HIRSCHMANN-MMP4-BASICL2-MIB
AI MIB Summary
The HIRSCHMANN-MMP4-BASICL2-MIB module provides SNMP management definitions for monitoring Layer 2 switching functions, including port status, MAC address tables, and VLAN configurations, on Hirschmann (Belden) Platform4 series network devices.
The Hirschmann Private Platform4 Basic Layer 2 MIB definitions for Platform devices.
Main OID:
hmPlatform4BasicL2.1.3.6.1.4.1.248.15.1
401
Objects
Active
Status
8
Dependencies
Imported Objects
Objects
401 total| Object Name |
|---|
hmPlatform4 OBJECT IDENTIFIER .1.3.6.1.4.1.248.15 |
hmPlatform4BasicL2The Hirschmann Private Platform4 Basic Layer 2 MIB definitions for Platform devices. MODULE-IDENTITY .1.3.6.1.4.1.248.15.1 |
hmAgentInfoGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.15.1.1 |
hmAgentTrapLogGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.15.1.1.2 |
hmAgentTrapLogTotalThe total number of traps sent since last reset.ro Integer32 .1.3.6.1.4.1.248.15.1.1.2.1 |
hmAgentTrapLogTotalSinceLastViewedThe number of traps sent since last viewed.rodeprecated Integer32 .1.3.6.1.4.1.248.15.1.1.2.3 |
hmAgentTrapLogTableAgent Trap Log SEQUENCE OF HmAgentTrapLogEntry .1.3.6.1.4.1.248.15.1.1.2.4 |
hmAgentTrapLogEntryAgent trap log entry HmAgentTrapLogEntry .1.3.6.1.4.1.248.15.1.1.2.4.1 |
hmAgentTrapLogIndexUnique index of trap entryro Integer32 .1.3.6.1.4.1.248.15.1.1.2.4.1.1 |
hmAgentTrapLogSystemTimeSystem uptime when trap was sent.
This entry shows how long the system has been up when the trap occurred.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.248.15.1.1.2.4.1.2 |
hmAgentTrapLogTrapDescription of the trap sent.ro DisplayString .1.3.6.1.4.1.248.15.1.1.2.4.1.3 |
hmAgentConfigGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.15.1.2 |
hmAgentCLIConfigGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.15.1.2.1 |
hmAgentLoginSessionTableA table of the switch's login session SEQUENCE OF HmAgentLoginSessionEntry .1.3.6.1.4.1.248.15.1.2.1.1 |
hmAgentLoginSessionEntryLogin Session Entry HmAgentLoginSessionEntry .1.3.6.1.4.1.248.15.1.2.1.1.1 |
hmAgentLoginSessionIndexAgent Login Session Index of the switchro Integer32 .1.3.6.1.4.1.248.15.1.2.1.1.1.1 |
hmAgentLoginSessionUserNameAgent Login Session UserName of the switchro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.248.15.1.2.1.1.1.2 |
hmAgentLoginSessionIPAddressAgent Login Session IP Address of the switchro IpAddress .1.3.6.1.4.1.248.15.1.2.1.1.1.3 |
hmAgentLoginSessionConnectionTypeAgent Login Session Connection Type of the switchro Enumeration .1.3.6.1.4.1.248.15.1.2.1.1.1.4 |
hmAgentLoginSessionIdleTimeAgent Login Session Idle Time of the switchro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.248.15.1.2.1.1.1.5 |
hmAgentLoginSessionSessionTimeAgent Login Session Time of the switchro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.248.15.1.2.1.1.1.6 |
hmAgentLoginSessionStatusStatus of the user.
active(1) - This connection is active.
destroy(6) - Set to this value to disconnect this user.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.248.15.1.2.1.1.1.7 |
hmAgentTelnetConfigGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.15.1.2.1.2 |
hmAgentTelnetLoginTimeoutTelnet login timeout (minutes)
Config telnet timeout will set the telnet session timeout value.
A session is active as long as the session has not remained idle for
the value set. Specify a value from 1 to 160.
Note: Changing the timeout value for active
sessions does not become effective until the session is reaccessed.
Any keystroke will also activate the new timeout duration.rw Integer32 .1.3.6.1.4.1.248.15.1.2.1.2.1 |
hmAgentTelnetMaxSessionsMaximum number of Telnet Sessions
Config telnet maxsessions is an integer value from 0 to 5 that specifies the
maximum number of telnet sessions that can be established.
If the value is 0, no Telnet session can be established.rw Integer32 .1.3.6.1.4.1.248.15.1.2.1.2.2 |
hmAgentTelnetAllowNewModeAllow new telnet sessions (enable or disable)
Config telnet disable means that no new Telnet sessions are to be
established. Any already established session remains active until
the session is ended or an abnormal network error ends it.rw Enumeration .1.3.6.1.4.1.248.15.1.2.1.2.3 |
hmAgentUserConfigGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.15.1.2.1.3 |
hmAgentUserConfigCreateCreate a new user.
When set with a non-empty string, a new user with that name will be created.
This object will only return an empty string.
This string is limited to alpha-numeric strings (uncluding the '-' and '_' characters).rw DisplayString .1.3.6.1.4.1.248.15.1.2.1.3.1 |
hmAgentUserConfigTableUser Config Table SEQUENCE OF HmAgentUserConfigEntry .1.3.6.1.4.1.248.15.1.2.1.3.2 |
hmAgentUserConfigEntryUser Config Entry HmAgentUserConfigEntry .1.3.6.1.4.1.248.15.1.2.1.3.2.1 |
hmAgentUserIndexAgent User Config Index Integer32 .1.3.6.1.4.1.248.15.1.2.1.3.2.1.1 |
hmAgentUserNameAgent User Name.
This string is limited to alpha-numeric strings (including the '-' and '_' characters).rw DisplayString .1.3.6.1.4.1.248.15.1.2.1.3.2.1.2 |
hmAgentUserPasswordAgent User Password
This object will return an empty string even if a password is set.rw DisplayString .1.3.6.1.4.1.248.15.1.2.1.3.2.1.3 |
hmAgentUserAccessModeAgent User Access Moderw Enumeration .1.3.6.1.4.1.248.15.1.2.1.3.2.1.4 |
hmAgentUserStatusAgent User Status.
active(1) - This user account is active.
destroy(6) - Set to this value to remove this user account.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.248.15.1.2.1.3.2.1.5 |
hmAgentUserAuthenticationTypeSNMPv3 User Authentication. The user passsword must be set
to a string greater than or equal to 8 characters for this to be
set to anything but none(1).
none(1) - no authentication used
hmacmd5(1) - Use HMAC-MD5 authentication
hmacsha(1) - Use HMAC-SHA authenticationrw Enumeration .1.3.6.1.4.1.248.15.1.2.1.3.2.1.6 |
hmAgentUserEncryptionTypeSNMPv3 User Encryption
Can not be set to des(2) if hmAgentUserAuthenticationType is set to
none(1).
none(1) - no encryption used
des(2) - DES encryption usedrw Enumeration .1.3.6.1.4.1.248.15.1.2.1.3.2.1.7 |
hmAgentUserEncryptionPasswordSNMPv3 User Encryption Password
This object will return an empty string even if a password is
set. hmAgentUserEncryptionType must be set to des(2) before this
object can be configured.
This object will return an empty string even if a password is set.rw DisplayString .1.3.6.1.4.1.248.15.1.2.1.3.2.1.8 |
hmAgentUserDefaultPwdActiveShows if one or more default passwords are active for
users configured in the hmAgentUserConfigTable.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.248.15.1.2.1.3.248 |
hmAgentLagConfigGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.15.1.2.2 |
hmAgentLagConfigCreateAgent LAG Create.
When this object is set with a non-empty string, a new LAG will be created
if possible with the entered string as its name.rw DisplayString .1.3.6.1.4.1.248.15.1.2.2.1 |
hmAgentLagSummaryConfigTableA summary table of the switch's LAG config entries SEQUENCE OF HmAgentLagSummaryConfigEntry .1.3.6.1.4.1.248.15.1.2.2.2 |
hmAgentLagSummaryConfigEntrySwitch's LAG config entry HmAgentLagSummaryConfigEntry .1.3.6.1.4.1.248.15.1.2.2.2.1 |
hmAgentLagSummaryLagIndexAgent LAG IfIndex.
This value corresponds with the LAG interface in the ifTable.ro Integer32 .1.3.6.1.4.1.248.15.1.2.2.2.1.1 |
hmAgentLagSummaryNameAgent LAG Name.
The associated name of the LAG used during creation.rw DisplayString .1.3.6.1.4.1.248.15.1.2.2.2.1.2 |
hmAgentLagSummaryFlushTimerAgent LAG FlushTimer.rwobsolete Integer32 .1.3.6.1.4.1.248.15.1.2.2.2.1.3 |
hmAgentLagSummaryLinkTrapAgent LAG LinkTrap.
Configures sending Link Up/Down traps when the LAG interface goes Up or Down.rw Enumeration .1.3.6.1.4.1.248.15.1.2.2.2.1.4 |
hmAgentLagSummaryAdminModeAgent LAG AdminMode.
Administratively enables or disables this LAG interface.rw Enumeration .1.3.6.1.4.1.248.15.1.2.2.2.1.5 |
hmAgentLagSummaryStpModeAgent LAG StpMode.rw Enumeration .1.3.6.1.4.1.248.15.1.2.2.2.1.6 |
hmAgentLagSummaryAddPortAgent LAG AddPort.
Set to a non 0 value to add a port to the LAG. Values correspond to
ifIndex values in the ifTable.
Note: hmAgentPortType for the port to be added must be full duplex
and the same speed as previously added port(s), if any.rw Integer32 .1.3.6.1.4.1.248.15.1.2.2.2.1.7 |
hmAgentLagSummaryDeletePortAgent LAG DeletePort.
Set to a non 0 value to remove a port from the LAG. Values correspond to
ifIndex values in the ifTable.rw Integer32 .1.3.6.1.4.1.248.15.1.2.2.2.1.8 |
hmAgentLagSummaryStatusAgent LAG Status.
active(1) - This LAG is enabled.
destroy(6) - Set to this value to remove the LAG.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.248.15.1.2.2.2.1.9 |
hmAgentLagSummaryTypeAgent LAG Type.
static(1) - This LAG is staticly maintained.
dynamic(2) - This LAG is dynamicly maintained.ro Enumeration .1.3.6.1.4.1.248.15.1.2.2.2.1.10 |
hmAgentLagDetailedConfigTableA detailed table of the switch's LAG config entries SEQUENCE OF HmAgentLagDetailedConfigEntry .1.3.6.1.4.1.248.15.1.2.2.3 |
hmAgentLagDetailedConfigEntrySwitch's LAG config entry HmAgentLagDetailedConfigEntry .1.3.6.1.4.1.248.15.1.2.2.3.1 |
hmAgentLagDetailedLagIndexLAG indexro Integer32 .1.3.6.1.4.1.248.15.1.2.2.3.1.1 |
hmAgentLagDetailedIfIndexLAG port indexro Integer32 .1.3.6.1.4.1.248.15.1.2.2.3.1.2 |
hmAgentLagDetailedPortSpeedLAG port speed. See hmAgentPortType for a description and list
of valid values.ro OBJECT IDENTIFIER .1.3.6.1.4.1.248.15.1.2.2.3.1.3 |
hmAgentLagDetailedPortStatusLAG port status.
active(1) - Actively participating in the LAG.
inactive(2) - Not participating in the LAG.ro Enumeration .1.3.6.1.4.1.248.15.1.2.2.3.1.4 |
hmAgentLagConfigStaticCapabilityAgent LAG Static Capability.
Configures whether Static LAGs are supported on this device.rw Enumeration .1.3.6.1.4.1.248.15.1.2.2.4 |
hmAgentSpanningTreeConfigGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.15.1.2.7 |
hmAgentSpanningTreeModeThe switch's Spanning Tree Switch Statusrw Enumeration .1.3.6.1.4.1.248.15.1.2.7.1 |
hmAgentSwitchConfigGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.15.1.2.8 |
hmAgentSwitchBroadcastControlModeThe switch config broadcast allows you to enable or disable
broadcast storm recovery mode. When you specify Enable for Broadcast
Storm Recovery and the broadcast traffic on any Ethernet port exceeds
20 percent of the link speed, the switch blocks (discards) the broadcast
traffic until the broadcast traffic returns to 10 percent or less.
Upper limit for 10M link is 20% and lower limit is 10%.
For 100M link Upper limit is 5% and lower limit is 2%rw Enumeration .1.3.6.1.4.1.248.15.1.2.8.2 |
hmAgentSwitchDot3FlowControlModeConfig switchconfig flowcontrol allows you to enable or disable
802.3x flow control for the switch. This value
applies to only full-duplex mode ports.rw Enumeration .1.3.6.1.4.1.248.15.1.2.8.3 |
hmAgentSwitchAddressAgingTimeoutTableThe switch's address aging timeout table SEQUENCE OF HmAgentSwitchAddressAgingTimeoutEntry .1.3.6.1.4.1.248.15.1.2.8.4 |
hmAgentSwitchAddressAgingTimeoutEntryAging information about a specific Filtering Database. HmAgentSwitchAddressAgingTimeoutEntry .1.3.6.1.4.1.248.15.1.2.8.4.1 |
hmAgentSwitchAddressAgingTimeoutThe FDB entry's address aging timeout (in seconds)rw Integer32 .1.3.6.1.4.1.248.15.1.2.8.4.1.1 |
hmAgentSwitchStaticMacFilteringTableThe switch's static Mac filtering table SEQUENCE OF HmAgentSwitchStaticMacFilteringEntry .1.3.6.1.4.1.248.15.1.2.8.5 |
hmAgentSwitchStaticMacFilteringEntryPer-port ingress/egress filter configuration based on VLAN Id and MAC address. HmAgentSwitchStaticMacFilteringEntry .1.3.6.1.4.1.248.15.1.2.8.5.1 |
hmAgentSwitchStaticMacFilteringVlanIdThe Static MAC Filter Vlan Idro Integer32 .1.3.6.1.4.1.248.15.1.2.8.5.1.1 |
hmAgentSwitchStaticMacFilteringAddressThe Static MAC Filter MAC addressro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.248.15.1.2.8.5.1.2 |
hmAgentSwitchStaticMacFilteringSourcePortMaskThe Static MAC Filter source port mask.
When setting this value, the system will ignore configuration for ports not
between the first and last valid ports. Configuration of any port numbers
between this range that are not valid ports return a failure message, but will
still apply configuration for valid ports.
To obtain port numbers from interface numbers, use the objects
hmAgentPortDot1dBasePort and hmAgentPortIfIndex in the hmAgentPortConfigTable
table.rw HmAgentPortMask .1.3.6.1.4.1.248.15.1.2.8.5.1.3 |
hmAgentSwitchStaticMacFilteringDestPortMaskThe Static MAC Filter destination port mask.
When setting this value, the system will ignore configuration for ports not
between the first and last valid ports. Configuration of any port numbers
between this range that are not valid ports return a failure message, but will
still apply configuration for valid ports.
To obtain port numbers from interface numbers, use the objects
hmAgentPortDot1dBasePort and hmAgentPortIfIndex in the hmAgentPortConfigTable
table.rw HmAgentPortMask .1.3.6.1.4.1.248.15.1.2.8.5.1.4 |
hmAgentSwitchStaticMacFilteringStatusThe Static MAC Filter status.
Supported values:
active(1) - valid entry
createAndGo(4) - used to create a new entry
destroy(6) - removes the entryrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.248.15.1.2.8.5.1.5 |
hmAgentSwitchIGMPSnoopingGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.15.1.2.8.6 |
hmAgentSwitchIGMPSnoopingAdminModeThis enables or disables IGMP Snooping on the system.rw Enumeration .1.3.6.1.4.1.248.15.1.2.8.6.1 |
hmAgentSwitchIGMPSnoopingGroupMembershipIntervalThe amount of time in seconds a switch will wait for a report
for a particular group on a particular interface before
it deletes the interface from the entry.rw Integer32 .1.3.6.1.4.1.248.15.1.2.8.6.2 |
hmAgentSwitchIGMPSnoopingMaxResponseTimeThe amount of time in seconds a switch will wait after sending
a query on an interface because it did not receive a report for
a particular group in that interface. This value must be less
than hmAgentSwitchIGMPSnoopingQueryInterval.rw Integer32 .1.3.6.1.4.1.248.15.1.2.8.6.3 |
hmAgentSwitchIGMPSnoopingMRPExpirationTimeMulticast Router Present Expiration Time.
The amount of time in seconds a switch will wait for a query to
be received on an interface before the interface is removed from
the list of interfaces with mutlticast routers attached. A value
of zero indicates an infinite timeout, i.e. the entries in the list
will not expire.rw Integer32 .1.3.6.1.4.1.248.15.1.2.8.6.4 |
hmAgentSwitchIGMPSnoopingPortMaskIGMP Snooping Port Mask.
This allows configuration of IGMP Snooping on selected ports.
IGMP Snooping cannot be enabled on an interface that has routing
enabled, or is a member of a LAG. If a port which has IGMP Snooping
enabled becomes enabled for routing, or is enlisted as a member of a
LAG, IGMP Snooping functionality will be disabled on that port. IGMP
Snooping functionality will be subsequently be reenabled if routing is
disabled or LAG membership is removed from an interface that had previously
had IGMP Snooping enabled.
To obtain port numbers from interface numbers, use the objects
hmAgentPortDot1dBasePort and hmAgentPortIfIndex in the hmAgentPortConfigTable
table.rw HmAgentPortMask .1.3.6.1.4.1.248.15.1.2.8.6.5 |
hmAgentSwitchIGMPSnoopingMulticastControlFramesProcessedMulticast Control Frames Processed by CPU.
The number of multicast control frames that have been processed by the CPU.ro Counter32 .1.3.6.1.4.1.248.15.1.2.8.6.6 |
hmAgentSwitchMFDBGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.15.1.2.8.7 |
hmAgentSwitchMFDBTableThe Multicast Forwarding Database table SEQUENCE OF HmAgentSwitchMFDBEntry .1.3.6.1.4.1.248.15.1.2.8.7.1 |
hmAgentSwitchMFDBEntryContains Forwarding and Filtering information per Vlan Index, MAC Address, and
Component User. HmAgentSwitchMFDBEntry .1.3.6.1.4.1.248.15.1.2.8.7.1.1 |
hmAgentSwitchMFDBVlanIdVlan Index for which this entry is associated with.ro VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.248.15.1.2.8.7.1.1.1 |
hmAgentSwitchMFDBMacAddressA multicast MAC address for which the switch has forwarding and or
filtering information.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.248.15.1.2.8.7.1.1.2 |
hmAgentSwitchMFDBProtocolTypeThe component that is responsible for this entry in the Multicast
Forwarding Database.ro Enumeration .1.3.6.1.4.1.248.15.1.2.8.7.1.1.3 |
hmAgentSwitchMFDBTypeThis displays the type of the entry.
static(1) - Entries configured by the end user
dynamic(2) - Entries added as a result of a learning process or protocolro Enumeration .1.3.6.1.4.1.248.15.1.2.8.7.1.1.4 |
hmAgentSwitchMFDBDescriptionText description of this multicast table entry.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.248.15.1.2.8.7.1.1.5 |
hmAgentSwitchMFDBForwardingPortMaskBitMask indicating which ports this entry indicates should be forwarded.
To obtain port numbers from interface numbers, use the objects
hmAgentPortDot1dBasePort and hmAgentPortIfIndex in the hmAgentPortConfigTable
table.ro HmAgentPortMask .1.3.6.1.4.1.248.15.1.2.8.7.1.1.6 |
hmAgentSwitchMFDBFilteringPortMaskBitMask indicating which ports this entry indicates should be filtered.
To obtain port numbers from interface numbers, use the objects
hmAgentPortDot1dBasePort and hmAgentPortIfIndex in the hmAgentPortConfigTable
table.ro HmAgentPortMask .1.3.6.1.4.1.248.15.1.2.8.7.1.1.7 |
hmAgentSwitchMFDBSummaryTableThe Multicast Forwarding Database Summary table SEQUENCE OF HmAgentSwitchMFDBSummaryEntry .1.3.6.1.4.1.248.15.1.2.8.7.2 |
hmAgentSwitchMFDBSummaryEntrySummarizes the forwarding ports for all components registered for all
MFDB table entries with the same Vlan Index and MAC Address. HmAgentSwitchMFDBSummaryEntry .1.3.6.1.4.1.248.15.1.2.8.7.2.1 |
hmAgentSwitchMFDBSummaryVlanIdVlan Index for which this entry is associated with.ro VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.248.15.1.2.8.7.2.1.1 |
hmAgentSwitchMFDBSummaryMacAddressA multicast MAC address for which the switch has forwarding and or
filtering information.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.248.15.1.2.8.7.2.1.2 |
hmAgentSwitchMFDBSummaryForwardingPortMaskPort Mask indicating which ports this entry indicates should be forwarded.
To obtain port numbers from interface numbers, use the objects
hmAgentPortDot1dBasePort and hmAgentPortIfIndex in the hmAgentPortConfigTable
table.ro HmAgentPortMask .1.3.6.1.4.1.248.15.1.2.8.7.2.1.3 |
hmAgentSwitchMFDBMaxTableEntriesThis displays the maximum number of entries that can possibly be in
the Multicast Forwarding Database table.ro Gauge32 .1.3.6.1.4.1.248.15.1.2.8.7.3 |
hmAgentSwitchMFDBMostEntriesUsedThis displays the largest number of entries that have been present
in the Multicast Forwarding Database table. This value is also known
as the MFDB high-water mark.ro Gauge32 .1.3.6.1.4.1.248.15.1.2.8.7.4 |
hmAgentSwitchMFDBCurrentEntriesThis displays the current number of entries in the Multicast
Forwarding Database table.ro Gauge32 .1.3.6.1.4.1.248.15.1.2.8.7.5 |
hmAgentSwitchDVlanTagGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.15.1.2.8.8 |
hmAgentSwitchDVlanTagEthertypeConfigures the Double Vlan Tag Ethertype for the switch.
If this object is supported, ethertype cannot be
configured per port.
Commonly used are the Ethertypes for vman tags (34984, or 0x88A8)
and dot1q tags (33024, or 0x8100).rw Integer32 .1.3.6.1.4.1.248.15.1.2.8.8.1 |
hmAgentSwitchVoiceVLANGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.15.1.2.8.25 |
hmAgentSwitchVoiceVLANAdminModeThis enables or disables Voice VLAN on the system.rw Enumeration .1.3.6.1.4.1.248.15.1.2.8.25.1 |
hmAgentSwitchVoiceVlanDeviceTableA table of the Voice Vlan device entries. SEQUENCE OF HmAgentSwitchVoiceVlanDeviceEntry .1.3.6.1.4.1.248.15.1.2.8.25.2 |
hmAgentSwitchVoiceVlanDeviceEntryRepresents entry for a Voice Device on the interface. HmAgentSwitchVoiceVlanDeviceEntry .1.3.6.1.4.1.248.15.1.2.8.25.2.1 |
hmAgentSwitchVoiceVlanInterfaceNumThe interface number of this interface.ro Integer32 .1.3.6.1.4.1.248.15.1.2.8.25.2.1.1 |
hmAgentSwitchVoiceVlanDeviceMacAddressThe Voice Device Mac addressro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.248.15.1.2.8.25.2.1.2 |
hmAgentTransferConfigGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.15.1.2.9 |
hmAgentTransferUploadGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.15.1.2.9.1 |
hmAgentTransferUploadModeTransfer upload mode configures the mode to use when uploading from the
switch. The mode is either X/Y/ZMODEM or TFTP. X/Y/ZMODEM is valid only when the
file transfer is initiated by the serial EIA 232 port.rw Enumeration .1.3.6.1.4.1.248.15.1.2.9.1.1 |
hmAgentTransferUploadServerIPTransfer upload tftpserverip configures the IP address of the server
where the file is located. It is valid only when the Transfer Mode is
TFTP. The address is 4 integer bytes ranging from 0 to 255.rw IpAddress .1.3.6.1.4.1.248.15.1.2.9.1.2 |
hmAgentTransferUploadPathTransfer upload tftppath configures the directory path where the file
is to be uploaded to. The switch remembers the last file path used.rw DisplayString .1.3.6.1.4.1.248.15.1.2.9.1.3 |
hmAgentTransferUploadFilenameTransfer upload tftpfilename configures the file name for the file being
uploaded from the switch. It can be up to 32 alphanumeric characters.
The switch remembers the last file name used.
File path can be appended to the file name if the string is less than 17
characters. Otherwise, the File Path field will need to be used and the
File Name will be appended to the File Path as is. An example would be
File Path set to c:/tftp/code/ and File Name set to e1r1v1.opr.
Note: File Name, File Path, and TFTP Server IP Address are applicable
only if the Transfer Mode is TFTP.rw DisplayString .1.3.6.1.4.1.248.15.1.2.9.1.4 |
hmAgentTransferUploadDataTypeTransfer upload datatype configures the type of file to upload from the
switch.
The types for upload are:
- Configuration File
- Error log
- Message log
- Trap logrw Enumeration .1.3.6.1.4.1.248.15.1.2.9.1.5 |
hmAgentTransferUploadStartTransfer upload start will start an upload transfer.
The hmAgentTransferUploadMode object must not be set to xmodem(2),
ymodem(3), or zmodem(4) to initiate a transfer via SNMP.rw Enumeration .1.3.6.1.4.1.248.15.1.2.9.1.6 |
hmAgentTransferUploadStatusIndicates the current status of an upload transfer.ro Enumeration .1.3.6.1.4.1.248.15.1.2.9.1.7 |
hmAgentTransferDownloadGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.15.1.2.9.2 |
hmAgentTransferDownloadModeTransfer download mode configures the mode to use when downloading
to the switch. The mode is either X/Y/ZMODEM or TFTP. X/Y/ZMODEM is valid only
when the file transfer is initiated by the serial EIA 232 port.rw Enumeration .1.3.6.1.4.1.248.15.1.2.9.2.1 |
hmAgentTransferDownloadServerIPTransfer download tftpserverip configures the IP address of the server
where the file is located. It is valid only when the Transfer Mode is TFTP.
The address is 4 integer bytes ranging from 0 to 255.rw IpAddress .1.3.6.1.4.1.248.15.1.2.9.2.2 |
hmAgentTransferDownloadPathTransfer download tftppath configures the directory path where the
file is located. The switch remembers the last file path used.rw DisplayString .1.3.6.1.4.1.248.15.1.2.9.2.3 |
hmAgentTransferDownloadFilenameTransfer download tftpfilename configures the file name for the file
being downloaded to the switch. It can be up to 32 alphanumeric characters.
The switch remembers the last file name used.
File path can be appended to the file name if the string is less than 33
characters. Otherwise, the File Path field will need to be used and the
File Name will be appended to the File Path as is. An example would be
File Path set to c:/tftp/code/ and File Name set to e1r1v1.opr.
Note: File Name, File Path, and TFTP Server IP Address are applicable
only if the Transfer Mode is TFTP.rw DisplayString .1.3.6.1.4.1.248.15.1.2.9.2.4 |
hmAgentTransferDownloadDataTypeTransfer download datatype configures the type of file to download to
the switch.
The types for download are:
code - Code File
config - Configuration Filerw Enumeration .1.3.6.1.4.1.248.15.1.2.9.2.5 |
hmAgentTransferDownloadStartTransfer download start will start an download transfer.
The hmAgentTransferDownloadMode object must not be set to xmodem(2),
ymodem(3), or zmodem(4) to initiate a transfer via SNMP.rw Enumeration .1.3.6.1.4.1.248.15.1.2.9.2.6 |
hmAgentTransferDownloadStatusIndicates the current status of an download transfer.ro Enumeration .1.3.6.1.4.1.248.15.1.2.9.2.7 |
hmAgentPortMirroringGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.15.1.2.10 |
hmAgentMirroredPortIfIndexIfIndex of the mirrored portrwobsolete Integer32 .1.3.6.1.4.1.248.15.1.2.10.1 |
hmAgentProbePortIfIndexIfIndex of the probe portrwobsolete Integer32 .1.3.6.1.4.1.248.15.1.2.10.2 |
hmAgentPortMirroringModePort mirroring mode:
enable - enable mirroring mode
disable - disable mirroring mode
delete - clear MirroredPort and Probe Port configurationrwobsolete Enumeration .1.3.6.1.4.1.248.15.1.2.10.3 |
hmAgentPortMirrorTableThis table includes entries for each Port Mirroring session. SEQUENCE OF HmAgentPortMirrorEntry .1.3.6.1.4.1.248.15.1.2.10.4 |
hmAgentPortMirrorEntryProvides configuration of a Port Mirroring session specifying the
destination port, and the source Port Mask, providing a many-to-one
mapping. HmAgentPortMirrorEntry .1.3.6.1.4.1.248.15.1.2.10.4.1 |
hmAgentPortMirrorSessionNumThe Session number of this mirroring entry. The number of sessions is
fixed, and is platform dependant. Unsigned32 .1.3.6.1.4.1.248.15.1.2.10.4.1.1 |
hmAgentPortMirrorDestinationPortThe port which traffic from the mirrored ports will be sent to.rw Unsigned32 .1.3.6.1.4.1.248.15.1.2.10.4.1.2 |
hmAgentPortMirrorSourcePortMaskThe ports from which traffic will be sent to the destination port.
The destination port can not be included in this list of ports.rw HmAgentPortMask .1.3.6.1.4.1.248.15.1.2.10.4.1.3 |
hmAgentPortMirrorAdminModeThe status of this port mirroring session.
enable(1) - This session is active and all traffic from the source ports
will be mirrored to the destination port.
disable(2) - This session is not active.
delete(3) - Remove the configuration for this Sessionrw Enumeration .1.3.6.1.4.1.248.15.1.2.10.4.1.4 |
hmAgentPortMirrorIngressMaskThe ports from which ingress traffic will be mirrored.rw HmAgentPortMask .1.3.6.1.4.1.248.15.1.2.10.4.1.248 |
hmAgentPortMirrorEgressMaskThe ports from which egress traffic will be mirrored.rw HmAgentPortMask .1.3.6.1.4.1.248.15.1.2.10.4.1.249 |
hmAgentDot3adAggPortTableThis table provides 802.3ad link aggregation information for each
physical port that is not available through the standard MIB. SEQUENCE OF HmAgentDot3adAggPortEntry .1.3.6.1.4.1.248.15.1.2.12 |
hmAgentDot3adAggPortEntryInformation about a table entry. The hmAgentDot3adAggPort identifies
the external interface number of the port. HmAgentDot3adAggPortEntry .1.3.6.1.4.1.248.15.1.2.12.1 |
hmAgentDot3adAggPortifIndex of this physical portro Integer32 .1.3.6.1.4.1.248.15.1.2.12.1.1 |
hmAgentDot3adAggPortLACPModeEnable/disable 802.3ad LACP on this portrw Enumeration .1.3.6.1.4.1.248.15.1.2.12.1.2 |
hmAgentPortConfigTableA table of the switch's physical port config entries SEQUENCE OF HmAgentPortConfigEntry .1.3.6.1.4.1.248.15.1.2.13 |
hmAgentPortConfigEntrySwitch's physical port config entry HmAgentPortConfigEntry .1.3.6.1.4.1.248.15.1.2.13.1 |
hmAgentPortDot1dBasePortThe port number of this port.ro Integer32 .1.3.6.1.4.1.248.15.1.2.13.1.1 |
hmAgentPortIfIndexThe switch's Port IfIndexro Integer32 .1.3.6.1.4.1.248.15.1.2.13.1.2 |
hmAgentPortIanaTypeThe switch's Port Typero IANAifType (IANAifType-MIB) .1.3.6.1.4.1.248.15.1.2.13.1.3 |
hmAgentPortSTPModeThe switch's Port Spanning Tree Protocol Mode
STP mode values are:
dot1d (the default)
fast, indicates you want to use the fast spanning tree mode
off, indicates the STP mode is turned off for a particular port
This object is only supported when the Dot1d Protocol is enabled.rw Enumeration .1.3.6.1.4.1.248.15.1.2.13.1.4 |
hmAgentPortSTPStateThe switch's Port Spanning Tree Protocol State.
This object is only supported when the Dot1d Protocol is enabled.ro Enumeration .1.3.6.1.4.1.248.15.1.2.13.1.5 |
hmAgentPortAdminModeThe switch's Port Admin Moderw Enumeration .1.3.6.1.4.1.248.15.1.2.13.1.6 |
hmAgentPortPhysicalModeThe switch's Port Speed Mode. This is the configured physical mode.
This object is read-only for gigabit portsrwobsolete Enumeration .1.3.6.1.4.1.248.15.1.2.13.1.7 |
hmAgentPortPhysicalStatusThe switch's Port Physical Speed Status. This is the current actual speed.roobsolete Enumeration .1.3.6.1.4.1.248.15.1.2.13.1.8 |
hmAgentPortLinkTrapModeIf enabled, link up and link down traps will be sent for this port.rw Enumeration .1.3.6.1.4.1.248.15.1.2.13.1.9 |
hmAgentPortClearStatsclear stats for this port onlyrw Enumeration .1.3.6.1.4.1.248.15.1.2.13.1.10 |
hmAgentPortDefaultTypeThis object identifies the default administrative port type,
to be used in conjunction with the operational port type
denoted by hmAgentPortType.
The set of possible values for this object is
the same as the set defined for the hmAgentPortType
object.
This object represents the administratively-configured type of
the MAU. If auto-negotiation is not enabled or is not
implemented for this MAU, the value of this object determines
the operational type of the MAU. In this case, a set to this
object will force the MAU into the specified operating mode.
If auto-negotiation is implemented and enabled for this MAU,
the operational type of the MAU is determined by auto-negotiation,
and the value of this object denotes the type to which the MAU
will automatically revert if/when auto-negotiation is later disabled.
The valid values for this object are:
dot3MauType10BaseTHD
dot3MauType10BaseTFD
dot3MauType100BaseTXHD
dot3MauType100BaseTXFD
dot3MauType100BaseFXFD
dot3MauType1000BaseSXFDrw OBJECT IDENTIFIER .1.3.6.1.4.1.248.15.1.2.13.1.11 |
hmAgentPortTypeThis object identifies the port type. An initial set of MAU types
are defined in RFC 2668. The assignment of OBJECT IDENTIFIERs to
new types of MAUs is managed by the IANA. If the MAU type is
unknown, the object identifier
unknownMauType OBJECT IDENTIFIER ::= { 0 0 }
is returned. Note that unknownMauType is a syntactically valid
object identifier, and any conformant implementation of ASN.1 and
the BER must be able to generate and recognize this value.
This object represents the operational type of the MAU, as determined
by either (1) the result of the auto-negotiation function or (2) if
auto-negotiation is not enabled or is not implemented for this MAU,
by the value of the object hmAgentPortDefaultType, or (3) for the GigE card
a value determined by the GBIC connected to the card. In case (2), a
set to the object hmAgentPortDefaultType will force the MAU into the
new operating mode.
The valid values for this object are:
dot3MauType10BaseTHD
dot3MauType10BaseTFD
dot3MauType100BaseTXHD
dot3MauType100BaseTXFD
dot3MauType100BaseFXFD
dot3MauType1000BaseSXFD
dot3MauType1000BaseTFDro OBJECT IDENTIFIER .1.3.6.1.4.1.248.15.1.2.13.1.12 |
hmAgentPortAutoNegAdminStatusThis object identifies the administration status of auto negotiation
for this port.rw Enumeration .1.3.6.1.4.1.248.15.1.2.13.1.13 |
hmAgentPortDot3FlowControlModeConfig flowcontrol allows you to enable or disable
802.3x flow control for this port. This value
applies to only full-duplex mode ports.rw Enumeration .1.3.6.1.4.1.248.15.1.2.13.1.14 |
hmAgentPortDVlanTagModeControls the Double Vlan Tag mode on this port.
Default is normal(2).rw Enumeration .1.3.6.1.4.1.248.15.1.2.13.1.15 |
hmAgentPortDVlanTagEthertypeConfigures the Double Vlan Tag Ethertype for this port.
If this object is supported, ethertype cannot be configured
globally for the switch.
Commonly used are the Ethertypes for vman tags (34984, or 0x88A8)
and dot1q tags (33024, or 0x8100).rw Integer32 .1.3.6.1.4.1.248.15.1.2.13.1.16 |
hmAgentPortDVlanTagCustomerIdConfigures the Customer ID for the Double Vlan Tag for this port.rw Integer32 .1.3.6.1.4.1.248.15.1.2.13.1.17 |
hmAgentPortMaxFrameSizeLimitThis object identifies the largest value that can be
configured for hmAgentPortMaxFrameSizero Integer32 .1.3.6.1.4.1.248.15.1.2.13.1.18 |
hmAgentPortMaxFrameSizeThis object identifies the currently configured maximum frame size
value for this port. The maximmum value that this object can be set
to is the value of hmAgentPortMaxFrameSizeLimit. For Ethernet ports
which support 802.1Q vlan tagging, the minimum value that this object
can be set to is 1522rw Integer32 .1.3.6.1.4.1.248.15.1.2.13.1.19 |
hmAgentPortVoiceVlanModeDescribes and Configures the Port Voice VLAN Mode.rw Enumeration .1.3.6.1.4.1.248.15.1.2.13.1.20 |
hmAgentPortVoiceVlanIDDescribes and Configures the Port Voice VLAN ID
if the Voice Vlan Mode is Vlan ID.rw Integer32 .1.3.6.1.4.1.248.15.1.2.13.1.21 |
hmAgentPortVoiceVlanPriorityDescribes and Configures the Port Voice VLAN Priority
if the Voice Vlan Mode is dot1p. A value of 255 indicates
that the priority is not configured.rw INTEGER (0..7|255) .1.3.6.1.4.1.248.15.1.2.13.1.22 |
hmAgentPortVoiceVlanDataPriorityModeDescribes and Configures the Port Voice VLAN Data Priority Mode.rw Enumeration .1.3.6.1.4.1.248.15.1.2.13.1.23 |
hmAgentPortVoiceVlanOperationalStatusDescribes the Port Voice VLAN Operational Status.ro Enumeration .1.3.6.1.4.1.248.15.1.2.13.1.24 |
hmAgentPortVoiceVlanDSCPDescribes and Configures the Port Voice VLAN DSCP value.rw Integer32 .1.3.6.1.4.1.248.15.1.2.13.1.25 |
hmAgentPortVoiceVlanAuthModeDescribes and Configures the Port Voice VLAN Authentication mode.
Disable means authentication not required for voice devices when dot1x is enabled.rw Enumeration .1.3.6.1.4.1.248.15.1.2.13.1.26 |
hmAgentProtocolConfigGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.15.1.2.14 |
hmAgentProtocolGroupCreateSet to non-empty string to create a Protocol-Based VLAN group.rw DisplayString .1.3.6.1.4.1.248.15.1.2.14.1 |
hmAgentProtocolGroupTableA table of the switch's Protocol-based VLAN entries SEQUENCE OF HmAgentProtocolGroupEntry .1.3.6.1.4.1.248.15.1.2.14.2 |
hmAgentProtocolGroupEntrySwitch's Protocol-based VLAN entry HmAgentProtocolGroupEntry .1.3.6.1.4.1.248.15.1.2.14.2.1 |
hmAgentProtocolGroupIdGroup identifier of the Protocol-based VLAN entry.ro Integer32 .1.3.6.1.4.1.248.15.1.2.14.2.1.1 |
hmAgentProtocolGroupNameGroup name of the Protocol-based VLAN entry.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.248.15.1.2.14.2.1.2 |
hmAgentProtocolGroupVlanIdVLAN associated with the Protocol-based VLAN entry. Set to 0 to remove.rw Integer32 .1.3.6.1.4.1.248.15.1.2.14.2.1.3 |
hmAgentProtocolGroupProtocolIPThe status of the IP protocol association with the Protocol-based VLAN entry.rw Enumeration .1.3.6.1.4.1.248.15.1.2.14.2.1.4 |
hmAgentProtocolGroupProtocolARPThe status of the ARP protocol association with the Protocol-based VLAN entry.rw Enumeration .1.3.6.1.4.1.248.15.1.2.14.2.1.5 |
hmAgentProtocolGroupProtocolIPXThe status of the IPX protocol association with the Protocol-based VLAN entry.rw Enumeration .1.3.6.1.4.1.248.15.1.2.14.2.1.6 |
hmAgentProtocolGroupStatusThe status of the Protocol-based VLAN entry.
active(1) - this entry is active
destroy(6) - remove this entryrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.248.15.1.2.14.2.1.7 |
hmAgentProtocolGroupPortTableA table of the switch's physical port config entries SEQUENCE OF HmAgentProtocolGroupPortEntry .1.3.6.1.4.1.248.15.1.2.14.3 |
hmAgentProtocolGroupPortEntrySwitch's physical port config entry HmAgentProtocolGroupPortEntry .1.3.6.1.4.1.248.15.1.2.14.3.1 |
hmAgentProtocolGroupPortIfIndexThe interface number of this instance.ro Integer32 .1.3.6.1.4.1.248.15.1.2.14.3.1.1 |
hmAgentProtocolGroupPortStatusThe status of this entry.
active(1) - the port is associated with this group
createAndGo(4) - add the port to this group
createAndWait(5) - add the port to this group
destroy(6) - remove the port from this grouprw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.248.15.1.2.14.3.1.2 |
hmAgentStpSwitchConfigGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.15.1.2.15 |
hmAgentStpConfigDigestKeyThe MST configuration digest key.ro OCTET STRING .1.3.6.1.4.1.248.15.1.2.15.1 |
hmAgentStpConfigFormatSelectorThe MST configuration format selector. A value other than 0 (zero)
indicates non-support for the IEEE 802.1s standard.ro Unsigned32 .1.3.6.1.4.1.248.15.1.2.15.2 |
hmAgentStpConfigNameThe MST configuration name of at most 32 characters.rw DisplayString .1.3.6.1.4.1.248.15.1.2.15.3 |
hmAgentStpConfigRevisionThe MST configuration revision. The default value is 1.rw Unsigned32 .1.3.6.1.4.1.248.15.1.2.15.4 |
hmAgentStpForceVersionThe MST configuration force protocol version. The default version is dot1w.rw Enumeration .1.3.6.1.4.1.248.15.1.2.15.5 |
hmAgentStpAdminModeThe spanning tree operational status.
enable(1) - enables spanning tree operational status on the switch.
disable(2) - disables spanning tree operational status on the switch.
The default status is enabled.rw Enumeration .1.3.6.1.4.1.248.15.1.2.15.6 |
hmAgentStpPortTableSTP port table. SEQUENCE OF HmAgentStpPortEntry .1.3.6.1.4.1.248.15.1.2.15.7 |
hmAgentStpPortEntrySTP port entry. HmAgentStpPortEntry .1.3.6.1.4.1.248.15.1.2.15.7.1 |
hmAgentStpPortStateThe administrative STP state for the port.
enable(1) - enables STP on the port.
disable(2) - disables STP on the port.
The default port STP state is enabled for the first 4095
ports and disabled for any ports beyond.rw Enumeration .1.3.6.1.4.1.248.15.1.2.15.7.1.1 |
hmAgentStpPortStatsMstpBpduRxThe MSTP BPDUs received on a specific port.ro Counter32 .1.3.6.1.4.1.248.15.1.2.15.7.1.2 |
hmAgentStpPortStatsMstpBpduTxThe MSTP BPDUs sent from a specific port.ro Counter32 .1.3.6.1.4.1.248.15.1.2.15.7.1.3 |
hmAgentStpPortStatsRstpBpduRxThe RSTP BPDUs received on a specific port.ro Counter32 .1.3.6.1.4.1.248.15.1.2.15.7.1.4 |
hmAgentStpPortStatsRstpBpduTxThe RSTP BPDUs sent from a specific port.ro Counter32 .1.3.6.1.4.1.248.15.1.2.15.7.1.5 |
hmAgentStpPortStatsStpBpduRxThe STP BPDUs received on a specific port.ro Counter32 .1.3.6.1.4.1.248.15.1.2.15.7.1.6 |
hmAgentStpPortStatsStpBpduTxThe STP BPDUs sent from a specific port.ro Counter32 .1.3.6.1.4.1.248.15.1.2.15.7.1.7 |
hmAgentStpPortUpTimeTime since port was reset.
It is displayed in days, hours, minutes, and seconds.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.248.15.1.2.15.7.1.8 |
hmAgentStpPortMigrationCheckForce the specified port to transmit RSTP or MSTP BPDU's.
Supported values:
false(0) - BPDUs are not to be transmitted.
true(1) - BPDUs are to be transmitted
A non-zero value indicates that BPDUs are to be sent on the specified port.rw Enumeration .1.3.6.1.4.1.248.15.1.2.15.7.1.9 |
hmAgentStpPortHelloTimeHello time for the STP port. The default value is 2.rw Unsigned32 .1.3.6.1.4.1.248.15.1.2.15.7.1.10 |
hmAgentStpCstConfigGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.15.1.2.15.8 |
hmAgentStpCstHelloTimeThe MSTP root port hello time for the CIST.ro Unsigned32 .1.3.6.1.4.1.248.15.1.2.15.8.1 |
hmAgentStpCstMaxAgeThe MSTP root port max age for the CIST.ro Unsigned32 .1.3.6.1.4.1.248.15.1.2.15.8.2 |
hmAgentStpCstRegionalRootIdThe MSTP regional root identifier for the CIST.ro OCTET STRING .1.3.6.1.4.1.248.15.1.2.15.8.3 |
hmAgentStpCstRegionalRootPathCostThe MSTP regional root path cost for the CIST.ro Unsigned32 .1.3.6.1.4.1.248.15.1.2.15.8.4 |
hmAgentStpCstRootFwdDelayThe MSTP root port forward delay for the CIST.ro Unsigned32 .1.3.6.1.4.1.248.15.1.2.15.8.5 |
hmAgentStpCstBridgeFwdDelayThe MSTP bridge forward delay for the CIST. The default value is 15.rw Unsigned32 .1.3.6.1.4.1.248.15.1.2.15.8.6 |
hmAgentStpCstBridgeHelloTimeThe MSTP bridge hello time for the CIST. The default value is 2.rw Unsigned32 .1.3.6.1.4.1.248.15.1.2.15.8.7 |
hmAgentStpCstBridgeHoldTimeThe MSTP bridge hold time for the CIST.ro Unsigned32 .1.3.6.1.4.1.248.15.1.2.15.8.8 |
hmAgentStpCstBridgeMaxAgeThe MSTP bridge max age for the CIST. The default value is 20.rw Unsigned32 .1.3.6.1.4.1.248.15.1.2.15.8.9 |
hmAgentStpCstBridgeDesignatedRootThe Designated Root like in dot1dStpDesignatedRoot.ro BridgeId .1.3.6.1.4.1.248.15.1.2.15.8.10 |
hmAgentStpCstBridgePriorityThe MSTP bridge priority for the CIST. The default value is 32768.rw Unsigned32 .1.3.6.1.4.1.248.15.1.2.15.8.11 |
hmAgentStpCstBridgeTimeSinceTopologyChangeThe time (in hundredths of a second) since the
last time a topology change was detected by the
bridge entity.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.248.15.1.2.15.8.12 |
hmAgentStpCstBridgeTopChangesThe total number of topology changes detected by
this bridge since the management entity was last
reset or initialized.ro Counter32 .1.3.6.1.4.1.248.15.1.2.15.8.13 |
hmAgentStpCstBridgeRootCostThe cost of the path to the root as seen from
this bridge.ro Unsigned32 .1.3.6.1.4.1.248.15.1.2.15.8.14 |
hmAgentStpCstBridgeRootPortThe port number of the port which offers the
lowest cost path from this bridge to the root
bridge.ro Unsigned32 .1.3.6.1.4.1.248.15.1.2.15.8.15 |
hmAgentStpCstBridgeMaxHopsThe MSTP bridge max hops for the CIST. The default value is 20.rw Unsigned32 .1.3.6.1.4.1.248.15.1.2.15.8.16 |
hmAgentStpCstBridgeHoldCountThe MSTP bridge hold count for the CIST. This command sets the value of
maximum bpdus that a bridge is allowed to send within a hello time window.
The default value is 10.rw Unsigned32 .1.3.6.1.4.1.248.15.1.2.15.8.17 |
hmAgentStpCstPortTableCIST port table. SEQUENCE OF HmAgentStpCstPortEntry .1.3.6.1.4.1.248.15.1.2.15.9 |
hmAgentStpCstPortEntryCIST port entry. HmAgentStpCstPortEntry .1.3.6.1.4.1.248.15.1.2.15.9.1 |
hmAgentStpCstPortOperEdgeThe MSTP operational status of a specific port for the CIST.ro Enumeration .1.3.6.1.4.1.248.15.1.2.15.9.1.1 |
hmAgentStpCstPortOperPointToPointThe MSTP operational point to point mac of a specific port for the CIST.ro Enumeration .1.3.6.1.4.1.248.15.1.2.15.9.1.2 |
hmAgentStpCstPortTopologyChangeAckThe MSTP topology change acknowledge for a specific port in the CIST.ro Enumeration .1.3.6.1.4.1.248.15.1.2.15.9.1.3 |
hmAgentStpCstPortEdgeThe administrative state of a specific port in CIST.
true(1) - port is edge port.
false(2) - port is auto-edge or no edge port.
The default port state is disabled.rw Enumeration .1.3.6.1.4.1.248.15.1.2.15.9.1.4 |
hmAgentStpCstPortForwardingStateThe MSTP forwarding state of a specific port in CIST.ro Enumeration .1.3.6.1.4.1.248.15.1.2.15.9.1.5 |
hmAgentStpCstPortIdThe MSTP port identifier of a specific port in CIST.ro OCTET STRING .1.3.6.1.4.1.248.15.1.2.15.9.1.6 |
hmAgentStpCstPortPathCostThe MSTP port path cost in CIST. The default value will
correspond to the recommendation specified in IEEE 802.1s Table 13-2
which varies depending upon link speed.rw Unsigned32 .1.3.6.1.4.1.248.15.1.2.15.9.1.7 |
hmAgentStpCstPortPriorityThe MSTP port priority in CIST. The priority is
in the increments of 16. The default value is 128.rw Unsigned32 .1.3.6.1.4.1.248.15.1.2.15.9.1.8 |
hmAgentStpCstDesignatedBridgeIdThe MSTP designated bridge ID of a specific port in CIST.ro OCTET STRING .1.3.6.1.4.1.248.15.1.2.15.9.1.9 |
hmAgentStpCstDesignatedCostThe MSTP designated cost of a specific port in CIST.ro Unsigned32 .1.3.6.1.4.1.248.15.1.2.15.9.1.10 |
hmAgentStpCstDesignatedPortIdThe MSTP designated port ID of a specific port in CIST.ro OCTET STRING .1.3.6.1.4.1.248.15.1.2.15.9.1.11 |
hmAgentStpCstExtPortPathCostThe MSTP external port path cost in CIST. The default value varies depending upon the link speed.rw Unsigned32 .1.3.6.1.4.1.248.15.1.2.15.9.1.12 |
hmAgentStpCstPortAutoEdgeThe auto edge state of a specific port in CIST.
true(1) - enables the port.
false(2) - disables the port.
The default port state is enabled.rw Enumeration .1.3.6.1.4.1.248.15.1.2.15.9.1.13 |
hmAgentStpCstPortRoleThe current Port Role for the Port (i.e., Root, Alternate,
Designated, or Backup), for the CIST.ro Enumeration .1.3.6.1.4.1.248.15.1.2.15.9.1.14 |
hmAgentStpCstPortDisputedThe current value of the disputed variable for the CIST for
the Port. A value of true(1) indicates that the disputed
variable is set. A value of false(2) indicates that the
agreed variable is cleared.ro Enumeration .1.3.6.1.4.1.248.15.1.2.15.9.1.15 |
hmAgentStpCstPortBpduGuardEffectBPDU Guard Mode effect on the port.
enable(1) - BPDU Guard Mode is enabled on the port.
disable(2) - BPDU Guard Mode is disabled on the port.ro Enumeration .1.3.6.1.4.1.248.15.1.2.15.9.1.16 |
hmAgentStpCstPortBpduFilterThis command sets BPDU Filter mode on the port.
enable(1) - BPDU Filter Mode is enabled on the port.
disable(2) - BPDU Filter Mode is disabled on the port.rw Enumeration .1.3.6.1.4.1.248.15.1.2.15.9.1.17 |
hmAgentStpCstPortBpduFloodThis command sets BPDU Flood mode on the port.
enable(1) - BPDU Flood Mode is enabled on the port.
disable(2) - BPDU Flood Mode is disabled on the port.rw Enumeration .1.3.6.1.4.1.248.15.1.2.15.9.1.18 |
hmAgentStpCstPortRootGuardThis command sets a port to discard any superior information
received by the port and thus protect against root of the device
from changing.The port gets put into discarding state and does
not forward any packets.
enable(1) - enables the root-guard mode for the port.
disable(2) - disables the root-guard mode for the port.
The default root-guard mode is disabled.rw Enumeration .1.3.6.1.4.1.248.15.1.2.15.9.1.19 |
hmAgentStpCstPortTCNGuardThis command restricts the port from propagating any topology change
information received through that port.
enable(1) - enables the tcn-guard mode for the port.
disable(2) - disables the tcn-guard mode for the port.
The default tcn-guard mode is disabled.rw Enumeration .1.3.6.1.4.1.248.15.1.2.15.9.1.20 |
hmAgentStpCstPortLoopGuardThis command enables loop guard on this port. This setting applies
to all Spanning Tree instances of which this port is a member.
enable(1) - enables the loop guard mode for the port.
disable(2) - disables the loop guard mode for the port.
The default loop-guard mode is disabled.rw Enumeration .1.3.6.1.4.1.248.15.1.2.15.9.1.21 |
hmAgentStpMstTableMST table. SEQUENCE OF HmAgentStpMstEntry .1.3.6.1.4.1.248.15.1.2.15.10 |
hmAgentStpMstEntryMST entry. HmAgentStpMstEntry .1.3.6.1.4.1.248.15.1.2.15.10.1 |
hmAgentStpMstIdThe MSTP instance ID.ro Unsigned32 .1.3.6.1.4.1.248.15.1.2.15.10.1.1 |
hmAgentStpMstBridgePriorityThe MSTP bridge priority in a specific instance. The priority is
in the increments of 4096. The recommended default value is 32768.rw Unsigned32 .1.3.6.1.4.1.248.15.1.2.15.10.1.2 |
hmAgentStpMstBridgeIdentifierThe MSTP bridge identifier in a specific instance.ro OCTET STRING .1.3.6.1.4.1.248.15.1.2.15.10.1.3 |
hmAgentStpMstDesignatedRootIdThe MSTP designated root bridge identifier in a specific instance.ro OCTET STRING .1.3.6.1.4.1.248.15.1.2.15.10.1.4 |
hmAgentStpMstRootPathCostThe MSTP root path cost in a specific instance.ro Unsigned32 .1.3.6.1.4.1.248.15.1.2.15.10.1.5 |
hmAgentStpMstRootPortIdThe MSTP root port ID in a specific instance.ro OCTET STRING .1.3.6.1.4.1.248.15.1.2.15.10.1.6 |
hmAgentStpMstTimeSinceTopologyChangeThe MSTP time since the last topology change in a specific instance.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.248.15.1.2.15.10.1.7 |
hmAgentStpMstTopologyChangeCountThe MSTP count of topology changes in a specific instance.ro Counter32 .1.3.6.1.4.1.248.15.1.2.15.10.1.8 |
hmAgentStpMstTopologyChangeParmThe MSTP topology change parameter in a specific instance.ro Enumeration .1.3.6.1.4.1.248.15.1.2.15.10.1.9 |
hmAgentStpMstRowStatusThe MSTP instance status.
Supported values:
active(1) - valid instance.
createAndGo(4) - used to create a new instance.
destroy(6) - removes an instance.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.248.15.1.2.15.10.1.10 |
hmAgentStpMstPortTableMST port table. SEQUENCE OF HmAgentStpMstPortEntry .1.3.6.1.4.1.248.15.1.2.15.11 |
hmAgentStpMstPortEntryMST port entry. HmAgentStpMstPortEntry .1.3.6.1.4.1.248.15.1.2.15.11.1 |
hmAgentStpMstPortForwardingStateThe MSTP forwarding state of a specific port in a specific instance.ro Enumeration .1.3.6.1.4.1.248.15.1.2.15.11.1.1 |
hmAgentStpMstPortIdThe MSTP port identifier of a specific port in a specific instance.ro OCTET STRING .1.3.6.1.4.1.248.15.1.2.15.11.1.2 |
hmAgentStpMstPortPathCostThe MSTP port path cost in a specific instance. The default value will
correspond to the recommendation specified in IEEE 802.1s Table 13-2
which varies depending upon link speed.rw Unsigned32 .1.3.6.1.4.1.248.15.1.2.15.11.1.3 |
hmAgentStpMstPortPriorityThe MSTP port priority in a specific instance. The priority is
in the increments of 16. The default value is 128.rw Unsigned32 .1.3.6.1.4.1.248.15.1.2.15.11.1.4 |
hmAgentStpMstDesignatedBridgeIdThe MSTP designated bridge ID of a specific port in a specific instance.ro OCTET STRING .1.3.6.1.4.1.248.15.1.2.15.11.1.5 |
hmAgentStpMstDesignatedCostThe MSTP designated cost of a specific port in a specific instance.ro Unsigned32 .1.3.6.1.4.1.248.15.1.2.15.11.1.6 |
hmAgentStpMstDesignatedPortIdThe MSTP designated port ID of a specific port in a specific instance.ro OCTET STRING .1.3.6.1.4.1.248.15.1.2.15.11.1.7 |
hmAgentStpMstPortRoleIn an MSTP Bridge, the current Port Role for the Port (i.e., Root,
Alternate, Designated, or Backup), for the MSTI.ro Enumeration .1.3.6.1.4.1.248.15.1.2.15.11.1.8 |
hmAgentStpMstPortDisputedIn an MSTP Bridge, the current value of the disputed variable for
the MSTI for the Port.ro Enumeration .1.3.6.1.4.1.248.15.1.2.15.11.1.9 |
hmAgentStpMstPortLoopInconsistentStateThe loop inconsistent state of a specific port in a specific instance.
This value can only report as true(1) when loop guard is enabled on the port
and the port has transitioned from blocking state in this MST instance.ro Enumeration .1.3.6.1.4.1.248.15.1.2.15.11.1.10 |
hmAgentStpMstPortTransitionsIntoLoopInconsistentStateThe number of times this interface has transitioned into loop inconsistent state.ro Counter32 .1.3.6.1.4.1.248.15.1.2.15.11.1.11 |
hmAgentStpMstPortTransitionsOutOfLoopInconsistentStateThe number of times this interface has transitioned out of loop inconsistent state.ro Counter32 .1.3.6.1.4.1.248.15.1.2.15.11.1.12 |
hmAgentStpMstReceivedBridgeIdThe MSTP received bridge ID on a specific port in a specific instance.ro OCTET STRING .1.3.6.1.4.1.248.15.1.2.15.11.1.13 |
hmAgentStpMstReceivedRPCThe MSTP received root path cost of a specific port in a specific instance.ro Unsigned32 .1.3.6.1.4.1.248.15.1.2.15.11.1.14 |
hmAgentStpMstReceivedPortIdThe MSTP received port ID on a specific port in a specific instance.ro OCTET STRING .1.3.6.1.4.1.248.15.1.2.15.11.1.15 |
hmAgentStpMstVlanTableMST VLAN table. SEQUENCE OF HmAgentStpMstVlanEntry .1.3.6.1.4.1.248.15.1.2.15.12 |
hmAgentStpMstVlanEntryMST VLAN entry. HmAgentStpMstVlanEntry .1.3.6.1.4.1.248.15.1.2.15.12.1 |
hmAgentStpMstVlanRowStatusThe association status of an MSTP instance and a VLAN.
Supported values:
active(1) - valid association between an MSTP instance and a VLAN.
createAndGo(4) - used to create a new association between an MSTP instance and a VLAN.
destroy(6) - removes the association between an MSTP instance and a VLAN.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.248.15.1.2.15.12.1.1 |
hmAgentStpBpduGuardModeThe spanning tree BPDU Guard Mode.
enable(1) - enables BPDU Guard Mode on the switch.
disable(2) - disables BPDU Guard Mode on the switch.
The default status is disabled.rw Enumeration .1.3.6.1.4.1.248.15.1.2.15.13 |
hmAgentStpBpduFilterDefaultThe spanning tree BPDU Filter Mode, it enables BPDU Filter on all
edge ports.
enable(1) - enables BPDU Filter Mode on the switch.
disable(2) - disables BPDU Filter Mode on the switch.
The default status is disabled.rw Enumeration .1.3.6.1.4.1.248.15.1.2.15.14 |
hmAgentClassOfServiceGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.15.1.2.17 |
hmAgentClassOfServicePortTableA table that contains information about the 802.1p priority
mapping to traffic class priority queue for every physical port. SEQUENCE OF HmAgentClassOfServicePortEntry .1.3.6.1.4.1.248.15.1.2.17.1 |
hmAgentClassOfServicePortEntryA 802.1p priority mapped to a traffic class priority queue. HmAgentClassOfServicePortEntry .1.3.6.1.4.1.248.15.1.2.17.1.1 |
hmAgentClassOfServicePortPriorityThe Priority value determined for the received frame.
This value is equivalent to the priority indicated in
the tagged frame received, or one of the evaluated
priorities, determined according to the media-type.
For untagged frames received from Ethernet media, this
value is equal to the dot1dPortDefaultUserPriority value
for the ingress port. Integer32 .1.3.6.1.4.1.248.15.1.2.17.1.1.1 |
hmAgentClassOfServicePortClassTraffic class priority queue the received frame is mapped to.
The possible range depends on the number of supported traffic
classes for the appropriate port, as shown in
dot1dPortNumTrafficClasses.rw Integer32 .1.3.6.1.4.1.248.15.1.2.17.1.1.2 |
hmAgentSystemGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.15.1.3 |
hmAgentSaveConfigEnable hmAgentSaveConfig will initiate an configuration save to nvram.
Disable hmAgentSaveConfig after a configuration save will reset
hmAgentSaveConfigStatus back to notInitiated state.rw Enumeration .1.3.6.1.4.1.248.15.1.3.1 |
hmAgentClearConfigclear config to factory defaultsrw Enumeration .1.3.6.1.4.1.248.15.1.3.2 |
hmAgentClearLagsclear lag configurationrw Enumeration .1.3.6.1.4.1.248.15.1.3.3 |
hmAgentClearLoginSessionsclose all telnet sessionsrw Enumeration .1.3.6.1.4.1.248.15.1.3.4 |
hmAgentClearPasswordsreset passwordsrw Enumeration .1.3.6.1.4.1.248.15.1.3.5 |
hmAgentClearPortStatsclear all port statisticsrw Enumeration .1.3.6.1.4.1.248.15.1.3.6 |
hmAgentClearSwitchStatsclear all switch statisticsrw Enumeration .1.3.6.1.4.1.248.15.1.3.7 |
hmAgentClearTrapLogclear trap logrw Enumeration .1.3.6.1.4.1.248.15.1.3.8 |
hmAgentClearVlanclear vlan entriesrw Enumeration .1.3.6.1.4.1.248.15.1.3.9 |
hmAgentResetSystemreset the switchrw Enumeration .1.3.6.1.4.1.248.15.1.3.10 |
hmAgentSaveConfigStatusIndicates the current status of an save configuration request.ro Enumeration .1.3.6.1.4.1.248.15.1.3.11 |
hmAgentCableTesterGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.15.1.4 |
hmAgentCableTesterStatusStatus of the Virtual Cable Tester
active(1) - cable testing is in progress. Set to this value
to start the test.
success(2) - A successful test was performed. Cannot be set.
failure(3) - A failure was encountered during the test.
Cannot be set.
uninitialized(4) - No test has been performed yet. Cannot be set.rw Enumeration .1.3.6.1.4.1.248.15.1.4.1 |
hmAgentCableTesterIfIndexDetermines on which port to perform the cable test. Limited to
copper based ports.rw Unsigned32 .1.3.6.1.4.1.248.15.1.4.2 |
hmAgentCableTesterCableStatusIndicates the results of the Cable Test.
normal(1) - The cable is working correctly.
open(2) - The cable is disconnected or there is a faulty
connector.
short(3) - There is an electrical short in the cable.
unknown(4) - No test has been performed yet, or a test is
currently in progress.ro Enumeration .1.3.6.1.4.1.248.15.1.4.3 |
hmAgentCableTesterMinimumCableLengthThe estimated length of the cable in meters. This value
indicates the shortest length estimated. This object will
return 0 if hmAgentCableTesterStatus is not success(2) or the cable
length is unknown.ro Unsigned32 .1.3.6.1.4.1.248.15.1.4.4 |
hmAgentCableTesterMaximumCableLengthThe estimated length of the cable in meters. This value
indicates the longest length estimated. This object will
return 0 if hmAgentCableTesterStatus is not success(2) or the cable
length is unknown.ro Unsigned32 .1.3.6.1.4.1.248.15.1.4.5 |
hmAgentCableTesterCableFailureLocationThe estimated distance in meters from the end of the cable to
the failure location. This object will return 0 if
hmAgentCableTesterStatus is not success(2).ro Unsigned32 .1.3.6.1.4.1.248.15.1.4.6 |
hmPlatform4SwitchingTraps OBJECT IDENTIFIER .1.3.6.1.4.1.248.15.1.50 |
multipleUsersTrapThis trap is sent when more than one user is logged in with
administrative access. Only applies to CLI interface. NOTIFICATION-TYPE .1.3.6.1.4.1.248.15.1.50.1 |
broadcastStormStartTrapTrap is obsolete. NOTIFICATION-TYPE .1.3.6.1.4.1.248.15.1.50.2 |
broadcastStormEndTrapTrap is obsolete. NOTIFICATION-TYPE .1.3.6.1.4.1.248.15.1.50.3 |
linkFailureTrapTrap is obsolete. NOTIFICATION-TYPE .1.3.6.1.4.1.248.15.1.50.4 |
vlanRequestFailureTrapTrap is obsolete. NOTIFICATION-TYPE .1.3.6.1.4.1.248.15.1.50.5 |
vlanDeleteLastTrapTrap is sent when attempting to delete the last configured VLAN
or the Default VLAN. NOTIFICATION-TYPE .1.3.6.1.4.1.248.15.1.50.6 |
vlanDefaultCfgFailureTrapTrap is sent if there are failures in resetting VLAN
configuration to defaults. NOTIFICATION-TYPE .1.3.6.1.4.1.248.15.1.50.7 |
vlanRestoreFailureTrapTrap is obsolete. NOTIFICATION-TYPE .1.3.6.1.4.1.248.15.1.50.8 |
fanFailureTrapTrap is obsolete. NOTIFICATION-TYPE .1.3.6.1.4.1.248.15.1.50.9 |
stpInstanceNewRootTrapTrap is sent when this machine is a new STP Root when there is more
than one STP instance. NOTIFICATION-TYPE .1.3.6.1.4.1.248.15.1.50.10 |
stpInstanceTopologyChangeTrapTrap is sent when there is a STP topology change when there is more
than one STP instance. NOTIFICATION-TYPE .1.3.6.1.4.1.248.15.1.50.11 |
powerSupplyStatusChangeTrapTrap is obsolete. NOTIFICATION-TYPE .1.3.6.1.4.1.248.15.1.50.12 |
failedUserLoginTrapTrap is sent when a user fails to authenticate via the CLI or Web
interfaces. NOTIFICATION-TYPE .1.3.6.1.4.1.248.15.1.50.13 |
hmRadius OBJECT IDENTIFIER .1.3.6.1.4.1.248.15.8 |
hmAgentRadiusConfigGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.15.8.1 |
hmAgentRadiusMaxTransmitMaximum number of retransmissions of a RADIUS request packetrw Unsigned32 .1.3.6.1.4.1.248.15.8.1.1 |
hmAgentRadiusTimeoutTime out duration (in seconds) before packets are retransmittedrw Unsigned32 .1.3.6.1.4.1.248.15.8.1.2 |
hmAgentRadiusAccountingModeIdentifies if RADIUS Accounting has been enabled or notrw Enumeration .1.3.6.1.4.1.248.15.8.1.3 |
hmAgentRadiusStatsClearWhen set to enable(1), all Radius statistics will be reset.rw Enumeration .1.3.6.1.4.1.248.15.8.1.4 |
hmAgentRadiusAccountingIndexNextValidIndicates the next valid index into the hmAgentRadiusAccountingConfigTable
for creation. If no additional entries are allowed, this will be 0.ro Integer32 (0|1..2147483647) .1.3.6.1.4.1.248.15.8.1.5 |
hmAgentRadiusAccountingConfigTableTable with information about Radius Accounting Server IP
Addresses, port numbers and shared secret. Only one entry is
supported at this time. SEQUENCE OF HmAgentRadiusAccountingConfigEntry .1.3.6.1.4.1.248.15.8.1.6 |
hmAgentRadiusAccountingConfigEntryEntry consisting of configuration data for a Radius Accounting Server. HmAgentRadiusAccountingConfigEntry .1.3.6.1.4.1.248.15.8.1.6.1 |
hmAgentRadiusAccountingServerIndexUnique index of the configured RADIUS accounting server. The next valid
value of this object for creation is specified by
hmAgentRadiusAccountingIndexNextValid. Integer32 .1.3.6.1.4.1.248.15.8.1.6.1.1 |
hmAgentRadiusAccountingServerAddressIP Address of the configured RADIUS accounting server.
This object cannot be changed after creation.rw IpAddress .1.3.6.1.4.1.248.15.8.1.6.1.2 |
hmAgentRadiusAccountingPortPort number for the RADIUS accounting server.rw Unsigned32 .1.3.6.1.4.1.248.15.8.1.6.1.3 |
hmAgentRadiusAccountingSecretConfigured shared sercret for the RADIUS accounting server.rw DisplayString .1.3.6.1.4.1.248.15.8.1.6.1.4 |
hmAgentRadiusAccountingStatusCreates or destroys a RADIUS accounting server entry.
During creation, the next available index is specified by the
hmAgentRadiusAccountingIndexNextValid object. Rows creation using
a different value for hmAgentRadiusAccountingServerIndex will fail.
active(1) - This entry is active.
createAndGo(4) - Creates a new entry.
destroy(6) - Deletes an entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.248.15.8.1.6.1.5 |
hmAgentRadiusServerIndexNextValidIndicates the next valid index into the hmAgentRadiusServerConfigTable
for creation. If no additional entries are allowed, this will be 0.ro Integer32 (0|1..2147483647) .1.3.6.1.4.1.248.15.8.1.7 |
hmAgentRadiusServerConfigTableTable with information about Radius Authentication Server IP
Addresses, port numbers and shared secret SEQUENCE OF HmAgentRadiusServerConfigEntry .1.3.6.1.4.1.248.15.8.1.8 |
hmAgentRadiusServerConfigEntryEntry consisting of configuration data for a Radius
Authentication Server. HmAgentRadiusServerConfigEntry .1.3.6.1.4.1.248.15.8.1.8.1 |
hmAgentRadiusServerIndexUnique index of the configured RADIUS server Integer32 .1.3.6.1.4.1.248.15.8.1.8.1.1 |
hmAgentRadiusServerAddressIP Address of the configured RADIUS server.
This object cannot be changed after creation.rw IpAddress .1.3.6.1.4.1.248.15.8.1.8.1.2 |
hmAgentRadiusServerPortPort number for the RADIUS server.rw Unsigned32 .1.3.6.1.4.1.248.15.8.1.8.1.3 |
hmAgentRadiusServerSecretConfigured shared sercret for the RADIUS server.rw DisplayString .1.3.6.1.4.1.248.15.8.1.8.1.4 |
hmAgentRadiusServerPrimaryModeConfigure the RADIUS server to be the primary server. If there is any
other server that is configured to be primary, that server is set to be
a seconday server and this entry is set Primary.rw Enumeration .1.3.6.1.4.1.248.15.8.1.8.1.5 |
hmAgentRadiusServerCurrentModeIndicate if the RADIUS server is the current server in user for
authentication.ro Enumeration .1.3.6.1.4.1.248.15.8.1.8.1.6 |
hmAgentRadiusServerMsgAuthEnable or disable the message authenticator attribute for this
RADIUS server.rw Enumeration .1.3.6.1.4.1.248.15.8.1.8.1.7 |
hmAgentRadiusServerStatusCreates or destroys a RADIUS Authentication server entry.
During creation, the next available index is specified by the
hmAgentRadiusServerIndexNextValid object. Rows creation using
a different value for hmAgentRadiusServerIndex will fail.
active(1) - This entry is active.
createAndGo(4) - Creates a new entry.
destroy(6) - Deletes an entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.248.15.8.1.8.1.8 |
hmAgentMgmtSecurity OBJECT IDENTIFIER .1.3.6.1.4.1.248.15.11 |
hmAgentSSHConfigGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.15.11.2 |
hmAgentSSHAdminModeConfigures whether the SSH service is enabled on this switch. The
default value is disable(2).rw Enumeration .1.3.6.1.4.1.248.15.11.2.1 |
hmAgentSSHProtocolLevelConfigures which protocol versions of SSH are enabled on this
switch. The default value is both(3).rw Enumeration .1.3.6.1.4.1.248.15.11.2.2 |
hmAgentSSHSessionsCountCurrent number of active SSH sessions on this switch.ro Integer32 .1.3.6.1.4.1.248.15.11.2.3 |
hmAgentSSHMaxSessionsCountMax number of SSH sessions permitted on this switch.rw Integer32 .1.3.6.1.4.1.248.15.11.2.4 |
hmAgentSSHSessionTimeoutssh idle timeout value for this switch im minutes.rw Integer32 .1.3.6.1.4.1.248.15.11.2.5 |
hmAgentLogging OBJECT IDENTIFIER .1.3.6.1.4.1.248.15.14 |
hmAgentLogConfigGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.15.14.1 |
hmAgentLogSysLogConfigGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.15.14.1.4 |
hmAgentLogSyslogAdminStatusFor Enabling and Disabling logging to configured syslog hosts. Setting this to disable
stops logging to all syslog hosts.rw Enumeration .1.3.6.1.4.1.248.15.14.1.4.1 |
hmAgentLogSyslogHostTableSyslog host table containing syslog host entries. SEQUENCE OF HmAgentLogSyslogHostEntry .1.3.6.1.4.1.248.15.14.1.4.5 |
hmAgentLogSyslogHostEntrySyslog Host entry attributes. HmAgentLogSyslogHostEntry .1.3.6.1.4.1.248.15.14.1.4.5.1 |
hmAgentLogHostTableIndexIndex to syslog host entry in syslog host table. Unsigned32 .1.3.6.1.4.1.248.15.14.1.4.5.1.1 |
hmAgentLogHostTableIpAddressSyslog Host table IP Address.rw IpAddress .1.3.6.1.4.1.248.15.14.1.4.5.1.3 |
hmAgentLogHostTablePortSyslog Host table port number.rw Unsigned32 .1.3.6.1.4.1.248.15.14.1.4.5.1.4 |
hmAgentLogHostTableSeverityFilterConfigures the minimum severity that will be stored in the In Memory log.rw HmAgentLogSeverity (HMPRIV-MGMT-SNMP-MIB) .1.3.6.1.4.1.248.15.14.1.4.5.1.5 |
hmAgentLogHostTableRowStatusSyslog Host table row statusrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.248.15.14.1.4.5.1.7 |
hmPlatform4OutboundTelnetPrivate OBJECT IDENTIFIER .1.3.6.1.4.1.248.15.19 |
hmAgentOutboundTelnetGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.15.19.1 |
hmAgentOutboundTelnetAdminModeAdmin-mode of the Outbound Telnet.rw Enumeration .1.3.6.1.4.1.248.15.19.1.1 |
hmAgentOutboundTelnetMaxNoOfSessionsThe maximum no. of Outbound Telnet sessions allowed.rw Integer32 .1.3.6.1.4.1.248.15.19.1.2 |
hmAgentOutboundTelnetTimeoutThe login inactivity timeout value for Outbound Telnet.rw Integer32 .1.3.6.1.4.1.248.15.19.1.3 |
hmAgentDot1xAdvanced OBJECT IDENTIFIER .1.3.6.1.4.1.248.15.36 |
hmAgentDot1xEnhancementConfigGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.15.36.1 |
hmAgentDot1xRadiusVlanAssignmentEnable/Disable dot1x Vlan Assignment Support on the switch.rw Enumeration .1.3.6.1.4.1.248.15.36.1.1 |
hmAgentDot1xDynamicVlanCreationModeEnable/Disable dot1x dynamic vlan creation Support on the switch.rw Enumeration .1.3.6.1.4.1.248.15.36.1.2 |
hmAgentDot1xSafeVlanModeEnable/Disable dot1x safe vlan assignment on the switch
for multi-client authentication.rw Enumeration .1.3.6.1.4.1.248.15.36.1.3 |
hmAgentDot1xPortConfigGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.15.36.2 |
hmAgentDot1xPortConfigTableA table for dot1x enhanced Port details and associated functionality. SEQUENCE OF HmAgentDot1xPortConfigEntry .1.3.6.1.4.1.248.15.36.2.1 |
hmAgentDot1xPortConfigEntryRepresents entry for port config table. HmAgentDot1xPortConfigEntry .1.3.6.1.4.1.248.15.36.2.1.1 |
hmAgentDot1xPortControlModeDot1x port control mode of this port.The Port control mode .
The port control mode for this interface can take the following values ,
force-unauthorized - the port is in unauthorized mode,
auto-Port based mode. If a client authenticates suscessfully, then the interface is authorized .
Otherwise, the port is in unauthorized mode.
If more than one clients are attached to the port , then only one client needs to authenticate to allow other clients access.
force-authorized - The port is placed in authorized mode
macBased - If more than one client is attached to the port, then each client needs to authenticate separately.
This object depcreates dot1xAuthAuthControlledPortControl object in IEEE8021-PAE-MIBrw HmAgentDot1xPortControlMode .1.3.6.1.4.1.248.15.36.2.1.1.1 |
hmAgentDot1xGuestVlanIdSpecifies the Guest Vlan of the port. A port will
be moved to its Guest Vlan if no client sucessfully
authenticates on that port for the Guest Vlan Period.
A value of zero indicates no Guest Vlan is configured for the interface.rw Unsigned32 .1.3.6.1.4.1.248.15.36.2.1.1.2 |
hmAgentDot1xGuestVlanPeriodThe value, in seconds, of the guestVlanPeriod constant
currently in use for Guest Vlan Assignment for the
port .rw Unsigned32 .1.3.6.1.4.1.248.15.36.2.1.1.3 |
hmAgentDot1xUnauthenticatedVlanSpecifies the Unauthenticated Vlan of the port. A port will
be moved to its unauthenticated Vlan if the client authenticates unsucessfully
on that port .
A value of zero indicates no Unauthenticated Vlan is configured for the port.rw Unsigned32 .1.3.6.1.4.1.248.15.36.2.1.1.4 |
hmAgentDot1xMaxUsersSpecifies the maximum users or clients that can authenticate on this port when the port control mode is macBased.rw Unsigned32 .1.3.6.1.4.1.248.15.36.2.1.1.5 |
hmAgentDot1xPortVlanAssignedSpecifies the vlan the port is assigned to by Dot1x .
Only relevant if the port control mode of the port is auto.ro Unsigned32 .1.3.6.1.4.1.248.15.36.2.1.1.6 |
hmAgentDot1xPortVlanAssignedReasonReason the port is assigned to the vlan specified by hmAgentDot1xPortVlanAssigned .
Only relevant if the port control mode of the port is auto.ro Enumeration .1.3.6.1.4.1.248.15.36.2.1.1.7 |
hmAgentDot1xPortSessionTimeoutSpecifies the session timeout value assigned by the Radius server for this port .
Only relevant if the port control mode of the port is auto.ro Unsigned32 .1.3.6.1.4.1.248.15.36.2.1.1.8 |
hmAgentDot1xPortTerminationActionSpecifies the session termination action assigned by the Radius Server .This is the action taken when the session times out .
Only relevant if the port control mode of the port is auto.ro HmAgentDot1xSessionTerminationAction .1.3.6.1.4.1.248.15.36.2.1.1.9 |
hmAgentDot1xPortMABenabledSpecifies if Mac-based bypass authentication is configured for the port.rw Enumeration .1.3.6.1.4.1.248.15.36.2.1.1.10 |
hmAgentDot1xPortMABenabledOperationalDisplays the operational value of the Mac-based authentication bypass mode (MAB) on the port.ro Enumeration .1.3.6.1.4.1.248.15.36.2.1.1.11 |
hmAgentDot1xClientConfigGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.15.36.3 |
hmAgentDot1xClientConfigTableA table for dot1x Client details and associated functionality. SEQUENCE OF HmAgentDot1xClientConfigEntry .1.3.6.1.4.1.248.15.36.3.1 |
hmAgentDot1xClientConfigEntryRepresents entry for port config table. HmAgentDot1xClientConfigEntry .1.3.6.1.4.1.248.15.36.3.1.1 |
hmAgentDot1xClientMacAddressSpecifies the client MAC address of the client.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.248.15.36.3.1.1.1 |
hmAgentDot1xLogicalPortSpecifies the client MAC address of the client .ro Unsigned32 .1.3.6.1.4.1.248.15.36.3.1.1.2 |
hmAgentDot1xInterfaceSpecifies the physical interface to which the client is attached .ro Unsigned32 .1.3.6.1.4.1.248.15.36.3.1.1.3 |
hmAgentDot1xClientAuthPAEstateThe current value of the Authenticator PAE state
machine for the client.ro Enumeration .1.3.6.1.4.1.248.15.36.3.1.1.4 |
hmAgentDot1xClientBackendStateThe current state of the Backend Authentication
state machine.ro Enumeration .1.3.6.1.4.1.248.15.36.3.1.1.5 |
hmAgentDot1xClientUserNameSpecifies the username with which the client is authenticated to the Radius server .
This value is only valid when the client is in authenticated state.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.248.15.36.3.1.1.6 |
hmAgentDot1xClientSessionTimeSpecifies the time elapsed in seconds since the client was authenticated in this session.
This value is only valid when the client is in authenticated state.ro Unsigned32 .1.3.6.1.4.1.248.15.36.3.1.1.7 |
hmAgentDot1xClientFilterIDSpecifies the Filter ID or Diffserv Policy name to be applied to the session .
This vlaue is populated only if it has been assigned by the RADIUS server.
This value is only valid when the client is in authenticated state.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.248.15.36.3.1.1.8 |
hmAgentDot1xClientVlanAssignedSpecifies the vlan the client is associated with by Dot1x .
This value is only valid when the client is in authenticated state.ro Unsigned32 .1.3.6.1.4.1.248.15.36.3.1.1.9 |
hmAgentDot1xClientVlanAssignedReasonReason the client is associated to the vlan specified by hmAgentDot1xClientVlanAssigned .
This value is only valid when the client is in authenticated state.ro Enumeration .1.3.6.1.4.1.248.15.36.3.1.1.10 |
hmAgentDot1xClientSessionTimeoutSpecifies the session time remaining for the client if assigned by the Radius server .
A value of 0 indicates that no session timeout was assigned by the RADIUS server.
This value is only valid when the client is in authenticated state.ro Unsigned32 .1.3.6.1.4.1.248.15.36.3.1.1.11 |
hmAgentDot1xClientTerminationActionSpecifies the session termination action assigned by the Radius Server .
This is the action taken when the session times out .
This value is only valid when the client is in authenticated state.ro HmAgentDot1xSessionTerminationAction .1.3.6.1.4.1.248.15.36.3.1.1.12 |
dot1xTraps OBJECT IDENTIFIER .1.3.6.1.4.1.248.15.36.4 |
dot1xPortStatusAuthorizedDOT1X port status is authorized. NOTIFICATION-TYPE .1.3.6.1.4.1.248.15.36.4.1 |
dot1xPortStatusUnauthorizedDOT1X port status is unauthorized. NOTIFICATION-TYPE .1.3.6.1.4.1.248.15.36.4.2 |