nwAppnFwdIfCtrOperationalTime on the router port for which this
entry exists.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.2.1.1.21 |
nwAppnFwdIfCtrHostOutBytesIndicates the total number of bytes in Message Units (MUs) that
have been successfully sent from local half sessions to Path
Control during nwAppnFwdIfCtrOperationalTime on the router port
for which this entry exists.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.2.1.1.22 |
nwAppnFwdIfCtrHostDiscardBytesThis object does not apply to this protocol. It is a common
object, inherited from the MIB framework used to provide a
common management interface to all the Cabletron Routing Services
protocol-specific MIBs.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.2.2.1.1.23 |
nwAppnFwdLinks OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3 |
nwAppnFwdLsConfig OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.1 |
nwAppnFwdLsTableThis table contains the configuration and management
information for links to adjacent link stations. This table is
indexed by nwAppnFwdLsName. Operations which apply are add,
delete, modify, enable, and disable. To add a row to the
table, the required fields in the row must be provided.
The required fields are nwAppnFwdLsPortName and
nwAppnFwdLsDestAddr. All other fields which are not provided
will be defaulted. To enable a link select enable(3) from
nwAppnFwdLsAdminStatus. To delete a row, set nwAppnFwdLsControl
to delete(3). To disable a link set nwAppnFwdLsStopType and
then select disable(2) in nwAppnFwdLsAdminStatus.
If nwAppnFwdLsStopType is not selected, the link is disabled in
an orderly fashion. SEQUENCE OF NwAppnFwdLsEntry .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.1.1 |
nwAppnFwdLsEntrySpecifies the configuration for a link to an adjacent link
station for which the entry exists. NwAppnFwdLsEntry .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.1.1.1 |
nwAppnFwdLsNameSpecifies the primary index to the adjacent link station table
(nwAppnFwdLsTable).rw DisplayString .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.1.1.1.1 |
nwAppnFwdLsAdminStatusSets the administrative state of a link to an adjacent
link station. enabled(3) causes the link to become established.
disable(2) causes the link to terminate. There are various
severities of disabling a link which are selected via the leaf
node nwAppnFwdLsStopType described further within this branch.rw Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.1.1.1.2 |
nwAppnFwdLsOperStatusSpecifies the current operating status of the link for which this
entry exists.ro Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.1.1.1.3 |
nwAppnFwdLsOperationalTimeSpecifies the elapsed time, in hundredths of a second, that
nwAppnFwdLsAdminStatus has been either enabled or DISABLED.
If the operational state is pending-disable,
nwAppnFwdLsOperationalTime indicates the amount of time since
the state was enabled. If the operational state is pending-enable,
nwAppnFwdLsOperationalTime indicates the amount of time since the
state was DISABLED.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.1.1.1.4 |
nwAppnFwdLsControlSet this object to delete in order to delete the entry.rw Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.1.1.1.5 |
nwAppnFwdLsPortNameThis link station port name corresponds to the port name
index into the the nwAppnExtensionTable which describes the
router port on which the adjacent link station is defined.rw DisplayString .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.1.1.1.6 |
nwAppnFwdLsAdjCpNameSpecifies the fully-qualified, 17 byte long, adjacent Control
Point name. The name format is NNNNNNNN.CCCCCCCC where NNNNNNNN
is the network identifier and CCCCCCCC is the Control Point name.
Valid characters to make up these two strings are uppercase
letters A through Z, numerics 0 through 9, and the special
characters $, # and @. The first character of the name must NOT
be numeric. Each string must be a maximum length of 8 characters
with no embedded spaces and the strings are joined by a dot.rw DisplayString .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.1.1.1.7 |
nwAppnFwdLsAdjCpTypeSpecifies the adjacent node type. The following values are
valid: endnode(1), networknode(2). endnode(1) includes both
End Node and LEN node types.rw Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.1.1.1.8 |
nwAppnFwdLsAutoActSupportSpecifies whether the link is automatically enabled when
a session is activated over the link. It is an error to set
this to yes(1) when nwAppnFwdLsCpCpSessSupp is set to yes(1).rw Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.1.1.1.10 |
nwAppnFwdLsLimitedRsrcSpecifies whether this link is to be deactivated when
there are no sessions using the link. If
nwAppnFwdLsCpCpSessSupp is yes, however, the link will
not be deactivated if CP-CP sessions are terminated.
Note also that a link over a non-switched port cannot
be configured as a limited resource.rw Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.1.1.1.11 |
nwAppnFwdLsSscpSessionRequests a host system to initiate sessions between its SSCP and
dependent LUs within APPN Routing Services. If set to yes,
then nwAppnFwdLsPuName is required. Note: once this parameter
is set along with other link station parameters associated with
a link station definition, it cannot be modified. In order to
change it, the link station definition itself must be deleted and
then redefined with the new parameter.rw Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.1.1.1.12 |
nwAppnFwdLsPuNameSpecifies the name of the local PU if nwAppnFwdLsSscpSession is
set to yes. Valid characters are uppercase A through Z and
numerics 0 through 9. The name must start with an alphabetic
character. Note: once this parameter is set along with other
link station parameters associated with a link station definition,
it cannot be modified. In order to change it, the link station
definition itself must be deleted and then redefined with the new
parameter.rw DisplayString .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.1.1.1.13 |
nwAppnFwdLsBackLvlLenENSpecifies whether or not the adjacent node is a back level
LEN Node. If so, specify the type of back level LEN node as
follows:
xid3(2) - supports XID-3 protocols, but does not include
Network Name control vector in the XID.
xid0(3) - Supports XID-0 protocols. Not valid if
nwAppnExtIfLocalLsRole is negotiable(1).
noxid(4) - Does not support XID protocols. Valid only if
nwAppnExtIfPortType is nonswitched(1) and not
valid if nwAppnExtIfLocalLsRole is negotiable(1).
If not no(1), then nwAppnFwdLsAdjCpName and nwAppnFwdLsIdNum
must be specified.rw Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.1.1.1.14 |
nwAppnFwdLsCpCpSessSuppSpecifies whether this link supports CP to CP sessions.rw Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.1.1.1.16 |
nwAppnFwdLsEffectCapSpecifies th maximum kilo bits per second rate (link speed)
for the link.rw INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.1.1.1.17 |
nwAppnFwdLsConnectCostSpecifies the cost per connect time for the link. Zero is the
lowest cost and 255 is the largest cost.rw INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.1.1.1.18 |
nwAppnFwdLsByteCostSpecifies the cost per Byte for the link. Zero is the lowest
cost and 255 is the largest cost.rw INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.1.1.1.19 |
nwAppnFwdLsSecuritySecurity selections available for the link are as follows:
non-secure - specifies no security.
public switched - data flows over a public switched
network.
underground cable - data transmitted over a secure
underground cable.
secure conduit - line is secure conduit that is not
guarded.
guarded conduit - conduit that is protected against
physical tapping.
encrypted - encryption over the line.
guarded radiation - line is proected against physical
and radiation tapping.rw Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.1.1.1.20 |
nwAppnFwdLsPropDelaySpecifies the propagation delay which represents the relative
time it takes for a signal to travel the length of the link in
microseconds, with some of the more common default values
enumerated. The default times in parentheses are in microseconds.
These default values fall into the following ranges:
minimum - no propagation delay
negligible, lan - less than 480 microseconds
terrestrial, telephone - between 480 and 49,512
microseconds
packetswitched - between 49,512 and 245,760
microseconds
long, satellite - more than 245760 microseconds.
maximum - the maximum propagation delay.rw Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.1.1.1.21 |
nwAppnFwdLsUsrDef1Specifies user defined parameter 1.rw INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.1.1.1.22 |
nwAppnFwdLsUsrDef2Specifies user defined parameter 2.rw INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.1.1.1.23 |
nwAppnFwdLsUsrDef3Specifies user defined parameter 3.rw INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.1.1.1.24 |
nwAppnFwdLsTrgtPacingCountSpecies the desired pacing window size for BINDs on this
transmission group. The number is a value between 0 and 32767
and is significant only when fixed bind pacing is being used.rw INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.1.1.1.25 |
nwAppnFwdLsMaxSendBtuSpecifies maximum Message Unit (MU) size that can be sent.rw INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.1.1.1.26 |
nwAppnFwdLsNumActiveSessionSpecifies total number of active sessions on this link.
This includes both end point sessions and intermediate sessions.ro INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.1.1.1.27 |
nwAppnFwdLsdynamicLsSpecifies whether this link station was dynamically
allocated (yes(1)) or whether the link station was defined by
the user (no(2)).ro Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.1.1.1.28 |
nwAppnFwdLsStopTypeSpecifies the type of shutdown for a link. Once selected,
set disable in nwAppnFwdIfAdminStatus. The shutdown choices are
as follows:
immediate(1) causes the link station to disconnect
immediately without flushing remaining Message Unit (MU)s.
orderly(2) causes the link station to disconnect
after successfully flushing remaining Message Unit (MU)s.rw Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.1.1.1.29 |
nwAppnFwdLsPortNbrThis link station port number corresponds to the index into
the nwAppnFwdIfTable and the nwAppnExtensionTable, which
together describe the port used by APPN Routing Services.ro INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.1.1.1.30 |
nwAppnFwdLsDestAddrSpecifies the destination address of the adjacent link station
depending on the media type. For token ring or ethernet ports,
the information is the 6 byte Destination MAC Address which
starts in byte 1 and ends in byte 6. For token ring ports,
the MAC address must be specified in non-canonical format.
For ethernet ports the MAC address must be specified in
canonical format. For frame relay, the address is a non-null
terminated string which is the ascii representation of the DLCI.rw OCTET STRING .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.1.1.1.31 |
nwAppnFwdLsDsapFor a token ring or ethernet network, specifies the destination
SAP address associated with the adjacent link station.rw OCTET STRING .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.1.1.1.32 |
nwAppnFwdLsBlockNumThis represents the 3 hexadecimal digit block number which
precedes the 5 digit id number in the 8 digit node id of the
adjacent node. The node id is used in XIDs and Alerts. The
block number identifies the product type. Both the block number
and id number combined, uniquely identify the adjacent node
within the installation network.rw DisplayString .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.1.1.1.33 |
nwAppnFwdLsIdNumThis represents the 5 hexadecimal digit id number which follows
the 3 digit block number in the 8 digit node id of the adjacent
node. The node id is used in XIDs and Alerts. The id number
uniquely identifies the adjacent node within a product type
indicated by its block number. Both the block number and id number
combined, uniquely identify the adjacent node within the
installation network.rw DisplayString .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.1.1.1.34 |
nwAppnFwdLsCounters OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.2 |
nwAppnFwdLsCtrTableThis table contains the Basic Link Unit (BLU) and byte
counters for each configured adjacent link station. SEQUENCE OF NwAppnFwdLsCtrEntry .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.2.1 |
nwAppnFwdLsCtrEntryEach entry indicates the Basic Link Unit (BLU) and byte
count for the configured adjacent link station for which the
entry exists. NwAppnFwdLsCtrEntry .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.2.1.1 |
nwAppnFwdLsCtrLsNameSpecifies the primary index into the link station
counter table. This index is the link station name.ro DisplayString .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.2.1.1.1 |
nwAppnFwdLsCtrAdminStatusSets the administrative state of the Basic Link Unit (BLU)
and byte counters on the link for which this entry exists.
enabled(3) causes these counters to reset and become active.
disabled(2) causes these counters to become inactive.rw Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.2.1.1.2 |
nwAppnFwdLsCtrResetResets the Basic Link Unit (BLU) and byte counters on the link
for which this entry exists. reset(2) resets the counters to 0.
nwAppnFwdLsCtrOperationalTime is also reset to 0.rw Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.2.1.1.3 |
nwAppnFwdLsCtrOperationalTimeSpecifies the amount of time in hundreths of a second that the
Basic Link Unit (BLU) and byte counters have been active on the
link for which this entry exists.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.2.1.1.4 |
nwAppnFwdLsCtrInBlusSpecifies the total number of Basic Link Unit (BLU)s that have
been received, during nwAppnFwdLsCtrOperationaltime, on the link
for which this entry exists. This includes both information
(I-frame) and XID BLUs.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.2.1.1.5 |
nwAppnFwdLsCtrOutBlusSpecifies the total number of Basic Link Unit (BLU)s that have
been transmitted, during nwAppnFwdLsCtrOperationalTime, on the
link for which this entry exists. This includes both information
(I-frame) and XID BLUs.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.2.1.1.6 |
nwAppnFwdLsCtrFwdBlusThis object does not apply to this protocol. It is a common
object, inherited from the MIB framework used to provide a
common management interface to all the Cabletron Routing Services
protocol-specific MIBs.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.2.1.1.7 |
nwAppnFwdLsCtrFilteredBlusThis object does not apply to this protocol. It is a common
object, inherited from the MIB framework used to provide a
common management interface to all the Cabletron Routing Services
protocol-specific MIBs.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.2.1.1.8 |
nwAppnFwdLsCtrDiscardBlusThis object does not apply to this protocol. It is a common
object, inherited from the MIB framework used to provide a
common management interface to all the Cabletron Routing Services
protocol-specific MIBs.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.2.1.1.9 |
nwAppnFwdLsCtrAddrErrBlusThis object does not apply to this protocol. It is a common
object, inherited from the MIB framework used to provide a
common management interface to all the Cabletron Routing Services
protocol-specific MIBs.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.2.1.1.10 |
nwAppnFwdLsCtrLenErrBlusSpecifies the total number of received Basic Link Unit (BLU)s
during nwAppnFwdLsCtrOperationalTime which have invalid DLC
headers on the link for which this entry exists.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.2.1.1.11 |
nwAppnFwdLsCtrHdrErrBlusSpecifies the total number of received Basic Link Unit (BLU)s
during nwAppnFwdLsCtrOperationalTime which have length errors
on the link for which this entry exists.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.2.1.1.12 |
nwAppnFwdLsCtrInBytesSpecifies the total number of bytes that have been received,
during nwAppnFwdLsCtrOperationalTime, on the link for which
the entry exists. This includes bytes contained in
information (I-frames) and XID BLUs.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.2.1.1.13 |
nwAppnFwdLsCtrOutBytesSpecifies the total number of bytes that have been transmitted,
during nwAppnFwdLsCtrOperationalTime, on the link for which the
entry exists. This includes bytes contained in information
(I-frames) and XID BLUs.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.2.1.1.14 |
nwAppnFwdLsCtrFwdBytesThis object does not apply to this protocol. It is a common
object, inherited from the MIB framework used to provide a
common management interface to all the Cabletron Routing Services
protocol-specific MIBs.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.2.1.1.15 |
nwAppnFwdLsCtrFilteredBytesThis object does not apply to this protocol. It is a common
object, inherited from the MIB framework used to provide a
common management interface to all the Cabletron Routing Services
protocol-specific MIBs.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.2.1.1.16 |
nwAppnFwdLsCtrDiscardBytesThis object does not apply to this protocol. It is a common
object, inherited from the MIB framework used to provide a
common management interface to all the Cabletron Routing Services
protocol-specific MIBs.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.2.1.1.17 |
nwAppnFwdLsCtrHostInBlusThis object does not apply to this protocol. It is a common
object, inherited from the MIB framework used to provide a
common management interface to all the Cabletron Routing Services
protocol-specific MIBs.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.2.1.1.18 |
nwAppnFwdLsCtrHostOutBlusThis object does not apply to this protocol. It is a common
object, inherited from the MIB framework used to provide a
common management interface to all the Cabletron Routing Services
protocol-specific MIBs.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.2.1.1.19 |
nwAppnFwdLsCtrHostDiscardBlusThis object does not apply to this protocol. It is a common
object, inherited from the MIB framework used to provide a
common management interface to all the Cabletron Routing Services
protocol-specific MIBs.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.2.1.1.20 |
nwAppnFwdLsCtrHostInBytesThis object does not apply to this protocol. It is a common
object, inherited from the MIB framework used to provide a
common management interface to all the Cabletron Routing Services
protocol-specific MIBs.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.2.1.1.21 |
nwAppnFwdLsCtrHostOutBytesThis object does not apply to this protocol. It is a common
object, inherited from the MIB framework used to provide a
common management interface to all the Cabletron Routing Services
protocol-specific MIBs.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.2.1.1.22 |
nwAppnFwdLsCtrHostDiscardBytesThis object does not apply to this protocol. It is a common
object, inherited from the MIB framework used to provide a
common management interface to all the Cabletron Routing Services
protocol-specific MIBs.ro Counter .1.3.6.1.4.1.52.4.2.2.2.3.5.2.2.3.2.1.1.23 |
nwAppnTopology OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.4 |
nwAppnDistanceVector OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.4.1 |
nwAppnLinkState OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.4.2 |
nwAppnIsr OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.4.2.1 |
nwAppnIsrSystem OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.4.2.1.1 |
nwAppnIsrConfig OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.4.2.1.1.1 |
nwAppnIsrAdminStatusIntermediate Session Routing cannot be turned on and
off. Any modifications to this leaf will have no
affect.rw Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.5.2.4.2.1.1.1.1 |
nwAppnIsrOperStatusSpecifies the current operating condition of the ISR routing
protocol, system-wide.ro Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.5.2.4.2.1.1.1.2 |
nwAppnIsrAdminResetThis object does not apply to this protocol. It is a common
object, inherited from the MIB framework used to provide a
common management interface to all the Cabletron Routing Services
protocol-specific MIBs.ro Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.5.2.4.2.1.1.1.3 |
nwAppnIsrOperationalTimeIndicates the elapsed time, in hundredths of a second, that
nwAppnOperStatus has been in its current state.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.52.4.2.2.2.3.5.2.4.2.1.1.1.4 |
nwAppnIsrVersionIndicates the current revision level of the ISR firmware in
textual format. This is the same version number as that of APPN
Routing Services firmware, nwAppnSysVersion.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.52.4.2.2.2.3.5.2.4.2.1.1.1.5 |
nwAppnIsrCounters OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.4.2.1.1.2 |
nwAppnIsrInterfaces OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.4.2.1.2 |
nwAppnIsrIfConfig OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.4.2.1.2.1 |
nwAppnIsrIfCounters OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.4.2.1.2.2 |
nwAppnIsrDatabase OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.4.2.1.3 |
nwAppnIsrFilters OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.4.2.1.4 |
nwAppnFib OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.5 |
nwAppnEndSystems OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.6 |
nwAppnHostsSystem OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.6.1 |
nwAppnHostsInterfaces OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.6.2 |
nwAppnAccessControl OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.7 |
nwAppnFilters OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.8 |
nwAppnRedirector OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.9 |
nwAppnEvent OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.10 |
nwAppnEventLogConfig OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.10.1 |
nwAppnEventAdminStatusSet the administrative state of APPN Routing Services event
logging. enabled(3) causes the event log to become active.
disabled(2) causes the event log to become inactive.rw Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.5.2.10.1.1 |
nwAppnEventMaxEntriesSets the maximum number of entries allowed in the event log
table. When the number of entries reaches the value of
nwAppnEventMaxEntries the first (oldest) entry is deleted
to allow a new entry to be added.rw INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.10.1.2 |
nwAppnEventTraceAllenabled(3) allows logging of all event types on all ports.
disabled(2) causes the filter table to specify which events to
log.rw Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.5.2.10.1.3 |
nwAppnEventLogFilterTable OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.10.2 |
nwAppnEventFilterTableThis table contains descriptions of how to filter log entries. SEQUENCE OF NwAppnEventFilterEntry .1.3.6.1.4.1.52.4.2.2.2.3.5.2.10.2.1 |
nwAppnEventFilterEntryEach entry specifies the filter for log entries. The
instance nwAppnEventProtocol refers to the instance used
in the nwRtgProtocolTable and nwComponentTable specified
by the ctrouter-mib.txt. NwAppnEventFilterEntry .1.3.6.1.4.1.52.4.2.2.2.3.5.2.10.2.1.1 |
nwAppnEventFltrProtocolSelects the protocol to log events from.ro INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.10.2.1.1.1 |
nwAppnEventFltrIfNumSpecifies the APPN Routing Services port on which to log events.ro INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.10.2.1.1.2 |
nwAppnEventFltrControlSetting this field to delete will allow entries to be
removed from the table. This is done by adding new entries
with instance fields that match the entry to be removed from
the table. The new entry being added must have this control
field set to delete in order for the matching entry already
in the table to be deleted. Setting this field to add will
add the entry to the table.rw Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.5.2.10.2.1.1.3 |
nwAppnEventFltrTypeThis bit field mask filter will allow only events of
certain types to be logged. By default all types will be
logged. Clearing event types from this field will cause
those types not to be logged. Adding event types to this
field will enable those types to be logged.rw Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.5.2.10.2.1.1.4 |
nwAppnEventFltrSeverityThis filter controls the amount of logging by ignoring events
of lower priority than that specified by the filter value.
Specifying highest(1) causes all events except those of highest
severity to be ignored. Specifying highmed(2) causes lowest
severity events to be ignored. Specifying highlow(3) causes
all events to be logged. highmed(2) is the default setting.rw Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.5.2.10.2.1.1.5 |
nwAppnEventFltrActionThis field specifies how the events are to be logged.
Specifying log(1) stores the events in the event log
table (defined below). Specifying trap(2) sends events
out through the trap mechanism. Specifying logTrap(3)
does both.rw Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.5.2.10.2.1.1.6 |
nwAppnEventLogTable OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.10.3 |
nwAppnEventTableThis table contains all events that have been logged. SEQUENCE OF NwAppnEventEntry .1.3.6.1.4.1.52.4.2.2.2.3.5.2.10.3.1 |
nwAppnEventEntryEach entry specifies events that have been logged. NwAppnEventEntry .1.3.6.1.4.1.52.4.2.2.2.3.5.2.10.3.1.1 |
nwAppnEventNumberThis ordinal number uniquely identifies events.ro INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.10.3.1.1.1 |
nwAppnEventTimeThis number specifies when the event was logged.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.52.4.2.2.2.3.5.2.10.3.1.1.2 |
nwAppnEventTypeSpecifies type of event logged.ro Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.5.2.10.3.1.1.3 |
nwAppnEventSeveritySpecifies the severity of the event logged.ro Enumeration .1.3.6.1.4.1.52.4.2.2.2.3.5.2.10.3.1.1.4 |
nwAppnEventProtocolSpecifies the protocol where the event occured.ro INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.10.3.1.1.5 |
nwAppnEventIfNumSpecifies the APPN Routing Services port the event occurred on.ro INTEGER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.10.3.1.1.6 |
nwAppnEventTextStringSpecifies the actual text string to be logged.ro OCTET STRING .1.3.6.1.4.1.52.4.2.2.2.3.5.2.10.3.1.1.7 |
nwAppnWorkGroup OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.2.2.2.3.5.2.11 |