Wellfleet-X25-MIB
Detailed view of the defined objects, syntax rules, and hierarchical paths.
241
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
241 total| Object Name |
|---|
wfX25 OBJECT IDENTIFIER .1.3.6.1.4.1.18.3.5.9.4.1 |
RFC1155-SMI Unknown .1.3.6.1.4.1.18.3.5.9.4.1 |
wfX25DeleteCreate/Delete parameter. Default is created.rw Enumeration .1.3.6.1.4.1.18.3.5.9.4.1.1 |
wfX25DisableEnable/Disable parameter. Default is enabled.rw Enumeration .1.3.6.1.4.1.18.3.5.9.4.1.2 |
wfX25StateThe current state of the entire X.25.ro Enumeration .1.3.6.1.4.1.18.3.5.9.4.1.3 |
wfX25ServiceTableThis table describes the services of a circuit on an X.25 line. SEQUENCE OF WfX25ServiceEntry .1.3.6.1.4.1.18.3.5.9.4.2 |
wfX25ServiceEntryAn entry in the X25 Service table. WfX25ServiceEntry .1.3.6.1.4.1.18.3.5.9.4.2.1 |
wfX25ServiceDeleteCreate/Delete parameter, default = created.rw Enumeration .1.3.6.1.4.1.18.3.5.9.4.2.1.1 |
wfX25ServiceDisableEnable/Disable parameter, default = enabled.rw Enumeration .1.3.6.1.4.1.18.3.5.9.4.2.1.2 |
wfX25ServiceSlotSlot number and part of Instance Id.ro INTEGER .1.3.6.1.4.1.18.3.5.9.4.2.1.3 |
wfX25ServiceConnectorConnector number and instance ID member.ro Enumeration .1.3.6.1.4.1.18.3.5.9.4.2.1.4 |
wfX25ServiceLineNumberInstance identifier member. This is the line number assigned
to the driver X.25 is running over. No used in 7.60.ro INTEGER .1.3.6.1.4.1.18.3.5.9.4.2.1.5 |
wfX25ServiceLLIndexInstance identifier member. This is the lower layer index
presented to X25 by the layer immediately below it on the
protocol stack. If the lower layer is a driver, the index
will be 0. Not used in 7.60.ro INTEGER .1.3.6.1.4.1.18.3.5.9.4.2.1.6 |
wfX25ServiceCctCircuit number and instance ID member.ro INTEGER .1.3.6.1.4.1.18.3.5.9.4.2.1.7 |
wfX25ServiceIndexX.25 service entry record ID for this instance.ro INTEGER .1.3.6.1.4.1.18.3.5.9.4.2.1.8 |
wfX25ServiceTypeType of Service.rw Enumeration .1.3.6.1.4.1.18.3.5.9.4.2.1.9 |
wfX25ServiceConnRefUse of Connection Reference Numbers in Call Request
For PDN only, if ON then use wfX25ServiceConnId as
starting reference number for PDN.ro Enumeration .1.3.6.1.4.1.18.3.5.9.4.2.1.10 |
wfX25ServiceConnIdConnection Id to be used in a PTOP Call request. For PDN this will
be the starting number to be used as Connection Id in PDN.rw INTEGER .1.3.6.1.4.1.18.3.5.9.4.2.1.11 |
wfX25ServiceRemoteX121AddrRemote X.121 address for this table entry instance.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.18.3.5.9.4.2.1.12 |
wfX25ServiceRemoteIpAddrRemote IP address for PDN and DDN only.rw IpAddress .1.3.6.1.4.1.18.3.5.9.4.2.1.13 |
wfX25ServiceBCastBroadcast recipient status for this table entry instance.rw Enumeration .1.3.6.1.4.1.18.3.5.9.4.2.1.14 |
wfX25ServiceMaxConnMaximum connections per destination for this table entry instance.rw INTEGER .1.3.6.1.4.1.18.3.5.9.4.2.1.15 |
wfX25ServicePrecedencePrecedence value for this table entry instance. DDN only.rw Enumeration .1.3.6.1.4.1.18.3.5.9.4.2.1.16 |
wfX25ServiceMaxIdleMaximum Idle Time in Minutes for this table entry instance. If 0
is entered the connection stays on forever.rw INTEGER .1.3.6.1.4.1.18.3.5.9.4.2.1.17 |
wfX25ServiceCallRetryInterval in seconds between Call Request to same the destination.
Must be at least 2 times T11/T21 Timer for Packet Level.rw INTEGER .1.3.6.1.4.1.18.3.5.9.4.2.1.18 |
wfX25ServiceFlowFacilityFlow Control negotiation facility parameter for this instance.rw Enumeration .1.3.6.1.4.1.18.3.5.9.4.2.1.19 |
wfX25ServiceWinSizePacket window size parameter for this table entry instance.rw INTEGER .1.3.6.1.4.1.18.3.5.9.4.2.1.20 |
wfX25ServicePktSizePacket size parameter for this table entry instance.rw Enumeration .1.3.6.1.4.1.18.3.5.9.4.2.1.21 |
wfX25ServiceFastSelRequestFast Select Request Facility for this table entry instance.rw Enumeration .1.3.6.1.4.1.18.3.5.9.4.2.1.22 |
wfX25ServiceFastSelAcceptFast Select Accept Facility for this table entry instance.rw Enumeration .1.3.6.1.4.1.18.3.5.9.4.2.1.23 |
wfX25ServiceRevChRequestReverse Charge Request Facility for this table entry instance.rw Enumeration .1.3.6.1.4.1.18.3.5.9.4.2.1.24 |
wfX25ServiceRevChAcceptReverse charge Accept Facility for this table entry instance.rw Enumeration .1.3.6.1.4.1.18.3.5.9.4.2.1.25 |
wfX25ServiceCugFormatClosed User Group Facility Format.rw Enumeration .1.3.6.1.4.1.18.3.5.9.4.2.1.26 |
wfX25ServiceCugTypeClosed User Group Facility Type: Normal CUG,
Bilateral CUG, or Outgoing Access CUG.rw Enumeration .1.3.6.1.4.1.18.3.5.9.4.2.1.27 |
wfX25ServiceCugNumClosed User Group (CUG) number.rw INTEGER .1.3.6.1.4.1.18.3.5.9.4.2.1.28 |
wfX25ServiceUserFacilityAdditional User Supplied Facilities. Must be in Hexadecimal form.rw OCTET STRING .1.3.6.1.4.1.18.3.5.9.4.2.1.29 |
wfX25ServiceValidValidity of the record - updated by X.25.ro Enumeration .1.3.6.1.4.1.18.3.5.9.4.2.1.30 |
wfX25ServiceBFEEnabled if DDNX.25/BFE enabled.rw Enumeration .1.3.6.1.4.1.18.3.5.9.4.2.1.31 |
wfX25ServiceForceCugZeroForce Closed User Group of Zero.rw Enumeration .1.3.6.1.4.1.18.3.5.9.4.2.1.32 |
wfX25ServiceWcpEnableEnable compressionrw Enumeration .1.3.6.1.4.1.18.3.5.9.4.2.1.33 |
wfX25ServiceMUXSet to Enabled to perform 1356 Multiplexing of protocols in the same Vcrw Enumeration .1.3.6.1.4.1.18.3.5.9.4.2.1.34 |
wfX25ServicePtopCallRequestSelect which side of PTOP circuit initiates the connection.
(default = highest X.121 address initiates the call)rw Enumeration .1.3.6.1.4.1.18.3.5.9.4.2.1.35 |
wfX25ServiceVcTypeDetermines whether this service record represents a
Switch Virtual Circuit (SVC) or Permanent Virtual
Circuit (PVC). (default = svc)rw Enumeration .1.3.6.1.4.1.18.3.5.9.4.2.1.36 |
wfX25ServicePvcLcnPVC Logical Channel Number for this service recordrw INTEGER .1.3.6.1.4.1.18.3.5.9.4.2.1.37 |
wfX25ServiceMacPoolStartStarting address of MAC address poolrw OCTET STRING .1.3.6.1.4.1.18.3.5.9.4.2.1.38 |
wfX25ServiceMacPoolSizeThe size of MAC address poolrw INTEGER .1.3.6.1.4.1.18.3.5.9.4.2.1.39 |
wfX25ServiceWindowTimeoutWindow Timeout to detect a dysfunctional VC.rw INTEGER .1.3.6.1.4.1.18.3.5.9.4.2.1.40 |
wfX25ServiceVcBurstThroughputMaximum number of bits of data allowed to be transmitted
for this service record in one second. This value is
divided equally amongst the VCs active for this service
record at any given point in time. A value of 0 indicates
Burst control is not to be applied. The default value is 0.rw INTEGER .1.3.6.1.4.1.18.3.5.9.4.2.1.41 |
wfX25ServiceVcBurstQDepthMaximum number of buffers that can be held in the Burst
Queue while the VC gate pends.rw INTEGER .1.3.6.1.4.1.18.3.5.9.4.2.1.42 |
wfX25ServiceVcPriorityPriority of the VCs associated with this service record.
This value is used to specify whether packets being
transmitted for this VC will be given preference over those
on another VC or not. In the range for this value, 1..9999,
1 signifies highest priority.rw INTEGER .1.3.6.1.4.1.18.3.5.9.4.2.1.43 |
wfX25ServiceVcBurstQClippedPktsTotal Number of packets dropped for VCs of this service
record due to lack of buffers in their respective Burst
Queues.ro Counter .1.3.6.1.4.1.18.3.5.9.4.2.1.44 |
wfX25ServiceVcBurstQPktCntTotal Number of packets stored in the Burst Queues of VCs
of this service record between successive attempts to
forward to the PLP layer.ro Counter .1.3.6.1.4.1.18.3.5.9.4.2.1.45 |
wfX25ServiceVcBurstQHighWaterPktsThe Highest Water Packet Mark of the Burst Queues of VCs
of this service record.ro Gauge .1.3.6.1.4.1.18.3.5.9.4.2.1.46 |
wfX25ServiceVcPktDropsTotal Number of Packets Dropped for VCs of this service
record at the VC level.ro Counter .1.3.6.1.4.1.18.3.5.9.4.2.1.47 |
wfX25ServicePlpPktDropsTotal Number of Packets Dropped by PLP for VCs of this
service record.ro Counter .1.3.6.1.4.1.18.3.5.9.4.2.1.48 |
wfX25ServiceBurstThrPerVcBurst Throughput per VC, dynamically computed as Burst
Throughput confiogured for the service record divided
by number of VCs for the service record in Data Transfer
State.ro INTEGER .1.3.6.1.4.1.18.3.5.9.4.2.1.49 |
wfX25ServiceBackupRecoveryDelayDelay in reverting back to a restored PDN servicerw INTEGER .1.3.6.1.4.1.18.3.5.9.4.2.1.50 |
wfX25ServiceSetupTimeTotal time allowed for setting up a PDN SVC before
attempting a backuprw INTEGER .1.3.6.1.4.1.18.3.5.9.4.2.1.51 |
wfX25ServiceRetryNumberThe number of times a PDN SVC setup will be attempted if
no response is received from the peerrw INTEGER .1.3.6.1.4.1.18.3.5.9.4.2.1.52 |
wfX25BackupInitiationDetermines whether to initiate PDN backup on failure of
any SVC or the last onerw Enumeration .1.3.6.1.4.1.18.3.5.9.4.2.1.53 |
wfX25ServiceEntryNamename of the sevice entryrw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.18.3.5.9.4.2.1.54 |
wfX25VcTableThis is a table of Statistic Entries is per Virtual Circuit. SEQUENCE OF WfX25VcEntry .1.3.6.1.4.1.18.3.5.9.4.4 |
wfX25VcEntryAn entry in the X.25 VC table. WfX25VcEntry .1.3.6.1.4.1.18.3.5.9.4.4.1 |
wfX25VcSlotNumInstance ID and Slot number this VC is on.ro INTEGER .1.3.6.1.4.1.18.3.5.9.4.4.1.1 |
wfX25VcConnectorInstance ID and Connector number this VC is usingro Enumeration .1.3.6.1.4.1.18.3.5.9.4.4.1.2 |
wfX25VcLineNumberInstance identifier member. This is the line number assigned
to the driver X25 is running on top of and this VC is running
on. No used in 7.60ro INTEGER .1.3.6.1.4.1.18.3.5.9.4.4.1.3 |
wfX25VcLLIndexInstance identifier member. This is the lower layer index
presented to X25 by the layer immediately below it on the
protocol stack. If the lower layer is a driver, the index
will be 0. Not used in 7.60.ro INTEGER .1.3.6.1.4.1.18.3.5.9.4.4.1.4 |
wfX25VcCctInstance ID and CCT supporting these VCs. User determines this CCT
via log.ro INTEGER .1.3.6.1.4.1.18.3.5.9.4.4.1.5 |
wfX25VcNumberInstance ID and VC number for this VC. This number corresponds to
the LCN.ro INTEGER .1.3.6.1.4.1.18.3.5.9.4.4.1.6 |
wfX25VcDataTxsNumber of Data Packets sent.ro Counter .1.3.6.1.4.1.18.3.5.9.4.4.1.7 |
wfX25VcInterruptTxsNumber of Interrupt Packets sent.ro Counter .1.3.6.1.4.1.18.3.5.9.4.4.1.8 |
wfX25VcResetTxsNumber of Reset Packets sent.ro Counter .1.3.6.1.4.1.18.3.5.9.4.4.1.9 |
wfX25VcRrTxsNumber of Receiver Ready Packets sent.ro Counter .1.3.6.1.4.1.18.3.5.9.4.4.1.10 |
wfX25VcRnrTxsNumber of Receiver Not Ready Packets sent.ro Counter .1.3.6.1.4.1.18.3.5.9.4.4.1.11 |
wfX25VcRejectTxsNumber of Reject Packets sent.ro Counter .1.3.6.1.4.1.18.3.5.9.4.4.1.12 |
wfX25VcSegmentTxsNumber of Charge Units sent.ro Counter .1.3.6.1.4.1.18.3.5.9.4.4.1.13 |
wfX25VcBytesTxsNumber of Data Bytes sent.ro Counter .1.3.6.1.4.1.18.3.5.9.4.4.1.14 |
wfX25VcIntBytesTxsNumber of Interrupt Data Bytes sent.ro Counter .1.3.6.1.4.1.18.3.5.9.4.4.1.15 |
wfX25VcDataRxsNumber of Data Packets received.ro Counter .1.3.6.1.4.1.18.3.5.9.4.4.1.16 |
wfX25VcInterruptRxsNumber of Interrupt Packets received.ro Counter .1.3.6.1.4.1.18.3.5.9.4.4.1.17 |
wfX25VcResetRxsNumber of Reset Packets received.ro Counter .1.3.6.1.4.1.18.3.5.9.4.4.1.18 |
wfX25VcRrRxsNumber of Receiver Ready Packets received.ro Counter .1.3.6.1.4.1.18.3.5.9.4.4.1.19 |
wfX25VcRnrRxsNumber of Receiver Not Ready Packets received.ro Counter .1.3.6.1.4.1.18.3.5.9.4.4.1.20 |
wfX25VcRejectRxsNumber of Reject Packets received.ro Counter .1.3.6.1.4.1.18.3.5.9.4.4.1.21 |
wfX25VcSegmentRxsNumber of Charge Units received.ro Counter .1.3.6.1.4.1.18.3.5.9.4.4.1.22 |
wfX25VcBytesRxsNumber of Data Bytes received.ro Counter .1.3.6.1.4.1.18.3.5.9.4.4.1.23 |
wfX25VcIntBytesRxsNumber of Interrupt Data Bytes received.ro Counter .1.3.6.1.4.1.18.3.5.9.4.4.1.24 |
wfX25VcApPktsDroppedNumber of Application/redirector Packets Dropedro Counter .1.3.6.1.4.1.18.3.5.9.4.4.1.25 |
wfX25VcRemoteX121AddrRemote DTE Address for this connectionro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.18.3.5.9.4.4.1.26 |
wfX25VcBurstQClippedPktsNumber of packets dropped for this VC due to lack of
buffers in the Burst Queue. Packets are only dropped
when the value of the statistic wfX25VcBurstQPktCnt is
equal to wfX25ServiceVcBurstQDepth.ro Counter .1.3.6.1.4.1.18.3.5.9.4.4.1.27 |
wfX25VcBurstQPktCntNumber of packets stored for this VC in the Burst Queue
between successive attempts to forward to the PLP layer.
This statistic is indicative of the transient loading of
buffering mechanism between the PLP layer and the upper
layers. The maximum value that this statistic can reach
is determined by the setting of wfX25ServiceVcMaxBufCnt.
When the value of this statistic is equal to
wfX25ServiceVcBurstQDepth, all subsequently arriving
packets are dropped.ro Counter .1.3.6.1.4.1.18.3.5.9.4.4.1.28 |
wfX25VcBurstQHighWaterPktsHigh Water Packet Mark for the Burst Queue of this VC.ro Gauge .1.3.6.1.4.1.18.3.5.9.4.4.1.29 |
wfX25VcPktsLargerThanBurstThrCntTotal Number of Packets serviced on this VC which are
larger than the computed burst throughput per VC.
The burst throughput per VC is computed as
wfX25ServiceVcBurstThroughput / No. of Active VCs for the
service record.ro Counter .1.3.6.1.4.1.18.3.5.9.4.4.1.30 |
wfX25VcPktDropsTotal Number of Packets Dropped on this VC.
These drops are caused by insufficient resources
being available to forward the packets to the PLP layer.ro Counter .1.3.6.1.4.1.18.3.5.9.4.4.1.31 |
wfX25VcPlpPktDropsTotal Number of Packets Dropped by PLP on this VC.
These drops are due to either the line being disabled or the
lack of buffering to store packets for transmission.ro Counter .1.3.6.1.4.1.18.3.5.9.4.4.1.32 |
wfX25VcMbsOutstandingNumber of packets sent to the PLP layer from the upper layer
that have not yet been added to the local assembly/deassembly
queue at the PLP layer. These packets will require additional
processing at a later time. This value is set after the PLP
layer has completed processing of the maximum allowable number
of packets received from the upper layer.ro Counter .1.3.6.1.4.1.18.3.5.9.4.4.1.33 |
wfX25VcMbsOutstandingPostTxNumber of buffers sent to the PLP layer that have not yet been
added to the local asembly/deassembly queue. This value
is set after the PLP layer has completed transmission of the
maximum allowable number of packets from the local assembly/
deassembly queue to the lower layer.ro Counter .1.3.6.1.4.1.18.3.5.9.4.4.1.34 |
wfX25VcMaxTxMaximum Number of buffers that can be sent from the upper
layer to the PLP layer at any one time without overflowing
the local assembly/desasembly queue.ro Counter .1.3.6.1.4.1.18.3.5.9.4.4.1.35 |
wfX25VcMbsQueueCntNumber of buffers sent to the PLP layer that are currently
on the local assembly/deassembly queue at the PLP layer.
This value is set after the PLP layer has completed processing
of the maximum allowable number of packets received from the
upper layer.ro Counter .1.3.6.1.4.1.18.3.5.9.4.4.1.36 |
wfX25VcMbsQueueCntPostTxNumber of buffers sent to the PLP layer that have not yet
been added to the local assembly/deassembly queue. This value
is set after the PLP layer has completed transmission of the
maximum allowable number of packets from the local assembly/
deassembly queue to the lower layer.ro Counter .1.3.6.1.4.1.18.3.5.9.4.4.1.37 |
wfX25VcTxQueueCntNumber of buffers sent to the PLP layer that are currently
on the transmit queue at the PLP layer. This value is set
after the PLP layer has completed processing of the maximum
allowable number of packets received from upper layer.ro Counter .1.3.6.1.4.1.18.3.5.9.4.4.1.38 |
wfX25VcTxQueueCntPostTxNumber of buffers sent to the PLP layer that are currently
on thequeue to transmit at the PLP layer. This value is set
after the PLP layer has completed transmission of the maximum
allowable number of packets from the local assembly/deassembly
queue to the lower layer.ro Counter .1.3.6.1.4.1.18.3.5.9.4.4.1.39 |
wfLapbPktTableThe table of LAPB PKT Level Parameters SEQUENCE OF WfLapbPktEntry .1.3.6.1.4.1.18.3.5.9.4.5 |
wfLapbPktEntryAn entry in the LAPB PKT table WfLapbPktEntry .1.3.6.1.4.1.18.3.5.9.4.5.1 |
wfLapbPktDeleteCreate/Delete parameter. Default is created.rw Enumeration .1.3.6.1.4.1.18.3.5.9.4.5.1.1 |
wfLapbPktDisableEnable/Disable parameterrw Enumeration .1.3.6.1.4.1.18.3.5.9.4.5.1.2 |
wfLapbPktSlotNumInstance identifier. This is the slot number where this X.25 packet
layer is running.ro INTEGER .1.3.6.1.4.1.18.3.5.9.4.5.1.3 |
wfLapbPktConnectorInstance identifier. This is the Physical connector number for the Physical
layer associated with this X25 Packet layer.ro INTEGER .1.3.6.1.4.1.18.3.5.9.4.5.1.4 |
wfLapbPktLineNumberInstance identifier. This is the line number assigned to the LAPB Driver
associated with this X25 Packet Layer. Not used in 7.60ro INTEGER .1.3.6.1.4.1.18.3.5.9.4.5.1.5 |
wfLapbPktLLIndexInstance identifier. This is the lower layer index presented to X25 by
the layer immediately below it on the protocol stack. If the lower layer
is a driver, the index will be 0. Not used in 7.60.ro INTEGER .1.3.6.1.4.1.18.3.5.9.4.5.1.6 |
wfLapbPktLapbCctCircuit number of Lapb (SYNC) driver associated with this X25 Packet Layerro INTEGER .1.3.6.1.4.1.18.3.5.9.4.5.1.7 |
wfLapbPktLinkIdAccess Link identifier - index into line information array.ro INTEGER .1.3.6.1.4.1.18.3.5.9.4.5.1.8 |
wfLapbPktLineStateReflects the state of the X.25 packet layer that is associated with this
network record. When the state of this parameter is set to Up, the router
can transfer data between the line layer and the packet layer. Note that
this parameter is used internally; it does NOT reflect the status of the
underlying synchronous circuit.ro Enumeration .1.3.6.1.4.1.18.3.5.9.4.5.1.9 |
wfLapbPktSeqSizeSequence numbering scheme for the data packets. Modulo 8 or Modulo 128rw Enumeration .1.3.6.1.4.1.18.3.5.9.4.5.1.10 |
wfLapbPktMaxWindowMaximum window size that can be negotiated on a per call basis, if the
flow control facility is subscribed too. Extended window size of 127
can be used if wfLapbPktSeqSize is 128. Otherwise the maximum is 7.
This attribute is effective only if the attribute wfLapbPktFloCtl is
set to 'ON'.rw INTEGER .1.3.6.1.4.1.18.3.5.9.4.5.1.11 |
wfLapbPktMaxLengthMaximum packet length that can be negotiated on a per call basis, if
the flow control facility is subscribed too. This attribute is effective
only if the attribute wfLapbPktFloCtl is set to 'ON'. This attribute
should not be greater than the wfSYNCEntry attribute wfSyncMtu.rw Enumeration .1.3.6.1.4.1.18.3.5.9.4.5.1.12 |
wfLapbPktMaxThroughputMaximum throughput class value that can be negotiated on a per call basis,
if the throughput class negotiation facility is subscribed too. For this
to be effective the attribute wfLapbPktThroughput must be set to ON.rw Enumeration .1.3.6.1.4.1.18.3.5.9.4.5.1.13 |
wfLapbPktFlowCtlFlow control parameter negotiation facility subscriptionrw Enumeration .1.3.6.1.4.1.18.3.5.9.4.5.1.14 |
wfLapbPktThroughputThroughput class negotiation facility subscriptionrw Enumeration .1.3.6.1.4.1.18.3.5.9.4.5.1.15 |
wfLapbPktUserIdentityNetwork user identification (NUI) related facility subscriptionrw Enumeration .1.3.6.1.4.1.18.3.5.9.4.5.1.16 |
wfLapbPktInCallsSpecifies whether or not (ON/OFF) incoming calls are permittedrw Enumeration .1.3.6.1.4.1.18.3.5.9.4.5.1.17 |
wfLapbPktOutCallsSpecifies whether or not (ON/OFF) outgoing calls are permittedrw Enumeration .1.3.6.1.4.1.18.3.5.9.4.5.1.18 |
wfLapbPktFastAcceptSpecifies whether or not (ON/OFF) fast select acceptance facility is
subscribed too.rw Enumeration .1.3.6.1.4.1.18.3.5.9.4.5.1.19 |
wfLapbPktReverseAcceptSpecifies whether or not (ON/OFF) reverse charge aceptance facility is
subscribed to. If this is set this packet layer will simply accept calls
with reverse charge facility. But the packet layer (router) will not
provide any charging information.rw Enumeration .1.3.6.1.4.1.18.3.5.9.4.5.1.20 |
wfLapbPktFastSelectSpecifies whether or not (ON/OFF) fast select facility is allowed on
a per call basis.rw Enumeration .1.3.6.1.4.1.18.3.5.9.4.5.1.21 |
wfLapbPktReverseChargingSpecifies whether or not (ON/OFF) reverse charging facility is allowed
on a per call basis.rw Enumeration .1.3.6.1.4.1.18.3.5.9.4.5.1.22 |
wfLapbPktCugSelectionFormat of the Closed User Group (CUG) related facilities supported.rw Enumeration .1.3.6.1.4.1.18.3.5.9.4.5.1.23 |
wfLapbPktCugOASpecifies whether or not CUG with Outgoing access selection facility
is supported.rw Enumeration .1.3.6.1.4.1.18.3.5.9.4.5.1.24 |
wfLapbPktCugBilateralSpecifies whether or not Bilateral Closed User Group related facility
is supported. If this is set, then the wfLapbPktCugSelection should be
set to EXTENDED.rw Enumeration .1.3.6.1.4.1.18.3.5.9.4.5.1.25 |
wfLapbPktRpoaSelectionSpecifies whether or not RPOA related facility is supported. Outgoing
calls will not contain any RPOA facility. But if set this packet layer
will simply accept calls with RPOA related facility.rw Enumeration .1.3.6.1.4.1.18.3.5.9.4.5.1.26 |
wfLapbPktChargeInformSpecifies whether or not the charging information related facilities
are supported. Outgoing calls will not contain the charge information
related facility. But if set this packet layer will simply accept calls
with the charge information related facility. No charging information
will be collected.rw Enumeration .1.3.6.1.4.1.18.3.5.9.4.5.1.27 |
wfLapbPktTransitDelayTransit delay indication facility. If set, accept calls with this
facility.rw Enumeration .1.3.6.1.4.1.18.3.5.9.4.5.1.28 |
wfLapbPktFullAddressingIf this attribute is set, the full local X121 address (calling address)
is supplied in the outgoing call request and the X.25 network also expected
to provide the full called address in the incoming call packet.rw Enumeration .1.3.6.1.4.1.18.3.5.9.4.5.1.29 |
wfLapbPktAccFormatSpecifies the format of the call accepted packet.rw Enumeration .1.3.6.1.4.1.18.3.5.9.4.5.1.30 |
wfLapbPktRelFormatConnection release format - format of Clear Requestsrw Enumeration .1.3.6.1.4.1.18.3.5.9.4.5.1.31 |
wfLapbPktT1Local confirmation timeouts in seconds. This timer represents the
following CCITT timers.
If DCE: T10 (restart), T12 (reset), T13 (clear)
If DTE: T20 (restart), T22 (reset), T23 (clear)rw INTEGER .1.3.6.1.4.1.18.3.5.9.4.5.1.32 |
wfLapbPktT2Call confirmation time out in seconds. This represent the CCITT T11
timer for the DCE and T21 timer for the DTE.rw INTEGER .1.3.6.1.4.1.18.3.5.9.4.5.1.33 |
wfLapbPktT3Congestion or busy condition watchdog timer in milliseconds. When system
resources needed for packet assembly/deassembly depleted, this timer is
set to reenter the PLP state machine to retry. User should use extreme
caution in manipulating this timer.rw INTEGER .1.3.6.1.4.1.18.3.5.9.4.5.1.34 |
wfLapbPktT4Data packet transmission watchdog timer in milliseconds. This is the
delay for acknowledgement. It is used to reenter PLP state machine also.
User should use extreme caution in manipulating this timer.rw INTEGER .1.3.6.1.4.1.18.3.5.9.4.5.1.35 |
wfLapbPktIwcCntNumber of IWC (Incoming VC's) defined on this access link.rw INTEGER .1.3.6.1.4.1.18.3.5.9.4.5.1.36 |
wfLapbPktIwcIdLow LCN ID for IWC (Incoming VC's) defined on this access link.rw INTEGER .1.3.6.1.4.1.18.3.5.9.4.5.1.37 |
wfLapbPktBwcCntNumber of BWC (Bidirectional VC's) defined on this access link.rw INTEGER .1.3.6.1.4.1.18.3.5.9.4.5.1.38 |
wfLapbPktBwcIdLow LCN ID for BWC (Bidirectional VC's) defined on this access link.rw INTEGER .1.3.6.1.4.1.18.3.5.9.4.5.1.39 |
wfLapbPktOwcCntNumber of OWC (Outgoing VC's) defined on this access link.rw INTEGER .1.3.6.1.4.1.18.3.5.9.4.5.1.40 |
wfLapbPktOwcIdLow LCN ID for OWC (Outgoing VC's) defined on this access link.rw INTEGER .1.3.6.1.4.1.18.3.5.9.4.5.1.41 |
wfLapbPktDefWindowNon standard default transmit/receive window size.rw INTEGER .1.3.6.1.4.1.18.3.5.9.4.5.1.42 |
wfLapbPktDefLengthNon standard default transmit/receive packet size. This attribute should
not be greater than the wfSyncEntry attribute wfSyncMtu.rw Enumeration .1.3.6.1.4.1.18.3.5.9.4.5.1.43 |
wfLapbPktDefClassNon standard default transmit/receive throughput class assignment.rw INTEGER .1.3.6.1.4.1.18.3.5.9.4.5.1.44 |
wfLapbPktDxeSpecify type of local X25 interface and imply subsequent rules of X.25.
DXE_X25DTERSTA ->DTE mode with Restart Procedure.
DXE_X25DTE ->DTE mode without any restart procedure
DXE_X25DCE ->DCE mode with restart procedure
DXE_X25DTEDXE ->DTE/DTE environment, unassigned roles.rw Enumeration .1.3.6.1.4.1.18.3.5.9.4.5.1.45 |
wfLapbPktConformanceCCITT conformance recommendation used on each line.rw Enumeration .1.3.6.1.4.1.18.3.5.9.4.5.1.46 |
wfLapbPktStandardNetwork Standard to be used on each line.rw Enumeration .1.3.6.1.4.1.18.3.5.9.4.5.1.47 |
wfLapbPktNetaddrThis Link's Network address (X121 address).ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.18.3.5.9.4.5.1.48 |
wfLapbPktStatisticsGives the user the ability to Turn ON or Shut OFF statistics computation.
This can be shut off for better performance on the line. Now it also
provides a small packet trace function.rw Enumeration .1.3.6.1.4.1.18.3.5.9.4.5.1.49 |
wfLapbPktNetaddrTypeThis defines whether the Network connection is to a DDN network or
PDN Network. This is used to decide how the Local X121 Network address is
derived. If this attribute is set to DDN the Local X121 address used in
the attribute wfLapbPktNetaddr will be derived from the user supplied
IP address. Otherwise the X121 address should be supplid by the user.rw Enumeration .1.3.6.1.4.1.18.3.5.9.4.5.1.50 |
wfLapbPktDDNIpAddrIf the wfLapbPktNetaddrType is DDNTYPE or DDN_BFE this is the user
supplied local IP address. The router will convert this to the
corresponding X121 address and the X121 address value will be put
in wfLapbPktNetaddr attribute.rw IpAddress .1.3.6.1.4.1.18.3.5.9.4.5.1.51 |
wfLapbPktPDNX121AddrIf the wfLapbPktNetaddrType is PDNTYPE this is the user supplied local
X.121 address. The router will put this value in wfLapbPktNetaddr
attribute.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.18.3.5.9.4.5.1.52 |
wfLapbPktTxT5Tx window size transmit delay timerrw INTEGER .1.3.6.1.4.1.18.3.5.9.4.5.1.53 |
wfLapbPktUseDfltServiceIndicates whether or not to use the default ddn service.rw Enumeration .1.3.6.1.4.1.18.3.5.9.4.5.1.54 |
wfLapbPktPVCCntNumber of PVCs defined on this access link.rw INTEGER .1.3.6.1.4.1.18.3.5.9.4.5.1.55 |
wfLapbPktPVCLowLcnLow LCN ID for PVCs defined on this access link.rw INTEGER .1.3.6.1.4.1.18.3.5.9.4.5.1.56 |
wfLapbPktClientTimerClient application response timeout period in seconds.
This timer allows for the extended delays that can occur
negotiating with remote clients (e.g., IPEX or QLLC).
This timer must be greater than the wfLapbPktT3 period
and less than wfLapbPktT2.rw INTEGER .1.3.6.1.4.1.18.3.5.9.4.5.1.57 |
wfLapbPktPduSizeThe X.25 PDU Size for this logical channel. This PDU size
represents the M_BUF_SIZE used for X.25 Fragmentation
and Reassembly in the packet layer. This is the largest
message size X.25 will handle from a client on a given
Logical Channel. Changing this attribute enables X.25
to handle client messages up to 4096 bytes in lengthrw INTEGER .1.3.6.1.4.1.18.3.5.9.4.5.1.58 |
wfLapbPktTranspacCauseCodeEnableUse Transpac Cause Codes , default = disabled.rw Enumeration .1.3.6.1.4.1.18.3.5.9.4.5.1.59 |
wfLapbPktTxMbsQueueThresholdThe maximum number of packets that TX mbs queue can hold.
If X.25 receives more packets and TX mbs queue count
reaches this maximum, it will open up another SVC connection.
The default is zero and the maximum queue count is equal to
wfLapbPktDefWindow + 1, which is three.rw INTEGER .1.3.6.1.4.1.18.3.5.9.4.5.1.60 |
wfLapbPktBackupDebugLvlDebug level for X.25 backup messagesrw Enumeration .1.3.6.1.4.1.18.3.5.9.4.5.1.61 |
wfLapbPktBackupEnableBackup Enable/Disable parameterrw Enumeration .1.3.6.1.4.1.18.3.5.9.4.5.1.62 |
wfLapbPktStatsTableThe table of LAPB PKT Level Statistics. SEQUENCE OF WfLapbPktStatsEntry .1.3.6.1.4.1.18.3.5.9.4.6 |
wfLapbPktStatsEntryPacket level statistics. WfLapbPktStatsEntry .1.3.6.1.4.1.18.3.5.9.4.6.1 |
wfLapbPktStatsSlotNumSlot number and instance ID for this Lapb Packet Layer Line instance.ro INTEGER .1.3.6.1.4.1.18.3.5.9.4.6.1.1 |
wfLapbPktStatsConnectorPort number and instance ID for this Lapb Packet Layer Line instance.ro INTEGER .1.3.6.1.4.1.18.3.5.9.4.6.1.2 |
wfLapbPktStatsLineNumberInstance identifier member. This is the line number assigned to the
driver X.25 is running over. No used in 7.60ro INTEGER .1.3.6.1.4.1.18.3.5.9.4.6.1.3 |
wfLapbPktStatsLLIndexInstance identifier member. This is the lower layer index
presented to X25 by the layer immediately below it on the
protocol stack. If the lower layer is a driver, the index
will be 0. Not used in 7.60.ro INTEGER .1.3.6.1.4.1.18.3.5.9.4.6.1.4 |
wfLapbPktStatsCctCircuit number for this instance.ro INTEGER .1.3.6.1.4.1.18.3.5.9.4.6.1.5 |
wfLapbPktStatsLineAddressThe local X.121 address of this line.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.18.3.5.9.4.6.1.6 |
wfLapbPktStatsMaxVcsMaximum number of Virtual Circuits allowed on this line.ro Counter .1.3.6.1.4.1.18.3.5.9.4.6.1.7 |
wfLapbPktStatsActiveVcsNumber of Active Virtual Circuits on this line.ro Counter .1.3.6.1.4.1.18.3.5.9.4.6.1.8 |
wfLapbPktStatsActiveMaxHighest number of active Virtual Circuits on this line.ro Counter .1.3.6.1.4.1.18.3.5.9.4.6.1.9 |
wfLapbPktStatsTotalConnectionsNumber of Total Virtual Connections performed since start up.ro Counter .1.3.6.1.4.1.18.3.5.9.4.6.1.10 |
wfLapbPktStatsFailedConnectionsNumber of unsuccessful Virtual Connections performed since start up.ro Counter .1.3.6.1.4.1.18.3.5.9.4.6.1.11 |
wfLapbPktStatsNormalDisconnectsNumber of Normal Virtual Circuit Disconnections.ro Counter .1.3.6.1.4.1.18.3.5.9.4.6.1.12 |
wfLapbPktStatsAbnormalDisconnectsNumber of Abnormal Virtual Circuit Disconnections.ro Counter .1.3.6.1.4.1.18.3.5.9.4.6.1.13 |
wfLapbPktStatsDataTxsNumber of Data Packets Transmitted on this line.ro Counter .1.3.6.1.4.1.18.3.5.9.4.6.1.14 |
wfLapbPktStatsInterruptTxsNumber of Interrupt Packets sent.ro Counter .1.3.6.1.4.1.18.3.5.9.4.6.1.15 |
wfLapbPktStatsResetTxsNumber of Reset Requests sent.ro Counter .1.3.6.1.4.1.18.3.5.9.4.6.1.16 |
wfLapbPktStatsRrTxsNumber of Receiver Ready Packets sent.ro Counter .1.3.6.1.4.1.18.3.5.9.4.6.1.17 |
wfLapbPktStatsRnrTxsNumber of Receiver Not Ready Packets sent.ro Counter .1.3.6.1.4.1.18.3.5.9.4.6.1.18 |
wfLapbPktStatsRejectTxsNumber of Reject Packets sent.ro Counter .1.3.6.1.4.1.18.3.5.9.4.6.1.19 |
wfLapbPktStatsRestartTxsNumber of Restart Packets sent.ro Counter .1.3.6.1.4.1.18.3.5.9.4.6.1.20 |
wfLapbPktStatsDiagTxsNumber of Diagnostic Packets sent.ro Counter .1.3.6.1.4.1.18.3.5.9.4.6.1.21 |
wfLapbPktStatsSegmentTxsNumber of Charge Units sent.ro Counter .1.3.6.1.4.1.18.3.5.9.4.6.1.22 |
wfLapbPktStatsBytesTxsNumber of Data Bytes sent.ro Counter .1.3.6.1.4.1.18.3.5.9.4.6.1.23 |
wfLapbPktStatsIntBytesTxsNumber of Interrupt Data Bytes sent.ro Counter .1.3.6.1.4.1.18.3.5.9.4.6.1.24 |
wfLapbPktStatsDataRxsNumber of Data Packets received on this line.ro Counter .1.3.6.1.4.1.18.3.5.9.4.6.1.25 |
wfLapbPktStatsInterruptRxsNumber of Interrupt Packets received.ro Counter .1.3.6.1.4.1.18.3.5.9.4.6.1.26 |
wfLapbPktStatsResetRxsNumber of Reset Requests received.ro Counter .1.3.6.1.4.1.18.3.5.9.4.6.1.27 |
wfLapbPktStatsRrRxsNumber of Receiver Ready Packets received.ro Counter .1.3.6.1.4.1.18.3.5.9.4.6.1.28 |
wfLapbPktStatsRnrRxsNumber of Receiver Not Ready Packets received.ro Counter .1.3.6.1.4.1.18.3.5.9.4.6.1.29 |
wfLapbPktStatsRejectRxsNumber of Reject Packets received.ro Counter .1.3.6.1.4.1.18.3.5.9.4.6.1.30 |
wfLapbPktStatsRestartRxsNumber of Restart Packets received.ro Counter .1.3.6.1.4.1.18.3.5.9.4.6.1.31 |
wfLapbPktStatsDiagRxsNumber of Diagnostic Packets received.ro Counter .1.3.6.1.4.1.18.3.5.9.4.6.1.32 |
wfLapbPktStatsSegmentRxsNumber of Charge Units received.ro Counter .1.3.6.1.4.1.18.3.5.9.4.6.1.33 |
wfLapbPktStatsBytesRxsNumber of Data Bytes received.ro Counter .1.3.6.1.4.1.18.3.5.9.4.6.1.34 |
wfLapbPktStatsIntBytesRxsNumber of Interrupt Data Bytes received.ro Counter .1.3.6.1.4.1.18.3.5.9.4.6.1.35 |
wfLapbPktStatsOnOffSwitchThis tells the user if Statistics Computation is turned ON or OFF.ro INTEGER .1.3.6.1.4.1.18.3.5.9.4.6.1.36 |
wfX25PvcServiceTablethe table of Lapb Pvc Packet level parameters SEQUENCE OF WfX25PvcServiceEntry .1.3.6.1.4.1.18.3.5.9.4.7 |
wfX25PvcServiceEntryAn entry in the LAPB PKT table WfX25PvcServiceEntry .1.3.6.1.4.1.18.3.5.9.4.7.1 |
wfX25PvcDeleteCreate/Delete parameter, Default is createdrw Enumeration .1.3.6.1.4.1.18.3.5.9.4.7.1.1 |
wfX25PvcDisableEnable/Disable Parameterrw Enumeration .1.3.6.1.4.1.18.3.5.9.4.7.1.2 |
wfX25SlotNumPart of the Instance Identifier. This is the slot number where this
X25 packet layer is runningro INTEGER .1.3.6.1.4.1.18.3.5.9.4.7.1.3 |
wfX25ConnectorPart of the Instance Identifier. This is the physical connector number
for the physical layer associated with this packet layerro INTEGER .1.3.6.1.4.1.18.3.5.9.4.7.1.4 |
wfX25LineNumberPart of the Instance Id. This is the line number assigned to the LAPB
driver associated with the X25 Packet layer.ro INTEGER .1.3.6.1.4.1.18.3.5.9.4.7.1.5 |
wfX25LLIndexInstance identifier. This is the lower layer index presented to X25 by
the layer immediately below it on the protocol stack. If the lower layer
is a driver, the index will be 0. Not used in 7.60.ro INTEGER .1.3.6.1.4.1.18.3.5.9.4.7.1.6 |
wfX25PvcServiceCctInstance Id. This is the Circuit numberro INTEGER .1.3.6.1.4.1.18.3.5.9.4.7.1.7 |
wfX25PvcServiceIndexInstace Id. This is the lcn on which this pvc is runningro INTEGER .1.3.6.1.4.1.18.3.5.9.4.7.1.8 |
wfX25PvcServiceTypeType of Service for this PVC Service recordrw Enumeration .1.3.6.1.4.1.18.3.5.9.4.7.1.9 |
wfX25PvcRxDefWindowThis is the receive window size used for setting up the pvc.rw INTEGER .1.3.6.1.4.1.18.3.5.9.4.7.1.10 |
wfX25PvcTxDefWindowThis is the transmit window size used for setting up the pvc.rw INTEGER .1.3.6.1.4.1.18.3.5.9.4.7.1.11 |
wfX25PvcRxDefLengthThis is the receive packet size.rw Enumeration .1.3.6.1.4.1.18.3.5.9.4.7.1.12 |
wfX25PvcTxDefLengthThis is the trasmit packet sizerw Enumeration .1.3.6.1.4.1.18.3.5.9.4.7.1.13 |
wfX25PvcRxDefClassThis is the receive througput class value that can be used on a per pvc
basis. For this to be effective, the wfX25Throughput must be set
ONrw Enumeration .1.3.6.1.4.1.18.3.5.9.4.7.1.14 |
wfX25PvcTxDefClassThis is the transmit througput class value that can be used on a per pvc
basis. For this to be effective, the wfX25Throughput must be set
ONrw Enumeration .1.3.6.1.4.1.18.3.5.9.4.7.1.15 |
wfX25QllcAddrMapTabletable of X.121 address to LLC Mac address mappings. SEQUENCE OF WfX25QllcAddrMapEntry .1.3.6.1.4.1.18.3.5.9.4.8 |
wfX25QllcAddrMapEntryAn entry in the QLLC Address Mapping table WfX25QllcAddrMapEntry .1.3.6.1.4.1.18.3.5.9.4.8.1 |
wfX25QllcAddrMapDeleteCreate/Delete parameter.rw Enumeration .1.3.6.1.4.1.18.3.5.9.4.8.1.1 |
wfX25QllcAddrMapDisableEnable/Disable parameter.rw Enumeration .1.3.6.1.4.1.18.3.5.9.4.8.1.2 |
wfX25QllcAddrMapStateThe current state of the QLLC Mapping.ro Enumeration .1.3.6.1.4.1.18.3.5.9.4.8.1.3 |
wfX25QllcAddrMapCctCircuit number and instance ID member.ro INTEGER .1.3.6.1.4.1.18.3.5.9.4.8.1.4 |
wfX25QllcAddrMapIndexX.25 QLLC Address Map entry record ID for this instance.ro INTEGER .1.3.6.1.4.1.18.3.5.9.4.8.1.5 |
wfX25QllcAddrMapPartnerX121The X.121 address of a X.25 device emulated by this
interface.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.18.3.5.9.4.8.1.6 |
wfX25QllcAddrMapAdjacentX121The X.121 address of a X.25 device connecting thru this
interface. This address may contain wildcard characters.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.18.3.5.9.4.8.1.7 |
wfX25QllcAddrMapPidQLLC Protocol ID used in the first byte of Call User
Data of the X.25 Call Request packet.rw INTEGER .1.3.6.1.4.1.18.3.5.9.4.8.1.8 |
wfX25QllcAddrMapPartnerMacThe LLC MAC address of a LLC device connecting thru this
interface. The LLC MAC address may contain wildcard
characters, see wfX25QllcAddrMapOptions attribute below.rw OCTET STRING .1.3.6.1.4.1.18.3.5.9.4.8.1.9 |
wfX25QllcAddrMapPartnerSapThe SAP of a LLC device connecting thru this interface.rw INTEGER .1.3.6.1.4.1.18.3.5.9.4.8.1.10 |
wfX25QllcAddrMapAdjacentMacThe LLC MAC address of a LLC device emulated by this
interface. If set to nil, a LLC MAC address will be
dynamically assign by X.25 from an address pool defined
in the X.25 Service Record.rw OCTET STRING .1.3.6.1.4.1.18.3.5.9.4.8.1.11 |
wfX25QllcAddrMapAdjacentSapThe SAP of a LLC device emulated by this interface.rw INTEGER .1.3.6.1.4.1.18.3.5.9.4.8.1.12 |
wfX25QllcAddrMapOptionsThis object is a bitmask, setting individual bit postions
enable the option. Values may be added together to
enable multiple options.
Hex Dec
Value Value Options
-
0x0001 1 Do not wait for Adjacent DTE/DCE to send
an QXID before forwarding an QXID to it.
0x0002 2 Enable when SDLC endstations are connecting
to QLLC hosts that do not support receipt of
XID polls and do not retransmit XIDs.
0x0004 4 wfX25QllcAddrMapPartnerMac field contains
wildcard characters.rw INTEGER .1.3.6.1.4.1.18.3.5.9.4.8.1.13 |
wfX25QllcAddrMapTraceThis object is a bitmask, setting individual bit postions
enable logging of internal QLLC messages and events.
Values may be added together to enable multiple message
groups.
Hex Dec
Value Value Message/Event
-
0x0001 1 Enable QLLC logging.
0x0002 2 Data frames/packets.
0x0004 4 Flow Control messages.
0x0008 8 Client registration messages.
0x0010 16 X.25 session establishment messages.
0x0020 32 Test frames/packets.
0x0040 64 XID frames/packes.
0x0080 128 Set Mode frames/packets.
0x0100 256 Disconnect frames/packets.
0x0200 512 Configuration changes.
0x0400 1024 Death of client (DLSw or APPN).
0x0800 2048 Data Path (DP) messages.rw INTEGER .1.3.6.1.4.1.18.3.5.9.4.8.1.14 |
wfX25QllcAddrMapPuTypePU type (T2.0 or T2.1) of the locally attached QLLC device.rwobsolete Enumeration .1.3.6.1.4.1.18.3.5.9.4.8.1.15 |
wfX25QllcAddrMapGenXidSimulate receiving an XID command from the QLLC device.
This object should be enabled when an PU 2.0 QLLC
device is connecting thru DLSw to an non-X.25 host.rw Enumeration .1.3.6.1.4.1.18.3.5.9.4.8.1.16 |
wfX25QllcAddrMapNodeIdThe 8 hexadecimal digit Node Identification field of the
simulated XID (see wfX25QllcAddrMapGenXid object). This
field has two sub-fields, ID Block and ID Number. The
first 3 hexadecimal digits are the ID block value and the
last 5 hexadecimal digits are the ID Number value.rwobsolete OCTET STRING .1.3.6.1.4.1.18.3.5.9.4.8.1.17 |
wfX25QllcAddrMapNameA informational name for this QLLC Mapping.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.18.3.5.9.4.8.1.18 |