Wellfleet-FRSW-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for Wellfleet-FRSW-MIB.
458
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
458 total| Object Name |
|---|
RFC1155-SMIThe Parameters for the Data Link Connection
Management Interface corresponding to any
interface. Incorporates the Error table. SEQUENCE OF WfFrSwDlcmiEntry .1.3.6.1.4.1.18.3.5.9.6.1 |
wfFrSwCctTableFrame Relay Circuit table gives information
about a virtual circuit.obsolete SEQUENCE OF WfFrSwCctEntry .1.3.6.1.4.1.18.3.5.9.6.2 |
wfFrSwCctEntryAn entry in the Frame Relay (Virtual) Circuit table.obsolete WfFrSwCctEntry .1.3.6.1.4.1.18.3.5.9.6.2.1 |
wfFrSwCctDeleteIndication to delete this frame relay interface.rwobsolete Enumeration .1.3.6.1.4.1.18.3.5.9.6.2.1.1 |
wfFrSwCctNumberInstance identifier; the circuit number of this interface.roobsolete INTEGER .1.3.6.1.4.1.18.3.5.9.6.2.1.2 |
wfFrSwCctDlciInstance identifier; this indicates the virtual
circuit identifierroobsolete Enumeration .1.3.6.1.4.1.18.3.5.9.6.2.1.3 |
wfFrSwCctStateIndicates whether the particular virtual circuit is
operational.roobsolete Enumeration .1.3.6.1.4.1.18.3.5.9.6.2.1.4 |
wfFrSwCctMulticastIndicates whether this dlci is used for multicast
or single destination.rwobsolete Enumeration .1.3.6.1.4.1.18.3.5.9.6.2.1.5 |
wfFrSwCctInBcIndicates the Incoming Committed Burst bits
for this virtual circuit.roobsolete INTEGER .1.3.6.1.4.1.18.3.5.9.6.2.1.6 |
wfFrSwCctOutBcIndicates the Outgoing Committed Burst bits
for this virtual circuit.roobsolete INTEGER .1.3.6.1.4.1.18.3.5.9.6.2.1.7 |
wfFrSwCctInBeIndicates the Incoming Excess Burst bits
for this virtual circuit.rwobsolete INTEGER .1.3.6.1.4.1.18.3.5.9.6.2.1.8 |
wfFrSwCctOutBeIndicates the Outgoing Excess Burst bits
for this virtual circuit.rwobsolete INTEGER .1.3.6.1.4.1.18.3.5.9.6.2.1.9 |
wfFrSwCctInThroughputIndicates the incoming throughput in bits/sec for this virtual circuit.rwobsolete INTEGER .1.3.6.1.4.1.18.3.5.9.6.2.1.10 |
wfFrSwCctOutThroughputIndicates the outgoing throughput in bits/sec for this virtual circuit.rwobsolete INTEGER .1.3.6.1.4.1.18.3.5.9.6.2.1.11 |
wfFrSwCctCreationTimeIndicates the value of sysUpTime when the VC
was created.roobsolete TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.18.3.5.9.6.2.1.12 |
wfFrSwCctLastTimeChangeIndicates the value of sysUpTime when last there was a
change in VC state.roobsolete TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.18.3.5.9.6.2.1.13 |
wfFrSwCctLocalSentNonDEFramesIndicates the number of frames without the DE bit sent on this
virtual circuit over the local interface.roobsolete Counter .1.3.6.1.4.1.18.3.5.9.6.2.1.14 |
wfFrSwCctLocalSentNonDEOctetsIndicates the number of octets without DE bit sent on this
virtual circuit over the local interface.roobsolete Counter .1.3.6.1.4.1.18.3.5.9.6.2.1.15 |
wfFrSwCctLocalSentDEFramesIndicates the number of frames with DE bit set sent on this virtual
circuit over the local interface.roobsolete Counter .1.3.6.1.4.1.18.3.5.9.6.2.1.16 |
wfFrSwCctLocalSentDEOctetsIndicates the number of octets with DE bit set sent on this
virtual circuit over the local interface.roobsolete Counter .1.3.6.1.4.1.18.3.5.9.6.2.1.17 |
wfFrSwCctLocalSetFECNFramesIndicates the number of frames sent to the local
interface on which this switch set the FECN bit .roobsolete Counter .1.3.6.1.4.1.18.3.5.9.6.2.1.18 |
wfFrSwCctLocalSetFECNOctetsIndicates the number of octets in frames sent to the
local interface on which this switch set the FECN bit.roobsolete Counter .1.3.6.1.4.1.18.3.5.9.6.2.1.19 |
wfFrSwCctLocalSetBECNFramesIndicates the number of frames sent to the local
interface on which this switch set the BECN bit.roobsolete Counter .1.3.6.1.4.1.18.3.5.9.6.2.1.20 |
wfFrSwCctLocalSetBECNOctetsIndicates the number of octets in frames sent to the
local interface on which this switch set the BECN bit.roobsolete Counter .1.3.6.1.4.1.18.3.5.9.6.2.1.21 |
wfFrSwCctLocalSetDEFramesIndicates the number of frames sent to the local
interface on which this switch set the DE bit.roobsolete Counter .1.3.6.1.4.1.18.3.5.9.6.2.1.22 |
wfFrSwCctLocalSetDEOctetsIndicates the number of octets in frames sent to the
local interface on which this switch set the DE bit.roobsolete Counter .1.3.6.1.4.1.18.3.5.9.6.2.1.23 |
wfFrSwCctLocalDropNonDEFramesIndicates the number of frames received over the local
interface which were discarded, excluding any frames
with the DE bit set.roobsolete Counter .1.3.6.1.4.1.18.3.5.9.6.2.1.24 |
wfFrSwCctLocalDropNonDEOctetsIndicates the number of octets in frames received over
the local interface which were discarded, excluding any
frames with the DE bit set.roobsolete Counter .1.3.6.1.4.1.18.3.5.9.6.2.1.25 |
wfFrSwCctLocalDropDEFramesIndicates the number of frames received over the local
interface, having the DE bit set, which were discarded.roobsolete Counter .1.3.6.1.4.1.18.3.5.9.6.2.1.26 |
wfFrSwCctLocalDropDEOctetsIndicates the number of octets in frames received over
the local interface, having the DE bit set, which
were discarded.roobsolete Counter .1.3.6.1.4.1.18.3.5.9.6.2.1.27 |
wfFrSwCctInactiveVCDropFramesIndicates how many frames were discarded because the
virtual circuit was inactive.roobsolete Counter .1.3.6.1.4.1.18.3.5.9.6.2.1.28 |
wfFrSwCctInactiveVCDropOctetsIndicates how many Octets were discarded because the
virtual circuit was inactive.roobsolete Counter .1.3.6.1.4.1.18.3.5.9.6.2.1.29 |
wfFrSwCctLocalRecvNonDEFramesIndicates the number of frames received on this
virtual circuit over the local interface.roobsolete Counter .1.3.6.1.4.1.18.3.5.9.6.2.1.30 |
wfFrSwCctLocalRecvNonDEOctetsIndicates the number of octets received on
this virtual circuit over the local interface.roobsolete Counter .1.3.6.1.4.1.18.3.5.9.6.2.1.31 |
wfFrSwCctLocalRecvDEFramesIndicates the number of frames received over the
local interface with the DE bit set.roobsolete Counter .1.3.6.1.4.1.18.3.5.9.6.2.1.32 |
wfFrSwCctLocalRecvDEOctetsIndicates the number of octets in frames received
over the local interface with the DE bit set.roobsolete Counter .1.3.6.1.4.1.18.3.5.9.6.2.1.33 |
wfFrSwCctLocalRecvFECNFramesIndicates the number of frames received over the
local interface with the FECN bit set.roobsolete Counter .1.3.6.1.4.1.18.3.5.9.6.2.1.34 |
wfFrSwCctLocalRecvFECNOctetsIndicates the number of octets in frames received
over the local interface with the FECN bit set.roobsolete Counter .1.3.6.1.4.1.18.3.5.9.6.2.1.35 |
wfFrSwCctLocalRecvBECNFramesIndicates the number of frames received over the
local interface with the BECN bit set.roobsolete Counter .1.3.6.1.4.1.18.3.5.9.6.2.1.36 |
wfFrSwCctLocalRecvBECNOctetsIndicates the number of octets in frames received
over the local interface with the BECN bit set.roobsolete Counter .1.3.6.1.4.1.18.3.5.9.6.2.1.37 |
wfFrSwCctLocalRecentNonDEOctetsIndicates the number of octets received over the local
interface during the most recent sampling period.roobsolete Counter .1.3.6.1.4.1.18.3.5.9.6.2.1.38 |
wfFrSwCctRemoteSentNonDEFramesIndicates the number of Non DE set frames sent over the remote interface.roobsolete Counter .1.3.6.1.4.1.18.3.5.9.6.2.1.39 |
wfFrSwCctRemoteSentNonDEOctetsIndicates the number of Non DE set octets sent over the remote interface.roobsolete Counter .1.3.6.1.4.1.18.3.5.9.6.2.1.40 |
wfFrSwCctRemoteSentDEFramesIndicates the number of DE set frames sent over the remote interface.roobsolete Counter .1.3.6.1.4.1.18.3.5.9.6.2.1.41 |
wfFrSwCctRemoteSentDEOctetsIndicates the number of DE set octets sent over the remote interface.roobsolete Counter .1.3.6.1.4.1.18.3.5.9.6.2.1.42 |
wfFrSwCctRemoteSetFECNFramesIndicates the number of frames sent to the remote
interface on which this switch set the FECN bit.roobsolete Counter .1.3.6.1.4.1.18.3.5.9.6.2.1.43 |
wfFrSwCctRemoteSetFECNOctetsIndicates the number of octets in frames sent to the remote
interface that on which this switch set the FECN bit.roobsolete Counter .1.3.6.1.4.1.18.3.5.9.6.2.1.44 |
wfFrSwCctRemoteSetBECNFramesIndicates the number of frames sent to the remote
interface on which this switch set the BECN bit.roobsolete Counter .1.3.6.1.4.1.18.3.5.9.6.2.1.45 |
wfFrSwCctRemoteSetBECNOctetsIndicates the number of octets in frames sent to the
remote interface on which this switch set the BECN bit.roobsolete Counter .1.3.6.1.4.1.18.3.5.9.6.2.1.46 |
wfFrSwCctRemoteDropNonDEFramesIndicates the number of frames received over the
remote interface which were discarded, excluding
any frames with the DE bit set.roobsolete Counter .1.3.6.1.4.1.18.3.5.9.6.2.1.47 |
wfFrSwCctRemoteDropNonDEOctetsIndicates the number of octets in frames received
over the remote interface which were discarded,
excluding any frames with the DE bit set.roobsolete Counter .1.3.6.1.4.1.18.3.5.9.6.2.1.48 |
wfFrSwCctRemoteDropDEFramesIndicates the number of frames received over
the remote interface, having the DE bit set,
which were discarded.roobsolete Counter .1.3.6.1.4.1.18.3.5.9.6.2.1.49 |
wfFrSwCctRemoteDropDEOctetsIndicates the number of octets in frames received over
the remote interface, having the DE bit set,
which were discarded.roobsolete Counter .1.3.6.1.4.1.18.3.5.9.6.2.1.50 |
wfFrSwCctRemoteRecvNonDEFramesIndicates the number of frames received on this virtual
circuit over the remote interface.roobsolete Counter .1.3.6.1.4.1.18.3.5.9.6.2.1.51 |
wfFrSwCctRemoteRecvNonDEOctetsIndicates the number of octets received on this
virtual circuit over the remote interface.roobsolete Counter .1.3.6.1.4.1.18.3.5.9.6.2.1.52 |
wfFrSwCctRemoteRecvDEFramesIndicates the number of frames received over the
remote interface with the DE bit set.roobsolete Counter .1.3.6.1.4.1.18.3.5.9.6.2.1.53 |
wfFrSwCctRemoteRecvDEOctetsIndicates the number of octets in frames received over
the remote interface with the DE bit set.roobsolete Counter .1.3.6.1.4.1.18.3.5.9.6.2.1.54 |
wfFrSwCctRemoteRecvFECNFramesIndicates the number of frames received over the
remote interface with the FECN bit set.roobsolete Counter .1.3.6.1.4.1.18.3.5.9.6.2.1.55 |
wfFrSwCctRemoteRecvFECNOctetsIndicates the number of octets in frames received over
the remote interface with the FECN bit set.roobsolete Counter .1.3.6.1.4.1.18.3.5.9.6.2.1.56 |
wfFrSwCctRemoteRecvBECNFramesIndicates the number of frames received over the
remote interface with the BECN bit set.roobsolete Counter .1.3.6.1.4.1.18.3.5.9.6.2.1.57 |
wfFrSwCctRemoteRecvBECNOctetsIndicates the number of octets in frames received over
the remote interface with the BECN bit set.roobsolete Counter .1.3.6.1.4.1.18.3.5.9.6.2.1.58 |
wfFrSwCctLocalBecnStateIndicates the local BECN stateroobsolete INTEGER .1.3.6.1.4.1.18.3.5.9.6.2.1.59 |
wfFrSwCctRemoteBecnStateIndicates the remote BECN stateroobsolete INTEGER .1.3.6.1.4.1.18.3.5.9.6.2.1.60 |
wfFrSwCctLocalOrRemoteConnectionIndicates whether this connection is Local to Local Connection
or Local to Remote connection.roobsolete Enumeration .1.3.6.1.4.1.18.3.5.9.6.2.1.61 |
wfFrSwCctInBcOctetsIndicates the Incoming Committed Burst in octets
for this virtual circuit.roobsolete INTEGER .1.3.6.1.4.1.18.3.5.9.6.2.1.62 |
wfFrSwCctStateSetUser access for setting the state of a virtual circuitrwobsolete Enumeration .1.3.6.1.4.1.18.3.5.9.6.2.1.63 |
wfFrSwCctReportedStatusRecord keeping for circuit statusroobsolete Enumeration .1.3.6.1.4.1.18.3.5.9.6.2.1.64 |
wfFrSwCctReceivedStatusState of a virtual circuit as reported by the network at an NNIroobsolete Enumeration .1.3.6.1.4.1.18.3.5.9.6.2.1.65 |
wfFrSwCctCrossNetStatusState of a virtual circuit as reported by the other end of the network
under bidirectional signalling.roobsolete Enumeration .1.3.6.1.4.1.18.3.5.9.6.2.1.66 |
wfFrSwCctXNetSentWhether we have sent a cross net status message for this VC yet.roobsolete Enumeration .1.3.6.1.4.1.18.3.5.9.6.2.1.67 |
wfFrSwCctXNetReceivedWhether we have received a cross net status message for this VC during
the current polling interval.roobsolete Enumeration .1.3.6.1.4.1.18.3.5.9.6.2.1.68 |
wfFrSwCctXNetErrorsThis is the count of the consecutive errors (usually timeouts) against
this VC in cross-network heartbeat pollingroobsolete Counter .1.3.6.1.4.1.18.3.5.9.6.2.1.69 |
wfFrSwTupleTableThe Parameters for the Tuple table, identifying
the endpoints of virtual circuits as pairs of IP
addresses and DLCI.obsolete SEQUENCE OF WfFrSwTupleEntry .1.3.6.1.4.1.18.3.5.9.6.3 |
wfFrSwTupleEntryThe parameters for a particular Tuple.obsolete WfFrSwTupleEntry .1.3.6.1.4.1.18.3.5.9.6.3.1 |
wfFrSwTupleDeleteIndication to delete this tuple.rwobsolete Enumeration .1.3.6.1.4.1.18.3.5.9.6.3.1.1 |
wfFrSwTupleIpAddrAInstance indentifier; indicates the IP address
associated with endpoint 'A' of a virtual circuit.roobsolete IpAddress .1.3.6.1.4.1.18.3.5.9.6.3.1.2 |
wfFrSwTupleDlciAInstance identfier; indicates the DLCI associated
with endpoint 'A' of a virtual circuit.roobsolete INTEGER .1.3.6.1.4.1.18.3.5.9.6.3.1.3 |
wfFrSwTupleIpAddrBInstance identfier; indicates the IP address
associated with endpoint 'B' of a virtual circuit.roobsolete IpAddress .1.3.6.1.4.1.18.3.5.9.6.3.1.4 |
wfFrSwTupleDlciBInstance identifier; Indicates the DLCI associated
with endpoint 'B' of a virtual circuit.roobsolete INTEGER .1.3.6.1.4.1.18.3.5.9.6.3.1.5 |
wfFrSwMcastTableThe list of multicast addresses SEQUENCE OF WfFrSwMcastEntry .1.3.6.1.4.1.18.3.5.9.6.4 |
wfFrSwMcastEntryThe parameters for a particular Multicast address. WfFrSwMcastEntry .1.3.6.1.4.1.18.3.5.9.6.4.1 |
wfFrSwMcastDeleteIndication to delete this multicast instance.rw Enumeration .1.3.6.1.4.1.18.3.5.9.6.4.1.1 |
wfFrSwMcastIndexIndex of this multicast DLCI instancero INTEGER .1.3.6.1.4.1.18.3.5.9.6.4.1.2 |
wfFrSwMcastIpAddrIP address of the interface in which this multicast DLCI is defined.rw IpAddress .1.3.6.1.4.1.18.3.5.9.6.4.1.3 |
wfFrSwMcastDlciIdentifies the multicast DLCI with which the IndividualDlci is associated.rw INTEGER .1.3.6.1.4.1.18.3.5.9.6.4.1.4 |
wfFrSwMcastIndividualDlciIndicates the DLCI associated with the above multicast DLCI.rw INTEGER .1.3.6.1.4.1.18.3.5.9.6.4.1.5 |
wfFrSwUsage OBJECT IDENTIFIER .1.3.6.1.4.1.18.3.5.9.6.5 |
wfFrSwUsageEnableEnable/Disable FRSW billing.rw Enumeration .1.3.6.1.4.1.18.3.5.9.6.5.1 |
wfFrSwUsageVolumeIndicates the file system volume number to which the
billing usage data files will be written. The volume
number corresponds to the slot number on which the
volume resides.
Note: Value 0 has the special meaning that no
'Store' and 'Flush' operations will take
place. This translates to no Billing data
will be written to the local file system.
'Update' operations will still be performed on
each local slot. Full Billing statistics
will still be available in the wfFrSwUsageTable
MIB.rw INTEGER .1.3.6.1.4.1.18.3.5.9.6.5.2 |
wfFrSwUsageVolumeBackupIndicates the backup volume if wfFrSwUsageVolume
becomes inoperative.
Note: This feature is not implemented in this release.rw INTEGER .1.3.6.1.4.1.18.3.5.9.6.5.3 |
wfFrSwUsageDirectoryThe name of the directory where the billing usage data
files are stored.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.18.3.5.9.6.5.4 |
wfFrSwUsageFilePrefixThe base name of billing usage data files.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.18.3.5.9.6.5.5 |
wfFrSwUsageTimerIntervalThis number determines the timer interval (number
of seconds) unit for the Billing process to perform
its various timer driven tasks. i.e. updating billing
usage data, writing billing usage data to file system
and file system management activities.rw INTEGER .1.3.6.1.4.1.18.3.5.9.6.5.6 |
wfFrSwUsageUpdateIntervalThis number specifies the interval (number of minutes)
for the Billing process to collect and update billing
usage data in the wfFrSwUsage MIB. Note: When converted to seconds, this must be a multiple
of wfFrSwUsageTimerInterval.rw INTEGER .1.3.6.1.4.1.18.3.5.9.6.5.7 |
wfFrSwUsageStoreIntervalThis number specifies the interval (number of minutes)
for the Billing process to write billing usage data on
to the file system from the wfFrSwUsage MIB.
Note: When converted to seconds, this must be a multiple
of wfFrSwUsageTimerInterval.rw INTEGER .1.3.6.1.4.1.18.3.5.9.6.5.8 |
wfFrSwUsageFlushIntervalThis number specifies the interval (number of minutes)
for the Billing process to write billing usage data on
to the file system from the wfFrSwUsage MIB follow
by zeroing the wfFrSwUsage MIB.
Note: When converted to seconds, this must be a multiple of
wfFrSwUsageTimerInterval.rw INTEGER .1.3.6.1.4.1.18.3.5.9.6.5.9 |
wfFrSwUsageCleanupIntervalThis is the interval (number of minutes) for the Billing
process to check and delete old billing usage data files.
Note: When converted to seconds, this must be a multilple
of wfFrSwUsageTimerInterval.rw INTEGER .1.3.6.1.4.1.18.3.5.9.6.5.10 |
wfFrSwUsageLocalTimeZoneIndicates local time zone of the switchro INTEGER .1.3.6.1.4.1.18.3.5.9.6.5.11 |
wfFrSwUsageUpdateTimeStampTime stamp of last wfFrSwUsageUpdateInterval timer
expiration or the starting time of the current
wfFrSwUsageUpdateInterval. This value is number
of seconds since midnight Jan 1, 1976 (GMT).ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.18.3.5.9.6.5.12 |
wfFrSwUsageStoreTimeStampTime stamp of last wfFrSwUsageStoreInterval
timer expiration or the starting time of the current
wfFrSwUsageStoreInterval. This value is number
of seconds since midnight Jan. 1, 1976 (GMT).ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.18.3.5.9.6.5.13 |
wfFrSwUsageFlushTimeStampTime stamp of last wfFrSwUsageFlushInterval
timer expiration or the starting time of the current
wfFrSwUsageFlushInterval. This value is
number of seconds since midnight Jan. 1, 1976 (GMT).ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.18.3.5.9.6.5.14 |
wfFrSwUsageCleanupTimeStampTime stamp of last wfFrSwUsageCleanupInterval
timer expiration or the starting time of the current
wfFrSwUsageCleanupInterval. This value is number
of seconds since midnight Jan. 1, 1976 (GMT).ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.18.3.5.9.6.5.15 |
wfFrSwUsageUpdateDataSetting this attribute to a non-zero value will cause
an immediate updating of the billing usage data.
Once activated, this attribute should be reset to zero
to allow subsequent activations.rw INTEGER .1.3.6.1.4.1.18.3.5.9.6.5.16 |
wfFrSwUsageStoreDataSetting this attribute to a non-zero value will cause
an immediate updating and writing of the billing
usage data. Once activated, this attribute should
be reset to zero to allow subsequent activations.rw INTEGER .1.3.6.1.4.1.18.3.5.9.6.5.17 |
wfFrSwUsageFlushDataSetting this attribute to a non-zero value will cause
an immediate updating and writing of the billing usage
data and followed by zeroing the wfFrSwBillingUsage
MIB. Once activated, this attribute should be reset
to zero to allow subsequent activations.rw INTEGER .1.3.6.1.4.1.18.3.5.9.6.5.18 |
wfFrSwUsageFileCleanupSetting this attribute to a non-zero value will cause
an immediate checking and deleting old billing usage
data files. Once activated, this attribute should
be reset to zero to allow subsequent activations.rw INTEGER .1.3.6.1.4.1.18.3.5.9.6.5.19 |
wfFrSwUsageStatecurrent state FRSW billing.ro Enumeration .1.3.6.1.4.1.18.3.5.9.6.5.20 |
wfFrSwUsageCurVolumecurrent file system volume number used. This
number is the same as wfFrSwUsageVolume except
when the user sets wfFrSwUsageVolume to an
invalid number.ro INTEGER .1.3.6.1.4.1.18.3.5.9.6.5.21 |
wfFrSwUsageCurVolumeBackupcurent backup file system volume number used. This
number is the same as wfFrSwUsageVolumeBackUp except
when the user sets wfFrSwUsageVolume to an
invalid number.
Note: This feature is not implemented in this release.ro INTEGER .1.3.6.1.4.1.18.3.5.9.6.5.22 |
wfFrSwUsageCurDirectorycurrent directory name used. This number is the
same as wfFrSwUsageDirectory except when the user
sets wfFrSwUsageDirectory to an invalid name.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.18.3.5.9.6.5.23 |
wfFrSwUsageCurFilePrefixcurrent base file name used. This number is the
same as wfFrSwUsageFilePrefix except when the user
sets wfFrSwUsageFilePrefix to an invalid name.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.18.3.5.9.6.5.24 |
wfFrSwUsageCurTimerIntervalcurrent timer interval number used. This number is
the same as wfFrSwUsageTimerInterval except when the
user sets wfFrSwUsageTimerInterval to an invalid value.ro INTEGER .1.3.6.1.4.1.18.3.5.9.6.5.25 |
wfFrSwUsageCurUpdateIntervalcurrent update interval number used. This number is
the same as wfFrSwUsageUpdateInterval except when the
user sets wfFrSwUsageUpdateInterval to an invalid value.ro INTEGER .1.3.6.1.4.1.18.3.5.9.6.5.26 |
wfFrSwUsageCurStoreIntervalcurrent store timer interval number used. This
number is the same as wfFrSwUsageStoreInterval
except when the user sets wfFrSwUsageStoreInterval
to an invalid value.ro INTEGER .1.3.6.1.4.1.18.3.5.9.6.5.27 |
wfFrSwUsageCurFlushIntervalcurrent flush timer interval number used. This
number is the same as wfFrSwUsageFlushInterval
except when the user sets wfFrSwUsageFlushInterval
to an invalid value.ro INTEGER .1.3.6.1.4.1.18.3.5.9.6.5.28 |
wfFrSwUsageCurCleanupIntervalcurrent file cleanup timer interval number used. This
number is the same as wfFrSwUsageCleanupInterval
except when the user sets wfFrSwUsageCleanupInterval
to an invalid value.ro INTEGER .1.3.6.1.4.1.18.3.5.9.6.5.29 |
wfFrSwUsageDebugEnable/Disable printing of debug edl (trap)
messages.
NOTE: Do not enable this attribute in operational enviornment
as it will likely flood the logging facility. This
attribute is reserved for specialized debugging in a
controlled lab enviornment.rw Enumeration .1.3.6.1.4.1.18.3.5.9.6.5.30 |
wfFrSwUsageCurDebugcurrent debug value used. This value is the
same as wfFrSwUsageDebug except when the user
sets wfFrSwUsageDeubg to an invalid value.ro Enumeration .1.3.6.1.4.1.18.3.5.9.6.5.31 |
wfFrSwUsageSwitchIdswitch id used in the billing usage data file.ro INTEGER .1.3.6.1.4.1.18.3.5.9.6.5.32 |
wfFrSwUsageNumEntriesnumber of entries in wfFrSwUsageTablero INTEGER .1.3.6.1.4.1.18.3.5.9.6.5.33 |
wfFrSwSvcUsageEnableEnable/Disable FRSW SVC billing.rw Enumeration .1.3.6.1.4.1.18.3.5.9.6.5.34 |
wfFrSwSvcUsageInterimRecordEnableEnable/Disable Writing FRSW SVC billing record
while SVC connection is still up.rw Enumeration .1.3.6.1.4.1.18.3.5.9.6.5.35 |
wfFrSwSvcUsageVolumeIndicates the file system volume number to which the
SVC billing usage data files will be written. The volume
number corresponds to the slot number on which the
volume resides.
Note: Value 0 has the special meaning that no
'Store' and 'Flush' operations will take
place. This translates to no Billing data
will be written to the local file system.
'Update' operations will still be performed on
each local slot. Full Billing statistics
will still be available in the wfFrSwUsageTable
MIB.rw INTEGER .1.3.6.1.4.1.18.3.5.9.6.5.36 |
wfFrSwSvcUsageDirectoryThe name of the directory where the SVC billing usage data
files are stored.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.18.3.5.9.6.5.37 |
wfFrSwSvcUsageFilePrefixThe base name of SVC billing usage data files.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.18.3.5.9.6.5.38 |
wfFrSwSvcUsageUpdateIntervalThis number specifies the interval (number of minutes)
for the SVC Billing process to collect and update billing
usage data in the wfFrSwUsage MIB. Note: When converted
to seconds, this must be a multiple of
wfFrSwUsageTimerInterval.rw INTEGER .1.3.6.1.4.1.18.3.5.9.6.5.39 |
wfFrSwSvcUsageStoreIntervalThis number specifies the interval (number of minutes)
for the SVC Billing process to write billing usage data on
to the file system from the wfFrSwUsage MIB.
Note: When converted to seconds, this must be a multiple
of wfFrSwUsageTimerInterval.rw INTEGER .1.3.6.1.4.1.18.3.5.9.6.5.40 |
wfFrSwSvcUsageFlushIntervalThis number specifies the interval (number of minutes)
for the SVC Billing process to write billing usage data on
to the file system from the wfFrSwUsage MIB follow
by zeroing the wfFrSwUsage MIB.
Note: When converted to seconds, this must be a multiple of
wfFrSwUsageTimerInterval.rw INTEGER .1.3.6.1.4.1.18.3.5.9.6.5.41 |
wfFrSwSvcUsageCleanupIntervalThis is the interval (number of minutes) for the SVC Billing
process to check and delete old billing usage data files.
Note: When converted to seconds, this must be a multilple
of wfFrSwUsageTimerInterval.rw INTEGER .1.3.6.1.4.1.18.3.5.9.6.5.42 |
wfFrSwSvcUsageUpdateTimeStampTime stamp of last wfFrSwSvcUsageUpdateInterval timer
expiration or the starting time of the current
wfFrSwSvcUsageUpdateInterval. This value is number
of seconds since midnight Jan 1, 1976 (GMT).ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.18.3.5.9.6.5.43 |
wfFrSwSvcUsageStoreTimeStampTime stamp of last wfFrSwSvcUsageStoreInterval
timer expiration or the starting time of the current
wfFrSwSvcUsageStoreInterval. This value is number
of seconds since midnight Jan. 1, 1976 (GMT).ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.18.3.5.9.6.5.44 |
wfFrSwSvcUsageFlushTimeStampTime stamp of last wfFrSwSvcUsageFlushInterval
timer expiration or the starting time of the current
wfFrSwSvcUsageFlushInterval. This value is
number of seconds since midnight Jan. 1, 1976 (GMT).ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.18.3.5.9.6.5.45 |
wfFrSwSvcUsageCleanupTimeStampTime stamp of last wfFrSwSvcUsageCleanupInterval
timer expiration or the starting time of the current
wfFrSwSvcUsageCleanupInterval. This value is number
of seconds since midnight Jan. 1, 1976 (GMT).ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.18.3.5.9.6.5.46 |
wfFrSwSvcUsageUpdateDataSetting this attribute to a non-zero value will cause
an immediate updating of the SVC billing usage data.
Once activated, this attribute should be reset to zero
to allow subsequent activations.rw INTEGER .1.3.6.1.4.1.18.3.5.9.6.5.47 |
wfFrSwSvcUsageStoreDataSetting this attribute to a non-zero value will cause
an immediate updating and writing of the SVC billing
usage data. Once activated, this attribute should
be reset to zero to allow subsequent activations.rw INTEGER .1.3.6.1.4.1.18.3.5.9.6.5.48 |
wfFrSwSvcUsageFlushDataSetting this attribute to a non-zero value will cause
an immediate updating and writing of the SVC billing usage
data and followed by zeroing the wfFrSwBillingUsage
MIB. Once activated, this attribute should be reset
to zero to allow subsequent activations.rw INTEGER .1.3.6.1.4.1.18.3.5.9.6.5.49 |
wfFrSwSvcUsageFileCleanupSetting this attribute to a non-zero value will cause
an immediate checking and deleting old SVC billing usage
data files. Once activated, this attribute should
be reset to zero to allow subsequent activations.rw INTEGER .1.3.6.1.4.1.18.3.5.9.6.5.50 |
wfFrSwSvcUsageStatecurrent state FRSW SVC billing.ro Enumeration .1.3.6.1.4.1.18.3.5.9.6.5.51 |
wfFrSwSvcUsageCurVolumecurrent file system volume number used for SVC Billing.
This number is the same as wfFrSwSvcUsageVolume except
when the user sets wfFrSwSvcUsageVolume to an
invalid number.ro INTEGER .1.3.6.1.4.1.18.3.5.9.6.5.52 |
wfFrSwSvcUsageCurDirectorycurrent directory name used for SVC Billing. This number
is the same as wfFrSwSvcUsageDirectory except when the user
sets wfFrSwSvcUsageDirectory to an invalid name.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.18.3.5.9.6.5.53 |
wfFrSwSvcUsageCurFilePrefixcurrent base file name used for SVC Billing. This name
is the same as wfFrSwSvcUsageFilePrefix except when the user
sets wfFrSwSvcUsageFilePrefix to an invalid name.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.18.3.5.9.6.5.54 |
wfFrSwSvcUsageCurUpdateIntervalcurrent update interval number used. This number is
the same as wfFrSwSvcUsageUpdateInterval except when the
user sets wfFrSwSvcUsageUpdateInterval to an invalid value.ro INTEGER .1.3.6.1.4.1.18.3.5.9.6.5.55 |
wfFrSwSvcUsageCurStoreIntervalcurrent store timer interval number used. This
number is the same as wfFrSwSvcUsageStoreInterval
except when the user sets wfFrSwSvcUsageStoreInterval
to an invalid value.ro INTEGER .1.3.6.1.4.1.18.3.5.9.6.5.56 |
wfFrSwSvcUsageCurFlushIntervalcurrent flush timer interval number used. This
number is the same as wfFrSwSvcUsageFlushInterval
except when the user sets wfFrSwSvcUsageFlushInterval
to an invalid value.ro INTEGER .1.3.6.1.4.1.18.3.5.9.6.5.57 |
wfFrSwSvcUsageCurCleanupIntervalcurrent file cleanup timer interval number used. This
number is the same as wfFrSwSvcUsageCleanupInterval
except when the user sets wfFrSwSvcUsageCleanupInterval
to an invalid value.ro INTEGER .1.3.6.1.4.1.18.3.5.9.6.5.58 |
wfFrSwSvcUsageNumEntriesnumber of entries in wfFrSwSvcUsageTablero INTEGER .1.3.6.1.4.1.18.3.5.9.6.5.59 |
wfFrSwSvcUsageVersionIdThe Software Version ID field is a two byte, right justified,
binary formated value that identifies the particular version
number of the software release. High nibble of byte 1 represents
the major version number. Low nibble of byte 1 represents the
release number. Byte 2 represents the integration number.ro INTEGER .1.3.6.1.4.1.18.3.5.9.6.5.60 |
wfFrSwUsageSwitchNameThe Switch name is a 6-bytes, right justified with leading
blanks as necessary. It can be combination of letters, numbers
and blanks. This ID identifies the particular networks
equipment for SVC billing usage data process.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.18.3.5.9.6.5.61 |
wfFrSwPvcUsageFileLayoutPVC usage file layout versionro INTEGER .1.3.6.1.4.1.18.3.5.9.6.5.62 |
wfFrSwSvcUsageFileLayoutSVC usage file layout versionro INTEGER .1.3.6.1.4.1.18.3.5.9.6.5.63 |
wfFrSwUsageTableThe Billing usage table.obsolete SEQUENCE OF WfFrSwUsageEntry .1.3.6.1.4.1.18.3.5.9.6.6 |
wfFrSwUsageEntryThe parameters for Billing Usage.obsolete WfFrSwUsageEntry .1.3.6.1.4.1.18.3.5.9.6.6.1 |
wfFrSwUsageDeleteIndicates status of this entry. FRSW_USAGE_CREATED
is the normal case. FRSW_USAGE_DELETED means the
corresponding tuple and vc instances were deleted
some time during this collection interval. This
billing instance will be deleted at the end of
the next wfFrSwUsageFlush period after this
billing record is written out to the file system.roobsolete Enumeration .1.3.6.1.4.1.18.3.5.9.6.6.1.1 |
wfFrSwUsageCircuitNumberInstance identifier; the circuit number of this
interface.roobsolete INTEGER .1.3.6.1.4.1.18.3.5.9.6.6.1.2 |
wfFrSwUsageDlciInstance identifier; this indicates which virtual
circuit.roobsolete Enumeration .1.3.6.1.4.1.18.3.5.9.6.6.1.3 |
wfFrSwUsageIPAddress(Local) IP address corresponding to
wfFrSwUsageCircuitNumber of this virtual circuit.roobsolete IpAddress .1.3.6.1.4.1.18.3.5.9.6.6.1.4 |
wfFrSwUsageStartTimeStampHighTime stamp of the starting time (the high 32 bits)
of last billing usage interval. This value is the
number of 1/100th seconds since midnight Jan 1, 1976 (GMT).roobsolete INTEGER .1.3.6.1.4.1.18.3.5.9.6.6.1.5 |
wfFrSwUsageStartTimeStampLowTime stamp of the starting time (the low 32 bits)
of last billing usage interval. This value is the
number of 1/100th seconds since midnight Jan 1, 1976 (GMT).roobsolete INTEGER .1.3.6.1.4.1.18.3.5.9.6.6.1.6 |
wfFrSwUsageEndTimeStampHighTime stamp of the ending time (the high 32 bits)
of last billing usage interval. This value is the
number of 1/100th seconds since midnight Jan 1, 1976 (GMT).roobsolete INTEGER .1.3.6.1.4.1.18.3.5.9.6.6.1.7 |
wfFrSwUsageEndTimeStampLowTime stamp of the ending time (the low 32 bits)
of last billing usage interval. This value is the
number of 1/100th seconds since midnight Jan 1, 1976 (GMT).roobsolete INTEGER .1.3.6.1.4.1.18.3.5.9.6.6.1.8 |
wfFrSwUsageSentNonDEFramesHighNumber (the high 32 bits) of local frames sent
from this virtual circuit between
wfFrSwUsageStartTimeStamp and
wfFrSwUsageEndTimeStamp.roobsolete INTEGER .1.3.6.1.4.1.18.3.5.9.6.6.1.9 |
wfFrSwUsageSentNonDEFramesLowNumber (the low 32 bits) of local frames sent
from this virtual circuit between
wfFrSwUsageStartTimeStamp
and wfFrSwUsageEndTimeStamp.roobsolete INTEGER .1.3.6.1.4.1.18.3.5.9.6.6.1.10 |
wfFrSwUsageSentNonDEOctetsHighNumber (the high 32 bits) of local octets sent from
this virtual circuit between
wfFrSwUsageStartTimeStamp and
wfFrSwUsageEndTimeStamp.roobsolete INTEGER .1.3.6.1.4.1.18.3.5.9.6.6.1.11 |
wfFrSwUsageSentNonDEOctetsLowNumber (the low 32 bits) of local octets sent from
this virtual circuit between
wfFrSwUsageStartTimeStamp and
wfFrSwUsageEndTimeStamp.roobsolete INTEGER .1.3.6.1.4.1.18.3.5.9.6.6.1.12 |
wfFrSwUsageSentDEFramesHighNumber (the high 32 bits) of local frames with DE
bit sent from this virtual circuit between
wfFrSwUsageStartTimeStamp and
wfFrSwUsageEndTimeStamp.roobsolete INTEGER .1.3.6.1.4.1.18.3.5.9.6.6.1.13 |
wfFrSwUsageSentDEFramesLowNumber (the low 32 bits) of local frames with DE
bit sent from this virtual circuit between
wfFrSwUsageStartTimeStamp
and wfFrSwUsageEndTimeStamp.roobsolete INTEGER .1.3.6.1.4.1.18.3.5.9.6.6.1.14 |
wfFrSwUsageSentDEOctetsHighNumber (the high 32 bits) of local octets with
DE bit sent from this virtual circuit between
wfFrSwUsageStartTimeStamp and
wfFrSwUsageEndTimeStamp.roobsolete INTEGER .1.3.6.1.4.1.18.3.5.9.6.6.1.15 |
wfFrSwUsageSentDEOctetsLowNumber (the low 32 bits) of local octets with
DE bit sent from this virtual circuit between
wfFrSwUsageStartTimeStamp and
wfFrSwUsageEndTimeStamp.roobsolete INTEGER .1.3.6.1.4.1.18.3.5.9.6.6.1.16 |
wfFrSwUsageLastNonDEFramesHighThe (high 32 bits) value of
wfFrSwCctLocalSentNonDEFrames value at
wfFrSwUsageEndTimeStamp.
Note: Since wfFrSwCctLocalSentNonDEFrames
is a 32-bit COUNTER, this is really a counter
keeping track of number of times
wfFrSwCctLocalSentNonDEFrames has wrapped
around.roobsolete INTEGER .1.3.6.1.4.1.18.3.5.9.6.6.1.17 |
wfFrSwUsageLastNonDEFramesLowThe (low 32 bits) value of
wfFrSwCctLocalSentNonDEFrames value at
wfFrSwUsageEndTimeStamp.roobsolete INTEGER .1.3.6.1.4.1.18.3.5.9.6.6.1.18 |
wfFrSwUsageLastNonDEOctetsHighThe (high 32 bits) value of
wfFrSwCctLocalSentNonDEOctets value at
wfFrSwUsageEndTimeStamp.
Note: Since wfFrSwCctLocalSentNonDEOctets
is a 32-bit COUNTER, this is really a counter
keeping track of number of times
wfFrSwCctLocalSentNonDEOctets has wrapped around.roobsolete INTEGER .1.3.6.1.4.1.18.3.5.9.6.6.1.19 |
wfFrSwUsageLastNonDEOctetsLowThe (low 32 bits) value of
wfFrSwCctLocalSentNonDEOctets value at
wfFrSwUsageEndTimeStamp.roobsolete INTEGER .1.3.6.1.4.1.18.3.5.9.6.6.1.20 |
wfFrSwUsageLastDEFramesHighThe (high 32 bits) value of
wfFrSwCctLocalSentDEFrames value at
wfFrSwUsageEndTimeStamp.
Note: Since wfFrSwCctLocalSentNonDEFrames
is a 32-bit COUNTER, this is really a counter
keeping track of number of times
wfFrSwCctLocalSentDEFrames has wrapped
around.roobsolete INTEGER .1.3.6.1.4.1.18.3.5.9.6.6.1.21 |
wfFrSwUsageLastDEFramesLowThe (low 32 bits) value of
wfFrSwCctLocalSentDEFrames value at
wfFrSwUsageEndTimeStamp.roobsolete INTEGER .1.3.6.1.4.1.18.3.5.9.6.6.1.22 |
wfFrSwUsageLastDEOctetsHighThe (high 32 bits) value of
wfFrSwCctLocalSentDEOctets value
at wfFrSwUsageEndTimeStamp.
Note: Since wfFrSwCctLocalSentDEOctets
is a 32-bit COUNTER, this is really a counter
keeping track of number of times
wfFrSwCctLocalSentDEOctets has wrapped around.roobsolete INTEGER .1.3.6.1.4.1.18.3.5.9.6.6.1.23 |
wfFrSwUsageLastDEOctetsLowThe (low 32 bits) value of
wfFrSwCctLocalSentDEOctets value
at wfFrSwUsageEndTimeStamp.roobsolete INTEGER .1.3.6.1.4.1.18.3.5.9.6.6.1.24 |
wfFrSwUsageRemoteIPAddressIP address of the other side (remote) of this PVC endpoint.roobsolete IpAddress .1.3.6.1.4.1.18.3.5.9.6.6.1.25 |
wfFrSwUsageRemoteDlciDLCI number of the other side (remote) of this PVC endpoint.roobsolete Enumeration .1.3.6.1.4.1.18.3.5.9.6.6.1.26 |
wfFrSwVcTableFrame Relay Virtual Circuit table gives information
about a virtual circuit. SEQUENCE OF WfFrSwVcEntry .1.3.6.1.4.1.18.3.5.9.6.7 |
wfFrSwVcEntryAn entry in the Frame Relay (Virtual) Circuit table. WfFrSwVcEntry .1.3.6.1.4.1.18.3.5.9.6.7.1 |
wfFrSwVcDeleteIndication to delete this virtual circuit.rw Enumeration .1.3.6.1.4.1.18.3.5.9.6.7.1.1 |
wfFrSwVcCircuitInstance identifier; the circuit number of this interface
(logical port).ro INTEGER .1.3.6.1.4.1.18.3.5.9.6.7.1.2 |
wfFrSwVcDlciInstance identifier; this indicates the virtual
circuit identifierro INTEGER .1.3.6.1.4.1.18.3.5.9.6.7.1.3 |
wfFrSwVcStateIndicates whether the particular virtual circuit is
operational.ro Enumeration .1.3.6.1.4.1.18.3.5.9.6.7.1.4 |
wfFrSwVcStateSetUser access for setting the state of a virtual circuitrw Enumeration .1.3.6.1.4.1.18.3.5.9.6.7.1.5 |
wfFrSwVcMulticastIndicates whether this dlci is used for multicast
or a single destination.rw Enumeration .1.3.6.1.4.1.18.3.5.9.6.7.1.6 |
wfFrSwVcInBeIndicates the maximum number Incoming Excess Burst bits
that are allowed in a configured time interval (T).ro INTEGER .1.3.6.1.4.1.18.3.5.9.6.7.1.7 |
wfFrSwVcOutBeIndicates the Outgoing Excess Burst bits
for this virtual circuit.ro INTEGER .1.3.6.1.4.1.18.3.5.9.6.7.1.8 |
wfFrSwVcInThroughputIndicates the incoming throughput in bits/sec
for this virtual circuit.rw INTEGER .1.3.6.1.4.1.18.3.5.9.6.7.1.9 |
wfFrSwVcOutThroughputIndicates the outgoing throughput in bits/sec
for this virtual circuit.rw INTEGER .1.3.6.1.4.1.18.3.5.9.6.7.1.10 |
wfFrSwVcOutBcIndicates the Outgoing Committed Burst bits
for this virtual circuit.ro INTEGER .1.3.6.1.4.1.18.3.5.9.6.7.1.11 |
wfFrSwVcInBcIndicates the Incoming Committed Burst bits
for this virtual circuit.ro INTEGER .1.3.6.1.4.1.18.3.5.9.6.7.1.12 |
wfFrSwVcInBcOctetsIndicates the Incoming Committed Burst in octets
for this virtual circuit.ro INTEGER .1.3.6.1.4.1.18.3.5.9.6.7.1.13 |
wfFrSwVcBecnStateIndicates the BECN statero INTEGER .1.3.6.1.4.1.18.3.5.9.6.7.1.14 |
wfFrSwVcReportedStatusRecord keeping for circuit statusro Enumeration .1.3.6.1.4.1.18.3.5.9.6.7.1.15 |
wfFrSwVcReceivedStatusState of a virtual circuit as reported by the network at an NNIro Enumeration .1.3.6.1.4.1.18.3.5.9.6.7.1.16 |
wfFrSwVcCrossNetStatusState of a virtual circuit as reported by
the other end of the network under
bidirectional signalling.ro Enumeration .1.3.6.1.4.1.18.3.5.9.6.7.1.17 |
wfFrSwVcXNetSentWhether we have sent a cross net status
message for this VC yet.ro Enumeration .1.3.6.1.4.1.18.3.5.9.6.7.1.18 |
wfFrSwVcXNetReceivedWhether we have received a cross net status
message for this VC during the current
polling interval.ro Enumeration .1.3.6.1.4.1.18.3.5.9.6.7.1.19 |
wfFrSwVcCalledIpAddrIndicates the IP address associated with
destination of a virtual circuit.rw IpAddress .1.3.6.1.4.1.18.3.5.9.6.7.1.20 |
wfFrSwVcCalledDlciIndicates the DLCI associated with
destination of a virtual circuit.rw INTEGER .1.3.6.1.4.1.18.3.5.9.6.7.1.21 |
wfFrSwVcTrfPriorityDefines the traffic priority level of all the
incoming packets on this VC.
FRSW_VCPRIORITY_DEFAULT - Set all incoming user
traffic packets to the default priority used by the port.
FRSW_VCPRIORITY_ONE - Set all incoming packets to priority 1.
FRSW_VCPRIORITY_TWO - Set all incoming packets to priority 2.
FRSW_VCPRIORITY_THREE - Set all incoming packets to priority 3.
Priority 0 is reserved for network critical packets like
OSPF, FR LMI and SMDS heartbeat and is not available for
user traffic.rw Enumeration .1.3.6.1.4.1.18.3.5.9.6.7.1.22 |
wfFrSwVcCreationTimeIndicates the value of sysUpTime when the VC
was created.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.18.3.5.9.6.7.1.23 |
wfFrSwVcLastTimeChangeIndicates the value of sysUpTime when last
there was a change in VC state.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.18.3.5.9.6.7.1.24 |
wfFrSwVcTxNonDeFramesIndicates the number of frames without the
DE bit sent on this virtual circuit over
the interface.ro Counter .1.3.6.1.4.1.18.3.5.9.6.7.1.25 |
wfFrSwVcTxNonDeOctetsIndicates the number of octets without DE bit
sent on this virtual circuit over the interface.ro Counter .1.3.6.1.4.1.18.3.5.9.6.7.1.26 |
wfFrSwVcTxDeFramesIndicates the number of frames with DE bit
set sent on this virtual circuit over the interface.ro Counter .1.3.6.1.4.1.18.3.5.9.6.7.1.27 |
wfFrSwVcTxDeOctetsIndicates the number of octets with DE bit set
sent on this virtual circuit over the interface.ro Counter .1.3.6.1.4.1.18.3.5.9.6.7.1.28 |
wfFrSwVcSetFecnFramesIndicates the number of frames sent to the
interface on which this switch set the FECN bit.ro Counter .1.3.6.1.4.1.18.3.5.9.6.7.1.29 |
wfFrSwVcSetFecnOctetsIndicates the number of octets in frames sent
to the interface on which this switch set the
FECN bit.ro Counter .1.3.6.1.4.1.18.3.5.9.6.7.1.30 |
wfFrSwVcSetBecnFramesIndicates the number of frames sent to the
interface on which this switch set the BECN bit.ro Counter .1.3.6.1.4.1.18.3.5.9.6.7.1.31 |
wfFrSwVcSetBecnOctetsIndicates the number of octets in frames sent to the
interface on which this switch set the BECN bit.ro Counter .1.3.6.1.4.1.18.3.5.9.6.7.1.32 |
wfFrSwVcSetDeFramesIndicates the number of frames sent to the
interface on which this switch set the DE bit.ro Counter .1.3.6.1.4.1.18.3.5.9.6.7.1.33 |
wfFrSwVcSetDeOctetsIndicates the number of octets in frames sent to the
interface on which this switch set the DE bit.ro Counter .1.3.6.1.4.1.18.3.5.9.6.7.1.34 |
wfFrSwVcDropNonDeFramesIndicates the number of frames received over the
interface which were discarded, excluding any frames
with the DE bit set.ro Counter .1.3.6.1.4.1.18.3.5.9.6.7.1.35 |
wfFrSwVcDropNonDeOctetsIndicates the number of octets in frames received over
the interface which were discarded, excluding any
frames with the DE bit set.ro Counter .1.3.6.1.4.1.18.3.5.9.6.7.1.36 |
wfFrSwVcDropDeFramesIndicates the number of frames received over the
interface, having the DE bit set, which were discarded.ro Counter .1.3.6.1.4.1.18.3.5.9.6.7.1.37 |
wfFrSwVcDropDeOctetsIndicates the number of octets in frames received over
the interface, having the DE bit set, which
were discarded.ro Counter .1.3.6.1.4.1.18.3.5.9.6.7.1.38 |
wfFrSwVcInactiveVcDropFramesIndicates how many frames were discarded because the
virtual circuit was inactive.ro Counter .1.3.6.1.4.1.18.3.5.9.6.7.1.39 |
wfFrSwVcInactiveVcDropOctetsIndicates how many Octets were discarded because the
virtual circuit was inactive.ro Counter .1.3.6.1.4.1.18.3.5.9.6.7.1.40 |
wfFrSwVcRecvNonDeFramesIndicates the number of frames received on this
virtual circuit over the interface.ro Counter .1.3.6.1.4.1.18.3.5.9.6.7.1.41 |
wfFrSwVcRecvNonDeOctetsIndicates the number of octets received on
this virtual circuit over the interface.ro Counter .1.3.6.1.4.1.18.3.5.9.6.7.1.42 |
wfFrSwVcRecvDeFramesIndicates the number of frames received over the
interface with the DE bit set.ro Counter .1.3.6.1.4.1.18.3.5.9.6.7.1.43 |
wfFrSwVcRecvDeOctetsIndicates the number of octets in frames received
over the interface with the DE bit set.ro Counter .1.3.6.1.4.1.18.3.5.9.6.7.1.44 |
wfFrSwVcRecvFecnFramesIndicates the number of frames received over the
interface with the FECN bit set.ro Counter .1.3.6.1.4.1.18.3.5.9.6.7.1.45 |
wfFrSwVcRecvFecnOctetsIndicates the number of octets in frames received
over the interface with the FECN bit set.ro Counter .1.3.6.1.4.1.18.3.5.9.6.7.1.46 |
wfFrSwVcRecvBecnFramesIndicates the number of frames received over the
interface with the BECN bit set.ro Counter .1.3.6.1.4.1.18.3.5.9.6.7.1.47 |
wfFrSwVcRecvBecnOctetsIndicates the number of octets in frames received
over the interface with the BECN bit set.ro Counter .1.3.6.1.4.1.18.3.5.9.6.7.1.48 |
wfFrSwVcRecentNonDeOctetsIndicates the number of octets received over the
interface during the most recent sampling period.ro Counter .1.3.6.1.4.1.18.3.5.9.6.7.1.49 |
wfFrSwVcXNetErrorsThis is the count of the consecutive errors
(usually timeouts) against this VC in cross-network
heartbeat polling.ro Counter .1.3.6.1.4.1.18.3.5.9.6.7.1.50 |
wfFrSwVcDropExcessBurstFramesIndicates the number of Excess Burst Frames dropped
on this virtual circuit.ro Counter .1.3.6.1.4.1.18.3.5.9.6.7.1.51 |
wfFrSwVcDropExcessBurstOctetsIndicates the number of Excess Burst Octets dropped
on this virtual circuit.ro Counter .1.3.6.1.4.1.18.3.5.9.6.7.1.52 |
wfFrSwVcInBeOctetsIndicates the maximum number Incoming Excess Burst bytes
that are allowed in a configured time interval (T).ro INTEGER .1.3.6.1.4.1.18.3.5.9.6.7.1.53 |
wfFrSwVcCfgInBeThe number of Excess Burst in bitsrw INTEGER .1.3.6.1.4.1.18.3.5.9.6.7.1.54 |
wfFrSwVcRedirectActionPerform pvc source redirect manually or based on
cross-net updates:
'redirecttoprimary(2)' will force to switch to primary;
'redirecttobackup(3)' will force to switch to backup;
'switchondemand(4)' will switch based on cross-net
status of the primary to and from primary;
'swondemandtoprimary(5)' will switch to primary from
backup iff cross-net of primary became active;
'swondemandtobackup(6)' will switch to backup from
primary iff cross-net of primary became inactive.rw Enumeration .1.3.6.1.4.1.18.3.5.9.6.7.1.55 |
wfFrSwVcRedirectTypeType of dte notification at switching time:
'transparent(1)' will not send notification to dte;
'intrusiven(2)' will send async update with NEW bit;
'intrusivea(3)' will send async update with A bit not set.rw Enumeration .1.3.6.1.4.1.18.3.5.9.6.7.1.56 |
wfFrSwVcRedirectStatePVC Source Redirect State:
'backupinactive(1)' - backup is not configured and/or cross-net status
is inactive; will allow traffic only through primary.
'primaryactive(2)' - both primary and backup rx'ed 'active' cross-net
status, currently primary is active and traffic only
through primary.
'switchtobackup(3)' - primary cross-net status is inactive, but can
not switch to backup due to manual (or semi-manual)
operation of the redirect; will allow traffic only
through primary.
'backupactive(12)' - cross-net status is 'inactive' for primary;
will allow traffic only through backup.
'switchtoprimary(13)' - cross-net status is 'active' for primary,
should by can not switch to primary due to manual
(or semi-manual) operation of the redirect; will
allow traffic only through backup.
'holddown(21)' - down state used as intermediate state at switching time
(for not more then a second); all traffic is dropped.ro Enumeration .1.3.6.1.4.1.18.3.5.9.6.7.1.57 |
wfFrSwVcBackupCalledIpAddrBackup Called Ip Address of the remote end of the PVC.rw IpAddress .1.3.6.1.4.1.18.3.5.9.6.7.1.58 |
wfFrSwVcBackupCalledDlciBackup Called Dlci of the remote end of the PVC.rw INTEGER .1.3.6.1.4.1.18.3.5.9.6.7.1.59 |
wfFrSwVcBackupCrossNetStatusCross net status of the backup remote end of the PVC.ro Enumeration .1.3.6.1.4.1.18.3.5.9.6.7.1.60 |
wfFrSwVcBackupCrossNetErrorsSupport counter of missed cross net update from backup
remote end of the PVC, range: [0, wfFrSwDlcmiCrossNetErrorThreshold].ro INTEGER .1.3.6.1.4.1.18.3.5.9.6.7.1.61 |
wfFrSwVcAtmIwfModeThis attribute indicates the mode of FR-ATM interworking over
this FR PVC or that FR-ATM interworking is not enabled on it.rw Enumeration .1.3.6.1.4.1.18.3.5.9.6.7.1.62 |
wfFrSwVcAtmIwfVPIThis is relevant only when the ATM/FR interworking is enabled
for this PVC. This indicates the ATM virtual path identifier
associated with the Frame Relay PVC described by this record
virtual circuit identifier.rw INTEGER .1.3.6.1.4.1.18.3.5.9.6.7.1.63 |
wfFrSwVcAtmIwfVCIThis is relevant only when FR/ATM interworking is enabled
for this PVC. This indicates the ATM virtual circuit
identifier associated with the Frame Relay PVC described by
this record.rw INTEGER .1.3.6.1.4.1.18.3.5.9.6.7.1.64 |
wfFrSwVcAtmIwfLossPriorityPolicyThis is relevant only when FR/ATM interworking is enabled
for this FR PVC. This indicates the policy for translating
ATM CLP to FR DE on this PVC or simply setting FR DE to a
constant value for all frames.rw Enumeration .1.3.6.1.4.1.18.3.5.9.6.7.1.65 |
wfFrSwVcAtmIwfDePolicyThis is relevant only when FR/ATM interworking is enabled
for this FR PVC. This indicates the policy on this PVC for
translating FR DE to ATM CLP or simply setting CLP to a
constant value for all frames.rw Enumeration .1.3.6.1.4.1.18.3.5.9.6.7.1.66 |
wfFrSwVcAtmIwfEfciPolicyThis is relevant only when FR/ATM interworking is enabled
for this FR PVC. This indicates the policy on this PVC for
translating FR FECN to ATM EFCI or simply setting ATM EFCI
to a constant value for all frames.rw Enumeration .1.3.6.1.4.1.18.3.5.9.6.7.1.67 |
wfFrSwVcEscapeEnableIdentifies this PVC as either a standard FRSW PVC (escape
disabled) or an Escape PVC (escape enabled). The type of
Escape PVC (ingress node or egress node) is specified in the
wfFrSwDlcmiEntry Object.rw Enumeration .1.3.6.1.4.1.18.3.5.9.6.7.1.68 |
wfFrSwVcSpvcCallStateIndicates to the state of the SPVC call for this DLCI.ro Enumeration .1.3.6.1.4.1.18.3.5.9.6.7.1.69 |
wfFrSwVcCallReqCalledAddrCalled E.164/X.121 Address for an SPVC Call Request
Agent. The address type is determined by the
wfFrSwDlcmiL2AddrType attribute in wfFrSwDlcmiEntry.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.18.3.5.9.6.7.1.70 |
wfFrSwVcCallReqDlciSelectionTypeIndicates to the Calling End of an SPVC Call Request whether
to use any available DLCI, or a specific DLCI. If 'specific'
is chosen, the called DLCI value is specified in
wfFrSwVcCallReqCalledDlci.rw Enumeration .1.3.6.1.4.1.18.3.5.9.6.7.1.71 |
wfFrSwVcCallReqCalledDlciIndicates to the Calling End of an SPVC Call Request the
DLCI to be used at the destination of a virtual circuit.
This value should be specified when 'specific'
wfFrSwVcCallReqDlciSelectionType is chosen.rw INTEGER .1.3.6.1.4.1.18.3.5.9.6.7.1.72 |
wfFrSwVcCallReqRetryTimerIndicates the number of minutes the Call Request Agent should
wait for an SPVC CONNECT message before declaring a Call Setup
request REJECTED.rw INTEGER .1.3.6.1.4.1.18.3.5.9.6.7.1.73 |
wfFrSwVcCallReqMaxRetriesIndicates the number of times the Call Request Agent should
retry failed Call Setup requests before declaring the SPVC
invalid.rw INTEGER .1.3.6.1.4.1.18.3.5.9.6.7.1.74 |
wfFrSwIsdnBaseTableThis is a FRSW over ISDN configuration table. This
table specifies whether the Calling Party (ANI) or Called
Party (DNIS) ISDN Phone Number should be used to map
the ISDN call to a particular FRSW UNI. The table is
indexed by the Slot Number where the PRI(s) exist. SEQUENCE OF WfFrSwIsdnBaseEntry .1.3.6.1.4.1.18.3.5.9.6.8 |
wfFrSwIsdnBaseEntryInstance Id for this table. WfFrSwIsdnBaseEntry .1.3.6.1.4.1.18.3.5.9.6.8.1 |
wfFrSwIsdnBaseDeleteIndication to delete this FRSW ISDN interface.rw Enumeration .1.3.6.1.4.1.18.3.5.9.6.8.1.1 |
wfFrSwIsdnBaseSlotNumThis number is the Slot Number for the PRI interface(s)
that are being configured for FRSW ISDN. There will be
one of these tables for every slot where an FRSW ISDN
PRI Interface exists.ro INTEGER .1.3.6.1.4.1.18.3.5.9.6.8.1.2 |
wfFrSwIsdnBaseAssocTypeIndicates which ISDN Phone Number (ANI or DNIS)
to use to do the ISDN call to FRSW UNI mapping.rw Enumeration .1.3.6.1.4.1.18.3.5.9.6.8.1.3 |
wfFrSwIsdnAssocTableThis table defines the Association Table
to be used for the FRSW over ISDN application.
The table contains a list of ISDN Phone
Numbers and the associated FRSW UNI Index Number.
The table is indexed by the Slot Number and the
ISDN Phone Number. SEQUENCE OF WfFrSwIsdnAssocEntry .1.3.6.1.4.1.18.3.5.9.6.9 |
wfFrSwIsdnAssocEntryInstance Id for this table. WfFrSwIsdnAssocEntry .1.3.6.1.4.1.18.3.5.9.6.9.1 |
wfFrSwIsdnAssocDeleteIndication to delete this Association Instance.rw Enumeration .1.3.6.1.4.1.18.3.5.9.6.9.1.1 |
wfFrSwIsdnAssocSlotNumSlot with which this ISDN Phone Number is associated.ro INTEGER .1.3.6.1.4.1.18.3.5.9.6.9.1.2 |
wfFrSwIsdnAssocNumISDN Phone Number that is used to look up the
appropriate FRSW UNI Index. This number is
compared with either the Calling Party Number (ANI)
Information Element or the Called Party Number (DNIS)
Information Element contained in the ISDN Call
Setup Message.ro OCTET STRING .1.3.6.1.4.1.18.3.5.9.6.9.1.3 |
wfFrSwIsdnAssocScrnEnableIndicate whether allowed screening should be
enabled or disabled for all of the UNIs
contained in the FRSW UNI Index.rw Enumeration .1.3.6.1.4.1.18.3.5.9.6.9.1.4 |
wfFrSwIsdnAssocIndexA number that indicates the FRSW UNI Index that is
is associated with the ISDN Phone Number. This
FRSW UNI Index is used as a key to obtain the UNIs and
the Screening information from the wfFrSwIsdnScrnEntry and
wfFrSwIsdnUniEntry mibs. The default for the index is
2**31 - 1 = 2147483647 = 0x7FFFFFFF, which represents
an unconfigured index number.rw INTEGER .1.3.6.1.4.1.18.3.5.9.6.9.1.5 |
wfFrSwIsdnUniTableThis table is used by the FRSW over ISDN
application. The table defines a list
of FRSW UNIs that are to be collected into
a hunt group identifiable by an Index Number. SEQUENCE OF WfFrSwIsdnUniEntry .1.3.6.1.4.1.18.3.5.9.6.10 |
wfFrSwIsdnUniEntryInstance Id for this table. WfFrSwIsdnUniEntry .1.3.6.1.4.1.18.3.5.9.6.10.1 |
wfFrSwIsdnUniDeleteIndication to delete this FRSW UNI Index
Instance.rw Enumeration .1.3.6.1.4.1.18.3.5.9.6.10.1.1 |
wfFrSwIsdnUniIndexFRSW UNI Index
a group of related FRSW UNIs that are
collected together as a hunt group. This number
ties this entry to an entry in
wfFrSwIsdnAssocEntry.ro INTEGER .1.3.6.1.4.1.18.3.5.9.6.10.1.2 |
wfFrSwIsdnUniNumA FRSW UNI/Circuit.ro INTEGER .1.3.6.1.4.1.18.3.5.9.6.10.1.3 |
wfFrSwIsdnUniStateState of this UNI (available or in-use).ro Enumeration .1.3.6.1.4.1.18.3.5.9.6.10.1.4 |
wfFrSwIsdnScrnTableThis is the incoming call screening table
for the FRSW over ISDN application. The table
consists of a FRSW UNI Index and a list of allowable
ISDN Phone numbers for that FRSW UNI Index.
The table is indexed by both the FRSW UNI Index
and the ISDN Phone Number.
This table is referenced only when the
wfFrSwIsdnAssocScrnEnable is set to
Enabled for this FRSW UNI Index. SEQUENCE OF WfFrSwIsdnScrnEntry .1.3.6.1.4.1.18.3.5.9.6.11 |
wfFrSwIsdnScrnEntryInstance Id for this table. WfFrSwIsdnScrnEntry .1.3.6.1.4.1.18.3.5.9.6.11.1 |
wfFrSwIsdnScrnDeleteIndication to delete this Scrn Instance.rw Enumeration .1.3.6.1.4.1.18.3.5.9.6.11.1.1 |
wfFrSwIsdnScrnIndexFRSW UNI Index - A number that ties this
entry to an entry in wfFrSwIsdnAssocEntry.ro INTEGER .1.3.6.1.4.1.18.3.5.9.6.11.1.2 |
wfFrSwIsdnScrnNumISDN Phone Number of a user authorized to
access the UNIs contained in the FRSW
UNI Index.ro OCTET STRING .1.3.6.1.4.1.18.3.5.9.6.11.1.3 |
wfFrSwSigTableThe Frame relay signalling table contains frame relay
signalling entries indexed by the frame relay access
channel circuit number. An instance of wfFrSwSigEntry
is required for each frame relay access channel with
frame relay signalling enabled. The absence of
wfFrSwSigEntry for a given frame relay access channel
implies that frame relay signalling is disabled for the
circuit. Note that the terms 'incoming' and 'outgoing'
refer to the frame mode call with respect to the network
side of the interface. The terminology used by CCITT
Q.933/Q.931 is different. SEQUENCE OF WfFrSwSigEntry .1.3.6.1.4.1.18.3.5.9.6.12 |
wfFrSwSigEntryAn entry in the Frame Relay signalling port
information table. WfFrSwSigEntry .1.3.6.1.4.1.18.3.5.9.6.12.1 |
wfFrSwSigDeleteIndication to delete this instancerw Enumeration .1.3.6.1.4.1.18.3.5.9.6.12.1.1 |
wfFrSwSigCircuitThe circuit number for this frame relay access channelro INTEGER .1.3.6.1.4.1.18.3.5.9.6.12.1.2 |
wfFrSwSigSvcDlciLowLowest DLCI to be used for SVC, the default value
is for 2 octet frame headerrw INTEGER .1.3.6.1.4.1.18.3.5.9.6.12.1.3 |
wfFrSwSigSvcDlciHighHighest DLCI to be used for SVC, the default value
is for 2 octet frame header.rw INTEGER .1.3.6.1.4.1.18.3.5.9.6.12.1.4 |
wfFrSwSigDlciAssignDetermines if DLCI's are assigned starting
at wfFrSwSigSvcDlciHigh and working towards
wfFrSwSigSvcDlciLow or vice versa.rw Enumeration .1.3.6.1.4.1.18.3.5.9.6.12.1.5 |
wfFrSwSigMaxNumOfSvcsIndicates the maximum number of simultaneous switched
virtual circuits allowed on the logical line.rw INTEGER .1.3.6.1.4.1.18.3.5.9.6.12.1.6 |
wfFrSwSigNumOfSvcsInUseIndicates the number of switched virtual circuits
in use on the logical line.ro INTEGER .1.3.6.1.4.1.18.3.5.9.6.12.1.7 |
wfFrSwSigDefaultThroughputThis value is used by the network in the Link Layer
Core Parameters IE incoming & outgoing throughput
fields when they are not included in the setup message
by the user.rw INTEGER .1.3.6.1.4.1.18.3.5.9.6.12.1.8 |
wfFrSwSigDefaultMinAcceptThroughputThis value is used by the network in the Link Layer
Core Parameters IE incoming & outgoing minimum acceptable
throughput fields when they are not included in the
setup message by the user.rw INTEGER .1.3.6.1.4.1.18.3.5.9.6.12.1.9 |
wfFrSwSigDefaultBcThis value is used by the network in the Link Layer
Core Parameters IE incoming & outgoing Bc fields when
they are not included in the setup message by the user.ro INTEGER .1.3.6.1.4.1.18.3.5.9.6.12.1.10 |
wfFrSwSigDefaultBeThis value is used by the network in the Link Layer
Core Parameters IE incoming & outgoing Be fields when
they are not included in the setup message by the user.rw INTEGER .1.3.6.1.4.1.18.3.5.9.6.12.1.11 |
wfFrSwSigMaxInThroughputPerSvcThis is the maximum incoming throughput that any
single SVC may negotiate for a call. Calls requesting
in excess of this attribute are rejected.rw INTEGER .1.3.6.1.4.1.18.3.5.9.6.12.1.12 |
wfFrSwSigMaxOutThroughputPerSvcThis is the maximum outgoing throughput that any
single SVC may negotiate for a call. Calls requesting
in excess of this attribute are rejected.rw INTEGER .1.3.6.1.4.1.18.3.5.9.6.12.1.13 |
wfFrSwSigTotalInNegotiableThroughputThis is the total maximum incoming throughput that is
available for all frame mode calls on the port. If the
sum of the incoming throughput requested by a call
and wfFrSwSigTotalInCurrentThroughput is in excess of
this value, the call is rejected.rw INTEGER .1.3.6.1.4.1.18.3.5.9.6.12.1.14 |
wfFrSwSigTotalInCurrentThroughputThis is the total incoming throughput that has been
negotiated for use by all SVC's on the port.ro INTEGER .1.3.6.1.4.1.18.3.5.9.6.12.1.15 |
wfFrSwSigTotalOutNegotiableThroughputThis is the total maximum outgoing throughput that is
available for all frame mode calls on the port. If the
sum of the outgoing throughput requested by a call
and wfFrSwSigTotalOutCurrentThroughput is in excess of
this value, the call is rejected.rw INTEGER .1.3.6.1.4.1.18.3.5.9.6.12.1.16 |
wfFrSwSigTotalOutCurrentThroughputThis is the total incoming throughput that has been
negotiated for use by all SVC's on the port.ro INTEGER .1.3.6.1.4.1.18.3.5.9.6.12.1.17 |
wfFrSwSigXNetClearingDisableIf cross-net polling (wfFrSwDlcmiCrossNetEnable) is
enabled on this interface, and the error threshold
(wfFrSwDlcmiCrossNetErrorThreshold) is exceeded, the
network can clear the call.rw Enumeration .1.3.6.1.4.1.18.3.5.9.6.12.1.18 |
wfFrSwSigCallingPartyIEMandatoryReject the call if the Calling Party IE is absent in the
setup message or if the provided Calling Party IE fails
address authentication tests againt the configured
address(es) on the ingress logical line.rw Enumeration .1.3.6.1.4.1.18.3.5.9.6.12.1.19 |
wfFrSwSigT301Timer number: T301
default time-out: 3 min
state of call: call initiated
cause for start: incoming setup
normal stop: outgoing connect
at the first expiry: clear call
at the second expiry: timer not restartedrw INTEGER .1.3.6.1.4.1.18.3.5.9.6.12.1.20 |
wfFrSwSigT303Timer number: T303
default time-out: 4 s
state of call: call present
cause for start: outgoing setup
normal stop: incoming connect/call-proceeding/
release-complete
at the first expiry: retransmit setup, restart T303
at the second expiry: clear callrw INTEGER .1.3.6.1.4.1.18.3.5.9.6.12.1.21 |
wfFrSwSigT305Timer number: T305
default time-out: 30 s
state of call: disconnect ind
cause for start: outgoing disconnect
normal stop: incoming release/disconnect
at the first expiry: outgoing release
at the second expiry: timer not restartedrw INTEGER .1.3.6.1.4.1.18.3.5.9.6.12.1.22 |
wfFrSwSigT308Timer number: T308
default time-out: 4 s
state of call: release req
cause for start: outgoing release
normal stop: incoming release/release-complete
at the first expiry: retransmit release, restart T308
at the second expiry: place access channel in maintenancerw INTEGER .1.3.6.1.4.1.18.3.5.9.6.12.1.23 |
wfFrSwSigT310Timer number: T310
default time-out: 10 s
state of call: incoming call proceeding
cause for start: incoming call proceeding
normal stop: incoming connect/disconnect
at the first expiry: clear call
at the second expiry: timer not restartedrw INTEGER .1.3.6.1.4.1.18.3.5.9.6.12.1.24 |
wfFrSwSigT322Timer number: T322
default time-out: 4 s
state of call: any call state
cause for start: outgoing status enquiry
normal stop: incoming status/disconnect/
release/release-complete
at the first expiry: retransmit status-enq, restart T322
at the second expiry: resend status enq and restart T322rw INTEGER .1.3.6.1.4.1.18.3.5.9.6.12.1.25 |
wfFrSwSigInSetupPktsnumber of incoming setup packetsro Counter .1.3.6.1.4.1.18.3.5.9.6.12.1.26 |
wfFrSwSigInCallProceedingPktsnumber of incoming call proceeding packetsro Counter .1.3.6.1.4.1.18.3.5.9.6.12.1.27 |
wfFrSwSigInConnectPktsnumber of incoming connect packetsro Counter .1.3.6.1.4.1.18.3.5.9.6.12.1.28 |
wfFrSwSigInDisconnectPktsnumber of incoming disconnect packetsro Counter .1.3.6.1.4.1.18.3.5.9.6.12.1.29 |
wfFrSwSigInReleasePktsnumber of incoming release packetsro Counter .1.3.6.1.4.1.18.3.5.9.6.12.1.30 |
wfFrSwSigInReleaseCompletePktsnumber of incoming release complete packetsro Counter .1.3.6.1.4.1.18.3.5.9.6.12.1.31 |
wfFrSwSigInStatusEnquiryPktsnumber of incoming status enquiry packetsro Counter .1.3.6.1.4.1.18.3.5.9.6.12.1.32 |
wfFrSwSigInStatusPktsnumber of incoming status packetsro Counter .1.3.6.1.4.1.18.3.5.9.6.12.1.33 |
wfFrSwSigInUnknownPktsnumber of incoming unknown packetsro Counter .1.3.6.1.4.1.18.3.5.9.6.12.1.34 |
wfFrSwSigOutSetupPktsnumber of outgoing setup packetsro Counter .1.3.6.1.4.1.18.3.5.9.6.12.1.35 |
wfFrSwSigOutCallProceedingPktsnumber of outgoing call proceeding packetsro Counter .1.3.6.1.4.1.18.3.5.9.6.12.1.36 |
wfFrSwSigOutConnectPktsnumber of outgoing connect packetsro Counter .1.3.6.1.4.1.18.3.5.9.6.12.1.37 |
wfFrSwSigOutDisconnectPktsnumber of outgoing disconnect packetsro Counter .1.3.6.1.4.1.18.3.5.9.6.12.1.38 |
wfFrSwSigOutReleasePktsnumber of outgoing release packetsro Counter .1.3.6.1.4.1.18.3.5.9.6.12.1.39 |
wfFrSwSigOutReleaseCompletePktsnumber of outgoing release packestro Counter .1.3.6.1.4.1.18.3.5.9.6.12.1.40 |
wfFrSwSigOutStatusEnquiryPktsnumber of outgoing status enquiry packetsro Counter .1.3.6.1.4.1.18.3.5.9.6.12.1.41 |
wfFrSwSigOutStatusPktsnumber of outgoing status packetsro Counter .1.3.6.1.4.1.18.3.5.9.6.12.1.42 |
wfFrSwSigRejectedConnRequestsnumber of connections rejectedro Counter .1.3.6.1.4.1.18.3.5.9.6.12.1.43 |
wfFrSwSigNwrkAbortedConnectionsnumber of connections aborted by networkro Counter .1.3.6.1.4.1.18.3.5.9.6.12.1.44 |
wfFrSwSigL2Resetsnumber of L2 resetsro Counter .1.3.6.1.4.1.18.3.5.9.6.12.1.45 |
wfFrSwSigDlciIEAllowedReject the call if the Dlci IE is present in the setup
message and wfFrSwSigDlciIEAllowed is set to disabled.rw Enumeration .1.3.6.1.4.1.18.3.5.9.6.12.1.46 |
wfFrSwSigX213PriorityIEAllowedReject the call if the X213 Priority IE is present in
setup message and wfFrSwSigX213PriorityIEAllowed is set
to disabled.rw Enumeration .1.3.6.1.4.1.18.3.5.9.6.12.1.47 |
wfFrSwSigMaximumBeThis value is the maximum allowed Be for a SVC connectionrw INTEGER .1.3.6.1.4.1.18.3.5.9.6.12.1.48 |
wfFrSwGlobalE164AddrTablewfFrSwGlobalE164AddrTable is used by Directory Services
to translate a range of E.164 addresses into an
internal IP network address. E.164 ranges must not ever overlap. SEQUENCE OF WfFrSwGlobalE164AddrEntry .1.3.6.1.4.1.18.3.5.9.6.13 |
wfFrSwGlobalE164AddrEntryAn entry in the Frame Relay Global E.164 Address Table. WfFrSwGlobalE164AddrEntry .1.3.6.1.4.1.18.3.5.9.6.13.1 |
wfFrSwGlobalE164AddrDeleteIndication to delete/create this entry.rw Enumeration .1.3.6.1.4.1.18.3.5.9.6.13.1.1 |
wfFrSwGlobalE164AddrLowInstance identifier; the low end of the E.164
address range. This is an 8-byte fixed length octet
string format, right justified with padded leading zeros
as necessary.ro OCTET STRING .1.3.6.1.4.1.18.3.5.9.6.13.1.2 |
wfFrSwGlobalE164AddrHighInstance identifier; the high end of the E.164
address range. This is an 8-byte fixed length octet
string format, right justified with padded leading zeros
as necessary.ro OCTET STRING .1.3.6.1.4.1.18.3.5.9.6.13.1.3 |
wfFrSwGlobalE164AddrIPAddrThis is the internal IP network address associated with
this range of E.164 addresses.rw IpAddress .1.3.6.1.4.1.18.3.5.9.6.13.1.4 |
wfFrSwGlobalX121AddrTablewfFrSwGlobalX121AddrTable is used by Directory Services
to translate a range of X.121 addresses into an
internal IP network address. X.121 ranges must not ever overlap. SEQUENCE OF WfFrSwGlobalX121AddrEntry .1.3.6.1.4.1.18.3.5.9.6.14 |
wfFrSwGlobalX121AddrEntryAn entry in the Frame Relay Global X.121 Address Table. WfFrSwGlobalX121AddrEntry .1.3.6.1.4.1.18.3.5.9.6.14.1 |
wfFrSwGlobalX121AddrDeleteIndication to delete/create this entry.rw Enumeration .1.3.6.1.4.1.18.3.5.9.6.14.1.1 |
wfFrSwGlobalX121AddrLowInstance identifier; the low end of the X.121
address range. This is an 8-byte fixed length octet
string format, right justified with padded leading zeros
as necessary.ro OCTET STRING .1.3.6.1.4.1.18.3.5.9.6.14.1.2 |
wfFrSwGlobalX121AddrHighInstance identifier; the high end of the X.121
address range. This is an 8-byte fixed length octet
string format, right justified with padded leading zeros
as necessary.ro OCTET STRING .1.3.6.1.4.1.18.3.5.9.6.14.1.3 |
wfFrSwGlobalX121AddrIPAddrThis is the internal IP network address associated with
this range of X.121 addresses.rw IpAddress .1.3.6.1.4.1.18.3.5.9.6.14.1.4 |
wfFrSwLocalE164AddrTablewfFrSwLocalE164AddrTable contains E.164 addresses on the
local BNX and CUG (Closed User Group) related information. SEQUENCE OF WfFrSwLocalE164AddrEntry .1.3.6.1.4.1.18.3.5.9.6.15 |
wfFrSwLocalE164AddrEntryAn entry in the Frame Relay Local E.164 Address Table. WfFrSwLocalE164AddrEntry .1.3.6.1.4.1.18.3.5.9.6.15.1 |
wfFrSwLocalE164AddrDeleteIndication to delete/create this entry.rw Enumeration .1.3.6.1.4.1.18.3.5.9.6.15.1.1 |
wfFrSwLocalE164AddrCctInstance identifier; internal CCT number associated
with this E.164 address.ro INTEGER .1.3.6.1.4.1.18.3.5.9.6.15.1.2 |
wfFrSwLocalE164AddressInstance identifier; an E.164 address.
This is an 8-byte fixed length octet string format,
right justified with padded leading zeros as necessary.ro OCTET STRING .1.3.6.1.4.1.18.3.5.9.6.15.1.3 |
wfFrSwLocalE164AddrCUGCUG (Closed User Group) information.
The structure of the CUG information consists zero or
more groups (number of groups can be derived from the
OCTET STRING data type of this MIB attribute) of COI
structure information. Each COI structure consists of
a COI group number (4-byte integer) and a COI list.
Each COI list consists of a length field (4-byte integer)
which specifies the number of bytes of COI bit-encoded
information belonging to this group and the COI information
structure. COI information structure is a bit mask field
where each bit from left to right represents whether this
E.164 address belongs to a particular COI number within this
COI group number.
Please note that COI group numbers can not be repeated and
that the COI group numbers must be in increasing order in the
CUG configuration MIB
wfFrSwLocalE164AddrCUG defaults to zero COI groups which
means no CUG related information and hence this local
wfFrSwLocalE164Address is allowed to communicate with
all users.rw OCTET STRING .1.3.6.1.4.1.18.3.5.9.6.15.1.4 |
wfFrSwLocalE164AddrLocalFlagLocal/Non-Local Identifier Flag. Used for SPVCs.rw Enumeration .1.3.6.1.4.1.18.3.5.9.6.15.1.5 |
wfFrSwLocalX121AddrTablewfFrSwLocalX121AddrTable contains X.121 addresses on the
local BNX and CUG (Closed User Group) related information. SEQUENCE OF WfFrSwLocalX121AddrEntry .1.3.6.1.4.1.18.3.5.9.6.16 |
wfFrSwLocalX121AddrEntryAn entry in the Frame Relay Local X.121 Address Table. WfFrSwLocalX121AddrEntry .1.3.6.1.4.1.18.3.5.9.6.16.1 |
wfFrSwLocalX121AddrDeleteIndication to delete/create this entry.rw Enumeration .1.3.6.1.4.1.18.3.5.9.6.16.1.1 |
wfFrSwLocalX121AddrCctInstance identifier; internal CCT number associated
with this X.121 address.ro INTEGER .1.3.6.1.4.1.18.3.5.9.6.16.1.2 |
wfFrSwLocalX121AddressInstance identifier; a X.121 address.
This is an 8-byte fixed length octet string format,
right justified with padded leading zeros as necessary.ro OCTET STRING .1.3.6.1.4.1.18.3.5.9.6.16.1.3 |
wfFrSwLocalX121AddrCUGCUG (Closed User Group) information.
The structure of the CUG information consists zero or
more groups (number of groups can be derived from the
OCTET STRING data type of this MIB attribute) of COI
structure information. Each COI structure consists of
a COI group number (4-byte integer) and a COI list.
Each COI list consists of a length field (4-byte integer)
which specifies the number of bytes of COI bit-encoded
information belonging to this group and the COI information
structure. COI information structure is a bit mask field
where each bit from left to right represents whether this
X.121 address belongs to a particular COI number within this
COI group number.
wfFrSwLocalX121AddrCUG defaults to zero COI groups which
means no CUG related information and hence this local
wfFrSwLocalX121Address is allowed to communicate with
all users.rw OCTET STRING .1.3.6.1.4.1.18.3.5.9.6.16.1.4 |
wfFrSwLocalX121AddrLocalFlagLocal/Non-Local Identifier Flag. Used for SPVCs.rw Enumeration .1.3.6.1.4.1.18.3.5.9.6.16.1.5 |
wfFrSwBase OBJECT IDENTIFIER .1.3.6.1.4.1.18.3.5.9.6.17 |
wfFrSwBaseDeleteIndication to delete/create this base grouprw Enumeration .1.3.6.1.4.1.18.3.5.9.6.17.1 |
wfFrSwBaseIpAddrIndicates this BNX's (circuit-less) IP addressrw IpAddress .1.3.6.1.4.1.18.3.5.9.6.17.2 |
wfFrSwBaseShutDownBit mask for slots to shutdown, slots 1-14. The MSBit
represents slot 1, the next most significant bit represents
slot 2, and so forth.rw Counter .1.3.6.1.4.1.18.3.5.9.6.17.3 |
wfFrSwCngcMonTableThis table is used by FRSW Congestion Control application.
The table is used to Monitor the congestion level of a
particular circuit. SEQUENCE OF WfFrSwCngcMonEntry .1.3.6.1.4.1.18.3.5.9.6.18 |
wfFrSwCngcMonEntryInstance Id for this table. WfFrSwCngcMonEntry .1.3.6.1.4.1.18.3.5.9.6.18.1 |
wfFrSwCngcMonResetIndication to reset Cngc Monitor Counters.rw INTEGER .1.3.6.1.4.1.18.3.5.9.6.18.1.1 |
wfFrSwCngcMonCctCircuit to be monitored.ro INTEGER .1.3.6.1.4.1.18.3.5.9.6.18.1.2 |
wfFrSwCngcMonP0Level1PercentPercentage of time congestion is at level 1.
for Priority 0 Traffic.ro Gauge .1.3.6.1.4.1.18.3.5.9.6.18.1.3 |
wfFrSwCngcMonP0Level2PercentPercentage of time congestion is at level 2.
for Priority 0 Traffic.ro Gauge .1.3.6.1.4.1.18.3.5.9.6.18.1.4 |
wfFrSwCngcMonP0Level3PercentPercentage of time congestion is at level 3.
for Priority 0 Traffic.ro Gauge .1.3.6.1.4.1.18.3.5.9.6.18.1.5 |
wfFrSwCngcMonP0Level4PercentPercentage of time congestion is at level 4.
for Priority 0 Traffic.ro Gauge .1.3.6.1.4.1.18.3.5.9.6.18.1.6 |
wfFrSwCngcMonP1Level1PercentPercentage of time congestion is at level 1.
for Priority 1 Traffic.ro Gauge .1.3.6.1.4.1.18.3.5.9.6.18.1.7 |
wfFrSwCngcMonP1Level2PercentPercentage of time congestion is at level 2.
for Priority 1 Traffic.ro Gauge .1.3.6.1.4.1.18.3.5.9.6.18.1.8 |
wfFrSwCngcMonP1Level3PercentPercentage of time congestion is at level 3.
for Priority 1 Traffic.ro Gauge .1.3.6.1.4.1.18.3.5.9.6.18.1.9 |
wfFrSwCngcMonP1Level4PercentPercentage of time congestion is at level 4.
for Priority 1 Traffic.ro Gauge .1.3.6.1.4.1.18.3.5.9.6.18.1.10 |
wfFrSwCngcMonP2Level1PercentPercentage of time congestion is at level 1.
for Priority 2 Traffic.ro Gauge .1.3.6.1.4.1.18.3.5.9.6.18.1.11 |
wfFrSwCngcMonP2Level2PercentPercentage of time congestion is at level 2.
for Priority 2 Traffic.ro Gauge .1.3.6.1.4.1.18.3.5.9.6.18.1.12 |
wfFrSwCngcMonP2Level3PercentPercentage of time congestion is at level 3.
for Priority 2 Traffic.ro Gauge .1.3.6.1.4.1.18.3.5.9.6.18.1.13 |
wfFrSwCngcMonP2Level4PercentPercentage of time congestion is at level 4.
for Priority 2 Traffic.ro Gauge .1.3.6.1.4.1.18.3.5.9.6.18.1.14 |
wfFrSwCngcMonP3Level1PercentPercentage of time congestion is at level 1.
for Priority 3 Traffic.ro Gauge .1.3.6.1.4.1.18.3.5.9.6.18.1.15 |
wfFrSwCngcMonP3Level2PercentPercentage of time congestion is at level 2.
for Priority 3 Traffic.ro Gauge .1.3.6.1.4.1.18.3.5.9.6.18.1.16 |
wfFrSwCngcMonP3Level3PercentPercentage of time congestion is at level 3.
for Priority 3 Traffic.ro Gauge .1.3.6.1.4.1.18.3.5.9.6.18.1.17 |
wfFrSwCngcMonP3Level4PercentPercentage of time congestion is at level 4.
for Priority 3 Traffic.ro Gauge .1.3.6.1.4.1.18.3.5.9.6.18.1.18 |
wfFrSwVirtualIntfTableThe table is used to create 'virtual' FRSW access lines. SEQUENCE OF WfFrSwVirtualIntfEntry .1.3.6.1.4.1.18.3.5.9.6.19 |
wfFrSwVirtualIntfEntryInstance Id for this table. WfFrSwVirtualIntfEntry .1.3.6.1.4.1.18.3.5.9.6.19.1 |
wfFrSwVirtualIntfDeleteIndication to delete this virtual interface.rw Enumeration .1.3.6.1.4.1.18.3.5.9.6.19.1.1 |
wfFrSwVirtualIntfSlotInstance identifier; the slot number of this interface.ro INTEGER .1.3.6.1.4.1.18.3.5.9.6.19.1.2 |
wfFrSwVirtualIntfCctInstance identifier; the circuit number of this interface.ro INTEGER .1.3.6.1.4.1.18.3.5.9.6.19.1.3 |
wfFrSwVirtualIntfLineNumLine number for this virtual interface.ro INTEGER .1.3.6.1.4.1.18.3.5.9.6.19.1.4 |
wfFrSwExtFileSysTableThis table is used by FRSW to extend the file system
to DRAM device. SEQUENCE OF WfFrSwExtFileSysEntry .1.3.6.1.4.1.18.3.5.9.6.20 |
wfFrSwExtFileSysEntryInstance Id for this table. WfFrSwExtFileSysEntry .1.3.6.1.4.1.18.3.5.9.6.20.1 |
wfFrSwExtFileSysDeleteIndication to delete/create this entry.rw Enumeration .1.3.6.1.4.1.18.3.5.9.6.20.1.1 |
wfFrSwExtFileSysSlotA unique value for each slot.
Its value ranges between 1 and 14.ro INTEGER .1.3.6.1.4.1.18.3.5.9.6.20.1.2 |
wfFrSwExtFileSysSizeThe memory size of the extended file system in
byte unit. The value zero also means that extended
file system is disabled. Non-zero value
means enabled. Its suggested that the size
is in multiple of 128k bytes.
Some of the well-known memory sizes and their correspond
decimal values are as followed:
Mem size Decimal Value
^^^^^^^^ ^^^^^^^^^^^^^
128K 131072
256K 262144
512K 524288
1M 1048576
2M 2097152
4M 4194304
8M 8388608rw INTEGER .1.3.6.1.4.1.18.3.5.9.6.20.1.3 |
wfFrSwExtFileSysActualSizeThe actual memory size the system allocated.ro INTEGER .1.3.6.1.4.1.18.3.5.9.6.20.1.4 |
wfFrSwExtFileSysStateThe status of the extended file system.
State up indicates that the requested memory size
for the extended file system has been allocated
successfully and the extended file system is in
operational state.
State fault indicates that the requested memory size
for the extended file system has NOT been allocated
successfully and the extended file system is NOT
in operational state. One reason for entering the
fault state is insufficient available memory.
State init indicates that the system is in the
initialization cycle. The extended file system
is not operational.
State notpresent reflects the size of zero.ro Enumeration .1.3.6.1.4.1.18.3.5.9.6.20.1.5 |
wfFrSwDlcmiEntryThe parameters for a particular Data Link Connection
Management Interface. WfFrSwDlcmiEntry .wfFrSwDlcmiTable.1 |
wfFrSwDlcmiDeleteIndication to delete this frame relay interface.rw Enumeration .wfFrSwDlcmiTable.1.1 |
wfFrSwDlcmiStateIndicates which state of DLCMI the interface is inro Enumeration .wfFrSwDlcmiTable.1.2 |
wfFrSwDlcmiNniEnableIndicates whether a NNI is enabled for this entry.rw Enumeration .wfFrSwDlcmiTable.1.3 |
wfFrSwDlcmiCircuitInstance identifier; the circuit number of this entry.ro INTEGER .wfFrSwDlcmiTable.1.4 |
wfFrSwDlcmiManagementTypeIndicates the Data Link Connection Management scheme
that is active.rw Enumeration .wfFrSwDlcmiTable.1.5 |
wfFrSwL3NetAddressIndicates level 3 (IP) address of this frame relay interfacerw IpAddress .wfFrSwDlcmiTable.1.6 |
wfFrSwDlcmiAddressLenIndicates the address length, including the
control portion.rw Enumeration .wfFrSwDlcmiTable.1.7 |
wfFrSwDlcmiControlByteDisableIndicates inclusion of control byte in q922 format.rw Enumeration .wfFrSwDlcmiTable.1.8 |
wfFrSwDlcmiPollingIntervalThe number of seconds between successive status enquiry
messages.rw INTEGER .wfFrSwDlcmiTable.1.9 |
wfFrSwDlcmiFullEnquiryIntervalIndicates the number of status enquiries before a full
status enquiry. (For bidirectional procedures.)rw INTEGER .wfFrSwDlcmiTable.1.10 |
wfFrSwDlcmiErrorThresholdIndicates the number errors monitored before declaring
the interface down.rw INTEGER .wfFrSwDlcmiTable.1.11 |
wfFrSwDlcmiMonitoredEventsIndicates the events over which error threshold is kept.rw INTEGER .wfFrSwDlcmiTable.1.12 |
wfFrSwDlcmiRecoveryCountsIndicates the number of correct polling
cycles during recovery.ro INTEGER .wfFrSwDlcmiTable.1.13 |
wfFrSwDlcmiMaxSupportedVCsIndicates the maximum number of VCs allowed.rw INTEGER .wfFrSwDlcmiTable.1.14 |
wfFrSwDlcmiVCsInUseIndicates the number of VCs that are currently
configured on this interface.ro INTEGER .wfFrSwDlcmiTable.1.15 |
wfFrSwSwitchHdrErrorsIndicates the number of frames dropped because they were
received on the remote side with an invalid switch header.ro Counter .wfFrSwDlcmiTable.1.16 |
wfFrSwDlcmiSequenceCountIndicates this switch's sequence counter; value of
next to send.ro INTEGER .wfFrSwDlcmiTable.1.17 |
wfFrSwDlcmiLastReceivedIndicates the sequence number just received from
the end station.ro INTEGER .wfFrSwDlcmiTable.1.18 |
wfFrSwDlcmiActiveSeqCountIndicates the switch's sequence counter for sending
status enquiry. (For bidirectional procedures.)ro INTEGER .wfFrSwDlcmiTable.1.19 |
wfFrSwDlcmiActiveReceivedIndicates the sequence number just received from the
enquiring station. (For bidirectional procedures.)ro INTEGER .wfFrSwDlcmiTable.1.20 |
wfFrSwDlcmiPollsThis is the counter of where we are in the polling cycle.ro Counter .wfFrSwDlcmiTable.1.21 |
wfFrSwDlcmiAlarmTimerCounter of 1/2 second timeouts. Indicates
when to expect poll.ro INTEGER .wfFrSwDlcmiTable.1.22 |
wfFrSwErrTypeIndicates the type of the last specific monitored error.ro Enumeration .wfFrSwDlcmiTable.1.23 |
wfFrSwErrDataContains as much of the error packet as possible.ro OCTET STRING .wfFrSwDlcmiTable.1.24 |
wfFrSwErrTimeIndicates the time the last error occurred.ro TimeTicks (SNMPv2-SMI) .wfFrSwDlcmiTable.1.25 |
wfFrSwBcMeasurementIntervalIndicates the Committed Burst sample window interval in msecrw INTEGER .wfFrSwDlcmiTable.1.26 |
wfFrSwDlcmiMcastNoBufferErrorsIndicates the number of times a multicast failed partially
or wholly because there are insufficient buffers available
to create multiple copies of a multicast framero Counter .wfFrSwDlcmiTable.1.27 |
wfFrSwDlcmiFrameTooShortErrorsIndicates the number of frames dropped that
are too short to be accepted.ro Counter .wfFrSwDlcmiTable.1.28 |
wfFrSwDlcmiFrameTooLongErrorsIndicates the number of frames dropped that
are too long to be accepted.ro Counter .wfFrSwDlcmiTable.1.29 |
wfFrSwDlcmiIllegalDlciErrorsIndicates the number of frames dropped that
had an invalid DLCI value.ro Counter .wfFrSwDlcmiTable.1.30 |
wfFrSwDlcmiUnknownDlciErrorsIndicates the number of frames dropped which
had an unknown DLCI value.ro Counter .wfFrSwDlcmiTable.1.31 |
wfFrSwDlcmiProtocolErrorsIndicates the number of frames dropped because
of a DLCMI protocol violation.ro Counter .wfFrSwDlcmiTable.1.32 |
wfFrSwDlcmiUnknownIEErrorsIndicates the number of frames dropped that
had an unknown information element.ro Counter .wfFrSwDlcmiTable.1.33 |
wfFrSwDlcmiSequenceErrorsIndicates the number of frames dropped because
of a DLCMI sequence error.ro Counter .wfFrSwDlcmiTable.1.34 |
wfFrSwDlcmiUnknownRPTErrorsIndicates the number of frames dropped which
had an unknown report type.ro Counter .wfFrSwDlcmiTable.1.35 |
wfFrSwDlcmiControlByteErrorsIndicates the number of frames dropped that
had an unsupported control byte.ro Counter .wfFrSwDlcmiTable.1.36 |
wfFrSwDlcmiFormatErrorsIndicates the number of frames dropped due to
a frame format error.ro Counter .wfFrSwDlcmiTable.1.37 |
wfFrSwDlcmiOtherErrorsIndicates the number of frames dropped due to unknown
or other errors not counted by any error counter.ro Counter .wfFrSwDlcmiTable.1.38 |
wfFrSwDlcmiStatusIndicates which state of execution the DLCMI gate is inro Enumeration .wfFrSwDlcmiTable.1.39 |
wfFrSwDlcmiNewVCsIndicates the number of newly added PVCs that we have not yet told the
CPE about, by means of a full-status message.ro Counter .wfFrSwDlcmiTable.1.40 |
wfFrSwDlcmiDeletedVCsIndicates the number of deletedly added PVCs that we have not yet told the
CPE about, by means of a full-status message.ro Counter .wfFrSwDlcmiTable.1.41 |
wfFrSwDlcmiFullStatusSeqIndicates the expected sequence number for the next Status Enquiry
message that will prove that the CPE received our last Full Status
Message and knows about the deleted PVCs.ro Counter .wfFrSwDlcmiTable.1.42 |
wfFrSwDlcmiBidirectIndication to delete this frame relay interface.rw Enumeration .wfFrSwDlcmiTable.1.43 |
wfFrSwDlcmiDteStatusIndicates which state of execution the DLCMI gate is in for
bidirectional procedures.ro Enumeration .wfFrSwDlcmiTable.1.44 |
wfFrSwDlcmiDteSeqCountIndicates the switch's sequence counter for sending
status enquiry. (For bidirectional procedures.)ro INTEGER .wfFrSwDlcmiTable.1.45 |
wfFrSwDlcmiDteReceivedIndicates the sequence number just received from the
enquiring station. (For bidirectional procedures.)ro INTEGER .wfFrSwDlcmiTable.1.46 |
wfFrSwDlcmiDteLastReceivedIndicates the sequence number just received from
the end station.ro INTEGER .wfFrSwDlcmiTable.1.47 |
wfFrSwDlcmiDtePollsThis is the counter of where we are in the polling cycle.ro Counter .wfFrSwDlcmiTable.1.48 |
wfFrSwDlcmiDtePollingIntervalThe number of seconds between successive status enquiry
messages.rw INTEGER .wfFrSwDlcmiTable.1.49 |
wfFrSwDlcmiDteFullEnquiryIntervalIndicates the number of status enquiries before a full
status enquiry. (For bidirectional procedures.)rw INTEGER .wfFrSwDlcmiTable.1.50 |
wfFrSwDlcmiDteErrorThresholdIndicates the number errors monitored before declaring
the interface down.rw INTEGER .wfFrSwDlcmiTable.1.51 |
wfFrSwDlcmiCrossNetEnableIndication to delete this frame relay interface.rw Enumeration .wfFrSwDlcmiTable.1.52 |
wfFrSwDlcmiCrossNetPollingIntervalThe number of seconds between successive status enquiry
messages.rw INTEGER .wfFrSwDlcmiTable.1.53 |
wfFrSwDlcmiCrossNetErrorThresholdIndicates the number missed heartbeat polls before
declaring the cross-net PVC inactive.rw INTEGER .wfFrSwDlcmiTable.1.54 |
wfFrSwDlcmiCrossNetAsyncUpdateEnableIndicates whether we are to send to the other end
of the network, status updates for dlcis as soon as
there is a change of status for the dlci.rw Enumeration .wfFrSwDlcmiTable.1.55 |
wfFrSwDlcmiBcMeasurementEnableIndicates whether Committed Burst Measurement is enabled
for this interface. If this attribute is set to DISABLE then
DE bit setting in Frame Relay frames at this interface is disabled.rw Enumeration .wfFrSwDlcmiTable.1.56 |
wfFrSwDlcmiAsyncUpdateEnableIndicates whether the link management entity should
send an asynchronous single PVC update message
when the state of a PVC is changed by a technician
or by cross-net polling procedures.rw Enumeration .wfFrSwDlcmiTable.1.57 |
wfFrSwDlcmiCrossNetListenEnableIndicates whether the link management entity should
make a judgement of the PVC's status based on Cross
Net updates.rw Enumeration .wfFrSwDlcmiTable.1.58 |
wfFrSwDlcmiSvcDisableIndicates whether SVC is enabled or disabled for this access
channel.rw Enumeration .wfFrSwDlcmiTable.1.59 |
wfFrSwDlcmiL2AddrTypeIndicates the address type supported on this access
channel. This information is needed when wFrSwDlcmiSVCDisable
is enabled.rw Enumeration .wfFrSwDlcmiTable.1.60 |
wfFrSwDlcmiEscapeModeIdentifies the Escape mode (none, ingress or egress) to be used for
PVCs with wfFrSwVcEscapeMode set to enabled.rw Enumeration .wfFrSwDlcmiTable.1.61 |
wfFrSwDlcmiEscapeCircuitIdentifies the FR-DTE circuit number corresponding to an Escape PVC.
Applies only to PVCs with wfFrSwVcEscapeEnable set to enabled.rw INTEGER .wfFrSwDlcmiTable.1.62 |
wfFrSwDlcmiEscapeVcCountThe number of PVCs on this DLCMI that are configured as
Escape VCsrw INTEGER .wfFrSwDlcmiTable.1.63 |
wfFrSwDlcmiIwfModeIdentifies the interworking mode (none, SDLC-to-FRSW) to be used for
PVCs with wfFrSwVcEscapeMode set to enabled.rw Enumeration .wfFrSwDlcmiTable.1.64 |
wfFrSwDlcmiSvcBillingEnableIndicates whether the SVC Billing on this access
channel set to enable.rw Enumeration .wfFrSwDlcmiTable.1.65 |
wfFrSwDlcmiSpvcAgentIndicates if an SPVC Call Request Agent, Call Accept
Agent, or both are enabled on this FRSW circuit.rw Enumeration .wfFrSwDlcmiTable.1.66 |
wfFrSwDlcmiCallAccDlciSelectionTypeIndicates to the Call Accept Agent to accept SPVC Call Setup
requests for any available DLCI or for a specific DLCI. Call
Setup requests with the wrong selection type will be rejected.rw Enumeration .wfFrSwDlcmiTable.1.67 |