HMPRIV-MGMT-SNMP-MIB
The Hirschmann Private MIB definitions for Platform devices.
Main OID:
hmConfiguration.1.3.6.1.4.1.248.14
886
Objects
Active
Status
7
Dependencies
Imported Objects
Objects
886 total| Object Name |
|---|
hirschmann OBJECT IDENTIFIER .1.3.6.1.4.1.248 |
hmConfigurationThe Hirschmann Private MIB definitions for Platform devices. MODULE-IDENTITY .1.3.6.1.4.1.248.14 |
hmChassis OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.1 |
hmChassisEventThe events of hmChassis. OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.1.0 |
hmGroupMapChangeThis trap is sent when a change occurs in the group
structure of a switch. This occurs only when a
group is logically removed from or added to a switch.
The varBind list contains the updated value of the
hmSysGroupMap variable. hmNeighbourSlot identifies the
related slot. hmNeighbourIpAddress shows whether a group
was logically removed (0.0.0.0) or added (correct ipAddress). NOTIFICATION-TYPE .1.3.6.1.4.1.248.14.1.0.1 |
hmPowerSupplyThis trap is sent if the state of a power supply unit changes. NOTIFICATION-TYPE .1.3.6.1.4.1.248.14.1.0.2 |
hmFanThis trap is sent if the value of hmFanCtrl changes. NOTIFICATION-TYPE .1.3.6.1.4.1.248.14.1.0.3 |
hmSignallingRelayThis trap is sent if the value of hmRS2SigRelayState changes its value.
Variables included in this trap are hmRS2SigRelayState, hmSigTrapReason,
hmSigReasonIndex. NOTIFICATION-TYPE .1.3.6.1.4.1.248.14.1.0.4 |
hmStandbyThis trap is sent if the value of hmRS2OperMode changes. NOTIFICATION-TYPE .1.3.6.1.4.1.248.14.1.0.5 |
hmSelftestErrorThis trap is sent if the value of one of the selftest
results is not zero or if a value changes while the
agent is running. NOTIFICATION-TYPE .1.3.6.1.4.1.248.14.1.0.6 |
hmModuleMapChangeThis trap is sent when a change occurs in the module
structure of a switch. This occurs only when a
module is logically removed from or added to a switch.
The varBind list contains the updated value of the
variable hmSysGroupModuleMap. NOTIFICATION-TYPE .1.3.6.1.4.1.248.14.1.0.7 |
hmBPDUGuardTrapThis trap is sent if on this port an BPDU guard
functionality is enabled (globally or only for this port)
and an (R)STP BPDU are received on this port. That means when
hmIfaceStpBpduGuardStatus is set to true(1) for this port.
Then IfAdminStatus for this port is set to down(2).
If needed, it must be changed by hand to up(1) NOTIFICATION-TYPE .1.3.6.1.4.1.248.14.1.0.8 |
hmSigConRelayChangeThis trap is sent if the value of hmSigConOperState changes its value.
Variables included in this trap are hmSigConOperState, hmSigConTrapCause,
hmSigConTrapCauseIndex. NOTIFICATION-TYPE .1.3.6.1.4.1.248.14.1.0.10 |
hmSFPChangeTrapThis trap is sent when a SFP has been added or removed.
It is also sent for an otherwise unsupported SFP. NOTIFICATION-TYPE .1.3.6.1.4.1.248.14.1.0.11 |
hmIfaceUtilizationTrapThis trap is sent if the value of hmIfaceUtilization exceeds or
falls back below the interface untilization threshholds
hmIfaceUtilizationAlarmConditionThreshold and
hmIfaceUtilizationAlarmRemovalThreshold. NOTIFICATION-TYPE .1.3.6.1.4.1.248.14.1.0.12 |
hmDevMonStateChangeThis trap is sent if the value of hmDevMonSwitchState changes its value.
Variables included in this trap are hmDevMonSwitchState, hmDevMonTrapCause,
hmDevMonTrapCauseIndex. NOTIFICATION-TYPE .1.3.6.1.4.1.248.14.1.0.13 |
hmSFPRxPowerChangeTrapThis trap is sent when the state of the rx power of a SFP changes. NOTIFICATION-TYPE .1.3.6.1.4.1.248.14.1.0.14 |
hmSysSelftestRebootOnErrorTrapThis trap is sent when the agent wants to reboot due to an internal circumstance. NOTIFICATION-TYPE .1.3.6.1.4.1.248.14.1.0.15 |
hmSystemTable OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.1.1 |
hmSysProductManufacturer-defined product identifier.ro Enumeration .1.3.6.1.4.1.248.14.1.1.1 |
hmSysVersionThis value is a string that contains at least the
following data :
SW: Version number of software
CH: Version number of chassis
BP: Version number of backplanero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.248.14.1.1.2 |
hmSysGroupCapacityThe hmSysGroupCapacity is the number of groups that can
be contained within the chassis. Within each managed
chassis/switch, the groups are uniquely numbered in the
range from 1 to hmSysGroupCapacity.
Some groups may not be present in the chassis, in which
case the actual number of groups present will be less than
hmSysGroupCapacity. The number of groups present will never be
greater than hmSysGroupCapacity.ro Integer32 .1.3.6.1.4.1.248.14.1.1.3 |
hmSysGroupMapThis string represents the current configuration of the chassis,
encoded as an octet string. Each module is represented by a
single octet. If the value of a single octet is the ascii representation
of the character '1', it indicates that the module represented
by that octet is present, if '0', the module is absent.
The number of octets in the string is given by hmSysGroupCapacity.
If the value of this variable changes, a hmGroupMapChange trap
is sent.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.248.14.1.1.4 |
hmSysMaxPowerSupplyMaximum number of power supplies for this chassis. Within
each managed chassis/switch, the groups are uniquely numbered
in the range from 1 to hmSysMaxPowerSupply.ro Integer32 .1.3.6.1.4.1.248.14.1.1.5 |
hmSysMaxFanMaximum number of fans for this chassis. Within each managed
chassis/switch, the fans are uniquely numbered in the range
from 0 to hmSysMaxFan.ro Integer32 .1.3.6.1.4.1.248.14.1.1.6 |
hmSysGroupModuleCapacityMaximum number of modules that an individual group can
contain in this system.ro Integer32 .1.3.6.1.4.1.248.14.1.1.7 |
hmSysModulePortCapacityMaximum number of ports that an individual module can
contain in this system.ro Integer32 .1.3.6.1.4.1.248.14.1.1.8 |
hmSysGroupTableThis table contains variables for a closer description of
a group. SEQUENCE OF HmSysGroupEntry .1.3.6.1.4.1.248.14.1.1.9 |
hmSysGroupEntryThe entry of the hmSysGroupTable. HmSysGroupEntry .1.3.6.1.4.1.248.14.1.1.9.1 |
hmSysGroupIDindex to identify an interface card. This value is never
greater than hmSysGroupCapacity.ro Integer32 .1.3.6.1.4.1.248.14.1.1.9.1.1 |
hmSysGroupTypeType of interface card.ro Enumeration .1.3.6.1.4.1.248.14.1.1.9.1.2 |
hmSysGroupDescriptionDescription of interface card.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.248.14.1.1.9.1.3 |
hmSysGroupHwVersionHardware version of interface card.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.248.14.1.1.9.1.4 |
hmSysGroupSwVersionSoftware version of interface card.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.248.14.1.1.9.1.5 |
hmSysGroupModuleMapThis string represents the current configuration of a group,
encoded as an octet string. Each module is represented by a
single octet. If the value of a single octet is the ascii representation
of the character '1', it indicates that the module represented
by that octet is present, if '0', the module is absent. If the character is
'C', then the card is configurable but absent. The ports can be configured
and by setting hmSysModStatus to remove(3) the card can be logically
removed. The number of bytes in the string is given by
hmSysGroupModuleCapacity.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.248.14.1.1.9.1.6 |
hmSysGroupActionThis object, when read, always returns a value of other(1).
A value of reset(2) has the same effect as a power-on sequence
(coldstart). When set to resetStats(3), a reset of all statistic
counters of the card's ports will be forced. Any other value
results in a badValue status code.rw Enumeration .1.3.6.1.4.1.248.14.1.1.9.1.7 |
hmSysGroupActionResultResult of the last activated action. A value of zero
indicates that the result is ok. Bits set in the result
indicate error conditions.ro Integer32 .1.3.6.1.4.1.248.14.1.1.9.1.8 |
hmSysGroupIsolateModeSetting this variable to enable(1) separates the group from
the rest of the chassis, so that it will act like a
standalone-switch.rw Enumeration .1.3.6.1.4.1.248.14.1.1.9.1.9 |
hmSysGroupSerialNumThe serial number provided by vendor (ASCII).ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.248.14.1.1.9.1.10 |
hmSysGroupActionDelayPresetTime in seconds until a reset(2) or
hotRestart(10) that was triggered over
the hmSysGroupAction object is executed. Writing
a zero will cancel any scheduled reset.rw Integer32 .1.3.6.1.4.1.248.14.1.1.9.1.11 |
hmSysGroupActionDelayCurrentIf a delayed reset is scheduled this object
will incrementing from the start value to zero.ro Integer32 .1.3.6.1.4.1.248.14.1.1.9.1.12 |
hmSysModuleTableThis table contains variables for a closer description of a
module. SEQUENCE OF HmSysModuleEntry .1.3.6.1.4.1.248.14.1.1.10 |
hmSysModuleEntryThe entry of the hmSysModuleTable. HmSysModuleEntry .1.3.6.1.4.1.248.14.1.1.10.1 |
hmSysModGroupIDindex to identify an interface card. This value is never
greater than hmSysGroupCapacity.ro Integer32 .1.3.6.1.4.1.248.14.1.1.10.1.1 |
hmSysModIDindex to identify a module on an interface card. This value
is never greater than hmSysGroupModuleCapacity.ro Integer32 .1.3.6.1.4.1.248.14.1.1.10.1.2 |
hmSysModTypeType of a module.ro Enumeration .1.3.6.1.4.1.248.14.1.1.10.1.3 |
hmSysModDescriptionDescription of the module.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.248.14.1.1.10.1.4 |
hmSysModVersionversion of the module.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.248.14.1.1.10.1.5 |
hmSysModNumOfPortsThe numberOfPorts is the number of ports contained within
the module. Within each module, the ports are uniquely
numbered in the range from 1 to numberOfPorts.ro Integer32 .1.3.6.1.4.1.248.14.1.1.10.1.6 |
hmSysModFirstMauIndexvalue of the first mauIndex used by the module.ro Integer32 .1.3.6.1.4.1.248.14.1.1.10.1.7 |
hmSysModStatusstatus of hot-pluggable modules, only for PowerMICE.
If the value is physical(1), then the module is plugged in,
if the value is configurable, the ports can be configured,
but the card is absent, with the value remove(3) written to
the agent the card can be logically removed.rw Enumeration .1.3.6.1.4.1.248.14.1.1.10.1.8 |
hmSysModSerialNumThe serial number provided by vendor (ASCII).ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.248.14.1.1.10.1.9 |
hmInterfaceTableThis table contains variables for each interface of
the switch. SEQUENCE OF HmInterfaceEntry .1.3.6.1.4.1.248.14.1.1.11 |
hmInterfaceEntryThe entry of the hmInterfaceTable. HmInterfaceEntry .1.3.6.1.4.1.248.14.1.1.11.1 |
hmIfaceGroupIDindex to identify an interface card. This value is never
greater than hmSysGroupCapacity.ro Integer32 .1.3.6.1.4.1.248.14.1.1.11.1.1 |
hmIfaceIDindex to identify an interface within an interface card.ro Integer32 .1.3.6.1.4.1.248.14.1.1.11.1.2 |
hmIfaceStpEnableEnable or disable spanning tree protocol.rw Enumeration .1.3.6.1.4.1.248.14.1.1.11.1.3 |
hmIfaceLinkTypeDescribes the link type of the interface.rw Enumeration .1.3.6.1.4.1.248.14.1.1.11.1.4 |
hmIfaceActionThis object, when read, always returns a value of noAction(1).
When set to resetStats(2), a reset of all statistic counters
within this interfacecard will be forced.rw Enumeration .1.3.6.1.4.1.248.14.1.1.11.1.5 |
hmIfaceNextHopMacAddressThe macaddress of the next switch agent reachable via this
interface. If the value is 0:0:0:0:0:0, no other switch is
seen via this interface.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.248.14.1.1.11.1.6 |
hmIfaceFlowControlEnables or disables flow control per portrw Enumeration .1.3.6.1.4.1.248.14.1.1.11.1.7 |
hmIfacePriorityThresholdThis object is used to support the dot1dTrafficClassTable.
It defines the thresholds of the available priority-classes.
Starting at MACH Release 2.20 this variable is not used any more.rw Integer32 .1.3.6.1.4.1.248.14.1.1.11.1.8 |
hmIfaceNameUser configurable textual description of the interface. On devices
which support Power over Ethernet (IEEE 802.af), this object is
mapped to pethPsePortType of the RFC3621 MIB.rw DisplayString .1.3.6.1.4.1.248.14.1.1.11.1.9 |
hmIfaceTrunkIDIf the value of this variable is greater 0 then it belongs
to the link aggregation instance with the same index. If
the value is 0 no link aggregation uses this interface.rw Integer32 .1.3.6.1.4.1.248.14.1.1.11.1.10 |
hmIfacePrioTOSEnableEnable or disable Priority setting from IP TOS field.rw Enumeration .1.3.6.1.4.1.248.14.1.1.11.1.11 |
hmIfaceBcastLimitBroadcast rate: maximum number of broadcasts to be sent
on this port within one second, use 0 for no limitation.rw Integer32 .1.3.6.1.4.1.248.14.1.1.11.1.12 |
hmIfaceUtilizationThe best estimate of the mean physical layer
network utilization on this interface during the
last sampling interval, in hundredths of a percent.
The first historyControlInterval (rfc1757) of this
interface is used as sampling interval.ro Integer32 .1.3.6.1.4.1.248.14.1.1.11.1.13 |
hmIfaceUtilizationControlIntervalThe interval in seconds over which the data is
sampled for hmIfaceUtilization.
This interval can be any number of seconds
between 1 and 3600 (1 hour).
The first historyControlInterval (rfc1757) of this
interface is used as sampling interval.ro Integer32 .1.3.6.1.4.1.248.14.1.1.11.1.14 |
hmIfaceStpBpduGuardEnableEnabled or disabled the BPDU guard functionality per port.
If BPDU guard functionality are global enabled (hmSysStpBPDUGuardEnable=enable(1)),
and BPDU guard are enabled per port (hmIfaceStpBpduGuardEnable=enable(1)) and (R)STP are globally enabled
and an BPDU are received on the port, then hmIfaceStpBpduGuardStatus is set to true(1) for this port and
IfAdminStatus for this port is set to down(2).
Variable hmIfaceStpBpduGuardStatus can be reset to their original value (=false) with switching BPDU guard
functionality globally off.
IfAdminStatus can be reset to to their original values up() only manually.rw Enumeration .1.3.6.1.4.1.248.14.1.1.11.1.15 |
hmIfaceStpBpduGuardStatusAdvertised the state of BPDU guard functionality for this port.
If BPDU guard functionality fot this port is disabled or guard
functionality is enabled, but no BPDUs are received on this port,
then hmIfaceStpBpduGuardStatus is set to false(2) for this port.
If BPDU is received on an port with enabled BPDU guard functionality for this port
(hmIfaceStpBpduGuardEnable=enable(1)) and globally (hmSysStpBPDUGuardEnable=enable(1))
then hmIfaceStpBpduGuardStatus is set to true(1) and additionally IfAdminStatus for
this port is set to down(2).
Variable hmIfaceStpBpduGuardStatus can be reset (to their original values (=false))
with switching BPDU guard functionality globally off.
IfAdminStatus can be again reset to to their original values up() only manually.ro Enumeration .1.3.6.1.4.1.248.14.1.1.11.1.16 |
hmIfaceCapabilityCapability of the interface coded as an integer value
with each bit representing a special capability.
Meaning of the bits:
Bit 0: cabletest capability
Bit 1: realtime capability according to IEEE 1588.ro Integer32 .1.3.6.1.4.1.248.14.1.1.11.1.17 |
hmIfaceIngressLimiterModeThe ingress limiter can work in different modes.
Mode all limits the complete ingress traffic.
Mode bc limits only the ingress broadcast traffic.
Mode bc_mc limits the ingress broadcast and multicast traffic.
Mode bc_mc_uuc limits the ingress broadcast, multicast and
unknown unicast traffic.
The limiter is hardware dependend.
Not all modes are available on every hardware.rw Enumeration .1.3.6.1.4.1.248.14.1.1.11.1.18 |
hmIfaceIngressLimiterCalculationModeThe ingress limiter can measure the traffic
on a bytes per second
or on a packets per second basis.
The limiter calculation mode is hardware dependend.
Not all modes are available on every hardware.rw Enumeration .1.3.6.1.4.1.248.14.1.1.11.1.19 |
hmIfaceIngressLimiterRateThe rate of the ingress limiter.
The value 0 disables the limiter.rw Integer32 .1.3.6.1.4.1.248.14.1.1.11.1.20 |
hmIfaceEgressLimiterModeThe egress limiter can work in different modes.
Mode all limits the complete egress traffic.
Mode bc limits only the egress broadcast traffic.
Mode bc_mc limits the egress broadcast and multicast traffic.
Mode bc_mc_uuc limits the egress broadcast, multicast and
unknown unicast traffic.
The limiter is hardware dependend.
Not all modes are available on every hardware.rw Enumeration .1.3.6.1.4.1.248.14.1.1.11.1.21 |
hmIfaceEgressLimiterCalculationModeThe egress limiter can measure the traffic
on a bytes per second
or on a packets per second basis.
The limiter calculation mode is hardware dependend.
Not all modes are available on every hardware.rw Enumeration .1.3.6.1.4.1.248.14.1.1.11.1.22 |
hmIfaceEgressLimiterRateThe rate of the egress limiter.
The value 0 disables the limiter.rw Integer32 .1.3.6.1.4.1.248.14.1.1.11.1.23 |
hmIfaceUtilizationAlarmUpperThresholdSurveys the interface utilization hmIfaceUtilization and
generates an alarm for this interfaces, if the given
limit is exceeded.
A value of 0 disables the alarm generation.rw Integer32 .1.3.6.1.4.1.248.14.1.1.11.1.24 |
hmIfaceUtilizationAlarmLowerThresholdSurveys the interface utilization hmInfaceUtilization and
removes the alarm condition for this interfaces, if
the utilization value is below the given limit.
A value of 0 disables the alarm removal.rw Integer32 .1.3.6.1.4.1.248.14.1.1.11.1.25 |
hmIfaceUtilizationAlarmConditionThe alarm condition is given (true), if the given
hmIfaceUtilizationAlarmUpperThreshold limit is exceeded
by the interface utilization. The alarm condition
will be removed, when the interface utilization falls
below the hmIfaceUtilizationAlarmLowerThreshold.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.248.14.1.1.11.1.26 |
hmIfaceCableCrossingThis variable configures the cable crossing
on twisted pair cables.
When set to 'enable', the port uses
the crossover mode.
When set to 'disable', the port does not use
the crossover mode.
'Unsupported' is shown, if a port does not
support cable crossing.
It is not possible to set 'unsupported' to
any type of port.rw Enumeration .1.3.6.1.4.1.248.14.1.1.11.1.27 |
hmIfacePhyFastLinkDetectionThis variable configures the PHY specific
fast link detection feature on this port.
'Unsupported' is shown, if a port does not
support this feature.
It is not possible to set 'unsupported' to
any type of port.rw Enumeration .1.3.6.1.4.1.248.14.1.1.11.1.28 |
hmTrunkTableThis table contains variables for each trunk of
the switch. SEQUENCE OF HmTrunkEntry .1.3.6.1.4.1.248.14.1.1.12 |
hmTrunkEntryThe entry of the hmTrunkTable. HmTrunkEntry .1.3.6.1.4.1.248.14.1.1.12.1 |
hmTrunkIDIndex to identify a link aggregation instancero Integer32 .1.3.6.1.4.1.248.14.1.1.12.1.1 |
hmTrunkInterfacesList of interfaces which are aggregated in the trunk.
each octet pair contains the slotID and interfaceID.
Interfaces are added or deleteted using the variable
hmIfaceTrunkID.ro OCTET STRING .1.3.6.1.4.1.248.14.1.1.12.1.2 |
hmTrunkNameTextual description of the trunkrw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.248.14.1.1.12.1.3 |
hmTrunkActionaction according to hmIfaceAction which is performed
for all interfaces in the trunkrw Enumeration .1.3.6.1.4.1.248.14.1.1.12.1.4 |
hmTrunkAdminStatusThe desired state of the trunk. if this variable
is set to down(2), all interfaces which are aggregated
in the trunk are switched off simultaneously. Reading
this variable returns up(1) if at least one interface
of the trunk is operational (up).rw Enumeration .1.3.6.1.4.1.248.14.1.1.12.1.5 |
hmTrunkOperStatusThe operational state of the trunk. Reading this
variable returns up(1) if at least one interface
of the trunk is operational (up).ro Enumeration .1.3.6.1.4.1.248.14.1.1.12.1.6 |
hmTrunkLastChangeTime since system boot when there was a change in either
the operational state of the trunk or the list of aggregated
interfaces.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.248.14.1.1.12.1.7 |
hmSFPTableThis table contains variables for each SFP. SEQUENCE OF HmSFPEntry .1.3.6.1.4.1.248.14.1.1.13 |
hmSFPEntryEntry for a detected SFP. HmSFPEntry .1.3.6.1.4.1.248.14.1.1.13.1 |
hmSfpGroupIDIndex to identify a module.
This value is never greater than hmSysGroupModuleCapacity. Integer32 .1.3.6.1.4.1.248.14.1.1.13.1.1 |
hmSfpIDIndex to identify an interface within a module.
This value is never greater than hmSysModulePortCapacity. Integer32 .1.3.6.1.4.1.248.14.1.1.13.1.2 |
hmSfpConnectorThe SFP's Connector Type.ro Enumeration .1.3.6.1.4.1.248.14.1.1.13.1.3 |
hmSfpTransceiverThe SFP's Transceiver type.ro Enumeration .1.3.6.1.4.1.248.14.1.1.13.1.4 |
hmSfpVendorOUIThe SFP's vendor IEEE company ID (OUI).ro OCTET STRING .1.3.6.1.4.1.248.14.1.1.13.1.5 |
hmSfpVendorNameThe SFP's vendor name (ASCII).ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.248.14.1.1.13.1.6 |
hmSfpPartNumberThe SFP's part description number (ASCII).ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.248.14.1.1.13.1.7 |
hmSfpPartRevThe SFP's part revision number (ASCII).ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.248.14.1.1.13.1.8 |
hmSfpSerialNumThe SFP's serial number provided by vendor (ASCII).ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.248.14.1.1.13.1.9 |
hmSfpDateCodeThe SFP's vendor manufacturing date code. Format is YY:MM:DD.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.248.14.1.1.13.1.10 |
hmSfpBitRateThe SFP's nominal bitrate in units of MBits/sec.
Contains -1 in case of a device read error.ro Integer32 .1.3.6.1.4.1.248.14.1.1.13.1.11 |
hmSfpTemperatureThis signed integer is used to identify
the temperature within the SFP in units of centigrade (celsius).
Contains -1000 in case of a device read error.ro Integer32 .1.3.6.1.4.1.248.14.1.1.13.1.12 |
hmSfpTxPowerThe SFP's internally measured Tx Power in units of milliWatts.
(ASCII representation of floating point number).ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.248.14.1.1.13.1.13 |
hmSfpRxPowerThe SFP's internally measured Rx Power in units of milliWatts.
(ASCII representation of floating point number).ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.248.14.1.1.13.1.14 |
hmSfpTxPowerIntThe SFP's internally measured Tx Power in units of 1/10 microWatts.ro Integer32 .1.3.6.1.4.1.248.14.1.1.13.1.15 |
hmSfpRxPowerIntThe SFP's internally measured Rx Power in units of 1/10 microWatts.ro Integer32 .1.3.6.1.4.1.248.14.1.1.13.1.16 |
hmSfpRxPowerStateThe state of the SFP's internally measured Rx.ro Enumeration .1.3.6.1.4.1.248.14.1.1.13.1.17 |
hmSfpInfoVersionVersion of SFP's Hirschmann Information.
Contains -1 in case of a device read error.ro Integer32 .1.3.6.1.4.1.248.14.1.1.13.1.20 |
hmSfpInfoPartNumberPart Number of SFP's Hirschmann Information.ro DisplayString .1.3.6.1.4.1.248.14.1.1.13.1.21 |
hmSfpInfoPartIdPart Identifier of SFP's Hirschmann Information.ro DisplayString .1.3.6.1.4.1.248.14.1.1.13.1.22 |
hmSfpInfoMagic1, if SFP contains vendor specific information by Hirschmann, otherwise 0.ro Integer32 .1.3.6.1.4.1.248.14.1.1.13.1.23 |
hmSfpSupportedIndicates if the local agent supports this SFP.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.248.14.1.1.13.1.24 |
hmSfpMaxLength-fiber-9Max. usable length for the cable type '9/125 micrometer fiber'
with this SFP in units of meters.ro Integer32 .1.3.6.1.4.1.248.14.1.1.13.1.30 |
hmSfpMaxLength-fiber-50Max. usable length for the cable type '50/125 micrometer fiber'
with this SFP in units of meters.ro Integer32 .1.3.6.1.4.1.248.14.1.1.13.1.31 |
hmSfpMaxLength-fiber-62-5Max. usable length for the cable type '62.5/125 micrometer fiber'
with this SFP in units of meters.ro Integer32 .1.3.6.1.4.1.248.14.1.1.13.1.32 |
hmSfpMaxLength-copperMax. usable length for the cable type 'copper'
with this SFP in units of meters.ro Integer32 .1.3.6.1.4.1.248.14.1.1.13.1.33 |
hmSfpTxPowerdBmThe SFP's internally measured Tx Power in units of dBm.
(ASCII representation of floating point number).ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.248.14.1.1.13.1.34 |
hmSfpRxPowerdBmThe SFP's internally measured Rx Power in units of dBm.
(ASCII representation of floating point number).ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.248.14.1.1.13.1.35 |
hmSysChassisNameThis displaystring represents the name of the Chassis.
Any change of this variable will cause an automatically
update of this value on each Basic Board in this Chassis.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.248.14.1.1.20 |
hmSysStpEnableThis variable controls the STP operation of the entire
switch. To control the STP function of each port use
hmIfaceStpEnablerw Enumeration .1.3.6.1.4.1.248.14.1.1.21 |
hmSysFlowControlenables or disables flow control for the switch unit.rw Enumeration .1.3.6.1.4.1.248.14.1.1.22 |
hmSysBOOTPEnableEnable/Disable BOOTP operation. A (1) enables, a (2) disables.
When disabled, no BOOTPs are transmitted by the system.
When enabled, the system sends BOOTP requests at booting.rw Enumeration .1.3.6.1.4.1.248.14.1.1.23 |
hmSysDHCPEnableEnable/Disable DHCP operation. A (1) enables, a (2) disables.
When disabled, no DHCPs are transmitted by the system.
When enabled, the system sends DHCP requests at booting.rw Enumeration .1.3.6.1.4.1.248.14.1.1.24 |
hmSysTelnetEnableEnable/Disable Telnet operation. A (1) enables, a (2) disables.
When disabled, no Telnet sessions are allowed by the system.rw Enumeration .1.3.6.1.4.1.248.14.1.1.25 |
hmSysHTTPEnableEnable/Disable HTTP connection. A (1) enables, a (2) disables.
When disabled, no HTTP is allowed by the system.rw Enumeration .1.3.6.1.4.1.248.14.1.1.26 |
hmSysPlugAndPlayEnable/Disable Plug&Play feature. A (1) enables, a (2) disables.
if this variable is set to enable(1), special Plug&Play actions are
performed at boot time and after a successful completion the value
is automatically reset to the disable(2) state.rw Enumeration .1.3.6.1.4.1.248.14.1.1.27 |
hmBcastLimiterModeGlobal configuration of feature broadcast limiter.
If enabled, for each port the maximum rate of broadcasts
can be specified.rw Enumeration .1.3.6.1.4.1.248.14.1.1.29 |
hmSystemTimeTime measured in seconds since 00:00:00 UTC, January 1, 1970.
The clock of the agents may be set using this variable.
Changing this variable on one agent automatically updates
the value on the other agents in the same chassis.rw TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.248.14.1.1.30 |
hmSystemTimeSourceShows the source of the system time.ro Enumeration .1.3.6.1.4.1.248.14.1.1.31 |
hmSysStpBPDUGuardEnableThis variable controls the BPDU Guard operation of the entire
switch (globally). To control the BPDU Guard function of each port use
hmIfaceStpBpduGuardEnable.
If BPDU guard functionality are global enabled (hmSysStpBPDUGuardEnable=enable(1)),
and BPDU guard are enabled per port (hmIfaceStpBpduGuardEnable=enable(1)) and (R)STP are globally enabled
and an BPDU are received on the port, then hmIfaceStpBpduGuardStatus is set to true(1) for this port and
IfAdminStatus is set to down(2) for this port.
Variable hmIfaceStpBpduGuardStatus can be reset (to their original values (=false)) with switching
BPDU guard functionality globally off (hmSysStpBPDUGuardEnable=disable(2)).
IfAdminStatus can be again reset to to their original values up() only manually.
The default value of hmSysStpBPDUGuardEnable is disable(2).rw Enumeration .1.3.6.1.4.1.248.14.1.1.32 |
hmSysSTPErrorNumberAdvertised the reason why (R)STP could not be switched on.
Error reasons are coded as OR operation bit by bit, see values:
0x00 - no errors - (R)STP is switched on,
0x01 - (R)STP cannot be switched on, because of standby mode,
0x02 - (R)STP cannot be switched on, because of kopp Local Active,
0x04 - (R)STP cannot be switched on, because of kopp Slave Active,
0x08 - (R)STP cannot be switched on, because of kopp Master Active,
0x10 - (R)STP cannot be switched on, because of sysRingOn and sysRMMode,
0x20 - (R)STP cannot be switched on, because of error if BB_SetParameter is occured.ro Integer32 .1.3.6.1.4.1.248.14.1.1.33 |
hmSysSoftwareCapabilityThis variable shows the capability of the running software.
The string is formated as follow:
Byte 1 : Always L (for Layer)
Byte 2 : 2 or 3 (dependend if the software supports onyl switching (2)
or also routing (3))
Byte 3 : E or P (Enhanced or Professional software functionality)ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.248.14.1.1.34 |
hmLEDGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.1.1.35 |
hmLEDRSGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.1.1.35.1 |
hmLEDRSPowerSupplyStatus from the PowerSupply LED.ro LEDState .1.3.6.1.4.1.248.14.1.1.35.1.1 |
hmLEDRStandbyStatus from the Standby LED.ro LEDState .1.3.6.1.4.1.248.14.1.1.35.1.2 |
hmLEDRSRedundancyManagerStatus from the RM LED.ro LEDState .1.3.6.1.4.1.248.14.1.1.35.1.3 |
hmLEDRSFaultStatus from the Fault LED.ro LEDState .1.3.6.1.4.1.248.14.1.1.35.1.4 |
hmLEDOctGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.1.1.35.2 |
hmLEDOctPowerSupply1Status from the PowerSupply 1 LED.ro LEDState .1.3.6.1.4.1.248.14.1.1.35.2.1 |
hmLEDOctPowerSupply2Status from the PowerSupply 2 LED.ro LEDState .1.3.6.1.4.1.248.14.1.1.35.2.2 |
hmLEDOctRedundancyManagerStatus from the RM LED.ro LEDState .1.3.6.1.4.1.248.14.1.1.35.2.3 |
hmLEDOctFaultStatus from the Fault LED.ro LEDState .1.3.6.1.4.1.248.14.1.1.35.2.4 |
hmLEDRSRGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.1.1.35.3 |
hmLEDRSRPowerSupplyStatus from the PowerSupply LED.ro LEDState .1.3.6.1.4.1.248.14.1.1.35.3.1 |
hmLEDRSRStandbyStatus from the Standby LED.ro LEDState .1.3.6.1.4.1.248.14.1.1.35.3.2 |
hmLEDRSRRedundancyManagerStatus from the RM LED.ro LEDState .1.3.6.1.4.1.248.14.1.1.35.3.3 |
hmLEDRSRFaultStatus from the Fault LED.ro LEDState .1.3.6.1.4.1.248.14.1.1.35.3.4 |
hmLEDRSRRelay1Status from the Relay1 LED.ro LEDState .1.3.6.1.4.1.248.14.1.1.35.3.5 |
hmLEDRSRRelay2Status from the Relay2 LED.ro LEDState .1.3.6.1.4.1.248.14.1.1.35.3.6 |
hmDIPSwitchGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.1.1.36 |
hmDIPSwitchRSGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.1.1.36.1 |
hmDIPSwitchRSRedundancyManagerStatus from redundancy manager DIP switch.ro DIPSwitchState .1.3.6.1.4.1.248.14.1.1.36.1.1 |
hmDIPSwitchRSStandbyStatus from Standby DIP switch.ro DIPSwitchState .1.3.6.1.4.1.248.14.1.1.36.1.2 |
hmDIPSwitchMICEGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.1.1.36.2 |
hmDIPSwitchMICERedundancyManagerStatus from redundancy manager DIP switch.ro DIPSwitchState .1.3.6.1.4.1.248.14.1.1.36.2.1 |
hmDIPSwitchMICERingPortStatus from ring ports DIP switch.
on (1) indicates port 1 on module 1 and port 1 on module 2 are used as ring ports.
off (2) indicates port 1 and 2 on module 1 are used as ring ports.ro DIPSwitchState .1.3.6.1.4.1.248.14.1.1.36.2.2 |
hmDIPSwitchMICEStandbyStatus from Standby DIP switch.ro DIPSwitchState .1.3.6.1.4.1.248.14.1.1.36.2.3 |
hmDIPSwitchMICEConfigStatus from DIP switch configuration.
on (1) indicates DIP switch configuration is enabled.
off (2) indicates DIP switch configuration is disabled.ro DIPSwitchState .1.3.6.1.4.1.248.14.1.1.36.2.4 |
hmSysMaxTrunksMaximum number of trunks for this chassis.ro Integer32 .1.3.6.1.4.1.248.14.1.1.37 |
hmLimiterGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.1.1.38 |
hmIngressLimiterGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.1.1.38.1 |
hmIngressLimiterEnableThe global ingress limiter can be enabled or disabled.rw Enumeration .1.3.6.1.4.1.248.14.1.1.38.1.1 |
hmIngressLimiterModeThe global ingress limiter can work in different modes.
Mode all limits the complete ingress traffic.
Mode bc limits only the ingress broadcast traffic.
Mode bc_mc limits the ingress broadcast and multicast traffic.
Mode bc_mc_uuc limits the ingress broadcast, multicast and
unknown unicast traffic.
The limiter is hardware dependend.
Not all modes are available on every hardware.rw Enumeration .1.3.6.1.4.1.248.14.1.1.38.1.2 |
hmIngressUnknUcLimiterGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.1.1.38.1.3 |
hmIngressUnknUcLimiterModeThe global unknown unicast ingress limiter can be enabled or disabled.
The limiter is hardware dependend.rw Enumeration .1.3.6.1.4.1.248.14.1.1.38.1.3.1 |
hmIngressUnknUcLimiterCalculationModeThe global unknown unicast ingress limiter
can measure the traffic on a bytes per second
or on a packets per second basis.
The limiter calculation mode is hardware dependend.
Not all modes are available on every hardware.rw Enumeration .1.3.6.1.4.1.248.14.1.1.38.1.3.2 |
hmIngressUnknUcLimiterRateThe rate of the global unknown unicast ingress limiter.
The value 0 disables the limiter.rw Integer32 .1.3.6.1.4.1.248.14.1.1.38.1.3.3 |
hmEgressLimiterGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.1.1.38.2 |
hmEgressLimiterEnableThe global egress limiter can be enabled or disabled.rw Enumeration .1.3.6.1.4.1.248.14.1.1.38.2.1 |
hmSysUSBGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.1.1.39 |
hmSysMaxUSBPortsMaximum number of USB ports in this chassis.ro Integer32 .1.3.6.1.4.1.248.14.1.1.39.1 |
hmSysSwitchGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.1.1.40 |
hmSysSwitchLearningControls address learning by the switch.
When disabled the address database of the switch will
not be updated with dynamic filtering entries.
Static Filtering Entries and Group Registration Entries
are not affected.rw Enumeration .1.3.6.1.4.1.248.14.1.1.40.1 |
hmSysSwitchMRUThe Maximum Receive Unit MRU that
can be received by the switch.rw Enumeration .1.3.6.1.4.1.248.14.1.1.40.2 |
hmSysSwitchFastLinkDetectionControls if the fast link detection is enabled or not.rw Enumeration .1.3.6.1.4.1.248.14.1.1.40.3 |
hmSysSwitchAddressRelearnDetectionControls if detection of address relearns
is enabled or not.rw Enumeration .1.3.6.1.4.1.248.14.1.1.40.4 |
hmSysSwitchAddressRelearnThresholdThe value of relearnd addresses to signal address
relearn threshold exceeded.rw Integer32 .1.3.6.1.4.1.248.14.1.1.40.5 |
hmSysSwitchDuplexMismatchDetectionControls if duplex mismatch detection
is enabled or not.rw Enumeration .1.3.6.1.4.1.248.14.1.1.40.6 |
hmSysSwitchFDBFullCounterThe number of FDB Full indications that the agent has detected since reboot.ro Counter32 .1.3.6.1.4.1.248.14.1.1.40.7 |
hmSysSwitchFDBHashOptimizingModeMode to optimize the MAC address table hashing algorithm.
Which modes can be configured is hardware dependend.
After configuration a reboot is needed.rw Integer32 .1.3.6.1.4.1.248.14.1.1.40.8 |
hmSysSwitchFDBHashOptimizingStatusShows the current hash mode of this device.ro Integer32 .1.3.6.1.4.1.248.14.1.1.40.9 |
hmSysSwitchVLANGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.1.1.40.10 |
hmSysSwitchVLANLearningModeControls the VLAN learning mode by the switch.
When set to IVL Independend VLAN Learning is active.
When set to SVL Shared VLAN Learning is active.
After setting this variable the switch have to be restarted.rw Enumeration .1.3.6.1.4.1.248.14.1.1.40.10.1 |
hmSysSwitchVLANLearningStatusShows the current VLAN learning mode.
When set to IVL Independend VLAN Learning is active.
When set to SVL Shared VLAN Learning is active.ro Enumeration .1.3.6.1.4.1.248.14.1.1.40.10.2 |
hmSysSwitchServiceModeGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.1.1.40.11 |
hmSysSwitchServiceModeEnables the service mode.
If enabled, the switch can be separated into two switching areas
with the redundant power supply.
The two HIPER Ring ports are in area one.
The other ports are in area two.
Area one is VLAN capable, area two is not VLAN capable.rw Enumeration .1.3.6.1.4.1.248.14.1.1.40.11.1 |
hmSysSwitchServiceVlanDefined the Vlan for the service mode.
The Vlan must be a valid Vlan and neither Vlan 0 (mgmt vlan)
nor Vlan 1 (Default Vlan).rw Integer32 .1.3.6.1.4.1.248.14.1.1.40.11.2 |
hmSysSwitchServiceModeOperStateIf enabled, the switch has been separated into two switching areas
with the redundant power supply.
The two HIPER Ring ports are in area one.
The other ports are in area two.
Area one is VLAN capable, area two is not VLAN capable.ro Enumeration .1.3.6.1.4.1.248.14.1.1.40.11.3 |
hmSysSwitchRedundancyGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.1.1.40.20 |
hmSysSwitchRedundancyRstpMrpModeRstp Mrp is enabled if this object is set to enable(1).
Rstp Mrp is disabled if this object is set to disable(2).rw Enumeration .1.3.6.1.4.1.248.14.1.1.40.20.1 |
hmSysSwitchRedundancyRstpMrpConfigErrorThis object indicates a Rstp Mrp fail configuration if the value
true is shown.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.248.14.1.1.40.20.2 |
hmSysSwitchRedundancyRstpMrpConfigErrorBridgeThe identifier of the device which has a Rstp Mrp fail
configuration or Null if there is no fail configuration.ro BridgeIdOrNull .1.3.6.1.4.1.248.14.1.1.40.20.3 |
hmSysSelftestGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.1.1.41 |
hmSysSelftestRAMControls RAM selftest on coldstart of the device.
When disabled the device booting time is reduced.rw Enumeration .1.3.6.1.4.1.248.14.1.1.41.1 |
hmSysSelftestRebootOnErrorIf enabled the software does make a reboot if there is a
serious error detected.rw Enumeration .1.3.6.1.4.1.248.14.1.1.41.2 |
hmSysSelftestMMUStatusStatus of the memory managment unit.ro Enumeration .1.3.6.1.4.1.248.14.1.1.41.3 |
hmSysSelftestRebootOnHdxErrorIf enabled the software does a reboot if there is a
Half duplex mismatch error is detected. The option depends on hmSysSelftestRebootOnError.rw Enumeration .1.3.6.1.4.1.248.14.1.1.41.4 |
hmSysOEMGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.1.1.42 |
hmSysOEMIDUnique OEM ID.ro Integer32 .1.3.6.1.4.1.248.14.1.1.42.1 |
hmSysMaxSignalContactsMaximum number of signal contacts for this chassis. Within
each managed chassis/switch, the groups are uniquely numbered
in the range from 1 to hmSysMaxSignalContacts.ro Integer32 .1.3.6.1.4.1.248.14.1.1.43 |
hmSysHttpsEnableEnables/Disables HTTPS access to the device. A (1) enables, a (2) disables.rw Enumeration .1.3.6.1.4.1.248.14.1.1.44 |
hmSysHttpsPortNumberThe port number of the HTTPS web server.rw INTEGER .1.3.6.1.4.1.248.14.1.1.45 |
hmSysSkipAcaOnBootEnable/disable loading from ACA on startup.rw Enumeration .1.3.6.1.4.1.248.14.1.1.46 |
hmPSTableThis table contains all variables related to the power supply
units of the chassis/switch. For each power supply slot exists
one instance. SEQUENCE OF HmPSEntry .1.3.6.1.4.1.248.14.1.2 |
hmPSEntryThe entry of the hmPSTable. HmPSEntry .1.3.6.1.4.1.248.14.1.2.1 |
hmPSSysIDThe value of SysID is assigned so as to uniquely identify a
chassis/switch among the subordinate managed objects of the
system.ro Integer32 .1.3.6.1.4.1.248.14.1.2.1.1 |
hmPSIDThis Index is used to identify the associated power supply
unit.ro Integer32 .1.3.6.1.4.1.248.14.1.2.1.2 |
hmPSStateIndicates the operational state of the associated power
supply. If the value of this variable changes, a hmPowerSupply
trap is sent.ro Enumeration .1.3.6.1.4.1.248.14.1.2.1.3 |
hmPSTypeType of the associated power supply.ro Enumeration .1.3.6.1.4.1.248.14.1.2.1.4 |
hmPSVersionVersion of the associated power supply.ro Integer32 .1.3.6.1.4.1.248.14.1.2.1.5 |
hmPSDescriptionDescription of the associated power supply.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.248.14.1.2.1.6 |
hmPSSerialNumberSerial number of the associated power supply.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.248.14.1.2.1.7 |
hmPSProductCodeProduct code of the associated power supply.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.248.14.1.2.1.8 |
hmPSPowerBudgetPower budget of the associated power supply.ro Integer32 .1.3.6.1.4.1.248.14.1.2.1.9 |
hmFanTableThis table contains all variables related to the fan units
of the chassis/switch. For each fan slot exists one instance. SEQUENCE OF HmFanEntry .1.3.6.1.4.1.248.14.1.3 |
hmFanEntryThe entry of the hmFanTable. HmFanEntry .1.3.6.1.4.1.248.14.1.3.1 |
hmFanSysIDThe value of SysID is assigned so as to uniquely identify a
chassis among the subordinate managed objects of the system.ro Integer32 .1.3.6.1.4.1.248.14.1.3.1.1 |
hmFanIDThis Index is used to identify the associated fan.ro Integer32 .1.3.6.1.4.1.248.14.1.3.1.2 |
hmFanStateIndicates the operational state of the associated fan.ro Enumeration .1.3.6.1.4.1.248.14.1.3.1.3 |
hmFwdPriorityConfiguration OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.1.4 |
hmPrioTOSEnableGlobal configuration of feature IP-TOS priority to
802.1D-1998 priority. If enabled, the priority of the
TOS field is mapped to 802.1D priorityrw Enumeration .1.3.6.1.4.1.248.14.1.4.1 |
hmPrioMACAddressEnableGlobal configuration of feature priority by MAC address.
If enabled, for each static MAC address a priority
could be specifiedrw Enumeration .1.3.6.1.4.1.248.14.1.4.2 |
hmPrioVlan0TagTransparentModeenables or disables the transparent mode for
priority tagged frames (frames with VLAN-ID 0)
for the switch unit.rw Enumeration .1.3.6.1.4.1.248.14.1.4.3 |
hmPrioMACAddressTableTable for assigning priority to MAC addresses SEQUENCE OF HmPrioMACAddressEntry .1.3.6.1.4.1.248.14.1.4.10 |
hmPrioMACAddressEntryThe entry of the hmPrioMACAddressTable. HmPrioMACAddressEntry .1.3.6.1.4.1.248.14.1.4.10.1 |
hmPrioMACAddresssame as dot1dStaticAddressro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.248.14.1.4.10.1.1 |
hmPrioMACReceivePortto be compatible with dot1dStaticTablero Integer32 .1.3.6.1.4.1.248.14.1.4.10.1.2 |
hmPrioMACPrioritypriority value for the frame with the specific
destination MAC address.
0..7: priority
8 : disabled (no priority by MAC address)
9 : discard the framerw Integer32 .1.3.6.1.4.1.248.14.1.4.10.1.3 |
hmPrioMACStatusstatus flag according to dot1dStaticStatusrw Enumeration .1.3.6.1.4.1.248.14.1.4.10.1.4 |
hmPrioTrafficClassTableTranslation table for traffic classes to 802.1D-1998 priority SEQUENCE OF HmPrioTrafficClassEntry .1.3.6.1.4.1.248.14.1.4.11 |
hmPrioTrafficClassEntryThe entry of the hmPrioTrafficClassTable. HmPrioTrafficClassEntry .1.3.6.1.4.1.248.14.1.4.11.1 |
hmPrioTrafficClassIDThis index is used to identify the associated traffic classro Integer32 .1.3.6.1.4.1.248.14.1.4.11.1.1 |
hmPrioTrafficClassWeightWith this parameter the queue mode of each
traffic class can be set.
2..99: weight for WFQ (Weighted-Fair-Queuing)
100: strict priorityrw Integer32 .1.3.6.1.4.1.248.14.1.4.11.1.2 |
hmPrioTosToPrioTableTranslation table IP-TOS priority to 802.1D-1998 priority SEQUENCE OF HmPrioTosToPrioEntry .1.3.6.1.4.1.248.14.1.4.12 |
hmPrioTosToPrioEntryThe entry of the hmPrioTosToPrioEntry. HmPrioTosToPrioEntry .1.3.6.1.4.1.248.14.1.4.12.1 |
hmPrioTTPTosThis index is used to identify the associated TOS valuero Integer32 .1.3.6.1.4.1.248.14.1.4.12.1.1 |
hmPrioTTPPrioThis index is used to identify the associated 802.1D priorityro Integer32 .1.3.6.1.4.1.248.14.1.4.12.1.2 |
hmCurrentAddressTableA table containing filtering information
configured into the bridge by (local or network)
management or dynamic by GMRP or IGMP Snooping
specifying the set of ports to which
frames received from specific ports and containing
specific destination addresses are allowed to be
forwarded. The value of zero in this table as the
port number from which frames with a specific
destination address are received, is used to
specify all ports for which there is no specific
entry in this table for that particular
destination address. Entries are valid for
unicast and for group/broadcast addresses. SEQUENCE OF HmCurrentAddressEntry .1.3.6.1.4.1.248.14.1.5 |
hmCurrentAddressEntryFiltering information configured into the bridge
by (local or network) management specifying the
set of ports to which frames received from a
specific port and containing a specific
destination address are allowed to be forwarded. HmCurrentAddressEntry .1.3.6.1.4.1.248.14.1.5.1 |
hmCurrentAddressThe destination MAC address in a frame to which
this entry's filtering information applies. This
object can take the value of a unicast address, a
group address or the broadcast address.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.248.14.1.5.1.1 |
hmCurrentAddressReceivePortEither the value '0', or the port number of the
port from which a frame must be received in order
for this entry's filtering information to apply.
A value of zero indicates that this entry applies
on all ports of the bridge for which there is no
other applicable entry.ro Integer32 .1.3.6.1.4.1.248.14.1.5.1.2 |
hmCurrentAddressStaticEgressPortsThe set of ports to which frames received from a
specific port and destined for a specific MAC
address, are allowed to be forwarded. Each octet
within the value of this object specifies a set of
eight ports, with the first octet specifying ports
1 through 8, the second octet specifying ports 9
through 16, etc. Within each octet, the most
significant bit represents the lowest numbered
port, and the least significant bit represents the
highest numbered port. Thus, each port of the
bridge is represented by a single bit within the
value of this object. If that bit has a value of
'1' then that port is included in the set of
ports; the port is not included if its bit has a
value of '0'. (Note that the setting of the bit
corresponding to the port from which a frame is
received is irrelevant.) The default value of
this object is a string of ones of appropriate
length.ro OCTET STRING .1.3.6.1.4.1.248.14.1.5.1.3 |
hmCurrentAddressEgressPortsThe complete set of ports, to which frames destined
for this Group MAC Address are currently being forwarded.
This includes Group MAC Addresses which were set statically
or which were learnt by GMRP or some other dynamic mechanism.
Each octet within the value of this object specifies
a set of eight ports, with the first octet specifying
ports 1 through 8, the second octet specifying ports 9
through 16, etc. Within each octet, the most
significant bit represents the lowest numbered
port, and the least significant bit represents the
highest numbered port. Thus, each port of the
bridge is represented by a single bit within the
value of this object. If that bit has a value of
'1' then that port is included in the set of
ports; the port is not included if its bit has a
value of '0'. (Note that the setting of the bit
corresponding to the port from which a frame is
received is irrelevant.) The default value of
this object is a string of ones of appropriate
length.ro OCTET STRING .1.3.6.1.4.1.248.14.1.5.1.4 |
hmCurrentAddressStatusThis object indicates the status of this entry.
The default value is permanent(3).
other(1) - this entry is currently in use but
the conditions under which it will
remain so are different from each of the
following values.
invalid(2) - writing this value to the object
removes the corresponding entry.
permanent(3) - this entry is currently in use
and will remain so after the next reset
of the bridge.
deleteOnReset(4) - this entry is currently in
use and will remain so until the next
reset of the bridge.
deleteOnTimeout(5) - this entry is currently
in use and will remain so until it is
aged out.ro Enumeration .1.3.6.1.4.1.248.14.1.5.1.5 |
hmRS2ext OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.1.10 |
hmRS2OperModehmRS2OperMode shows the operational mode of the system:
normal: normal mode,
standby-active: standby mode, but switch is active, because
the master switch is e.g. not reachable,
standby-inactive: stand by mode,
redundancy-manager-active: redundancy mode and redundancy-manager has
closed RS2 ring,
redundancy-manager-inactive: redundancy mode and redundancy-manager has
opened RS2 ring.
If the value changes, a trap is sent.ro Enumeration .1.3.6.1.4.1.248.14.1.10.1 |
hmRS2ConfigErrorRS2hmConfigError indicates a configuration error of the
system:
no error: no configuration error,
error: in normal mode hmConfigError indicates failure of
control line or connection of 2 RS2 in normal mode,
in stand by mode hmConfigError indicates absence of
control line, failure of control line or connection
of 2 RS2 in stand by mode.ro Enumeration .1.3.6.1.4.1.248.14.1.10.2 |
hmRS2SigRelayStatehmRS2SigRelayState shows the state of the (non potential)
signalling relay in standard mode:
off: ok,
on: powersupply not ok or linkstate of a port not ok or
configuration error, see power supply table or
ifMauTable (attribute ifMauMediaAvailable) or
hmConfigError for details.ro Enumeration .1.3.6.1.4.1.248.14.1.10.3 |
hmSigLinkTableThis table contains all variables to mask an alarm for the
signalling relay, produced by a link. The index for a link
corresponds with ifMauIfIndex. SEQUENCE OF HmSigLinkEntry .1.3.6.1.4.1.248.14.1.10.4 |
hmSigLinkEntryThe entry of the hmSigLinkTable. HmSigLinkEntry .1.3.6.1.4.1.248.14.1.10.4.1 |
hmSigLinkIDThis index is used to identify the associated link and
corresponds with ifMauIfIndex.ro Integer32 .1.3.6.1.4.1.248.14.1.10.4.1.1 |
hmSigLinkAlarmIndicates whether an alarm for the signalling relay of the
associated link will be produced or not, so you can mask the
value of ifMauMediaAvailable.rw Enumeration .1.3.6.1.4.1.248.14.1.10.4.1.2 |
hmSigTrapReasonThis object identifies the reason for a trap. There are
three reasons for a trap:
hmRS2ConfigError
ifMauMediaAvailable
hmPSState
The entity which produces the trap, is specified by
hmSigReasonIndex.ro OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.1.10.5 |
hmSigReasonIndexThis attribute specifies the entity which produces the trap.
1 - n: index of powersupply table / interfaces table
0: config-error.ro Integer32 .1.3.6.1.4.1.248.14.1.10.6 |
hmRS2TopologyGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.1.10.7 |
hmRS2PartnerIpAddressThis variable can be used to set manually the
redundancy partner of the RS2 agent.rw IpAddress .1.3.6.1.4.1.248.14.1.10.7.1 |
hmRS2TopologyTableThis table describes the topology of rs2-rings. SEQUENCE OF HmRS2TopologyEntry .1.3.6.1.4.1.248.14.1.10.7.2 |
hmRS2TopologyEntryThe entry of the hmRS2TopologyTable. HmRS2TopologyEntry .1.3.6.1.4.1.248.14.1.10.7.2.1 |
hmRS2TopologyLinkIDThis index is used to identify the associated link and
corresponds with ifMauIfIndex.ro Integer32 .1.3.6.1.4.1.248.14.1.10.7.2.1.1 |
hmRS2TopologyIpAddressThis variable can be used to set manually the next RS2 agent.rw IpAddress .1.3.6.1.4.1.248.14.1.10.7.2.1.2 |
hmRS2ConnectionMirroringGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.1.10.8 |
hmRS2ConnectionMirroringStatusSet this variable to configure the status of the
connection mirroring functionality.
The definition of a destination port is not required.rw Enumeration .1.3.6.1.4.1.248.14.1.10.8.1 |
hmRS2ConnectionMirroringPortOneSet this variable to the first port to be mirrored.rw Integer32 .1.3.6.1.4.1.248.14.1.10.8.2 |
hmRS2ConnectionMirroringPortTwoSet this variable to the second port to be mirrored.rw Integer32 .1.3.6.1.4.1.248.14.1.10.8.3 |
hmRS2DisableLearningGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.1.10.9 |
hmRS2DisableLearningStatusWhen set to active the Learning Process is disabled,
no new Dynamic Filtering Entries are created and
exsisting Dynamic Filtering Entries are removed from
the Filtering Database.
Static Filtering Entries and Group Registration Entries
are not affected.rw Enumeration .1.3.6.1.4.1.248.14.1.10.9.1 |
hmRS2SigRelayGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.1.10.10 |
hmRS2SigRelayModeWhen set to standard, this is the default,
the signalling relay shows the state of
hmRS2SigRelayState.
When set to manual, the relay is controlled
by hmRS2SigRelayManualState.rw Enumeration .1.3.6.1.4.1.248.14.1.10.10.1 |
hmRS2SigRelayManualStateWhen set to on, this is the default,
the signalling relay is opened.
When set to off the relay is closed.rw Enumeration .1.3.6.1.4.1.248.14.1.10.10.2 |
hmRS2VlanGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.1.10.11 |
hmRS2VlanModeEnables/disables the VLAN mode on this device.
When enabled the switch will operate in 802.1Q mode,
else in 802.1d mode.
After setting this variable the switch have to be reset.
The default value is disable.rw Enumeration .1.3.6.1.4.1.248.14.1.10.11.1 |
hmRS2VlanStatusShows the current VLAN mode of this device.
When enabled the switch operates in 802.1Q mode,
else in 802.1d mode.ro Enumeration .1.3.6.1.4.1.248.14.1.10.11.2 |
hmRS2SelftestGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.1.10.12 |
hmRS2SelftestResultResult of the selftest coded as an integer value
with each bit representing the result of a different
sub part test. Bits set in the result indicate error
conditions of the sub part tests.
Meaning of the bits:
Bit 0: error switch memoryro Integer32 .1.3.6.1.4.1.248.14.1.10.12.1 |
hmRS2SelftestModeMode of the selftest coded as an integer value
with each bit representing a special behaviour
of the tests.
Meaning of the bits:
Bit 0: reboot on failure
Bit 1: show failure with hmRS2SigRelayState
(a trap will be send also)
Bit 2: do switch memory test on start up
Bit 3: Clear Bit 2 after next reboot if test has been
successfully completedrw Integer32 .1.3.6.1.4.1.248.14.1.10.12.2 |
hmRS2PSGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.1.10.13 |
hmRS2PSAlarmEnables/disables an alarm for the signalling relay of the
powersupply state.rw Enumeration .1.3.6.1.4.1.248.14.1.10.13.1 |
hmRS2RedundancyGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.1.10.14 |
hmRS2RedNotGuaranteedAlarmWhen enabled the message 'redundancy not guaranteed' will be
signalled on the signalling relay.rw Enumeration .1.3.6.1.4.1.248.14.1.10.14.1 |
hmRS4RGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.1.10.15 |
hmRS4RVlanGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.1.10.15.1 |
hmRS4RVlanPortTableThis table describes private vlan enhancements of rs2-4r devices. SEQUENCE OF HmRS4RVlanPortEntry .1.3.6.1.4.1.248.14.1.10.15.1.1 |
hmRS4RVlanPortEntryThe entry of the hmRS4RVlanPortTable. HmRS4RVlanPortEntry .1.3.6.1.4.1.248.14.1.10.15.1.1.1 |
hmRS4RVlanPortIDThis index is used to identify the port. Integer32 .1.3.6.1.4.1.248.14.1.10.15.1.1.1.1 |
hmRS4RVlanPortTagFormatRstpWhen enabled all tags are removed when sending packets on the port (egress).
When disabled tag format is not changed, but RSTP frames are sent tagged.
This variable is only used if RSTP is enabled.
The default value is enable.rw Enumeration .1.3.6.1.4.1.248.14.1.10.15.1.1.1.2 |
hmRS2FDBGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.1.10.16 |
hmRS2FDBHashGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.1.10.16.1 |
hmRS2FDBHashOptimizingModeEnables/disables the hash optimizing mode on this device.
When enabled the switch will use another hash algorithm
optimized for incrementing addresses.
After setting this variable the switch have to be reset.
The default value is disable.rw Enumeration .1.3.6.1.4.1.248.14.1.10.16.1.1 |
hmRS2FDBHashOptimizingStatusShows the current hash mode of this device.
When enabled the switch uses the optimized hash mode,
else the normal mode.ro Enumeration .1.3.6.1.4.1.248.14.1.10.16.1.2 |
hmMACH3ChassisExt OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.1.11 |
hmSelfTestResults OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.1.11.1 |
hmSelfTestCpuResultResult of the selftest coded as an integer value
with each bit representing the result of a different
sub part test. Bits 0..15 set in the result indicate
warning conditions, bits 16..31 indicate error
conditions of the sub part tests.
Meaning of the bits:
Bit 0: default configuration activated and running
Bit 2: BB_DATAMEM_ERROR caused by log-entry:
S_mmcssp_CRC_ERROR_DATAMEM ( in mmcNP5400Int() )
S_mmcssp_LEN_ERROR_DATAMEM ( in mmcNP5400Int() )
Bit 3: BB_PARITY_ERROR caused by log-entry:
S_mmcssp_PER_ON_VIX_OR_IPC ( in mmcNP5400Int() )
S_mmcssp_PE_PIF_VIX_DATA ( in mmcEpifPintProc(), mmcGpifPintProc(), mmcXpifPintProc() )
S_mmcssp_PE_PIF_GGI ( in mmcGpifPintProc(), mmcXpifPintProc() )
Bit 4: BOOT_ERROR_PIF caused by log-entry:
S_mmcssp_PIF_BOOT_ERROR ( in mmcEpifPintProc(), mmcGpifPintProc(), mmcXpifPintProc() )
Bit 5: MMC_PORT_PROBLEM caused by log-entry:
S_mmcssp_WRONG_PORT_IN_MSG ( in mmcGotAliveMsg() )
S_mmcssp_NO_ADDRESS_FOR_PORT ( in mmcPortConfig() )
Bit 16: configuration data in bootblock of flash was invalid through startup
Bit 17: configuration in flash is corruptedro Integer32 .1.3.6.1.4.1.248.14.1.11.1.1 |
hmSelfTestBBResultResult of the selftest coded as an integer value
with each bit representing the result of a different
sub part test. Bits set in the result indicate error
conditions of the sub part tests.
Meaning of the bits:
Bit 0: selftest error of backplane port no 1
Bit 1: selftest error of backplane port no 2
Bit 2: selftest error of backplane port no 3
Bit 3: selftest error of backplane port no 4
Bit 8: selftest error of network processor no 1
Bit 9: selftest error of network processor no 2
Bit 10: selftest error of network processor no 3
Bit 11: selftest error of network processor no 4
Bit 12: selftest error of xpif no 1
Bit 13: selftest error of xpif no 2
Bit 14: selftest error of xpif no 3
Bit 15: selftest error of xpif no 4
Bit 16: error packet memory size
Bit 30: error on board eepromro Integer32 .1.3.6.1.4.1.248.14.1.11.1.2 |
hmSelfTestBPResultResult of the selftest coded as an integer value
with each bit representing the result of a different
sub part test. Bits set in the result indicate error
conditions of the sub part tests.
Meaning of the bits:
Bit 0: communication error with card 1
Bit 1: communication error with card 2
Bit 2: communication error with card 3
Bit 3: communication error with card 4
Bit 4: communication error with card 5
Bit 24: main and redundant eeprom 2 are different
Bit 25: main and redundant eeprom 1 are different
Bit 27: error on redundant eeprom 2
Bit 28: error on redundant eeprom 1
Bit 29: error on main eeprom 2
Bit 30: error on main eeprom 1ro Integer32 .1.3.6.1.4.1.248.14.1.11.1.3 |
hmSelfTestM1ResultResult of the selftest coded as an integer value
with each bit representing the result of a different
sub part test. Bits set in the result indicate error
conditions of the sub part tests.
Meaning of the bits:
Bit 0: selftest error of port no 1
Bit 1: selftest error of port no 2
Bit 2: selftest error of port no 3
Bit 3: selftest error of port no 4
Bit 4: selftest error of port no 5
Bit 5: selftest error of port no 6
Bit 6: selftest error of port no 7
Bit 7: selftest error of port no 8
Bit 16: selftest error of pif no 1
Bit 17: selftest error of pif no 2
Bit 30: error on module eepromro Integer32 .1.3.6.1.4.1.248.14.1.11.1.4 |
hmSelfTestM2ResultResult of the selftest coded as an integer value
with each bit representing the result of a different
sub part test. Bits set in the result indicate error
conditions of the sub part tests.
Meaning of the bits:
Bit 0: selftest error of port no 1
Bit 1: selftest error of port no 2
Bit 2: selftest error of port no 3
Bit 3: selftest error of port no 4
Bit 4: selftest error of port no 5
Bit 5: selftest error of port no 6
Bit 6: selftest error of port no 7
Bit 7: selftest error of port no 8
Bit 16: selftest error of pif no 1
Bit 17: selftest error of pif no 2
Bit 30: error on module eepromro Integer32 .1.3.6.1.4.1.248.14.1.11.1.5 |
hmSelfTestM3ResultResult of the selftest coded as an integer value
with each bit representing the result of a different
sub part test. Bits set in the result indicate error
conditions of the sub part tests.
Meaning of the bits:
Bit 0: selftest error of port no 1
Bit 1: selftest error of port no 2
Bit 2: selftest error of port no 3
Bit 3: selftest error of port no 4
Bit 4: selftest error of port no 5
Bit 5: selftest error of port no 6
Bit 6: selftest error of port no 7
Bit 7: selftest error of port no 8
Bit 16: selftest error of pif no 1
Bit 17: selftest error of pif no 2
Bit 30: error on module eepromro Integer32 .1.3.6.1.4.1.248.14.1.11.1.6 |
hmSelfTestM4ResultResult of the selftest coded as an integer value
with each bit representing the result of a different
sub part test. Bits set in the result indicate error
conditions of the sub part tests.
Meaning of the bits:
Bit 0: selftest error of port no 1
Bit 1: selftest error of port no 2
Bit 2: selftest error of port no 3
Bit 3: selftest error of port no 4
Bit 4: selftest error of port no 5
Bit 5: selftest error of port no 6
Bit 6: selftest error of port no 7
Bit 7: selftest error of port no 8
Bit 16: selftest error of pif no 1
Bit 17: selftest error of pif no 2
Bit 30: error on module eepromro Integer32 .1.3.6.1.4.1.248.14.1.11.1.7 |
hmSelfTestModeSetting this variable to enable(1) results in a full
report of all detected selftest errors.
The default value is disable(2).rw Enumeration .1.3.6.1.4.1.248.14.1.11.1.8 |
hmMgmtBusSelectedthis variable indicates which management bus is selected.ro Enumeration .1.3.6.1.4.1.248.14.1.11.2 |
hmSerialNumbers OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.1.11.3 |
hmSerialNumCpuSerial Number of the CPU board.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.248.14.1.11.3.1 |
hmSerialNumBBSerial Number of the basic board.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.248.14.1.11.3.2 |
hmSerialNumBPSerial Number of the packplane unit.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.248.14.1.11.3.3 |
hmSerialNumM1Serial Number of module 1.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.248.14.1.11.3.4 |
hmSerialNumM2Serial Number of module 2.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.248.14.1.11.3.5 |
hmSerialNumM3Serial Number of module 3.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.248.14.1.11.3.6 |
hmSerialNumM4Serial Number of module 4.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.248.14.1.11.3.7 |
hmPlugAndPlay OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.1.11.4 |
hmAutoConfigStatestate of the configuration retrieval from a neighbour cardro Enumeration .1.3.6.1.4.1.248.14.1.11.4.1 |
hmMACH3Misc OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.1.11.5 |
hmUserGroupStatusstate of the user group configurationro Enumeration .1.3.6.1.4.1.248.14.1.11.5.1 |
hmAUIGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.1.12 |
hmAUIModuleTableThis table contains all AUI variables
that are module dependend. SEQUENCE OF HmAUIModuleEntry .1.3.6.1.4.1.248.14.1.12.10 |
hmAUIModuleEntryThe entry of the hmAUIModuleTable. HmAUIModuleEntry .1.3.6.1.4.1.248.14.1.12.10.1 |
hmAUIModuleIDThis index is used to identify a specific module.ro Integer32 .1.3.6.1.4.1.248.14.1.12.10.1.1 |
hmAUIModuleDTEPowerMonitorThis variable shows the DTE Power Monitor DIP switch
setting on the AUI module.ro Enumeration .1.3.6.1.4.1.248.14.1.12.10.1.2 |
hmAUIPortTableThis table contains all AUI variables
that are port dependend. SEQUENCE OF HmAUIPortEntry .1.3.6.1.4.1.248.14.1.12.11 |
hmAUIPortEntryThe entry of the hmAUIPortTable. HmAUIPortEntry .1.3.6.1.4.1.248.14.1.12.11.1 |
hmAUIPortIDThis index is used to identify a specific port.ro Integer32 .1.3.6.1.4.1.248.14.1.12.11.1.1 |
hmAUIPortDTEPowerThis variable shows the DTE Power value
of the AUI port.ro Enumeration .1.3.6.1.4.1.248.14.1.12.11.1.2 |
hmAUIPortSQETestThis variable shows the SQE Test DIP switch
setting on the AUI port.ro Enumeration .1.3.6.1.4.1.248.14.1.12.11.1.3 |
hmAgent OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.2 |
hmAgentEventThe events of hmAgent. OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.2.0 |
hmTemperatureTrapThis trap is sent if the value of hmTemperature leaves or
enters the range of the agent temperature threshholds
hmTempUprLimit and hmTempLwrLimit. NOTIFICATION-TYPE .1.3.6.1.4.1.248.14.2.0.1 |
hmLoginTrapThis trap is sent if a user attemps to login via telnet
or serial connection. hmLastIpAddr contains the IP address of the
login request. the value is 0.0.0.0, if the request was sent via serial
connection. hmLastCommunity contains the used password. If the login was
successfull, '******' will be sent instead. NOTIFICATION-TYPE .1.3.6.1.4.1.248.14.2.0.2 |
hmDuplicateStaticAddressTrapThis trap is sent if a user attemps to set the same static unicast
address at more than one agent of a chassis NOTIFICATION-TYPE .1.3.6.1.4.1.248.14.2.0.3 |
hmAutoconfigAdapterTrapThis trap reports a status change of the Autoconfiguration Adapter. NOTIFICATION-TYPE .1.3.6.1.4.1.248.14.2.0.4 |
hmRelayDuplicateIPTrapThis trap reports the detection of a duplicate ip address
by the relay agent. NOTIFICATION-TYPE .1.3.6.1.4.1.248.14.2.0.5 |
hmSNTPTrapThis trap reports SNTP error conditions. For a list of
possible error conditions refer to hmNetSNTPOperStatus. NOTIFICATION-TYPE .1.3.6.1.4.1.248.14.2.0.6 |
hmNetACDNotificationThis trap reports an address conflict detection. NOTIFICATION-TYPE .1.3.6.1.4.1.248.14.2.0.7 |
hmConfigurationSavedTrapThis trap is sent after the configuration of the
agent was successfully saved. NOTIFICATION-TYPE .1.3.6.1.4.1.248.14.2.0.8 |
hmConfigurationChangedTrapThis trap is sent if the local and the running
configuration doesn't match. NOTIFICATION-TYPE .1.3.6.1.4.1.248.14.2.0.9 |
hmAddressRelearnDetectTrapThis trap is sent if the relearn threshold is exceeded. NOTIFICATION-TYPE .1.3.6.1.4.1.248.14.2.0.10 |
hmDuplexMismatchTrapThis trap indicates a possible serious situation.
Check for duplex mismatch, or EMI, or too many cascaded hubs, or exceeded maximum distance at HDX port. NOTIFICATION-TYPE .1.3.6.1.4.1.248.14.2.0.11 |
hmNTPTrapThis trap reports NTP error conditions. For a list of
possible error conditions refer to hmNetNTPStatusCode. NOTIFICATION-TYPE .1.3.6.1.4.1.248.14.2.0.12 |
hmPortMonitorPortDisabledTrapThis trap is sent if a port has been disabled by port disable action by port monitor. NOTIFICATION-TYPE .1.3.6.1.4.1.248.14.2.0.13 |
hmPOEModulePowerUsageOnNotificationThis trap reports POE error condition. This Notification
indicate PSE Threshold usage indication is on, the usage power
is above the threshold. At least 500 msec must elapse between
notifications being emitted by the same object instance. NOTIFICATION-TYPE .1.3.6.1.4.1.248.14.2.0.14 |
hmPOEModulePowerUsageOffNotificationThis trap reports POE error condition. This Notification
indicate PSE Threshold usage indication is on, the usage power
is below the threshold. At least 500 msec must elapse between
notifications being emitted by the same object instance. NOTIFICATION-TYPE .1.3.6.1.4.1.248.14.2.0.15 |
hmSysSelftestPortErrorThis trap is sent when the agent wants to reboot due to Opal Workaround 4. It shows
that the specific port is in an error state and a device reboot is needed. NOTIFICATION-TYPE .1.3.6.1.4.1.248.14.2.0.16 |
hmActionThis object, when read, always returns a value of other(1).
A value of reset(2) has the same effect as a power-on sequence
(coldstart). Writing a value of hotRestart(10) leads to a warmstart.
When set to resetStats(3), a reset of all statistic
counters within the whole switch will be forced. A value of
resetFDB(4) will clear the forwarding database.
If set to resetARP(5), the ARP table will be flushed.
The value gbl-reset(12) will result in a reset of the whole
chassis. Any other value results in a badValue status code.rw Enumeration .1.3.6.1.4.1.248.14.2.1 |
hmActionResultResult of the last activated action. A value of zero
indicates that the result is ok. Bits set in the result
indicate error conditions.ro Integer32 .1.3.6.1.4.1.248.14.2.2 |
hmNetwork OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.2.3 |
hmNetLocalIPAddrIP address of the management agent board.
Changing this value will take effect after activating with hmNetAction.rw IpAddress .1.3.6.1.4.1.248.14.2.3.1 |
hmNetLocalPhysAddrPhysical base address (MAC-address) of the agent.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.248.14.2.3.2 |
hmNetGatewayIPAddrIP address of the default gateway.
Changing this value will take effect after activating with hmNetAction.rw IpAddress .1.3.6.1.4.1.248.14.2.3.3 |
hmNetMaskSubnet mask.
Changing this value will take effect after activating with hmNetAction.rw IpAddress .1.3.6.1.4.1.248.14.2.3.4 |
hmNetPPPBaseIPAddrBase address of the IP address range used by the
point-to-point protocol. The IP addresses
hmNetPPPBaseAddress..hmNetPPPBaseAddress+4 are assigned
to the client machines attached to management agents 1..5.
The management agents can be reached using addresses
hmNetPPPBaseAddress+10..hmNetPPPBaseAddress+14.
Changing this variable on one agent automatically updates
the value on the other agents in the same chassis.rw IpAddress .1.3.6.1.4.1.248.14.2.3.5 |
hmNetPPPNetMaskSubnet mask used by the point-to-point protocol.
Changing this variable on one agent automatically updates
the value on the other agents in the same chassis.rw IpAddress .1.3.6.1.4.1.248.14.2.3.6 |
hmNetActionThis object, when read, always returns a value of other(1).
Setting the object to activate(2) causes a reconfiguration
of the IP protocol stack with the current values of
hmNetLocalIPAddr, hmNetGatewayIPAddr and hmNetMask.rw Enumeration .1.3.6.1.4.1.248.14.2.3.7 |
hmNetVlanIDVlan ID of the IP protocol stack. If the value is 0,
Traffic from all Vlans is accepted. Every other value means
that only traffic of the appropriate Vlan is accepted and outgoing
traffic uses this Vlan ID.rw Integer32 .1.3.6.1.4.1.248.14.2.3.8 |
hmNetLocalPhysAddrRangeThe number of MAC addresses reserved for this device, starting from hmNetLocalPhysAddr.ro Integer32 .1.3.6.1.4.1.248.14.2.3.9 |
hmNetVlanPriorityVlan Priority which is used in management replies.rw Integer32 .1.3.6.1.4.1.248.14.2.3.10 |
hmNetIpDscpPriorityIP DSCP value which is used in management replies.rw Integer32 .1.3.6.1.4.1.248.14.2.3.11 |
hmNetACDGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.2.3.12 |
hmNetACDStatusSets the mode of the ip address conflict detection mechanism on this device.
enable(1): Both active and passive detection are active.
disable(2): No detection takes place.
activeDetectionOnly(3): During configuration of a local ip address
the device actively probes the network for this ip address.
passiveDetectionOnly(4): The device listens passively on the network
if another device with an already locally configured ip address appears.
In this case the own ip address is actively defended by transmitting gratituous arp's.rw Enumeration .1.3.6.1.4.1.248.14.2.3.12.1 |
hmNetACDOngoingProbeStatusIf enabled, the device sends periodic arp probes.rw Enumeration .1.3.6.1.4.1.248.14.2.3.12.3 |
hmNetACDDelayThe maximum detection delay time in milliseconds.
Time gap between arp probes.rw Integer32 .1.3.6.1.4.1.248.14.2.3.12.5 |
hmNetACDReleaseDelayDelay in seconds to the next arp probe cycle
after an ip address conflict was detected.rw Integer32 .1.3.6.1.4.1.248.14.2.3.12.7 |
hmNetACDMaxProtectionMaximum number of frequent address protections.rw Integer32 .1.3.6.1.4.1.248.14.2.3.12.9 |
hmNetACDProtectIntervalDelay in milliseconds between two protections.rw Integer32 .1.3.6.1.4.1.248.14.2.3.12.11 |
hmNetACDFaultStatetrue(1) if an active address conflict is detected.
false(2) if no present address conflict.ro Enumeration .1.3.6.1.4.1.248.14.2.3.12.13 |
hmNetACDAddrTableThis table contains address conflict detection information
on the local system known to this agent. SEQUENCE OF HmNetACDAddrEntry .1.3.6.1.4.1.248.14.2.3.12.20 |
hmNetACDAddrEntryIP Address conflict detection information about a particular
address on the local system kown to this agent.
There may be multiple addresses configured on the system.
Entries may be created and deleted in this table by the
agent. HmNetACDAddrEntry .1.3.6.1.4.1.248.14.2.3.12.20.1 |
hmNetACDTimeMarkA TimeFilter for this entry. See the TimeFilter textual
convention in IETF RFC 2021 and
http://www.ietf.org/IESG/Implementations/RFC2021-Implementation.txt
to see how TimeFilter works.ro TimeFilter (RMON2-MIB) .1.3.6.1.4.1.248.14.2.3.12.20.1.1 |
hmNetACDAddrSubtypeThe type of management address identifier encoding used in
the associated 'hmNetACDAddr' object.ro AddressFamilyNumbers (IANA-ADDRESS-FAMILY-NUMBERS-MIB) .1.3.6.1.4.1.248.14.2.3.12.20.1.3 |
hmNetACDAddrThe string value used to identify the management address
component associated with the local system.ro OCTET STRING .1.3.6.1.4.1.248.14.2.3.12.20.1.5 |
hmNetACDMACThe physical address of the device that was detected
causing the ip address conflict.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.248.14.2.3.12.20.1.7 |
hmNetACDIfIdThe integer value used to identify the interface number
on the local system where the ip address conflict was detected.ro Integer32 .1.3.6.1.4.1.248.14.2.3.12.20.1.9 |
hmNetHiDiscoveryGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.2.3.20 |
hmNetHiDiscoveryStatusEnables/disables the HiDiscovery protocol
on this device.
This protocol allows a remote host to detect
devices without an ip configuration.
It also allows the host to set ip parameters,
like the ip address, the netmask and
the gateway address.
If only detection and no configuration is allowed
set this object to readOnly(3).rw Enumeration .1.3.6.1.4.1.248.14.2.3.20.1 |
hmNetHiDiscoveryRelayRelay/bridge HiDiscovery frames.rw Enumeration .1.3.6.1.4.1.248.14.2.3.20.2 |
hmNetSNTPGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.2.3.30 |
hmNetSNTPStatusEnables/disables the Simple Network Time Protocol
on this device.rw Enumeration .1.3.6.1.4.1.248.14.2.3.30.1 |
hmNetSNTPServerThe IP Address of an external Time Server.rw IpAddress .1.3.6.1.4.1.248.14.2.3.30.2 |
hmNetSNTPTimeThe time in seconds since 01/01/1900 UTC.rw TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.248.14.2.3.30.3 |
hmNetSNTPLocalOffsetThe difference between local time and UTC in minutes.rw Integer32 (-1000..1000) .1.3.6.1.4.1.248.14.2.3.30.4 |
hmNetSNTPServer2IP address of a secondary (backup) time server.rw IpAddress .1.3.6.1.4.1.248.14.2.3.30.5 |
hmNetSNTPSyncIntervalSNTP synchronisation interval in seconds.rw Integer32 .1.3.6.1.4.1.248.14.2.3.30.6 |
hmNetSNTPAcceptBroadcastsThis MIB variable specifies whether SNTP broadcasts will
be allowed to synchronize the local clock.
If hmNetSNTPStatus is enabled,
this variable will be ignored and broadcasts will not set
the local clock.rw Enumeration .1.3.6.1.4.1.248.14.2.3.30.7 |
hmNetSNTPAnycastAddrDestination address for SNTP broadcasts.
A broadcast, multicast or unicast address may be specified.
Setting the address to 0.0.0.0 disables SNTP broadcasts.rw IpAddress .1.3.6.1.4.1.248.14.2.3.30.8 |
hmNetSNTPAnycastVlanVlan for anycast mode.rw Integer32 .1.3.6.1.4.1.248.14.2.3.30.9 |
hmNetSNTPAnycastIntervalInterval of SNTP broadcast messages in seconds.rw Integer32 .1.3.6.1.4.1.248.14.2.3.30.10 |
hmNetSNTPOperStatusOperational status of the SNTP sub-system.
The value is a bit mask:
1 local system clock synchronized
2 SNTP loop detected
4 generic error
8 once synced, client disabled
100 server 1 not synchronized
200 server 1 bad protocol version
400 server 1 not responding
10000 server 2 not synchronized
20000 server 2 bad protocol version
40000 server 2 not responding
(Note that all values are hexadecimal.)ro Integer32 .1.3.6.1.4.1.248.14.2.3.30.11 |
hmNetSNTPTimeAdjustThresholdThe threshold in milli-seconds whether to decide to set the received
SNTP time directly to the local clock or not. If the hmNetSNTPTimeAdjustThreshold
value is 0, the received SNTP time will be set directly to the local clock every
time a SNTP message is received. If the difference between the local clock time
and the received SNTP time is fewer than the hmNetSNTPTimeAdjustThreshold
value, the local clock will not be set. If the difference between the local clock time
and the received SNTP time is equal or larger than the hmNetSNTPTimeAdjustThreshold
value, the local clock will be set.rw Integer32 .1.3.6.1.4.1.248.14.2.3.30.12 |
hmNetSNTPOnceAtStartupIf enabled, SNTP ist automaticaly disabled after once synchronized to an SNTP Server.rw Enumeration .1.3.6.1.4.1.248.14.2.3.30.13 |
hmNetSNTPServerOnlyIfSyncThe SNTP server is enabled only if synchronized to another external time reference. (e.g. SNTP or PTP)rw Enumeration .1.3.6.1.4.1.248.14.2.3.30.14 |
hmNetSNTPServerStatusEnables/disables the SNTP server on this device if hmNetSNTPStatus is enabled.rw Enumeration .1.3.6.1.4.1.248.14.2.3.30.15 |
hmNetSNTPClientStatusEnables/disables the SNTP client on this device if hmNetSNTPStatus is enabled.rw Enumeration .1.3.6.1.4.1.248.14.2.3.30.16 |
hmNetNTPGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.2.3.31 |
hmNetNTPOperationSelects operation mode for NTP.rw Enumeration .1.3.6.1.4.1.248.14.2.3.31.1 |
hmNetNTPServer1AddrTypeAddress type for server 1.
Currently, only ipv4 is supported.rw InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.248.14.2.3.31.2 |
hmNetNTPServer1AddressThe address of the first external time server.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.248.14.2.3.31.3 |
hmNetNTPServer2AddrTypeAddress type for server 2.
Currently, only ipv4 is supported.rw InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.248.14.2.3.31.4 |
hmNetNTPServer2AddressThe address of the second external time server.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.248.14.2.3.31.5 |
hmNetNTPSyncIntervalNTP synchronisation interval in seconds.
NTP will round down the value to a power of 2.
The protocol will use an interval between the
rounded value and the next power of 2.rw Integer32 .1.3.6.1.4.1.248.14.2.3.31.6 |
hmNetNTPAnycastAddrTypeAddress type for anycasts.
Currently, only ipv4 is supported.rw InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.248.14.2.3.31.7 |
hmNetNTPAnycastAddressDestination address for NTP broadcasts.
A broadcast, multicast or unicast address may be specified.
Setting the address to 0.0.0.0 disables NTP broadcasts.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.248.14.2.3.31.8 |
hmNetNTPAnycastIntervalInterval of NTP broadcast messages in seconds.
NTP will round down the value to a power of 2.rw Integer32 .1.3.6.1.4.1.248.14.2.3.31.9 |
hmNetNTPStatusTextOperational status of the NTP sub-system.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.248.14.2.3.31.10 |
hmNetNTPStatusCodeOperational status of the NTP sub-system.
The value is a bit mask:
1 local system clock synchronized
2 generic error (see hmNetNTPStatusText)
100 server 1 not synchronized
200 server 1 protocol error
400 server 1 not responding
800 server 1 synchronization in progress
10000 server 2 not synchronized
20000 server 2 protocol error
40000 server 2 not responding
80000 server 2 synchronization in progress
(Note that all values are hexadecimal.)ro Integer32 .1.3.6.1.4.1.248.14.2.3.31.11 |
hmNetPTPGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.2.3.40 |
hmNetPTPConfiguration OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.2.3.40.1 |
hmNetPTPEnableEnable or disable the Precision Time Protocol
on this node.rw Enumeration .1.3.6.1.4.1.248.14.2.3.40.1.1 |
hmNetPTPActionInitialize the PTP Clock. Value 2: The specification
initialization set shall be used. Value 3: The initialization
set stored in nonvolatile storage for recovery
after a power fail shall be used. Value 1: no action.
In GET operations the variable always returns other(1)rw Enumeration .1.3.6.1.4.1.248.14.2.3.40.1.2 |
hmNetPTPClockModeThis members value shall indicate which clock mode is used.
The ptp-mode-boundary-clock mode specifies the mode as described in the IEEE1588 standard.
In the 'ptp-mode-simple-ptp' mode the device only accepts PTP sync messages, sets the time
directly and no BMC algorithm will run. If the clock mode is changed, PTP will be initialized.rw Enumeration .1.3.6.1.4.1.248.14.2.3.40.1.3 |
hmNetPTPSlavePortThis members value shall indicate the slave port where this clock is synchronized
in the ptp-mode-static-boundary-clock mode.
The default value is 0 (i.e. clock is grandmaster).rw Integer32 .1.3.6.1.4.1.248.14.2.3.40.1.4 |
hmNetPTPIsSynchronizedIf the clock is synchronized to the current Master this object is set to true.
Otherwise it is set to false. The clock sets this object to true, if the offset (ns)
to the current Master is less than hmNetPTPSyncLowerBound. The clock sets this object to false,
if the offset (ns) to the current Master is bigger than hmNetPTPSyncUpperBound.ro Enumeration .1.3.6.1.4.1.248.14.2.3.40.1.5 |
hmNetPTPSyncLowerBoundThis object defines when the hmNetPTPIsSynchronized object is set to true.
If the absolute value of the offset is smaller than hmNetPTPSyncLowerBound,
the hmNetPTPIsSynchronized is set true.
The value is interpreted as nanoseconds.rw Integer32 .1.3.6.1.4.1.248.14.2.3.40.1.6 |
hmNetPTPSyncUpperBoundThis object defines when the hmNetPTPIsSynchronized object is set to false.
If the absolute value of the offset is bigger than hmNetPTPSyncUpperBound, the hmNetPTPIsSynchronized is set false.
The value is interpreted as nanoseconds.rw Integer32 .1.3.6.1.4.1.248.14.2.3.40.1.7 |
hmNetPTPClockStratumThe clock stratum, or stratum number,
describes one measure of the quality of a clock. Each clock
shall be characterized by a stratum number to be used by
the best master clock algorithm as one parameter of clock
quality. A clock stratum of 1 is the best,
where the default clock stratum is 255.ro Integer32 .1.3.6.1.4.1.248.14.2.3.40.1.8 |
hmNetPTPClockIdentifierThe clock identifier indicates the nature and expected
absolute accuracy and epoch of a given clock. Possible
values are ATOM, GPS, NTP, HAND, INIT, DFLT. Values with
less characters than the maximum allowed length will be
padded with zero characters.ro OCTET STRING .1.3.6.1.4.1.248.14.2.3.40.1.9 |
hmNetPTPClockVarianceThe clock variance reflects the inherent characteristics of the clock.
It is an estimate of the local clock from a linear time scale when it
is not synchronized to another PTP clock using the PTP protocol.rw Integer32(-32768..32767) .1.3.6.1.4.1.248.14.2.3.40.1.10 |
hmNetPTPPreferredMasterA clock may be administratively designated as part of a
preferred master clock set. This creates a set of clocks
that will be favored over those not so designated in the
selection of master clocks within a subdomain. The purpose
of this designation is to allow users to specify a clock
that will remain master in the presence of disconnection
or connection of other clocks.rw Enumeration .1.3.6.1.4.1.248.14.2.3.40.1.11 |
hmNetPTPSyncIntervalThe sync interval shall be the interval in seconds between
successive Sync messages issued by master clocks.
It shall have the same value for all clocks in a subdomain.
The value of sync interval is a compromise between the
inherent stability of the clocks, the responsiveness of the
clocks in a subdomain to change, and the communication load
imposed by PTP. Allowed values are 1,2,8,16 and 64.
Changes are applied after the initialization with the init
key init-with-nvm or after reboot if the configuration was saved.rw Enumeration .1.3.6.1.4.1.248.14.2.3.40.1.12 |
hmNetPTPSubdomainNameEach subdomain shall be characterized by a name recognized
by all PTP clocks in the subdomain as the basis for sending
and receiving PTP communications. Changes are applied after
the initialization with the init key init-with-nvm or afer
reboot if the configuration was saved. The values of the
octets for the subdomain name may be chosen from the set
consisting of the values of the printable ASCII characters
starting with hex value 0x21 (!) up to and including hex
value 0x7E (~).rw OCTET STRING .1.3.6.1.4.1.248.14.2.3.40.1.13 |
hmNetPTPOffsetFromMasterNanoSecsCurrent offset between its parent and this node in nanoseconds.
Values greater than 1 second or less than -1 second are
indicated by the maximum or minimum INTEGER values.ro Integer32 .1.3.6.1.4.1.248.14.2.3.40.1.14 |
hmNetPTPAbsMaxOffsetThis members value shall indicate the absolute value for the maximum offset between its parent and this node.
The value is set to zero if the offset is the first time smaller than hmNetPTPSyncLowerBound.
Offsets bigger than +/-1 second is indicated by the maximum valuero Integer32 .1.3.6.1.4.1.248.14.2.3.40.1.15 |
hmNetPTPOneWayDelayNanoSecsCurrent one_way_delay between its parent and this node in nanoseconds.
Values greater than 1 second or less than -1 second are
indicated by the maximum or minimum INTEGER values.ro Integer32 .1.3.6.1.4.1.248.14.2.3.40.1.16 |
hmNetPTPTimeSecondsThis members value shall indicate PTP time in seconds since 1.1.1970.ro Integer32 .1.3.6.1.4.1.248.14.2.3.40.1.17 |
hmNetPTPObservedDriftRelative rate (frequency or drift) between its parent and this node in nanoseconds.
Values greater than 1 second or less than -1 second are
indicated by the maximum or minimum INTEGER values.ro Integer32 .1.3.6.1.4.1.248.14.2.3.40.1.18 |
hmNetPTPPiIntegralA digital PI servo has the following difference equation
y(k) = y(k-1) + (Kp + Ki* T )* x(k) + Kp * x(k-1).
This object specifies the Ki* 100000 term (integral part). Kp is 0.5.
The default value of this object is 6250 that is Ki=1/16.rw Integer32 .1.3.6.1.4.1.248.14.2.3.40.1.19 |
hmNetPTPParentUUIDThe UUID of its Parent. For Ethernet this is the MAC
address of the management agent.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.248.14.2.3.40.1.20 |
hmNetPTPGrandmasterUUIDThe UUID of its Grandmaster. For Ethernet this is the MAC
address of the management agent.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.248.14.2.3.40.1.21 |
hmNetPTPCurrentUTCOffsetUTC time differs from the TAI time by a constant offset.
This offset is modified on occasion by adding or subtracting
leap seconds. The current number of leap seconds is represented
in PTP by the value of hmNetPTPCurrentUTCOffset.ro Integer32 .1.3.6.1.4.1.248.14.2.3.40.1.22 |
hmNetPTPleap59When TRUE the last minute of the current day will contain 59 seconds.ro Enumeration .1.3.6.1.4.1.248.14.2.3.40.1.23 |
hmNetPTPleap61When TRUE the last minute of the current day will contain 61 seconds.ro Enumeration .1.3.6.1.4.1.248.14.2.3.40.1.24 |
hmNetPTPStepsRemovedThis members value shall be the number of communication paths traversed between the local clock and
the grandmaster clock. For example, steps_removed in a slave clock on the same PTP communication path as
the grandmaster clock will have a value of 1, indicating that a single path was traversed.ro Integer32 .1.3.6.1.4.1.248.14.2.3.40.1.25 |
hmNetPTPEpochNumberThe PTP epoch began at 0 hours on 1 January 1970. Times measured
since this epoch are designated in this standard as PTP Seconds.
When the epoch is the PTP epoch, the value of the epoch number
shall be the current number of times the 32-bit seconds clock
has rolled over since the PTP epoch.ro Integer32 .1.3.6.1.4.1.248.14.2.3.40.1.26 |
hmNetPTPStaticDriftRelative rate (frequency or drift) between a reference clock and this node
in nanoseconds per second (ns/s). This value is only applied if no port is in
slave state.rw Integer32 (-500000000..500000000) .1.3.6.1.4.1.248.14.2.3.40.1.27 |
hmNetPTPPortTableThis table contains variables for each PTP port of
the switch. SEQUENCE OF HmNetPTPPortEntry .1.3.6.1.4.1.248.14.2.3.40.2 |
hmNetPTPPortEntryEntry for one port. HmNetPTPPortEntry .1.3.6.1.4.1.248.14.2.3.40.2.1 |
hmNetPTPPortIDIndex to identify a port of the switch unit.
This value is never greater than hmSysGroupCapacity.ro Integer32 .1.3.6.1.4.1.248.14.2.3.40.2.1.1 |
hmNetPTPPortStateState of the PTP port intance.ro Enumeration .1.3.6.1.4.1.248.14.2.3.40.2.1.2 |
hmNetPTPPortBurstEnableControls the burst enable flag.rw Enumeration .1.3.6.1.4.1.248.14.2.3.40.2.1.3 |
hmNetPTPPortEnableThe respective PTP Port of the Boundary Clock can be set to true (enabled) or set to false (disabled).
If the port is disabled no PTP packets will be processed for the respective port.rw Enumeration .1.3.6.1.4.1.248.14.2.3.40.2.1.4 |
hmNetPTP2Group OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.2.3.41 |
hmNetPTP2Configuration OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.2.3.41.1 |
hmNetPTP2TwoStepClockro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.248.14.2.3.41.1.1 |
hmNetPTP2ClockIdentityro PTPClockIdentity .1.3.6.1.4.1.248.14.2.3.41.1.2 |
hmNetPTP2Priority1rw Integer32 .1.3.6.1.4.1.248.14.2.3.41.1.3 |
hmNetPTP2Priority2rw Integer32 .1.3.6.1.4.1.248.14.2.3.41.1.4 |
hmNetPTP2DomainNumberrw Integer32 .1.3.6.1.4.1.248.14.2.3.41.1.5 |
hmNetPTP2StepsRemovedro Integer32 .1.3.6.1.4.1.248.14.2.3.41.1.6 |
hmNetPTP2OffsetFromMasterro PTPTimeInterval .1.3.6.1.4.1.248.14.2.3.41.1.7 |
hmNetPTP2MeanPathDelayro PTPTimeInterval .1.3.6.1.4.1.248.14.2.3.41.1.8 |
hmNetPTP2ParentPortIdentityro PTPPortIdentity .1.3.6.1.4.1.248.14.2.3.41.1.9 |
hmNetPTP2ParentStatsro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.248.14.2.3.41.1.10 |
hmNetPTP2ObservedParentOffsetScaledLogVariancero Integer32 .1.3.6.1.4.1.248.14.2.3.41.1.11 |
hmNetPTP2ObservedParentClockPhaseChangeRatero Integer32 .1.3.6.1.4.1.248.14.2.3.41.1.12 |
hmNetPTP2GrandmasterIdentityro PTPClockIdentity .1.3.6.1.4.1.248.14.2.3.41.1.13 |
hmNetPTP2GrandmasterClockQualityro PTPClockQuality .1.3.6.1.4.1.248.14.2.3.41.1.14 |
hmNetPTP2GrandmasterPriority1ro Integer32 .1.3.6.1.4.1.248.14.2.3.41.1.15 |
hmNetPTP2GrandmasterPriority2ro Integer32 .1.3.6.1.4.1.248.14.2.3.41.1.16 |
hmNetPTP2CurrentUtcOffsetrw Integer32 .1.3.6.1.4.1.248.14.2.3.41.1.17 |
hmNetPTP2CurrentUtcOffsetValidrw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.248.14.2.3.41.1.18 |
hmNetPTP2Leap59ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.248.14.2.3.41.1.19 |
hmNetPTP2Leap61ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.248.14.2.3.41.1.20 |
hmNetPTP2TimeTraceablerw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.248.14.2.3.41.1.21 |
hmNetPTP2FrequencyTraceablerw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.248.14.2.3.41.1.22 |
hmNetPTP2PtpTimescalerw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.248.14.2.3.41.1.23 |
hmNetPTP2TimeSourcerw Enumeration .1.3.6.1.4.1.248.14.2.3.41.1.24 |
hmNetPTP2GrandmasterClockClassro Integer32 .1.3.6.1.4.1.248.14.2.3.41.1.25 |
hmNetPTP2GrandmasterClockAccuracyro Enumeration .1.3.6.1.4.1.248.14.2.3.41.1.26 |
hmNetPTP2GrandmasterClockVariancero Integer32 .1.3.6.1.4.1.248.14.2.3.41.1.27 |
hmNetPTP2PortTableThis table contains variables for each PTP2 port of
the switch. SEQUENCE OF HmNetPTP2PortEntry .1.3.6.1.4.1.248.14.2.3.41.2 |
hmNetPTP2PortEntryEntry for one port. HmNetPTP2PortEntry .1.3.6.1.4.1.248.14.2.3.41.2.1 |
hmNetPTP2PortEnablerw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.248.14.2.3.41.2.1.1 |
hmNetPTP2PortStateState of the PTP2 port intance.ro Enumeration .1.3.6.1.4.1.248.14.2.3.41.2.1.2 |
hmNetPTP2LogDelayReqIntervalro Integer32 .1.3.6.1.4.1.248.14.2.3.41.2.1.3 |
hmNetPTP2PeerMeanPathDelayro PTPTimeInterval .1.3.6.1.4.1.248.14.2.3.41.2.1.4 |
hmNetPTP2LogAnnounceIntervalrw Enumeration .1.3.6.1.4.1.248.14.2.3.41.2.1.5 |
hmNetPTP2AnnounceReceiptTimeoutrw INTEGER .1.3.6.1.4.1.248.14.2.3.41.2.1.6 |
hmNetPTP2LogSyncIntervalrw Enumeration .1.3.6.1.4.1.248.14.2.3.41.2.1.7 |
hmNetPTP2DelayMechanismrw Enumeration .1.3.6.1.4.1.248.14.2.3.41.2.1.8 |
hmNetPTP2LogPdelayReqIntervalrw Enumeration .1.3.6.1.4.1.248.14.2.3.41.2.1.9 |
hmNetPTP2VersionNumberrw Enumeration .1.3.6.1.4.1.248.14.2.3.41.2.1.10 |
hmNetPTP2NetworkProtocolrw Enumeration .1.3.6.1.4.1.248.14.2.3.41.2.1.11 |
hmNetPTP2V1Compatibilityrw Enumeration .1.3.6.1.4.1.248.14.2.3.41.2.1.12 |
hmNetPTP2DelayAsymmetryrw PTPTimeInterval .1.3.6.1.4.1.248.14.2.3.41.2.1.13 |
hmNetPTP2PortCapabilityThis object shows the capability of the ptp port.ro Bits .1.3.6.1.4.1.248.14.2.3.41.2.1.14 |
hmNetPTP2VlanIDVLAN in which PTP packets are send. With a value of -1 all packets are send untaggedrw Integer32(-1..4042) .1.3.6.1.4.1.248.14.2.3.41.2.1.15 |
hmNetPTP2VlanPriorityVLAN priority of tagged ptp packetsrw Integer32 .1.3.6.1.4.1.248.14.2.3.41.2.1.16 |
hmNetPTP2TCGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.2.3.42 |
hmNetPTP2TCConfiguration OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.2.3.42.1 |
hmNetPTP2TCClockIdentityro PTPClockIdentity .1.3.6.1.4.1.248.14.2.3.42.1.1 |
hmNetPTP2TCDelayMechanismrw Enumeration .1.3.6.1.4.1.248.14.2.3.42.1.2 |
hmNetPTP2TCPrimaryDomainrw Integer32 .1.3.6.1.4.1.248.14.2.3.42.1.3 |
hmNetPTP2TCSyntonizedrw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.248.14.2.3.42.1.4 |
hmNetPTP2TCNetworkProtocolrw Enumeration .1.3.6.1.4.1.248.14.2.3.42.1.5 |
hmNetPTP2TCCurrentMasterro PTPPortIdentity .1.3.6.1.4.1.248.14.2.3.42.1.6 |
hmNetPTP2TCManagementrw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.248.14.2.3.42.1.7 |
hmNetPTP2TCMultiDomainModerw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.248.14.2.3.42.1.8 |
hmNetPTP2TCSyncLocalClockEnable synchronisation of the local clock. This is only valid if syntonization is enabledrw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.248.14.2.3.42.1.9 |
hmNetPTP2TCVlanIDVLAN in which PTP packets are send. With a value of -1 all packets are send untaggedrw Integer32(-1..4042) .1.3.6.1.4.1.248.14.2.3.42.1.10 |
hmNetPTP2TCVlanPriorityVLAN priority of tagged ptp packetsrw Integer32 .1.3.6.1.4.1.248.14.2.3.42.1.11 |
hmNetPTP2TCPortTableThis table contains variables for each PTP2 TC port of
the switch. SEQUENCE OF HmNetPTP2TCPortEntry .1.3.6.1.4.1.248.14.2.3.42.2 |
hmNetPTP2TCPortEntryEntry for one port. HmNetPTP2TCPortEntry .1.3.6.1.4.1.248.14.2.3.42.2.1 |
hmNetPTP2TCPortEnablerw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.248.14.2.3.42.2.1.1 |
hmNetPTP2TCLogPdelayReqIntervalrw Enumeration .1.3.6.1.4.1.248.14.2.3.42.2.1.2 |
hmNetPTP2TCFaultyro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.248.14.2.3.42.2.1.3 |
hmNetPTP2TCPeerMeanPathDelayro PTPTimeInterval .1.3.6.1.4.1.248.14.2.3.42.2.1.4 |
hmNetPTP2TCDelayAsymmetryrw PTPTimeInterval .1.3.6.1.4.1.248.14.2.3.42.2.1.5 |
hmNetSNMPGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.2.3.50 |
hmNetSNMPv1StatusEnables/disables the SNMP Version 1 protocol.rw Enumeration .1.3.6.1.4.1.248.14.2.3.50.1 |
hmNetSNMPv2StatusEnables/disables the SNMP Version 2 protocol.rw Enumeration .1.3.6.1.4.1.248.14.2.3.50.2 |
hmNetSNMPv3StatusEnables/disables the SNMP Version 3 protocol.rw Enumeration .1.3.6.1.4.1.248.14.2.3.50.3 |
hmNetSNMPAccessStatusEnables/disables the SNMP protocol access
on this device.
If only read access is allowed set this object
to readOnly(3).rw Enumeration .1.3.6.1.4.1.248.14.2.3.50.4 |
hmNetSNMPSynchronizeV1V3StatusEnables/disables the synchronization between
the SNMPv1 community and the SNMPv3 password.
If enabled the first read-write community in hmAuthCommTable
is used for the SNMPv3 admin password.
This is the same password that is used in the user- and
webinterface.
Further, if enabled the first read-only community in
hmAuthCommTable is used for the SNMPv3 user password.rw Enumeration .1.3.6.1.4.1.248.14.2.3.50.5 |
hmNetSNMPPortNumberThe port number of the snmp server.
To activate the port number the device
has to be restarted.rw Integer32 .1.3.6.1.4.1.248.14.2.3.50.6 |
hmNetSNMPRadiusAuthenticateEnables/disables authentication of SNMPv3
users via RADIUS serverrw Enumeration .1.3.6.1.4.1.248.14.2.3.50.7 |
hmNetSNMPv3EncryptionReadWriteStatusEnables/disables the SNMPv3 admin Data Encryption.rw Enumeration .1.3.6.1.4.1.248.14.2.3.50.8 |
hmNetSNMPv3EncryptionReadOnlyStatusEnables/disables the SNMPv3 user Data Encryption.rw Enumeration .1.3.6.1.4.1.248.14.2.3.50.9 |
hmNetGPSGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.2.3.60 |
hmNetGPSIsAvailableIndicates if a GPS module is available.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.248.14.2.3.60.1 |
hmNetGPSIsSynchronizedIndicates if the GPS module is synchronized to the GPS signal.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.248.14.2.3.60.2 |
hmNetGPSModeShows the mode of the GPS module. If hmNetGPSMode is gpsIn(1), the GPS
module reads the signal from a GPS receiver in the format given in
hmNetGPSTimeStringFormat. If the mode is gpsOut(2), the GPS module
sends out a signal in the format given in hmNetGPSTimeStringFormat.rw Enumeration .1.3.6.1.4.1.248.14.2.3.60.3 |
hmNetGPSTimeStringFormatThese are the GPS time string formats which a GPS module can read or write.rw Enumeration .1.3.6.1.4.1.248.14.2.3.60.4 |
hmRestrictedMgtAccessGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.2.3.70 |
hmRMAOperationEnables/disables Management Access globallyrw Enumeration .1.3.6.1.4.1.248.14.2.3.70.1 |
hmRMATableA list of Management Access Entries (Rules) to increase security SEQUENCE OF HmRMAEntry .1.3.6.1.4.1.248.14.2.3.70.2 |
hmRMAEntryAn entry contains a rule for the Management Access. HmRMAEntry .1.3.6.1.4.1.248.14.2.3.70.2.1 |
hmRMAIndexThe unique index used for each row in the RMA Tablero INTEGER .1.3.6.1.4.1.248.14.2.3.70.2.1.1 |
hmRMARowStatusDescribes the status of a row in this table if it is active or not available ...rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.248.14.2.3.70.2.1.2 |
hmRMAIpAddrAllowed IP addressrw IpAddress .1.3.6.1.4.1.248.14.2.3.70.2.1.3 |
hmRMANetMaskNetwork Maskrw IpAddress .1.3.6.1.4.1.248.14.2.3.70.2.1.4 |
hmRMASrvHttpEnables/disables HHTP accessrw Enumeration .1.3.6.1.4.1.248.14.2.3.70.2.1.5 |
hmRMASrvSnmpEnables/disbales SNMP accessrw Enumeration .1.3.6.1.4.1.248.14.2.3.70.2.1.6 |
hmRMASrvTelnetEnables/disables Telnet accessrw Enumeration .1.3.6.1.4.1.248.14.2.3.70.2.1.7 |
hmRMASrvSshEnables/disables SSH accessrw Enumeration .1.3.6.1.4.1.248.14.2.3.70.2.1.8 |
hmFSTable OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.2.4 |
hmFSUpdFileNameFull specified filename of the update file
e.g. tftp://192.9.200.1/upd/bootrom.v3 .rw DisplayString .1.3.6.1.4.1.248.14.2.4.1 |
hmFSConfFileNameFull specified name of the configuration file
e.g. tftp://192.9.200.1/cfg/config1.sav .rw DisplayString .1.3.6.1.4.1.248.14.2.4.2 |
hmFSLogFileNameLocal or full specified url of the log file.
If value is local, the log will be written to the flash.
e.g. tftp://192.9.200.1/log/log300599.log or local.rw DisplayString .1.3.6.1.4.1.248.14.2.4.3 |
hmFSUserNamelogin name for the used file transport protocol.rw DisplayString .1.3.6.1.4.1.248.14.2.4.4 |
hmFSTPPasswordpassword for the used file transport protocol.rw DisplayString .1.3.6.1.4.1.248.14.2.4.5 |
hmFSActionThis object, when read, always returns a value of other (1).
When set to update (2), the updatefile specified by
hmFSUpdFileName will be loaded. config-load (3) will load the
configuration stored in the local flash. config-save (4) will
write the present configuration to the flash.
config-load-remote (5) will load the configuration stored in
a file specified by hmFSConfigFileName (which may be in binary
or script format).
config-save-remote (6) will save the present configuration in a
file specified by hmFSConfigFileName.
log-save (7) will save the local logfile to a file specified
with hmFSLogFileName. config-load-default (8) will restore the
default settings and set-to-factory (9) will apply the factory
settings to the system and save the configuration to flash.
log-clear (10) will clear the logfile of the agent.
gbl-update (12) will perform a software update of the whole chassis.
config-load-backup (13) loads an automatically saved backup configuration
config-remote-and-save (15) loads a configuration via tftp and saves it
to the flash. toggleImage (20) switches between main and backup
software image to be active (so it will be loaded after the next coldstart).
config-save-remote-script (21) saves the current configuration in script
format to the file specified by hmFSConfigFileName.
Any other value results in a badValue status code.rw Enumeration .1.3.6.1.4.1.248.14.2.4.6 |
hmFSActionResultResult of the last activated action.ro Enumeration .1.3.6.1.4.1.248.14.2.4.8 |
hmFSBootConfigurationBy setting this MIB variable the user can control which
configuration should be read during system initialization:
default(1) : boot with factory settings
local(2) : boot with locally stored configurationrw Enumeration .1.3.6.1.4.1.248.14.2.4.9 |
hmFSRunningConfigurationBy setting this MIB variable the user can control which
configuration should be read after switch initialization:
boot(1) : the one which is selected
by hmFSBootConfiguration
local(2) : boot with locally stored configuration
remote(3) : use the remotely stored configuration
according to hmFSConfFileNamerw Enumeration .1.3.6.1.4.1.248.14.2.4.10 |
hmFSLastMessageerror message of the last hmFSAction performed. If there was no error
encountered, the value of this variable will be 'OK'ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.248.14.2.4.11 |
hmConfigurationStatusStatus of the local configuration.
ok(1): Local and running configuration match.
notInSync(2): Local and running configuration don't match,
configuration has not yet been saved.ro Enumeration .1.3.6.1.4.1.248.14.2.4.12 |
hmFSFileTablea directory of the internal file system SEQUENCE OF HmFSFileEntry .1.3.6.1.4.1.248.14.2.4.100 |
hmFSFileEntryThe entry of the hmFSFileTable. HmFSFileEntry .1.3.6.1.4.1.248.14.2.4.100.1 |
hmFSFileIDThis index is used to identify the associated filero Integer32 .1.3.6.1.4.1.248.14.2.4.100.1.1 |
hmFSFileNamefile name excluding pathro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.248.14.2.4.100.1.2 |
hmFSFileSizefile size in bytesro Integer32 .1.3.6.1.4.1.248.14.2.4.100.1.3 |
hmFSFileDatedate in UNIX format (seconds since 1 jan 1970)ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.248.14.2.4.100.1.4 |
hmAutoconfigGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.2.4.200 |
hmAutoconfigAdapterStatusStatus of the AutoConfiguration Adapter.
notPresent(1): AutoConfiguration Adapter has not been detected.
removed(2): Configuration was loaded from adapter, but adapter
was removed in running mode of the agent.
ok(3): Configuration of adapter and switch match.
notInSync(4): Configuration of adapter and switch don't match,
e.g. configuration has not yet been written into
the adapter.
outOfMemory(5): Configuration is too large for the adapter.
wrongMachine(6): Adapter contains configuration which cannot
be loaded into this machine because it was
created by a different type of switch.
checksumErr(7): Data in adapter fails consistency check.
genericErr(8): Any other failure, e.g. hardware malfunction.
autodisabled(9): USB port has been disabled for safety reasons.ro Enumeration .1.3.6.1.4.1.248.14.2.4.200.1 |
hmAutoconfigAdapterSerialNumThe serial number provided by vendor (ASCII).ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.248.14.2.4.200.2 |
hmConfigWatchdogGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.2.4.201 |
hmConfigWatchdogAdminStatusAdministrative status of the configuration watchdog.
enable(1): start/trigger the watchdog timer
disable(2): turn off the watchdog
This feature provides recovery from situations where the
switch cannot be reached by the management station anymore.
Whenever this variable is set to enable(1), the value of
hmConfigWatchdogTimeInterval is loaded into the watchdog timer.
This timer must be triggered before hmConfigWatchdogTimerValue
reaches 0. If the watchdog timer expires, the last saved
configuration of the switch will be restored.
The watchdog is triggered with MIB read and write accessesrw Enumeration .1.3.6.1.4.1.248.14.2.4.201.1 |
hmConfigWatchdogOperStatusOperational status of the configuration watchdog.
enable(1): watchdog up and running
disable(2): watchdog inactivero Enumeration .1.3.6.1.4.1.248.14.2.4.201.2 |
hmConfigWatchdogTimeIntervalPeriod of the watchdog timer in seconds.rw Integer32 .1.3.6.1.4.1.248.14.2.4.201.3 |
hmConfigWatchdogTimerValueCurrent count-down value of the watchdog timer in seconds.ro Integer32 .1.3.6.1.4.1.248.14.2.4.201.4 |
hmConfigWatchdogIPAddressCurrent IP Adress of station that triggers the watchdog.ro IpAddress .1.3.6.1.4.1.248.14.2.4.201.5 |
hmTempTable OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.2.5 |
hmTemperatureThis signed integer is used to identify the temperature
within the agent in units of centigrade (celsius).ro Integer32 .1.3.6.1.4.1.248.14.2.5.1 |
hmTempUprLimitThis value is used to define a maximum level for the
temperature within an agent. If the temperature rises above
this upper limit, the management station will be notified by
a hmTemperature trap.rw Integer32 (-99..99) .1.3.6.1.4.1.248.14.2.5.2 |
hmTempLwrLimitThis value is used to define a minimum level for the
temperature within a concentrator. If the temperature falls
below this lower limit, the management station will be notified
by a hmTemperature trap.rw Integer32 (-99..99) .1.3.6.1.4.1.248.14.2.5.3 |
hmNeighbourAgentTableA list of the neighbour agents in a chassis SEQUENCE OF HmNeighbourAgentEntry .1.3.6.1.4.1.248.14.2.6 |
hmNeighbourAgentEntryThe entry of the hmNeighbourAgentTable. HmNeighbourAgentEntry .1.3.6.1.4.1.248.14.2.6.1 |
hmNeighbourSlotAn index that uniquely identifies an agent by the
slot in the chassis.ro Integer32 .1.3.6.1.4.1.248.14.2.6.1.1 |
hmNeighbourIpAddressThe IP Address of the agent.ro IpAddress .1.3.6.1.4.1.248.14.2.6.1.2 |
hmAuthGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.2.7 |
hmAuthHostTableEntriesMaxThe maximum possible number of entries in the hmAuthHostTable.
This value equates to the total number of trusted Hosts which
potentially may be recognized.ro Integer32 .1.3.6.1.4.1.248.14.2.7.1 |
hmAuthCommTableEntriesMaxThe maximum possible number of entries in the hmAuthCommTable.
This value equates to the total number of communities which
ly may be recognized.ro Integer32 .1.3.6.1.4.1.248.14.2.7.2 |
hmAuthCommTableA list of valid SNMP Community Entries. SEQUENCE OF HmAuthCommEntry .1.3.6.1.4.1.248.14.2.7.3 |
hmAuthCommEntryA list of SNMP Community properties. HmAuthCommEntry .1.3.6.1.4.1.248.14.2.7.3.1 |
hmAuthCommIndexAn index that uniquely identifies an ordered entry in the
SNMP Community Table.ro Integer32 .1.3.6.1.4.1.248.14.2.7.3.1.1 |
hmAuthCommNameThe name of this SNMP Community Entry, e.g. public.
This object can only be written.rw DisplayString .1.3.6.1.4.1.248.14.2.7.3.1.2 |
hmAuthCommPermThe Read/Write (GET/SET) permission for the community. A (1)
indicates perm-ro (GET) permission. A (2) indicates perm-wr
(GET/SET) permission.rw Enumeration .1.3.6.1.4.1.248.14.2.7.3.1.3 |
hmAuthCommStateThe state of this community entry. Enable (1) defines an entry
that is valid. Disable (2) defines an entry that is valid but
not enabled. Delete (3) removes an entry from the table.
Invalid (4) defines an entry that is no longer valid (e.g., an
entry that was deleted) and should be ignored. An attempt to set
a value of invalid (4) causes the agent to return SNMP_BADVALUE.rw Enumeration .1.3.6.1.4.1.248.14.2.7.3.1.4 |
hmAuthHostTableA list of valid SNMP Trusted Host Entries. SEQUENCE OF HmAuthHostEntry .1.3.6.1.4.1.248.14.2.7.4 |
hmAuthHostEntryA list of SNMP Host properties. HmAuthHostEntry .1.3.6.1.4.1.248.14.2.7.4.1 |
hmAuthHostIndexAn index that uniquely identifies an ordered entry in
the SNMP Trusted Host Table.ro Integer32 .1.3.6.1.4.1.248.14.2.7.4.1.1 |
hmAuthHostNameThe name of this SNMP Trusted Host Entry, e.g. host1.rw DisplayString .1.3.6.1.4.1.248.14.2.7.4.1.2 |
hmAuthHostCommIndexThe index of this SNMP Trusted Host Entry's community entry in
the hmAuthCommTable.rw Integer32 .1.3.6.1.4.1.248.14.2.7.4.1.3 |
hmAuthHostIpAddressThe IP Address for the host. This identified host has
permission to access information in this device's MIB tables,
providing the SNMP security toggle is on (see hmMiscSNMPSecurity).rw IpAddress .1.3.6.1.4.1.248.14.2.7.4.1.4 |
hmAuthHostIpMaskThe Network Mask for the trusted Host entry.rw IpAddress .1.3.6.1.4.1.248.14.2.7.4.1.5 |
hmAuthHostStateThe state of this trusted host entry. Enable (1) defines an
entry that is valid. Disable (2) defines an entry that is
valid but not enabled. Delete (3) removes an entry from the
table. Invalid (4) defines an entry that is no longer valid
(e.g., an entry that was deleted) and should be ignored. An
attempt to set a value of invalid (4) causes the agent to
return SNMP_BADVALUE.rw Enumeration .1.3.6.1.4.1.248.14.2.7.4.1.6 |
hmTrapGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.2.8 |
hmTrapCommTableEntriesMaxThe total number of entries in the hmTrapCommTable. This value
equates to the total number of communities which potentially can
be recognized.ro Integer32 .1.3.6.1.4.1.248.14.2.8.1 |
hmTrapDestTableEntriesMaxThe total number of entries in the hmTrapDestTable. This
equates to the total number of hosts which can potentially
be sent SNMP traps.ro Integer32 .1.3.6.1.4.1.248.14.2.8.2 |
hmTrapCommTableA list of valid SNMP Community Entries used for Traps. SEQUENCE OF HmTrapCommEntry .1.3.6.1.4.1.248.14.2.8.3 |
hmTrapCommEntryA list of SNMP Trap Community properties. HmTrapCommEntry .1.3.6.1.4.1.248.14.2.8.3.1 |
hmTrapCommIndexAn index that uniquely identifies an ordered entry in
the SNMP Community Trap Table.ro Integer32 .1.3.6.1.4.1.248.14.2.8.3.1.1 |
hmTrapCommCommIndexThe communities entry index of this SNMP Trap Community Entry.rw Integer32 .1.3.6.1.4.1.248.14.2.8.3.1.2 |
hmTrapCommColdStartEnable (1) or Disable (2) the SNMP ColdStart Trap for this
SNMP community.rw Enumeration .1.3.6.1.4.1.248.14.2.8.3.1.3 |
hmTrapCommLinkDownEnable (1) or Disable (2) the SNMP Link Down traps for this
SNMP community.rw Enumeration .1.3.6.1.4.1.248.14.2.8.3.1.4 |
hmTrapCommLinkUpEnable (1) or Disable (2) the SNMP Link Up traps for this
SNMP community.rw Enumeration .1.3.6.1.4.1.248.14.2.8.3.1.5 |
hmTrapCommAuthenticationEnable (1) or Disable (2) the SNMP Authentication traps for
this SNMP community.rw Enumeration .1.3.6.1.4.1.248.14.2.8.3.1.6 |
hmTrapCommBridgeEnable (1) or Disable (2) the SNMP Bridge MIB traps for this
SNMP community.
Available Traps:
newRoot (MACH)
topologyChange (MACH)rw Enumeration .1.3.6.1.4.1.248.14.2.8.3.1.7 |
hmTrapCommRMONEnable (1) or Disable (2) the SNMP RMON traps for this SNMP
community.
Available Traps:
risingAlarm (MACH, MICE, RS2)
fallingAlarm (MACH, MICE, RS2)rw Enumeration .1.3.6.1.4.1.248.14.2.8.3.1.8 |
hmTrapCommUsergroupEnable (1) or Disable (2) the SNMP Enterprise usergroup traps
for this SNMP community.
Available Traps:
hmNewUserTrap (MACH)
hmPortSecurityTrap (MACH, MICE, RS2)
hmPortSecConfigErrorTrap (MACH)rw Enumeration .1.3.6.1.4.1.248.14.2.8.3.1.9 |
hmTrapCommDualHomingEnable (1) or Disable (2) the SNMP Enterprise dual homing traps
for this SNMP community.
Available Traps:
hmDuHmReconfig (MACH)
hmDuHmRedundancy (MACH)
hmRingRedReconfig (MACH, MICE)rw Enumeration .1.3.6.1.4.1.248.14.2.8.3.1.10 |
hmTrapCommChassisEnable (1) or Disable (2) the SNMP Enterprise chassis traps
for this SNMP community.
Available Traps:
hmGroupMapChange (MACH)
hmPowerSupply (MACH, MICE, RS2)
hmFan (MACH)
hmSignallingRelay (MICE, RS2)
hmStandby (MACH, MICE, RS2)
hmSelfTestError (MACH)
hmModuleMapChange (MICE)
hmTemperature (MACH)
hmLoginTrap (MACH)
hmDuplicateStaticAddressTrap (MACH)rw Enumeration .1.3.6.1.4.1.248.14.2.8.3.1.11 |
hmTrapCommStateThe state of this community entry. Enable (1) defines an entry
that is valid. Disable (2) defines an entry that is valid but
not enabled. Delete (3) removes an entry from the table.
Invalid (4) defines an entry that is no longer valid (e.g.,
an entry that was deleted) and should be ignored. An attempt
to set a value of invalid (4) causes the agent to return
SNMP_BADVALUE.rw Enumeration .1.3.6.1.4.1.248.14.2.8.3.1.12 |
hmTrapDestTableA list of valid SNMP Trap Trusted Host Destination entries. SEQUENCE OF HmTrapDestEntry .1.3.6.1.4.1.248.14.2.8.4 |
hmTrapDestEntryA list of SNMP Trap Trusted Host Destination properties. HmTrapDestEntry .1.3.6.1.4.1.248.14.2.8.4.1 |
hmTrapDestIndexAn index that uniquely identifies an ordered entry in
the SNMP Trusted Host Destination Table.ro Integer32 .1.3.6.1.4.1.248.14.2.8.4.1.1 |
hmTrapDestNameThe name of this SNMP Trusted Host Destination Entry, e.g. Admin.rw DisplayString .1.3.6.1.4.1.248.14.2.8.4.1.2 |
hmTrapDestCommIndexThe communities entry index of this SNMP Trusted Host
Destination Entry's community.rw Integer32 .1.3.6.1.4.1.248.14.2.8.4.1.3 |
hmTrapDestIpAddressThe IP Address for the host. This identified host has permission
to access information in this device's MIB tables, providing the
SNMP security toggle is on (see hmMiscSNMPSecurity).rw IpAddress .1.3.6.1.4.1.248.14.2.8.4.1.4 |
hmTrapDestIpMaskThe Network Mask for the trusted Host Destination entry.rwobsolete IpAddress .1.3.6.1.4.1.248.14.2.8.4.1.5 |
hmTrapDestStateThe state of this trusted trap destination entry. Enable (1)
defines an entry that is valid. Disable (2) defines an entry
that is valid but not enabled. Delete (3) removes an entry
from the table. Invalid (4) defines an entry that is no
longer valid (e.g., an entry that was deleted) and should be
ignored. An attempt to set a value of invalid (4) causes the
agent to return SNMP_BADVALUE.rw Enumeration .1.3.6.1.4.1.248.14.2.8.4.1.6 |
hmLastAccessGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.2.9 |
hmLastIpAddrIP Address specified in the last request.ro IpAddress .1.3.6.1.4.1.248.14.2.9.1 |
hmLastPortUDP port specified in the last request.ro Integer32 .1.3.6.1.4.1.248.14.2.9.2 |
hmLastCommunityLast community string used.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.248.14.2.9.3 |
hmLastLoginUserNameLast login user name used.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.248.14.2.9.4 |
hmMulticast OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.2.10 |
hmIGMPGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.2.10.1 |
hmIGMPSnoop OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.2.10.1.2 |
hmIGMPSnoopStatusEnables/disables IGMP Snooping on this device.
The default value is disable.rw Enumeration .1.3.6.1.4.1.248.14.2.10.1.2.1 |
hmIGMPSnoopAgingTimeThe timeout period in seconds for aging out Multicast Groups
dynamically learned with IGMP Snooping. Note that aging operates
on a per interface per multicast group basis.
This interval is also used to age out ports that have received
IGMP Router Query PDUs.
The default is 260 seconds and the range is 3 to 3600 seconds.rw Integer32 .1.3.6.1.4.1.248.14.2.10.1.2.2 |
hmIGMPSnoopUnknownModeSets the mode how unknown Multicast packets
will be treated.
The default value is flood(2).rw Enumeration .1.3.6.1.4.1.248.14.2.10.1.2.3 |
hmIGMPSnoopUnknownAgingTimeThe timeout period in seconds approximately for aging out Unknown Multicast Groups
dynamically learned with traffic snooping. The exactly value is
UnknownLookupInterval/(UnknownLookupInterval-UnknownLookupResponseTime)*UnknownAgingTime.
Note that aging operates on a per unknown multicast group basis.
The default is 260 seconds and the range is 3 to 3600 seconds.rw Integer32 .1.3.6.1.4.1.248.14.2.10.1.2.4 |
hmIGMPSnoopUnknownLookupIntervalThe frequency at which Unknown Multicast Groups
dynamically learned with traffic snooping are
traffic checked by the switch in seconds.
So this is the time between periodic traffic checking
in which unknown multicast groups being aged on the switch
when it is acting as Trafficsnooper.
Large values lead to traffic checking less often.
The default is 125 seconds and the range is 2 to 3599 seconds.rw Integer32 .1.3.6.1.4.1.248.14.2.10.1.2.5 |
hmIGMPSnoopUnknownLookupResponseTimeThe unknown lookup response time in seconds in which Unknown Multicast Groups
dynamically learned with traffic snooping are traffic checked.
So this is the time in which response traffic to the Trafficsnooper allowing
the update of unknown multicast group aging timer.
This variable enables the checking of bursty unknown multicast traffic.
Small values lead to bad traffic checking but few snooper load and
large values lead to good traffic checking but more snooper load.
The default is 10 seconds and the range is 1 to 3598 seconds.rw Integer32 .1.3.6.1.4.1.248.14.2.10.1.2.6 |
hmIGMPSnoopQuerierToPortmaskEnables or disables the addition of query ports
to multicast filter portmasks.rw Enumeration .1.3.6.1.4.1.248.14.2.10.1.2.7 |
hmIGMPSnoopQuerierIPAddressShows the IP address of the active querier.ro IpAddress .1.3.6.1.4.1.248.14.2.10.1.2.8 |
hmIGMPSnoopQueryTableA table displaying the IGMP Router Query PDU ports. SEQUENCE OF HmIGMPSnoopQueryEntry .1.3.6.1.4.1.248.14.2.10.1.2.10 |
hmIGMPSnoopQueryEntryA table displaying the IGMP Router Query PDU ports.
These are maintained on a per VLAN basis. HmIGMPSnoopQueryEntry .1.3.6.1.4.1.248.14.2.10.1.2.10.1 |
hmIGMPSnoopQueryVlanIndexThis is the VLAN index for which this entry is valid.
If the switch only supports shared vlan learning (SVL),
the value is always 1 and there is only 1 instance in
the table. Integer32 .1.3.6.1.4.1.248.14.2.10.1.2.10.1.1 |
hmIGMPSnoopQueryPortsThis read-only object displays the set of ports that have received
IGMP Router Query PDUs for this VLAN as determined by the IGMP
Snooping task.ro OCTET STRING .1.3.6.1.4.1.248.14.2.10.1.2.10.1.2 |
hmIGMPSnoopFilterTableA table containing the multicast filtering information
on a per vlan basis learned with IGMP Snooping. SEQUENCE OF HmIGMPSnoopFilterEntry .1.3.6.1.4.1.248.14.2.10.1.2.11 |
hmIGMPSnoopFilterEntryThe entry of the hmIGMPSnoopFilterTable. HmIGMPSnoopFilterEntry .1.3.6.1.4.1.248.14.2.10.1.2.11.1 |
hmIGMPSnoopFilterVlanIndexThis is the VLAN index for which this entry is valid.
If the switch only supports shared vlan learning (SVL),
the value is always 1 and there is only 1 instance in
the table. Integer32 .1.3.6.1.4.1.248.14.2.10.1.2.11.1.1 |
hmIGMPSnoopFilterAddressThe multicast destination MAC address in a frame to which
this entry's filtering information applies. MacAddress (SNMPv2-TC) .1.3.6.1.4.1.248.14.2.10.1.2.11.1.2 |
hmIGMPSnoopFilterLearntPortsThe set of ports, to which frames destined for this Group
MAC Address learned by IGMP Snooping are currently being
forwarded.
Each octet within the value of this object specifies
a set of eight ports, with the first octet specifying
ports 1 through 8, the second octet specifying ports 9
through 16, etc.
Within each octet, the most significant bit represents
the lowest numbered port, and the least significant bit
represents the highest numbered port.
Thus, each port of the bridge is represented by a single
bit within the value of this object.
If that bit has a value of '1' then that port is included
in the set of ports; the port is not included if its bit
has a value of '0'.
(Note that the setting of the bit corresponding to the port
from which a frame is received is irrelevant.)ro OCTET STRING .1.3.6.1.4.1.248.14.2.10.1.2.11.1.3 |
hmIGMPSnoopForwardAllTableA table containing forwarding information for each
VLAN, specifying the set of ports to which forwarding of
all multicasts applies, configured statically by
management.
An entry appears in this table for all VLANs that are currently
instantiated. SEQUENCE OF HmIGMPSnoopForwardAllEntry .1.3.6.1.4.1.248.14.2.10.1.2.12 |
hmIGMPSnoopForwardAllEntryForwarding information for a VLAN, specifying the set
of ports to which all multicasts should be forwarded,
configured statically by management. HmIGMPSnoopForwardAllEntry .1.3.6.1.4.1.248.14.2.10.1.2.12.1 |
hmIGMPSnoopForwardAllVlanIndexThis is the VLAN index for which this entry is valid.
If the switch only supports shared vlan learning (SVL),
the value is always 1 and there is only 1 instance in
the table. Integer32 .1.3.6.1.4.1.248.14.2.10.1.2.12.1.1 |
hmIGMPSnoopForwardAllStaticPortsThe set of ports configured by management in this VLAN
to which all multicast group-addressed frames learned by
IGMP are to be forwarded.
This value will be restored after the device is reset.rw OCTET STRING .1.3.6.1.4.1.248.14.2.10.1.2.12.1.2 |
hmIGMPSnoopQueryStaticTableA table displaying the IGMP Static Query ports. SEQUENCE OF HmIGMPSnoopQueryStaticEntry .1.3.6.1.4.1.248.14.2.10.1.2.13 |
hmIGMPSnoopQueryStaticEntryThe entry of the hmIGMPSnoopQueryStaticTable. HmIGMPSnoopQueryStaticEntry .1.3.6.1.4.1.248.14.2.10.1.2.13.1 |
hmIGMPSnoopQueryStaticVlanIndexThis is the VLAN index for which this entry is valid.
If the switch only supports shared vlan learning (SVL),
the value is always 1 and there is only 1 instance in
the table. Integer32 .1.3.6.1.4.1.248.14.2.10.1.2.13.1.1 |
hmIGMPSnoopQueryStaticPortsThe set of ports explicitly configured by management to
be IGMP-forwarding ports.rw OCTET STRING .1.3.6.1.4.1.248.14.2.10.1.2.13.1.2 |
hmIGMPSnoopQueryStaticAutomaticPortsThe set of ports that are automatically learned by LLDP protocol to
be IGMP-forwarding ports.ro OCTET STRING .1.3.6.1.4.1.248.14.2.10.1.2.13.1.3 |
hmIGMPSnoopQueryStaticAutomaticPortsEnableThe set of ports that are allowed to be learned automatically by LLDP protocol to
be IGMP-forwarding ports.rw OCTET STRING .1.3.6.1.4.1.248.14.2.10.1.2.13.1.4 |
hmIGMPQuerierGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.2.10.1.2.100 |
hmIGMPQuerierStatusEnables/disables IGMP Querier on this device.
IGMP queries are only sent when hmIGMPSnoopStatus is also set.
The default value is disable.rw Enumeration .1.3.6.1.4.1.248.14.2.10.1.2.100.1 |
hmIGMPQuerierModeShows the current mode of the IGMP Querier.ro Enumeration .1.3.6.1.4.1.248.14.2.10.1.2.100.2 |
hmIGMPQuerierTransmitIntervalThe frequency at which IGMP general query packets are
transmitted by the querying switch in seconds.
So this is the time between general periodic queries being
sent out of the switch when it is acting as the IGMP querier.
Large values lead to IGMP queries being sent less often.
The default is 125 seconds and the range is 2 to 3599 seconds.rw Integer32 .1.3.6.1.4.1.248.14.2.10.1.2.100.3 |
hmIGMPQuerierMaxResponseTimeThe maximum query response time in seconds advertised in IGMP v2
queries on this VLAN if the switch is the querier. Smaller values
allow a switch to prune groups faster. So it is the maximum response
time inserted into the general periodic queries. This variable
enables the tuning of the burstiness of the IGMP traffic.
If it is increased the responses have a larger time span in which
to be generated by the hosts.
The default is 10 seconds and the range is 1 to 3598 seconds.rw Integer32 .1.3.6.1.4.1.248.14.2.10.1.2.100.4 |
hmIGMPQuerierProtocolVersionThe Querier protocol version.
The default is version 2.rw Integer32 .1.3.6.1.4.1.248.14.2.10.1.2.100.5 |
hmGMRPGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.2.10.2 |
hmGMRP OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.2.10.2.1 |
hmGmrpUnknownModeSets the mode how unknown multicast packets will be treated.
The default value is flood(2).rw Enumeration .1.3.6.1.4.1.248.14.2.10.2.1.1 |
hmRelayGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.2.11 |
hmRelayOption82StatusEnables/disables the DHCP Option 82 defined in RFC 3046
on this device.rw Enumeration .1.3.6.1.4.1.248.14.2.11.1 |
hmRelayOptionRemoteIDTypeThis option determines the content of the Agent Remote ID (sub-option 2).
ip(1) inserts the ip address of the relay's mgmt-interface
and encodes it with sub option type A1.
mac(2) inserts the mac adress of the relay's mgmt-interface
and encodes it with sub option type 00.
client-id(3) inserts the client identifier (sysName) of the relay's mgmt-interface
and encodes it with sub option type A2.
other(4) inserts the value in hmRelayOptionRemoteIDValue
and encodes it with sub option type A3.rw Enumeration .1.3.6.1.4.1.248.14.2.11.2 |
hmRelayOptionRemoteIDDisplays the actual content of the Remote ID sub option for this relay agent.
The value is encoded in TLV (Type-Length-Value) format.
The following type values are currently defined:
00 = mac adress
A1 = ip address
A2 = client identifier
A3 = string in hmRelayOptionRemoteIDValuero OCTET STRING .1.3.6.1.4.1.248.14.2.11.3 |
hmRelayOptionRemoteIDValueContains an octet string to be used as value for
Agent Remote ID Sub-option type A3rw OCTET STRING .1.3.6.1.4.1.248.14.2.11.4 |
hmRelayServerGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.2.11.10 |
hmRelayDHCPServerIpAddrThe IP address of the first DHCP-server to be addressed
by the relay agent.
If 0.0.0.0, DHCP relaying is switched off for this entry.rw IpAddress .1.3.6.1.4.1.248.14.2.11.10.1 |
hmRelayDHCPServer2IpAddrThe IP address of the second DHCP-server to be addressed
by the relay agent.
If 0.0.0.0, DHCP relaying is switched off for this entry.rw IpAddress .1.3.6.1.4.1.248.14.2.11.10.2 |
hmRelayDHCPServer3IpAddrThe IP address of the third DHCP-server to be addressed
by the relay agent.
If 0.0.0.0, DHCP relaying is switched off for this entry.rw IpAddress .1.3.6.1.4.1.248.14.2.11.10.3 |
hmRelayDHCPServer4IpAddrThe IP address of the fourth DHCP-server to be addressed
by the relay agent.
If 0.0.0.0, DHCP relaying is switched off for this entry.rw IpAddress .1.3.6.1.4.1.248.14.2.11.10.4 |
hmRelayInterfaceTableThis table contains variables for each interface of
the switch. SEQUENCE OF HmRelayInterfaceEntry .1.3.6.1.4.1.248.14.2.11.11 |
hmRelayInterfaceEntryThe entry of the hmRelayInterfaceTable. HmRelayInterfaceEntry .1.3.6.1.4.1.248.14.2.11.11.1 |
hmRelayIfaceGroupIDindex to identify an interface card. This value is never
greater than hmSysGroupCapacity.ro Integer32 .1.3.6.1.4.1.248.14.2.11.11.1.1 |
hmRelayIfaceIDindex to identify an interface within an interface card.ro Integer32 .1.3.6.1.4.1.248.14.2.11.11.1.2 |
hmRelayIfaceOption82EnableEnable or disable DHCP Option 82 on this physical port.rw Enumeration .1.3.6.1.4.1.248.14.2.11.11.1.3 |
hmRelayIfaceBCRequestFwdEnable or disable relaying of incoming broadcasted
BOOTP/DHCP request packets on this physical port.
Hirschmann Multicast BOOTP/DHCP requests will always be relayed.rw Enumeration .1.3.6.1.4.1.248.14.2.11.11.1.4 |
hmRelayIfaceCircuitIDContains the actual Circuit ID sub option for this interface of the relay agent.
It is a best guess value, since some information is not known
before the actual reception of a BOOTP/DHCP request message.ro OCTET STRING .1.3.6.1.4.1.248.14.2.11.11.1.5 |
hmRelayBCPktInCntThe number of BOOTP/DHCP broadcast request packets received
by the relay agent.ro Counter32 .1.3.6.1.4.1.248.14.2.11.20 |
hmRelayMCPktInCntThe number of BOOTP/DHCP multicast request packets received
by the relay agent.ro Counter32 .1.3.6.1.4.1.248.14.2.11.21 |
hmRelayPktServerRelayCntThe number of BOOTP/DHCP requests relayed to the DHCP Server.ro Counter32 .1.3.6.1.4.1.248.14.2.11.22 |
hmRelayPktClientRelayCntThe number of BOOTP/DHCP replies relayed to the Client.ro Counter32 .1.3.6.1.4.1.248.14.2.11.23 |
hmRelayErrCntThe number of errors encountered within the relay agent.ro Counter32 .1.3.6.1.4.1.248.14.2.11.24 |
hmRelayLastDuplicateIPThe last duplicate ip address encounterd by the relay agent.ro IpAddress .1.3.6.1.4.1.248.14.2.11.25 |
hmDeviceMonitoringGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.2.12 |
hmSigConConfigTableThis table contains all variables to configure the behaviour
of the signalling contacts. SEQUENCE OF HmSigConConfigEntry .1.3.6.1.4.1.248.14.2.12.1 |
hmSigConConfigEntryThe entry of the hmSigConConfigTable. HmSigConConfigEntry .1.3.6.1.4.1.248.14.2.12.1.1 |
hmSigConIDThis index is used to identify the associated
signalling contact.ro Integer32 .1.3.6.1.4.1.248.14.2.12.1.1.1 |
hmSigConTrapEnableDetermines wether a trap shall be sent or not, when
the signal contact operating state changes.rw Enumeration .1.3.6.1.4.1.248.14.2.12.1.1.2 |
hmSigConTrapCauseThis object identifies the cause for a trap.
The index of the entity which produces the trap
is specified by hmSigConTrapCauseIndex.ro Enumeration .1.3.6.1.4.1.248.14.2.12.1.1.3 |
hmSigConTrapCauseIndexThis attribute specifies the entity which produces the trap.
1 - n: index of powersupply table / interfaces table
0: other errorsro Integer32 .1.3.6.1.4.1.248.14.2.12.1.1.4 |
hmSigConModeThis attribute specifies the behaviour of the relay contact.
The factory settings for signal contact 1 is monitoring the
correct operation of entries specified to be survied.
When the device has also a second signal contact, the factory
setting for it is the manual mode.rw Enumeration .1.3.6.1.4.1.248.14.2.12.1.1.5 |
hmSigConManualActivateWhen operating in manual mode, the signal contact state can
be set by this attribute.rw Enumeration .1.3.6.1.4.1.248.14.2.12.1.1.6 |
hmSigConOperStateThis attribute shows the current operating state of the
signal contact.ro Enumeration .1.3.6.1.4.1.248.14.2.12.1.1.7 |
hmSigConSenseLinkFailureSets the monitoring of the network connection(s).rw Enumeration .1.3.6.1.4.1.248.14.2.12.1.1.8 |
hmSigConSenseControlLineSets the monitoring of the ring/network coupling.rw Enumeration .1.3.6.1.4.1.248.14.2.12.1.1.9 |
hmSigConSenseRedNotGuaranteedSets the monitoring of the HIPER-Ring.rw Enumeration .1.3.6.1.4.1.248.14.2.12.1.1.10 |
hmSigConSensePS1StateSets the monitoring of the power supply 1.rw Enumeration .1.3.6.1.4.1.248.14.2.12.1.1.11 |
hmSigConSensePS2StateSets the monitoring of the power supply 2.rw Enumeration .1.3.6.1.4.1.248.14.2.12.1.1.12 |
hmSigConSenseTemperatureSets the monitoring of the device temperature.rw Enumeration .1.3.6.1.4.1.248.14.2.12.1.1.13 |
hmSigConSenseModuleRemovalSets the monitoring of module removal (platform dependant).rw Enumeration .1.3.6.1.4.1.248.14.2.12.1.1.14 |
hmSigConSenseACARemovalSets the monitoring of the auto configuration adapter removal.rw Enumeration .1.3.6.1.4.1.248.14.2.12.1.1.15 |
hmSigConSensePS3StateSets the monitoring of the power supply 3 (platform dependant).rw Enumeration .1.3.6.1.4.1.248.14.2.12.1.1.16 |
hmSigConSensePS4StateSets the monitoring of the power supply 4 (platform dependant).rw Enumeration .1.3.6.1.4.1.248.14.2.12.1.1.17 |
hmSigConSenseFan1StateSets the monitoring of the cooling fan (platform dependant).rw Enumeration .1.3.6.1.4.1.248.14.2.12.1.1.18 |
hmSigConSensePS5StateSets the monitoring of the power supply 5 (platform dependant).rw Enumeration .1.3.6.1.4.1.248.14.2.12.1.1.19 |
hmSigConSensePS6StateSets the monitoring of the power supply 6 (platform dependant).rw Enumeration .1.3.6.1.4.1.248.14.2.12.1.1.20 |
hmSigConSensePS7StateSets the monitoring of the power supply 7 (platform dependant).rw Enumeration .1.3.6.1.4.1.248.14.2.12.1.1.21 |
hmSigConSensePS8StateSets the monitoring of the power supply 8 (platform dependant).rw Enumeration .1.3.6.1.4.1.248.14.2.12.1.1.22 |
hmSigConSenseACANotInSyncSets the monitoring whether the configuration on ACA is in
sync with the configuration in NVRAM.rw Enumeration .1.3.6.1.4.1.248.14.2.12.1.1.23 |
hmSigConLinkTableThis table contains all variables to mask an alarm for the
signalling relay, produced by a link. The index for a link
corresponds with ifMauIfIndex. The table is also used
for the device monitoring configuration. SEQUENCE OF HmSigConLinkEntry .1.3.6.1.4.1.248.14.2.12.2 |
hmSigConLinkEntryThe entry of the hmSigConLinkTable. HmSigConLinkEntry .1.3.6.1.4.1.248.14.2.12.2.1 |
hmSigConLinkIDThis index is used to identify the associated link and
corresponds with ifMauIfIndex.ro Integer32 .1.3.6.1.4.1.248.14.2.12.2.1.1 |
hmSigConLinkAlarmIndicates whether an alarm for the signalling relay of the
associated link will be produced or not, so you can mask the
value of ifMauMediaAvailable.rw Enumeration .1.3.6.1.4.1.248.14.2.12.2.1.2 |
hmDevMonConfigTableThis table contains all variables to configure the behaviour
of the device state. SEQUENCE OF HmDevMonConfigEntry .1.3.6.1.4.1.248.14.2.12.3 |
hmDevMonConfigEntryConfiguration of the device monitoring. HmDevMonConfigEntry .1.3.6.1.4.1.248.14.2.12.3.1 |
hmDevMonIDThis index is used to identify the associated
device status (currently only one).ro Integer32 .1.3.6.1.4.1.248.14.2.12.3.1.1 |
hmDevMonTrapEnableDetermines wether a trap shall be sent or not, when
the device monitoring state changes.rw Enumeration .1.3.6.1.4.1.248.14.2.12.3.1.2 |
hmDevMonTrapCauseThis object identifies the cause for a trap.
The index of the entity which produces the trap
is specified by hmDevMonTrapCauseIndex.ro Enumeration .1.3.6.1.4.1.248.14.2.12.3.1.3 |
hmDevMonTrapCauseIndexThis attribute specifies the entity which produces the trap.
1 - n: index of powersupply table / interfaces table
0: other errorsro Integer32 .1.3.6.1.4.1.248.14.2.12.3.1.4 |
hmDevMonSwitchStateThis attribute shows the current state of the
device monitoring.ro Enumeration .1.3.6.1.4.1.248.14.2.12.3.1.5 |
hmDevMonSenseLinkFailureSets the monitoring of the network connection(s).rw Enumeration .1.3.6.1.4.1.248.14.2.12.3.1.6 |
hmDevMonSenseControlLineSets the monitoring of the ring/network coupling.rw Enumeration .1.3.6.1.4.1.248.14.2.12.3.1.7 |
hmDevMonSenseRedNotGuaranteedSets the monitoring of the HIPER-Ring.rw Enumeration .1.3.6.1.4.1.248.14.2.12.3.1.8 |
hmDevMonSensePS1StateSets the monitoring of the power supply 1.rw Enumeration .1.3.6.1.4.1.248.14.2.12.3.1.9 |
hmDevMonSensePS2StateSets the monitoring of the power supply 2.rw Enumeration .1.3.6.1.4.1.248.14.2.12.3.1.10 |
hmDevMonSenseTemperatureSets the monitoring of the device temperature.rw Enumeration .1.3.6.1.4.1.248.14.2.12.3.1.11 |
hmDevMonSenseModuleRemovalSets the monitoring of module removal (platform dependant).rw Enumeration .1.3.6.1.4.1.248.14.2.12.3.1.12 |
hmDevMonSenseACARemovalSets the monitoring of the auto configuration adapter removal.rw Enumeration .1.3.6.1.4.1.248.14.2.12.3.1.13 |
hmDevMonSensePS3StateSets the monitoring of the power supply 3 (platform dependant).rw Enumeration .1.3.6.1.4.1.248.14.2.12.3.1.14 |
hmDevMonSensePS4StateSets the monitoring of the power supply 4 (platform dependant).rw Enumeration .1.3.6.1.4.1.248.14.2.12.3.1.15 |
hmDevMonSenseFan1StateSets the monitoring of the cooling fan (platform dependant).rw Enumeration .1.3.6.1.4.1.248.14.2.12.3.1.16 |
hmDevMonSensePS5StateSets the monitoring of the power supply 5 (platform dependant).rw Enumeration .1.3.6.1.4.1.248.14.2.12.3.1.17 |
hmDevMonSensePS6StateSets the monitoring of the power supply 6 (platform dependant).rw Enumeration .1.3.6.1.4.1.248.14.2.12.3.1.18 |
hmDevMonSensePS7StateSets the monitoring of the power supply 7 (platform dependant).rw Enumeration .1.3.6.1.4.1.248.14.2.12.3.1.19 |
hmDevMonSensePS8StateSets the monitoring of the power supply 8 (platform dependant).rw Enumeration .1.3.6.1.4.1.248.14.2.12.3.1.20 |
hmDevMonSenseACANotInSyncSets the monitoring whether the configuration on ACA is in sync with the configuration in NVRAM.rw Enumeration .1.3.6.1.4.1.248.14.2.12.3.1.21 |
hmAgentSnmpConfigGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.2.13 |
hmAgentSnmpCommunityCreateCreates a new SNMP Community entry.
Defaults: IPAddress 0.0.0.0
IpMask 0.0.0.0
AccessMode read-only
Status configrw DisplayString .1.3.6.1.4.1.248.14.2.13.1 |
hmAgentSnmpCommunityConfigTableA table of the switch's SNMP Config entries SEQUENCE OF HmAgentSnmpCommunityConfigEntry .1.3.6.1.4.1.248.14.2.13.2 |
hmAgentSnmpCommunityConfigEntrySwitch's SNMP Config entry HmAgentSnmpCommunityConfigEntry .1.3.6.1.4.1.248.14.2.13.2.1 |
hmAgentSnmpCommunityIndexThe switch's Snmp Community Indexro Integer32 .1.3.6.1.4.1.248.14.2.13.2.1.1 |
hmAgentSnmpCommunityNameThe switch's Snmp Community Name
This name identifies each SNMP community;
the name can be up to 32 characters, and it is case-sensitive.
Community names in the SNMP community must be unique.
If you make multiple entries using the same community name,
the first entry is kept and processed and all duplicate entries are ignored.rw DisplayString .1.3.6.1.4.1.248.14.2.13.2.1.2 |
hmAgentSnmpCommunityIPAddressThe switch's Snmp Community IP Address
Client IP Address - This attribute is an IP address (or portion thereof)
from which this device will accept SNMP packets with the associated
community. The requesting entity's IP address is logical-ANDed with
the Client IP Mask and the result must match the Client IP Address.
Note: If the Client IP Mask is set
to 0.0.0.0, a Client IP Address of 0.0.0.0 matches all IP addresses.rw IpAddress .1.3.6.1.4.1.248.14.2.13.2.1.3 |
hmAgentSnmpCommunityIPMaskThe switch's Snmp Community IP Mask
Client IP Mask - This attribute is a mask to be logical-ANDed with the
requesting entity's IP address before comparison with the Client IP Address.
If the result matches with Client IP Address then the address is an
authenticated IP address. For example, if the Client IP Address
is 9.47.128.0 and the corresponding Client IP Mask is 255.255.255.0,
a range of incoming IP addresses would match, that is, the incoming IP
addresses could be a value in the following range: 9.47.128.0 to 9.47.128.255.
To have a specific IP address be the only authenticated IP address, set the
Client IP Address to the required IP address and set the Client IP Mask
to 255.255.255.255.rw IpAddress .1.3.6.1.4.1.248.14.2.13.2.1.4 |
hmAgentSnmpCommunityAccessModeThe switch's Snmp Community Access Mode
Access Mode - This value can be read-only or read/write.
A community with a read-only access allows for switch information to be
displayed. A community with a read/write access allows for configuration
changes to be made and for information to be displayed.rw Enumeration .1.3.6.1.4.1.248.14.2.13.2.1.5 |
hmAgentSnmpCommunityStatusThe switch's Snmp Community Status.
active(1) - This community is active, allowing SNMP managers associated
with this community to manage the switch according to its
access right.
notInService(2) - This community is not active; no SNMP requests using this
community will be accepted. In this case the SNMP manager
associated with this community cannot manage the switch until
the Status is changed back to active(1).
config(3) - The community Status must be set to this value in order to
configure it. When creating a new community entry, initial
Status will be set to this value.
destroy(4) - Set to this value to remove the community from the agent.rw Enumeration .1.3.6.1.4.1.248.14.2.13.2.1.6 |
hmAgentSnmpTrapReceiverCreateCreates a new trap receiver entry.
Defaults: IPAddress 0.0.0.0
status configrw DisplayString .1.3.6.1.4.1.248.14.2.13.3 |
hmAgentSnmpTrapReceiverConfigTableTrap messages are sent across a network to an SNMP Network Manager.
These messages alert the manager to events occurring within the switch
or on the network. Up to six simultaneous trap receivers are supported. SEQUENCE OF HmAgentSnmpTrapReceiverConfigEntry .1.3.6.1.4.1.248.14.2.13.4 |
hmAgentSnmpTrapReceiverConfigEntrySwitch's Snmp Trace Receiver Config entry HmAgentSnmpTrapReceiverConfigEntry .1.3.6.1.4.1.248.14.2.13.4.1 |
hmAgentSnmpTrapReceiverIndexThe switch's Snmp Trap Receiver Indexro Integer32 .1.3.6.1.4.1.248.14.2.13.4.1.1 |
hmAgentSnmpTrapReceiverCommunityNameThe switch's Snmp Trap Receiver Community Name.
This is the SNMP community name of the remote network manager;
the name can be up to 16 characters, and is case-sensitive.rw DisplayString .1.3.6.1.4.1.248.14.2.13.4.1.2 |
hmAgentSnmpTrapReceiverIPAddressIP Address - Each IP address parameter is four integer numbers.
The numbers range from 0 to 255.rw IpAddress .1.3.6.1.4.1.248.14.2.13.4.1.3 |
hmAgentSnmpTrapReceiverStatusThe switch's Snmp Trap Reciever Status.
active(1) - This trap receiver is active, allowing SNMP Traps to
be sent to this receiver.
notInService(2) - This trap reciever is not active; no SNMP Traps will
be sent to this reciever until it's set back to active(1).
config(3) - The trap reciever Status must be set to this value in order
to configure it. When creating a new trap receiver entry,
the Status will initially be set to this value.
Note: hmAgentSnmpTrapReceiverIPAddress must be set to non-zero
before changing to active(1) or notInService(2).
destroy(4) - Set to this value to remove the trap receiver entry from
the agent.rw Enumeration .1.3.6.1.4.1.248.14.2.13.4.1.4 |
hmAgentSnmpTrapFlagsConfigGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.2.13.5 |
hmAgentSnmpAuthenticationTrapFlagAuthentication Flag - Enable/Disable authentication Flag.rw Enumeration .1.3.6.1.4.1.248.14.2.13.5.1 |
hmAgentSnmpLinkUpDownTrapFlagLink Up/Down Flag - Enable/Disable Link Up/Link Down traps for the
entire switch. When set to Enable, the Link Up/Down traps will be
sent only if the Link Trap flag setting associated with the port
(Port Configuration Menu) is set to Enable.rw Enumeration .1.3.6.1.4.1.248.14.2.13.5.2 |
hmAgentSnmpMultipleUsersTrapFlagMultiple Users Flag - Enable/Disable Multiple User traps. When the value
is set to Enable, a Multiple User Trap is sent whenever someone logs in
to the terminal interface (EIA 232 or Telnet) and there is already an
existing terminal interface session.rw Enumeration .1.3.6.1.4.1.248.14.2.13.5.3 |
hmAgentSnmpSpanningTreeTrapFlagSpanning Tree Flag - This flag enables the sending of new root traps and
topology change notification traps.rw Enumeration .1.3.6.1.4.1.248.14.2.13.5.4 |
hmAgentSnmpBroadcastStormTrapFlagBroadcast Storm Flag - This flag enables or disables the broadcast
storm trap. You must also enable Broadcast Storm Recovery Mode
(see the Switch Configuration Menu). When this
value is set to Enable and Broadcast Storm Recovery mode is set to Enable,
the Broadcast Storm Start/End traps are sent when the switch enters and
leaves Broadcast Storm Recovery.rw Enumeration .1.3.6.1.4.1.248.14.2.13.5.5 |
hmAgentSnmpChassisTrapFlagChassis Flag - Enable/Disable traps for
hmTemperatureTrap
hmModuleMapChange
hmPowerSupplyTrap
hmAutoconfigAdapterTraprw Enumeration .1.3.6.1.4.1.248.14.2.13.5.6 |
hmAgentSnmpL2RedundancyTrapFlagChassis Flag - Enable/Disable traps
hmRingRedReconfig and hmRingCplReconfigrw Enumeration .1.3.6.1.4.1.248.14.2.13.5.7 |
hmAgentSnmpPortSecurityTrapFlagPortSecurity Flag - enable/disable all port security traps.rw Enumeration .1.3.6.1.4.1.248.14.2.13.5.8 |
hmAgentSnmpCommunityMaxEntriesMax number of Entries in hmAgentSnmpCommunityConfigEntryro Integer32 .1.3.6.1.4.1.248.14.2.13.6 |
hmAgentSnmpTrapReceiverMaxEntriesMax number of Entries in hmAgentSnmpTrapReceiverConfigEntryro Integer32 .1.3.6.1.4.1.248.14.2.13.7 |
hmAgentSnmpLoggingGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.2.13.8 |
hmAgentSnmpLogGetRequestEnable logging of SNMP GET requests.rw Enumeration .1.3.6.1.4.1.248.14.2.13.8.1 |
hmAgentSnmpLogSetRequestEnable logging of SNMP SET requests.rw Enumeration .1.3.6.1.4.1.248.14.2.13.8.2 |
hmAgentSnmpLogGetSeverityDefine the log severity for SNMP GET requests.rw HmAgentLogSeverity .1.3.6.1.4.1.248.14.2.13.8.3 |
hmAgentSnmpLogSetSeverityDefine the log severity for SNMP SET requests.rw HmAgentLogSeverity .1.3.6.1.4.1.248.14.2.13.8.4 |
hmPOEGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.2.14 |
hmPOEGlobalGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.2.14.1 |
hmPOEStatusEnables/disables Power over Ethernet on this device.
The default value is enable.rw Enumeration .1.3.6.1.4.1.248.14.2.14.1.1 |
hmPOEScanningEnables/disables port scanning on this device.
The default value is enable.rw Enumeration .1.3.6.1.4.1.248.14.2.14.1.2 |
hmPOEReservedPowerReserved system power for active Power over Ethernet ports in Watts.ro Integer32 .1.3.6.1.4.1.248.14.2.14.1.3 |
hmPOEFastStartupEnables/disables Power over Ethernet on this device.
The default value is enable.rw Enumeration .1.3.6.1.4.1.248.14.2.14.1.4 |
hmPOEPortTableThis table contains variables for each Power over Ethernet interface of
the switch. SEQUENCE OF HmPOEPortEntry .1.3.6.1.4.1.248.14.2.14.2 |
hmPOEPortEntryThe entry of the hmPOEPortTable. HmPOEPortEntry .1.3.6.1.4.1.248.14.2.14.2.1 |
hmPOEPortIndexIndex to identify an Power over Ethernet interface.ro Integer32 .1.3.6.1.4.1.248.14.2.14.2.1.1 |
hmPOEPortConsumptionPowerMeasured usage power per interface expressed in Milliwatts.ro Integer32 .1.3.6.1.4.1.248.14.2.14.2.1.2 |
hmPOEModuleTableThis table contains objects for each plugged PoE+ module of
the switch. If the device is non-modular and supports PoE+ it
contains only one entry. SEQUENCE OF HmPOEModuleEntry .1.3.6.1.4.1.248.14.2.14.3 |
hmPOEModuleEntryThe entries of the hmPOEModuleTable. HmPOEModuleEntry .1.3.6.1.4.1.248.14.2.14.3.1 |
hmPOEModuleIndexSlot number of the plugged PoE+ module.ro Integer32 .1.3.6.1.4.1.248.14.2.14.3.1.1 |
hmPOEModulePowerConfigurable power budget per module expressed in Watts. The default
value is hmPOEModuleMaximumPower and depends on the hardware.rw Integer32 .1.3.6.1.4.1.248.14.2.14.3.1.2 |
hmPOEModuleMaximumPowerMaximum available power budget per module expressed in Watts. This
value depends on the device or module.ro Integer32 .1.3.6.1.4.1.248.14.2.14.3.1.3 |
hmPOEModuleReservedPowerThe reserved power (depending on actual power classes)
per module expressed in Watts.ro Integer32 .1.3.6.1.4.1.248.14.2.14.3.1.4 |
hmPOEModuleDeliveredPowerThe measured usage power per module expressed in Watts.ro Integer32 .1.3.6.1.4.1.248.14.2.14.3.1.5 |
hmPOEModuleUsageThresholdThe usage power threshold per module expressed in percent.
If this threshold is exceeded a alarm is initiated.rw Integer32 .1.3.6.1.4.1.248.14.2.14.3.1.6 |
hmPOEModuleNotificationControlEnableThis object controls, on a per-module basis, whether
or not notifications from the agent are enabled.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.248.14.2.14.3.1.7 |
hmSwitchResources OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.2.15 |
hmEnableMeasurementEnable or disable the resources measurement If disabled, the
task - needed for measurement - is also deleted.rw Enumeration .1.3.6.1.4.1.248.14.2.15.1 |
hmCpuResources OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.2.15.2 |
hmCpuUtilizationThe current cpu utilization of the switch in percent.ro Integer32 .1.3.6.1.4.1.248.14.2.15.2.1 |
hmCpuAverageUtilizationThe average cpu utilization of the switch in percent,
max. measured over the last 30 minutes.ro Integer32 .1.3.6.1.4.1.248.14.2.15.2.2 |
hmCpuRunningProcessesThe current number of processes running.ro Integer32 .1.3.6.1.4.1.248.14.2.15.2.3 |
hmCpuMaxRunningProcessesThe maximum number of processes running, max. since
the last 30 minutes.ro Integer32 .1.3.6.1.4.1.248.14.2.15.2.4 |
hmMemoryResources OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.2.15.3 |
hmMemoryAllocatedThe current allocated memory of the switch in kBytes.ro Integer32 .1.3.6.1.4.1.248.14.2.15.3.1 |
hmMemoryFreeThe current free memory of the switch in kBytes.ro Integer32 .1.3.6.1.4.1.248.14.2.15.3.2 |
hmMemoryAllocatedAverageThe average allocated memory of the switch in kBytes,
measured over the last 30 minutes.ro Integer32 .1.3.6.1.4.1.248.14.2.15.3.3 |
hmMemoryFreeAverageThe average free memory of the switch in kBytes,
measured over the last 30 minutes.ro Integer32 .1.3.6.1.4.1.248.14.2.15.3.4 |
hmNetworkResources OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.2.15.4 |
hmNetworkCpuIfUtilizationThe current network utilization of the internal cpu interface in percent.ro Integer32 .1.3.6.1.4.1.248.14.2.15.4.1 |
hmNetworkCpuIfAverageUtilizationThe average network utilization of the internal cpu interface in percent,
measured over the last 30 minutes.ro Integer32 .1.3.6.1.4.1.248.14.2.15.4.2 |
hmIndustrialEthernetProtocols OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.2.16 |
hmProfinetIOConfigGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.2.16.1 |
hmPNIOAdminStatusEnables/disables the ProfinetIO functionality
on this device.
If disabled(2), the ProfinetIO protocol is inactive,
but the ProfinetIO MIBs can be accessed.
The default value is disabled.rw Enumeration .1.3.6.1.4.1.248.14.2.16.1.1 |
hmPNIODeviceIDIdentifier of the device family.
Values 1 .. 65635 are valid device IDs.ro Integer32 .1.3.6.1.4.1.248.14.2.16.1.2 |
hmPNIOModuleIdentNumberIdentifier ID of the device of port or module.ro Integer32 .1.3.6.1.4.1.248.14.2.16.1.3 |
hmPNIOOrderIDProduct (switch) order ID.
The size is restricted to 64 characters.ro DisplayString .1.3.6.1.4.1.248.14.2.16.1.4 |
hmPNIODeviceTypeDetailsSwitch device type details, for example:
4 Port Rail Switch.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.248.14.2.16.1.5 |
hmPNIOSoftwareReleaseThis value is a string that contains Version number of
software in profinetio format, for example: 01.0.03.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.248.14.2.16.1.6 |
hmPNIOHardwareReleaseVersion number of switch hardware in profinetio format.ro Integer32 .1.3.6.1.4.1.248.14.2.16.1.7 |
hmPNIOOrderID9thProduct (switch) order ID.
The size is restricted to 32 characters
(In the form of the 9-th numbers).ro DisplayString .1.3.6.1.4.1.248.14.2.16.1.8 |
hmPNIODcpModeTableTable of DCP mode entries SEQUENCE OF HmPNIODcpModeEntry .1.3.6.1.4.1.248.14.2.16.1.10 |
hmPNIODcpModeEntryDCP mode entry HmPNIODcpModeEntry .1.3.6.1.4.1.248.14.2.16.1.10.1 |
hmPNIODcpModePortIDPort ID for the DCP mode table entryro INTEGER .1.3.6.1.4.1.248.14.2.16.1.10.1.1 |
hmPNIODcpModeDCP mode for one port.
Allowed values none(0), ingress(1), egress(2) or both(3) which is default.rw Enumeration .1.3.6.1.4.1.248.14.2.16.1.10.1.2 |
hmPNIONameOfStationDevice name.
The size is restricted to 240 characters.
It must be conform to the restrictions
as decribed in PNIO protocol specification.rw DisplayString .1.3.6.1.4.1.248.14.2.16.1.11 |
hmProfinetIOStatisticsGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.2.16.2 |
hmEthernetIPConfigGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.2.16.3 |
hmEtherNetIPAdminStatusEnables/disables the EtherNet/IP(TM) functionality
on this device.
If disabled(2), the EtherNet/IP protocol is deactivated,
but the EtherNet/IP MIBs can be accessed.
The default value is disabled.rw Enumeration .1.3.6.1.4.1.248.14.2.16.3.1 |
hmEtherNetIPErrorCodeRead the error code within EtherNet/IP(TM) action.ro Integer32 .1.3.6.1.4.1.248.14.2.16.3.2 |
hmEtherNetIPProductCodeRead the Product Code as shown in the Identity Object
of EtherNet/IP(TM). Values 1 .. 65635 are valid product codes.ro Integer32 .1.3.6.1.4.1.248.14.2.16.3.3 |
hmEtherNetIPRevisionMajorRead the major revision number as shown in the Identity Object
of EtherNet/IP(TM). Values 1 .. 255 are valid revisions.ro Integer32 .1.3.6.1.4.1.248.14.2.16.3.4 |
hmEtherNetIPRevisionMinorRead the minor revision number as shown in the Identity Object
of EtherNet/IP(TM). Values 1 .. 255 are valid revisions.ro Integer32 .1.3.6.1.4.1.248.14.2.16.3.5 |
hmEtherNetIPProductNameRead the product name as shown in the Identity Object
of EtherNet/IP(TM). The size is restricted to 32 Characters.ro DisplayString .1.3.6.1.4.1.248.14.2.16.3.6 |
hmEtherNetIPCatalogNameRead the catolog name as provided in the EDS file
for EtherNet/IP(TM). The size is restricted to 255 Characters.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.248.14.2.16.3.7 |
hmEthernetIPStatisticsGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.2.16.4 |
hmEtherNetIPConnEstablishedStatistics: number of connections that have been established
within EtherNet/IP.ro Integer32 .1.3.6.1.4.1.248.14.2.16.4.1 |
hmEtherNetIPConnTimeoutsStatistics: number of connection timeouts that have been occurred
within EtherNet/IP.ro Integer32 .1.3.6.1.4.1.248.14.2.16.4.2 |
hmEtherNetIPVendorObjRequestsStatistics: number of requests to the vendor specific objects
within EtherNet/IP.ro Integer32 .1.3.6.1.4.1.248.14.2.16.4.3 |
hmAgentLoginGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.2.17 |
hmAgentLoginBannerThe text added in this variable by the user will be display in
the system login page as banner on every login into the CLI
(local or remote) or when login into the system web interface.
The default value is an empty string, which will not be displayed.
Special meaning have the sequences '\t' and '\n' which
allow the user to format the string with tabulator (t)
and newline (n) format instructions.rw OCTET STRING .1.3.6.1.4.1.248.14.2.17.1 |
hmPortMonitorGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.2.18 |
hmPortMonitorAdminModeGlobal switch to enable / disable the port state actions,
which are performed if a condition becomes truerw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.248.14.2.18.1 |
hmPortMonitorIntfTablePort state mode interface table. SEQUENCE OF HmPortMonitorIntfEntry .1.3.6.1.4.1.248.14.2.18.2 |
hmPortMonitorIntfEntryPort state mode interface entry. HmPortMonitorIntfEntry .1.3.6.1.4.1.248.14.2.18.2.1 |
hmPortMonitorIntfModePort monitor interface mode.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.248.14.2.18.2.1.1 |
hmPortMonitorIntfResetPort monitor interface reset.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.248.14.2.18.2.1.2 |
hmPortMonitorIntfActionInterface link disable state.rw Enumeration .1.3.6.1.4.1.248.14.2.18.2.1.3 |
hmPortMonitorConditionGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.2.18.3 |
hmPortMonitorConditionTablePort state condition interface table. SEQUENCE OF HmPortMonitorConditionIntfEntry .1.3.6.1.4.1.248.14.2.18.3.1 |
hmPortMonitorConditionIntfEntryPort state action interface entry. HmPortMonitorConditionIntfEntry .1.3.6.1.4.1.248.14.2.18.3.1.1 |
hmPortMonitorConditionLinkFlapModeInterface link flap mode.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.248.14.2.18.3.1.1.1 |
hmPortMonitorConditionCrcFragmentsModeInterface CrcFragments mode.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.248.14.2.18.3.1.1.2 |
hmPortMonitorConditionFieldCondition type field.ro Bits .1.3.6.1.4.1.248.14.2.18.3.1.1.3 |
hmPortMonitorConditionLinkFlapGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.2.18.3.2 |
hmPortMonitorConditionLinkFlapIntervalMeasure interval in seconds (1-180s) for link flap detection.rw Integer32 .1.3.6.1.4.1.248.14.2.18.3.2.1 |
hmPortMonitorConditionLinkFlapCountLink flap counter (1-100).rw Integer32 .1.3.6.1.4.1.248.14.2.18.3.2.2 |
hmPortMonitorConditionLinkFlapIntfTablePort condition link flap interface table. SEQUENCE OF HmPortMonitorConditionLinkFlapIntfEntry .1.3.6.1.4.1.248.14.2.18.3.2.3 |
hmPortMonitorConditionLinkFlapIntfEntryPort condition link flap interface entry. HmPortMonitorConditionLinkFlapIntfEntry .1.3.6.1.4.1.248.14.2.18.3.2.3.1 |
hmPortMonitorConditionLinkFlapCountIntervalLink flap count that occured in last interval.ro Integer32 .1.3.6.1.4.1.248.14.2.18.3.2.3.1.1 |
hmPortMonitorConditionLinkFlapCountTotalTotal link flap count.ro Integer32 .1.3.6.1.4.1.248.14.2.18.3.2.3.1.2 |
hmPortMonitorConditionCrcFragmentsGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.2.18.3.3 |
hmPortMonitorConditionCrcFragmentsIntervalMeasure interval in seconds (5-180s) for CrcFragments detection.rw Integer32 .1.3.6.1.4.1.248.14.2.18.3.3.1 |
hmPortMonitorConditionCrcFragmentsCountCrcFragments counter (1-1000000).rw Integer32 .1.3.6.1.4.1.248.14.2.18.3.3.2 |
hmPortMonitorConditionCrcFragmentsIntfTablePort condition CrcFragments interface table. SEQUENCE OF HmPortMonitorConditionCrcFragmentsIntfEntry .1.3.6.1.4.1.248.14.2.18.3.3.3 |
hmPortMonitorConditionCrcFragmentsIntfEntryPort condition CrcFragments interface entry. HmPortMonitorConditionCrcFragmentsIntfEntry .1.3.6.1.4.1.248.14.2.18.3.3.3.1 |
hmPortMonitorConditionCrcFragmentsCountIntervalCrcFragments count that occured in last interval.ro Integer32 .1.3.6.1.4.1.248.14.2.18.3.3.3.1.1 |
hmPortMonitorConditionCrcFragmentsCountTotalTotal CrcFragments count.ro Integer32 .1.3.6.1.4.1.248.14.2.18.3.3.3.1.2 |
hmProducts OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.10 |
rs2 OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.10.2 |
mach3000 OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.10.3 |
ms2108-2 OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.10.4 |
ms3124-4 OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.10.5 |
rs2-16 OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.10.6 |
rs2-4r OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.10.7 |
ms4128-5 OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.10.10 |
eagle OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.10.20 |
rr-epl OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.10.21 |
eagle-mguard OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.10.22 |
eagle20 OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.10.23 |
ms20 OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.10.30 |
ms30 OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.10.31 |
rs20 OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.10.40 |
rs30 OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.10.41 |
rsb20 OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.10.44 |
osb20 OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.10.45 |
mach4002-48-4G OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.10.50 |
octopus OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.10.60 |
mach4002-24G OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.10.70 |
mach4002-24G-3X OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.10.71 |
mach4002-48G OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.10.75 |
mach4002-48G-3X OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.10.76 |
ruggedswitch OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.10.90 |
railswitchrugged OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.10.100 |
mach100 OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.10.110 |
octopus-os OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.10.120 |
mach100ge OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.10.130 |
mach1000ge OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.10.131 |
eem1 OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.10.200 |