Home/Catalog/CISCO-ITP-GSP-MIB

CISCO-ITP-GSP-MIB

AI MIB Summary

The CISCO-ITP-GSP-MIB monitors and manages Cisco IP Transfer Point (ITP) hardware and software instances acting as Gateway Signalling Points (GSP) to transport SS7 traffic over IP networks. It tracks critical SS7 MTP layer metrics including link status, activity control, error rates (AERM/SUERM), point code routing, and signaling link states (activation, deactivation, restoration) for multiple GSP instances within a single configuration.

The MIB for managing Signalling Points and its associated messages transported over Signalling System No. 7 (SS7) Network via Cisco IP Transfer Point. This MIB replaces the CISCO-ITP-SP-MIB and provide support multiple instances of a signalling point within same configuration. The Cisco IP Transfer Point (ITP) is a hardware and software solution that transports SS7 traffic using IP. Each ITP node provides function similar to SS7 Signalling point. The relevant ITU documents describing this technology is the ITU Q series, including ITU Q.700: Introduction to CCITT Signalling System No. 7 and ITU Q.701 Functional description of the message transfer part (MTP) of Signalling System No. 7. This MIB models the GSP as follows: Abbreviations: AERM - Alignment Error Rate Monitor CLLI - Common-Language Location Identification DPC - Destination Point Code GSP - Gateway Signalling Point HSL - High Speed Link (ATM based) LLSC - link set control LSAC - Signalling link activity control LSDA - Signalling data link allocation LSLA - Signalling link activation LSLD - Signalling link deactivation LSLR - Signalling link restoration LSSU - Link Status Signal Unit LSTA - Signalling terminal allocation MTP - Message Transport Protocol MTP2 - Layer 2 of Message Transport Protocol MTP3 - Layer 3 of Message Transport Protocol NTT - The Japanese Nippon Telephone & Telegraph OPC - Originating Point Code PC - Point Code RTN - RouteTableName SCTP - Stream Transmission Protocol(RFC 2960) SIB - Status Indicator Busy SLT - Signalling Link Test SLTA - Signalling Link Test Acknowledgement SP - Signalling Point SS7 - System No. 7 (SS7) Network SUERM - Signal Unit Error Rate Monitor TCBC - Changeback control TCOC - Changeover control TCRC - Controlled rerouting control TFRC - Forced rerouting control TLAC - Link availability control TPRC - Signalling point restart control TRCC - Signalling route set congestion control TSFC - Signalling traffic flow control TSRC - Signalling routing control TTC - The Japanese Telecommunications Technology Committee WRR - Weighted round robin
Main OID:
ciscoGspMIB.1.3.6.1.4.1.9.9.336
228
Objects
Active
Status
8
Dependencies

Imported Objects

Objects

228 total
Object Name
ciscoGspMIB
MODULE-IDENTITY
.1.3.6.1.4.1.9.9.336
ciscoGspMIBNotifs
OBJECT IDENTIFIER
.1.3.6.1.4.1.9.9.336.0
ciscoGspLinksetStateChange
NOTIFICATION-TYPE
.1.3.6.1.4.1.9.9.336.0.1
ciscoGspLinkStateChange
NOTIFICATION-TYPE
.1.3.6.1.4.1.9.9.336.0.2
ciscoGspCongestionChange
NOTIFICATION-TYPE
.1.3.6.1.4.1.9.9.336.0.3
ciscoGspLinkRcvdUtilChange
NOTIFICATION-TYPE
.1.3.6.1.4.1.9.9.336.0.4
ciscoGspLinkSentUtilChange
NOTIFICATION-TYPE
.1.3.6.1.4.1.9.9.336.0.5
ciscoGspIsolation
NOTIFICATION-TYPE
.1.3.6.1.4.1.9.9.336.0.6
ciscoGspUPUReceived
NOTIFICATION-TYPE
.1.3.6.1.4.1.9.9.336.0.8
ciscoGspUPUTransmitted
NOTIFICATION-TYPE
.1.3.6.1.4.1.9.9.336.0.9
ciscoGspRxCongestionChange
NOTIFICATION-TYPE
.1.3.6.1.4.1.9.9.336.0.10
ciscoGspMIBObjects
OBJECT IDENTIFIER
.1.3.6.1.4.1.9.9.336.1
cgspScalars
OBJECT IDENTIFIER
.1.3.6.1.4.1.9.9.336.1.1
cgspCLLICoderw
CItpTcCLLI (CISCO-ITP-TC-MIB)
.1.3.6.1.4.1.9.9.336.1.1.1
cgspUtilSampleIntervalrw
CgspSampleInterval UNITS "seconds"
.1.3.6.1.4.1.9.9.336.1.1.2
cgspUtilThresholdrw
CgspPercentThreshold UNITS "percent"
.1.3.6.1.4.1.9.9.336.1.1.3
cgspUtilAbateDeltarw
CgspPercentThreshold UNITS "percent"
.1.3.6.1.4.1.9.9.336.1.1.4
cgspPlanCapacityDefaultrw
CgspLinkCapacity UNITS "bits per second"
.1.3.6.1.4.1.9.9.336.1.1.5
cgspEventSequenceNumberro
Counter32 UNITS "events"
.1.3.6.1.4.1.9.9.336.1.1.6
cgspUPUNotifWindowTimerw
Integer32
.1.3.6.1.4.1.9.9.336.1.1.7
cgspProfile
OBJECT IDENTIFIER
.1.3.6.1.4.1.9.9.336.1.2
cgspProfileTable
SEQUENCE OF CgspProfileTableEntry
.1.3.6.1.4.1.9.9.336.1.2.1
cgspProfileTableEntry
CgspProfileTableEntry
.1.3.6.1.4.1.9.9.336.1.2.1.1
cgspProfileName
CgspProfileName
.1.3.6.1.4.1.9.9.336.1.2.1.1.1
cgspProfileVariantrw
CgspSS7Variant
.1.3.6.1.4.1.9.9.336.1.2.1.1.2
cgspProfileMtp2BundleTimerrw
Integer32 (0..0 | 5..10000)
.1.3.6.1.4.1.9.9.336.1.2.1.1.3
cgspProfileMtp2SendQueueDepthrw
Integer32
.1.3.6.1.4.1.9.9.336.1.2.1.1.4
cgspProfileRowStatusrw
RowStatus (SNMPv2-TC)
.1.3.6.1.4.1.9.9.336.1.2.1.1.5
cgspProfileTimerTable
SEQUENCE OF CgspProfileTimerTableEntry
.1.3.6.1.4.1.9.9.336.1.2.2
cgspProfileTimerTableEntry
CgspProfileTimerTableEntry
.1.3.6.1.4.1.9.9.336.1.2.2.1
cgspProfileTimerNumber
CgspTimerNumbers
.1.3.6.1.4.1.9.9.336.1.2.2.1.1
cgspProfileTimerValuerw
CgspTimerValue UNITS "milliseconds"
.1.3.6.1.4.1.9.9.336.1.2.2.1.2
cgspProfileTimerRowStatusrw
RowStatus (SNMPv2-TC)
.1.3.6.1.4.1.9.9.336.1.2.2.1.3
cgspInstance
OBJECT IDENTIFIER
.1.3.6.1.4.1.9.9.336.1.3
cgspInstanceTable
SEQUENCE OF CgspInstanceTableEntry
.1.3.6.1.4.1.9.9.336.1.3.1
cgspInstanceTableEntry
CgspInstanceTableEntry
.1.3.6.1.4.1.9.9.336.1.3.1.1
cgspInstNetwork
CItpTcNetworkName (CISCO-ITP-TC-MIB)
.1.3.6.1.4.1.9.9.336.1.3.1.1.1
cgspInstNetworkIndicatorrw
CItpTcNetworkIndicator (CISCO-ITP-TC-MIB)
.1.3.6.1.4.1.9.9.336.1.3.1.1.2
cgspInstVariantrw
CgspSS7Variant
.1.3.6.1.4.1.9.9.336.1.3.1.1.3
cgspInstDisplayNamerw
SnmpAdminString
.1.3.6.1.4.1.9.9.336.1.3.1.1.4
cgspInstDescriptionrw
SnmpAdminString
.1.3.6.1.4.1.9.9.336.1.3.1.1.5
cgspInstTFRrw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.9.9.336.1.3.1.1.6
cgspInstCongestionsLevelsrw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.9.9.336.1.3.1.1.7
cgspInstFastRestartrw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.9.9.336.1.3.1.1.8
cgspInstDistSccpUnseqrw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.9.9.336.1.3.1.1.9
cgspInstSummaryRoutingExceptionrw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.9.9.336.1.3.1.1.10
cgspInstNumberro
CItpTcInstanceNumber (CISCO-ITP-TC-MIB)
.1.3.6.1.4.1.9.9.336.1.3.1.1.11
cgspInstRouteTableNamerw
CItpTcRouteTableName (CISCO-ITP-TC-MIB)
.1.3.6.1.4.1.9.9.336.1.3.1.1.12
cgspInstRowStatusrw
RowStatus (SNMPv2-TC)
.1.3.6.1.4.1.9.9.336.1.3.1.1.13
cgspInstSccpWrrOpcShiftrw
Unsigned32
.1.3.6.1.4.1.9.9.336.1.3.1.1.14
cgspInstSccpWrrOptionrw
CItpTcSccpWrrOption
.1.3.6.1.4.1.9.9.336.1.3.1.1.15
cgspInstTimerTable
SEQUENCE OF CgspInstTimerTableEntry
.1.3.6.1.4.1.9.9.336.1.3.2
cgspInstTimerTableEntry
CgspInstTimerTableEntry
.1.3.6.1.4.1.9.9.336.1.3.2.1
cgspInstTimerNumber
CgspTimerNumbers
.1.3.6.1.4.1.9.9.336.1.3.2.1.1
cgspInstTimerValuerw
CgspTimerValue UNITS "milliseconds"
.1.3.6.1.4.1.9.9.336.1.3.2.1.2
cgspInstTimerRowStatusrw
RowStatus (SNMPv2-TC)
.1.3.6.1.4.1.9.9.336.1.3.2.1.3
cgspInstUPUTable
SEQUENCE OF CgspInstUPUTableEntry
.1.3.6.1.4.1.9.9.336.1.3.3
cgspInstUPUTableEntry
CgspInstUPUTableEntry
.1.3.6.1.4.1.9.9.336.1.3.3.1
cgspMtp3SI
CItpTcServiceIndicator (CISCO-ITP-TC-MIB)
.1.3.6.1.4.1.9.9.336.1.3.3.1.1
cgspInstSIUPUReceivedro
Counter32 UNITS "MSUs"
.1.3.6.1.4.1.9.9.336.1.3.3.1.2
cgspInstSIUPUTransmittedro
Counter32 UNITS "MSUs"
.1.3.6.1.4.1.9.9.336.1.3.3.1.3
cgspInstUserPartDisplayro
CgspDisplayInstanceUserPart
.1.3.6.1.4.1.9.9.336.1.3.3.1.4
cgspPointCode
OBJECT IDENTIFIER
.1.3.6.1.4.1.9.9.336.1.4
cgspPointCodeTable
SEQUENCE OF CgspPointCodeTableEntry
.1.3.6.1.4.1.9.9.336.1.4.1
cgspPointCodeTableEntry
CgspPointCodeTableEntry
.1.3.6.1.4.1.9.9.336.1.4.1.1
cgspPointCodeNi
CItpTcNetworkIndicator (CISCO-ITP-TC-MIB)
.1.3.6.1.4.1.9.9.336.1.4.1.1.1
cgspPointCodeBin
CItpTcPointCode (CISCO-ITP-TC-MIB)
.1.3.6.1.4.1.9.9.336.1.4.1.1.2
cgspPointCodeTyperw
CItpTcPointCodeType (CISCO-ITP-TC-MIB)
.1.3.6.1.4.1.9.9.336.1.4.1.1.3
cgspPointCodeDisplayro
CItpTcDisplayPC (CISCO-ITP-TC-MIB)
.1.3.6.1.4.1.9.9.336.1.4.1.1.4
cgspPointCodeRowStatusrw
RowStatus (SNMPv2-TC)
.1.3.6.1.4.1.9.9.336.1.4.1.1.5
cgspLinkset
OBJECT IDENTIFIER
.1.3.6.1.4.1.9.9.336.1.5
cgspLinksetTable
SEQUENCE OF CgspLinksetTableEntry
.1.3.6.1.4.1.9.9.336.1.5.1
cgspLinksetTableEntry
CgspLinksetTableEntry
.1.3.6.1.4.1.9.9.336.1.5.1.1
cgspLinksetName
CItpTcLinksetId (CISCO-ITP-TC-MIB)
.1.3.6.1.4.1.9.9.336.1.5.1.1.1
cgspLinksetSourcePointCoderw
CItpTcPointCode (CISCO-ITP-TC-MIB)
.1.3.6.1.4.1.9.9.336.1.5.1.1.2
cgspLinksetSourceDisplayPCro
CItpTcDisplayPC (CISCO-ITP-TC-MIB)
.1.3.6.1.4.1.9.9.336.1.5.1.1.3
cgspLinksetAdjacentPointCoderw
CItpTcPointCode (CISCO-ITP-TC-MIB)
.1.3.6.1.4.1.9.9.336.1.5.1.1.4
cgspLinksetAdjacentDisplayPCro
CItpTcDisplayPC (CISCO-ITP-TC-MIB)
.1.3.6.1.4.1.9.9.336.1.5.1.1.5
cgspLinksetStatero
Enumeration
.1.3.6.1.4.1.9.9.336.1.5.1.1.6
cgspLinksetInboundAclrw
CItpTcAclId (CISCO-ITP-TC-MIB)
.1.3.6.1.4.1.9.9.336.1.5.1.1.7
cgspLinksetOutboundAclrw
CItpTcAclId (CISCO-ITP-TC-MIB)
.1.3.6.1.4.1.9.9.336.1.5.1.1.8
cgspLinksetAccountingMtp3rw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.9.9.336.1.5.1.1.9
cgspLinksetAccountingGttrw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.9.9.336.1.5.1.1.10
cgspLinksetDurationInServicero
Counter32 UNITS "seconds"
.1.3.6.1.4.1.9.9.336.1.5.1.1.12
cgspLinksetDurationOutServicero
Counter32 UNITS "seconds"
.1.3.6.1.4.1.9.9.336.1.5.1.1.13
cgspLinksetActPriorityrw
Unsigned32
.1.3.6.1.4.1.9.9.336.1.5.1.1.14
cgspLinksetDisplayNamerw
SnmpAdminString
.1.3.6.1.4.1.9.9.336.1.5.1.1.15
cgspLinksetDescriptionrw
SnmpAdminString
.1.3.6.1.4.1.9.9.336.1.5.1.1.16
cgspLinksetRotateSlsEnablerw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.9.9.336.1.5.1.1.17
cgspLinksetRotateSlsShiftrw
Unsigned32
.1.3.6.1.4.1.9.9.336.1.5.1.1.18
cgspLinksetProfileNamerw
CgspProfileName
.1.3.6.1.4.1.9.9.336.1.5.1.1.19
cgspLinksetAdjacentInstro
CItpTcNetworkName (CISCO-ITP-TC-MIB)
.1.3.6.1.4.1.9.9.336.1.5.1.1.20
cgspLinksetRowStatusrw
RowStatus (SNMPv2-TC)
.1.3.6.1.4.1.9.9.336.1.5.1.1.21
cgspLinksetTimerTable
SEQUENCE OF CgspLinksetTimerTableEntry
.1.3.6.1.4.1.9.9.336.1.5.2
cgspLinksetTimerTableEntry
CgspLinksetTimerTableEntry
.1.3.6.1.4.1.9.9.336.1.5.2.1
cgspLinksetTimerNumber
CgspTimerNumbers
.1.3.6.1.4.1.9.9.336.1.5.2.1.1
cgspLinksetTimerValuerw
CgspTimerValue UNITS "milliseconds"
.1.3.6.1.4.1.9.9.336.1.5.2.1.2
cgspLinksetTimerRowStatusrw
RowStatus (SNMPv2-TC)
.1.3.6.1.4.1.9.9.336.1.5.2.1.3
Showing 100 of 228 OID objects

CISCO-ITP-GSP-MIB Technical Reference Overview

The CISCO-ITP-GSP-MIB SNMP MIB module published by Cisco defines 228 managed OID objects, including 181 scalar/column metrics, 12 SNMP tables, and 9 trap/notification events anchored at base OID .1.3.6.1.4.1.9.9.336. Key tabular structures include cgspProfileTable, cgspProfileTimerTable, cgspInstanceTable, cgspInstTimerTable, cgspInstUPUTable, cgspPointCodeTable. Monitored SNMP traps/notifications include ciscoGspLinksetStateChange, ciscoGspLinkStateChange, ciscoGspCongestionChange, ciscoGspLinkRcvdUtilChange, ciscoGspLinkSentUtilChange, ciscoGspIsolation.

Key OID Definitions in CISCO-ITP-GSP-MIB

ciscoGspMIBMODULE-IDENTITYnot-accessible
.1.3.6.1.4.1.9.9.336

The MIB for managing Signalling Points and its associated messages transported over Signalling System No. 7 (SS7) Network via Cisco IP Transfer Point. This MIB replaces the CISCO-ITP-SP-MIB and provide support multiple instances of a signalling point within same configuration. The Cisco IP Transfer Point (ITP) is a hardware and software solution that transports SS7 traffic using IP. Each ITP node provides function similar to SS7 Signalling point. The relevant ITU documents describing this technology is the ITU Q series, including ITU Q.700: Introduction to CCITT Signalling System No. 7 and ITU Q.701 Functional description of the message transfer part (MTP) of Signalling System No. 7. This MIB models the GSP as follows: Abbreviations: AERM - Alignment Error Rate Monitor CLLI - Common-Language Location Identification DPC - Destination Point Code GSP - Gateway Signalling Point HSL - High Speed Link (ATM based) LLSC - link set control LSAC - Signalling link activity control LSDA - Signalling data link allocation LSLA - Signalling link activation LSLD - Signalling link deactivation LSLR - Signalling link restoration LSSU - Link Status Signal Unit LSTA - Signalling terminal allocation MTP - Message Transport Protocol MTP2 - Layer 2 of Message Transport Protocol MTP3 - Layer 3 of Message Transport Protocol NTT - The Japanese Nippon Telephone & Telegraph OPC - Originating Point Code PC - Point Code RTN - RouteTableName SCTP - Stream Transmission Protocol(RFC 2960) SIB - Status Indicator Busy SLT - Signalling Link Test SLTA - Signalling Link Test Acknowledgement SP - Signalling Point SS7 - System No. 7 (SS7) Network SUERM - Signal Unit Error Rate Monitor TCBC - Changeback control TCOC - Changeover control TCRC - Controlled rerouting control TFRC - Forced rerouting control TLAC - Link availability control TPRC - Signalling point restart control TRCC - Signalling route set congestion control TSFC - Signalling traffic flow control TSRC - Signalling routing control TTC - The Japanese Telecommunications Technology Committee WRR - Weighted round robin

cgspProfileTableSEQUENCEnot-accessible
.1.3.6.1.4.1.9.9.336.1.2.1

A table that contains the Profiles of signalling points. Entries are added to this table via cgspProfileRowStatus in accordance with the RowStatus convention.

cgspProfileTimerTableSEQUENCEnot-accessible
.1.3.6.1.4.1.9.9.336.1.2.2

A table that contains a profile of timers used to configure SS7 links. Entries are added to this table via cgspProfileTimerRowStatus in accordance with the RowStatus convention.

cgspInstanceTableSEQUENCEnot-accessible
.1.3.6.1.4.1.9.9.336.1.3.1

A table that contains the instances of signalling points. Entries are added to this table via cgspInstRowStatus in accordance with the RowStatus convention.

cgspInstTimerTableSEQUENCEnot-accessible
.1.3.6.1.4.1.9.9.336.1.3.2

A table that contains the timer used to configure an instances of signalling points. Entries are added to this table via cgspInstTimerRowStatus in accordance with the RowStatus convention.

cgspInstUPUTableSEQUENCEnot-accessible
.1.3.6.1.4.1.9.9.336.1.3.3

The Instance UPU table contains information about the number of UPU MSUs transmitted and received for the specific user part(represented by service indicator) and signalling point instance. The user part is primarily represented with the possible service indicator. This table provides the granularity of information required by Q752 table 5.6 and 5.7.

cgspPointCodeTableSEQUENCEnot-accessible
.1.3.6.1.4.1.9.9.336.1.4.1

A table that contains a list of point code defined for the Signalling point defined by this instance. Entries are added to this table via cgspPointCodeRowStatus in accordance with the RowStatus convention.

cgspLinksetTableSEQUENCEnot-accessible
.1.3.6.1.4.1.9.9.336.1.5.1

A table of linksets for this Signalling Point defined by this instance.

cgspLinksetTimerTableSEQUENCEnot-accessible
.1.3.6.1.4.1.9.9.336.1.5.2

A table that contains the timer used to configure timer values specific to a particular linkset. Entries are added to this table via cgspLinksetTimerRowStatus in accordance with the RowStatus convention.

cgspLinkTableSEQUENCEnot-accessible
.1.3.6.1.4.1.9.9.336.1.6.1

A table of links for each Signalling Point.

cgspLinkTimerTableSEQUENCEnot-accessible
.1.3.6.1.4.1.9.9.336.1.6.2

A table that contains the timer used to configure timer values specific to a particular Link. Entries are added to this table via cgspLinkTimerRowStatus in accordance with the RowStatus convention.

cgspLinkRemoteIpAddrTableSEQUENCEnot-accessible
.1.3.6.1.4.1.9.9.336.1.6.3

A table that contains the remote IP addresses used to configure a particular Link. Entries are added to this table via cgspLinkRemoteIpAddrRowStatus in accordance with the RowStatus convention.

cgspLinkUtilTableSEQUENCEnot-accessible
.1.3.6.1.4.1.9.9.336.1.6.4

A table that contains a history of the cgspLinkUtilizationRcvd and cgspLinkUtilizationRcvd objects. In order to properly manage network capacity it is necessary to collect utilization information during short interval. These intervals are less than 5 minutes and can be as low as 1 minute. The number of links supported by a signalling point prevent polling each signalling point to collect information. This table is provided to allow an NMS to collect the information during a normal poll cycle.

ciscoGspLinksetStateChangeNOTIFICATION-TYPEnot-accessible
.1.3.6.1.4.1.9.9.336.0.1

The notification generated when a linkset changes to a new state. The value of cgspLinksetState indicates the new state.

ciscoGspLinkStateChangeNOTIFICATION-TYPEnot-accessible
.1.3.6.1.4.1.9.9.336.0.2

The notification generated when a link changes to a new state. The value of cgspLinkState indicates the new state.

ciscoGspCongestionChangeNOTIFICATION-TYPEnot-accessible
.1.3.6.1.4.1.9.9.336.0.3

The notification generated when a link changes to a new congestion level as specified by cgspLinkCongestionState object for Transmission Side congestion.

ciscoGspLinkRcvdUtilChangeNOTIFICATION-TYPEnot-accessible
.1.3.6.1.4.1.9.9.336.0.4

The notification provide is generated when the cgspLinkUtilStateRcvd changes states.

ciscoGspLinkSentUtilChangeNOTIFICATION-TYPEnot-accessible
.1.3.6.1.4.1.9.9.336.0.5

The notification provide is generated when the cgspLinkUtilStateSent changes states.

ciscoGspIsolationNOTIFICATION-TYPEnot-accessible
.1.3.6.1.4.1.9.9.336.0.6

This notification indicates the instance specified by cgspInstDisplayName and cgspInstDescription has become isolated. All linkset used to connect MTP3 node (instance) are unavailable. Isolation is ended when any linkset supported by this instance reaches the active state.

ciscoGspUPUReceivedNOTIFICATION-TYPEnot-accessible
.1.3.6.1.4.1.9.9.336.0.8

The notification is generated when an UPU MSU is received from a remote signalling point, for a specific instance and user part for the first time in the configured cgspUPUNotifWindowTime. For cases when there is a non-zero number of UPU MSUs received, this notification will be sent at the end of the cgspUPUNotifWindowTime interval, with cgspIntervalUPUs indicating the total count of UPU MSUs received for that specific instance and user part during the entire cgspUPUNotifWindowTime interval Q752/5.6.

ciscoGspUPUTransmittedNOTIFICATION-TYPEnot-accessible
.1.3.6.1.4.1.9.9.336.0.9

The notification is generated when an UPU MSU is transmitted to a remote signalling point, for a specific instance and user part for the first time in the configured cgspUPUNotifWindowTime. For cases when there is a non-zero number of UPU MSUs received, this notification will be sent at the end of the cgspUPUNotifWindowTime interval, with cgspIntervalUPUs indicating the total count of UPU MSUs transmitted for that specific instance and user part during the entire cgspUPUNotifWindowTime interval Q752/5.7.

ciscoGspRxCongestionChangeNOTIFICATION-TYPEnot-accessible
.1.3.6.1.4.1.9.9.336.0.10

The notification generated when a link changes to a new congestion level as specified by cgspLinkRxCongestionstate object for Received side congestion

cgspCLLICodeCItpTcCLLIread-write
.1.3.6.1.4.1.9.9.336.1.1.1

Common-Language Location Identification Codes (CLLI Codes). This object identifies the physical location of this device and can provide additional informaton on the device type.

cgspUtilSampleIntervalCgspSampleIntervalread-write
.1.3.6.1.4.1.9.9.336.1.1.2

This object specifies the time interval used to monitor the utilization of SS7 links. This object in combination with cgspUtilThreshold, cgspLinkPlanCapacitySent and cgspLinkPlanCapacityRcvd will be used to calculate utilization of SS7 links. Changes to the polling interval will take effect after the completion of the current sample interval.

More MIBs from Cisco

Browse all CiscoMIBs →
CISCO-UNIFIED-COMPUTING-COMPUTE-MIB

The CISCO-UNIFIED-COMPUTING-COMPUTE-MIB provides SNMP-based monitoring and management of Cisco UCS compute blades, servers, and chassis components, exposing critical metrics such as CPU utilization, memory usage, thermal sensor readings, power supply status, and interface operational states. This module enables granular visibility into the health and performance of the Cisco Unified Computing System's compute subsystems for capacity planning and fault isolation.

1401 objects→
CISCO-UNIFIED-COMPUTING-STORAGE-MIB

The CISCO-UNIFIED-COMPUTING-STORAGE-MIB facilitates SNMP-based monitoring and management of storage subsystems, including Fibre Channel and iSCSI interfaces, within the Cisco Unified Computing System (UCS) fabric interconnects and blade servers. It exposes critical operational metrics such as port status, error counters, throughput statistics, and storage controller health states to enable granular visibility into the storage infrastructure.

1295 objects→
CISCO-UNIFIED-COMPUTING-VNIC-MIB

The CISCO-UNIFIED-COMPUTING-VNIC-MIB enables SNMP-based monitoring and management of Virtual Network Interface Card (vNIC) attributes, including operational status, traffic counters, and binding configurations, within the Cisco Unified Computing System (UCS) fabric interconnects and server blades.

1161 objects→
CERENT-GENERIC-MIB

SNMP MIB module

984 objects→
CISCO-UNIFIED-COMPUTING-BIOS-MIB

The CISCO-UNIFIED-COMPUTING-BIOS-MIB enables SNMP-based monitoring and configuration of BIOS-level parameters, firmware versions, and hardware initialization states within Cisco Unified Computing System (UCS) servers. It provides visibility into critical server boot diagnostics, BIOS settings, and hardware readiness indicators to facilitate low-level infrastructure management and troubleshooting.

937 objects→
CISCO-UNIFIED-COMPUTING-ETHER-MIB

The CISCO-UNIFIED-COMPUTING-ETHER-MIB provides SNMP management interfaces for monitoring Ethernet interface statistics, link states, and error counters on Cisco Unified Computing System (UCS) fabric interconnects and blade server line cards. This module enables the tracking of physical layer connectivity, port throughput, and packet error rates within the UCS Ethernet switching infrastructure.

920 objects→