HM2-DEVMGMT-MIB
Hirschmann Device Management MIB. Copyright (C) 2012. All Rights Reserved.
Main OID:
hm2DeviceMgmtMib.1.3.6.1.4.1.248.11.10
197
Objects
Active
Status
6
Dependencies
Imported Objects
Objects
197 total| Object Name |
|---|
hm2DeviceMgmtMibHirschmann Device Management MIB. Copyright (C) 2012. All Rights Reserved. MODULE-IDENTITY .1.3.6.1.4.1.248.11.10 |
hm2DeviceMgmtMibNotifications OBJECT IDENTIFIER .1.3.6.1.4.1.248.11.10.0 |
hm2SfpChangeTrapThis trap is sent when a SFP has been added or removed. It is also sent for an otherwise unsupported SFP. NOTIFICATION-TYPE .1.3.6.1.4.1.248.11.10.0.1 |
hm2AutoDisablePortTrapThis trap is sent if the port has been disabled or enabled by auto disable feature. NOTIFICATION-TYPE .1.3.6.1.4.1.248.11.10.0.2 |
hm2ModulePluggedTrapThis trap is sent if a module is plugged into a unit. NOTIFICATION-TYPE .1.3.6.1.4.1.248.11.10.0.3 |
hm2ModuleRemovedTrapThis trap is sent if a module is removed from a unit. NOTIFICATION-TYPE .1.3.6.1.4.1.248.11.10.0.4 |
hm2SFPRxPowerChangeTrapThis trap is sent when the state (hm2SfpCurrentRxPowerState) of the rx power of a SFP changes. NOTIFICATION-TYPE .1.3.6.1.4.1.248.11.10.0.5 |
hm2DeviceMgmtMibObjects OBJECT IDENTIFIER .1.3.6.1.4.1.248.11.10.1 |
hm2DeviceMgmtGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.11.10.1.1 |
hm2DevMgmtProductIdManufacturer-defined product identifier (product family + product ID). Example:Objekt-ID 1.3.6.1.4.1.248.11.2.1.1 is the hm2ProductFamily EES and Objekt-ID 1.3.6.1.4.1.248.11.2.1.1.2 is the Product ID for ees25-0600ro OBJECT IDENTIFIER .1.3.6.1.4.1.248.11.10.1.1.1 |
hm2DevMgmtProductDescrManufacturer-defined product description.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.248.11.10.1.1.2 |
hm2DevMgmtSerialNumberManufacturer-defined serial number of the device.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.248.11.10.1.1.3 |
hm2DeviceMgmtActionGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.11.10.1.2 |
hm2DevMgmtActionResetSetting the object to 'reset' has the same effect as a power-on sequence (cold start) Reading the object always returns 'other'.rw Enumeration .1.3.6.1.4.1.248.11.10.1.2.1 |
hm2DevMgmtActionFlushFDBSetting the object to 'flushFDB' will flush the forwarding database of the switch. Reading the object always returns 'other'.rw Enumeration .1.3.6.1.4.1.248.11.10.1.2.2 |
hm2DevMgmtActionFlushARPSetting the object to 'flushARP' will flush the ARP cache. Reading the object always returns 'other'.rw Enumeration .1.3.6.1.4.1.248.11.10.1.2.3 |
hm2DevMgmtActionFlushIGSSetting the object to 'flushIGS' will flush all dynamically learnt IGMP snooping entries. Reading the object always returns 'other'.rw Enumeration .1.3.6.1.4.1.248.11.10.1.2.4 |
hm2DevMgmtActionFlushPortStatsSetting the object to 'flushPortStats' will flush all port statistics. Reading the object always returns 'other'.rw Enumeration .1.3.6.1.4.1.248.11.10.1.2.5 |
hm2DevMgmtActionFlushEmailLogStatsSetting the object to 'flushEmailLogCounters' will flush all email logging statistics. Reading the object always returns 'other'.rw Enumeration .1.3.6.1.4.1.248.11.10.1.2.6 |
hm2DevMgmtActionFlushMMRPSetting the object to 'flushMMRP' will flush all MMRP counters. Reading the object always returns 'other'.rw Enumeration .1.3.6.1.4.1.248.11.10.1.2.7 |
hm2DevMgmtActionFlushMVRPSetting the object to 'flushMVRP' will flush all MVRP counters. Reading the object always returns 'other'.rw Enumeration .1.3.6.1.4.1.248.11.10.1.2.8 |
hm2DevMgmtActionFlushMSRPSetting the object to 'flushMSRP' will flush all MSRP counters. Reading the object always returns 'other'.rw Enumeration .1.3.6.1.4.1.248.11.10.1.2.9 |
hm2DevMgmtActionFlushIeee8021ASSetting the object to 'flushIeee8021AS' will flush all IEEE8021AS related counters. Reading the object always returns 'other'.rw Enumeration .1.3.6.1.4.1.248.11.10.1.2.10 |
hm2DevMgmtActionFlushDnsClientCacheSetting the object to 'flushDnsClientCache' will flush all DNS client cache records. Reading the object always returns 'other'.rw Enumeration .1.3.6.1.4.1.248.11.10.1.2.11 |
hm2DevMgmtActionFlushDnsCachingServerCacheSetting the object to 'flushDnsCachingServerCache' will flush all DNS caching server cache records. Reading the object always returns 'other'.rw Enumeration .1.3.6.1.4.1.248.11.10.1.2.12 |
hm2DevMgmtActionFlushIpUdpHelperStatsSetting the object to 'flushIpUdpHelperStats' will flush all ip udp helper statistics. Reading the object always returns 'other'.rw Enumeration .1.3.6.1.4.1.248.11.10.1.2.13 |
hm2DevMgmtActionFlushAclStatsSetting the object to 'flushAclStats' will flush all acl statistics from the AgentAclRuleTable. Setting the object to 'flushAclMacStats' will flush all acl statistics from the AgentAclMacRuleTable. Reading the object always returns 'other'.rw Enumeration .1.3.6.1.4.1.248.11.10.1.2.14 |
hm2DevMgmtActionFlushLdapUserCacheSetting the object to 'flushLdapUserCache' will flush all cached users from LDAP queries to an Active Directory Server. Reading the object always returns 'other'.rw Enumeration .1.3.6.1.4.1.248.11.10.1.2.15 |
hm2DevMgmtActionDelayPresetTime in seconds until a reset that was triggered over the hm2DevMgmtActionReset object is executed. Writing a zero will cancel any scheduled reset.rw Integer32 .1.3.6.1.4.1.248.11.10.1.2.100 |
hm2DevMgmtActionDelayCurrentIf a delayed reset is scheduled this object will decrement from the start value to zero.ro Integer32 .1.3.6.1.4.1.248.11.10.1.2.101 |
hm2DeviceMgmtSoftwareGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.11.10.1.3 |
hm2DeviceMgmtSoftwareVersionGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.11.10.1.3.1 |
hm2DevMgmtSwVersBootcodeSoftware version of the boot code.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.248.11.10.1.3.1.1 |
hm2DevMgmtSwVersTableThis table contains all information related to running and stored software versions on the device. The limit are 24 firmware (*.bin) files in up to 5 directory levels. SEQUENCE OF Hm2DevMgmtSwVersEntry .1.3.6.1.4.1.248.11.10.1.3.1.10 |
hm2DevMgmtSwVersEntryThe entry of the hm2DevMgmtSwVersTable. Hm2DevMgmtSwVersEntry .1.3.6.1.4.1.248.11.10.1.3.1.10.1 |
hm2DevMgmtSwFileLocationIndicates the file location (ram, flash, sd-card or usb). Enumeration .1.3.6.1.4.1.248.11.10.1.3.1.10.1.1 |
hm2DevMgmtSwFileTypeIndicates the file type (firmware, applet, logic). Enumeration .1.3.6.1.4.1.248.11.10.1.3.1.10.1.2 |
hm2DevMgmtSwFileIdxIndicates the index. For flash the index has the following meaning: - flash.xxx.1 = bootable version in flash (ROM) - flash.xxx.2 = backup version in flash (BAK) Integer32 .1.3.6.1.4.1.248.11.10.1.3.1.10.1.3 |
hm2DevMgmtSwFileNameIndicates the file name.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.248.11.10.1.3.1.10.1.4 |
hm2DevMgmtSwVersionVersion of the stored software.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.248.11.10.1.3.1.10.1.5 |
hm2DevMgmtSwMajorRelNumShows the major release number of the firmware.ro Integer32 .1.3.6.1.4.1.248.11.10.1.3.1.10.1.6 |
hm2DevMgmtSwMinorRelNumShows the minor release number of the firmware.ro Integer32 .1.3.6.1.4.1.248.11.10.1.3.1.10.1.7 |
hm2DevMgmtSwBugfixRelNumShows the bug fix release number of the firmware.ro Integer32 .1.3.6.1.4.1.248.11.10.1.3.1.10.1.8 |
hm2DeviceMgmtHardwareGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.11.10.1.4 |
hm2DevMgmtHwVersionVersion of the device hardware.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.248.11.10.1.4.1 |
hm2DevMgmtSwitchingCoreVersionVersion of the device hardware.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.248.11.10.1.4.2 |
hm2DeviceMgmtLogicVersionGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.11.10.1.4.5 |
hm2DevMgmtLogicVersTableThe table displays all versions of supported logic modules. SEQUENCE OF Hm2DevMgmtLogicVersEntry .1.3.6.1.4.1.248.11.10.1.4.5.1 |
hm2DevMgmtLogicVersEntryThe entry of the hm2DevMgmtLogicVersTable. Hm2DevMgmtLogicVersEntry .1.3.6.1.4.1.248.11.10.1.4.5.1.1 |
hm2DevMgmtLogicIdxIndex of the module to display. Integer32 .1.3.6.1.4.1.248.11.10.1.4.5.1.1.1 |
hm2DevMgmtLogicAddressAddress of the logic module in fpga.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.248.11.10.1.4.5.1.1.2 |
hm2DevMgmtLogicVersionVersion of the logic module in fpga.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.248.11.10.1.4.5.1.1.3 |
hm2DeviceMgmtTemperatureGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.11.10.1.5 |
hm2DevMgmtTemperatureThis object is used to identify the temperature within a device in units of centigrade (Celsius).ro Integer32 .1.3.6.1.4.1.248.11.10.1.5.1 |
hm2DevMgmtTemperatureUpperLimitThis object is used to define a maximum level for the temperature within a device. If the temperature rises above this upper limit, the management station will be notified by a hm2DevMgmtTemperature trap.rw Integer32 (-99..99) .1.3.6.1.4.1.248.11.10.1.5.2 |
hm2DevMgmtTemperatureLowerLimitThis object is used to define a minimum level for the temperature within a device. If the temperature falls below this lower limit, the management station will be notified by a hm2DevMgmtTemperature trap.rw Integer32 (-99..99) .1.3.6.1.4.1.248.11.10.1.5.3 |
hm2IfaceGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.11.10.1.6 |
hm2IfaceTableThis table contains extended PHY capabilities and configuration options. SEQUENCE OF Hm2IfaceEntry .1.3.6.1.4.1.248.11.10.1.6.1 |
hm2IfaceEntryEntry with the configuration options and supported features of a port. Hm2IfaceEntry .1.3.6.1.4.1.248.11.10.1.6.1.1 |
hm2IfacePhysIndexThe index of the available physical interfaces.ro Integer32 .1.3.6.1.4.1.248.11.10.1.6.1.1.1 |
hm2IfacePortCapabilityBitsmanual-mdix - port supports MDIX and MDI auto-mdix - port supports MDIX and Auto-MDIX auto-power-down - port can enter low power mode if no link is established energy-efficient-ethernet - port supports EEE cable-test - port supports cable testingro Bits .1.3.6.1.4.1.248.11.10.1.6.1.1.2 |
hm2IfaceCableCrossingThis variable configures the cable crossing on twisted pair cables. When set to 'mdi', the device does not swap the send and receive line pairs of the TP cable for this port. When set to 'mdix', the device swaps the send and receive line pairs of the TP cable for this port. When set to 'auto-mdix', the port uses the auto crossover mode. 'Unsupported' is shown, if a port does not support cable crossing or auto-negotiation is disabled. It is not possible to set 'unsupported' to any type of port.rw Enumeration .1.3.6.1.4.1.248.11.10.1.6.1.1.3 |
hm2IfacePowerStateThis variable configures the power on the interface. When set to 'enable' that means the interface-power is on (power up) When set to 'disable' that means the interface-power is off (power down) The interface power state settings have no effect if the interface admin state (ifAdminStatus) is enabledrw HmEnabledStatus (HM2-TC-MIB) .1.3.6.1.4.1.248.11.10.1.6.1.1.4 |
hm2IfaceAutoPowerDownThis variable configures the automatic power save mode on the interface. When set to 'auto-power-down', the port goes in a low power mode if no link is detected. When set to 'no-power-save', the port does not use the automatic power save mode. When set to 'energy-efficient-ethernet', the port uses energy-efficient-ethernet mode to save the power. 'Unsupported' is shown, if a port does not support automatic power save mode.rw Enumeration .1.3.6.1.4.1.248.11.10.1.6.1.1.5 |
hm2IfaceOperAdminStatusThis variable shows the operational admin state of a specific interface. The operational state could be different to the ifAdminStatus if the interface is forced to down by other means like hm2AutoDisableIntfOperState.ro Enumeration .1.3.6.1.4.1.248.11.10.1.6.1.1.6 |
hm2IfaceLayoutTableThis table does contain the layout of the interface modules or blocks. It contains all possible physical and logical items. This table can be used to determine any interface index according to 'IfEntry' that may exist and the name of this interface. SEQUENCE OF Hm2IfaceLayoutEntry .1.3.6.1.4.1.248.11.10.1.6.2 |
hm2IfaceLayoutEntryAn entry of a module or block of interfaces. Hm2IfaceLayoutEntry .1.3.6.1.4.1.248.11.10.1.6.2.1 |
hm2IfaceLayoutIndexThe index used for this table. Integer32 .1.3.6.1.4.1.248.11.10.1.6.2.1.1 |
hm2IfaceLayoutStartIfIndexIt specifies the first interface index of this block or module.ro InterfaceIndexOrZero (IF-MIB) .1.3.6.1.4.1.248.11.10.1.6.2.1.2 |
hm2IfaceLayoutEndIfIndexIt specifies the last interface index of this block or module that can exist for this particular device. The amount of interfaces between first and last may not be equal than to the maximum interface per module.ro InterfaceIndexOrZero (IF-MIB) .1.3.6.1.4.1.248.11.10.1.6.2.1.3 |
hm2IfaceLayoutModuleCapacityIt is the Number of modules in that block. Currently not used and it is always 0.ro Unsigned32 .1.3.6.1.4.1.248.11.10.1.6.2.1.4 |
hm2IfaceLayoutModulePortCapacityNumber of interfaces that one module can contain. Currently not used and it is always 0ro Unsigned32 .1.3.6.1.4.1.248.11.10.1.6.2.1.5 |
hm2IfaceLayoutFormatThis specifies a format string that can be used to determine the textual representation of an interface in this block. following wildcards are supported: %i the absolute interface number according to 'IfEntry'. %p the relative number based on hm2IfaceLayoutStartIfIndex %s the block number from 'hm2IfaceLayoutIndex' %vid the vlan of the routing interface %lre the name of the redundancy port (prp or hsr)ro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.248.11.10.1.6.2.1.6 |
hm2IfaceLayoutIfIndexTypeType of the interfaces in that block according to IANA-Type table.ro IANAifType (IANAifType-MIB) .1.3.6.1.4.1.248.11.10.1.6.2.1.7 |
hm2IfaceExtTableThis table contains additional information about the interfaces. SEQUENCE OF Hm2IfaceExtEntry .1.3.6.1.4.1.248.11.10.1.6.3 |
hm2IfaceExtEntry. Hm2IfaceExtEntry .1.3.6.1.4.1.248.11.10.1.6.3.1 |
hm2IfaceExtIfRoleThe current role of the interface.ro Enumeration .1.3.6.1.4.1.248.11.10.1.6.3.1.1 |
hm2SfpGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.11.10.1.7 |
hm2SfpInfoTableThis table contains variables for each SFP. SEQUENCE OF Hm2SfpInfoEntry .1.3.6.1.4.1.248.11.10.1.7.1 |
hm2SfpInfoEntryEntry for a detected SFP. Hm2SfpInfoEntry .1.3.6.1.4.1.248.11.10.1.7.1.1 |
hm2SfpModuleTypeType of the module. SFP or SFP+ (3), XFP (6).ro Enumeration .1.3.6.1.4.1.248.11.10.1.7.1.1.1 |
hm2SfpMediaTypeThe SFP's Media Typero Enumeration .1.3.6.1.4.1.248.11.10.1.7.1.1.2 |
hm2SfpConnectorThe SFP's Connector Type.ro Enumeration .1.3.6.1.4.1.248.11.10.1.7.1.1.3 |
hm2SfpVendorNameThe SFP's vendor name (ASCII).ro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.248.11.10.1.7.1.1.4 |
hm2SfpVendorOUIThe vendor organizationally unique identifier field (OUI).ro OCTET STRING .1.3.6.1.4.1.248.11.10.1.7.1.1.5 |
hm2SfpPartNumberThe part number of the module (ASCII).ro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.248.11.10.1.7.1.1.6 |
hm2SfpPartRevThe revision number of the module (ASCII).ro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.248.11.10.1.7.1.1.7 |
hm2SfpSerialNumThe SFP's serial number provided by vendor (ASCII).ro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.248.11.10.1.7.1.1.8 |
hm2SfpDateCodeThe SFP's vendor manufacturing date code. Format is YY:MM:DD.ro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.248.11.10.1.7.1.1.9 |
hm2SfpInfoVersionVersion of SFP's Hirschmann information. Contains -1 in case of a device read error.ro Integer32 .1.3.6.1.4.1.248.11.10.1.7.1.1.10 |
hm2SfpInfoPartNumberPart Number of SFP's Hirschmann information.ro SnmpAdminString .1.3.6.1.4.1.248.11.10.1.7.1.1.11 |
hm2SfpInfoPartIdPart Identifier of SFP's Hirschmann information.ro SnmpAdminString .1.3.6.1.4.1.248.11.10.1.7.1.1.12 |
hm2SfpBitRateNominalThe SFP's nominal bitrate in units of MBits/sec. Contains -1 in case of a device read error.ro Integer32 .1.3.6.1.4.1.248.11.10.1.7.1.1.13 |
hm2SfpBitRateMinThe minimum bit rate is specified in units of 100 Megabits per second, rounded off to the nearest 100 Megabits per second. A value of 0 indicates that the minimum bit rate is not specified.ro Integer32 .1.3.6.1.4.1.248.11.10.1.7.1.1.14 |
hm2SfpBitRateMaxThe maximum bit rate is specified in units of 100 Megabits per second, rounded off to the nearest 100 Megabits per second. A value of 0 indicates that the maximum bit rate is not specified.ro Integer32 .1.3.6.1.4.1.248.11.10.1.7.1.1.15 |
hm2SfpMaxLength_fiber_9Max. usable length for the cable type '9/125 micrometer fiber' with this SFP in units of meters.ro Integer32 .1.3.6.1.4.1.248.11.10.1.7.1.1.16 |
hm2SfpMaxLength_fiber_50Max. usable length for the cable type '50/125 micrometer fiber' with this SFP in units of meters.ro Integer32 .1.3.6.1.4.1.248.11.10.1.7.1.1.17 |
hm2SfpMaxLength_fiber_e50Max. usable length for the cable type 'EBW 50/125 micrometer fiber' with this SFP in units of meters or -1 if not supported.ro Integer32 .1.3.6.1.4.1.248.11.10.1.7.1.1.18 |
hm2SfpMaxLength_fiber_62_5Max. usable length for the cable type '62.5/125 micrometer fiber' with this SFP in units of meters.ro Integer32 .1.3.6.1.4.1.248.11.10.1.7.1.1.19 |
hm2SfpMaxLength_copperMax. usable length for the cable type 'copper' with this SFP in units of meters.ro Integer32 .1.3.6.1.4.1.248.11.10.1.7.1.1.20 |
hm2SfpWaveLengthNominal transmitter output wavelength at room temperature. The laser wavelength in nm (units of 0.05nm).ro Integer32 .1.3.6.1.4.1.248.11.10.1.7.1.1.21 |
hm2SfpWaveLengthToleranceThe +/- range of transmitter output wavelength under normal operating conditions or -1 if not supported.ro Integer32 .1.3.6.1.4.1.248.11.10.1.7.1.1.22 |
hm2SfpEnhancedOptionsNot supported.ro Bits .1.3.6.1.4.1.248.11.10.1.7.1.1.23 |
hm2SfpSupportedThe SFP is supported by the device (true) or not (false).ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.248.11.10.1.7.1.1.24 |
hm2SfpSupportedReasonThe reason why this SFP is supported.ro Enumeration .1.3.6.1.4.1.248.11.10.1.7.1.1.25 |
hm2SfpDiagTableThis table contains variables for each SFP. SEQUENCE OF Hm2SfpDiagEntry .1.3.6.1.4.1.248.11.10.1.7.2 |
hm2SfpDiagEntryEntry for a detected SFP. Hm2SfpDiagEntry .1.3.6.1.4.1.248.11.10.1.7.2.1 |
hm2SfpCurrentBitRateThe current bit rate in units of Megabits per second.ro Integer32 .1.3.6.1.4.1.248.11.10.1.7.2.1.1 |
hm2SfpCurrentTemperatureThis signed integer is used to identify the temperature within the SFP in units of centigrade (Celsius). Contains -1000 in case of a device read error.ro Integer32 .1.3.6.1.4.1.248.11.10.1.7.2.1.2 |
hm2SfpCurrentTxPowerThe SFP's internally measured Tx Power in units of 1/10 microwatt or -1 if it is not supported.ro Integer32 .1.3.6.1.4.1.248.11.10.1.7.2.1.3 |
hm2SfpCurrentRxPowerThe SFP's internally measured Rx Power in units of 1/10 microWatts or -10000 if not supportted.ro Integer32 .1.3.6.1.4.1.248.11.10.1.7.2.1.4 |
hm2SfpCurrentTxPowerdBmThe SFP's internally measured Tx Power in units of dBm. (ASCII representation of a floating point number). - if not supported.ro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.248.11.10.1.7.2.1.5 |
hm2SfpCurrentRxPowerdBmThe SFP's internally measured Rx Power in units of dBm. (ASCII representation of a floating point number). - if not supported.ro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.248.11.10.1.7.2.1.6 |
hm2SfpCurrentRxPowerStateThe state of the SFP's internally measured Rx.ro Enumeration .1.3.6.1.4.1.248.11.10.1.7.2.1.7 |
hm2SfpWLGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.11.10.1.7.3 |
hm2SfpWLStatusStatus of the SFP White List. present(1): a white list is present on the device absent(2): no white list is present on the device not-supported(3): white list feature is not supported in this devicero Enumeration .1.3.6.1.4.1.248.11.10.1.7.3.1 |
hm2SfpThresholdTableThis table contains the thresholds for each SFP. SEQUENCE OF Hm2SfpThresholdEntry .1.3.6.1.4.1.248.11.10.1.7.4 |
hm2SfpThresholdEntryEntry for a detected SFP. Hm2SfpThresholdEntry .1.3.6.1.4.1.248.11.10.1.7.4.1 |
hm2SfpTemperatureHighAlarmThe SFP's Temperature High Alarm threshold in units of centigrade (Celsius). It is -1000 if the SFP device does not support it or in case of a device read error.ro Integer32 .1.3.6.1.4.1.248.11.10.1.7.4.1.1 |
hm2SfpTemperatureHighWarningThe SFP's Temperature High Warning threshold in units of centigrade (Celsius). It is -1000 if the SFP device does not support it or in case of a device read error.ro Integer32 .1.3.6.1.4.1.248.11.10.1.7.4.1.2 |
hm2SfpTemperatureLowAlarmThe SFP's Temperature Low Alarm threshold in units of centigrade (Celsius). It is -1000 if the SFP device does not support it or in case of a device read error.ro Integer32 .1.3.6.1.4.1.248.11.10.1.7.4.1.3 |
hm2SfpTemperatureLowWarningThe SFP's Temperature Low Warning threshold in units of centigrade (Celsius). It is -1000 if the SFP device does not support it or in case of a device read error.ro Integer32 .1.3.6.1.4.1.248.11.10.1.7.4.1.4 |
hm2SfpTxPowerHighAlarmThe SFP's Tx Power High Alarm threshold in units of 0.1uW. It is -10000 if the SFP device does not support it or in case of a device read error.ro Integer32 .1.3.6.1.4.1.248.11.10.1.7.4.1.5 |
hm2SfpTxPowerHighWarningThe SFP's Tx Power High Warning threshold in units of 0.1uW. It is -10000 if the SFP device does not support it or in case of a device read error.ro Integer32 .1.3.6.1.4.1.248.11.10.1.7.4.1.6 |
hm2SfpTxPowerLowAlarmThe SFP's Tx Power Low Alarm threshold in units of 0.1uW. It is -10000 if the SFP device does not support it or in case of a device read error.ro Integer32 .1.3.6.1.4.1.248.11.10.1.7.4.1.7 |
hm2SfpTxPowerLowWarningThe SFP's Tx Power Low Warning threshold in units of 0.1uW. It is -10000 if the SFP device does not support it or in case of a device read error.ro Integer32 .1.3.6.1.4.1.248.11.10.1.7.4.1.8 |
hm2SfpRxPowerHighAlarmThe SFP's Rx Power High Alarm threshold in units of 0.1uW. It is -10000 if the SFP device does not support it or in case of a device read error.ro Integer32 .1.3.6.1.4.1.248.11.10.1.7.4.1.9 |
hm2SfpRxPowerHighWarningThe SFP's Rx Power High Warning threshold in units of 0.1uW. It is -10000 if the SFP device does not support it or in case of a device read error.ro Integer32 .1.3.6.1.4.1.248.11.10.1.7.4.1.10 |
hm2SfpRxPowerLowAlarmThe SFP's Rx Power Low Alarm threshold in units of 0.1uW. It is -10000 if the SFP device does not support it or in case of a device read error.ro Integer32 .1.3.6.1.4.1.248.11.10.1.7.4.1.11 |
hm2SfpRxPowerLowWarningThe SFP's Rx Power Low Warning threshold in units of 0.1uW. It is -10000 if the SFP device does not support it or in case of a device read error.ro Integer32 .1.3.6.1.4.1.248.11.10.1.7.4.1.12 |
hm2SfpTxPowerdBmHighAlarmThe SFP's Tx Power High Alarm threshold in units of dBm (ASCII representation of floating point number). It is N/A if the SFP device does not support it or in case of a device read error.ro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.248.11.10.1.7.4.1.13 |
hm2SfpTxPowerdBmHighWarningThe SFP's Tx Power High Warning threshold in units of dBm (ASCII representation of floating point number). It is N/A if the SFP device does not support it or in case of a device read error.ro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.248.11.10.1.7.4.1.14 |
hm2SfpTxPowerdBmLowAlarmThe SFP's Tx Power Low Alarm threshold in units of dBm (ASCII representation of floating point number). It is N/A if the SFP device does not support it or in case of a device read error.ro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.248.11.10.1.7.4.1.15 |
hm2SfpTxPowerdBmLowWarningThe SFP's Tx Power Low Warning threshold in units of dBm (ASCII representation of floating point number). It is N/A if the SFP device does not support it or in case of a device read error.ro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.248.11.10.1.7.4.1.16 |
hm2SfpRxPowerdBmHighAlarmThe SFP's Rx Power High Alarm threshold in units of dBm (ASCII representation of floating point number). It is N/A if the SFP device does not support it or in case of a device read error.ro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.248.11.10.1.7.4.1.17 |
hm2SfpRxPowerdBmHighWarningThe SFP's Rx Power High Warning threshold in units of dBm (ASCII representation of floating point number). It is N/A if the SFP device does not support it or in case of a device read error.ro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.248.11.10.1.7.4.1.18 |
hm2SfpRxPowerdBmLowAlarmThe SFP's Rx Power Low Alarm threshold in units of dBm (ASCII representation of floating point number). It is N/A if the SFP device does not support it or in case of a device read error.ro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.248.11.10.1.7.4.1.19 |
hm2SfpRxPowerdBmLowWarningThe SFP's Rx Power Low Warning threshold in units of dBm (ASCII representation of floating point number). It is N/A if the SFP device does not support it or in case of a device read error.ro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.248.11.10.1.7.4.1.20 |
hm2ExtNvmGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.11.10.1.8 |
hm2ExtNvmGeneralGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.11.10.1.8.1 |
hm2ExtNvmChooseActiveThe user can choose which external NV memory to use for file operations.rw Hm2DeviceExtNVMType .1.3.6.1.4.1.248.11.10.1.8.1.1 |
hm2ExtNvmLogDeviceThe user can choose which external NV memory to use for persistent logging.rw Hm2DeviceExtNVMType .1.3.6.1.4.1.248.11.10.1.8.1.2 |
hm2ExtNvmAdminModeSwitches the USB bus between High Speed (normal) and Full Speed (compatibility). This setting only takes effect after a reboot.rw Enumeration .1.3.6.1.4.1.248.11.10.1.8.1.3 |
hm2ExtNvmOperModeShows the USB mode the device is currently operating in.ro Enumeration .1.3.6.1.4.1.248.11.10.1.8.1.4 |
hm2ExtNvmTableThis table contains variables for each nvram. SEQUENCE OF Hm2ExtNvmEntry .1.3.6.1.4.1.248.11.10.1.8.2 |
hm2ExtNvmEntryEntry for an external nvram. Hm2ExtNvmEntry .1.3.6.1.4.1.248.11.10.1.8.2.1 |
hm2ExtNvmTableIndexIndex Hm2DeviceExtNVMType .1.3.6.1.4.1.248.11.10.1.8.2.1.1 |
hm2ExtNvmStatusStatus of the external non-volatile memory. notPresent(1): external non-volatile memory has not been detected. removed(2): external non-volatile memory was removed in running mode of the agent. ok(3): external non-volatile memory is present and OK. outOfMemory(4): external non-volatile memory is full. genericErr(5): Any other failure, e.g. hardware malfunction.ro Enumeration .1.3.6.1.4.1.248.11.10.1.8.2.1.2 |
hm2ExtNvmManufacturerIdThe manufacturer ID.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.248.11.10.1.8.2.1.3 |
hm2ExtNvmHWRevisionThe application ID.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.248.11.10.1.8.2.1.4 |
hm2ExtNvmProductNameThe product name.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.248.11.10.1.8.2.1.5 |
hm2ExtNvmVersionThe version.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.248.11.10.1.8.2.1.6 |
hm2ExtNvmSerialNumThe serial number provided by vendor (ASCII).ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.248.11.10.1.8.2.1.7 |
hm2ExtNvmAutomaticSoftwareLoadEnable or disable Automatic loading of a software image from the external non-volatile memory. A file named 'startup.txt' must be present on the external non-volatile memory and contain the line 'autoUpdate=filename'.rw HmEnabledStatus (HM2-TC-MIB) .1.3.6.1.4.1.248.11.10.1.8.2.1.8 |
hm2ExtNvmConfigLoadPrioritySet the priority of this external non-volatile memory for loading the configuration while booting. The configuration on the device with the lowest priority is loaded. Setting this variable to 0 disables loading of a configuration from this device.rw Enumeration .1.3.6.1.4.1.248.11.10.1.8.2.1.9 |
hm2ExtNvmConfigSaveEnable or disable Automatic saving of the configuration to the external non-volatile memory. If this is enabled, saving the configuration of the device to its internal nvram also stores in on this external nvram.rw HmEnabledStatus (HM2-TC-MIB) .1.3.6.1.4.1.248.11.10.1.8.2.1.10 |
hm2ExtNvmWritableShows if writing to the device is possible, i.e. if it is write protected.ro HmEnabledStatus (HM2-TC-MIB) .1.3.6.1.4.1.248.11.10.1.8.2.1.11 |
hm2ExtNvmAutomaticSshKeyLoadEnable or disable automatic loading of a SSH key from the external non-volatile memory. A file named 'startup.txt' must be present on the external non-volatile memory and contain the line 'autoUpdateRSA=' and/or 'autoUpdateDSA='.rw HmEnabledStatus (HM2-TC-MIB) .1.3.6.1.4.1.248.11.10.1.8.2.1.12 |
hm2AutoDisableGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.11.10.1.9 |
hm2AutoDisableIntfTablePort Auto Disable interface table. SEQUENCE OF Hm2AutoDisableIntfEntry .1.3.6.1.4.1.248.11.10.1.9.1 |
hm2AutoDisableIntfEntryPort Auto Disable interface entry. Hm2AutoDisableIntfEntry .1.3.6.1.4.1.248.11.10.1.9.1.1 |
hm2AutoDisableIntfRemainingTimeRemaining time in seconds until the re-activation of the port.ro Unsigned32 .1.3.6.1.4.1.248.11.10.1.9.1.1.1 |
hm2AutoDisableIntfComponentNameName of the component that triggered the errorro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.248.11.10.1.9.1.1.2 |
hm2AutoDisableIntfErrorReasonError disable reasonro Enumeration .1.3.6.1.4.1.248.11.10.1.9.1.1.3 |
hm2AutoDisableIntfTimerTimer value in seconds after a deactivated port is activated again. Possible values are: 30-4294967295. A value of 0 disables the timer.rw Unsigned32 (0|30..4294967295) .1.3.6.1.4.1.248.11.10.1.9.1.1.4 |
hm2AutoDisableIntfResetPort Auto Disable interface reset.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.248.11.10.1.9.1.1.5 |
hm2AutoDisableIntfOperStateStatus of Auto Disable interface admin state. Active means that a component has encountered an error and Auto-Disable has turned off the interface. Inactive means that currently there is no errorro Enumeration .1.3.6.1.4.1.248.11.10.1.9.1.1.6 |
hm2AutoDisableIntfErrorTimeLocal system time (hm2SystemLocalTime) when the error occured.ro HmTimeSeconds1970 (HM2-TC-MIB) .1.3.6.1.4.1.248.11.10.1.9.1.1.7 |
hm2AutoDisableReasonTablePossible reasons for Auto Disable SEQUENCE OF Hm2AutoDisableReasonEntry .1.3.6.1.4.1.248.11.10.1.9.2 |
hm2AutoDisableReasonEntryPort Auto Disable interface entry. Hm2AutoDisableReasonEntry .1.3.6.1.4.1.248.11.10.1.9.2.1 |
hm2AutoDisableReasonsReason for deactivation a port Enumeration .1.3.6.1.4.1.248.11.10.1.9.2.1.1 |
hm2AutoDisableReasonOperationEnables/disables recovery by resaon on this device.rw HmEnabledStatus (HM2-TC-MIB) .1.3.6.1.4.1.248.11.10.1.9.2.1.2 |
hm2AutoDisableReasonCategoryAuto Disable Reason Categoryro Enumeration .1.3.6.1.4.1.248.11.10.1.9.2.1.3 |
hm2UnitGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.11.10.1.10 |
hm2UnitTableThis table contains unit capabilities and configuration options. SEQUENCE OF Hm2UnitEntry .1.3.6.1.4.1.248.11.10.1.10.100 |
hm2UnitEntryEntry with the configuration options and supported features of a unit. Hm2UnitEntry .1.3.6.1.4.1.248.11.10.1.10.100.1 |
hm2UnitIndexThe index of the available unit.ro Integer32 .1.3.6.1.4.1.248.11.10.1.10.100.1.1 |
hm2UnitMaxModuleCapacityMaximum number of modules that this unit can contain in this system.ro Integer32 .1.3.6.1.4.1.248.11.10.1.10.100.1.2 |
hm2UnitMaxModulePortCapacityMaximum number of ports that a module can contain in this unit.ro Integer32 .1.3.6.1.4.1.248.11.10.1.10.100.1.3 |
hm2ModuleGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.11.10.1.11 |
hm2ModuleTableThis table contains capabilities and configuration options of device modules. SEQUENCE OF Hm2ModuleEntry .1.3.6.1.4.1.248.11.10.1.11.100 |
hm2ModuleEntryEntry with the configuration options and supported features of a device module. Hm2ModuleEntry .1.3.6.1.4.1.248.11.10.1.11.100.1 |
hm2ModuleIndexThe index of the available module.ro Integer32 .1.3.6.1.4.1.248.11.10.1.11.100.1.1 |
hm2ModuleIdManufacturer-defined product identifier (module family + product ID). Example: Object-ID 1.3.6.1.4.1.248.11.2.2.1 is the hm2ModuleFamily MSM and Object-ID 1.3.6.1.4.1.248.11.2.2.1.1 is the Product ID for msm-4txro OBJECT IDENTIFIER .1.3.6.1.4.1.248.11.10.1.11.100.1.2 |
hm2ModuleDescriptionDescription of the module. This value cannot be written by external entities (only for internal purposes).rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.248.11.10.1.11.100.1.3 |
hm2ModuleProductCodeProduct Code of the module.ro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.248.11.10.1.11.100.1.4 |
hm2ModuleVersionVersion of the module.ro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.248.11.10.1.11.100.1.5 |
hm2ModuleNumOfPortsThe numberOfPorts is the number of ports contained within the module. Within each module, the ports are uniquely numbered in the range from 1 to numberOfPorts.ro Integer32 .1.3.6.1.4.1.248.11.10.1.11.100.1.6 |
hm2ModuleFirstMauIndexValue of the first mauIndex used by the module. **NOTE: This object is obsolete in favour of hm2ModuleFirstIfIndex.**roobsolete Integer32 .1.3.6.1.4.1.248.11.10.1.11.100.1.7 |
hm2ModuleStatusStatus of the module. If the value is physical(1), then the module is plugged in, if the value is configurable, the ports can be configured, but the card is absent, with the value remove(3) written to the agent the card can be logically removed. The value fix(4) is for modules which cannot be removed.rw Enumeration .1.3.6.1.4.1.248.11.10.1.11.100.1.8 |
hm2ModuleSerialNumThe serial number provided by vendor (ASCII).ro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.248.11.10.1.11.100.1.9 |
hm2ModuleMinSWVersionThe minimum software version required to support this module.ro Integer32 .1.3.6.1.4.1.248.11.10.1.11.100.1.10 |
hm2ModuleCapabilitypoe - module supports Power over Ethernet, fpga - module has a FPGA, ptp - module supports PTP, io-module - module is an IO module. This value cannot be written by external entities (only for internal purposes).rw Bits .1.3.6.1.4.1.248.11.10.1.11.100.1.11 |
hm2ModuleInternalIDAn internal ID of the Module. This value cannot be written by external entities (only for internal purposes).rw Integer32 .1.3.6.1.4.1.248.11.10.1.11.100.1.12 |
hm2ModuleInternalIDVariantAn internal variant ID of the Module. **NOTE: This object is obsolete.**rwobsolete Integer32 .1.3.6.1.4.1.248.11.10.1.11.100.1.13 |
hm2ModuleFirstIfIndexValue of the first ifIndex used by the module.ro Integer32 .1.3.6.1.4.1.248.11.10.1.11.100.1.14 |
hm2ModuleAdminStateEnable or disable the module. If disabled, module plugged in this slot will not be activated.rw HmEnabledStatus (HM2-TC-MIB) .1.3.6.1.4.1.248.11.10.1.11.100.1.15 |