CTRON-COMMON-MIB
Detailed view of the defined objects, syntax rules, and hierarchical paths.
112
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
112 total| Object Name |
|---|
deviceTypeThe type of management board.ro Enumeration .1.3.6.1.4.1.52.1.1.1.1 |
deviceNameA textual description on the entity managed by the
resident agent. It is mandatory that this only con-
tain printable ASCII characters.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.52.1.1.1.2 |
deviceIPAddressThe Network address, in this case the IP address,
of the device. This object is required for use by
the Local Management Interface.rw NetworkAddress .1.3.6.1.4.1.52.1.1.1.3 |
deviceTimeThe current time of day, in 24 hour format, as
measured by the device. The representation shall
use the standard HHMMSS format.rw DisplayString .1.3.6.1.4.1.52.1.1.1.4 |
deviceDateThe current date, as measured by the device. The
representation shall use the standard MMDDYYYY
format.rw DisplayString .1.3.6.1.4.1.52.1.1.1.5 |
fnb2 OBJECT IDENTIFIER .1.3.6.1.4.1.52.1.6.1.2 |
RFC1213-MIB Unknown .1.3.6.1.4.1.52.1.6.1.2 |
fnbTR OBJECT IDENTIFIER .1.3.6.1.4.1.52.1.6.1.2.1 |
fnbTRTableA list of entries that provide connection status of
Token Ring subsystems, for the FNB. SEQUENCE OF FnbTREntry .1.3.6.1.4.1.52.1.6.1.2.1.1 |
fnbTREntryAn entry in the fnbTRTable containing objects that
provide FNB connection status for a Token Ring sub-
system. FnbTREntry .1.3.6.1.4.1.52.1.6.1.2.1.1.1 |
fnbTRIndexAn unique value for each Token Ring subsystem. Its
value ranges between 1 and chassisSlots. The value
for each interface must remain constant, at least,
from one re-initialization of the entity's network
management system to the next re-initialization.ro INTEGER .1.3.6.1.4.1.52.1.6.1.2.1.1.1.1 |
fnbConnectLeftThe Connected Left board (board n + 1) has the following
states:
Detached == 1 (Management (only management) detached,
read/write).
Attached == 2 (Management/AutoMode attached, read/write).
Faulted == 3 (Management/AutoMode tried to attach but
failed READ ONLY).rw Enumeration .1.3.6.1.4.1.52.1.6.1.2.1.1.1.2 |
fnbConnectRightThe Connected Right board (board n - 1) has the following states:
Detached == 1 (Management (only management) detached, read/write).
Attached == 2 (Management/AutoMode attached, read/write ).
Faulted == 3 (Management/AutoMode tried to attach but failed,
READ ONLY).rw Enumeration .1.3.6.1.4.1.52.1.6.1.2.1.1.1.3 |
fnbBypassDenotes the bypass status of the current Token Ring
board. Bypassed means the board is NOT attached to the
FNB.rw Enumeration .1.3.6.1.4.1.52.1.6.1.2.1.1.1.4 |
fnbRPBypassDenotes the Ring Port bypass status of the current Token Ring
board. If this capability is not available on this board, the
value 'other' is returned when read, and BADSETINFO when written.rw Enumeration .1.3.6.1.4.1.52.1.6.1.2.1.1.1.5 |
fnbCSMACD OBJECT IDENTIFIER .1.3.6.1.4.1.52.1.6.1.2.2 |
fnbCSMACDTableA list of entries that provide connection status of
CSMA/CD subsystems, for the FNB. SEQUENCE OF FnbCSMACDEntry .1.3.6.1.4.1.52.1.6.1.2.2.1 |
fnbCSMACDEntryAn entry in the fnbCSMACDTable containing objects
that provide FNB connection status for a CSMA/CD
subsystem. FnbCSMACDEntry .1.3.6.1.4.1.52.1.6.1.2.2.1.1 |
fnbCSMACDIndexAn unique value for each CSMACD subsystem. Its
value ranges between 1 and chassisSlots. The value
for each interface must remain constant, at least,
from one re-initialization of the entity's network
management system to the next re-initialization.rw INTEGER .1.3.6.1.4.1.52.1.6.1.2.2.1.1.1 |
fnbConnectDenotes the connection status of the CSMA/CD board
to the inter-RIC bus.rw Enumeration .1.3.6.1.4.1.52.1.6.1.2.2.1.1.2 |
fnbPortChangesDenotes the number of times any port on the
given MIM has changed it's connection to the
inter-RIC bus.ro Counter .1.3.6.1.4.1.52.1.6.1.2.2.1.1.3 |
fnbPortConnect OBJECT IDENTIFIER .1.3.6.1.4.1.52.1.6.1.2.3 |
fnbPortConnectTableThis table is used to control port
association on ethernet devices. Only
those boards that support port switching
will be listed in this table. SEQUENCE OF FnbPortConnectEntry .1.3.6.1.4.1.52.1.6.1.2.3.1 |
fnbPortConnectEntryDescribes a specific port connection entry. FnbPortConnectEntry .1.3.6.1.4.1.52.1.6.1.2.3.1.1 |
fnbPortConnectBoardIndexAn instance of a board for which this port
assignment relationship exists.ro INTEGER .1.3.6.1.4.1.52.1.6.1.2.3.1.1.1 |
fnbPortConnectPortIndexAn instance of a port for which this
assignment relationship exists.ro INTEGER .1.3.6.1.4.1.52.1.6.1.2.3.1.1.2 |
fnbPortConnectPortAssignmentThe specific channel that the port is
assigned.rw Enumeration .1.3.6.1.4.1.52.1.6.1.2.3.1.1.3 |
fnbPortConnectCompIDThis is the component ID as defined in the chassis
MIB that this port is associated with. These
components will be repeater components.ro INTEGER .1.3.6.1.4.1.52.1.6.1.2.3.1.1.4 |
fnbPortConnectionChangesMaintains the number of times any port within
the mangement domain of this MIM changes it's
port assignment.ro Counter .1.3.6.1.4.1.52.1.6.1.2.3.2 |
chassis OBJECT IDENTIFIER .1.3.6.1.4.1.52.1.6.1.3 |
chassisHWRevDefine the hardware revision of the device or sys-
tem chassis.ro INTEGER .1.3.6.1.4.1.52.1.6.1.3.1 |
chassisTypeDenotes the type of chassis.ro Enumeration .1.3.6.1.4.1.52.1.6.1.3.2 |
chassisSlotsDenotes the number of available chassis slots.ro INTEGER .1.3.6.1.4.1.52.1.6.1.3.3 |
chassisFNBDenotes the presence or absence of the FNB.ro Enumeration .1.3.6.1.4.1.52.1.6.1.3.4 |
chassisAlarmEnaAllow an audible alarm to be either enabled or dis-
abled.rw Enumeration .1.3.6.1.4.1.52.1.6.1.3.5 |
chassisAlarmStateDenotes the current condition of the power supply
fault detection circuit. Setting a value of
chassisNoFaultCondition(1) disables the current
chassis alarm condition, and stops the current
audible alarm from sounding. Setting a value of
chassisFaultCondition(2) is not allowed.
This object will read with the value of
chassisNoFaultCondition(1) when the chassis is
currently operating with no power faults detected.
This object will read with the value of
chassisFaultCondition(2) when the chassis is
currently in a power fault condition.rw Enumeration .1.3.6.1.4.1.52.1.6.1.3.6 |
environment OBJECT IDENTIFIER .1.3.6.1.4.1.52.1.6.1.4 |
powerTableA list of power supply entries. SEQUENCE OF PowerEntry .1.3.6.1.4.1.52.1.6.1.4.1 |
powerEntryAn entry in the powerTable providing objects for a
power supply. PowerEntry .1.3.6.1.4.1.52.1.6.1.4.1.1 |
powerSupplyNumDenotes the power supply that may have failed.ro INTEGER .1.3.6.1.4.1.52.1.6.1.4.1.1.1 |
powerSupplyStateDenotes the power supply's state.ro Enumeration .1.3.6.1.4.1.52.1.6.1.4.1.1.2 |
powerSupplyIdIdentifies the type of power supply. For example, this
could be used to identify power supplies which support
additional remote management capabilities.ro OBJECT IDENTIFIER .1.3.6.1.4.1.52.1.6.1.4.1.1.3 |
powerSupplyRedunIdentifies whether power redundancy is available
within the chassis.
Devices that do not support power supply redundancy,
will return infoNotAvailable.ro Enumeration .1.3.6.1.4.1.52.1.6.1.4.1.1.4 |
powerSupplyRemoteDisableProvides Enable/Disable control of the power supply.
For devices that do not support this capability, a set
attempt will return BADVALUE, and a read will always
return infoNotAvailable.rw Enumeration .1.3.6.1.4.1.52.1.6.1.4.1.1.5 |
nB55 OBJECT IDENTIFIER .1.3.6.1.4.1.52.1.6.2.3 |
nB55HWAddressThe device's MAC address.ro PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.52.1.6.2.3.1 |
nB55HWRevDenotes the revision of the nB55 board. A value of
one denotes Revision 1, a value of two denotes Revi-
sion 2, and so on.ro INTEGER .1.3.6.1.4.1.52.1.6.2.3.2 |
nB55FWRevDenotes the revision of firmware in the module.
The first octets provides the version, and the
second provides the revision.ro OCTET STRING .1.3.6.1.4.1.52.1.6.2.3.3 |
mRXI OBJECT IDENTIFIER .1.3.6.1.4.1.52.1.6.2.6 |
mRXIHWAddressThe device's MAC address.ro PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.52.1.6.2.6.1 |
mRXIHWRevDenotes the revision of the mRXI board. A value of
one denotes Revision 1, a value of two denotes Revi-
sion 2, and so on.ro INTEGER .1.3.6.1.4.1.52.1.6.2.6.2 |
mRXIFWRevDenotes the revision of firmware in the module.
The first octets provides the version, and the
second provides the revision.ro OCTET STRING .1.3.6.1.4.1.52.1.6.2.6.3 |
iRM3 OBJECT IDENTIFIER .1.3.6.1.4.1.52.1.6.2.7 |
iRM3HWAddressThe device's MAC address.ro PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.52.1.6.2.7.1 |
iRM3HWRevDenotes the revision of the IRM3 board. A value of
one denotes Revision 1, a value of two denotes Revi-
sion 2, and so on.ro INTEGER .1.3.6.1.4.1.52.1.6.2.7.2 |
iRM3FWRevDenotes the revision of firmware in the module.
The first octets provides the version, and the
second provides the revision.ro OCTET STRING .1.3.6.1.4.1.52.1.6.2.7.3 |
iRM3PortAssocControls how front panel ports are associated
with the Irm3.rw Enumeration .1.3.6.1.4.1.52.1.6.2.7.4 |
iRM3BPSupportDenotes whether or not Backplane Protocol Support is
present in the current version of the IRM3.ro Enumeration .1.3.6.1.4.1.52.1.6.2.7.5 |
tRMM OBJECT IDENTIFIER .1.3.6.1.4.1.52.1.6.2.8 |
tRMMHWAddressThe device's MAC address.ro PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.52.1.6.2.8.1 |
tRMMHWRevDenotes the revision of the tRMM board. A value of
one denotes Revision 1, a value of two denotes Revi-
sion 2, and so on.ro INTEGER .1.3.6.1.4.1.52.1.6.2.8.2 |
tRMMFWRevDenotes the revision of firmware in the module.
The first octets provides the version, and the
second provides the revision.ro OCTET STRING .1.3.6.1.4.1.52.1.6.2.8.3 |
eMME OBJECT IDENTIFIER .1.3.6.1.4.1.52.1.6.2.9 |
eMMEHWAddressThe device's MAC address.ro PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.52.1.6.2.9.1 |
eMMEHWRevDenotes the revision of the eMME board. A value of
one denotes Revision 1, a value of two denotes Revi-
sion 2, and so on.ro INTEGER .1.3.6.1.4.1.52.1.6.2.9.2 |
eMMEFWRevDenotes the revision of firmware in the module.
The first octets provides the version, and the
second provides the revision.ro OCTET STRING .1.3.6.1.4.1.52.1.6.2.9.3 |
eMMEBoardMapDenotes a bit encoded representation of the slots that
contain MIM boards. If a bit is a one then the board
is present.ro INTEGER .1.3.6.1.4.1.52.1.6.2.9.4 |
fPRedundancy OBJECT IDENTIFIER .1.3.6.1.4.1.52.1.6.2.10 |
fPRedund OBJECT IDENTIFIER .1.3.6.1.4.1.52.1.6.2.10.1 |
fPRedundResetIf this object is set to Reset it will cause a reset
of the front panel redundancy. Setting this object to
NoReset will do nothing. This object will always be
read as NoReset.rw Enumeration .1.3.6.1.4.1.52.1.6.2.10.1.1 |
fPRedundPollIntervalGet/Set the number of seconds between polls for front
panel redundancy.rw INTEGER .1.3.6.1.4.1.52.1.6.2.10.1.2 |
fPRedundRetrysGet/Set the the number of unanswered polls allowed for
the front panel redundancy before it switches ports.rw INTEGER .1.3.6.1.4.1.52.1.6.2.10.1.3 |
fPRedundNumAddrGet the number of IP Addresses associated with front panel
redundancy.ro INTEGER .1.3.6.1.4.1.52.1.6.2.10.1.4 |
fPRedundAddAddrAdd an IP Address to the polling list for the front panel
redundancy.rw NetworkAddress .1.3.6.1.4.1.52.1.6.2.10.1.5 |
fPRedundDelAddrDelete an IP Address from the polling list for the
front panel redundancy.rw NetworkAddress .1.3.6.1.4.1.52.1.6.2.10.1.6 |
fPRedundActivePortGet/Set the front panel port you want to be active
when front panel redundancy is enabled.rw INTEGER .1.3.6.1.4.1.52.1.6.2.10.1.7 |
fPRedundEnableIf this object is set to enable, the front panel
redundancy will be activated. If this object is set
to disable, the front panel redundancy will be
deactivated. When read, this object will returns the
state of the object based on the last request
made.rw Enumeration .1.3.6.1.4.1.52.1.6.2.10.1.8 |
fPRedundAddrTableA list of entries that provide IP address
information for front panel redundancy. SEQUENCE OF FPRedundAddrEntry .1.3.6.1.4.1.52.1.6.2.10.2 |
fPRedundAddrEntryAn entry in the fPRedundAddrTable providing objects
for front panel redundancy. FPRedundAddrEntry .1.3.6.1.4.1.52.1.6.2.10.2.1 |
fPRedundAddrIdA unique value identifying an element in a sequence of
member IP Addresses which belong to the front panel
redundancy. This value goes from 1 to the maximum
number of IP Addresses which may be included in
front panel redundancy.ro INTEGER .1.3.6.1.4.1.52.1.6.2.10.2.1.1 |
fPRedundAddrIPAddrReturns an IP Address associated with the front panel
redundancy.ro NetworkAddress .1.3.6.1.4.1.52.1.6.2.10.2.1.2 |
dlForceOnBootWhen set to a 1, the system will request a
download, during the next system restart.
If no server is found and the current image
in flash memory is valid, the system will boot
using the flash-resident image.rw INTEGER .1.3.6.1.4.1.52.1.6.4.1 |
dlCommitRAMToFlashWhen written with a 1, the boot software will erase
flash memory, compress the downloaded code, and save
the compressed image into flash memory. Upon com-
pletion of this operation, the flash memory driver
resets this object to 0, indicating completion of
the programming operation.rw INTEGER .1.3.6.1.4.1.52.1.6.4.2 |
dlInitiateColdBootWhen written with a 1, the boot software intiates a
system reboot. All MIB variables used to control
the exact nature of the download should be set,
prior to activating a system reset.
A read always returns a 0.rw INTEGER .1.3.6.1.4.1.52.1.6.4.3 |
dlTFTPRequestHostThe IP address of the server to be used, when
firmware is to be loaded across the network.rw NetworkAddress .1.3.6.1.4.1.52.1.6.4.4 |
dlTFTPRequestThe filename requested of the server, when firmware
is to be loaded across the network.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.52.1.6.4.5 |
dlLastImageFilenameFilename of the last image to be successfully
loaded into memory.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.52.1.6.4.6 |
dlLastServerIPAddressThe IP address of the server used to load the
present image in flash memory.ro NetworkAddress .1.3.6.1.4.1.52.1.6.4.7 |
dlFlashSizeDenotes the size, in bytes, of flash memory con-
tained on this module.ro INTEGER .1.3.6.1.4.1.52.1.6.4.8 |
dlFlashCountDenotes the number of times that flash memory has
been reprogrammed. This value is initialzed to 1,
when the module is initially powered up.ro INTEGER .1.3.6.1.4.1.52.1.6.4.9 |
dlFirmwareBaseDenotes the starting address of the firmware in
RAM.ro INTEGER .1.3.6.1.4.1.52.1.6.4.10 |
dlFirmwareTopDenotes the ending address of firmware in RAM.ro INTEGER .1.3.6.1.4.1.52.1.6.4.11 |
dlFirmwareStartDenotes the start address of the firmware, in RAM,
as established by the boot process.ro INTEGER .1.3.6.1.4.1.52.1.6.4.12 |
dlBootRevDenotes the revision of boot firmware in the module.
The first octets provides the version, and the
second provides the revision.ro OCTET STRING .1.3.6.1.4.1.52.1.6.4.13 |
dlForceBootpWhen set, this variable forces the client to send a
BOOTP request packet when rebooting. The client will
make several attempts before timing out if a server
does not respond. This variable stays set. When set to
a 1 it should always be read as a one. When set to zero
it should always be read as zero.rw INTEGER .1.3.6.1.4.1.52.1.6.4.14 |
dlServerNameThis OID is reserved for future use of the Bootp server
name. This field can be used when a client wants to get
boot information from a particular bootp server.rw OCTET STRING .1.3.6.1.4.1.52.1.6.4.15 |
dlOnLineDownLoadDuring normal operation this object has the value of 1. By
setting this object to a value of forceDownLoad(2) an online
download will be performed. By setting this object to a
value of forceDownLoadReset(3) an online down load will be
performed and a reset will be forced upon successful completion
of the download.rw Enumeration .1.3.6.1.4.1.52.1.6.4.16 |
dlOperStatusThis object reflects the status of the download code. A
value of normalOperation(3) reflects either a down load was
started but has finished normally and no reset was specified
or no down load has been started. A value of downLoadActive
only appears while a down load is in progress. A value of
downLoadCompleteError reflects that a down load was started
however an error was detected.ro Enumeration .1.3.6.1.4.1.52.1.6.4.17 |
dlNetAddressIP Address of the server to be used when an image is to be
downloaded using the Runtime TFTP Download.rw NetworkAddress .1.3.6.1.4.1.52.1.6.4.18 |
dlFileNameFilename requested of the server when an image is to be
downloaded using the Runtime TFTP Download. This should be a
complete path filename.rw OCTET STRING .1.3.6.1.4.1.52.1.6.4.19 |
dlErrorStringIf the value of ctDLOperStatus is downloadCompleteError(5)
then this object will provide a more complete description of
the error. Otherwise this object will be the zero length
string.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.52.1.6.4.20 |
dlTftpServerGatewayIPAddressThe IP address of the gateway/router which connects
this SNMP agent to the TFTP server.rw NetworkAddress .1.3.6.1.4.1.52.1.6.4.21 |
upsVersion OBJECT IDENTIFIER .1.3.6.1.4.1.21111.1.1.1 |
upsRevision OBJECT IDENTIFIER .1.3.6.1.4.1.21111.1.1.1.1 |
upsIDDenotes a type code which refers to the manufactur-
ers and model of the UPS.rw Enumeration .1.3.6.1.4.1.21111.1.1.1.1.1 |
upsUpTimeDenotes the operating time, in hours, since the UPS
was last powered on.ro INTEGER .1.3.6.1.4.1.21111.1.1.1.1.2 |
upsDisableAllows the UPS to be disabled. A set turns of the
UPS for those systems, so equipped. A get/get-next
always returns 0.rwdeprecated INTEGER .1.3.6.1.4.1.21111.1.1.1.1.3 |
upsDisconnectAllows the UPS backup power system to conserve its
battery. Setting the object to a value of 1 turns off
the power system. A get/get-next always retuns a 0.rw INTEGER .1.3.6.1.4.1.21111.1.1.1.1.4 |
upsTestDenotes the status performed on the UPS. A write
unitOK(1) intiates the test. A read indicates status of
test.rw Enumeration .1.3.6.1.4.1.21111.1.1.1.1.5 |
upsBatteryCapacityDenotes the percentage of battery capacity left,
100% being a fully-charged battery.ro INTEGER .1.3.6.1.4.1.21111.1.1.1.1.6 |
upsACLineVoltsInDenotes the input AC utility line voltage.ro INTEGER .1.3.6.1.4.1.21111.1.1.1.1.7 |
upsBatteryVoltsOutDenotes the battery voltage.ro INTEGER .1.3.6.1.4.1.21111.1.1.1.1.8 |