HM2-PLATFORM-SWITCHING-MIB
AI MIB Summary
HM2-PLATFORM-SWITCHING-MIB provides programmatic access to Layer 2 switching parameters and operational statistics for Hirschmann (Belden) Private Platform2 network switches. This module enables the monitoring of standard bridging metrics, including MAC address table entries, port state transitions, spanning tree protocol (STP) topology changes, and interface error counters.
The Hirschmann Private Platform2 MIB for Layer2 Switching. Copyright (C) 2011. All Rights Reserved.
Main OID:
hm2PlatformSwitching.1.3.6.1.4.1.248.12.1
474
Objects
Active
Status
8
Dependencies
Imported Objects
Objects
474 total| Object Name |
|---|
hm2PlatformSwitchingThe Hirschmann Private Platform2 MIB for Layer2 Switching.
Copyright (C) 2011. All Rights Reserved. MODULE-IDENTITY .1.3.6.1.4.1.248.12.1 |
hm2PlatformSwitchingTraps OBJECT IDENTIFIER .1.3.6.1.4.1.248.12.1.0 |
hm2PlatformStpInstanceNewRootTrapTrap is sent when this machine is a new STP Root when there is more
than one STP instance. NOTIFICATION-TYPE .1.3.6.1.4.1.248.12.1.0.10 |
hm2PlatformStpInstanceTopologyChangeTrapTrap is sent when there is a STP topology change when there is more
than one STP instance. NOTIFICATION-TYPE .1.3.6.1.4.1.248.12.1.0.11 |
hm2PlatformDaiIntfErrorDisabledTrapTrap is sent once an interface is error disabled by DAI when the
incoming packet rate exceeded configured rate limit during a
burst-interval. NOTIFICATION-TYPE .1.3.6.1.4.1.248.12.1.0.15 |
hm2PlatformStpInstanceLoopInconsistentStartTrapTrap is sent when this port in this STP instance enters
loop inconsistent state upon failure to receive a BPDU. NOTIFICATION-TYPE .1.3.6.1.4.1.248.12.1.0.16 |
hm2PlatformStpInstanceLoopInconsistentEndTrapTrap is sent when this port in this STP instance exits
loop inconsistent state upon reception of a BPDU. NOTIFICATION-TYPE .1.3.6.1.4.1.248.12.1.0.17 |
hm2PlatformDhcpSnoopingIntfErrorDisabledTrapTrap is sent once an interface is error disabled by DHCP Snooping when the
incoming packet rate exceeded configured rate limit during a
burst-interval. NOTIFICATION-TYPE .1.3.6.1.4.1.248.12.1.0.18 |
hm2PlatformStpCstBpduGuardTrapThis trap is sent if on this port when the BPDU guard
functionality is enabled (globally and for this port)
and a (R)STP BPDU is received on this port. That means when
hm2AgentStpCstPortBpduGuardEffect is set to enable(1) for this port.
Then ifAdminStatus for this port is set to down(2). NOTIFICATION-TYPE .1.3.6.1.4.1.248.12.1.0.248 |
hm2AgentConfigGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.12.1.2 |
hm2AgentLagConfigGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.12.1.2.2 |
hm2AgentLagConfigCreateAgent LAG Create.
When this object is set with a non-empty string with the format lag/<port>,
a new LAG will be created if possible, with the entered string as its
index.
Get operation on this MIB object returns a null-value, as
for the purpose of viewing the LAG index and details, the user should
perform the traversal of hm2AgentLagSummaryConfigTable. For
this reason the get operation on this object
hm2AgentLagConfigCreate becomes insignificant.rw DisplayString .1.3.6.1.4.1.248.12.1.2.2.1 |
hm2AgentLagSummaryConfigTableA summary table of the switch's LAG config entries SEQUENCE OF Hm2AgentLagSummaryConfigEntry .1.3.6.1.4.1.248.12.1.2.2.2 |
hm2AgentLagSummaryConfigEntrySwitch's LAG config entry Hm2AgentLagSummaryConfigEntry .1.3.6.1.4.1.248.12.1.2.2.2.1 |
hm2AgentLagSummaryLagIndexAgent LAG IfIndex.
This value corresponds with the LAG interface in the ifTable.ro Integer32 .1.3.6.1.4.1.248.12.1.2.2.2.1.1 |
hm2AgentLagSummaryNameAgent LAG Name.
The associated name of the LAG used during creation.rw DisplayString .1.3.6.1.4.1.248.12.1.2.2.2.1.2 |
hm2AgentLagSummaryFlushTimerAgent LAG FlushTimer.rwobsolete Integer32 .1.3.6.1.4.1.248.12.1.2.2.2.1.3 |
hm2AgentLagSummaryLinkTrapAgent LAG LinkTrap.
Configures sending Link Up/Down traps when the LAG interface goes Up or Down.rw HmEnabledStatus (HM2-TC-MIB) .1.3.6.1.4.1.248.12.1.2.2.2.1.4 |
hm2AgentLagSummaryAdminModeAgent LAG AdminMode.
Administratively enables or disables this LAG interface.rw HmEnabledStatus (HM2-TC-MIB) .1.3.6.1.4.1.248.12.1.2.2.2.1.5 |
hm2AgentLagSummaryStpModeAgent LAG StpMode
Administratively enables or disables STP on this interface.rw HmEnabledStatus (HM2-TC-MIB) .1.3.6.1.4.1.248.12.1.2.2.2.1.6 |
hm2AgentLagSummaryAddPortAgent LAG AddPort.
Set to a non 0 value to add a port to the LAG. Values correspond to
ifIndex values in the ifTable.
Note: agentPortType for the port to be added must be full duplex
and the same speed as previously added port(s), if any.rw Integer32 .1.3.6.1.4.1.248.12.1.2.2.2.1.7 |
hm2AgentLagSummaryDeletePortAgent LAG DeletePort.
Set to a non 0 value to remove a port from the LAG. Values correspond to
ifIndex values in the ifTable.rw Integer32 .1.3.6.1.4.1.248.12.1.2.2.2.1.8 |
hm2AgentLagSummaryStatusAgent LAG Status.
active(1) - This LAG is enabled.
destroy(6) - Set to this value to remove the LAG.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.248.12.1.2.2.2.1.9 |
hm2AgentLagSummaryTypeAgent LAG Type.
static(1) - This LAG is staticly maintained.
dynamic(2) - This LAG is dynamicly maintained.ro Enumeration .1.3.6.1.4.1.248.12.1.2.2.2.1.10 |
hm2AgentLagSummaryStaticCapabilityAgent LAG Static Capability
enable(1) - Static capability is enabled for this LAG interface
disable(2) - Static capability is disabled for this LAG interfacerw HmEnabledStatus (HM2-TC-MIB) .1.3.6.1.4.1.248.12.1.2.2.2.1.11 |
hm2AgentLagSummaryHashOptionLAG Hashing Option.
Valid values correspond to
1 (=Source MAC, VLAN, EtherType, and incoming port
associated with the packet)
2 (=Destination MAC, VLAN, EtherType, and incoming port
associated with the packet)
3 (=Source/Destination MAC, VLAN, EtherType, and incoming
port associated with the packet)
4 (=Source IP and Source TCP/UDP fields of the packet)
5 (=Destination IP and Destination TCP/UDP Port fields
of the packet)
6 (=Source/Destination IP and source/destination TCP/UDP
Port fields of the packet)
7 (=Enhanced hashing mode)
Support for particular options may vary by device.rw Enumeration .1.3.6.1.4.1.248.12.1.2.2.2.1.12 |
hm2AgentLagSummaryMinimumActiveLinksAgent LAG Threshold.
This configures the threshold(i.e minimum number of active ports)
value for trunk port .rw Integer32 .1.3.6.1.4.1.248.12.1.2.2.2.1.13 |
hm2AgentLagSummaryMaxFrameSizeLimitThis object identifies the largest value that can be
configured for hm2AgentLagSummaryMaxFrameSize.ro Integer32 .1.3.6.1.4.1.248.12.1.2.2.2.1.248 |
hm2AgentLagSummaryMaxFrameSizeThis object identifies the currently configured maximum frame size
value for this port. The maximum value that this object can be set
to is the value of hm2AgentLagSummaryMaxFrameSizeLimit. For Ethernet ports
which support 802.1Q vlan tagging, the minimum value that this object
can be set to is 1522rw Integer32 .1.3.6.1.4.1.248.12.1.2.2.2.1.249 |
hm2AgentLagDetailedConfigTableA detailed table of the switch's LAG config entries SEQUENCE OF Hm2AgentLagDetailedConfigEntry .1.3.6.1.4.1.248.12.1.2.2.3 |
hm2AgentLagDetailedConfigEntrySwitch's LAG config entry Hm2AgentLagDetailedConfigEntry .1.3.6.1.4.1.248.12.1.2.2.3.1 |
hm2AgentLagDetailedLagIndexLAG indexro Integer32 .1.3.6.1.4.1.248.12.1.2.2.3.1.1 |
hm2AgentLagDetailedIfIndexLAG port indexro Integer32 .1.3.6.1.4.1.248.12.1.2.2.3.1.2 |
hm2AgentLagDetailedPortSpeedLAG port speed. See agentPortType for a description and list
of valid values.ro OBJECT IDENTIFIER .1.3.6.1.4.1.248.12.1.2.2.3.1.3 |
hm2AgentLagDetailedPortStatusLAG port status.
active(1) - Actively participating in the LAG.
inactive(2) - Not participating in the LAG.ro Enumeration .1.3.6.1.4.1.248.12.1.2.2.3.1.4 |
hm2AgentLagConfigStaticCapabilityAgent LAG Static Capability.
Configures whether Static LAGs are supported on this device.rwobsolete HmEnabledStatus (HM2-TC-MIB) .1.3.6.1.4.1.248.12.1.2.2.4 |
hm2AgentLagConfigGroupHashOptionLAG Hashing Option.
Valid values correspond to
1 (=Source MAC, VLAN, EtherType, and incoming port
associated with the packet)
2 (=Destination MAC, VLAN, EtherType, and incoming port
associated with the packet)
3 (=Source/Destination MAC, VLAN, EtherType, and incoming
port associated with the packet)
4 (=Source IP and Source TCP/UDP fields of the packet)
5 (=Destination IP and Destination TCP/UDP Port fields
of the packet)
6 (=Source/Destination IP and source/destination TCP/UDP
Port fields of the packet)
7 (=Enhanced hashing mode)
Support for particular options may vary by device.rw Enumeration .1.3.6.1.4.1.248.12.1.2.2.5 |
hm2AgentLagConfigGroupMaxNumPortsPerLagThe maximum number of ports per LAG supported on this device.ro Unsigned32 .1.3.6.1.4.1.248.12.1.2.2.248 |
hm2AgentLagConfigGroupMaxNumOfLagsThe maximum number of LAGs this device supports.ro Unsigned32 .1.3.6.1.4.1.248.12.1.2.2.249 |
hm2AgentLagConfigGroupNumOfLagsConfiguredThe number of LAGs currently configured on this device.ro Unsigned32 .1.3.6.1.4.1.248.12.1.2.2.250 |
hm2AgentLagConfigGroupLagsConfiguredThe LAGs currently configured on the device.ro LagList .1.3.6.1.4.1.248.12.1.2.2.251 |
hm2AgentLagConfigSNMPExtensionGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.12.1.2.2.260 |
hm2AgentLagConfigGroupPortIsLagMemberErrorReturnIndicates that the port is unavailable for current setting because it is a LAG member. OBJECT IDENTIFIER .1.3.6.1.4.1.248.12.1.2.2.260.1 |
hm2AgentLagMirrorProbePortLagMemberErrorReturnThe port cannot be added because it is already a probe port. OBJECT IDENTIFIER .1.3.6.1.4.1.248.12.1.2.2.260.2 |
hm2AgentSwitchConfigGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.12.1.2.8 |
hm2AgentSwitchAddressAgingTimeoutTableThe switch's address aging timeout table SEQUENCE OF Hm2AgentSwitchAddressAgingTimeoutEntry .1.3.6.1.4.1.248.12.1.2.8.4 |
hm2AgentSwitchAddressAgingTimeoutEntryAging information about a specific Filtering Database. Hm2AgentSwitchAddressAgingTimeoutEntry .1.3.6.1.4.1.248.12.1.2.8.4.1 |
hm2AgentSwitchAddressAgingTimeoutThe FDB entry's address aging timeout (in seconds)rw Integer32 .1.3.6.1.4.1.248.12.1.2.8.4.1.1 |
hm2AgentSwitchStaticMacFilteringTableThe switch's static Mac filtering table SEQUENCE OF Hm2AgentSwitchStaticMacFilteringEntry .1.3.6.1.4.1.248.12.1.2.8.5 |
hm2AgentSwitchStaticMacFilteringEntryPer port ingress/egress filter configuration based on VLAN Id and MAC address. Hm2AgentSwitchStaticMacFilteringEntry .1.3.6.1.4.1.248.12.1.2.8.5.1 |
hm2AgentSwitchStaticMacFilteringVlanIdThe Static MAC Filter Vlan Idro Integer32 .1.3.6.1.4.1.248.12.1.2.8.5.1.1 |
hm2AgentSwitchStaticMacFilteringAddressThe Static MAC Filter MAC addressro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.248.12.1.2.8.5.1.2 |
hm2AgentSwitchStaticMacFilteringSourcePortMaskThe Static MAC Filter source port mask.
When setting this value, the system will ignore configuration for ports not
between the first and last valid ports. Configuration of any port numbers
between this range that are not valid ports return a failure message, but will
still apply configuration for valid ports.
To obtain port numbers from interface numbers, use the objects
hm2AgentPortDot1dBasePort and hm2AgentPortIfIndex in the hm2AgentPortConfigTable
table.rw Hm2AgentPortMask .1.3.6.1.4.1.248.12.1.2.8.5.1.3 |
hm2AgentSwitchStaticMacFilteringDestPortMaskThe Static MAC Filter destination port mask.
When setting this value, the system will ignore configuration for ports not
between the first and last valid ports. Configuration of any port numbers
between this range that are not valid ports return a failure message, but will
still apply configuration for valid ports.
To obtain port numbers from interface numbers, use the objects
hm2AgentPortDot1dBasePort and hm2AgentPortIfIndex in the hm2AgentPortConfigTable
table.
Configuring destination port mask for a unicast MAC filter is not supported on some platforms.rw Hm2AgentPortMask .1.3.6.1.4.1.248.12.1.2.8.5.1.4 |
hm2AgentSwitchStaticMacFilteringStatusThe Static MAC Filter status.
Supported values:
active(1) - valid entry
createAndGo(4) - used to create a new entry
destroy(6) - removes the entryrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.248.12.1.2.8.5.1.5 |
hm2AgentSwitchSnoopingGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.12.1.2.8.6 |
hm2AgentSwitchSnoopingCfgTableA table of the IGMP/MLD Snooping Global configuration entries. SEQUENCE OF Hm2AgentSwitchSnoopingCfgEntry .1.3.6.1.4.1.248.12.1.2.8.6.1 |
hm2AgentSwitchSnoopingCfgEntryRepresents entry for Snooping switch Configuration. Hm2AgentSwitchSnoopingCfgEntry .1.3.6.1.4.1.248.12.1.2.8.6.1.1 |
hm2AgentSwitchSnoopingProtocolThe protocol type of network protocol in use.ro InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.248.12.1.2.8.6.1.1.1 |
hm2AgentSwitchSnoopingAdminModeThis enables or disables Snooping on the system.rw HmEnabledStatus (HM2-TC-MIB) .1.3.6.1.4.1.248.12.1.2.8.6.1.1.2 |
hm2AgentSwitchSnoopingPortMaskIGMP/MLD Snooping Port Mask.
This allows configuration of IGMP/MLD Snooping on selected ports.
IGMP/MLD Snooping cannot be enabled on an interface that has routing
enabled, or is a member of a LAG. If a port which has IGMP/MLD Snooping
enabled becomes enabled for routing, or is enlisted as a member of a
LAG, IGMP/MLD Snooping functionality will be disabled on that port. IGMP/MLD
Snooping functionality will be subsequently be reenabled if routing is
disabled or LAG membership is removed from an interface that had previously
had IGMP/MLD Snooping enabled.
To obtain port numbers from interface numbers, use the objects
hm2AgentPortDot1dBasePort and hm2AgentPortIfIndex in the hm2AgentPortConfigTable
table.rw Hm2AgentPortMask .1.3.6.1.4.1.248.12.1.2.8.6.1.1.3 |
hm2AgentSwitchSnoopingMulticastControlFramesProcessedMulticast Control Frames Processed by CPU.
The number of multicast control frames that have been processed by the CPU.ro Counter32 .1.3.6.1.4.1.248.12.1.2.8.6.1.1.4 |
hm2AgentSwitchSnoopingIntfGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.12.1.2.8.7 |
hm2AgentSwitchSnoopingIntfTableA table of the IGMP/MLD Snooping Interface configuration entries. SEQUENCE OF Hm2AgentSwitchSnoopingIntfEntry .1.3.6.1.4.1.248.12.1.2.8.7.1 |
hm2AgentSwitchSnoopingIntfEntryRepresents entry for a IGMP/MLD Snooping Interface. Hm2AgentSwitchSnoopingIntfEntry .1.3.6.1.4.1.248.12.1.2.8.7.1.1 |
hm2AgentSwitchSnoopingIntfIndexThe port number to be selected. Each port maps to an interface.ro Unsigned32 .1.3.6.1.4.1.248.12.1.2.8.7.1.1.1 |
hm2AgentSwitchSnoopingIntfAdminModeThis enables or disables IGMP/MLD Snooping on a selected interface.rw HmEnabledStatus (HM2-TC-MIB) .1.3.6.1.4.1.248.12.1.2.8.7.1.1.2 |
hm2AgentSwitchSnoopingIntfGroupMembershipIntervalThe amount of time in seconds that a switch will wait for a report
from a particular group on the selected interface before deleting the
interface from the entry. This value must be greater than
hm2AgentSwitchSnoopingIntfMaxResponseTime.rw Integer32 .1.3.6.1.4.1.248.12.1.2.8.7.1.1.3 |
hm2AgentSwitchSnoopingIntfMaxResponseTimeThe amount of time in seconds a switch will wait after sending
a query on the selected interface because it did not receive a report for
a particular group in that interface. This value must be less
than hm2AgentSwitchSnoopingIntfGroupMembershipInterval. For IGMP Snooping,
this value ranges from 1 to 25 and for MLD Snooping, this value
ranges from 1 to 65.rw Integer32 .1.3.6.1.4.1.248.12.1.2.8.7.1.1.4 |
hm2AgentSwitchSnoopingIntfMRPExpirationTimeThe amount of time in seconds that a switch will wait for a query to be
received on the selected interface before the interface is removed from
the list of interfaces with multicast routers attached.
A value of 0 represents an 'infinite' interval.rw Integer32 .1.3.6.1.4.1.248.12.1.2.8.7.1.1.5 |
hm2AgentSwitchSnoopingIntfFastLeaveAdminModeThis enables or disables IGMP/MLD Snooping on the selected interface.rw HmEnabledStatus (HM2-TC-MIB) .1.3.6.1.4.1.248.12.1.2.8.7.1.1.6 |
hm2AgentSwitchSnoopingIntfMulticastRouterModeThe port explicitly configured by management to be IGMP query port for all VLANs.rw HmEnabledStatus (HM2-TC-MIB) .1.3.6.1.4.1.248.12.1.2.8.7.1.1.7 |
hm2AgentSwitchSnoopingIntfVlanIDsThis field lists all the VlanIDs which include the selected interface.ro VlanList .1.3.6.1.4.1.248.12.1.2.8.7.1.1.8 |
hm2AgentSwitchSnoopingVlanGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.12.1.2.8.8 |
hm2AgentSwitchSnoopingVlanTableA table of the IGMP/MLD Snooping Vlan configuration entries. SEQUENCE OF Hm2AgentSwitchSnoopingVlanEntry .1.3.6.1.4.1.248.12.1.2.8.8.1 |
hm2AgentSwitchSnoopingVlanEntryRepresents entry for a IGMP/MLD Snooping Vlan. Hm2AgentSwitchSnoopingVlanEntry .1.3.6.1.4.1.248.12.1.2.8.8.1.1 |
hm2AgentSwitchSnoopingVlanAdminModeThis enables or disables IGMP/MLD Snooping on a selected Vlan interface.rw HmEnabledStatus (HM2-TC-MIB) .1.3.6.1.4.1.248.12.1.2.8.8.1.1.1 |
hm2AgentSwitchSnoopingVlanGroupMembershipIntervalThe amount of time in seconds that a switch will wait for a report
from a particular group on the selected vlan before deleting the
interface participating in the vlan from the entry. This value must
be greater than hm2AgentSwitchSnoopingIntfMaxResponseTime.rw Integer32 .1.3.6.1.4.1.248.12.1.2.8.8.1.1.2 |
hm2AgentSwitchSnoopingVlanMaxResponseTimeThe amount of time in seconds a switch will wait after sending
a query on the selected vlan because it did not receive a report for
a particular group in the interface participating in the vlan.
This value must be less than
hm2AgentSwitchSnoopingIntfGroupMembershipInterval. For IGMP Snooping,
this value ranges from 1 to 25 and for MLD Snooping, this value
ranges from 1 to 65.rw Integer32 .1.3.6.1.4.1.248.12.1.2.8.8.1.1.3 |
hm2AgentSwitchSnoopingVlanFastLeaveAdminModeThis enables or disables IGMP/MLD Snooping on the selected vlan.rw HmEnabledStatus (HM2-TC-MIB) .1.3.6.1.4.1.248.12.1.2.8.8.1.1.4 |
hm2AgentSwitchSnoopingVlanMRPExpirationTimeThe amount of time in seconds that a switch will wait for a query to be
received on the selected interface participating in the vlan before the
interface is removed from the list of interfaces with multicast routers
attached. This parameter is configurable only for existing VLANs.
A value of 0 represents an 'infinite' interval.rw Integer32 .1.3.6.1.4.1.248.12.1.2.8.8.1.1.5 |
hm2AgentSwitchSnoopingVlanReportSuppModeThis enables or disables IGMP/MLD Snooping Report Suppression feature on the selected vlan.rw HmEnabledStatus (HM2-TC-MIB) .1.3.6.1.4.1.248.12.1.2.8.8.1.1.6 |
hm2AgentSwitchVlanStaticMrouterGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.12.1.2.8.9 |
hm2AgentSwitchVlanStaticMrouterTableA table of the IGMP/MLD Static Mrouter Configuration parameters. SEQUENCE OF Hm2AgentSwitchVlanStaticMrouterEntry .1.3.6.1.4.1.248.12.1.2.8.9.1 |
hm2AgentSwitchVlanStaticMrouterEntryRepresents entry for a IGMP/MLD Static Mrouter. Hm2AgentSwitchVlanStaticMrouterEntry .1.3.6.1.4.1.248.12.1.2.8.9.1.1 |
hm2AgentSwitchVlanStaticMrouterAdminModeThis enables or disables IGMP/MLD mrouter on a per interface per VLAN basis.rw HmEnabledStatus (HM2-TC-MIB) .1.3.6.1.4.1.248.12.1.2.8.9.1.1.1 |
hm2AgentSwitchMFDBGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.12.1.2.8.10 |
hm2AgentSwitchMFDBTableThe Multicast Forwarding Database table SEQUENCE OF Hm2AgentSwitchMFDBEntry .1.3.6.1.4.1.248.12.1.2.8.10.1 |
hm2AgentSwitchMFDBEntryContains Forwarding and Filtering information per Vlan Index, MAC Address, and
Component User. Hm2AgentSwitchMFDBEntry .1.3.6.1.4.1.248.12.1.2.8.10.1.1 |
hm2AgentSwitchMFDBVlanIdVlan Index for which this entry is associated with.ro VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.248.12.1.2.8.10.1.1.1 |
hm2AgentSwitchMFDBMacAddressA multicast MAC address for which the switch has forwarding and or
filtering information.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.248.12.1.2.8.10.1.1.2 |
hm2AgentSwitchMFDBProtocolTypeThe component that is responsible for this entry in the Multicast
Forwarding Database.ro Enumeration .1.3.6.1.4.1.248.12.1.2.8.10.1.1.3 |
hm2AgentSwitchMFDBTypeThis displays the type of the entry.
static(1) - Entries configured by the end user
dynamic(2) - Entries added as a result of a learning process or protocolro Enumeration .1.3.6.1.4.1.248.12.1.2.8.10.1.1.4 |
hm2AgentSwitchMFDBDescriptionText description of this multicast table entry.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.248.12.1.2.8.10.1.1.5 |
hm2AgentSwitchMFDBForwardingPortMaskBitMask indicating which ports this entry indicates should be forwarded.
To obtain port numbers from interface numbers, use the objects
hm2AgentPortDot1dBasePort and hm2AgentPortIfIndex in the hm2AgentPortConfigTable
table.ro Hm2AgentPortMask .1.3.6.1.4.1.248.12.1.2.8.10.1.1.6 |
hm2AgentSwitchMFDBFilteringPortMaskBitMask indicating which ports this entry indicates should be filtered.
To obtain port numbers from interface numbers, use the objects
hm2AgentPortDot1dBasePort and hm2AgentPortIfIndex in the hm2AgentPortConfigTable
table.ro Hm2AgentPortMask .1.3.6.1.4.1.248.12.1.2.8.10.1.1.7 |
hm2AgentSwitchMFDBSummaryTableThe multicast forwarding database summary table. SEQUENCE OF Hm2AgentSwitchMFDBSummaryEntry .1.3.6.1.4.1.248.12.1.2.8.10.2 |
hm2AgentSwitchMFDBSummaryEntrySummarizes the forwarding ports for all components registered for all
MFDB table entries with the same Vlan Index and MAC Address. Hm2AgentSwitchMFDBSummaryEntry .1.3.6.1.4.1.248.12.1.2.8.10.2.1 |
hm2AgentSwitchMFDBSummaryVlanIdVlan Index for which this entry is associated with.ro VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.248.12.1.2.8.10.2.1.1 |
hm2AgentSwitchMFDBSummaryMacAddressA multicast MAC address for which the switch has forwarding and or
filtering information.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.248.12.1.2.8.10.2.1.2 |
hm2AgentSwitchMFDBSummaryForwardingPortMaskPort Mask indicating which ports this entry indicates should be forwarded.
To obtain port numbers from interface numbers, use the objects
hm2AgentPortDot1dBasePort and hm2AgentPortIfIndex in the hm2AgentPortConfigTable
table.ro Hm2AgentPortMask .1.3.6.1.4.1.248.12.1.2.8.10.2.1.3 |
hm2AgentSwitchMFDBMaxTableEntriesThis displays the maximum number of entries that can possibly be in
the Multicast Forwarding Database table.ro Gauge32 .1.3.6.1.4.1.248.12.1.2.8.10.3 |
hm2AgentSwitchMFDBMostEntriesUsedThis displays the largest number of entries that have been present
in the Multicast Forwarding Database table. This value is also known
as the MFDB high water mark.ro Gauge32 .1.3.6.1.4.1.248.12.1.2.8.10.4 |
hm2AgentSwitchMFDBCurrentEntriesThis displays the current number of entries in the Multicast
Forwarding Database table.ro Gauge32 .1.3.6.1.4.1.248.12.1.2.8.10.5 |
hm2AgentSwitchVlanMacAssociationGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.12.1.2.8.17 |
hm2AgentSwitchVlanMacAssociationTableThe switch's MAC To VLAN association table SEQUENCE OF Hm2AgentSwitchVlanMacAssociationEntry .1.3.6.1.4.1.248.12.1.2.8.17.1 |
hm2AgentSwitchVlanMacAssociationEntryVLAN to be assigned to untagged or priority tagged
packets based on MAC address. Hm2AgentSwitchVlanMacAssociationEntry .1.3.6.1.4.1.248.12.1.2.8.17.1.1 |
hm2AgentSwitchVlanMacAssociationMacAddressThe Mac address MacAddress (SNMPv2-TC) .1.3.6.1.4.1.248.12.1.2.8.17.1.1.1 |
hm2AgentSwitchVlanMacAssociationVlanIdThe VLAN the Mac address assigned to VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.248.12.1.2.8.17.1.1.2 |
hm2AgentSwitchVlanMacAssociationRowStatusThe Mac to VLAN association row status.
Supported values:
active(1) - valid entry
createAndGo(4) - used to create a new entry
destroy(6) - removes the entryrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.248.12.1.2.8.17.1.1.3 |
hm2AgentSwitchProtectedPortConfigGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.12.1.2.8.18 |
hm2AgentSwitchProtectedPortTableThe switch's protected port mapping table SEQUENCE OF Hm2AgentSwitchProtectedPortEntry .1.3.6.1.4.1.248.12.1.2.8.18.1 |
hm2AgentSwitchProtectedPortEntryProtected ports assigned to groups. Hm2AgentSwitchProtectedPortEntry .1.3.6.1.4.1.248.12.1.2.8.18.1.1 |
hm2AgentSwitchProtectedPortGroupIdThe group that this port belongs to Integer32 .1.3.6.1.4.1.248.12.1.2.8.18.1.1.1 |
hm2AgentSwitchProtectedPortGroupNameThe name of the grouprw DisplayString .1.3.6.1.4.1.248.12.1.2.8.18.1.1.2 |
hm2AgentSwitchProtectedPortPortListThe set of ports that are protected in this grouprw PortList (Q-BRIDGE-MIB) .1.3.6.1.4.1.248.12.1.2.8.18.1.1.3 |
hm2AgentSwitchVlanSubnetAssociationGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.12.1.2.8.19 |
hm2AgentSwitchVlanSubnetAssociationTableThe switch's Subnet To VLAN association table SEQUENCE OF Hm2AgentSwitchVlanSubnetAssociationEntry .1.3.6.1.4.1.248.12.1.2.8.19.1 |
hm2AgentSwitchVlanSubnetAssociationEntryVLAN to be assigned to untagged or priority tagged
packets based on IP address and Subnet Mask. Hm2AgentSwitchVlanSubnetAssociationEntry .1.3.6.1.4.1.248.12.1.2.8.19.1.1 |
hm2AgentSwitchVlanSubnetAssociationIPAddressThe ip address IpAddress .1.3.6.1.4.1.248.12.1.2.8.19.1.1.1 |
hm2AgentSwitchVlanSubnetAssociationSubnetMaskThe subnet mask IpAddress .1.3.6.1.4.1.248.12.1.2.8.19.1.1.2 |
hm2AgentSwitchVlanSubnetAssociationVlanIdThe VLAN that the IP address and subnet mask assigned to VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.248.12.1.2.8.19.1.1.3 |
hm2AgentSwitchVlanSubnetAssociationRowStatusThe Subnet to VLAN association row status.
Supported values:
active(1) - valid entry
createAndGo(4) - used to create a new entry
destroy(6) - removes the entryrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.248.12.1.2.8.19.1.1.4 |
hm2AgentSwitchSnoopingQuerierGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.12.1.2.8.20 |
hm2AgentSwitchSnoopingQuerierCfgTableA table of the IGMP/MLD Snooping Querier Global configuration entries. SEQUENCE OF Hm2AgentSwitchSnoopingQuerierCfgEntry .1.3.6.1.4.1.248.12.1.2.8.20.1 |
hm2AgentSwitchSnoopingQuerierCfgEntryRepresents entry for Snooping Querier Configuration. Hm2AgentSwitchSnoopingQuerierCfgEntry .1.3.6.1.4.1.248.12.1.2.8.20.1.1 |
hm2AgentSwitchSnoopingQuerierAdminModeThis enables or disables Snooping Querier on the system.rw HmEnabledStatus (HM2-TC-MIB) .1.3.6.1.4.1.248.12.1.2.8.20.1.1.1 |
hm2AgentSwitchSnoopingQuerierVersionThis specifies the multicast protocol versions that are
supported by the system.rw Integer32 .1.3.6.1.4.1.248.12.1.2.8.20.1.1.2 |
hm2AgentSwitchSnoopingQuerierQueryIntervalThis specified the timer interval after which the system
generates general queries.rw Integer32 .1.3.6.1.4.1.248.12.1.2.8.20.1.1.4 |
hm2AgentSwitchSnoopingQuerierExpiryIntervalThis specified the timer interval after which the detected
other querier information is no longer valid.rw Integer32 .1.3.6.1.4.1.248.12.1.2.8.20.1.1.5 |
hm2AgentSwitchSnoopingQuerierVlanTableA table of the Snooping Querier Vlan configuration entries. SEQUENCE OF Hm2AgentSwitchSnoopingQuerierVlanEntry .1.3.6.1.4.1.248.12.1.2.8.20.2 |
hm2AgentSwitchSnoopingQuerierVlanEntryRepresents entry for a Snooping Querier configurable Vlan. Hm2AgentSwitchSnoopingQuerierVlanEntry .1.3.6.1.4.1.248.12.1.2.8.20.2.1 |
hm2AgentSwitchSnoopingQuerierVlanAdminModeThis enables or disables Snooping Querier on a selected Vlan interface.rw HmEnabledStatus (HM2-TC-MIB) .1.3.6.1.4.1.248.12.1.2.8.20.2.1.1 |
hm2AgentSwitchSnoopingQuerierVlanOperModeThis specifies the current state of the Snooping Querier on a selected vlan interfacero Enumeration .1.3.6.1.4.1.248.12.1.2.8.20.2.1.2 |
hm2AgentSwitchSnoopingQuerierElectionParticipateModeThis object is deprecated.
This enables or disables the Snooping Querier Election Participation mode. When enabled
snooping querier switch will participate in querier election up on discovering another
querier in the specified vlan. When disabled, up on discovering another querier, snooping
querier moves to non-querier state.
The state of the querier is solely set by hm2AgentSwitchSnoopingQuerierVlanAdminMode.
If hm2AgentSwitchSnoopingQuerierVlanAdminMode is set to
enable(1) hm2AgentSwitchSnoopingQuerierElectionParticipateMode will be set internally to enable(1).
If hm2AgentSwitchSnoopingQuerierVlanAdminMode is set to
disable(2) hm2AgentSwitchSnoopingQuerierElectionParticipateMode will be set internally to disable(2).rwdeprecated HmEnabledStatus (HM2-TC-MIB) .1.3.6.1.4.1.248.12.1.2.8.20.2.1.3 |
hm2AgentSwitchSnoopingQuerierVlanAddressThis specifies the default source ip address to be used while generating general queries on
the specified vlan.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.248.12.1.2.8.20.2.1.4 |
hm2AgentSwitchSnoopingQuerierOperVersionThis specifies the multicast protocol version that is currently being used by the snooping
switch for the specified vlan while generating query messages.ro Integer32 .1.3.6.1.4.1.248.12.1.2.8.20.2.1.5 |
hm2AgentSwitchSnoopingQuerierOperMaxResponseTimeThe amount of time in seconds a switch will wait after sending
a query on the selected vlan because it did not receive a report for
a particular group in the interface participating in the vlan. This
object is valid only when hm2AgentSwitchSnoopingQuerierOperVersion object
is valid.
(-1) - indicates that parameter is not available;
( 0) - indicates that response time is less then 1 second.ro Integer32(-1|0..2147483647) .1.3.6.1.4.1.248.12.1.2.8.20.2.1.6 |
hm2AgentSwitchSnoopingQuerierLastQuerierAddressThis specifies the last querier's ip address for the specified vlan.
It represents the detected other multicast querier in the vlan.ro InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.248.12.1.2.8.20.2.1.7 |
hm2AgentSwitchSnoopingQuerierLastQuerierVersionThis specifies the multicast protocol version that is currently being used
by the detected other multicast querier for the specified vlan.
(-1) - indicates that parameter is not available.ro Integer32 .1.3.6.1.4.1.248.12.1.2.8.20.2.1.8 |
hm2AgentDaiConfigGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.12.1.2.8.21 |
hm2AgentDaiSrcMacValidateThis object indicates whether Sender MAC validation in the ARP
packets is enabled.
If this object is set to 'true', validation
is enabled.
If this object is set to 'false', validation
is disabled.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.248.12.1.2.8.21.1 |
hm2AgentDaiDstMacValidateThis object indicates whether Target MAC validation in the ARP
Response packets is enabled.
If this object is set to 'true', validation
is enabled.
If this object is set to 'false', validation
is disabled.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.248.12.1.2.8.21.2 |
hm2AgentDaiIPValidateThis object indicates whether IP address validation in the ARP
packets is enabled.
If this object is set to 'true', validation
is enabled.
If this object is set to 'false', validation
is disabled.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.248.12.1.2.8.21.3 |
hm2AgentDaiVlanConfigTableA table provides the mechanism to control Dynamic ARP
Inspection per VLAN. When a VLAN is created in a device
supporting this table, a corresponding entry of this table
will be added. SEQUENCE OF Hm2AgentDaiVlanConfigEntry .1.3.6.1.4.1.248.12.1.2.8.21.4 |
hm2AgentDaiVlanConfigEntryA row instance contains the configuration for Dynamic
ARP Inspection at each existing VLAN. Hm2AgentDaiVlanConfigEntry .1.3.6.1.4.1.248.12.1.2.8.21.4.1 |
hm2AgentDaiVlanIndexThis object indicates the VLAN number on which Dynamic ARP
Inspection feature is configured. VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.248.12.1.2.8.21.4.1.1 |
hm2AgentDaiVlanDynArpInspEnableThis object indicates whether Dynamic ARP Inspection is
enabled in this VLAN.
If this object is set to 'true', Dynamic ARP Inspection
is enabled.
If this object is set to 'false', Dynamic ARP Inspection
is disabled.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.248.12.1.2.8.21.4.1.2 |
hm2AgentDaiVlanLoggingEnableThis object indicates whether the Dynamic ARP Inspection
logging is enabled on this VlAN.
If this object is set to 'true', Dynamic ARP Inspection
logging is enabled.
If this object is set to 'false', Dynamic ARP Inspection
loging is disabled.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.248.12.1.2.8.21.4.1.3 |
hm2AgentDaiVlanArpAclNameThis object indicates the ARP ACL name set for this VLAN. Notice
that the ACL is regarded only if the corresponding row in
'agentArpAclTable' is active.rw DisplayString .1.3.6.1.4.1.248.12.1.2.8.21.4.1.4 |
hm2AgentDaiVlanArpAclStaticFlagIf an ARP ACL is defined for the VLAN and there is no match for
the received ARP packet, the further proceeding depends on this
MIB object. If it is 'true', then the packet is dropped, otherwise
the packet is checked against the DHCP snooping bindings database
(optional, see 'hm2AgentDaiVlanBindingCheckEnable'). If there is
no match in the bindings database too, the packet is dropped.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.248.12.1.2.8.21.4.1.5 |
hm2AgentDaiVlanBindingCheckEnableIf enabled, the ARP frame received on an untrusted port (in a DAI
enabled VLAN) is checked against the ARP ACL and the DHCP Snooping
bindings database. If disabled it is only checked against the ARP
ACL.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.248.12.1.2.8.21.4.1.248 |
hm2AgentDaiStatsResetClear the DAI statistics on all vlans. A value of reset(1)
is used to reset the statistics. A read on this object will
always return the value none(0). The value none(0) cannot
be forcibly set by the administrator.rw Enumeration .1.3.6.1.4.1.248.12.1.2.8.21.5 |
hm2AgentDaiVlanStatsTableA table provides the mechanism to control Dynamic ARP
Inspection per VLAN. When a VLAN is created in a device
supporting this table, a corresponding entry of this table
will be added. SEQUENCE OF Hm2AgentDaiVlanStatsEntry .1.3.6.1.4.1.248.12.1.2.8.21.6 |
hm2AgentDaiVlanStatsEntryA row instance contains the Dynamic ARP Inspection
statistics per VLAN. Hm2AgentDaiVlanStatsEntry .1.3.6.1.4.1.248.12.1.2.8.21.6.1 |
hm2AgentDaiVlanStatsIndexThis object indicates the VLAN number on which Dynamic ARP
Inspection statistics are retrieved. VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.248.12.1.2.8.21.6.1.1 |
hm2AgentDaiVlanPktsForwardedNumber of valid ARP packets forwarded by DAI.ro Counter32 .1.3.6.1.4.1.248.12.1.2.8.21.6.1.2 |
hm2AgentDaiVlanPktsDroppedNumber of invalid ARP packets dropped by DAI.ro Counter32 .1.3.6.1.4.1.248.12.1.2.8.21.6.1.3 |
hm2AgentDaiVlanDhcpDropsNumber of ARP packets that were dropped by DAI as
there is no matching DHCP Snooping binding entry found.ro Counter32 .1.3.6.1.4.1.248.12.1.2.8.21.6.1.4 |
hm2AgentDaiVlanDhcpPermitsNumber of ARP packets that were forwarded by DAI as
there is a matching DHCP Snooping binding entry found.ro Counter32 .1.3.6.1.4.1.248.12.1.2.8.21.6.1.5 |
hm2AgentDaiVlanAclDropsNumber of ARP packets that were dropped by DAI as
there is no matching ARP ACL rule found for this Vlan and
the static flag is set on this vlan.ro Counter32 .1.3.6.1.4.1.248.12.1.2.8.21.6.1.6 |
hm2AgentDaiVlanAclPermitsNumber of ARP packets that were permitted by DAI as
there is a matching ARP ACL rule found for this Vlan.ro Counter32 .1.3.6.1.4.1.248.12.1.2.8.21.6.1.7 |
hm2AgentDaiVlanSrcMacFailuresNumber of ARP packets that were dropped by DAI as the
sender mac address in ARP packet didn't match the source
mac in ethernet header.ro Counter32 .1.3.6.1.4.1.248.12.1.2.8.21.6.1.8 |
hm2AgentDaiVlanDstMacFailuresNumber of ARP packets that were dropped by DAI as the
target mac address in ARP reply packet didn't match the
destination mac in ethernet header.ro Counter32 .1.3.6.1.4.1.248.12.1.2.8.21.6.1.9 |
hm2AgentDaiVlanIpValidFailuresNumber of ARP packets that were dropped by DAI as the
sender IP address in ARP packet or target IP address in
ARP reply packet is invalid. Invalid addresses include
0.0.0.0, 255.255.255.255, IP multicast addresses,
class E addresses (240.0.0.0/4), loopback addresses (127.0.0.0/8).ro Counter32 .1.3.6.1.4.1.248.12.1.2.8.21.6.1.10 |
hm2AgentDaiIfConfigTableA table provides the mechanism to configure the trust
state for Dynamic ARP Inspection purpose at each physical
interface capable of this feature. SEQUENCE OF Hm2AgentDaiIfConfigEntry .1.3.6.1.4.1.248.12.1.2.8.21.7 |
hm2AgentDaiIfConfigEntryA row instance contains the configuration for
Dynamic ARP Inspection at each physical
interface capable of this feature. Hm2AgentDaiIfConfigEntry .1.3.6.1.4.1.248.12.1.2.8.21.7.1 |
hm2AgentDaiIfTrustEnableThis object indicates whether the interface is trusted for
Dynamic ARP Inspection purpose.
If this object is set to 'true', the interface is trusted.
ARP packets coming to this interface will be forwarded
without checking.
If this object is set to 'false', the interface is not
trusted. ARP packets coming to this interface will be
subjected to ARP inspection.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.248.12.1.2.8.21.7.1.1 |
hm2AgentDaiIfRateLimitThis object indicates rate limit value for Dynamic ARP
Inspection purpose. If the incoming rate of ARP packets
exceeds the value of this object for consecutively
burst interval seconds, ARP packets will be
dropped. Value of -1 indicates that there is no rate limit.rw Integer32 (-1|0..300) UNITS "packets per second" .1.3.6.1.4.1.248.12.1.2.8.21.7.1.2 |
hm2AgentDaiIfBurstIntervalThis object indicates the burst interval value
for rate limiting purpose on this interface.rw Unsigned32 .1.3.6.1.4.1.248.12.1.2.8.21.7.1.3 |
hm2AgentDaiIfAutoDisableThis object indicates whether a port is auto-disabled when the
configured ARP threshold is exceeded.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.248.12.1.2.8.21.7.1.248 |
hm2AgentArpAclGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.12.1.2.8.22 |
hm2AgentArpAclTableA table of the ARP ACL entries SEQUENCE OF Hm2AgentArpAclEntry .1.3.6.1.4.1.248.12.1.2.8.22.1 |
hm2AgentArpAclEntryRepresents entry for an ARP ACL Hm2AgentArpAclEntry .1.3.6.1.4.1.248.12.1.2.8.22.1.1 |
hm2AgentArpAclNameName of the ARP ACL, which must consist of 1 to 31 alphanumeric
characters and uniquely identify this ARP ACL. This object must
be set to complete a new ARP ACL row instance.rw DisplayString .1.3.6.1.4.1.248.12.1.2.8.22.1.1.1 |
hm2AgentArpAclRowStatusThe status of this conceptual row. Entries can not be deleted until all rows in
arpAclRuleTable with corresponding values of arpAclIndex have been deleted.
active(1) - This ACL instance is active.
notInService(2) - Row has been suspended.
notReady(3) - Row has incomplete values.
createAndGo(4) - Accept row values and activate.
createAndWait(5) - Accept row values and wait.
destroy(6) - Set to this value to delete this instance.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.248.12.1.2.8.22.1.1.2 |
hm2AgentArpAclRuleTableA table of the ARP ACL Rule entries SEQUENCE OF Hm2AgentArpAclRuleEntry .1.3.6.1.4.1.248.12.1.2.8.22.2 |
hm2AgentArpAclRuleEntryRepresents entry for a set of ARP ACL-match rules Hm2AgentArpAclRuleEntry .1.3.6.1.4.1.248.12.1.2.8.22.2.1 |
hm2AgentArpAclRuleMatchSenderIpAddrSender IP address match value for the ARP ACL.
This address must be a unicast address unequal to 0.0.0.0.rw IpAddress .1.3.6.1.4.1.248.12.1.2.8.22.2.1.1 |
hm2AgentArpAclRuleMatchSenderMacAddrSender MAC address match value for the ARP ACL.
This address must be a unicast address unequal to 00:0:00:00:00:00.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.248.12.1.2.8.22.2.1.2 |
hm2AgentArpAclRuleRowStatusThe status of this conceptual row.
active(1) - This ACL Rule is active.
notInService(2) - Row has been suspended.
notReady(3) - Row has incomplete values.
createAndGo(4) - Accept row values and activate.
createAndWait(5) - Accept row values and wait.
destroy(6) - Set to this value to delete an instance.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.248.12.1.2.8.22.2.1.3 |
hm2AgentDhcpSnoopingConfigGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.12.1.2.8.23 |
hm2AgentDhcpSnoopingAdminModeThis object indicates whether DHCP Snooping
is enabled globally.
If this object is set to 'true',admin mode
is enabled globally.
If this object is set to 'false',admin mode
is disabled globally.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.248.12.1.2.8.23.1 |
hm2AgentDhcpSnoopingVerifyMacThis object indicates whether source Mac address
in the received DHCP Message needs to be verified or not.
If this object is set to 'true',verifyMac
is enabled globally.
If this object is set to 'false',verifyMac
is disabled globally.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.248.12.1.2.8.23.2 |
hm2AgentDhcpSnoopingVlanConfigTableA table provides the mechanism to control DHCP SNOOPING
per VLAN. When a VLAN is created in a device
supporting this table, a corresponding entry of this table
will be added. SEQUENCE OF Hm2AgentDhcpSnoopingVlanConfigEntry .1.3.6.1.4.1.248.12.1.2.8.23.3 |
hm2AgentDhcpSnoopingVlanConfigEntryA row instance contains the configuration for DHCP
SNOOPING at each existing VLAN. Hm2AgentDhcpSnoopingVlanConfigEntry .1.3.6.1.4.1.248.12.1.2.8.23.3.1 |
hm2AgentDhcpSnoopingVlanIndexThis object indicates the VLAN number on which DHCP SNOOPING
Inspection feature is configured. VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.248.12.1.2.8.23.3.1.1 |
hm2AgentDhcpSnoopingVlanEnableThis object indicates whether DHCP SNOOPING is
enabled in this VLAN.
If this object is set to 'true', DHCP SNOOPING
is enabled.
If this object is set to 'false', DHCP SNOOPING
is disabled.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.248.12.1.2.8.23.3.1.2 |
hm2AgentDhcpSnoopingIfConfigTableA table provides the mechanism to configure the trust
state for DHCP snooping purpose at each physical
interface capable of this feature. SEQUENCE OF Hm2AgentDhcpSnoopingIfConfigEntry .1.3.6.1.4.1.248.12.1.2.8.23.4 |
hm2AgentDhcpSnoopingIfConfigEntryA row instance contains the configuration for
DHCP snooping at each physical interface capable of this feature. Hm2AgentDhcpSnoopingIfConfigEntry .1.3.6.1.4.1.248.12.1.2.8.23.4.1 |
hm2AgentDhcpSnoopingIfTrustEnableThis object indicates whether the interface is trusted for
DHCP snooping purpose.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.248.12.1.2.8.23.4.1.1 |
hm2AgentDhcpSnoopingIfLogEnableThis object indicates whether the Logging needs on DHCP snooping validations
or notrw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.248.12.1.2.8.23.4.1.2 |
hm2AgentDhcpSnoopingIfRateLimitThis object indicates rate limit value for DHCP
Snooping purpose. If the incoming rate of DHCP packets
exceeds the value of this object for consecutively
burst interval seconds, DHCP packets will be
dropped. Value of -1 indicates that there is no rate limit.rw Integer32 (-1|0..150) UNITS "packets per second" .1.3.6.1.4.1.248.12.1.2.8.23.4.1.3 |
hm2AgentDhcpSnoopingIfBurstIntervalThis object indicates the burst interval value
for rate limiting purpose on this interface.rw Integer32 .1.3.6.1.4.1.248.12.1.2.8.23.4.1.4 |
hm2AgentDhcpSnoopingIfAutoDisableThis object indicates whether a port is auto-disabled when the
configured threshold is reached.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.248.12.1.2.8.23.4.1.248 |
hm2AgentIpsgIfConfigTableA table provides the mechanism to configure the IPSG
at each physical interface capable of this feature. SEQUENCE OF Hm2AgentIpsgIfConfigEntry .1.3.6.1.4.1.248.12.1.2.8.23.5 |
hm2AgentIpsgIfConfigEntryA row instance contains the configuration for
IPSG at each physical interface capable of this feature. Hm2AgentIpsgIfConfigEntry .1.3.6.1.4.1.248.12.1.2.8.23.5.1 |
hm2AgentIpsgIfVerifySourceThis object indicates whether IP packets received on this interface
are filtered based on whether IP Source Guard considers the source IP address
to be a valid client address. Setting this variable to false automatically
sets hm2AgentIpsgIfPortSecurity to false.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.248.12.1.2.8.23.5.1.1 |
hm2AgentIpsgIfPortSecurityThis object indicates whether IP packets received on this interface
are filtered based on whether IP Source Guard considers the source MAC address
to be a valid client address. The port security option cannot be enabled
unless hm2AgentIpsgIfVerifySource is also enabled. That is, MAC address filtering
cannot be done without also doing IP address filtering. But IP address filtering
can be done without MAC address filtering. Once the port security
option is enabled, it can only be disabled by disabling hm2AgentIpsgIfVerifySource.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.248.12.1.2.8.23.5.1.2 |
hm2AgentDhcpSnoopingStatsResetClear the DHCP snooping statistics on all ports. A value of reset(1)
is used to reset the statistics. A read on this object will
always return the value none(0). The value none(0) cannot
be forcibly set by the administrator.rw Enumeration .1.3.6.1.4.1.248.12.1.2.8.23.6 |
hm2AgentDhcpSnoopingStatsTableA table provides the mechanism for statics of DHCP snooping. SEQUENCE OF Hm2AgentDhcpSnoopingStatsEntry .1.3.6.1.4.1.248.12.1.2.8.23.7 |
hm2AgentDhcpSnoopingStatsEntryA row instance contains the DHCP snooping statistics per VLAN. Hm2AgentDhcpSnoopingStatsEntry .1.3.6.1.4.1.248.12.1.2.8.23.7.1 |
hm2AgentDhcpSnoopingMacVerifyFailuresThis object indicates the number of failure verifications of client mac address with
source mac addressro Counter32 .1.3.6.1.4.1.248.12.1.2.8.23.7.1.1 |
hm2AgentDhcpSnoopingInvalidClientMessagesThis object indicates the number of invalid DHCP releases and deny messagesro Counter32 .1.3.6.1.4.1.248.12.1.2.8.23.7.1.2 |
hm2AgentDhcpSnoopingInvalidServerMessagesThis object indicates the number of invalid DHCP server mesaagesro Counter32 .1.3.6.1.4.1.248.12.1.2.8.23.7.1.3 |
hm2AgentStaticIpsgBindingTableA table of the IPSG static entries SEQUENCE OF Hm2AgentStaticIpsgBindingEntry .1.3.6.1.4.1.248.12.1.2.8.23.8 |
hm2AgentStaticIpsgBindingEntryRepresents a binding in IPSG table Hm2AgentStaticIpsgBindingEntry .1.3.6.1.4.1.248.12.1.2.8.23.8.1 |
hm2AgentStaticIpsgBindingIfIndexInterface on which this IPSG binding is going to be added.rw InterfaceIndex (IF-MIB) .1.3.6.1.4.1.248.12.1.2.8.23.8.1.1 |
hm2AgentStaticIpsgBindingVlanIdVLAN to which this IPSG binding is going to be added.rw VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.248.12.1.2.8.23.8.1.2 |
hm2AgentStaticIpsgBindingMacAddrMAC address match value for the IPSG Binding.
This address must be a unicast address unequal to 00:0:00:00:00:00.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.248.12.1.2.8.23.8.1.3 |
hm2AgentStaticIpsgBindingIpAddrIP address match value for the IPSG Binding.
This address must be a unicast address unequal to 0.0.0.0.rw IpAddress .1.3.6.1.4.1.248.12.1.2.8.23.8.1.4 |
hm2AgentStaticIpsgBindingRowStatusThe status of this conceptual row.
active(1) - This DHCP Snooping binding is active.
notInService(2) - Row has been suspended.
notReady(3) - Row has incomplete values.
createAndGo(4) - Accept row values and activate.
createAndWait(5) - Accept row values and wait.
destroy(6) - Set to this value to remove this binding.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.248.12.1.2.8.23.8.1.5 |
hm2AgentStaticIpsgBindingHwStatusSet to true when Binding is applied to the Hardwarero TruthValue (SNMPv2-TC) .1.3.6.1.4.1.248.12.1.2.8.23.8.1.248 |
hm2AgentDynamicIpsgBindingTableA table of the IPSG dynamic entries SEQUENCE OF Hm2AgentDynamicIpsgBindingEntry .1.3.6.1.4.1.248.12.1.2.8.23.9 |
hm2AgentDynamicIpsgBindingEntryRepresents a binding in IPSG table Hm2AgentDynamicIpsgBindingEntry .1.3.6.1.4.1.248.12.1.2.8.23.9.1 |
hm2AgentDynamicIpsgBindingIfIndexInterface on which this IPSG binding is added.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.248.12.1.2.8.23.9.1.1 |
hm2AgentDynamicIpsgBindingVlanIdVLAN to which this IPSG binding is going to be added.ro VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.248.12.1.2.8.23.9.1.2 |
hm2AgentDynamicIpsgBindingMacAddrMAC address match value for the IPSG Binding.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.248.12.1.2.8.23.9.1.3 |
hm2AgentDynamicIpsgBindingIpAddrSender IP address match value for the IPSG Binding.ro IpAddress .1.3.6.1.4.1.248.12.1.2.8.23.9.1.4 |
hm2AgentDynamicIpsgBindingHwStatusSet to true when Binding is applied to the Hardwarero TruthValue (SNMPv2-TC) .1.3.6.1.4.1.248.12.1.2.8.23.9.1.248 |
hm2AgentStaticDsBindingTableA table of the DHCP SNOOPING static entries SEQUENCE OF Hm2AgentStaticDsBindingEntry .1.3.6.1.4.1.248.12.1.2.8.23.10 |
hm2AgentStaticDsBindingEntryRepresents a binding in DHCP SNOOPING table Hm2AgentStaticDsBindingEntry .1.3.6.1.4.1.248.12.1.2.8.23.10.1 |
hm2AgentStaticDsBindingIfIndexInterface on which this DHCP SNOOPING binding is going to be added.rw InterfaceIndexOrZero (IF-MIB) .1.3.6.1.4.1.248.12.1.2.8.23.10.1.1 |
hm2AgentStaticDsBindingVlanIdVLAN to which this DHCP SNOOPING binding is going to be added.rw VlanId (Q-BRIDGE-MIB) .1.3.6.1.4.1.248.12.1.2.8.23.10.1.2 |
hm2AgentStaticDsBindingMacAddrMAC address match value for the DHCP SNOOPING Binding.
This address must be a unicast address unequal to 00:0:00:00:00:00.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.248.12.1.2.8.23.10.1.3 |
hm2AgentStaticDsBindingIpAddrIP address match value for the DHCP SNOOPING Binding.
This address must be a unicast address unequal to 0.0.0.0.rw IpAddress .1.3.6.1.4.1.248.12.1.2.8.23.10.1.4 |
hm2AgentStaticDsBindingRowStatusThe status of this conceptual row.
active(1) - This DHCP Snooping binding is active.
notInService(2) - Row has been suspended.
notReady(3) - Row has incomplete values.
createAndGo(4) - Accept row values and activate.
createAndWait(5) - Accept row values and wait.
destroy(6) - Set to this value to remove this binding.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.248.12.1.2.8.23.10.1.5 |
hm2AgentDynamicDsBindingTableA table of the DHCP SNOOPING Dynamic entries SEQUENCE OF Hm2AgentDynamicDsBindingEntry .1.3.6.1.4.1.248.12.1.2.8.23.11 |
hm2AgentDynamicDsBindingEntryRepresents a binding in DHCP SNOOPING table Hm2AgentDynamicDsBindingEntry .1.3.6.1.4.1.248.12.1.2.8.23.11.1 |
hm2AgentDynamicDsBindingIfIndexInterface on which this DHCP SNOOPING binding is going to be added.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.248.12.1.2.8.23.11.1.1 |
hm2AgentDynamicDsBindingVlanIdVLAN to which this DHCP SNOOPING binding is going to be added.ro VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.248.12.1.2.8.23.11.1.2 |
hm2AgentDynamicDsBindingMacAddrMAC address match value for the DHCP SNOOPING Binding.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.248.12.1.2.8.23.11.1.3 |
hm2AgentDynamicDsBindingIpAddrIP address match value for the DHCP SNOOPING Binding.ro IpAddress .1.3.6.1.4.1.248.12.1.2.8.23.11.1.4 |
hm2AgentDynamicDsBindingLeaseRemainingTimeThis specifies the period for which the DHCP SNOOPING Binding is valid.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.248.12.1.2.8.23.11.1.5 |
hm2AgentDhcpSnoopingRemoteFileNameThis object indicates the file name on the remote machine
to save the DHCP Snooping bindings.rw DisplayString .1.3.6.1.4.1.248.12.1.2.8.23.12 |
hm2AgentDhcpSnoopingRemoteIpAddrThis object indicates the IP address of the remote machine
to save the DHCP Snooping bindings. This will be set only
when we have a valid file name.rw IpAddress .1.3.6.1.4.1.248.12.1.2.8.23.13 |
hm2AgentDhcpSnoopingStoreIntervalThis object indicates the perodic time interval
to save the (changed) DHCP Snooping bindings database.rw Unsigned32 .1.3.6.1.4.1.248.12.1.2.8.23.14 |
hm2AgentDhcpL2RelayConfigGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.12.1.2.8.24 |
hm2AgentDhcpL2RelayAdminModeThis object indicates whether DHCP L2 Relay
is enabled globally.
If this object is set to 'true',admin mode
is enabled globally.
If this object is set to 'false',admin mode
is disabled globally.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.248.12.1.2.8.24.1 |
hm2AgentDhcpL2RelayIfConfigTableA table provides the mechanism to enable/disable and configure
the trust state for DHCP L2Relay purpose at each physical
interface capable of this feature. SEQUENCE OF Hm2AgentDhcpL2RelayIfConfigEntry .1.3.6.1.4.1.248.12.1.2.8.24.2 |
hm2AgentDhcpL2RelayIfConfigEntryA row instance contains the configuration for
DHCP L2 Relay at each physical interface capable of this feature. Hm2AgentDhcpL2RelayIfConfigEntry .1.3.6.1.4.1.248.12.1.2.8.24.2.1 |
hm2AgentDhcpL2RelayIfEnableThis object indicates whether the DHCP L2Relay is enabled
or notrw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.248.12.1.2.8.24.2.1.1 |
hm2AgentDhcpL2RelayIfTrustEnableThis object indicates whether the interface is trusted for
DHCP L2 Relay purpose.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.248.12.1.2.8.24.2.1.2 |
hm2AgentDhcpL2RelayVlanConfigTableA table provides the mechanism to control DHCP L2 Relay
per VLAN. When a VLAN is created in a device
supporting this table, a corresponding entry of this table
will be added. SEQUENCE OF Hm2AgentDhcpL2RelayVlanConfigEntry .1.3.6.1.4.1.248.12.1.2.8.24.3 |
hm2AgentDhcpL2RelayVlanConfigEntryA row instance contains the configuration for DHCP
L2 Relay at each existing VLAN. Hm2AgentDhcpL2RelayVlanConfigEntry .1.3.6.1.4.1.248.12.1.2.8.24.3.1 |
hm2AgentDhcpL2RelayVlanIndexThis object indicates the VLAN number on which DHCP L2 Relay
feature is configured. VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.248.12.1.2.8.24.3.1.1 |
hm2AgentDhcpL2RelayVlanEnableThis object indicates whether DHCP L2 Relay is
enabled in this VLAN.
If this object is set to 'true', DHCP L2 Relay
is enabled.
If this object is set to 'false', DHCP L2 Relay
is disabled.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.248.12.1.2.8.24.3.1.2 |
hm2AgentDhcpL2RelayCircuitIdVlanEnableThis object indicates whether DHCP CircuitId is
enabled for L2 relaying in this VLAN.
If this object is set to 'true', DHCP CircuitId
is enabled.
If this object is set to 'false', DHCP CircuitId
is disabled.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.248.12.1.2.8.24.3.1.3 |
hm2AgentDhcpL2RelayRemoteIdVlanEnableWhen this object is set with a non-empty string, DHCP RemoteId is
enabled for L2 relaying in this VLAN. Notice that you can set this
object only if hm2AgentDhcpL2RelayVlanRemoteIdType is 'other'.rw DisplayString .1.3.6.1.4.1.248.12.1.2.8.24.3.1.4 |
hm2AgentDhcpL2RelayVlanRemoteIdTypeThis option determines the content of the option 82 Remote ID.
ip(1) - inserts the IP address
mac(2) - inserts the MAC adress
client-id(3) - inserts the client identifier (sysName)
other(4) - inserts the value in hm2AgentDhcpL2RelayRemoteIdVlanEnablerw Enumeration .1.3.6.1.4.1.248.12.1.2.8.24.3.1.248 |
hm2AgentDhcpL2RelayStatsResetClear the DHCP L2Relay statistics on all ports. A value of reset(1)
is used to reset the statistics. A read on this object will
always return the value none(0). The value none(0) cannot
be forcibly set by the administrator.rw Enumeration .1.3.6.1.4.1.248.12.1.2.8.24.6 |
hm2AgentDhcpL2RelayStatsTableA table provides the mechanism for statics of DHCP L2 Relay. SEQUENCE OF Hm2AgentDhcpL2RelayStatsEntry .1.3.6.1.4.1.248.12.1.2.8.24.7 |
hm2AgentDhcpL2RelayStatsEntryA row instance contains the DHCP L2Relay statistics per interface. Hm2AgentDhcpL2RelayStatsEntry .1.3.6.1.4.1.248.12.1.2.8.24.7.1 |
hm2AgentDhcpL2RelayUntrustedSrvrMsgsWithOptn82This object indicates the number of DHCP server messages received with Option-82 field
on the untrusted interface.ro Counter32 .1.3.6.1.4.1.248.12.1.2.8.24.7.1.1 |
hm2AgentDhcpL2RelayUntrustedClntMsgsWithOptn82This object indicates the number of DHCP client messages received with Option-82 field
on the untrusted interface.ro Counter32 .1.3.6.1.4.1.248.12.1.2.8.24.7.1.2 |
hm2AgentDhcpL2RelayTrustedSrvrMsgsWithoutOptn82This object indicates the number of DHCP server messages received without Option-82 field
on the trusted interface.ro Counter32 .1.3.6.1.4.1.248.12.1.2.8.24.7.1.3 |
hm2AgentDhcpL2RelayTrustedClntMsgsWithoutOptn82This object indicates the number of DHCP client messages received without Option-82 field
on the trusted interface.ro Counter32 .1.3.6.1.4.1.248.12.1.2.8.24.7.1.4 |
hm2AgentSwitchVoiceVLANGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.12.1.2.8.25 |
hm2AgentSwitchVoiceVLANAdminModeThis enables or disables Voice VLAN on the system.rw HmEnabledStatus (HM2-TC-MIB) .1.3.6.1.4.1.248.12.1.2.8.25.1 |
hm2AgentSwitchVoiceVlanDeviceTableA table of the Voice Vlan device entries. SEQUENCE OF Hm2AgentSwitchVoiceVlanDeviceEntry .1.3.6.1.4.1.248.12.1.2.8.25.2 |
hm2AgentSwitchVoiceVlanDeviceEntryRepresents entry for a Voice Device on the interface. Hm2AgentSwitchVoiceVlanDeviceEntry .1.3.6.1.4.1.248.12.1.2.8.25.2.1 |
hm2AgentSwitchVoiceVlanInterfaceNumThe interface number of this interface.ro Integer32 .1.3.6.1.4.1.248.12.1.2.8.25.2.1.1 |
hm2AgentSwitchVoiceVlanDeviceMacAddressThe Voice Device Mac addressro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.248.12.1.2.8.25.2.1.2 |
hm2AgentSdmPreferConfigGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.12.1.2.8.27 |
hm2AgentSdmPreferCurrentTemplateDisplays the current active SDM Template.ro Enumeration .1.3.6.1.4.1.248.12.1.2.8.27.1 |
hm2AgentSdmPreferNextTemplateConfigures the next active template. It will be active only after the next reboot.
To revert to the default template after the next reboot, use the option default(0).rw Enumeration .1.3.6.1.4.1.248.12.1.2.8.27.2 |
hm2AgentSdmTemplateSummaryTable OBJECT IDENTIFIER .1.3.6.1.4.1.248.12.1.2.8.28 |
hm2AgentSdmTemplateTableDisplays Switch Database Management Template Information. SEQUENCE OF Hm2AgentSdmTemplateEntry .1.3.6.1.4.1.248.12.1.2.8.28.1 |
hm2AgentSdmTemplateEntryInformation about a SDM Template table entry. Hm2AgentSdmTemplateEntry .1.3.6.1.4.1.248.12.1.2.8.28.1.1 |
hm2AgentSdmTemplateIdThe SDM Template type this instance is associated with. Enumeration .1.3.6.1.4.1.248.12.1.2.8.28.1.1.1 |
hm2AgentArpEntriesThe maximum number of entries in the IPv4 Address Resolution Protocol (ARP) cache for routing interfaces.ro Integer32 .1.3.6.1.4.1.248.12.1.2.8.28.1.1.2 |
hm2AgentIPv4UnicastRoutesThe maximum number of IPv4 unicast forwarding table entries.ro Integer32 .1.3.6.1.4.1.248.12.1.2.8.28.1.1.3 |
hm2AgentIPv6NdpEntriesThe maximum number of IPv6 Neighbor Discovery Protocol (NDP) cache entries.ro Integer32 .1.3.6.1.4.1.248.12.1.2.8.28.1.1.4 |
hm2AgentIPv6UnicastRoutesThe maximum number of IPv6 unicast forwarding table entries.ro Integer32 .1.3.6.1.4.1.248.12.1.2.8.28.1.1.5 |
hm2AgentEcmpNextHopsThe maximum number of Equal cost next hops that can be installed in the IPv4 and IPv6 unicast forwarding tables.ro Integer32 .1.3.6.1.4.1.248.12.1.2.8.28.1.1.6 |
hm2AgentIPv4MulticastRoutesThe maximum number of IPv4 multicast forwarding table entries.ro Integer32 .1.3.6.1.4.1.248.12.1.2.8.28.1.1.7 |
hm2AgentIPv6MulticastRoutesThe maximum number of IPv6 multicast forwarding table entries.ro Integer32 .1.3.6.1.4.1.248.12.1.2.8.28.1.1.8 |
hm2AgentSwitchStaticMacStatsGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.12.1.2.8.248 |
hm2AgentSwitchStaticMacEntriesTotal number of MAC addresses configured statically in mac-filter-table.ro Counter32 .1.3.6.1.4.1.248.12.1.2.8.248.1 |
hm2AgentSwitchGARPGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.12.1.2.8.249 |
hm2AgentSwitchGmrpUnknownMulticastFilterModeThis configures whether traffic from unknown multicast addresses must be flooded or be discarded.rw Enumeration .1.3.6.1.4.1.248.12.1.2.8.249.1 |
hm2AgentSwitchGmrpPortTableGMRP control and status information for a bridge port.
Augments dot1dPortGmrpEntry in P-BRIDGE-MIB. SEQUENCE OF Hm2AgentSwitchGmrpPortEntry .1.3.6.1.4.1.248.12.1.2.8.249.10 |
hm2AgentSwitchGmrpPortEntryGMRP control and status information for a bridge port.
Augments dot1dPortGmrpEntry in P-BRIDGE-MIB. Hm2AgentSwitchGmrpPortEntry .1.3.6.1.4.1.248.12.1.2.8.249.10.1 |
hm2AgentSwitchGmrpPortPktRxThe total number of GMRP packets received,
in all VLANs, on this port.ro Counter32 .1.3.6.1.4.1.248.12.1.2.8.249.10.1.1 |
hm2AgentSwitchGmrpPortPktTxThe total number of GMRP packets transmitted,
in all VLANs, on this port.ro Counter32 .1.3.6.1.4.1.248.12.1.2.8.249.10.1.2 |
hm2AgentSwitchGvrpPortTableGVRP control and status information for a bridge port.
Augments dot1qPortVlanEntry in Q-BRIDGE-MIB. SEQUENCE OF Hm2AgentSwitchGvrpPortEntry .1.3.6.1.4.1.248.12.1.2.8.249.15 |
hm2AgentSwitchGvrpPortEntryGVRP control and status information for a bridge port.
Augments dot1qPortVlanEntry in Q-BRIDGE-MIB. Hm2AgentSwitchGvrpPortEntry .1.3.6.1.4.1.248.12.1.2.8.249.15.1 |
hm2AgentSwitchGvrpPortPktRxThe total number of GVRP packets received on this port.ro Counter32 .1.3.6.1.4.1.248.12.1.2.8.249.15.1.1 |
hm2AgentSwitchGvrpPortPktTxThe total number of GVRP packets transmitted on this port.ro Counter32 .1.3.6.1.4.1.248.12.1.2.8.249.15.1.2 |
hm2AgentPortMirroringGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.12.1.2.10 |
hm2AgentPortMirrorTableThis table includes entries for each Port Mirroring session. SEQUENCE OF Hm2AgentPortMirrorEntry .1.3.6.1.4.1.248.12.1.2.10.4 |
hm2AgentPortMirrorEntryProvides configuration of a Port Mirroring session specifying the
destination port, and the source Port Mask, providing a many-to-one
mapping. Hm2AgentPortMirrorEntry .1.3.6.1.4.1.248.12.1.2.10.4.1 |
hm2AgentPortMirrorSessionNumThe Session number of this mirroring entry. The number of sessions is
fixed and platform dependant. Unsigned32 .1.3.6.1.4.1.248.12.1.2.10.4.1.1 |
hm2AgentPortMirrorDestinationPortThe port which traffic from the mirrored ports will be sent to.rw InterfaceIndexOrZero (IF-MIB) .1.3.6.1.4.1.248.12.1.2.10.4.1.2 |
hm2AgentPortMirrorSourcePortMaskThe ports from which traffic will be sent to the destination port.
The destination port can not be included in this list of ports.rw Hm2AgentPortMask .1.3.6.1.4.1.248.12.1.2.10.4.1.3 |
hm2AgentPortMirrorAdminModeThe status of this port mirroring session.
enable(1) - This session is active and all traffic from the source ports
will be mirrored to the destination port.
disable(2) - This session is not active.rw Enumeration .1.3.6.1.4.1.248.12.1.2.10.4.1.4 |
hm2AgentPortMirrorSourceVlanThe vlan from which traffic will be sent to the destination port.rw Unsigned32 .1.3.6.1.4.1.248.12.1.2.10.4.1.5 |
hm2AgentPortMirrorRemoteSourceVlanThe remote vlan from which traffic will be sent to the destination port.rw Unsigned32(0|2..4042) .1.3.6.1.4.1.248.12.1.2.10.4.1.6 |
hm2AgentPortMirrorRemoteDestinationVlanThe VLAN that forwards the network traffic to the destination switch.rw Unsigned32(0|2..4042) .1.3.6.1.4.1.248.12.1.2.10.4.1.7 |
hm2AgentPortMirrorReflectorPortThe port which traffic from the mirrored ports will be sent to in case of destination being remote VLAN.rw InterfaceIndexOrZero (IF-MIB) .1.3.6.1.4.1.248.12.1.2.10.4.1.8 |
hm2AgentPortMirrorAllowMgmtModeThe status of the management access possibility for this session.
enable(1) - Management is allowed - The device is accessible via this port and is
responsive to protocols while mirroring the probe port.
disable(2) - Management not is allowed - the device is not accessible via this port and
is not responsive to protocols. It only mirrors the probe port.rw HmEnabledStatus (HM2-TC-MIB) .1.3.6.1.4.1.248.12.1.2.10.4.1.9 |
hm2AgentPortMirrorResetRemoves, reset(2) the configuration for this session.
Returns always other(1) when read.rw Enumeration .1.3.6.1.4.1.248.12.1.2.10.4.1.248 |
hm2AgentPortMirrorTypeTableThis table includes entries for each source ports direction of port mirroring. SEQUENCE OF Hm2AgentPortMirrorTypeEntry .1.3.6.1.4.1.248.12.1.2.10.5 |
hm2AgentPortMirrorTypeEntryProvides configuration of a Port Mirroring direction specifying the
session of the port mirroring and source port. Hm2AgentPortMirrorTypeEntry .1.3.6.1.4.1.248.12.1.2.10.5.1 |
hm2AgentPortMirrorTypeSourcePortThe port from which traffic will be sent to the destination port.
This port should be a source port in the corresponding session. Unsigned32 .1.3.6.1.4.1.248.12.1.2.10.5.1.1 |
hm2AgentPortMirrorTypeTypeThe direction of the data to be mirrored on this source port.
none(0) - No configuration is set.
tx(1) - The data that is transmitted from the source port.
rx(2) - The data that is received on the source port.
txrx(3) - The data that is transmitted/received from/on the source portrw Enumeration .1.3.6.1.4.1.248.12.1.2.10.5.1.2 |
hm2AgentPortMirrorRemoteVlanThe VLAN configured as RSPAN VLAN.rw Unsigned32 .1.3.6.1.4.1.248.12.1.2.10.6 |
hm2AgentPortMirrorSNMPExtensionGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.12.1.2.10.248 |
hm2AgentPortMirrorVlanMirrorPortConflictVLAN has been already configured as a source interface. At the same time physical interface and VLAN interface cannot be configured as source interfaces for a session. OBJECT IDENTIFIER .1.3.6.1.4.1.248.12.1.2.10.248.1 |
hm2AgentPortMirrorPortVlanMirrorConflictA physical interface has been already configured as a source interface. At the same time physical interface and VLAN interface cannot be configured as source interfaces for a session. OBJECT IDENTIFIER .1.3.6.1.4.1.248.12.1.2.10.248.2 |
hm2AgentPortMirrorProbePortAlreadySetSelected interface is already used. OBJECT IDENTIFIER .1.3.6.1.4.1.248.12.1.2.10.248.3 |
hm2AgentPortMirrorProbePortVlanConflictDestination interface cannot participate in source VLAN. OBJECT IDENTIFIER .1.3.6.1.4.1.248.12.1.2.10.248.4 |
hm2AgentPortMirrorVlanNotCreatedNot existing VLAN cannot be configured as source interface for a session. OBJECT IDENTIFIER .1.3.6.1.4.1.248.12.1.2.10.248.5 |
hm2AgentPortMirrorInvalidSourcePortSelected interface () cannot be configured as source interface. OBJECT IDENTIFIER .1.3.6.1.4.1.248.12.1.2.10.248.6 |
hm2AgentPortMirrorSourcePortDestinationPortConflictDestination interface () cannot be configured as source interface. OBJECT IDENTIFIER .1.3.6.1.4.1.248.12.1.2.10.248.7 |
hm2AgentPortMirrorDestinationPortInvalidConflict with another feature: Selected interface () is already used by () and cannot be configured as a destination interface. OBJECT IDENTIFIER .1.3.6.1.4.1.248.12.1.2.10.248.8 |
hm2AgentPortMirrorVlanRspanVlanConflictRSPAN vlan () cannot be configured as source vlan. OBJECT IDENTIFIER .1.3.6.1.4.1.248.12.1.2.10.248.9 |
hm2AgentPortMirrorRemoteSourceRemoteDestinationConflictSource and destination cannot be set to remote VLAN at the same time. OBJECT IDENTIFIER .1.3.6.1.4.1.248.12.1.2.10.248.10 |
hm2AgentPortMirrorReflectorPortInvalidSelected interface () cannot be configured as a reflector interface. Only physical interface can be configured as a reflector interface. OBJECT IDENTIFIER .1.3.6.1.4.1.248.12.1.2.10.248.11 |
hm2AgentPortMirrorSourcePortReflectorPortConflictSource interface () cannot be configured as reflector interface. OBJECT IDENTIFIER .1.3.6.1.4.1.248.12.1.2.10.248.12 |
hm2AgentPortMirrorReflectorPortVlanConflictReflector interface () cannot participate in source vlan (). OBJECT IDENTIFIER .1.3.6.1.4.1.248.12.1.2.10.248.13 |
hm2AgentPortMirrorPrivateVlanConfiguredSelected VLAN is already configured as private VLAN and cannot be configured as RSPAN VLAN. OBJECT IDENTIFIER .1.3.6.1.4.1.248.12.1.2.10.248.14 |
hm2AgentPortMirrorDestinationRemotePortNotSetA destination/reflector port must first be set before mirroring/remote-mirroring can be enabled. OBJECT IDENTIFIER .1.3.6.1.4.1.248.12.1.2.10.248.15 |
hm2AgentPortMirrorRspanVlanInconsistentThe RSPAN VLAN ID is inconsistent with the RSPAN source/destination VLAN ID. OBJECT IDENTIFIER .1.3.6.1.4.1.248.12.1.2.10.248.16 |
hm2AgentPortMirrorRspanVlanIdInvalidVLAN 1 cannot be used as the RSPAN VLAN. OBJECT IDENTIFIER .1.3.6.1.4.1.248.12.1.2.10.248.17 |
hm2AgentDot3adAggPortTableThis table provides 802.3ad link aggregation information for each
physical port that is not available through the standard MIB. SEQUENCE OF Hm2AgentDot3adAggPortEntry .1.3.6.1.4.1.248.12.1.2.12 |
hm2AgentDot3adAggPortEntryInformation about a table entry. The hm2AgentDot3adAggPort identifies
the external interface number of the port. Hm2AgentDot3adAggPortEntry .1.3.6.1.4.1.248.12.1.2.12.1 |
hm2AgentDot3adAggPortifIndex of this physical portro Integer32 .1.3.6.1.4.1.248.12.1.2.12.1.1 |
hm2AgentDot3adAggPortLACPModeEnable/disable 802.3ad LACP on this portrw HmEnabledStatus (HM2-TC-MIB) .1.3.6.1.4.1.248.12.1.2.12.1.2 |
hm2AgentPortConfigTableA table of the switch's physical port config entries SEQUENCE OF Hm2AgentPortConfigEntry .1.3.6.1.4.1.248.12.1.2.13 |
hm2AgentPortConfigEntrySwitch's physical port config entry Hm2AgentPortConfigEntry .1.3.6.1.4.1.248.12.1.2.13.1 |
hm2AgentPortDot1dBasePortThe number of this port.ro Integer32 .1.3.6.1.4.1.248.12.1.2.13.1.1 |
hm2AgentPortIfIndexThe switchs Port IfIndex.ro Integer32 .1.3.6.1.4.1.248.12.1.2.13.1.2 |
hm2AgentPortClearStatsClear stats for this port only.rw HmEnabledStatus (HM2-TC-MIB) .1.3.6.1.4.1.248.12.1.2.13.1.10 |
hm2AgentPortDot3FlowControlModeConfig flowcontrol allows you to enable or disable
802.3x flow control for this port. This value
applies to only full-duplex mode ports. Enabling
symmetric flow control allows the port to send
and receive pause frames. Enabling asymmetric
flow control allows the port to receive pause
frames but it will not transmit pause frames.rw Enumeration .1.3.6.1.4.1.248.12.1.2.13.1.14 |
hm2AgentPortMaxFrameSizeLimitThis object identifies the largest value that can be
configured for hm2AgentPortMaxFrameSize.ro Integer32 .1.3.6.1.4.1.248.12.1.2.13.1.18 |
hm2AgentPortMaxFrameSizeThis object identifies the currently configured maximum frame size
value for this port. The maximum value that this object can be set
to is the value of hm2AgentPortMaxFrameSizeLimit. For Ethernet ports
which support 802.1Q vlan tagging, the minimum value that this object
can be set to is 1522rw Integer32 .1.3.6.1.4.1.248.12.1.2.13.1.19 |
hm2AgentPortBroadcastControlModeIf enabled, broadcast storm recovery will function on this port.
When you specify Enable for Broadcast Storm Recovery and the broadcast
traffic on this Ethernet port exceeds the configured threshold, the
switch blocks (discards) the broadcast traffic.rw HmEnabledStatus (HM2-TC-MIB) .1.3.6.1.4.1.248.12.1.2.13.1.20 |
hm2AgentPortBroadcastControlThresholdConfigures the broadcast storm recovery threshold for this port
as a percentage of port speed or as an absolute pps rate.rw Integer32 .1.3.6.1.4.1.248.12.1.2.13.1.21 |
hm2AgentPortMulticastControlModeIf enabled, multicast storm recovery will function on this port.
When you specify Enable for Multicast Storm Recovery and the multicast
traffic on this Ethernet port exceeds the configured threshold, the
switch blocks (discards) the multicast traffic.rw HmEnabledStatus (HM2-TC-MIB) .1.3.6.1.4.1.248.12.1.2.13.1.22 |
hm2AgentPortMulticastControlThresholdConfigures the multicast storm recovery threshold for this port
as a percentage of port speed or as an absolute pps rate.rw Integer32 .1.3.6.1.4.1.248.12.1.2.13.1.23 |
hm2AgentPortUnicastControlModeIf enabled, unicast storm recovery will function on this port.
When you specify Enable for Unicast Storm Recovery and the unknown unicast
traffic on this Ethernet port exceeds the configured threshold, the
switch blocks (discards) the unknown unicast traffic.rw HmEnabledStatus (HM2-TC-MIB) .1.3.6.1.4.1.248.12.1.2.13.1.24 |
hm2AgentPortUnicastControlThresholdConfigures the unicast storm recovery threshold for this port
as a percentage of port speed or as an absolute pps rate.rw Integer32 .1.3.6.1.4.1.248.12.1.2.13.1.25 |
hm2AgentPortBroadcastControlThresholdUnitConfigures the units of the threshold value to percentage of
port speed or absolute packets per second.rw Enumeration .1.3.6.1.4.1.248.12.1.2.13.1.26 |
hm2AgentPortMulticastControlThresholdUnitConfigures the units of the threshold value to percentage of
port speed or absolute packets per second.rw Enumeration .1.3.6.1.4.1.248.12.1.2.13.1.27 |
hm2AgentPortUnicastControlThresholdUnitConfigures the units of the threshold value to percentage of
port speed or absolute packets per second.rw Enumeration .1.3.6.1.4.1.248.12.1.2.13.1.28 |
hm2AgentPortVoiceVlanModeDescribes and Configures the Port Voice VLAN Mode. This object
can only be set to disable(5).rw Enumeration .1.3.6.1.4.1.248.12.1.2.13.1.29 |
hm2AgentPortVoiceVlanIDDescribes and Configures the Port Voice VLAN ID
if the Voice Vlan Mode is Vlan ID.rw Integer32 .1.3.6.1.4.1.248.12.1.2.13.1.30 |
hm2AgentPortVoiceVlanPriorityDescribes and Configures the Port Voice VLAN Priority
if the Voice Vlan Mode is dot1p. A value of 255 indicates
that the priority is not configured.rw Integer32 (0..7|255) .1.3.6.1.4.1.248.12.1.2.13.1.31 |
hm2AgentPortVoiceVlanDataPriorityModeDescribes and Configures the Port Voice VLAN Data Priority Mode.rw Enumeration .1.3.6.1.4.1.248.12.1.2.13.1.32 |
hm2AgentPortVoiceVlanOperationalStatusDescribes the Port Voice VLAN Operational Status.ro Enumeration .1.3.6.1.4.1.248.12.1.2.13.1.33 |
hm2AgentPortVoiceVlanUntaggedDescribes and Configures the Port Voice VLAN tagging mode.rw Enumeration .1.3.6.1.4.1.248.12.1.2.13.1.34 |
hm2AgentPortVoiceVlanNoneModeDescribes and Configures the Port Voice VLAN None mode.rw Enumeration .1.3.6.1.4.1.248.12.1.2.13.1.35 |
hm2AgentPortVoiceVlanDSCPDescribes and Configures the Port Voice VLAN DSCP value.rw Integer32 .1.3.6.1.4.1.248.12.1.2.13.1.36 |
hm2AgentPortVoiceVlanAuthModeDescribes and Configures the Port Voice VLAN Authentication mode.
Disable means authentication not required for voice devices when dot1x is enabled.rw HmEnabledStatus (HM2-TC-MIB) .1.3.6.1.4.1.248.12.1.2.13.1.37 |
hm2AgentPortDot3FlowControlOperStatusThis object identifies operational status of the flow control per port.ro Enumeration .1.3.6.1.4.1.248.12.1.2.13.1.38 |
hm2AgentPortSfpLinkLossAlertIf enabled, this object helps in the detecting the loss of a SFP link by
deactivating its light.rw HmEnabledStatus (HM2-TC-MIB) .1.3.6.1.4.1.248.12.1.2.13.1.248 |
hm2AgentProtocolConfigGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.12.1.2.14 |
hm2AgentProtocolGroupTableA table of the switch's Protocol-based VLAN entries SEQUENCE OF Hm2AgentProtocolGroupEntry .1.3.6.1.4.1.248.12.1.2.14.2 |
hm2AgentProtocolGroupEntrySwitch's Protocol-based VLAN entry Hm2AgentProtocolGroupEntry .1.3.6.1.4.1.248.12.1.2.14.2.1 |
hm2AgentProtocolGroupIdGroup identifier of the Protocol-based VLAN entry. Integer32 .1.3.6.1.4.1.248.12.1.2.14.2.1.1 |
hm2AgentProtocolGroupNameGroup name of the Protocol-based VLAN entry.rw DisplayString .1.3.6.1.4.1.248.12.1.2.14.2.1.2 |
hm2AgentProtocolGroupVlanIdVLAN associated with the Protocol-based VLAN entry. Set to 0 to remove.rw Integer32 .1.3.6.1.4.1.248.12.1.2.14.2.1.3 |
hm2AgentProtocolGroupStatusThe status of the Protocol-based VLAN entry.
active(1) - this entry is active
createAndGo(4) - used to create a new entry
destroy(6) - remove this entryrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.248.12.1.2.14.2.1.7 |
hm2AgentProtocolGroupPortTableA table of the switch's physical port config entries SEQUENCE OF Hm2AgentProtocolGroupPortEntry .1.3.6.1.4.1.248.12.1.2.14.3 |
hm2AgentProtocolGroupPortEntrySwitch's physical port config entry Hm2AgentProtocolGroupPortEntry .1.3.6.1.4.1.248.12.1.2.14.3.1 |
hm2AgentProtocolGroupPortIfIndexThe interface number of this instance.ro Integer32 .1.3.6.1.4.1.248.12.1.2.14.3.1.1 |
hm2AgentProtocolGroupPortStatusThe status of this entry.
active(1) - the port is associated with this group
createAndGo(4) - add the port to this group
createAndWait(5) - add the port to this group
destroy(6) - remove the port from this grouprw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.248.12.1.2.14.3.1.2 |
hm2AgentProtocolGroupProtocolTableA table of the switch's physical port config entries SEQUENCE OF Hm2AgentProtocolGroupProtocolEntry .1.3.6.1.4.1.248.12.1.2.14.4 |
hm2AgentProtocolGroupProtocolEntrySwitch's physical port config entry Hm2AgentProtocolGroupProtocolEntry .1.3.6.1.4.1.248.12.1.2.14.4.1 |
hm2AgentProtocolGroupProtocolIDThe protocol ID of this instance. The value for IP is 2048 (0x0800), ARP is 2054 (0x0806) and IPX is 33079 (0x8137).
Other protocol Ids in the range 1536 to 65535 can also be configured. Integer32 .1.3.6.1.4.1.248.12.1.2.14.4.1.1 |
hm2AgentProtocolGroupProtocolStatusThe status of this entry.
active(1) - the port is associated with this group
createAndGo(4) - add the port to this group
createAndWait(5) - add the port to this group
destroy(6) - remove the port from this grouprw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.248.12.1.2.14.4.1.2 |
hm2AgentStpSwitchConfigGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.12.1.2.15 |
hm2AgentStpConfigDigestKeyThe MST configuration digest key.ro OCTET STRING .1.3.6.1.4.1.248.12.1.2.15.1 |
hm2AgentStpConfigFormatSelectorThe MST configuration format selector. A value other than 0 (zero)
indicates non-support for the IEEE 802.1s standard.ro Unsigned32 .1.3.6.1.4.1.248.12.1.2.15.2 |
hm2AgentStpConfigNameThe MST configuration name of at most 32 characters.rw DisplayString .1.3.6.1.4.1.248.12.1.2.15.3 |
hm2AgentStpConfigRevisionThe MST configuration revision. The default value is 1.rw Unsigned32 .1.3.6.1.4.1.248.12.1.2.15.4 |
hm2AgentStpForceVersionThe MST configuration force protocol version. The default version is RSTP.rw Enumeration .1.3.6.1.4.1.248.12.1.2.15.5 |
hm2AgentStpAdminModeThe spanning tree operational status.
enable(1) - enables spanning tree operational status on the switch.
disable(2) - disables spanning tree operational status on the switch.
The default status is enabled.rw HmEnabledStatus (HM2-TC-MIB) .1.3.6.1.4.1.248.12.1.2.15.6 |
hm2AgentStpPortTableSTP port table. SEQUENCE OF Hm2AgentStpPortEntry .1.3.6.1.4.1.248.12.1.2.15.7 |
hm2AgentStpPortEntrySTP port entry. Hm2AgentStpPortEntry .1.3.6.1.4.1.248.12.1.2.15.7.1 |
hm2AgentStpPortStateThe administrative STP state for the port.
enable(1) - enables STP on the port.
disable(2) - disables STP on the port.
The default port STP state is enabled for the first 4095
ports and disabled for any ports beyond.rw HmEnabledStatus (HM2-TC-MIB) .1.3.6.1.4.1.248.12.1.2.15.7.1.1 |
hm2AgentStpPortStatsMstpBpduRxThe MSTP BPDUs received on a specific port.ro Counter32 .1.3.6.1.4.1.248.12.1.2.15.7.1.2 |
hm2AgentStpPortStatsMstpBpduTxThe MSTP BPDUs sent from a specific port.ro Counter32 .1.3.6.1.4.1.248.12.1.2.15.7.1.3 |
hm2AgentStpPortStatsRstpBpduRxThe RSTP BPDUs received on a specific port.ro Counter32 .1.3.6.1.4.1.248.12.1.2.15.7.1.4 |
hm2AgentStpPortStatsRstpBpduTxThe RSTP BPDUs sent from a specific port.ro Counter32 .1.3.6.1.4.1.248.12.1.2.15.7.1.5 |
hm2AgentStpPortStatsStpBpduRxThe STP BPDUs received on a specific port.ro Counter32 .1.3.6.1.4.1.248.12.1.2.15.7.1.6 |
hm2AgentStpPortStatsStpBpduTxThe STP BPDUs sent from a specific port.ro Counter32 .1.3.6.1.4.1.248.12.1.2.15.7.1.7 |
hm2AgentStpPortUpTimeTime since port was reset.
It is displayed in days, hours, minutes, and seconds.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.248.12.1.2.15.7.1.8 |
hm2AgentStpPortMigrationCheckForce the specified port to transmit RSTP or MSTP BPDUs.
Supported values:
false(0) - BPDUs are not to be transmitted.
true(1) - BPDUs are to be transmitted
A non-zero value indicates that BPDUs are to be sent on the specified port.rw Enumeration .1.3.6.1.4.1.248.12.1.2.15.7.1.9 |
hm2AgentStpCstConfigGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.12.1.2.15.8 |
hm2AgentStpCstHelloTimeThe MSTP root port hello time for the CIST.ro Unsigned32 .1.3.6.1.4.1.248.12.1.2.15.8.1 |
hm2AgentStpCstMaxAgeThe MSTP root port max age for the CIST.ro Unsigned32 .1.3.6.1.4.1.248.12.1.2.15.8.2 |
hm2AgentStpCstRegionalRootIdThe MSTP regional root identifier for the CIST.ro OCTET STRING .1.3.6.1.4.1.248.12.1.2.15.8.3 |
hm2AgentStpCstRegionalRootPathCostThe MSTP regional root path cost for the CIST.ro Unsigned32 .1.3.6.1.4.1.248.12.1.2.15.8.4 |
hm2AgentStpCstRootFwdDelayThe MSTP root port forward delay for the CIST.ro Unsigned32 .1.3.6.1.4.1.248.12.1.2.15.8.5 |
hm2AgentStpCstBridgeFwdDelayThe MSTP bridge forward delay for the CIST. The default value is 15.rw Unsigned32 .1.3.6.1.4.1.248.12.1.2.15.8.6 |
hm2AgentStpCstBridgeHelloTimeThe MSTP bridge hello time for the CIST. The default
value is 2.rw Unsigned32 .1.3.6.1.4.1.248.12.1.2.15.8.7 |
hm2AgentStpCstBridgeHoldTimeThe MSTP bridge hold time for the CIST.ro Unsigned32 .1.3.6.1.4.1.248.12.1.2.15.8.8 |
hm2AgentStpCstBridgeMaxAgeThe MSTP bridge max age for the CIST. The default value is 20.rw Unsigned32 .1.3.6.1.4.1.248.12.1.2.15.8.9 |
hm2AgentStpCstBridgeMaxHopsThe MSTP bridge max hops for the CIST. The default value is 20.rw Unsigned32 .1.3.6.1.4.1.248.12.1.2.15.8.10 |
hm2AgentStpCstBridgePriorityThe MSTP bridge priority for the CIST. The default value is 32768.rw Unsigned32 .1.3.6.1.4.1.248.12.1.2.15.8.11 |
hm2AgentStpCstBridgeHoldCountThe MSTP bridge hold count for the CIST. This command sets the value of
maximum bpdus that a bridge is allowed to send within a hello time window.
The default value is 10.rw Unsigned32 .1.3.6.1.4.1.248.12.1.2.15.8.12 |
hm2AgentStpCstPortTableCIST port table. SEQUENCE OF Hm2AgentStpCstPortEntry .1.3.6.1.4.1.248.12.1.2.15.9 |
hm2AgentStpCstPortEntryCIST port entry. Hm2AgentStpCstPortEntry .1.3.6.1.4.1.248.12.1.2.15.9.1 |
hm2AgentStpCstPortOperEdgeThe MSTP operational status of a specific port for the CIST.ro HmEnabledStatus (HM2-TC-MIB) .1.3.6.1.4.1.248.12.1.2.15.9.1.1 |
hm2AgentStpCstPortOperPointToPointThe MSTP operational point to point mac of a specific port for the CIST.ro Enumeration .1.3.6.1.4.1.248.12.1.2.15.9.1.2 |
hm2AgentStpCstPortTopologyChangeAckThe MSTP topology change acknowledge for a specific port in the CIST.ro Enumeration .1.3.6.1.4.1.248.12.1.2.15.9.1.3 |
hm2AgentStpCstPortEdgeThe administrative state of a specific port in CIST.
enable(1) - enables the port.
disable(2) - disables the port.
The default port state is disabled.rw HmEnabledStatus (HM2-TC-MIB) .1.3.6.1.4.1.248.12.1.2.15.9.1.4 |
hm2AgentStpCstPortForwardingStateThe MSTP forwarding state of a specific port in CIST.ro Enumeration .1.3.6.1.4.1.248.12.1.2.15.9.1.5 |
hm2AgentStpCstPortIdThe MSTP port identifier of a specific port in CIST.ro OCTET STRING .1.3.6.1.4.1.248.12.1.2.15.9.1.6 |
hm2AgentStpCstPortPathCostThe MSTP port path cost in CIST. The default value will
correspond to the recommendation specified in IEEE 802.1s Table 13-2
which varies depending upon link speed.rw Unsigned32 .1.3.6.1.4.1.248.12.1.2.15.9.1.7 |
hm2AgentStpCstPortPriorityThe MSTP port priority in CIST. The priority is
in the increments of 16. The default value is 128.rw Unsigned32 .1.3.6.1.4.1.248.12.1.2.15.9.1.8 |
hm2AgentStpCstDesignatedBridgeIdThe MSTP designated bridge ID of a specific port in CIST.ro OCTET STRING .1.3.6.1.4.1.248.12.1.2.15.9.1.9 |
hm2AgentStpCstDesignatedCostThe MSTP designated cost of a specific port in CIST.ro Unsigned32 .1.3.6.1.4.1.248.12.1.2.15.9.1.10 |
hm2AgentStpCstDesignatedPortIdThe MSTP designated port ID of a specific port in CIST.ro OCTET STRING .1.3.6.1.4.1.248.12.1.2.15.9.1.11 |
hm2AgentStpCstExtPortPathCostThe MSTP external port path cost in CIST. The default value varies depending upon the link speed.rw Unsigned32 .1.3.6.1.4.1.248.12.1.2.15.9.1.12 |
hm2AgentStpCstPortBpduGuardEffectBPDU Guard Mode effect on the port.
enable(1) - BPDU Guard Mode is enabled on the port.
disable(2) - BPDU Guard Mode is disabled on the port.ro HmEnabledStatus (HM2-TC-MIB) .1.3.6.1.4.1.248.12.1.2.15.9.1.13 |
hm2AgentStpCstPortBpduFilterThis command sets BPDU Filter mode on the port.
enable(1) - BPDU Filter Mode is enabled on the port.
disable(2) - BPDU Filter Mode is disabled on the port.rw HmEnabledStatus (HM2-TC-MIB) .1.3.6.1.4.1.248.12.1.2.15.9.1.14 |
hm2AgentStpCstPortBpduFloodThis command sets BPDU Flood mode on the port.
enable(1) - BPDU Flood Mode is enabled on the port.
disable(2) - BPDU Flood Mode is disabled on the port.rw HmEnabledStatus (HM2-TC-MIB) .1.3.6.1.4.1.248.12.1.2.15.9.1.15 |
hm2AgentStpCstPortAutoEdgeThis command sets the auto-edge mode of the port which enables it
to become an edge port if it does not see BPDUs for some duration.
enable(1) - enables the auto-edge mode for the port.
disable(2) - disables the auto-edge mode for the port.
The default auto-edge mode is enabled.rw HmEnabledStatus (HM2-TC-MIB) .1.3.6.1.4.1.248.12.1.2.15.9.1.16 |
hm2AgentStpCstPortRootGuardThis command sets a port to discard any superior information
received by the port and thus protect against root of the device
from changing.The port gets put into discarding state and does
not forward any packets.
enable(1) - enables the root guard mode for the port.
disable(2) - disables the root guard mode for the port.
The default root guard mode is disabled.rw HmEnabledStatus (HM2-TC-MIB) .1.3.6.1.4.1.248.12.1.2.15.9.1.17 |
hm2AgentStpCstPortTCNGuardThis command restricts the port from propagating any topology change
information received through that port.
enable(1) - enables the TCN guard mode for the port.
disable(2) - disables the TCN guard mode for the port.
The default TCN guard mode is disabled.rw HmEnabledStatus (HM2-TC-MIB) .1.3.6.1.4.1.248.12.1.2.15.9.1.18 |
hm2AgentStpCstPortLoopGuardThis command enables loop guard on this port. This setting applies
to all Spanning Tree instances of which this port is a member.
enable(1) - enables the loop guard mode for the port.
disable(2) - disables the loop guard mode for the port.
The default loop guard mode is disabled.rw HmEnabledStatus (HM2-TC-MIB) .1.3.6.1.4.1.248.12.1.2.15.9.1.19 |
hm2AgentStpMstTableMST table. SEQUENCE OF Hm2AgentStpMstEntry .1.3.6.1.4.1.248.12.1.2.15.10 |
hm2AgentStpMstEntryMST entry. Hm2AgentStpMstEntry .1.3.6.1.4.1.248.12.1.2.15.10.1 |
hm2AgentStpMstIdThe MSTP instance ID.ro Unsigned32 .1.3.6.1.4.1.248.12.1.2.15.10.1.1 |
hm2AgentStpMstBridgePriorityThe MSTP bridge priority in a specific instance. The priority is
in the increments of 4096. The recommended default value is 32768.rw Unsigned32 .1.3.6.1.4.1.248.12.1.2.15.10.1.2 |
hm2AgentStpMstBridgeIdentifierThe MSTP bridge identifier in a specific instance.ro OCTET STRING .1.3.6.1.4.1.248.12.1.2.15.10.1.3 |
hm2AgentStpMstDesignatedRootIdThe MSTP designated root bridge identifier in a specific instance.ro OCTET STRING .1.3.6.1.4.1.248.12.1.2.15.10.1.4 |
hm2AgentStpMstRootPathCostThe MSTP root path cost in a specific instance.ro Unsigned32 .1.3.6.1.4.1.248.12.1.2.15.10.1.5 |
hm2AgentStpMstRootPortIdThe MSTP root port ID in a specific instance.ro OCTET STRING .1.3.6.1.4.1.248.12.1.2.15.10.1.6 |
hm2AgentStpMstTimeSinceTopologyChangeThe MSTP time since the last topology change in a specific instance.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.248.12.1.2.15.10.1.7 |
hm2AgentStpMstTopologyChangeCountThe MSTP count of topology changes in a specific instance.ro Counter32 .1.3.6.1.4.1.248.12.1.2.15.10.1.8 |
hm2AgentStpMstTopologyChangeParmThe MSTP topology change parameter in a specific instance.ro Enumeration .1.3.6.1.4.1.248.12.1.2.15.10.1.9 |
hm2AgentStpMstRowStatusThe MSTP instance status.
Supported values:
active(1) - valid instance.
notReady(3) - row has incomplete values.
createAndGo(4) - used to create a new instance.
destroy(6) - removes an instance.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.248.12.1.2.15.10.1.10 |
hm2AgentStpMstPortTableMST port table. SEQUENCE OF Hm2AgentStpMstPortEntry .1.3.6.1.4.1.248.12.1.2.15.11 |
hm2AgentStpMstPortEntryMST port entry. Hm2AgentStpMstPortEntry .1.3.6.1.4.1.248.12.1.2.15.11.1 |
hm2AgentStpMstPortForwardingStateThe MSTP forwarding state of a specific port in a specific instance.ro Enumeration .1.3.6.1.4.1.248.12.1.2.15.11.1.1 |
hm2AgentStpMstPortIdThe MSTP port identifier of a specific port in a specific instance.ro OCTET STRING .1.3.6.1.4.1.248.12.1.2.15.11.1.2 |
hm2AgentStpMstPortPathCostThe MSTP port path cost in a specific instance. The default value will
correspond to the recommendation specified in IEEE 802.1s Table 13-2
which varies depending upon link speed.rw Unsigned32 .1.3.6.1.4.1.248.12.1.2.15.11.1.3 |
hm2AgentStpMstPortPriorityThe MSTP port priority in a specific instance. The priority is
in the increments of 16. The default value is 128.rw Unsigned32 .1.3.6.1.4.1.248.12.1.2.15.11.1.4 |
hm2AgentStpMstDesignatedBridgeIdThe MSTP designated bridge ID of a specific port in a specific instance.ro OCTET STRING .1.3.6.1.4.1.248.12.1.2.15.11.1.5 |
hm2AgentStpMstDesignatedCostThe MSTP designated cost of a specific port in a specific instance.ro Unsigned32 .1.3.6.1.4.1.248.12.1.2.15.11.1.6 |
hm2AgentStpMstDesignatedPortIdThe MSTP designated port ID of a specific port in a specific instance.ro OCTET STRING .1.3.6.1.4.1.248.12.1.2.15.11.1.7 |
hm2AgentStpMstPortLoopInconsistentStateThe loop inconsistent state of a specific port in a specific instance.
This value can only report as true(1) when loop guard is enabled on the port
and the port has transitioned from blocking state in this MST instance.ro Enumeration .1.3.6.1.4.1.248.12.1.2.15.11.1.8 |
hm2AgentStpMstPortTransitionsIntoLoopInconsistentStateThe number of times this interface has transitioned into loop inconsistent state.ro Counter32 .1.3.6.1.4.1.248.12.1.2.15.11.1.9 |
hm2AgentStpMstPortTransitionsOutOfLoopInconsistentStateThe number of times this interface has transitioned out of loop inconsistent state.ro Counter32 .1.3.6.1.4.1.248.12.1.2.15.11.1.10 |
hm2AgentStpMstPortRoleThe current port pole for a specific port (i.e., root, alternate, designated or backup) in a specific instance.ro Enumeration .1.3.6.1.4.1.248.12.1.2.15.11.1.248 |
hm2AgentStpCstAutoPortPathCostThe Spanning Tree auto port path cost. If the value is true, the port
path cost will be calculated depending on link speed corresponding to the
recommendation specified in IEEE 802.1s Table 13-2 which varies depending
upon link speed.ro Enumeration .1.3.6.1.4.1.248.12.1.2.15.11.1.249 |
hm2AgentStpMstPortReceivedBridgeIdThe received bridge ID on a specific port in a specific instance.ro OCTET STRING .1.3.6.1.4.1.248.12.1.2.15.11.1.250 |
hm2AgentStpMstPortReceivedRPCThe received root path cost of a specific port in a specific instance.ro Unsigned32 .1.3.6.1.4.1.248.12.1.2.15.11.1.251 |
hm2AgentStpMstPortReceivedPortIdThe received port ID on a specific port in a specific instance.ro OCTET STRING .1.3.6.1.4.1.248.12.1.2.15.11.1.252 |
hm2AgentStpMstAutoPortPathCostThe Spanning Tree auto port path cost of a given instance. If the value
is true, the port path cost will be calculated depending on link speed
corresponding to the recommendation specified in IEEE 802.1s Table 13-2
which varies depending upon link speed.ro Enumeration .1.3.6.1.4.1.248.12.1.2.15.11.1.253 |
hm2AgentStpMstPortReceivedRegionalRPCThe received regional (internal) root path cost of a specific port in a specific instance.ro Unsigned32 .1.3.6.1.4.1.248.12.1.2.15.11.1.254 |
hm2AgentStpMstVlanTableMST VLAN table. SEQUENCE OF Hm2AgentStpMstVlanEntry .1.3.6.1.4.1.248.12.1.2.15.12 |
hm2AgentStpMstVlanEntryMST VLAN entry. Hm2AgentStpMstVlanEntry .1.3.6.1.4.1.248.12.1.2.15.12.1 |
hm2AgentStpMstVlanRowStatusThe association status of an MSTP instance and a VLAN.
Supported values:
active(1) - valid association between an MSTP instance and a VLAN.
notReady(3) - inconsistent values for the the association between an MSTP instance and a VLAN (VLAN it's not created or version is not MSTP).
createAndGo(4) - used to create a new association between an MSTP instance and a VLAN.
destroy(6) - removes the association between an MSTP instance and a VLAN.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.248.12.1.2.15.12.1.1 |
hm2AgentStpBpduGuardModeThe spanning tree BPDU Guard Mode.
enable(1) - enables BPDU Guard Mode on the switch.
disable(2) - disables BPDU Guard Mode on the switch.
The default status is disabled.rw HmEnabledStatus (HM2-TC-MIB) .1.3.6.1.4.1.248.12.1.2.15.13 |
hm2AgentStpBpduFilterDefaultThe spanning tree BPDU Filter Mode, it enables BPDU Filter on all
edge ports.
enable(1) - enables BPDU Filter Mode on the switch.
disable(2) - disables BPDU Filter Mode on the switch.
The default status is disabled.rw HmEnabledStatus (HM2-TC-MIB) .1.3.6.1.4.1.248.12.1.2.15.14 |
hm2AgentStpRingOnlyModeWhen RSTP Ring Only Mode is enabled the switch ignores the BPDUs age on Ring Only Mode ports.
The topology change BPDUs sent on Ring Only Mode ports will have a message age of 1.
enable(1) - enables RSTP Ring Only Mode globally.
disable(2) - disables RSTP Ring Only Mode globally.
The default status is disabled.rw HmEnabledStatus (HM2-TC-MIB) .1.3.6.1.4.1.248.12.1.2.15.248 |
hm2AgentStpRingOnlyModeIntfOneInterface index of the first interface.rw InterfaceIndexOrZero (IF-MIB) .1.3.6.1.4.1.248.12.1.2.15.249 |
hm2AgentStpRingOnlyModeIntfTwoInterface index of the second interface.rw InterfaceIndexOrZero (IF-MIB) .1.3.6.1.4.1.248.12.1.2.15.250 |
hm2AgentStpMstSNMPExtensionGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.12.1.2.15.260 |
hm2AgentStpMstInstanceVlanErrorReturnInvalid value for instance. Instance 0 is a system managed instance and the user should not modify it. OBJECT IDENTIFIER .1.3.6.1.4.1.248.12.1.2.15.260.1 |
hm2AgentStpCstFwdDelayErrorReturnInvalid value combination for Max Age/Forward Delay. OBJECT IDENTIFIER .1.3.6.1.4.1.248.12.1.2.15.260.2 |
hm2AgentStpMstSwitchVersionConflictCannot switch version while spanning-tree is disabled. OBJECT IDENTIFIER .1.3.6.1.4.1.248.12.1.2.15.260.3 |
hm2AgentClassOfServiceGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.12.1.2.17 |
hm2AgentClassOfServicePortTableA table that contains information about the 802.1p priority
mapping to traffic class priority queue for every physical port. SEQUENCE OF Hm2AgentClassOfServicePortEntry .1.3.6.1.4.1.248.12.1.2.17.1 |
hm2AgentClassOfServicePortEntryA 802.1p priority mapped to a traffic class priority queue. Hm2AgentClassOfServicePortEntry .1.3.6.1.4.1.248.12.1.2.17.1.1 |
hm2AgentClassOfServicePortPriorityThe Priority value determined for the received frame.
This value is equivalent to the priority indicated in
the tagged frame received, or one of the evaluated
priorities, determined according to the media type.
For untagged frames received from Ethernet media, this
value is equal to the dot1dPortDefaultUserPriority value
for the ingress port. Integer32 .1.3.6.1.4.1.248.12.1.2.17.1.1.1 |
hm2AgentClassOfServicePortClassTraffic class priority queue the received frame is mapped to.rw Integer32 .1.3.6.1.4.1.248.12.1.2.17.1.1.2 |
hm2AgentSystemGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.12.1.3 |
hm2AgentClearVlanclear vlan entriesrw HmEnabledStatus (HM2-TC-MIB) .1.3.6.1.4.1.248.12.1.3.9 |