Home/Catalog/CISCO-ITP-GSCCP-MIB

CISCO-ITP-GSCCP-MIB

AI MIB Summary

The CISCO-ITP-GSCCP-MIB monitors and manages Global Title Translation (GTT) operations, Mated Application (MAP) configurations, and SCCP message flows on Cisco IP Transfer Point (ITP) hardware to ensure SS7 signaling over IP (SIGTRAN) compliance. This module provides granular visibility into translation entries, point code routing, and error statistics for Signalling Connection Control Part (SCCP) traffic transported via M3UA or SUA protocols.

The MIB for signalling Connection Control Part(SCCP) messages transported over Signalling System No. 7 (SS7) Network via Cisco IP Transfer Point. This MIB provides information specified in ITU Q752 Monitoring and Measurements for Signalling System No. 7(SS7) Network. The Cisco IP Transfer Point (ITP) is a hardware and software solution that transports SS7 traffic using IP. Each ITP node provides function similar to SS7 Signalling point. The relevant ITU documents describing this technology is the ITU Q series, including ITU Q.700: Introduction to CCITT Signalling System No. 7 and ITU Q.701 Functional description of the message transfer part (MTP) of Signalling System No. 7. The IETF Working Group Signalling Transport (SIGTRAN) has defined MTP3 User Adaptation (M3UA) and SCCP User Adaptation (SUA) protocols. The drafts can be found at: http://www.ietf.org/html.charters/sigtran-charter.html This MIB consists of the following tables: Instance Table Concerned Point Code List Table Mated Application (MAP) Table Global Title Translation (GTT) Selector Table Global Title Address (GTA) Table Application Group Table Prefix Conversion Table Translation Entries Table Global Title Errors Table Abbreviations: CDPA - Called Party Address CGPA - Calling Party Address CLLI - Common Language Location Codes CR - Connection Request message CREF - Connection Refusal message DPC - Destination Point Code ERR - Error message GTA - Global Title Address GTI - Global Title Indicator GTT - Global Title Translation LUDT - long unitdata message LUDTS - long unitdata service message M2PA - MTP2 Peer-to-Peer Adaptation Layer M3UA - MTP3-User Adaptation MAP - Mated Application Table MSU - Message Signal Unit MTP - Message Transport Protocol MTP2 - Layer 2 of Message Transport Protocol MTP3 - Layer 3 of Message Transport Protocol NAI - Nature of Address Indicator NP - Numbering Plan OPC - Originating Point Code PC - Point Code RTN - Route Table Name RSR - Reset Request message SCCP - Signalling Connection Control Part SCTP - Stream Transmission Protocol(RFC 2960) SI - Signalling Indicator SP - Signalling Point SLC - Signalling Link Code SLS - Signalling Link Selector SSN - Subsystem Number SUA - SCCP-User Adaptation TFR - Transfer Restricted messages TT - Title Translation UDT - unitdata message UDTS - unitdata service message XUDT - extended unitdata message XUDTS - extended unitdata service message
Main OID:
ciscoGsccpMIB.1.3.6.1.4.1.9.9.335
250
Objects
Active
Status
7
Dependencies

Imported Objects

Objects

250 total
Object Name
ciscoGsccpMIB
MODULE-IDENTITY
.1.3.6.1.4.1.9.9.335
ciscoGsccpMIBNotifs
OBJECT IDENTIFIER
.1.3.6.1.4.1.9.9.335.0
ciscoGsccpGttMapStateChange
NOTIFICATION-TYPE
.1.3.6.1.4.1.9.9.335.0.1
ciscoGsccpGttLoadTable
NOTIFICATION-TYPE
.1.3.6.1.4.1.9.9.335.0.2
ciscoGsccpGttErrors
NOTIFICATION-TYPE
.1.3.6.1.4.1.9.9.335.0.3
ciscoGsccpSegReassUnsup
NOTIFICATION-TYPE
.1.3.6.1.4.1.9.9.335.0.4
ciscoGsccpSOGReceived
NOTIFICATION-TYPE
.1.3.6.1.4.1.9.9.335.0.5
ciscoGsccpRmtCongestion
NOTIFICATION-TYPE
.1.3.6.1.4.1.9.9.335.0.6
ciscoGsccpLocalSsStateChange
NOTIFICATION-TYPE
.1.3.6.1.4.1.9.9.335.0.7
ciscoGsccpMIBObjects
OBJECT IDENTIFIER
.1.3.6.1.4.1.9.9.335.1
cgsccpScalars
OBJECT IDENTIFIER
.1.3.6.1.4.1.9.9.335.1.1
cgsccpGttTranslateSamplerw
Unsigned32
.1.3.6.1.4.1.9.9.335.1.1.1
cgsccpGttTranslatePeriodrw
Unsigned32
.1.3.6.1.4.1.9.9.335.1.1.2
cgsccpGttMapStateNotifEnabledrw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.9.9.335.1.1.3
cgsccpGttLoadTableNotifEnabledrw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.9.9.335.1.1.4
cgsccpGttTransErrorsNotifEnabledrw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.9.9.335.1.1.5
cgsccpGttErrorPeriodrw
Unsigned32
.1.3.6.1.4.1.9.9.335.1.1.6
cgsccpGttErrorRecoveryCountrw
Unsigned32
.1.3.6.1.4.1.9.9.335.1.1.7
cgsccpInst
OBJECT IDENTIFIER
.1.3.6.1.4.1.9.9.335.1.2
cgsccpInstTable
SEQUENCE OF CgsccpInstTableEntry
.1.3.6.1.4.1.9.9.335.1.2.1
cgsccpInstTableEntry
CgsccpInstTableEntry
.1.3.6.1.4.1.9.9.335.1.2.1.1
cgsccpInstTotalMsgsro
Counter32 UNITS "packets"
.1.3.6.1.4.1.9.9.335.1.2.1.1.1
cgsccpInstLocalMsgsro
Counter32 UNITS "packets"
.1.3.6.1.4.1.9.9.335.1.2.1.1.2
cgsccpInstTotalGttMsgsro
Counter32 UNITS "packets"
.1.3.6.1.4.1.9.9.335.1.2.1.1.3
cgsccpInstUDTMsgsSentro
Counter32 UNITS "packets"
.1.3.6.1.4.1.9.9.335.1.2.1.1.4
cgsccpInstUDTSMsgsSentro
Counter32 UNITS "packets"
.1.3.6.1.4.1.9.9.335.1.2.1.1.5
cgsccpInstUDTSMsgsAttemptedro
Counter32 UNITS "packets"
.1.3.6.1.4.1.9.9.335.1.2.1.1.6
cgsccpInstUDTMsgsRcvdro
Counter32 UNITS "packets"
.1.3.6.1.4.1.9.9.335.1.2.1.1.7
cgsccpInstUDTSMsgsRcvdro
Counter32 UNITS "packets"
.1.3.6.1.4.1.9.9.335.1.2.1.1.8
cgsccpInstXUDTMsgsSentro
Counter32 UNITS "packets"
.1.3.6.1.4.1.9.9.335.1.2.1.1.9
cgsccpInstXUDTSMsgsAttemptedro
Counter32 UNITS "packets"
.1.3.6.1.4.1.9.9.335.1.2.1.1.10
cgsccpInstXUDTSMsgsSentro
Counter32 UNITS "packets"
.1.3.6.1.4.1.9.9.335.1.2.1.1.11
cgsccpInstXUDTMsgsRcvdro
Counter32 UNITS "packets"
.1.3.6.1.4.1.9.9.335.1.2.1.1.12
cgsccpInstXUDTSMsgsRcvdro
Counter32 UNITS "packets"
.1.3.6.1.4.1.9.9.335.1.2.1.1.13
cgsccpInstLUDTMsgsSentro
Counter32 UNITS "packets"
.1.3.6.1.4.1.9.9.335.1.2.1.1.14
cgsccpInstLUDTSMsgsSentro
Counter32 UNITS "packets"
.1.3.6.1.4.1.9.9.335.1.2.1.1.15
cgsccpInstLUDTMsgsRcvdro
Counter32 UNITS "packets"
.1.3.6.1.4.1.9.9.335.1.2.1.1.16
cgsccpInstLUDTSMsgsRcvdro
Counter32 UNITS "packets"
.1.3.6.1.4.1.9.9.335.1.2.1.1.17
cgsccpInstCrToMtpro
Counter32 UNITS "packets"
.1.3.6.1.4.1.9.9.335.1.2.1.1.18
cgsccpInstCrefToMtpro
Counter32 UNITS "packets"
.1.3.6.1.4.1.9.9.335.1.2.1.1.19
cgsccpInstCrFromMtpro
Counter32 UNITS "packets"
.1.3.6.1.4.1.9.9.335.1.2.1.1.20
cgsccpInstCrefFromMtpro
Counter32 UNITS "packets"
.1.3.6.1.4.1.9.9.335.1.2.1.1.21
cgsccpInstRsrToMtpro
Counter32 UNITS "packets"
.1.3.6.1.4.1.9.9.335.1.2.1.1.22
cgsccpInstRsrFromMtpro
Counter32 UNITS "packets"
.1.3.6.1.4.1.9.9.335.1.2.1.1.23
cgsccpInstErrToMtpro
Counter32 UNITS "packets"
.1.3.6.1.4.1.9.9.335.1.2.1.1.24
cgsccpInstErrFromMtpro
Counter32 UNITS "packets"
.1.3.6.1.4.1.9.9.335.1.2.1.1.25
cgsccpInstQ752T7E1ro
Counter32 UNITS "packets"
.1.3.6.1.4.1.9.9.335.1.2.1.1.26
cgsccpInstInvalidGttFormatro
Counter32 UNITS "packets"
.1.3.6.1.4.1.9.9.335.1.2.1.1.27
cgsccpInstQ752T7E13ro
Counter32 UNITS "packets"
.1.3.6.1.4.1.9.9.335.1.2.1.1.28
cgsccpInstMapNotFoundro
Counter32 UNITS "packets"
.1.3.6.1.4.1.9.9.335.1.2.1.1.29
cgsccpInstQ752T7E7ro
Counter32 UNITS "packets"
.1.3.6.1.4.1.9.9.335.1.2.1.1.30
cgsccpInstGttConfigStatusro
CItpTcTableLoadStatus (CISCO-ITP-TC-MIB)
.1.3.6.1.4.1.9.9.335.1.2.1.1.31
cgsccpInstConfigTSro
TimeStamp (SNMPv2-TC)
.1.3.6.1.4.1.9.9.335.1.2.1.1.32
cgsccpInstGttConfigTSro
TimeStamp (SNMPv2-TC)
.1.3.6.1.4.1.9.9.335.1.2.1.1.33
cgsccpInstLastURLro
CItpTcURL (CISCO-ITP-TC-MIB)
.1.3.6.1.4.1.9.9.335.1.2.1.1.34
cgsccpInstConPcTableEntriesro
Gauge32 UNITS "entries"
.1.3.6.1.4.1.9.9.335.1.2.1.1.35
cgsccpInstMapTableEntriesro
Gauge32 UNITS "entries"
.1.3.6.1.4.1.9.9.335.1.2.1.1.36
cgsccpInstGtaTableEntriesro
Gauge32 UNITS "entries"
.1.3.6.1.4.1.9.9.335.1.2.1.1.37
cgsccpInstSelTableEntriesro
Gauge32 UNITS "entries"
.1.3.6.1.4.1.9.9.335.1.2.1.1.38
cgsccpInstAppGrTableEntriesro
Gauge32 UNITS "entries"
.1.3.6.1.4.1.9.9.335.1.2.1.1.39
cgsccpInstRowStatusrw
RowStatus (SNMPv2-TC)
.1.3.6.1.4.1.9.9.335.1.2.1.1.40
cgsccpInstPrefTableEntriesro
Gauge32 UNITS "entries"
.1.3.6.1.4.1.9.9.335.1.2.1.1.41
cgsccpInstQ752Unqualifiedro
Counter32 UNITS "packets"
.1.3.6.1.4.1.9.9.335.1.2.1.1.42
cgsccpInstErrorIndicatorro
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.9.9.335.1.2.1.1.43
cgsccpInstReassUnsupro
Counter32
.1.3.6.1.4.1.9.9.335.1.2.1.1.44
cgsccpInstReassFailro
Counter32
.1.3.6.1.4.1.9.9.335.1.2.1.1.45
cgsccpInstSegUnsupro
Counter32
.1.3.6.1.4.1.9.9.335.1.2.1.1.46
cgsccpInstSegFailro
Counter32
.1.3.6.1.4.1.9.9.335.1.2.1.1.47
cgsccpGttConPc
OBJECT IDENTIFIER
.1.3.6.1.4.1.9.9.335.1.3
cgsccpGttConPcTable
SEQUENCE OF CgsccpGttConPcTableEntry
.1.3.6.1.4.1.9.9.335.1.3.1
cgsccpGttConPcTableEntry
CgsccpGttConPcTableEntry
.1.3.6.1.4.1.9.9.335.1.3.1.1
cgsccpGttConPcListName
CgsccpConPcListName
.1.3.6.1.4.1.9.9.335.1.3.1.1.1
cgsccpGttConPointCode
CItpTcPointCode (CISCO-ITP-TC-MIB)
.1.3.6.1.4.1.9.9.335.1.3.1.1.2
cgsccpGttConPcRowStatusrw
RowStatus (SNMPv2-TC)
.1.3.6.1.4.1.9.9.335.1.3.1.1.3
cgsccpGttMap
OBJECT IDENTIFIER
.1.3.6.1.4.1.9.9.335.1.4
cgsccpGttMapTable
SEQUENCE OF CgsccpGttMapTableEntry
.1.3.6.1.4.1.9.9.335.1.4.1
cgsccpGttMapTableEntry
CgsccpGttMapTableEntry
.1.3.6.1.4.1.9.9.335.1.4.1.1
cgsccpGttMapPc
CItpTcPointCode (CISCO-ITP-TC-MIB)
.1.3.6.1.4.1.9.9.335.1.4.1.1.1
cgsccpGttMapSsn
CItpTcSubSystemNumber (CISCO-ITP-TC-MIB)
.1.3.6.1.4.1.9.9.335.1.4.1.1.2
cgsccpGttMapDisplayPCro
CItpTcDisplayPC (CISCO-ITP-TC-MIB)
.1.3.6.1.4.1.9.9.335.1.4.1.1.3
cgsccpGttMapDisplaySSro
CgsccpGttDisplaySS
.1.3.6.1.4.1.9.9.335.1.4.1.1.4
cgsccpGttMapTyperw
CgsccpGttMapType
.1.3.6.1.4.1.9.9.335.1.4.1.1.5
cgsccpGttMapPcStatusro
CgsccpGttMapPcStatus
.1.3.6.1.4.1.9.9.335.1.4.1.1.6
cgsccpGttMapSsStatusro
CgsccpGttMapSsStatus
.1.3.6.1.4.1.9.9.335.1.4.1.1.7
cgsccpGttMapMultIndrw
CgsccpGttMultInd
.1.3.6.1.4.1.9.9.335.1.4.1.1.8
cgsccpGttMapBackupPcrw
CItpTcPointCode (CISCO-ITP-TC-MIB)
.1.3.6.1.4.1.9.9.335.1.4.1.1.9
cgsccpGttMapBackupSsnrw
CItpTcSubSystemNumber (CISCO-ITP-TC-MIB)
.1.3.6.1.4.1.9.9.335.1.4.1.1.10
cgsccpGttMapConPcListrw
CgsccpConPcListName
.1.3.6.1.4.1.9.9.335.1.4.1.1.11
cgsccpGttMapReRouteOnCongrw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.9.9.335.1.4.1.1.12
cgsccpGttMapAdjacentrw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.9.9.335.1.4.1.1.13
cgsccpGttMapLastSsUsedro
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.9.9.335.1.4.1.1.14
cgsccpGttMapUsedro
Counter32 UNITS "messages"
.1.3.6.1.4.1.9.9.335.1.4.1.1.15
cgsccpGttMapAltUsedro
Counter32 UNITS "messages"
.1.3.6.1.4.1.9.9.335.1.4.1.1.16
cgsccpGttMapSccpUnavailro
Counter32 UNITS "occurrences"
.1.3.6.1.4.1.9.9.335.1.4.1.1.17
cgsccpGttMapQ752T7E3Failro
Counter32 UNITS "occurrences"
.1.3.6.1.4.1.9.9.335.1.4.1.1.18
cgsccpGttMapQ752T7E3Unro
Counter32 UNITS "occurrences"
.1.3.6.1.4.1.9.9.335.1.4.1.1.19
cgsccpGttMapQ752T7E4ro
Counter32 UNITS "occurrences"
.1.3.6.1.4.1.9.9.335.1.4.1.1.20
cgsccpGttMapQ752T7E5ro
Counter32 UNITS "occurrences"
.1.3.6.1.4.1.9.9.335.1.4.1.1.21
cgsccpGttMapQ752T7E6ro
Counter32 UNITS "occurrences"
.1.3.6.1.4.1.9.9.335.1.4.1.1.22
cgsccpGttMapRefCountro
Gauge32
.1.3.6.1.4.1.9.9.335.1.4.1.1.23
Showing 100 of 250 OID objects

CISCO-ITP-GSCCP-MIB Technical Reference Overview

The CISCO-ITP-GSCCP-MIB SNMP MIB module published by Cisco defines 250 managed OID objects, including 196 scalar/column metrics, 13 SNMP tables, and 7 trap/notification events anchored at base OID .1.3.6.1.4.1.9.9.335. Key tabular structures include cgsccpInstTable, cgsccpGttConPcTable, cgsccpGttAppGrTable, cgsccpGttMapTable, cgsccpGttSelTable, cgsccpGttGtaTable. Monitored SNMP traps/notifications include ciscoGsccpGttMapStateChange, ciscoGsccpGttLoadTable, ciscoGsccpGttErrors, ciscoGsccpSegReassUnsup, ciscoGsccpSOGReceived, ciscoGsccpRmtCongestion.

Key OID Definitions in CISCO-ITP-GSCCP-MIB

ciscoGsccpMIBMODULE-IDENTITYnot-accessible
.1.3.6.1.4.1.9.9.335

The MIB for signalling Connection Control Part(SCCP) messages transported over Signalling System No. 7 (SS7) Network via Cisco IP Transfer Point. This MIB provides information specified in ITU Q752 Monitoring and Measurements for Signalling System No. 7(SS7) Network. The Cisco IP Transfer Point (ITP) is a hardware and software solution that transports SS7 traffic using IP. Each ITP node provides function similar to SS7 Signalling point. The relevant ITU documents describing this technology is the ITU Q series, including ITU Q.700: Introduction to CCITT Signalling System No. 7 and ITU Q.701 Functional description of the message transfer part (MTP) of Signalling System No. 7. The IETF Working Group Signalling Transport (SIGTRAN) has defined MTP3 User Adaptation (M3UA) and SCCP User Adaptation (SUA) protocols. The drafts can be found at: http://www.ietf.org/html.charters/sigtran-charter.html This MIB consists of the following tables: Instance Table Concerned Point Code List Table Mated Application (MAP) Table Global Title Translation (GTT) Selector Table Global Title Address (GTA) Table Application Group Table Prefix Conversion Table Translation Entries Table Global Title Errors Table Abbreviations: CDPA - Called Party Address CGPA - Calling Party Address CLLI - Common Language Location Codes CR - Connection Request message CREF - Connection Refusal message DPC - Destination Point Code ERR - Error message GTA - Global Title Address GTI - Global Title Indicator GTT - Global Title Translation LUDT - long unitdata message LUDTS - long unitdata service message M2PA - MTP2 Peer-to-Peer Adaptation Layer M3UA - MTP3-User Adaptation MAP - Mated Application Table MSU - Message Signal Unit MTP - Message Transport Protocol MTP2 - Layer 2 of Message Transport Protocol MTP3 - Layer 3 of Message Transport Protocol NAI - Nature of Address Indicator NP - Numbering Plan OPC - Originating Point Code PC - Point Code RTN - Route Table Name RSR - Reset Request message SCCP - Signalling Connection Control Part SCTP - Stream Transmission Protocol(RFC 2960) SI - Signalling Indicator SP - Signalling Point SLC - Signalling Link Code SLS - Signalling Link Selector SSN - Subsystem Number SUA - SCCP-User Adaptation TFR - Transfer Restricted messages TT - Title Translation UDT - unitdata message UDTS - unitdata service message XUDT - extended unitdata message XUDTS - extended unitdata service message

cgsccpInstTableSEQUENCEnot-accessible
.1.3.6.1.4.1.9.9.335.1.2.1

SCCP information per instance of signalling point.

cgsccpGttConPcTableSEQUENCEnot-accessible
.1.3.6.1.4.1.9.9.335.1.3.1

A table of concerned point codes.

cgsccpGttAppGrTableSEQUENCEnot-accessible
.1.3.6.1.4.1.9.9.335.1.7.1

A table of SCCP GTT Application Group Table entries.

cgsccpGttMapTableSEQUENCEnot-accessible
.1.3.6.1.4.1.9.9.335.1.4.1

A table of SCCP GTT Mated Application (MAP) entries.

cgsccpGttSelTableSEQUENCEnot-accessible
.1.3.6.1.4.1.9.9.335.1.5.1

A table of SCCP GTT Selector entries.

cgsccpGttGtaTableSEQUENCEnot-accessible
.1.3.6.1.4.1.9.9.335.1.6.1

A table of SCCP Global Title Address entries.

cgsccpGttPrefTableSEQUENCEnot-accessible
.1.3.6.1.4.1.9.9.335.1.8.1

A table of SCCP GTT Prefix Conversion Table entries. When a packet with GTA is received, it may need global title translation depending on Translation Type (TT), Numbering Plan (NP), Network Address Indicator (NAI) and Global Title Indicator (GTI) present in the packet. To perform the translation a selector (cgsccpGttSelTable) corresponding to TT, NP, NAI and GTI is used. The selector also specifies prefix conversion of the GTA before (pre) performing the global title translation or after (post) performing the global title translation. A selector can specify any or both (pre and post) prefix conversion tables. The prefix conversion involves matching of GTA digits in the cgsccpGttPrefInAddr and then replacing those digits with the digits in cgsccpGttPrefOutAddr.

cgsccpGttTranslateTableSEQUENCEnot-accessible
.1.3.6.1.4.1.9.9.335.1.9.1

The translate table contains a history of the number of global title packets that were translated on the various processors enabled for this function. The ability to translate GTT is critical to many SS7 functions. This table provides peak utilization to allow planning of maximum load on SS7 network.

cgsccpGttPref2TableSEQUENCEnot-accessible
.1.3.6.1.4.1.9.9.335.1.10.1

A table of SCCP GTT Prefix Conversion Table entries. This table replaces the cgsccpGttPrefTable tables and allow prefix conversion to be specified per instance. When a packet with GTA is received, it may need global title translation depending on Translation Type (TT), Numbering Plan (NP), Network Address Indicator (NAI) and Global Title Indicator (GTI) present in the packet. To perform the translation a selector (cgsccpGttSelTable) corresponding to TT, NP, NAI and GTI is used. The selector also specifies prefix conversion of the GTA before (pre) performing the global title translation or after (post) performing the global title translation. A selector can specify any or both (pre and post) prefix conversion tables. The prefix conversion involves matching of GTA digits in the cgsccpGttPref2InAddr and then replacing those digits with the digits in cgsccpGttPref2OutAddr.

cgsccpGttAppGr2TableSEQUENCEnot-accessible
.1.3.6.1.4.1.9.9.335.1.11.1

A table of SCCP GTT Application Group Table entries.

cgsccpGttErrorsTableSEQUENCEnot-accessible
.1.3.6.1.4.1.9.9.335.1.12.1

This table is used to indicate errors in global title translation and will be used to provide information for ciscoGsccpGttErrors notification.

cgsccpSSNTableSEQUENCEnot-accessible
.1.3.6.1.4.1.9.9.335.1.13.1

The SSN table provides a breakdown of SCCP measurements at local subsystem level.

cgsccpSSNClassTableSEQUENCEnot-accessible
.1.3.6.1.4.1.9.9.335.1.14.1

The SSN Class table contains information about the number of UDT, XUDT, LUDT messages originated and terminated for a specific SSN and class. This provides the granularity of information required by Q752 elements 9.6 and 9.7

ciscoGsccpGttMapStateChangeNOTIFICATION-TYPEnot-accessible
.1.3.6.1.4.1.9.9.335.0.1

The notification generated when a mated application subsystem changes to a new state. The value of cgsccpGttMapSsStatus indicates the new state for the subsystem.

ciscoGsccpGttLoadTableNOTIFICATION-TYPEnot-accessible
.1.3.6.1.4.1.9.9.335.0.2

This notification is generated whenever a load operation is started or completes.

ciscoGsccpGttErrorsNOTIFICATION-TYPEnot-accessible
.1.3.6.1.4.1.9.9.335.0.3

This notification is generated whenever any global title error is encountered in last interval specified by the cgsccpGttErrorPeriod and the cgsccpInstErrorIndicator will be set to true. The notification will also be generated when errors have abated. The notification is generated after the number of recovery intervals as specified by the cgsccpGttErrorRecoveryCount object has passed without any global title errors.

ciscoGsccpSegReassUnsupNOTIFICATION-TYPEnot-accessible
.1.3.6.1.4.1.9.9.335.0.4

This notification is generated initially when a SCCP message is dropped due to a segmentation or reassembly unsupported or failure errors in last interval specified by the cgsccpGttErrorPeriod and the cgsccpInstErrorIndicator will be set to true. The notification will also be generated after the number of recovery intervals as specified by the cgsccpGttErrorRecoveryCount object has passed without any segmentation or reassembly unsupported errors.

ciscoGsccpSOGReceivedNOTIFICATION-TYPEnot-accessible
.1.3.6.1.4.1.9.9.335.0.5

This notification is generated initially when a Subsystem Out-of-Service Grant is sent in response to a Subsystem Out-of-Service Request message. The affected PC and affected SSN are provided with this notification.

ciscoGsccpRmtCongestionNOTIFICATION-TYPEnot-accessible
.1.3.6.1.4.1.9.9.335.0.6

This notification is generated initially when congestion is experienced in the remote SCCP component for the first time in last interval specified by the cgsccpGttErrorPeriod. The notification is generated after the number of recovery intervals as specified by the cgsccpGttErrorRecoveryCount object has passed without any congestion errors and total number of local congestion observed for different congestion levels at the end of the interval along with the latest known congestion status for that remote signalling point will be provided.

ciscoGsccpLocalSsStateChangeNOTIFICATION-TYPEnot-accessible
.1.3.6.1.4.1.9.9.335.0.7

The notification generated when a local application subsystem changes to a new state. The subsystem number and the latest subsystem state will be provided in this notification.

cgsccpGttTranslateSampleUnsigned32read-write
.1.3.6.1.4.1.9.9.335.1.1.1

The length of the sample interval used to collect number of maximum Global Title Translations per second.

cgsccpGttTranslatePeriodUnsigned32read-write
.1.3.6.1.4.1.9.9.335.1.1.2

The length of the period used to collect the maximum Global Title Translations rate. Samples are calculated for the time period specified by the cgsccpGttTranslateSample object.

cgsccpGttMapStateNotifEnabledTruthValueread-write
.1.3.6.1.4.1.9.9.335.1.1.3

The Map state notification truth value. 'true' Indicates that the ciscoGsccpGttMapStateChange notification is to be generated when the state changes. That is, the notification generation is enabled. 'false' Indicates that the ciscoGsccpGttMapStateChange notification generation is disabled.

More MIBs from Cisco

Browse all CiscoMIBs →
CISCO-UNIFIED-COMPUTING-COMPUTE-MIB

The CISCO-UNIFIED-COMPUTING-COMPUTE-MIB provides SNMP-based monitoring and management of Cisco UCS compute blades, servers, and chassis components, exposing critical metrics such as CPU utilization, memory usage, thermal sensor readings, power supply status, and interface operational states. This module enables granular visibility into the health and performance of the Cisco Unified Computing System's compute subsystems for capacity planning and fault isolation.

1401 objects→
CISCO-UNIFIED-COMPUTING-STORAGE-MIB

The CISCO-UNIFIED-COMPUTING-STORAGE-MIB facilitates SNMP-based monitoring and management of storage subsystems, including Fibre Channel and iSCSI interfaces, within the Cisco Unified Computing System (UCS) fabric interconnects and blade servers. It exposes critical operational metrics such as port status, error counters, throughput statistics, and storage controller health states to enable granular visibility into the storage infrastructure.

1295 objects→
CISCO-UNIFIED-COMPUTING-VNIC-MIB

The CISCO-UNIFIED-COMPUTING-VNIC-MIB enables SNMP-based monitoring and management of Virtual Network Interface Card (vNIC) attributes, including operational status, traffic counters, and binding configurations, within the Cisco Unified Computing System (UCS) fabric interconnects and server blades.

1161 objects→
CERENT-GENERIC-MIB

SNMP MIB module

984 objects→
CISCO-UNIFIED-COMPUTING-BIOS-MIB

The CISCO-UNIFIED-COMPUTING-BIOS-MIB enables SNMP-based monitoring and configuration of BIOS-level parameters, firmware versions, and hardware initialization states within Cisco Unified Computing System (UCS) servers. It provides visibility into critical server boot diagnostics, BIOS settings, and hardware readiness indicators to facilitate low-level infrastructure management and troubleshooting.

937 objects→
CISCO-UNIFIED-COMPUTING-ETHER-MIB

The CISCO-UNIFIED-COMPUTING-ETHER-MIB provides SNMP management interfaces for monitoring Ethernet interface statistics, link states, and error counters on Cisco Unified Computing System (UCS) fabric interconnects and blade server line cards. This module enables the tracking of physical layer connectivity, port throughput, and packet error rates within the UCS Ethernet switching infrastructure.

920 objects→