Home/Catalog/HM2-DIAGNOSTIC-MIB

HM2-DIAGNOSTIC-MIB

AI MIB Summary

The HM2-DIAGNOSTIC-MIB facilitates the monitoring of internal hardware health and fault conditions on Hirschmann (Belden) network switches, specifically exposing diagnostic data such as temperature sensors, voltage levels, fan status, and power supply integrity via SNMP.

Hirschmann Diagnostic MIB. Copyright (C) 2012. All Rights Reserved.
Main OID:
hm2DiagnosticMib.1.3.6.1.4.1.248.11.22
218
Objects
Active
Status
6
Dependencies

Imported Objects

SNMPv2-SMI
SNMPv2-TC
IF-MIB
HM2-TC-MIB
HM2-PWRMGMT-MIB
HM2-DEVMGMT-MIB

Objects

218 total
Object Name
hm2DiagnosticMibHirschmann Diagnostic MIB. Copyright (C) 2012. All Rights Reserved.
MODULE-IDENTITY
.1.3.6.1.4.1.248.11.22
hm2DiagnosticMibNotifications
OBJECT IDENTIFIER
.1.3.6.1.4.1.248.11.22.0
hm2SigConStateChangeTrapThis trap is sent if the value of hm2SigConState changes its value.
NOTIFICATION-TYPE
.1.3.6.1.4.1.248.11.22.0.1
hm2DevMonStateChangeTrapThis trap is sent if the value of hm2DevMonState changes its value.
NOTIFICATION-TYPE
.1.3.6.1.4.1.248.11.22.0.2
hm2DevSecStateChangeTrapThis trap is sent if the value of hm2DevSecState changes its value.
NOTIFICATION-TYPE
.1.3.6.1.4.1.248.11.22.0.3
hm2DiagSelftestActionTrapThis trap is sent if a self-test action is performed and hm2DiagSelftestAction is configured to sendTrap(2).
NOTIFICATION-TYPE
.1.3.6.1.4.1.248.11.22.0.4
hm2DiagIfaceUtilizationTrapThis trap is sent if the value of hmIfaceUtilization exceeds or falls back below the interface utilization thresholds hmIfaceUtilizationAlarmConditionThreshold and hmIfaceUtilizationAlarmRemovalThreshold.
NOTIFICATION-TYPE
.1.3.6.1.4.1.248.11.22.0.5
hm2PortMonitorPortTrapThis trap is sent if the a port has been disabled by port disable action by port monitor.
NOTIFICATION-TYPE
.1.3.6.1.4.1.248.11.22.0.6
hm2DiagnosticMibObjects
OBJECT IDENTIFIER
.1.3.6.1.4.1.248.11.22.1
hm2DiagSelftestGroup
OBJECT IDENTIFIER
.1.3.6.1.4.1.248.11.22.1.1
hm2DiagSelftestRAMControls RAM self-test on cold start of the device. When disabled the device booting time is reduced.rw
HmEnabledStatus (HM2-TC-MIB)
.1.3.6.1.4.1.248.11.22.1.1.1
hm2DiagSelftestBootTimeInternal boot time in Milliseconds until activating ports.ro
Integer32
.1.3.6.1.4.1.248.11.22.1.1.2
hm2DiagSelftestActionTableDiag self test action group.
SEQUENCE OF Hm2DiagSelftestActionEntry
.1.3.6.1.4.1.248.11.22.1.1.10
hm2DiagSelftestActionEntryDiag self test action entry.
Hm2DiagSelftestActionEntry
.1.3.6.1.4.1.248.11.22.1.1.10.1
hm2DiagSelftestActionCauseThe area of the cause for the action the self-test wants to take.ro
Enumeration
.1.3.6.1.4.1.248.11.22.1.1.10.1.1
hm2DiagSelftestActionThe action that the self-test component should take. The cause is always logged to the system log, additionally a trap can be sent to the management station or a reboot can be performed.rw
Enumeration
.1.3.6.1.4.1.248.11.22.1.1.10.1.2
hm2DiagBootGroup
OBJECT IDENTIFIER
.1.3.6.1.4.1.248.11.22.1.2
hm2BootSystemMonitorEnable or disable the System Monitor access during the boot phase. Please note: If the System Monitor is disabled, it is possible to lose access to the device permanently in case of loosing administrator password or misconfiguration.rw
HmEnabledStatus (HM2-TC-MIB)
.1.3.6.1.4.1.248.11.22.1.2.1
hm2BootDefaultConfigOnErrorEnable or disable loading of the default configuration in case there is any error loading the configuration during the boot phase. If disabled the system will be halted.rw
HmEnabledStatus (HM2-TC-MIB)
.1.3.6.1.4.1.248.11.22.1.2.2
hm2BootConfigPushButtonEnable or disable the push button functionality on the device.rw
HmEnabledStatus (HM2-TC-MIB)
.1.3.6.1.4.1.248.11.22.1.2.3
hm2DiagDeviceMonitorGroup
OBJECT IDENTIFIER
.1.3.6.1.4.1.248.11.22.1.3
hm2SignalContactGroup
OBJECT IDENTIFIER
.1.3.6.1.4.1.248.11.22.1.3.1
hm2SigConCommonTableThis table contains all variables to configure the behavior of the signalling contacts.
SEQUENCE OF Hm2SigConCommonEntry
.1.3.6.1.4.1.248.11.22.1.3.1.1
hm2SigConCommonEntryThe entry of the hm2SigConConfigTable.
Hm2SigConCommonEntry
.1.3.6.1.4.1.248.11.22.1.3.1.1.1
hm2SigConIDThis index is used to identify the associated signalling contact.ro
Integer32
.1.3.6.1.4.1.248.11.22.1.3.1.1.1.1
hm2SigConTrapEnableDetermines whether a trap shall be sent or not, when the signal contact operating state changes.rw
HmEnabledStatus (HM2-TC-MIB)
.1.3.6.1.4.1.248.11.22.1.3.1.1.1.2
hm2SigConTrapCauseThis object identifies the cause for a trap. The index of the entity which produces the trap is specified by hm2SigConTrapCauseIndex.ro
Enumeration
.1.3.6.1.4.1.248.11.22.1.3.1.1.1.3
hm2SigConTrapCauseIndexThis attribute specifies the entity which produces the trap. power-supply: index of power-supply table link-failure: index of interface table temperature: 0 ext-nvm-removal: (1) sd, (2) usb, (3) serial (not supported yet) ext-nvm-not-in-sync: (1) sd, (2) usb, (3) serial (not supported yet) ring-redundancy: (1) MRP, (2) PRP, (3) HSR, (4) DLR ext-nvm-update-enabled: (1) sd, (2) usb, (3) serial (not supported yet) no-link: index of interface table 0: other errorsro
Integer32
.1.3.6.1.4.1.248.11.22.1.3.1.1.1.4
hm2SigConModeThis attribute specifies the behavior of the relay contact. The factory settings for signal contact 1 is monitoring the correct operation of entries specified to be survived. When the device has also a second signal contact, the factory setting for it is the manual mode.rw
Enumeration
.1.3.6.1.4.1.248.11.22.1.3.1.1.1.5
hm2SigConOperStateThis attribute shows the current operating state of the signal contact.ro
Enumeration
.1.3.6.1.4.1.248.11.22.1.3.1.1.1.6
hm2SigConOperTimeStampThis attribute shows local system time (hm2SystemLocalTime) of the last hm2SigConOperState change.ro
HmTimeSeconds1970 (HM2-TC-MIB)
.1.3.6.1.4.1.248.11.22.1.3.1.1.1.7
hm2SigConManualActivateWhen operating in manual mode, the signal contact state can be set by this attribute.rw
Enumeration
.1.3.6.1.4.1.248.11.22.1.3.1.1.1.8
hm2SigConSenseLinkFailureSets the monitoring of the network connection(s).rw
HmEnabledStatus (HM2-TC-MIB)
.1.3.6.1.4.1.248.11.22.1.3.1.1.1.9
hm2SigConSenseTemperatureSets the monitoring of the device temperature.rw
HmEnabledStatus (HM2-TC-MIB)
.1.3.6.1.4.1.248.11.22.1.3.1.1.1.10
hm2SigConSenseFanSets the monitoring of the device fan. (currently not supported)rw
HmEnabledStatus (HM2-TC-MIB)
.1.3.6.1.4.1.248.11.22.1.3.1.1.1.11
hm2SigConSenseModuleRemovalSets the monitoring of module removal (platform dependant).rw
HmEnabledStatus (HM2-TC-MIB)
.1.3.6.1.4.1.248.11.22.1.3.1.1.1.12
hm2SigConSenseExtNvmRemovalSets the monitoring of the external non-volatile memory removal.rw
HmEnabledStatus (HM2-TC-MIB)
.1.3.6.1.4.1.248.11.22.1.3.1.1.1.13
hm2SigConSenseExtNvmNotInSyncSets the monitoring whether the external non-volatile memory is in sync with the configuration in NVRAM.rw
HmEnabledStatus (HM2-TC-MIB)
.1.3.6.1.4.1.248.11.22.1.3.1.1.1.14
hm2SigConSenseRingRedundancySets the monitoring of the ring redundancy.rw
HmEnabledStatus (HM2-TC-MIB)
.1.3.6.1.4.1.248.11.22.1.3.1.1.1.15
hm2SigConPSTableThis table contains the configuration of all power supply states.
SEQUENCE OF Hm2SigConPSEntry
.1.3.6.1.4.1.248.11.22.1.3.1.2
hm2SigConPSEntryThe entry of the hm2SigConPSTable.
Hm2SigConPSEntry
.1.3.6.1.4.1.248.11.22.1.3.1.2.1
hm2SigConSensePSStateSets the monitoring of the power supply state.rw
HmEnabledStatus (HM2-TC-MIB)
.1.3.6.1.4.1.248.11.22.1.3.1.2.1.1
hm2SigConInterfaceTableThis table contains all variables to mask an alarm for the signalling relay, produced by a link. The index for a link corresponds with ifIndex. The table is also used for the device monitoring configuration.
SEQUENCE OF Hm2SigConInterfaceEntry
.1.3.6.1.4.1.248.11.22.1.3.1.3
hm2SigConInterfaceEntryThe entry of the hm2SigConLinkTable.
Hm2SigConInterfaceEntry
.1.3.6.1.4.1.248.11.22.1.3.1.3.1
hm2SigConSenseIfLinkAlarmIndicates whether an alarm for the signalling relay of the associated link will be produced or not, so you can mask the value of ifMauMediaAvailable.rw
HmEnabledStatus (HM2-TC-MIB)
.1.3.6.1.4.1.248.11.22.1.3.1.3.1.1
hm2SigConModuleTableThis table contains all variables to mask a module for the signaling relay. The index for a module corresponds with the slot number.
SEQUENCE OF Hm2SigConModuleEntry
.1.3.6.1.4.1.248.11.22.1.3.1.4
hm2SigConModuleEntryThe entry of the hm2SigConModuleTable.
Hm2SigConModuleEntry
.1.3.6.1.4.1.248.11.22.1.3.1.4.1
hm2SigConModIDThis index is used to identify the associated module.ro
Integer32
.1.3.6.1.4.1.248.11.22.1.3.1.4.1.1
hm2SigConSenseModuleIndicates whether an alarm for the signalling relay of the associated module will be produced or not.rw
HmEnabledStatus (HM2-TC-MIB)
.1.3.6.1.4.1.248.11.22.1.3.1.4.1.2
hm2SigConStatusTableThis table shows the current monitored entities for which there is a trap cause (hm2SigConTrapCause) active.
SEQUENCE OF Hm2SigConStatusEntry
.1.3.6.1.4.1.248.11.22.1.3.1.10
hm2SigConStatusEntryThe entry of the hm2SigConStatusTable.
Hm2SigConStatusEntry
.1.3.6.1.4.1.248.11.22.1.3.1.10.1
hm2SigConStatusIndexThis index is used to identify the occured event.
Integer32
.1.3.6.1.4.1.248.11.22.1.3.1.10.1.1
hm2SigConStatusTimeStampThis attribute shows the local system time (hm2SystemLocalTime) of occuration the event.ro
HmTimeSeconds1970 (HM2-TC-MIB)
.1.3.6.1.4.1.248.11.22.1.3.1.10.1.2
hm2SigConStatusTrapCauseThis object identifies the cause for a trap. The index of the entity which produces the trap is specified by hm2SigConTrapCauseIndex.ro
Enumeration
.1.3.6.1.4.1.248.11.22.1.3.1.10.1.3
hm2SigConStatusTrapCauseIndexThis attribute specifies the entity which produces the trap. power-supply: index of power-supply table link-failure: index of interface table temperature: 0 ext-nvm-removal: (1) sd, (2) usb, (3) serial (not supported yet) ext-nvm-not-in-sync: (1) sd, (2) usb, (3) serial (not supported yet) ring-redundancy: (1) MRP, (2) PRP, (3) HSR, (4) DLR ext-nvm-update-enabled: (1) sd, (2) usb, (3) serial (not supported yet) no-link: index of interface table 0: other errorsro
Integer32
.1.3.6.1.4.1.248.11.22.1.3.1.10.1.4
hm2DeviceMonitorGroup
OBJECT IDENTIFIER
.1.3.6.1.4.1.248.11.22.1.3.2
hm2DevMonCommonTableThis table contains all variables to configure the behavior of the signalling contacts.
SEQUENCE OF Hm2DevMonCommonEntry
.1.3.6.1.4.1.248.11.22.1.3.2.1
hm2DevMonCommonEntryThe entry of the hm2DevMonConfigTable.
Hm2DevMonCommonEntry
.1.3.6.1.4.1.248.11.22.1.3.2.1.1
hm2DevMonIDThis index is used to identify the associated device monitoring group. Currently only one group is supportedro
Integer32
.1.3.6.1.4.1.248.11.22.1.3.2.1.1.1
hm2DevMonTrapEnableDetermines whether a trap shall be sent or not when the signal contact operating state changes.rw
HmEnabledStatus (HM2-TC-MIB)
.1.3.6.1.4.1.248.11.22.1.3.2.1.1.2
hm2DevMonTrapCauseThis object identifies the cause for a trap. The index of the entity which produces the trap is specified by hm2DevMonTrapCauseIndex.ro
Enumeration
.1.3.6.1.4.1.248.11.22.1.3.2.1.1.3
hm2DevMonTrapCauseIndexThis attribute specifies the entity which produces the trap. power-supply: index of power supply table link-failure: index of interface table temperature: 0 ext-nvm-removal: (1) sd, (2) usb, (3) Serial (not supported yet) ext-nvm-not-in-sync: (1) sd, (2) usb, (3) Serial (not supported yet) ring-redundancy: (1) MRP, (2) PRP, (3), HSR, (4) DLR 0: other errorsro
Integer32
.1.3.6.1.4.1.248.11.22.1.3.2.1.1.4
hm2DevMonOperStateThis attribute shows the current operating state of the signal contact.ro
Enumeration
.1.3.6.1.4.1.248.11.22.1.3.2.1.1.5
hm2DevMonOperTimeStampThis attribute shows the local system time (hm2SystemLocalTime) of the last hm2DevMonOperState change.ro
HmTimeSeconds1970 (HM2-TC-MIB)
.1.3.6.1.4.1.248.11.22.1.3.2.1.1.6
hm2DevMonSenseLinkFailureSets the monitoring of the network connection(s).rw
HmEnabledStatus (HM2-TC-MIB)
.1.3.6.1.4.1.248.11.22.1.3.2.1.1.7
hm2DevMonSenseTemperatureSets the monitoring of the device temperature.rw
HmEnabledStatus (HM2-TC-MIB)
.1.3.6.1.4.1.248.11.22.1.3.2.1.1.8
hm2DevMonSenseFanSets the monitoring of the device fan. (currently not supported)rw
HmEnabledStatus (HM2-TC-MIB)
.1.3.6.1.4.1.248.11.22.1.3.2.1.1.9
hm2DevMonSenseModuleRemovalSets the monitoring of module removal (platform dependent).rw
HmEnabledStatus (HM2-TC-MIB)
.1.3.6.1.4.1.248.11.22.1.3.2.1.1.10
hm2DevMonSenseExtNvmRemovalSets the monitoring of the external non-volatile memory removal.rw
HmEnabledStatus (HM2-TC-MIB)
.1.3.6.1.4.1.248.11.22.1.3.2.1.1.11
hm2DevMonSenseExtNvmNotInSyncSets the monitoring whether the external non-volatile memory is in sync with the configuration in NVRAM.rw
HmEnabledStatus (HM2-TC-MIB)
.1.3.6.1.4.1.248.11.22.1.3.2.1.1.12
hm2DevMonSenseRingRedundancySets the monitoring of the ring redundancy.rw
HmEnabledStatus (HM2-TC-MIB)
.1.3.6.1.4.1.248.11.22.1.3.2.1.1.13
hm2DevMonPSTableThis table contains the configuration of all power supply states.
SEQUENCE OF Hm2DevMonPSEntry
.1.3.6.1.4.1.248.11.22.1.3.2.2
hm2DevMonPSEntryThe entry of the hm2DevMonPSTable.
Hm2DevMonPSEntry
.1.3.6.1.4.1.248.11.22.1.3.2.2.1
hm2DevMonSensePSStateSets the monitoring of the power supply state.rw
HmEnabledStatus (HM2-TC-MIB)
.1.3.6.1.4.1.248.11.22.1.3.2.2.1.1
hm2DevMonInterfaceTableThis table contains all variables to mask an alarm for the signalling relay, produced by a link. The index for a link corresponds with ifIndex. The table is also used for the device monitoring configuration.
SEQUENCE OF Hm2DevMonInterfaceEntry
.1.3.6.1.4.1.248.11.22.1.3.2.3
hm2DevMonInterfaceEntryThe entry of the hm2DevMonLinkTable.
Hm2DevMonInterfaceEntry
.1.3.6.1.4.1.248.11.22.1.3.2.3.1
hm2DevMonSenseIfLinkAlarmIndicates whether an alarm for the signalling relay of the associated link will be produced or not, so you can mask the value of ifMauMediaAvailable.rw
HmEnabledStatus (HM2-TC-MIB)
.1.3.6.1.4.1.248.11.22.1.3.2.3.1.1
hm2DevMonModuleTableThis table contains all variables to mask a module for the device status. The index for a module corresponds with the slot number.
SEQUENCE OF Hm2DevMonModuleEntry
.1.3.6.1.4.1.248.11.22.1.3.2.4
hm2DevMonModuleEntryThe entry of the hm2DevMonModuleTable.
Hm2DevMonModuleEntry
.1.3.6.1.4.1.248.11.22.1.3.2.4.1
hm2DevMonModIDThis index is used to identify the associated module.ro
Integer32
.1.3.6.1.4.1.248.11.22.1.3.2.4.1.1
hm2DevMonSenseModuleIndicates whether an alarm for the device status of the associated module will be produced or not.rw
HmEnabledStatus (HM2-TC-MIB)
.1.3.6.1.4.1.248.11.22.1.3.2.4.1.2
hm2DevMonStatusTableThis table shows the current monitored entities in the hm2DeviceMonitorGroup for which there is a trap cause (hm2DevMonStatusTrapCause) active.
SEQUENCE OF Hm2DevMonStatusEntry
.1.3.6.1.4.1.248.11.22.1.3.2.10
hm2DevMonStatusEntryThe entry of the hm2DevMonStatusTable.
Hm2DevMonStatusEntry
.1.3.6.1.4.1.248.11.22.1.3.2.10.1
hm2DevMonStatusIndexThis index is used to identify the occured event.
Integer32
.1.3.6.1.4.1.248.11.22.1.3.2.10.1.1
hm2DevMonStatusTimeStampThis attribute shows the local system time (hm2SystemLocalTime) of occuration the event.ro
HmTimeSeconds1970 (HM2-TC-MIB)
.1.3.6.1.4.1.248.11.22.1.3.2.10.1.2
hm2DevMonStatusTrapCauseThis object identifies the cause for a trap. The index of the entity which produces the trap is specified by hm2DevMonTrapCauseIndex.ro
Enumeration
.1.3.6.1.4.1.248.11.22.1.3.2.10.1.3
hm2DevMonStatusTrapCauseIndexThis attribute specifies the entity which produces the trap. power-supply: index of power supply table link-failure: index of interface table temperature: 0 ext-nvm-removal: (1) sd, (2) usb, (3) Serial (not supported yet) ext-nvm-not-in-sync: (1) sd, (2) usb, (3) Serial (not supported yet) ring-redundancy: (1) MRP, (2) PRP, (3) HSR, (4) DLR 0: other errorsro
Integer32
.1.3.6.1.4.1.248.11.22.1.3.2.10.1.4
hm2DeviceSecurityGroup
OBJECT IDENTIFIER
.1.3.6.1.4.1.248.11.22.1.3.3
hm2DevSecConfigGroup
OBJECT IDENTIFIER
.1.3.6.1.4.1.248.11.22.1.3.3.1
hm2DevSecTrapEnableDetermines whether a trap shall be sent or not, when the device security operating state changes.rw
HmEnabledStatus (HM2-TC-MIB)
.1.3.6.1.4.1.248.11.22.1.3.3.1.1
hm2DevSecTrapCauseThis object identifies the cause for a trap. The index of the entity which produces the trap is specified by hm2DevMonTrapCauseIndex.ro
Enumeration
.1.3.6.1.4.1.248.11.22.1.3.3.1.2
hm2DevSecTrapCauseIndexThis attribute specifies the entity which produces the trap. ext-nvm-update-enabled: (1) sd, (2) usb, (3) serial (not supported yet) no-link: index of interface table 0: other errors.ro
Integer32
.1.3.6.1.4.1.248.11.22.1.3.3.1.3
hm2DevSecOperStateThis attribute shows the current operating state of the signal contact.ro
Enumeration
.1.3.6.1.4.1.248.11.22.1.3.3.1.4
hm2DevSecOperTimeStampThis attribute shows the local system time (hm2SystemLocalTime) of the last hm2DevSecOperState change.ro
HmTimeSeconds1970 (HM2-TC-MIB)
.1.3.6.1.4.1.248.11.22.1.3.3.1.5
hm2DevSecSensePasswordChangeEnable or disable to check if default passwords for 'user' and 'admin' are not changed.rw
HmEnabledStatus (HM2-TC-MIB)
.1.3.6.1.4.1.248.11.22.1.3.3.1.6
hm2DevSecSensePasswordMinLengthEnable or disable to check if configured minimum password length is < 8 characters.rw
HmEnabledStatus (HM2-TC-MIB)
.1.3.6.1.4.1.248.11.22.1.3.3.1.7
hm2DevSecSensePasswordStrengthNotConfiguredEnable or disable minimum password strength to check if (1 uppercase, 1 lowercase, 1 number, 1 non-alphanumeric) is not configured.rw
HmEnabledStatus (HM2-TC-MIB)
.1.3.6.1.4.1.248.11.22.1.3.3.1.8
hm2DevSecSenseBypassPasswordStrengthEnable or disable to check if at least one user is configured to bypass strength check.rw
HmEnabledStatus (HM2-TC-MIB)
.1.3.6.1.4.1.248.11.22.1.3.3.1.9
hm2DevSecSenseTelnetEnabledEnable or disable to check if telnet is enabled on the switch.rw
HmEnabledStatus (HM2-TC-MIB)
.1.3.6.1.4.1.248.11.22.1.3.3.1.10
hm2DevSecSenseHttpEnabledEnable or disable to check if HTTP is enabled on the switch.rw
HmEnabledStatus (HM2-TC-MIB)
.1.3.6.1.4.1.248.11.22.1.3.3.1.11
hm2DevSecSenseSnmpUnsecureEnable or disable to check if SNMP v1/v2 is enabled or v3 encryption is disabled.rw
HmEnabledStatus (HM2-TC-MIB)
.1.3.6.1.4.1.248.11.22.1.3.3.1.12
hm2DevSecSenseSysmonEnabledEnable or disable to check if sysmon1 access is not disabled.rw
HmEnabledStatus (HM2-TC-MIB)
.1.3.6.1.4.1.248.11.22.1.3.3.1.13
hm2DevSecSenseExtNvmUpdateEnabledEnable or disable to check if external non-volatile memory update is not disabled.rw
HmEnabledStatus (HM2-TC-MIB)
.1.3.6.1.4.1.248.11.22.1.3.3.1.14
hm2DevSecSenseNoLinkEnabledEnable or disable to check if at least one port has no link but admin state is up.rw
HmEnabledStatus (HM2-TC-MIB)
.1.3.6.1.4.1.248.11.22.1.3.3.1.15
hm2DevSecSenseHiDiscoveryEnabledEnable or disable to check if HiDiscovery is enabled and the mode is 'read-write'.rw
HmEnabledStatus (HM2-TC-MIB)
.1.3.6.1.4.1.248.11.22.1.3.3.1.16
hm2DevSecSenseExtNvmConfigLoadUnsecureEnable or disable to check if the configuration load from external NVM is unsecure. (The configuration priority of the external NVM is set to 'first', 'second' or 'third' and the configuration encryption is not active.)rw
HmEnabledStatus (HM2-TC-MIB)
.1.3.6.1.4.1.248.11.22.1.3.3.1.17
hm2DevSecSenseIec61850MmsEnabledEnable or disable to check if IEC 61850 MMS is enabled on the switch.rw
HmEnabledStatus (HM2-TC-MIB)
.1.3.6.1.4.1.248.11.22.1.3.3.1.18
hm2DevSecSenseHttpsCertificateWarningEnable or disable to check for the presence of the auto generated self-signed HTTPS certificate.rw
HmEnabledStatus (HM2-TC-MIB)
.1.3.6.1.4.1.248.11.22.1.3.3.1.19
hm2DevSecSenseModbusTcpEnabledEnable or disable to check if Modbus/TCP server is enabled on the switch.rw
HmEnabledStatus (HM2-TC-MIB)
.1.3.6.1.4.1.248.11.22.1.3.3.1.20
hm2DevSecSenseEtherNetIpEnabledEnable or disable to check if EtherNet/IP protocol is enabled on the switch.rw
HmEnabledStatus (HM2-TC-MIB)
.1.3.6.1.4.1.248.11.22.1.3.3.1.21
hm2DevSecSenseProfinetIOEnabledEnable or disable to check if ProfinetIO protocol is enabled on the switch.rw
HmEnabledStatus (HM2-TC-MIB)
.1.3.6.1.4.1.248.11.22.1.3.3.1.22
hm2DevSecInterfaceTableThis table contains all variables to mask an alarm for the signalling relay, produced by a link. The index for a link corresponds with ifIndex. The table is also used for the device monitoring configuration.
SEQUENCE OF Hm2DevSecInterfaceEntry
.1.3.6.1.4.1.248.11.22.1.3.3.2
hm2DevSecInterfaceEntryThe entry of the hm2DevSecLinkTable.
Hm2DevSecInterfaceEntry
.1.3.6.1.4.1.248.11.22.1.3.3.2.1
hm2DevSecStatusTableThis table shows the current monitored entities in the hm2DevSecConfigGroup for which there is a trap cause (hm2DevSecStatusTrapCause) active.
SEQUENCE OF Hm2DevSecStatusEntry
.1.3.6.1.4.1.248.11.22.1.3.3.10
hm2DevSecStatusEntryThe entry of the hm2DevSecStatusTable.
Hm2DevSecStatusEntry
.1.3.6.1.4.1.248.11.22.1.3.3.10.1
hm2DevSecStatusIndexThis index is used to identify the occured event.
Integer32
.1.3.6.1.4.1.248.11.22.1.3.3.10.1.1
hm2DevSecStatusTimeStampThis attribute shows the local system time (hm2SystemLocalTime) of occuration the event.ro
HmTimeSeconds1970 (HM2-TC-MIB)
.1.3.6.1.4.1.248.11.22.1.3.3.10.1.2
hm2DevSecStatusTrapCauseThis object identifies the cause for a trap. The index of the entity which produces the trap is specified by hm2DevSecTrapCauseIndex.ro
Enumeration
.1.3.6.1.4.1.248.11.22.1.3.3.10.1.3
hm2DevSecStatusTrapCauseIndexThis attribute specifies the entity which produces the trap. ext-nvm-update-enabled: (1) sd, (2) usb, (3) serial (not supported yet) no-link: index of interface table 0: other errors.ro
Integer32
.1.3.6.1.4.1.248.11.22.1.3.3.10.1.4
hm2DiagLedGroup
OBJECT IDENTIFIER
.1.3.6.1.4.1.248.11.22.1.4
hm2LedGlobalTable.
SEQUENCE OF Hm2LedGlobalEntry
.1.3.6.1.4.1.248.11.22.1.4.1
hm2LedGlobalEntry.
Hm2LedGlobalEntry
.1.3.6.1.4.1.248.11.22.1.4.1.1
hm2LedGlobalLedType.
Hm2LedType
.1.3.6.1.4.1.248.11.22.1.4.1.1.1
hm2LedGlobalStatus.ro
Hm2LedStatus
.1.3.6.1.4.1.248.11.22.1.4.1.1.2
hm2LedPortTable.
SEQUENCE OF Hm2LedPortEntry
.1.3.6.1.4.1.248.11.22.1.4.2
hm2LedPortEntry.
Hm2LedPortEntry
.1.3.6.1.4.1.248.11.22.1.4.2.1
hm2LedPortStatus.ro
Hm2LedStatus
.1.3.6.1.4.1.248.11.22.1.4.2.1.1
hm2LedPortPoeStatus.ro
Hm2LedStatus
.1.3.6.1.4.1.248.11.22.1.4.2.1.2
hm2LedPortSignalingEnable for LED port signaling.rw
HmEnabledStatus (HM2-TC-MIB)
.1.3.6.1.4.1.248.11.22.1.4.2.1.3
hm2LedControlGroup
OBJECT IDENTIFIER
.1.3.6.1.4.1.248.11.22.1.4.3
hm2LedPortModeSwitch LED signalling between the port LEDs on front side (port panel) and the port LEDs on the back side (service panel) of the device.rw
Enumeration
.1.3.6.1.4.1.248.11.22.1.4.3.1
hm2DiagIfaceUtilizationGroup
OBJECT IDENTIFIER
.1.3.6.1.4.1.248.11.22.1.5
hm2DiagIfaceUtilizationTableThis table contains variables for each interface of the switch.
SEQUENCE OF Hm2DiagIfaceUtilizationEntry
.1.3.6.1.4.1.248.11.22.1.5.1
hm2DiagIfaceUtilizationEntryThe entry of the hm2DiagIfaceUtilizationTable.
Hm2DiagIfaceUtilizationEntry
.1.3.6.1.4.1.248.11.22.1.5.1.1
hm2DiagIfaceUtilizationThe best estimate of the mean physical layer network utilization on this interface during the last sampling interval, in hundredth of one percent. The first historyControlInterval (rfc1757) of this interface is used as sampling interval.ro
Integer32
.1.3.6.1.4.1.248.11.22.1.5.1.1.1
hm2DiagIfaceUtilizationControlIntervalThe interval in seconds over which the data is sampled for hmIfaceUtilization. This interval can be any number of seconds between 1 and 3600 (1 hour). The first historyControlInterval (rfc1757) of this interface is used as sampling interval.rw
Integer32
.1.3.6.1.4.1.248.11.22.1.5.1.1.2
hm2DiagIfaceUtilizationAlarmLowerThresholdSurveys the interface utilization hm2InfaceUtilization and generates an alarm for this interfaces, if the utilization value is below the given limit. A value of 0 disables the alarm generation.rw
Integer32
.1.3.6.1.4.1.248.11.22.1.5.1.1.3
hm2DiagIfaceUtilizationAlarmUpperThresholdSurveys the interface utilization hm2DiagIfaceUtilization and generates an alarm for this interfaces, if the given limit is exceeded. A value of 0 disables the alarm generation.rw
Integer32
.1.3.6.1.4.1.248.11.22.1.5.1.1.4
hm2DiagIfaceUtilizationAlarmConditionThe alarm condition is given (true), if the given hm2DiagIfaceUtilizationAlarmUpperThreshold limit is exceeded by the interface utilization or if the utilization value falls below hm2DiagIfaceUtilizationAlarmLowerThreshold limit. The alarm condition will be removed, when the interface utilization value falls in between hm2DiagIfaceUtilizationAlarmLowerThreshold hm2DiagIfaceUtilizationAlarmUpperThreshold.ro
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.248.11.22.1.5.1.1.5
hm2DiagCableTesterGroup
OBJECT IDENTIFIER
.1.3.6.1.4.1.248.11.22.1.6
hm2DiagCableTesterStatusStatus of the Virtual Cable Tester active(1) - Cable testing is in progress. Set to this value to start the test. success(2) - A successful test was performed. Cannot be set. failure(3) - A failure was encountered during the test. Cannot be set. uninitialized(4) - No test has been performed yet. Cannot be set.rw
Enumeration
.1.3.6.1.4.1.248.11.22.1.6.1
hm2DiagCableTesterIfIndexDetermines on which port to perform the cable test. Limited to copper based ports.rw
Unsigned32
.1.3.6.1.4.1.248.11.22.1.6.2
hm2DiagCableTesterCableTableThis table contains variables for each pair of the cable.
SEQUENCE OF Hm2DiagCableTesterCableEntry
.1.3.6.1.4.1.248.11.22.1.6.10
hm2DiagCableTesterCableEntryThe entry of the hm2DiagCableTesterCableTable.
Hm2DiagCableTesterCableEntry
.1.3.6.1.4.1.248.11.22.1.6.10.1
hm2DiagCableTesterCablePairIndex of the hm2DiagCableTesterCableTable. If a PHY does not support the measurement per pair, the first index is used to show the values.
Integer32
.1.3.6.1.4.1.248.11.22.1.6.10.1.1
hm2DiagCableTesterCableStatusIndicates the results of the Cable Test. normal(1) - The cable is working correctly. open(2) - The cable is disconnected or there is a faulty connector. short(3) - There is an electrical short in the cable. unknown(4) - No test has been performed yet, or a test is currently in progress.ro
Enumeration
.1.3.6.1.4.1.248.11.22.1.6.10.1.2
hm2DiagCableTesterCableMinimumLengthThe estimated length of the cable in meters. This value indicates the shortest length estimated. This object will return 0 if hm2DiagCableTesterStatus is not success(2) or the cable length is unknown.ro
Unsigned32
.1.3.6.1.4.1.248.11.22.1.6.10.1.3
hm2DiagCableTesterCableMaximumLengthThe estimated length of the cable in meters. This value indicates the longest length estimated. This object will return 0 if hm2DiagCableTesterStatus is not success(2) or the cable length is unknown.ro
Unsigned32
.1.3.6.1.4.1.248.11.22.1.6.10.1.4
hm2DiagCableTesterCableFailureLocationThe estimated distance in meters from the end of the cable to the failure location. This object will return 0 if hm2DiagCableTesterStatus is not success(2).ro
Unsigned32
.1.3.6.1.4.1.248.11.22.1.6.10.1.5
hm2PortMonitorGroup
OBJECT IDENTIFIER
.1.3.6.1.4.1.248.11.22.1.7
hm2PortMonitorAdminModeGlobal switch to enable / disable the port state actions, which are performed if a condition becomes truerw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.248.11.22.1.7.1
hm2PortMonitorIntfTablePort state mode interface table.
SEQUENCE OF Hm2PortMonitorIntfEntry
.1.3.6.1.4.1.248.11.22.1.7.2
hm2PortMonitorIntfEntryPort state mode interface entry.
Hm2PortMonitorIntfEntry
.1.3.6.1.4.1.248.11.22.1.7.2.1
hm2PortMonitorIntfResetPort monitor interface reset.rw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.248.11.22.1.7.2.1.2
hm2PortMonitorIntfActionInterface link disable state.rw
Enumeration
.1.3.6.1.4.1.248.11.22.1.7.2.1.3
hm2PortMonitorConditionGroup
OBJECT IDENTIFIER
.1.3.6.1.4.1.248.11.22.1.7.3
hm2PortMonitorConditionIntfTablePort state condition interface table.
SEQUENCE OF Hm2PortMonitorConditionIntfEntry
.1.3.6.1.4.1.248.11.22.1.7.3.1
hm2PortMonitorConditionIntfEntryPort state action interface entry.
Hm2PortMonitorConditionIntfEntry
.1.3.6.1.4.1.248.11.22.1.7.3.1.1
hm2PortMonitorConditionFieldCondition type field.ro
Bits
.1.3.6.1.4.1.248.11.22.1.7.3.1.1.1
hm2PortMonitorConditionLinkFlapModeInterface link flap mode.rw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.248.11.22.1.7.3.1.1.2
hm2PortMonitorConditionCrcFragmentsModeInterface CrcFragments mode.rw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.248.11.22.1.7.3.1.1.3
hm2PortMonitorConditionDuplexMismatchDetectionModeInterface duplex mismatch detection mode.rw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.248.11.22.1.7.3.1.1.4
hm2PortMonitorConditionOverloadDetectionModeInterface Overload Detection mode.rw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.248.11.22.1.7.3.1.1.5
hm2PortMonitorConditionSpeedDuplexModeInterface Speed and Duplex monitor mode.rw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.248.11.22.1.7.3.1.1.6
hm2PortMonitorConditionLinkFlapGroup
OBJECT IDENTIFIER
.1.3.6.1.4.1.248.11.22.1.7.3.2
hm2PortMonitorConditionLinkFlapIntfTablePort condition link flap interface table.
SEQUENCE OF Hm2PortMonitorConditionLinkFlapIntfEntry
.1.3.6.1.4.1.248.11.22.1.7.3.2.1
hm2PortMonitorConditionLinkFlapIntfEntryPort condition link flap interface entry.
Hm2PortMonitorConditionLinkFlapIntfEntry
.1.3.6.1.4.1.248.11.22.1.7.3.2.1.1
hm2PortMonitorConditionLinkFlapIntervalMeasure interval in seconds (1-180s) for link flap detection.rw
Integer32
.1.3.6.1.4.1.248.11.22.1.7.3.2.1.1.1
hm2PortMonitorConditionLinkFlapCountLink flap counter (1-100).rw
Integer32
.1.3.6.1.4.1.248.11.22.1.7.3.2.1.1.2
hm2PortMonitorConditionLinkFlapCountIntervalLink flap count that occured in last interval.ro
Integer32
.1.3.6.1.4.1.248.11.22.1.7.3.2.1.1.3
hm2PortMonitorConditionLinkFlapCountTotalTotal link flap count.ro
Integer32
.1.3.6.1.4.1.248.11.22.1.7.3.2.1.1.4
hm2PortMonitorConditionCrcFragmentsGroup
OBJECT IDENTIFIER
.1.3.6.1.4.1.248.11.22.1.7.3.3
hm2PortMonitorConditionCrcFragmentsIntfTablePort condition CrcFragments interface table.
SEQUENCE OF Hm2PortMonitorConditionCrcFragmentsIntfEntry
.1.3.6.1.4.1.248.11.22.1.7.3.3.1
hm2PortMonitorConditionCrcFragmentsIntfEntryPort condition CrcFragments interface entry.
Hm2PortMonitorConditionCrcFragmentsIntfEntry
.1.3.6.1.4.1.248.11.22.1.7.3.3.1.1
hm2PortMonitorConditionCrcFragmentsIntervalMeasure interval in seconds (5-180s) for CrcFragments detection.rw
Integer32
.1.3.6.1.4.1.248.11.22.1.7.3.3.1.1.1
hm2PortMonitorConditionCrcFragmentsCountCrcFragments counter (1-1000000).rw
Integer32
.1.3.6.1.4.1.248.11.22.1.7.3.3.1.1.2
hm2PortMonitorConditionCrcFragmentsCountIntervalCrcFragments count that occured in last interval.ro
Integer32
.1.3.6.1.4.1.248.11.22.1.7.3.3.1.1.3
hm2PortMonitorConditionCrcFragmentsCountTotalTotal CrcFragments count.ro
Integer32
.1.3.6.1.4.1.248.11.22.1.7.3.3.1.1.4
hm2PortMonitorConditionOverloadDetectionGroup
OBJECT IDENTIFIER
.1.3.6.1.4.1.248.11.22.1.7.3.4
hm2PortMonitorConditionOvldDetIntfTablePort condition overload detection interface table.
SEQUENCE OF Hm2PortMonitorConditionOvldDetIntfEntry
.1.3.6.1.4.1.248.11.22.1.7.3.4.1
hm2PortMonitorConditionOvldDetIntfEntryPort condition overload detection interface entry.
Hm2PortMonitorConditionOvldDetIntfEntry
.1.3.6.1.4.1.248.11.22.1.7.3.4.1.1
hm2PortMonitorConditionOvldDetTrfcTypeOverload detection condition traffic type.rw
Enumeration
.1.3.6.1.4.1.248.11.22.1.7.3.4.1.1.1
hm2PortMonitorConditionOvldDetTholdTypeOverload detection conditon threshold type.rw
Enumeration
.1.3.6.1.4.1.248.11.22.1.7.3.4.1.1.2
hm2PortMonitorConditionOvldDetLwrTholdValOverload detection condition lower threshold value.rw
Integer32
.1.3.6.1.4.1.248.11.22.1.7.3.4.1.1.3
hm2PortMonitorConditionOvldDetUprTholdValOverload detection condition upper threshold value.rw
Integer32
.1.3.6.1.4.1.248.11.22.1.7.3.4.1.1.4
hm2PortMonitorConditionOvldDetIntvlMeasure interval in seconds (1-20s) for overload detection.rw
Integer32
.1.3.6.1.4.1.248.11.22.1.7.3.4.1.1.5
hm2PortMonitorConditionOvldDetPkgCntAllAll package count from last interval.ro
Integer32
.1.3.6.1.4.1.248.11.22.1.7.3.4.1.1.6
hm2PortMonitorConditionOvldDetPkgCntBCBroadcast package count from last interval.ro
Integer32
.1.3.6.1.4.1.248.11.22.1.7.3.4.1.1.7
hm2PortMonitorConditionOvldDetPkgCntMCOverload detection condition lower threshold value.ro
Integer32
.1.3.6.1.4.1.248.11.22.1.7.3.4.1.1.8
hm2PortMonitorConditionOvldDetPkgCntKbitOverload detection condition lower threshold value.ro
Integer32
.1.3.6.1.4.1.248.11.22.1.7.3.4.1.1.9
hm2PortMonitorConditionSpeedDuplexGroup
OBJECT IDENTIFIER
.1.3.6.1.4.1.248.11.22.1.7.3.5
hm2PortMonitorConditionSpeedDuplexTablePort condition speed-duplex interface table.
SEQUENCE OF Hm2PortMonitorConditionSpeedDuplexEntry
.1.3.6.1.4.1.248.11.22.1.7.3.5.1
hm2PortMonitorConditionSpeedDuplexEntryPort condition speed-duplex interface entry.
Hm2PortMonitorConditionSpeedDuplexEntry
.1.3.6.1.4.1.248.11.22.1.7.3.5.1.1
hm2PortMonitorConditionSpeedDuplexValueSpeed and duplex combination allowed by port-monitor.rw
Bits
.1.3.6.1.4.1.248.11.22.1.7.3.5.1.1.1
hm2KbpsUnitTrafficTypeInvalidInterface {0}: 'Kbps' unit can only be used for traffic type 'all'.
OBJECT IDENTIFIER
.1.3.6.1.4.1.248.11.22.1.7.4
hm2DiagResourcesGroup
OBJECT IDENTIFIER
.1.3.6.1.4.1.248.11.22.1.8
hm2DiagEnableMeasurementEnable or disable the resources measurement If disabled, the task - needed for measurement - is also deleted.rw
HmEnabledStatus (HM2-TC-MIB)
.1.3.6.1.4.1.248.11.22.1.8.1
hm2DiagCpuResourcesGroup
OBJECT IDENTIFIER
.1.3.6.1.4.1.248.11.22.1.8.10
hm2DiagCpuUtilizationThe current cpu utilization of the device in percent.ro
Integer32
.1.3.6.1.4.1.248.11.22.1.8.10.1
hm2DiagCpuAverageUtilizationThe average cpu utilization of the device in percent, max. measured over the last 30 minutes.ro
Integer32
.1.3.6.1.4.1.248.11.22.1.8.10.2
hm2DiagCpuRunningProcessesThe current number of processes running.ro
Integer32
.1.3.6.1.4.1.248.11.22.1.8.10.3
hm2DiagCpuMaxRunningProcessesThe maximum number of processes running, max. since the last 30 minutes.ro
Integer32
.1.3.6.1.4.1.248.11.22.1.8.10.4
hm2DiagMemoryResourcesGroup
OBJECT IDENTIFIER
.1.3.6.1.4.1.248.11.22.1.8.11
hm2DiagMemoryRamAllocatedThe current allocated RAM of the device in kBytes.ro
Integer32
.1.3.6.1.4.1.248.11.22.1.8.11.1
hm2DiagMemoryRamFreeThe current free RAM of the device in kBytes.ro
Integer32
.1.3.6.1.4.1.248.11.22.1.8.11.2
hm2DiagMemoryRamAllocatedAverageThe average allocated RAM of the device in kBytes, measured over the last 30 minutes.ro
Integer32
.1.3.6.1.4.1.248.11.22.1.8.11.3
hm2DiagMemoryRamFreeAverageThe average free RAM of the device in kBytes, measured over the last 30 minutes.ro
Integer32
.1.3.6.1.4.1.248.11.22.1.8.11.4
hm2DiagMemoryRawFlashMainAllocatedThe current allocated flash memory for the main software image in kBytes.ro
Integer32
.1.3.6.1.4.1.248.11.22.1.8.11.10
hm2DiagMemoryRawFlashMainFreeThe current free flash memory for the main software image in kBytes.ro
Integer32
.1.3.6.1.4.1.248.11.22.1.8.11.11
hm2DiagMemoryFlashFileSystemAllocatedThe current allocated memory within the flash file system in kBytes.ro
Integer32
.1.3.6.1.4.1.248.11.22.1.8.11.12
hm2DiagMemoryFlashFileSystemFreeThe current free memory within the flash file system in kBytes.ro
Integer32
.1.3.6.1.4.1.248.11.22.1.8.11.13
hm2DiagNetworkResourcesGroup
OBJECT IDENTIFIER
.1.3.6.1.4.1.248.11.22.1.8.12
hm2DiagNetworkCpuIfUtilizationThe current network utilization of the internal cpu interface in percent.ro
Integer32
.1.3.6.1.4.1.248.11.22.1.8.12.1
hm2DiagNetworkCpuIfAverageUtilizationThe average network utilization of the internal cpu interface in percent, measured over the last 30 minutes.ro
Integer32
.1.3.6.1.4.1.248.11.22.1.8.12.2
hm2DiagnosticSNMPExtensionGroup
OBJECT IDENTIFIER
.1.3.6.1.4.1.248.11.22.3
hm2PortMonitorSpeedDuplexErrorReturnIndicates that the specified speed value is not supported by the port capabilities
OBJECT IDENTIFIER
.1.3.6.1.4.1.248.11.22.3.1
hm2PortMonitorCndOvldDetInconsistenTholdValIndicates that the configured upper and lower threshold values are inconsistent
OBJECT IDENTIFIER
.1.3.6.1.4.1.248.11.22.3.2
HM2-DIAGNOSTIC-MIB - SNMP MIB Reference | MIBs Explorer