CISCO-ITP-MLR-MIB
AI MIB Summary
The CISCO-ITP-MLR-MIB provides management access to Cisco IP Transfer Point (ITP) hardware and software for monitoring and controlling Multi-layer Routing (MLR) of SS7 Message Signal Units (MSUs) transported over IP. It exposes metrics and control parameters for routing decisions based on SCCP, TCAP, and MAP layer attributes (such as A/B addresses, protocol identifiers, and operation codes) to manage SMS Mobile Originated/Terminated traffic via Global Title Translation, trigger processing, and Weighted Round Robin load balancing.
The MIB for providing information about Multi-layer Routing(MLR). This MIB will provide information used to control and measure SS7 messages signalling units in a SS7 Network. Message Signalling Units are routed based on information found in the SCCP, TCAP, MAP, and MAP-user layers. It uses information from these layers to make customizable routing decision based on the following criteria.
- message A-address (origination SME)
- message B-address (destination SME)
- protocol identifier
- operation code
- called party address
- calling party address
The Cisco IP Transfer Point (ITP) is a hardware and software solution that transports SS7 traffic using IP. Each ITP node provides function similar to SS7 signalling point.
The Multi-layer SMS router will be developed in compliance to the following standards.
- GSM MAP v1, v2 and v3 MO SMS formats
- GSM MAP SMS user information for MO messages
- IS-41 MAP Mobile Originated SMS formats for
Revisions A thru D.
Acronyms and Terms A-address The originating SME of the short message.
ANSI-41 ANSI standard for defining cellular radio telecommunications inter-system operation.
B-address The destination SME of the short message.
BCH Binary Coded Hexadecimal
CdPA The SCCP Called Party Address field.
CgPA The SCCP Calling Party Address field.
GSM ITU standard for defining the Global System for Mobile communications.
GTT Global Title Translation. A function normally performed in an STP, GTT is the procedure by which the destination signalling point and subsystem number(SSN) is determined from GTA digits (i.e., the global title) present in the signalling message.
IMEI International Mobile Equipment Identity
IMSI International Mobile Station Identity or International Mobile Subscriber Identity A mobile station identifier typically used in GSM networks, but is also defined for use in IS-41 networks via IS-751.
IS-41 ANSI standard for defining cellular radio telecommunications inter-system operation. Unless otherwise stated, this refers to the IS-41-D specification.
MAP SS7 Mobile Application Part. This layer provides mobility procedures to SS7 network applications. MAP is generically used to refer to both GSM-MAP, and the IS-41-D MAP Protocol.
MC Message Center. Network element responsible for relaying and store-and-forwarding of short messages in ANSI-41 networks.
MDN Mobile Directory Number. A 10-digit North American Numbering Plan number assigned to mobile users in IS-41 networks. It may be different from the MIN.
MIN Mobile Identification Number. The 10-digit North American Numbering Plan number assigned to mobile users in IS-41 networks. It may be different from the MDN.
MLR Multi-layer Routing
MO Mobile Originated. This term is used to refer to an SMS message that is being sent from an MS to the SMSC.
MS Mobile Subscriber.
MS mobile station
MSU Message Signal Unit
MT Mobile Terminated. This term is used to refer to an SMS message that is being sent from an SMSC to an MS.
MTP Message Transfer Part MTP1 Layers 1 (physical) MTP2 Layer 2 (data) and MTP3 Layer 3 (network)
M2PA SS7 MTP2-User Peer-to-Peer Adaptation Layer specified by the IETF SIGTRAN working group, which provides SCTP/IP based links for MTP3.
M3UA SS7 MTP3 User Adaptation Layer specified by RFC 3332 for MTP3 users like ISUP.
RR Round Robin. A balancing algorithm that evenly distributes traffic among available servers.
SCCP Signalling Connection Control Part. As part of the SS7 signalling protocol, it provides connectionless and connection-oriented network services above MTP Level 3.
SCP Service Control Point. An element of an SS7-based Intelligent Network which performs various service functions, such as number translation, call setup and tear down, etc.
SCTP Stream Control Transmission Protocol. A protocol designed by the SigTran working group of the IETF to transport messages reliably over IP networks(RFC 2960). It has been specifically designed with PSTN signalling in mind, but is meant to be a general IP transport protocol.
SG Signalling Gateway. SIM Subscriber Identity Module
SME Short Message Entity. An entity that may send or receive short messages, and may be fixed or mobile.
SM Short Message
SMD-PP Short Message Delivery Point to Point.
SMS Short Message Service, as defined in GSM and IS-41-D.
SMS-MO Short Message Service Mobile Originated.
SMS-MT Short Message Service Mobile Terminated.
SMSC Short Message Service Center. Network element responsible for relaying and store-and-forwarding of short messages.
SRI Send Routing Information or Send Routing Information for Short Messages. Refers to the procedure by which an SMSC requests the HLR to send current routing information for a particular mobile user.
SRI-SM Send Routing Information Short Message
SSP Service Switching Point. An element of an SS7-based Intelligent Network that performs call origination, termination, or tandem switching.
STP Signal Transfer Point. An element of an SS7-based Intelligent Network that performs routing of the SS7 signalling.
SUA SS7 SCCP User Adaptation Layer specified by IETF SIGTRAN for SCCP users, like GSM MAP, UMTS RANAP, CDMA IS-41, CDMA IS-634, IN INAP, CAMEL CAP.
TCAP Transaction Capability Application Part. The application layer of the SS7 signalling protocol.
WRR Weighted Round Robin. A variation of the round robin algorithm that uses server weights to allow uneven distribution of traffic among a set of available servers.
Multi-layer processing consists of four basic phases as follows.
Global Title Processing Trigger Processing(primary and secondary) Rule Set Processing Result group Processing
Example scenario.
The SMS messages sent by origin SME (typically a mobile handset) and sent to the MSC controlling the area in which the origin SME resides. The MSC then initiates a dialogue with the home SMSC specified by the origin SME to route the SMS MO message.
SMS MO traffic will arrive as an SCCP packet, and the Routing Indicator(RI) may specify either 'route-on-global-title' (RI=GT) or 'route-on-subsystem' (RI=PC/SSN). The destination GT will be used to locate the global title address that applies to the destination address.
Triggers are applied directly to global title addresses. Therefore, trigger processing consists of checking for the existence of primary trigger and then processing of secondary triggers.
If the message matches a trigger then rule set processing can be performed to determine what will be modified in message and how the message will be routed. The messages may be sent to new destination address, application server, point-code or result group. Or it could be forwarded without any modification (CONTINUE) or it could be dropped (BLOCK).
Result processing balances the delivery of messages to Point-codes or application servers based on Weighted Round Robin(WRR).
********************************************
Main OID:
ciscoMlrMIB.1.3.6.1.4.1.9.9.396
179
Objects
Active
Status
7
Dependencies
Imported Objects
Objects
179 total| Object Name |
|---|
ciscoMlrMIBThe MIB for providing information about Multi-layer
Routing(MLR). This MIB will provide information used to
control and measure SS7 messages signalling units
in a SS7 Network. Message Signalling Units are routed
based on information found in the SCCP, TCAP, MAP, and
MAP-user layers. It uses information from these layers
to make customizable routing decision based on the
following criteria.
- message A-address (origination SME)
- message B-address (destination SME)
- protocol identifier
- operation code
- called party address
- calling party address
The Cisco IP Transfer Point (ITP) is a hardware
and software solution that transports SS7 traffic
using IP. Each ITP node provides function similar
to SS7 signalling point.
The Multi-layer SMS router will be developed in
compliance to the following standards.
- GSM MAP v1, v2 and v3 MO SMS formats
- GSM MAP SMS user information for MO messages
- IS-41 MAP Mobile Originated SMS formats for
Revisions A thru D.
Acronyms and Terms
A-address The originating SME of the short message.
ANSI-41 ANSI standard for defining cellular radio
telecommunications inter-system operation.
B-address The destination SME of the short message.
BCH Binary Coded Hexadecimal
CdPA The SCCP Called Party Address field.
CgPA The SCCP Calling Party Address field.
GSM ITU standard for defining the Global
System for Mobile communications.
GTT Global Title Translation. A function
normally performed in an STP, GTT is the
procedure by which the destination
signalling point and subsystem number(SSN)
is determined from GTA digits (i.e., the
global title) present in the signalling
message.
IMEI International Mobile Equipment Identity
IMSI International Mobile Station Identity or
International Mobile Subscriber Identity
A mobile station identifier typically
used in GSM networks, but is also defined
for use in IS-41 networks via IS-751.
IS-41 ANSI standard for defining cellular radio
telecommunications inter-system operation.
Unless otherwise stated, this refers to
the IS-41-D specification.
MAP SS7 Mobile Application Part. This layer
provides mobility procedures to SS7
network applications. MAP is generically
used to refer to both GSM-MAP, and the
IS-41-D MAP Protocol.
MC Message Center. Network element responsible
for relaying and store-and-forwarding of
short messages in ANSI-41 networks.
MDN Mobile Directory Number. A 10-digit North
American Numbering Plan number assigned to
mobile users in IS-41 networks. It may be
different from the MIN.
MIN Mobile Identification Number. The 10-digit
North American Numbering Plan number
assigned to mobile users in IS-41 networks.
It may be different from the MDN.
MLR Multi-layer Routing
MO Mobile Originated. This term is used to
refer to an SMS message that is being
sent from an MS to the SMSC.
MS Mobile Subscriber.
MS mobile station
MSU Message Signal Unit
MT Mobile Terminated. This term is used to
refer to an SMS message that is being
sent from an SMSC to an MS.
MTP Message Transfer Part
MTP1 Layers 1 (physical)
MTP2 Layer 2 (data) and
MTP3 Layer 3 (network)
M2PA SS7 MTP2-User Peer-to-Peer Adaptation
Layer specified by the IETF SIGTRAN
working group, which provides SCTP/IP
based links for MTP3.
M3UA SS7 MTP3 User Adaptation Layer specified
by RFC 3332 for MTP3 users like ISUP.
RR Round Robin. A balancing algorithm that
evenly distributes traffic among
available servers.
SCCP Signalling Connection Control Part. As
part of the SS7 signalling protocol, it
provides connectionless and
connection-oriented network services
above MTP Level 3.
SCP Service Control Point. An element of
an SS7-based Intelligent Network which
performs various service functions, such
as number translation, call setup
and tear down, etc.
SCTP Stream Control Transmission Protocol.
A protocol designed by the SigTran
working group of the IETF to transport
messages reliably over IP networks(RFC
2960).
It has been specifically designed with
PSTN signalling in mind, but is meant to
be a general IP transport protocol.
SG Signalling Gateway.
SIM Subscriber Identity Module
SME Short Message Entity. An entity that may
send or receive short messages, and may
be fixed or mobile.
SM Short Message
SMD-PP Short Message Delivery Point to Point.
SMS Short Message Service, as defined in
GSM and IS-41-D.
SMS-MO Short Message Service Mobile Originated.
SMS-MT Short Message Service Mobile Terminated.
SMSC Short Message Service Center. Network
element responsible for relaying and
store-and-forwarding of short messages.
SRI Send Routing Information or Send Routing
Information for Short Messages. Refers
to the procedure by which an SMSC
requests the HLR to send current routing
information for a particular mobile user.
SRI-SM Send Routing Information Short Message
SSP Service Switching Point. An element of
an SS7-based Intelligent Network that
performs call origination, termination,
or tandem switching.
STP Signal Transfer Point. An element of
an SS7-based Intelligent Network that
performs routing of the SS7 signalling.
SUA SS7 SCCP User Adaptation Layer specified
by IETF SIGTRAN for SCCP users, like
GSM MAP, UMTS RANAP, CDMA IS-41,
CDMA IS-634, IN INAP, CAMEL CAP.
TCAP Transaction Capability Application Part.
The application layer of the SS7
signalling protocol.
WRR Weighted Round Robin. A variation of
the round robin algorithm that uses
server weights to allow uneven
distribution of traffic among a set
of available servers.
Multi-layer processing consists of four basic phases
as follows.
Global Title Processing
Trigger Processing(primary and secondary)
Rule Set Processing
Result group Processing
Example scenario.
The SMS messages sent by origin SME (typically a
mobile handset) and sent to the MSC controlling the
area in which the origin SME resides. The MSC then
initiates a dialogue with the home SMSC specified
by the origin SME to route the SMS MO message.
SMS MO traffic will arrive as an SCCP packet, and
the Routing Indicator(RI) may specify either
'route-on-global-title' (RI=GT) or
'route-on-subsystem' (RI=PC/SSN). The destination
GT will be used to locate the global title address
that applies to the destination address.
Triggers are applied directly to global title
addresses. Therefore, trigger processing consists
of checking for the existence of primary trigger
and then processing of secondary triggers.
If the message matches a trigger then rule set
processing can be performed to determine what
will be modified in message and how the message
will be routed. The messages may be sent to new
destination address, application server,
point-code or result group. Or it could be forwarded
without any modification (CONTINUE) or it could be
dropped (BLOCK).
Result processing balances the delivery of messages
to Point-codes or application servers based on
Weighted Round Robin(WRR).
******************************************** MODULE-IDENTITY .1.3.6.1.4.1.9.9.396 |
ciscoMlrMIBNotifs OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.396.0 |
ciscoMlrTableLoadThis notification is generated whenever a load
operation is started or completed. Route table
configurations can be loaded by CLI requests.
In addition, route tables can loaded using
configuration statements. This allows mlr
tables to be reloaded whenever a device restarts. NOTIFICATION-TYPE .1.3.6.1.4.1.9.9.396.0.1 |
ciscoMlrMIBObjects OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.396.1 |
cmlrScalars OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.396.1.0 |
cmlrTableLoadNotifEnabledA control to enable or disable ciscoMlrTableLoad
notifications as follows:
'true' Indicates that the ciscoMlrTableLoad
notification should be generated when the load
operations is started or completed. That is,
the notification generation is enabled.
'false' Indicates that ciscoMlrTableLoad notification
generation is disabled.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.396.1.0.1 |
cmlrInstTableA table that is used to provide information and measurements
related to multi-layer routing per per signalling point. SEQUENCE OF CmlrInstTableEntry .1.3.6.1.4.1.9.9.396.1.1 |
cmlrInstTableEntryEach entry in this table provides information on each
signalling pointer supported by this device. Each
entry provides information on modification to the
configuration statements related to multi-layer
routing and general measurements. CmlrInstTableEntry .1.3.6.1.4.1.9.9.396.1.1.1 |
cmlrInstLastChangedThe value of sysUpTime at the time of the last
creation or deletion of an entry in the Multi-Layer
routing table defined for this signalling point.
If the local network management subsystem is
re-initialized, then this object contains the
sysUpTime at the time when this occurred. This value
can be used to prevent unnecessary walks of the
various take supporting multi-layer routing.ro TimeStamp (SNMPv2-TC) .1.3.6.1.4.1.9.9.396.1.1.1.1 |
cmlrInstLastLoadTimeThe value of sysUpTime at the time of the last
load of the Multi-Layer Routing table using file
format for this signalling point.ro TimeStamp (SNMPv2-TC) .1.3.6.1.4.1.9.9.396.1.1.1.2 |
cmlrInstLoadStatusThe status of the current load or status from
the prior load operation. This object will have
a value of loadInProgress while the load operation
is in progress. The cmlrInstLastLoadTime contains
a timestamp indicating when the load operation is
completed.ro CItpTcTableLoadStatus (CISCO-ITP-TC-MIB) .1.3.6.1.4.1.9.9.396.1.1.1.3 |
cmlrInstLastURLThe last URL used to load MLR table.ro CItpTcURL (CISCO-ITP-TC-MIB) .1.3.6.1.4.1.9.9.396.1.1.1.4 |
cmlrInstRoutedCountsCount of the number of times a packet was routed by
MLR. This value is incremented when packet is routed
with result type of 'asname', 'gt', 'pc' or 'pcSsn'.ro Counter32 UNITS "packets" .1.3.6.1.4.1.9.9.396.1.1.1.5 |
cmlrInstAbortCountsCount of message signal units that could not be processed
because of invalid data or were explicitly blocked as a
result of MLR processing. The message signalling units
will be discarded.ro Counter32 UNITS "packets" .1.3.6.1.4.1.9.9.396.1.1.1.6 |
cmlrInstContinueCountsCount of message signal units that were passed back to
normal SCCP processing.ro Counter32 UNITS "packets" .1.3.6.1.4.1.9.9.396.1.1.1.7 |
cmlrInstSmsMoCountsCount of message signal units with operation type
GSM-MAP SMS-MO.ro Counter32 UNITS "packets" .1.3.6.1.4.1.9.9.396.1.1.1.8 |
cmlrInstSmsMtCountsCount of message signal units with operation type
GSM-MAP SMS-MT.ro Counter32 UNITS "packets" .1.3.6.1.4.1.9.9.396.1.1.1.9 |
cmlrInstSriSmCountsCount of message signal units with operation type
GSM-MAP SRI-SM.ro Counter32 UNITS "packets" .1.3.6.1.4.1.9.9.396.1.1.1.10 |
cmlrInstSmdPpCountsCount of message signal units with operation type
ANSI-41 SMD-PP.ro Counter32 UNITS "packets" .1.3.6.1.4.1.9.9.396.1.1.1.11 |
cmlrInstAlertScCountsCount of message signal units with operation type
GSM-MAP AlertSC.ro Counter32 UNITS "packets" .1.3.6.1.4.1.9.9.396.1.1.1.12 |
cmlrInstSmsRequestCountsCount of message signal units with operation type
ANSI-41 SMSRequest.ro Counter32 UNITS "packets" .1.3.6.1.4.1.9.9.396.1.1.1.13 |
cmlrInstSmsNotifCountsCount of message signal units with operation type
ANSI-41 SMSNotification.ro Counter32 UNITS "packets" .1.3.6.1.4.1.9.9.396.1.1.1.14 |
cmlrInstUnsupSCCPmsgTypeCountsCount of message signal units received with unsupported
SCCP message type. This object counts are also included
in the cmlrInstContinueCounts object.ro Counter32 UNITS "packets" .1.3.6.1.4.1.9.9.396.1.1.1.15 |
cmlrInstUnsupSegSCCPmsgCountsCount of message signal units received with unsupported
segmented SCCP message. This object counts are also
included in the cmlrInstContinueCounts object.ro Counter32 UNITS "packets" .1.3.6.1.4.1.9.9.396.1.1.1.16 |
cmlrInstUnsupportedMsgCountsCount of message signal units received that could not be
processed because the messages contained an unsupported
command type or contents of messages was unsupported.
This object counts are also included in the
cmlrInstContinueCounts object.ro Counter32 UNITS "packets" .1.3.6.1.4.1.9.9.396.1.1.1.17 |
cmlrInstParsingErrorCountsCount of message signal units received that could not be
processed because of a parsing error. This object counts
are also included in the cmlrInstContinueCounts object.ro Counter32 UNITS "packets" .1.3.6.1.4.1.9.9.396.1.1.1.18 |
cmlrInstNoResultCountsCount of message signal units received that matched a
trigger or rule that did not specify a result. This object
counts are also included in the
cmlrInstContinueCounts object.ro Counter32 UNITS "packets" .1.3.6.1.4.1.9.9.396.1.1.1.19 |
cmlrInstResultContinueCountsCount of message signal units received that matched a
trigger or rule that specified continue for the result.
This object counts are also included in the
cmlrInstContinueCounts object.ro Counter32 UNITS "packets" .1.3.6.1.4.1.9.9.396.1.1.1.20 |
cmlrInstNoServerDiscardCountsCount of message signal units received that matched a
trigger or rule that specified a result or result group
directing MSU to application server. However, the
application server was unavailable. This object counts
are also included in the cmlrInstAbortCounts object.ro Counter32 UNITS "packets" .1.3.6.1.4.1.9.9.396.1.1.1.21 |
cmlrInstResultGttCountsCount of message signal units received that matched a
trigger or rule that specified GTT for the result. This
object counts are also included in the
cmlrInstContinueCounts object.ro Counter32 UNITS "packets" .1.3.6.1.4.1.9.9.396.1.1.1.22 |
cmlrInstUnparsedCountsCount of message signal units received that could not be
parsed due to some type of resource shortage. This object
counts are also included in the cmlrInstAbortCounts object.ro Counter32 UNITS "packets" .1.3.6.1.4.1.9.9.396.1.1.1.23 |
cmlrInstResultBlockCountsCount of message signal units received that matched a
trigger or rule that specified a result of block. This
object counts are also included in the cmlrInstAbortCounts
object.ro Counter32 UNITS "packets" .1.3.6.1.4.1.9.9.396.1.1.1.24 |
cmlrInstGTImismatchCountsCount of message signal units received that could not
be routed because of mis-match between GTI values.
This object counts are also included in the
cmlrInstAbortCounts object.ro Counter32 UNITS "packets" .1.3.6.1.4.1.9.9.396.1.1.1.25 |
cmlrInstAddrConvFailureCountsCount of message signal units received that could not
be routed because GTT address failed to convert. This
object counts are also included in the
cmlrInstAbortCounts object.ro Counter32 UNITS "packets" .1.3.6.1.4.1.9.9.396.1.1.1.26 |
cmlrInstDestUnavailableCountsCount of message signal units received that specified
a result PC or PC and SSN and the destination point-code
was unavailable. This object counts are also included
in the cmlrInstAbortCounts object.ro Counter32 UNITS "packets" .1.3.6.1.4.1.9.9.396.1.1.1.27 |
cmlrInstFailedTrigMatchCountsCount of message signal units received that was
processed and failed to mathc any trigger. This can
occur when a primary trigger specifies secondary triggers
and they fail to match. This object counts are also
included in the cmlrInstContinueCounts object.ro Counter32 UNITS "packets" .1.3.6.1.4.1.9.9.396.1.1.1.28 |
cmlrInstDiscontinuityTimeThe value of sysUpTime on the most recent occasion at
which the configuration was modified in such a way
to force a discontinuity. All counters under this
instance in the following tables will be reset when
configuration is replaced.
- cmlrTriggerTable
- cmlrSubTriggerTable
- cmlrAddressTable
- cmlrRuleTable
If no such discontinuities have occurred since the last
re-initialization of the local management subsystem,
then this object contains a zero value.ro TimeStamp (SNMPv2-TC) .1.3.6.1.4.1.9.9.396.1.1.1.29 |
cmlrInstNoServerContinueCountsCount of message signal units received that matched a
trigger or rule that specified a result or result group
directing MSU to application server. However, the
application server was unavailable. This object counts
are also included in the cmlrInstContinueCounts object.ro Counter32 UNITS "packets" .1.3.6.1.4.1.9.9.396.1.1.1.30 |
cmlrInstResultAsCountsCount of message signal units received that matched a
trigger or rule that specified result type of Application
server. This object counts are also included in the
cmlrInstRoutedCounts object.ro Counter32 UNITS "packets" .1.3.6.1.4.1.9.9.396.1.1.1.31 |
cmlrInstResultPcCountsCount of message signal units received that matched a
trigger or rule that specified result type Pointcode.
This object counts are also included in the
cmlrInstRoutedCounts object.ro Counter32 UNITS "packets" .1.3.6.1.4.1.9.9.396.1.1.1.32 |
cmlrInstResultPcSsnCountsCount of message signal units received that matched a
trigger or rule that specified pointcode and subsystem
number. This object counts are also included in the
cmlrInstRoutedCounts object.ro Counter32 UNITS "packets" .1.3.6.1.4.1.9.9.396.1.1.1.33 |
cmlrTriggerTableA table that is used to configure specific routing keys
to act as trigger for multi-layer routing. Entries are
added to this table via cmlrTriggerRowStatus in
accordance with the RowStatus convention. SEQUENCE OF CmlrTriggerTableEntry .1.3.6.1.4.1.9.9.396.1.2 |
cmlrTriggerTableEntryEach entry define a trigger to be used to perform
non-standard routing of message signalling units. Each
trigger entry contains information used to select traffic
for further processing. Therefore, the information used
to activate trigger must be unique. In addition,
information referenced in the routing keys must be defined
using objects from CISCO-ITP-GSCCP-MIB or
CISCO-ITP-GRT-MIB management information bases. CmlrTriggerTableEntry .1.3.6.1.4.1.9.9.396.1.2.1 |
cmlrTableNameA name used to define a collection of multi-layer
routing statements. CmlrName .1.3.6.1.4.1.9.9.396.1.2.1.1 |
cmlrTriggerNumberThis object specifies the index for a list of triggers
specified per routing table. CmlrId .1.3.6.1.4.1.9.9.396.1.2.1.2 |
cmlrTriggerParametersThe following options define the source and
processing of triggers.
'block' : Indicates that message signal units will be
dropped when they match the specified trigger.
When sub-trigger(secondary triggers) exist
the option will be ignored.
'continue' : Indicates that message signal units will be
processed by the normal SCCP routing.
The continue, block and ruleset are mutually
exclusive.
'matchAll': Indicates the trigger will match all
message signal unit.
'cdpa' : Indicates that the trigger is found within
the SCCP called party address field(cdpa).
'cgpa' : Indicates that the trigger is found within
the SCCP calling party address field(cgpa).
'pc' : Indicates that the trigger will be matched if
it contains the specified point-code. The
point-code within the SCCP Cdpa or CgPa will
be inspected first. If the point code is not
present, then the DPC in the routing label is
used if CdPA, and the OPC is used for CgPA.
'gt' : Indicates that the Cgpa or CdPA trigger is to
be applied to packet when routing indicator
specifies global title translation(RI=GT).
'tt' : Indicates that the translation type has been
specified in the cmlrTriggerTransType object.
'gti' : Indicates that the global title indicator has
been specified in the cmlrTriggerGti
object.
'np' : Indicates that the numbering plan has been
specified in the cmlrTriggerNp object.
'nai : Indicates that the nature of specified address
has been specified in the cmlrTriggerNai object.
'ssn' : Indicates that the subsystem number has been
in the cmlrTriggerSsn object.
'network' : Indicates the network name has been specified
in the cmlrTriggerNetwork object.
'ruleset' : Indicates the set of rules to be processed as
specified in the cmlrTriggerRuleset object.
'dpc' : Indicates that the destination point-code is
one of MTP3 trigger parameters. The DPC is
specified in the cmlrTriggerDpc object.
'opc' : Indicates that the origination point-code is
one of MTP3 trigger parameters. The OPC is
specified in the cmlrTriggerOpc object.
'opcMask': Indicates that the origination point-code is
qualified with a mask.
one of MTP3 trigger parameters. The OPC is
specified in the cmlrTriggerOpc object.
'si': Indicates that the service indicator has
been specified in the cmlrTriggerSi objectrw Bits .1.3.6.1.4.1.9.9.396.1.2.1.3 |
cmlrTriggerGtThe global title address to be matched when either the
'cdpa' or 'cgpa' bits are set in the cmlrTriggerParameters
object. This object will return a string of zero length
when the cmlrTriggerParameters 'pc' bit is set.rw CItpTcGtaLongDisplay (CISCO-ITP-TC-MIB) .1.3.6.1.4.1.9.9.396.1.2.1.4 |
cmlrTriggerTransTypeThe translation type specified within the address in the
message signal unit. This object will default to value
based on variant unless the 'tt' bit is set in
cmlrTriggerParameters object.rw CgsccpGttTransType (CISCO-ITP-GSCCP-MIB) .1.3.6.1.4.1.9.9.396.1.2.1.5 |
cmlrTriggerGtiThe global title indicator value for the global tile address
specified within the message signal unit. This object will
default to value based on variant unless the 'gti' bit is
set in cmlrTriggerParameters object.rw CgsccpGttGlobalTitleInd (CISCO-ITP-GSCCP-MIB) .1.3.6.1.4.1.9.9.396.1.2.1.6 |
cmlrTriggerNpThe numbering plan of the specified global title address.
This object will default to value based on variant unless
the 'np' bit is set in cmlrTriggerParameters object.rw CItpTcNumberingPlan (CISCO-ITP-TC-MIB) .1.3.6.1.4.1.9.9.396.1.2.1.7 |
cmlrTriggerNaiNature of Address Indicator (NAI) for GTT Selector. This
object will default to value based on variant unless the
'nai' bit is set in cmlrTriggerParameters object.rw CItpTcNAI (CISCO-ITP-TC-MIB) .1.3.6.1.4.1.9.9.396.1.2.1.8 |
cmlrTriggerPcThe point-code in variant-specific format. This
object only has meaning when the 'pc' bit is
set in the cmlrTriggerParameters object.rw CItpTcPointCode (CISCO-ITP-TC-MIB) .1.3.6.1.4.1.9.9.396.1.2.1.9 |
cmlrTriggerSsnThe subsystem number to be matched when the when the 'pc'
bit is set in the cmlrTriggerParameters object.rw CItpTcSubSystemNumber (CISCO-ITP-TC-MIB) .1.3.6.1.4.1.9.9.396.1.2.1.10 |
cmlrTriggerDpcThe destination MTP3 point-code to be matched when the when
the 'dpc' bit is set in the cmlrTriggerParameters object.rw CItpTcPointCode (CISCO-ITP-TC-MIB) .1.3.6.1.4.1.9.9.396.1.2.1.11 |
cmlrTriggerOpcThe origination MTP3 point-code to be matched when the when
the 'opc' bit is set in the cmlrTriggerParameters object.rw CItpTcPointCode (CISCO-ITP-TC-MIB) .1.3.6.1.4.1.9.9.396.1.2.1.12 |
cmlrTriggerOpcMaskThe origination MTP3 point-code mask to be applied in
combination with cmlrTriggerOpc object. The mask will
be applied when 'opcMask' bit is set in the
cmlrTriggerParameters object.rw CItpTcPointCodeMask (CISCO-ITP-TC-MIB) .1.3.6.1.4.1.9.9.396.1.2.1.13 |
cmlrTriggerSiThe Service Indicator to be matched when the when
the 'si' bit is set in the cmlrTriggerParameters object.rw CItpTcServiceIndicator (CISCO-ITP-TC-MIB) .1.3.6.1.4.1.9.9.396.1.2.1.14 |
cmlrTriggerNetworkThe network name is used to indicate the network
in which the ruleset will be invoked. This
object only has meaning when the 'network' bit is
set in the cmlrTriggerParameters object.rw CItpTcNetworkName (CISCO-ITP-TC-MIB) .1.3.6.1.4.1.9.9.396.1.2.1.15 |
cmlrTriggerRulesetSpecifies the ruleset table that should be used if
the trigger is matched and not overruled by a
secondary trigger ruleset. This object only has
meaning when the 'ruleset' bit is set in the
cmlrTriggerParameters object.rw CmlrRuleSetName .1.3.6.1.4.1.9.9.396.1.2.1.16 |
cmlrTriggerActiveThis object indicates whether this trigger is active.
The trigger will be active when the corresponding
GTA entry exists and has been linked to trigger.
'true' - Trigger is active and will be processed.
'false' - Trigger is inactive and will not be processed.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.396.1.2.1.17 |
cmlrTriggerStartDateAndTimeThe local date and time when this trigger and sub-triggers
will become active. When all bytes of octet string are
set to zero then cmlrInstStartDateAndTime does not apply.rw DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.9.9.396.1.2.1.18 |
cmlrTriggerEndDateAndTimeThe local date and time this trigger and sub-triggers
will become inactive. When all bytes of octet string are
set to zero then cmlrInstEndDateAndTime does not apply.rw DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.9.9.396.1.2.1.19 |
cmlTriggerPreliminaryMatchCountsThis counter indicates that a packet has matched the
contents of the primary trigger. This counter indicates
which triggers are causing packets to be processed by
multi-layer routing. Whether the trigger is fully
matched will be indicated by the cmlrTriggerMatchCounts
object. It is important to note that in the case where
secondary triggers do not exist the
cmlTriggerPreliminaryMatchCounts and cmlrTriggerMatchCounts
will be the same.ro Counter32 .1.3.6.1.4.1.9.9.396.1.2.1.20 |
cmlrTriggerMatchCountsThis counter indicates that a packet has matched the trigger
and the result action was performed. When a primary trigger
has secondary triggers this counter indicates that the
primary matched and at least one of the secondary triggers
matched.ro Counter32 .1.3.6.1.4.1.9.9.396.1.2.1.21 |
cmlrTriggerRowStatusThe object is used by a management station to create or
delete the row entry in cmlrTriggerTable following
the RowStatus textual convention.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.9.9.396.1.2.1.22 |
cmlrSubTriggerTableA table that is used to define additional triggers
that work in combination with values specified in
specific cmlrTriggerTable. Entries are
added to this table via cmlrSubTriggerRowStatus in
accordance with the RowStatus convention. SEQUENCE OF CmlrSubTriggerTableEntry .1.3.6.1.4.1.9.9.396.1.3 |
cmlrSubTriggerTableEntryEach entry in the cmlrSubTriggerTable works in
conjunction with a entry in cmlrTriggerTable.
The trigger address specified in cmlrSubTriggerTable
is a secondary address and both the primary address
in the cmlrTriggerTable and the secondary address
must match for the packet to be routed using the
specified ruleset.
If the corresponding entry in the cmlrTriggerTableEntry
is deleted all entries under the scope for the
primary trigger will be deleted from this table.
It is important to note that when cmlrTriggerBlock is
set to 'true' sub-triggers cannot be created under the
specified trigger(cmlrTriggerNumber). CmlrSubTriggerTableEntry .1.3.6.1.4.1.9.9.396.1.3.1 |
cmlrSubTriggerNumberThis object specifies the index for a list of secondary
triggers specified per primary trigger. CmlrId .1.3.6.1.4.1.9.9.396.1.3.1.1 |
cmlrSubTriggerParametersThe following options define the source and
processing of sub-triggers(secondary trigger).
'block' : Indicates that message signal units will be
dropped when they match the specified
secondary trigger.
'continue' : Indicates that message signal units will be
processed by the normal SCCP routing.
The continue, block and ruleset are mutually
exclusive.
'matchAll': Indicates the secondary trigger will match all
message signal unit.
'cdpa' : Indicates that the secondary trigger is found
within the SCCP called party address
field(cdpa).
'cgpa' : Indicates that the secondary trigger is found
within the SCCP calling party address
field(cgpa).
'pc' : Indicates that the secondary trigger will be
matched if it contains the specified point-code.
The point-code within the SCCP Cdpa or CgPa will
be inspected first. If the point code is not
present, then the DPC in the routing label is
used if CdPA, and the OPC is used for CgPA.
'gt' : Indicates that the Cgpa or CdPA secondary trigger
is to be applied to packet when routing indicator
specifies global title translation(RI=GT).
'tt' : Indicates that the translation type has been
specified in the cmlrSubTriggerTransType object.
'gti' : Indicates that the global title indicator has
been specified in the cmlrSubTriggerGti
object.
'np' : Indicates that the numbering plan has been
specified in the cmlrSubTriggerNp object.
'nai' : Indicates that the nature of specified address
has been specified in the cmlrSubTriggerNai
object.
'ssn' : Indicates that the subsystem number has been
in the cmlrSubTriggerSsn object.
'network' : Indicates the network name has been specified
in the cmlrSubTriggerNetwork object.
'ruleset' : Indicates the set of rules to be processed as
specified in the cmlrSubTriggerRuleset object.rw Bits .1.3.6.1.4.1.9.9.396.1.3.1.2 |
cmlrSubTriggerGtThe global title address to be matched when either the
'cdpa' or 'cgpa' bits are set in the
cmlrSubTriggerParameters object. This object will return
a string of zero length when the cmlrSubTriggerParameters
'pc' bit is set.rw CItpTcGtaLongDisplay (CISCO-ITP-TC-MIB) .1.3.6.1.4.1.9.9.396.1.3.1.4 |
cmlrSubTriggerTransTypeThe translation type specified within the address in the
message signal unit. This object will default to value
based on variant unless the 'tt' bit is set in
cmlrSubTriggerParameters object.rw CgsccpGttTransType (CISCO-ITP-GSCCP-MIB) .1.3.6.1.4.1.9.9.396.1.3.1.5 |
cmlrSubTriggerGtiThe global title indicator value for the global tile address
specified within the message signal unit. This object will
default to value based on variant unless the 'gti' bit is
set in cmlrSubTriggerParameters object.rw CgsccpGttGlobalTitleInd (CISCO-ITP-GSCCP-MIB) .1.3.6.1.4.1.9.9.396.1.3.1.6 |
cmlrSubTriggerNpThe numbering plan of the specified global title address.
This object will default to value based on variant unless
the 'np' bit is set in cmlrSubTriggerParameters object.rw CItpTcNumberingPlan (CISCO-ITP-TC-MIB) .1.3.6.1.4.1.9.9.396.1.3.1.7 |
cmlrSubTriggerNaiThe nature of specified address. This object will default
to value based on variant unless the 'nai' bit is set in
cmlrSubTriggerParameters object.rw CItpTcNAI (CISCO-ITP-TC-MIB) .1.3.6.1.4.1.9.9.396.1.3.1.8 |
cmlrSubTriggerPcThe point-code in variant-specific format. This
object only has meaning when the 'pc' bit is
set in the cmlrSubTriggerParameters object.rw CItpTcPointCode (CISCO-ITP-TC-MIB) .1.3.6.1.4.1.9.9.396.1.3.1.9 |
cmlrSubTriggerSsnThe subsystem number to be matched when the when the 'pc' bit
is set in the cmlrSubTriggerParameters object.rw CItpTcSubSystemNumber (CISCO-ITP-TC-MIB) .1.3.6.1.4.1.9.9.396.1.3.1.10 |
cmlrSubTriggerNetworkThe network name is used to indicate the network
in which the ruleset will be invoked. This
object only has meaning when the 'network' bit is
set in the cmlrSubTriggerParameters object.rw CItpTcNetworkName (CISCO-ITP-TC-MIB) .1.3.6.1.4.1.9.9.396.1.3.1.11 |
cmlrSubTriggerRulesetSpecifies the ruleset table that should be used if
the trigger is matched and not overruled by a
secondary trigger ruleset. This object only has
meaning when the 'ruleset' bit is set in the
cmlrSubTriggerParameters object.rw CmlrRuleSetName .1.3.6.1.4.1.9.9.396.1.3.1.12 |
cmlrSubTriggerMatchCountsCount of the number of times secondary trigger was matched.ro Counter32 .1.3.6.1.4.1.9.9.396.1.3.1.13 |
cmlrSubTriggerRowStatusThe object is used by a management station to create or
delete the row entry in cmlrSubTriggerTable following
the RowStatus textual convention.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.9.9.396.1.3.1.14 |
cmlrAddressTableA table used to create a collection of addresses that
can be searched for exact or best matches.
Entries are added to this table via cmlrAddressRowStatus in
accordance with the RowStatus convention. SEQUENCE OF CmlrAddressTableEntry .1.3.6.1.4.1.9.9.396.1.4 |
cmlrAddressTableEntryEach entry in the cmlrAddressTable is used to search
for matches within a messages signalling unit.
Message signalling that match a particular rule can
be directed to cmlrAddressTable to allow MSU to be
directed or modified based on address information.
The table is searched using information specified in
the rule in cmlrRuleTable Table. CmlrAddressTableEntry .1.3.6.1.4.1.9.9.396.1.4.1 |
cmlrAddressTableNameA name used to define a collection of addresses used to
route and modify messages signalling units. CmlrName .1.3.6.1.4.1.9.9.396.1.4.1.1 |
cmlrAddressTypeThe type of addresses in the address tables.
The different types will be used to determine
how to format and convert cmlrAddressDigits. CmlrAddressType .1.3.6.1.4.1.9.9.396.1.4.1.2 |
cmlrAddressDigitsThe digits of the address in following formats as
indicated by cmlrAddressType object.
'hexadecimal' - The digits are hexadecimal digits specified
in ASCII as follows.
'0123456789ABCDEF' CmlrAddressDigits .1.3.6.1.4.1.9.9.396.1.4.1.3 |
cmlrAddressExactMatchThis object indicates that the address specified by
cmlrAddressDigits object must exactly match value
in message signalling unit.
'true' - Exact match is specified.
'false' - Best match is specified. TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.396.1.4.1.4 |
cmlrAddressResultParametersMany of the result parameter used in the processing of
address table have default values. These values are
determined by a combination of variant and operation
type. This object will be provide information which
parameter used in setting results have been specified
as follows.
'network' : cmlrAddressSetResultNetwork
'octet' : cmlrAddressSetResultOctet
'tranType' : cmlrAddressResultTransType
'gti' : cmlrAddressResultGti
'np' : cmlrAddressResultNp
'nai' : cmlrAddressResultNai
'pc' : cmlrAddressResultPc
'ssn' : cmlrAddressResultSsnrw CmlrResultParameters .1.3.6.1.4.1.9.9.396.1.4.1.5 |
cmlrAddressResultNetworkThe network name is used to indicate the network in which
the result operation will be performed.rw CItpTcNetworkName (CISCO-ITP-TC-MIB) .1.3.6.1.4.1.9.9.396.1.4.1.6 |
cmlrAddressResultTypeSpecified the type of information to be placed into the
message signal unit or how the it will be processed.rw CmlrResultType .1.3.6.1.4.1.9.9.396.1.4.1.7 |
cmlrAddressResultOctetInformation to be placed in the message signal
unit based on the value specified by the
cmlrAddressSetResultType object. When the
cmlrAddressSetResultType object is set to 'pc'
or 'none' this object will not be used in the
result processing and will have a length of
zero.rw CmlrResultOctet .1.3.6.1.4.1.9.9.396.1.4.1.8 |
cmlrAddressResultTransTypeThe translation type specified within the address in the
message signal unit. This object only applies when the
cmlrAddressSetResultType is set to 'gt' value.rw CgsccpGttTransType (CISCO-ITP-GSCCP-MIB) .1.3.6.1.4.1.9.9.396.1.4.1.9 |
cmlrAddressResultGtiThe global title indicator value for the global tile address
specified within the message signal unit. This object only
applies when the cmlrAddressSetResultType is set to
'gt' value.rw CgsccpGttGlobalTitleInd (CISCO-ITP-GSCCP-MIB) .1.3.6.1.4.1.9.9.396.1.4.1.10 |
cmlrAddressResultNpThe numbering plan for the global tile address specified
within the message signal unit. This object only applies
when the cmlrAddressSetResultType is set to 'gt' value.rw CItpTcNumberingPlan (CISCO-ITP-TC-MIB) .1.3.6.1.4.1.9.9.396.1.4.1.11 |
cmlrAddressResultNaiThe nature of specified address for the global tile
address specified within the message signal unit. This
object only applies when the cmlrAddressSetResultType is
set to 'gt' value.rw CItpTcNAI (CISCO-ITP-TC-MIB) .1.3.6.1.4.1.9.9.396.1.4.1.12 |
cmlrAddressResultPcThe point-code to be place in the message signal unit. This
object only applies when the cmlrAddressResultType is set
to 'pc' value.rw CItpTcPointCode (CISCO-ITP-TC-MIB) .1.3.6.1.4.1.9.9.396.1.4.1.13 |
cmlrAddressResultSsnThe subsystem number to be place in the message signal unit.
This object only applies when the cmlrAddressResultType is set
to 'ssn' value.rw CItpTcSubSystemNumber (CISCO-ITP-TC-MIB) .1.3.6.1.4.1.9.9.396.1.4.1.14 |
cmlrAddressMatchCountsCount of the number of times address was matched. This counter
is only incremented when rule matches.ro Counter32 .1.3.6.1.4.1.9.9.396.1.4.1.15 |
cmlrAddressRowStatusThe object is used by a management station to create or
delete the row entry in cmlrAddressTable following
the RowStatus textual convention.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.9.9.396.1.4.1.16 |
cmlrRuleSetTableA table that is used to specify attributes of an
application-layer message to be matched and the resulting
behavior for handling the message. Entries are added to
this table via cmlrRuleSetRowStatus in accordance with the
RowStatus convention. SEQUENCE OF CmlrRuleSetTableEntry .1.3.6.1.4.1.9.9.396.1.5 |
cmlrRuleSetTableEntryEach entry in this table represents a set of addresses
used to perform non-standard routing of messages
signalling units.. CmlrRuleSetTableEntry .1.3.6.1.4.1.9.9.396.1.5.1 |
cmlrRuleSetNameA name used to define a set rules used to transform
traffic. CmlrRuleSetName .1.3.6.1.4.1.9.9.396.1.5.1.1 |
cmlrRuleSetSegmentedThis object indicates whether segmented messages will be
processed by rules contained in this ruleset.
'true' - Segmented messages will be processed.
'false' - Segmented messages will not be processed.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.396.1.5.1.2 |
cmlrRuleSetProtocolThe object is used to establish a default protocol
type for all rules within the rule set. If this
object is set to 'none' will default to protocol
specified by variant.rw CmlrRuleProtocol .1.3.6.1.4.1.9.9.396.1.5.1.3 |
cmlrRuleSetSearchTypeDefines how the rules with the ruleset will be search
as follows.
'seq' : Rules will be processed in ascending order
based on the value of the cmlrRuleNumber
object
'bestMatch' : Rules will be processed using a combination
of operation and order number to reduce cost of
locating rule providing best match.rw Enumeration .1.3.6.1.4.1.9.9.396.1.5.1.4 |
cmlrRuleSetStartDateAndTimeThe local date and time when this trigger and sub-triggers
will become active. When the value is null then the
cmlrInstStartDateAndTime does not apply.rw DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.9.9.396.1.5.1.5 |
cmlrRuleSetEndDateAndTimeThe local date and time this trigger and sub-triggers
will become inactive. When the value is null then the
cmlrInstEndDateAndTime does not apply.rw DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.9.9.396.1.5.1.6 |
cmlrRuleSetRowStatusThe object is used by a management station to create or
delete the row entry in cmlrRuleSetTable following
the RowStatus textual convention.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.9.9.396.1.5.1.7 |
cmlrRuleTableA table that is used to specify attributes of an
application-layer message to be matched and the resulting
behavior for handling the message. Entries are
added to this table via cmlrRuleRowStatus in
accordance with the RowStatus convention. SEQUENCE OF CmlrRuleTableEntry .1.3.6.1.4.1.9.9.396.1.6 |
cmlrRuleTableEntryEntries in this table are searched in the specified order
defined but cmlrRuleNumber object
| operation | ANSI-41 | GSP-MAP |
| alertsc | | X |
| smdpp | X | |
| sms-mo | | X |
| sms-mt | | X |
| smsnot | X | |
| smsreq | X | |
| sri-sm | | X |
Rule parameters by operation
| operation | sme | smsc | | |port|
| |-|-| | ||
| |dest|orig|orig|dest|pid|tid|dest|
-|
| smdPp | X | X | | | | X | |
| smsReq | X | | | | | X | |
| smsNotify | X | | | | | X | |
| smsMo | X | X | | X | X | | X |
| smsMt | X | X | X | | X | | X |
| sriSm | X | | X | | | | |
| altertSc | X | | | X | | | |
| all | | | | | | | |
Parameters format by operation
| operation |digit | | |
| |length|dest-sme-addr-type |dest-sme-addr-type|
|alertSc |1-16 |noa/np defaults to | specific np/noa |
| | |International/E.164 | |
| | | | |
|smdPp |1-20 | | |
| | | | |
|smsMo |1-20 |noa/np defaults to | specific np/noa |
| | |International/E.164 | |
| | | | |
|smsMt |1-20 |noa/np defaults to | specific np/noa |
| | |International/E.164 | |
| | | | |
|smsNotif |1-20 | | |
| | | | |
|smsReq |1-20 | | |
| | | | |
|sriSm |1-16 |noa/np defaults to | specific np/noa |
| | |International/E.164 | |
| | | | | CmlrRuleTableEntry .1.3.6.1.4.1.9.9.396.1.6.1 |
cmlrRuleNumberThis object specifies the index for a list of secondary
triggers specified per routing table. The trigger will be
processed in ascending order. CmlrId .1.3.6.1.4.1.9.9.396.1.6.1.1 |
cmlrRuleOperationTypeThe list of possible operation types.
'unknown' : undefined operation type.
'alertSc' : Used to identify AlertServiceCenter request
messages in GSM MAP.
'smdPp' : Used to identify SMS DeliveryPointToPoint
request messages for the GSM MAP and ANSI-41.
'smsMo' : Used to identify SMS MO request messages
for the GSM MAP and ANSI-41.
'smsMt' : Used to identify SMS MT request messages
for the GSM MAP and ANSI-41.
'smsReq' : Used to identify the SMSRequest request messages
within ANSI-41.
'sriSm' : Used to identify SRI SM request messages
in GSM MAP and SMSRequest messages
in ANSI-41.
'smsNotify' : Used to identify Alert Service Center
messages in GSM MAP and SMSNotification
messages in ANSI-41.
'all' : Used to identify a match of any valid
operation code.rw Enumeration .1.3.6.1.4.1.9.9.396.1.6.1.2 |
cmlrRuleProtocolProtocol used to examine message.
'none' : Will use protocol specified in cmlrRuleSetProtocol
object.
'gsmMap' : Global system for mobile communications
Mobile Application Part operations should
be matched by this rule.
'is41' : Indicates that only ANSI-41 operations
should be matched by this rule.rw CmlrRuleProtocol .1.3.6.1.4.1.9.9.396.1.6.1.3 |
cmlrRuleInputParametersMany of the parameter used in the processing of rules
have default values. These values are determined
by a combination of variant and operation type. This
object will be provide information which parameter has
been specified as follows.
'destPort' : Indicates that the destination Port number
is specified in the cmlrRuleDestPort
object.
'destSmeGta' : Indicates that a global title address is
specified in the cmlrRuleDestSmeGta object.
'destSmeExact': Indicates that the cmlrRuleDestSmeGta
address must be an exact match.
'destSmeNai' : Indicates that the nature of specified
address is specified in the
cmlrRuleDestSmeNai object.
'destSmeNp' : Indicates that the numbering plan is
specified in the cmlrRuleDestSmeNp object.
'destSmeImsi' : Indicates that the address specified in the
International Mobile Subscriber
Identification address. This indicator
applies to the cmlrRuleDestSmeGta object.
'destSmeMin' : Indicates that the address specified in the
Mobile Identification Number. This indicator
applies to the cmlrRuleDestSmeGta object.
'destSmscGta' : Indicates that a global title address is
specified in the cmlrRuleDestSmscGta object.
'destSmscExact':Indicates that the cmlrRuleDestSmscGta
address must be an exact match.
'destSmscNai' : Indicates that the nature of specified
address is specified in the
cmlrRuleDestSmscNai object.
'destSmscNp' : Indicates that the numbering plan is
specified in the cmlrRuleDestSmscNp object.
'origSmeGta' : Indicates that a global title address is
specified in the cmlrRuleOrigSmeGta object.
'origSmeExact': Indicates that the cmlrRuleOrigSmeGta
address must be an exact match.
'origSmeNai' : Indicates that the nature of specified
address is specified in the
cmlrRuleOrigSmeNai object.
'origSmeNp' : Indicates that the numbering plan is
specified in the cmlrRuleOrigSmeNp object.
'origSmscGta' : Indicates that a global title address is
specified in the cmlrRuleOrigSmscGta object.
'origSmscExact':Indicates that the cmlrRuleOrigSmeGta
address must be an exact match.
'origSmscNai' : Indicates that the nature of specified
address is specified in the
cmlrRuleOrigSmscNai object.
'origSmscNp' : Indicates that the numbering plan is
specified in the cmlrRuleOrigSmscNp object.
'pid' : Indicates that the Protocol Identifier has
been specified in the cmlrRuleProtocolId
object.
'tid' : Indicates that the Teleservice Identifier
has been specified in the
cmlrRuleTeleserviceId object.
'default' : Indicates the processing of messages that
match the specified operation_name only.
'destSmeTable': A table of destination short message entity
addresses. The name of the table is
specified in the cmlrRuleAddressTable object.
'origSmeTable': A table of origination short message entity
addresses. The name of the table is
specified in the cmlrRuleOrigAddressTable
object.
'destSmeMinDigits'
: Minimum number global title address digits
specified in the cmlrRuleDestSmeGta object
using the cmlrRuleDestSmeMinDigits object.
'destSmeMaxDigits'
: Maximum number global title address digits
specified in the cmlrRuleDestSmeGta object
using the cmlrRuleDestSmeMaxDigits object.
'destSmeTableImsi'
: Indicates that the addresses specified in the
cmlrRuleAddressTable are International Mobile
Subscriber Identification addresses.
'destSmeTableNai'
: Indicates that the all nature of specified
address is specified in the
cmlrRuleDestSmeTableNai object.
'destSmeTableNp'
: Indicates that the numbering plan is
specified in the cmlrRuleDestSmeTableNp
object.
'destSmscMinDigits'
: Minimum number global title address digits
specified in the cmlrRuleDestSmscGta object
using the cmlrRuleDestSmscMinDigits object.
'destSmscMaxDigits'
: Maximum number global title address digits
specified in the cmlrRuleDestSmscGta object
using the cmlrRuleDestSmscMaxDigits object.
'origSmeMinDigits'
: Minimum number global title address digits
specified in the cmlrRuleOrigSmeGta object
using the cmlrRuleOrigSmeMinDigits object.
'origSmeMaxDigits'
: Maximum number global title address digits
specified in the cmlrRuleOrigSmeGta object
using the cmlrRuleOrigSmeMaxDigits object.
'origSmeTableNai'
: Indicates that the all nature of specified
address is specified in the
cmlrRuleOrigSmeTableNai object.
'origSmeTableNp'
: Indicates that the numbering plan is
specified in the cmlrRuleOrigSmeTableNp
object.
'origImsiGta' : Indicates that a global title address is
specified in the cmlrRuleDestSmeGta object.
'origImsiExact'
: Indicates that the cmlrRuleDestSmeGta
address must be an exact match.
'origImsiNai' : Indicates that the nature of specified
address is specified in the
cmlrRuleDestSmeNai object.
'origImsiNp' : Indicates that the numbering plan is
specified in the cmlrRuleDestSmeNp object.
'origImsiMinDigits'
: Minimum number global title address digits
specified in the cmlrRuleOrigImsiGta
object using the cmlrRuleOrigImsiMinDigits
object.
'origImsiMaxDigits'
: Maximum number global title address digits
specified in the cmlrRuleOrigImsiGta object
using the cmlrRuleOrigImsiMaxDigits object.
'origImsiUnknown'
: Indicates that the rule can match when packets
do not contain the origination IMSI address.
That is, when the address is unknown or
unspecified. The IMSI address is only
specified in map version 3. Therefore, the
packets using version 1 or 2 when
match when this parameter is specified.
'origImsiTable'
: A table of origination IMSI addresses. The
name of the table is specified in the
cmlrRuleOrigImsiTable object.
'origSmscMinDigits'
: Minimum number global title address digits
specified in the cmlrRuleOrigSmscGta object
using the cmlrRuleOrigSmscMinDigits object.
'origSmscMaxDigits'
: Maximum number global title address digits
specified in the cmlrRuleOrigSmscGta object
using the cmlrRuleOrigSmscMaxDigits object.
'multiMessageDialog'
: Indicates that this rules applies to packet
that are part of multiple message dialogs.rw Bits .1.3.6.1.4.1.9.9.396.1.6.1.4 |
cmlrRuleDestPortA destination application port number. The value of the
port number maps to the values specified in the User
Data Header (UDH) of the SMS message.
This object only applies when the 'destPort' bit is
set in the cmlrRuleInputParameters object.rw Unsigned32 .1.3.6.1.4.1.9.9.396.1.6.1.5 |
cmlrRuleDestSmeGtaThe destination short message entity global title address.
When the length of the global title address is zero it
specified a wildcard match and all global title will
match GTA clause of rule.
This object only applies when the 'destSmeGta' bit is
set in the cmlrRuleInputParameters object.rw CItpTcGtaLongDisplay (CISCO-ITP-TC-MIB) .1.3.6.1.4.1.9.9.396.1.6.1.6 |
cmlrRuleDestSmeNaiThe nature of specified address for the destination short
message entity global title address specified within the
message signal unit.
This object only applies when the 'destSmeNai' bit is
set in the cmlrRuleInputParameters object.rw CItpTcNAI (CISCO-ITP-TC-MIB) .1.3.6.1.4.1.9.9.396.1.6.1.7 |
cmlrRuleDestSmeNpThe numbering plan for the destination short message
entity global title address specified within the message
signal unit.
This object only applies when the 'destSmeNp' bit is
set in the cmlrRuleInputParameters object.rw CItpTcNumberingPlan (CISCO-ITP-TC-MIB) .1.3.6.1.4.1.9.9.396.1.6.1.8 |
cmlrRuleDestSmscGtaThe destination short message service center global title
address.
When the length of the global title address is zero it
specified a wildcard match and all global title will
match GTA clause of rule.
This object only applies when the 'destSmscGta' bit is
set in the cmlrRuleInputParameters object.rw CItpTcGtaLongDisplay (CISCO-ITP-TC-MIB) .1.3.6.1.4.1.9.9.396.1.6.1.9 |
cmlrRuleDestSmscNaiThe nature of specified address for the destination short
message service center global title address specified
within the message signal unit.
This object only applies when the 'destSmscNai' bit is
set in the cmlrRuleInputParameters object.rw CItpTcNAI (CISCO-ITP-TC-MIB) .1.3.6.1.4.1.9.9.396.1.6.1.10 |
cmlrRuleDestSmscNpThe numbering plan for the destination short message
service center global title address specified within the
message signal unit.
This object only applies when the 'destSmscNp' bit is
set in the cmlrRuleInputParameters object.rw CItpTcNumberingPlan (CISCO-ITP-TC-MIB) .1.3.6.1.4.1.9.9.396.1.6.1.11 |
cmlrRuleOrigSmeGtaThe origination short message entity global title address.
When the length of the global title address is zero it
specified a wildcard match and all global title will
match GTA clause of rule.
This object only applies when the 'origSmeGta' bit is
set in the cmlrRuleInputParameters object.rw CItpTcGtaLongDisplay (CISCO-ITP-TC-MIB) .1.3.6.1.4.1.9.9.396.1.6.1.12 |
cmlrRuleOrigSmeNaiThe nature of specified address for the origination short
message entity global title address specified within the
message signal unit.
This object only applies when the 'origSmeNai' bit is
set in the cmlrRuleInputParameters object.rw CItpTcNAI (CISCO-ITP-TC-MIB) .1.3.6.1.4.1.9.9.396.1.6.1.13 |
cmlrRuleOrigSmeNpThe numbering plan for the origination short message
entity global title address specified within the message
signal unit.
This object only applies when the 'origSmeNp' bit is
set in the cmlrRuleInputParameters object.rw CItpTcNumberingPlan (CISCO-ITP-TC-MIB) .1.3.6.1.4.1.9.9.396.1.6.1.14 |
cmlrRuleOrigSmscGtaThe origination short message service center global title
address.
When the length of the global title address is zero it
specified a wildcard match and all global title will
match GTA clause of rule.
This object only applies when the 'origSmscGta' bit is
set in the cmlrRuleInputParameters object.rw CItpTcGtaLongDisplay (CISCO-ITP-TC-MIB) .1.3.6.1.4.1.9.9.396.1.6.1.15 |
cmlrRuleOrigSmscNaiThe nature of specified address for the origination short
message service center global title address specified
within the message signal unit.
This object only applies when the 'origSmscNai' bit is
set in the cmlrRuleInputParameters object.rw CItpTcNAI (CISCO-ITP-TC-MIB) .1.3.6.1.4.1.9.9.396.1.6.1.16 |
cmlrRuleOrigSmscNpThe numbering plan for the origination short message
service center global title address specified within the
message signal unit.
This object only applies when the 'origSmscNp' bit is
set in the cmlrRuleInputParameters object.rw CItpTcNumberingPlan (CISCO-ITP-TC-MIB) .1.3.6.1.4.1.9.9.396.1.6.1.17 |
cmlrRuleProtocolIdThe protocol identifier value used for the 'smsMo and
'smsMt' operations specified by the
cmlrRuleParmsOperationType object.
The value of the cmlrRuleParmsMatchPid object maps to the
values specified for the TP-PID SMS parameter.
This object only applies when the 'pid' bit is
set in the cmlrRuleInputParameters object.rw Unsigned32 .1.3.6.1.4.1.9.9.396.1.6.1.18 |
cmlrRuleTeleserviceIdThe Teleservice identifier value for the following types
of operations specified by the cmlrRuleParmsOperationType
object.
'smdPp'
'smsMo'
'smsMt'
'smsNotify'
The value of the cmlrRuleParmsMatchTid object maps to the
values specified for the SMS_TeleserviceIdentifier
parameter in ANSI-41.
This object only applies when the 'tid' bit is
set in the cmlrRuleInputParameters object.rw Unsigned32 .1.3.6.1.4.1.9.9.396.1.6.1.19 |
cmlrRuleAddressTableThe name of the entry in the cmlrAddressTable that will be
searched for matches. The table will be search for the
following types of addresses based on values set in the
cmlrRuleInputParameters object.
This object only applies when the 'destSmeTable' bit is
set in the cmlrRuleInputParameters object.rw CmlrName .1.3.6.1.4.1.9.9.396.1.6.1.20 |
cmlrRuleResultParametersMany of the parameter used in the processing of rules
have default values. These values are determined
by a combination of variant and operation type. This
object will be provide information on which parameter
have been specified as follows.
'network' : cmlrRuleSetResultNetwork
'octet' : cmlrRuleSetResultOctet
'tranType' : cmlrRuleResultTransType
'gti' : cmlrRuleResultGti
'np' : cmlrRuleResultNp
'nai' : cmlrRuleResultNai
'pc' : cmlrRuleResultPc
'ssn' : cmlrRuleResultSsnrw CmlrResultParameters .1.3.6.1.4.1.9.9.396.1.6.1.21 |
cmlrRuleResultNetworkThe network name is used to indicate the network in which
the result operation will be performed.rw CItpTcNetworkName (CISCO-ITP-TC-MIB) .1.3.6.1.4.1.9.9.396.1.6.1.22 |
cmlrRuleResultTypeSpecified the type of information to be placed
into the message signal unit or how the it
will be processed.rw CmlrResultType .1.3.6.1.4.1.9.9.396.1.6.1.23 |
cmlrRuleResultOctetInformation to be placed in the message signal
unit based on the value specified by the
cmlrRuleSetResultType object. When the
cmlrRuleSetResultType object is set to 'pc'
or 'none' this object will not be used in the
result processing and will have a length of
zero.rw CmlrResultOctet .1.3.6.1.4.1.9.9.396.1.6.1.24 |
cmlrRuleResultTransTypeThe translation type specified within the address in the
message signal unit. This object only applies when the
cmlrRuleSetResultType is set to 'gt' value.rw CgsccpGttTransType (CISCO-ITP-GSCCP-MIB) .1.3.6.1.4.1.9.9.396.1.6.1.25 |
cmlrRuleResultGtiThe global title indicator value for the global tile address
specified within the message signal unit. This object only
applies when the cmlrRuleSetResultType is set to
'gt' value.rw CgsccpGttGlobalTitleInd (CISCO-ITP-GSCCP-MIB) .1.3.6.1.4.1.9.9.396.1.6.1.26 |
cmlrRuleResultNpThe numbering plan for the global tile address specified
within the message signal unit. This object only applies
when the cmlrRuleSetResultType is set to 'gt' value.rw CItpTcNumberingPlan (CISCO-ITP-TC-MIB) .1.3.6.1.4.1.9.9.396.1.6.1.27 |
cmlrRuleResultNaiThe nature of specified address for the global tile
address specified within the message signal unit. This
object only applies when the cmlrRuleSetResultType is
set to 'gt' value.rw CItpTcNAI (CISCO-ITP-TC-MIB) .1.3.6.1.4.1.9.9.396.1.6.1.28 |
cmlrRuleResultPcThe point-code to be place in the message signal unit. This
object only applies when the cmlrRuleResultType is set
to 'pc' value.rw CItpTcPointCode (CISCO-ITP-TC-MIB) .1.3.6.1.4.1.9.9.396.1.6.1.29 |
cmlrRuleResultSsnThe subsytem number to be place in the message signal unit.
This object only applies when the cmlrRuleResultType is set
to 'ssn' value.rw CItpTcSubSystemNumber (CISCO-ITP-TC-MIB) .1.3.6.1.4.1.9.9.396.1.6.1.30 |
cmlrRuleMatchCountsCount of the number of times this rule was matched.ro Counter32 .1.3.6.1.4.1.9.9.396.1.6.1.31 |
cmlrRuleRowStatusThe object is used by a management station to create or
delete the row entry in cmlrRuleTable following
the RowStatus textual convention.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.9.9.396.1.6.1.32 |
cmlrRuleOrigAddressTableThe name of the entry in the cmlrAddressTable that will be
searched for matches. The table will be search for the
following types of addresses based on values set in the
cmlrRuleInputParameters object.
This object only applies when the 'origSmeTable' bit is
set in the cmlrRuleInputParameters object.rw CmlrName .1.3.6.1.4.1.9.9.396.1.6.1.33 |
cmlrRuleDestSmeMinDigitsSpecifies the minimum number of digits that the global
title address specified by the cmlrRuleDestSmeGta object
can contain for rule to match.
This object only applies when the 'destSmeMinDigits' bit is
set in the cmlrRuleInputParameters object.rw CmlrMinimumDigits .1.3.6.1.4.1.9.9.396.1.6.1.34 |
cmlrRuleDestSmeMaxDigitsSpecifies the maximum number of digits that the global
title address specified by the cmlrRuleDestSmeGta object
can contain for rule to match.
This object only applies when the 'destSmeMaxDigits' bit is
set in the cmlrRuleInputParameters object.rw CmlrMaximumDigits .1.3.6.1.4.1.9.9.396.1.6.1.35 |
cmlrRuleDestSmeTableNaiThe nature of specified address for the global tile
address specified within the message signal unit. This
object only applies when the 'destSmeTableNai' bit is
set in the cmlrRuleInputParameters object.
When operation type, cmlrRuleOperationType is 'smsMt'
this object does not apply.rw CItpTcNAI (CISCO-ITP-TC-MIB) .1.3.6.1.4.1.9.9.396.1.6.1.36 |
cmlrRuleDestSmeTableNpThe numbering plan for the destination short message
service center global title address specified within the
message signal unit.
This object only applies when the 'destSmeTableNp' bit is
set in the cmlrRuleInputParameters object.
When operation type, cmlrRuleOperationType is 'smsMt'
this object does not apply.rw CItpTcNumberingPlan (CISCO-ITP-TC-MIB) .1.3.6.1.4.1.9.9.396.1.6.1.37 |
cmlrRuleDestSmscMinDigitsSpecifies the minimum number of digits that the global
title address specified by the cmlrRuleDestSmscGta object
can contain for rule to match.
This object only applies when the 'destSmscMinDigits' bit is
set in the cmlrRuleInputParameters object.rw CmlrMinimumDigits .1.3.6.1.4.1.9.9.396.1.6.1.38 |
cmlrRuleDestSmscMaxDigitsSpecifies the maximum number of digits that the global
title address specified by the cmlrRuleDestSmscGta object
can contain for rule to match.
This object only applies when the 'destSmscMaxDigits' bit is
set in the cmlrRuleInputParameters object.rw CmlrMaximumDigits .1.3.6.1.4.1.9.9.396.1.6.1.39 |
cmlrRuleOrigSmeMinDigitsSpecifies the minimum number of digits that the global
title address specified by the cmlrRuleOrigSmeGta object
can contain for rule to match.
This object only applies when the 'origSmeMinDigits' bit is
set in the cmlrRuleInputParameters object.rw CmlrMinimumDigits .1.3.6.1.4.1.9.9.396.1.6.1.40 |
cmlrRuleOrigSmeMaxDigitsSpecifies the maximum number of digits that the global
title address specified by the cmlrRuleOrigSmeGta can
contain for rule to match.
This object only applies when the 'origSmeMaxDigits' bit is
set in the cmlrRuleInputParameters object.rw CmlrMaximumDigits .1.3.6.1.4.1.9.9.396.1.6.1.41 |
cmlrRuleOrigSmeTableNaiThe nature of specified address for the global tile
address specified within the message signal unit. This
object only applies when the 'origSmeTableNai' bit is
set in the cmlrRuleInputParameters object.rw CItpTcNAI (CISCO-ITP-TC-MIB) .1.3.6.1.4.1.9.9.396.1.6.1.42 |
cmlrRuleOrigSmeTableNpThe numbering plan for the destination short message
service center global title address specified within the
message signal unit.
This object only applies when the 'origSmeTableNp' bit is
set in the cmlrRuleInputParameters object.rw CItpTcNumberingPlan (CISCO-ITP-TC-MIB) .1.3.6.1.4.1.9.9.396.1.6.1.43 |
cmlrRuleOrigImsiGtaThe origination short message entity global title address.
When the length of the global title address is zero it
specified a wildcard match and all global title will
match GTA clause of rule.
This object only applies when the 'origImsiGta' bit is
set in the cmlrRuleInputParameters object.rw CItpTcGtaLongDisplay (CISCO-ITP-TC-MIB) .1.3.6.1.4.1.9.9.396.1.6.1.44 |
cmlrRuleOrigImsiNaiThe nature of specified address for the origination short
message entity global title address specified within the
message signal unit.
This object only applies when the 'origImsiNai' bit is
set in the cmlrRuleInputParameters object.rw CItpTcNAI (CISCO-ITP-TC-MIB) .1.3.6.1.4.1.9.9.396.1.6.1.45 |
cmlrRuleOrigImsiNpThe numbering plan for the origination short message
entity global title address specified within the message
signal unit.
This object only applies when the 'origImsiNp' bit is
set in the cmlrRuleInputParameters object.rw CItpTcNumberingPlan (CISCO-ITP-TC-MIB) .1.3.6.1.4.1.9.9.396.1.6.1.46 |
cmlrRuleOrigImsiMinDigitsSpecifies the minimum number of digits that the global
title address specified by the cmlrRuleOrigImsiGta object
can contain for rule to match.
This object only applies when the 'origImsiMinDigits' bit is
set in the cmlrRuleInputParameters object.rw CmlrMinimumDigits .1.3.6.1.4.1.9.9.396.1.6.1.47 |
cmlrRuleOrigImsiMaxDigitsSpecifies the maximum number of digits that the global
title address specified by the cmlrRuleOrigImsiGta object
can contain for rule to match.
This object only applies when the 'origImsiMaxDigits' bit is
set in the cmlrRuleInputParameters object.rw CmlrMaximumDigits .1.3.6.1.4.1.9.9.396.1.6.1.48 |
cmlrRuleOrigImsiTableThe name of the entry in the cmlrAddressTable that will be
searched for matches. The table will be search for the
following types of addresses based on values set in the
cmlrRuleInputParameters object.
This object only applies when the 'origImsiTable' bit is
set in the cmlrRuleInputParameters object.rw CmlrName .1.3.6.1.4.1.9.9.396.1.6.1.49 |
cmlrRuleOrigSmscMinDigitsSpecifies the minimum number of digits that the global
title address specified by the cmlrRuleOrigSmscGta
object can contain for rule to match.
This object only applies when the 'origSmscMinDigits'
bit is set in the cmlrRuleInputParameters object.rw CmlrMinimumDigits .1.3.6.1.4.1.9.9.396.1.6.1.50 |
cmlrRuleOrigSmscMaxDigitsSpecifies the maximum number of digits that the global
title address specified by the cmlrRuleOrigSmscGta object
can contain for rule to match.
This object only applies when the 'origSmscMaxDigits' bit is
set in the cmlrRuleInputParameters object.rw CmlrMaximumDigits .1.3.6.1.4.1.9.9.396.1.6.1.51 |
cmlrResultSetTableA table used to identify a group of results and define
parameter that apply to all result within the group.
Entries are added to this table via cmlrResultSetRowStatus
object in accordance with the RowStatus convention. SEQUENCE OF CmlrResultSetTableEntry .1.3.6.1.4.1.9.9.396.1.8 |
cmlrResultSetTableEntryThis table is used to define a collection of results. CmlrResultSetTableEntry .1.3.6.1.4.1.9.9.396.1.8.1 |
cmlrResultSetNameA name used to define a result group. CmlrName .1.3.6.1.4.1.9.9.396.1.8.1.1 |
cmlrResultSetUnavailDiscardWhen all results in a group are unavailable this
object defines whether to discard packet or to return
packet to SCCP layer for normal processing.
'true' Packet will be discarded.
'false' Packet will be returned to SCCP layer for normal
processing.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.396.1.8.1.2 |
cmlrResultSetRowStatusThe object is used by a management station to create or
delete the row entry in cmlrResultSetTable following
the RowStatus textual convention.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.9.9.396.1.8.1.3 |
cmlrResultTableA table used to identify a group of destination resources
The result group lists the appropriate destination
resources, and the mechanism used to select a single
destination for a given packet. State information is
determined for each possible destination. Congested
resources will only be used if no available, non-congested
destinations exist. Only available destinations are
considered for routing.
Entries are added to this table via cmlrResultRowStatus
object in accordance with the RowStatus convention. SEQUENCE OF CmlrResultTableEntry .1.3.6.1.4.1.9.9.396.1.9 |
cmlrResultTableEntryThis table is used to define a collection of
multi-layer routing statements. CmlrResultTableEntry .1.3.6.1.4.1.9.9.396.1.9.1 |
cmlrResultNumberThis object specifies the index for a list of results
specified per result group. CmlrId .1.3.6.1.4.1.9.9.396.1.9.1.1 |
cmlrResultTypeResult type used to route MSU.rw CmlrResultType .1.3.6.1.4.1.9.9.396.1.9.1.2 |
cmlrResultNetworkThe network name is used to indicate the network in which
the result parameters exist.rw CItpTcNetworkName (CISCO-ITP-TC-MIB) .1.3.6.1.4.1.9.9.396.1.9.1.3 |
cmlrResultOctetSpecified the information used to route the MSU
based on cmlrResultType object.rw CmlrResultOctet .1.3.6.1.4.1.9.9.396.1.9.1.4 |
cmlrResultPcA destination point code that must exist in the MTP3
routing table, and its state is extracted from MTP3
for availability purposes. This object only has
applies when the cmlrResultType has the 'pc' value.
Otherwise, this object will return zero value.rw CItpTcPointCode (CISCO-ITP-TC-MIB) .1.3.6.1.4.1.9.9.396.1.9.1.5 |
cmlrResultSsnThe subsystem number to be inserted into MSU. This
object only has applies when the cmlrResultType has
the 'pcSsn' value.
Otherwise, this object will return zero value.rw CItpTcSubSystemNumber (CISCO-ITP-TC-MIB) .1.3.6.1.4.1.9.9.396.1.9.1.6 |
cmlrResultWeightThis object specifies the weight applied to the weighted
round robin distribution algorithm used for multi-layer
result group. An integer value in the range of 0 to 10.
A value of ten indicates the resource should be selected
ten times more than a resource assigned a weight of one.rw INTEGER .1.3.6.1.4.1.9.9.396.1.9.1.7 |
cmlrResultCountsNumber of times this entry was invoked.ro Counter32 .1.3.6.1.4.1.9.9.396.1.9.1.8 |
cmlrResultRowStatusThe object is used by a management station to create or
delete the row entry in cmlrResultsTable following
the RowStatus textual convention.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.9.9.396.1.9.1.9 |
ciscoMlrMIBConform OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.396.2 |
ciscoMlrMIBCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.396.2.1 |
ciscoMlrMIBGroups OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.396.2.2 |