Wellfleet-WCP-MIB
Detailed view of the defined objects, syntax rules, and hierarchical paths.
142
Objects
Active
Status
3
Dependencies
Imported Objects
Objects
142 total| Object Name |
|---|
RFC1155-SMIThe line table contains line entries. SEQUENCE OF WfWcpLineEntry .1.3.6.1.4.1.18.3.4.22.1 |
wfWcpCircuitTableThe circuit table contains circuit entries. SEQUENCE OF WfWcpCircuitEntry .1.3.6.1.4.1.18.3.4.22.2 |
wfWcpCircuitEntryThe components of the instance ID of a circuit entry. WfWcpCircuitEntry .1.3.6.1.4.1.18.3.4.22.2.1 |
wfWcpCircuitDeleteIndicates whether the instance have been created or deleted.rw Enumeration .1.3.6.1.4.1.18.3.4.22.2.1.1 |
wfWcpCircuitDisableIndicates whether the instance have been enabled or disabled.rw Enumeration .1.3.6.1.4.1.18.3.4.22.2.1.2 |
wfWcpCircuitIdIndicates the circuit ID of this entry.ro INTEGER .1.3.6.1.4.1.18.3.4.22.2.1.3 |
wfWcpCircuitCompressionModesuitable when the line is relatively noisy.rw Enumeration .1.3.6.1.4.1.18.3.4.22.2.1.4 |
wfWcpCircuitHistorySizecircuit.rw Enumeration .1.3.6.1.4.1.18.3.4.22.2.1.5 |
wfWcpCircuitEngineTypeIndicates whether to use hardware or software compressionrw Enumeration .1.3.6.1.4.1.18.3.4.22.2.1.6 |
wfWcpCircuitSearchDepthThis attribute is only relevant for HW Compression VCs
configured for CPC, 8K history. It indicates the Search
Depth configured for this circuit. Increasing this attribute
may allow the user to achieve better Compression ratios.
This however could occur at the expense of throughput
(i.e. you may get better compression ratios, but lower
throughput). Note that this value may be set to 0, if the
user wishes to run this circuit in High Speed mode.
Note that the default value of 256 is actually used to
indicate that that this attribute should be inherited from
wfWcpLineEntry MIB & is not a valid search depth value.
Valid Search Depth values lie within the 1..255 range.rw INTEGER .1.3.6.1.4.1.18.3.4.22.2.1.7 |
wfWcpCircuitCompressorOutBytesIndicates the number of bytes produced by the compressor.ro Counter .1.3.6.1.4.1.18.3.4.22.2.1.8 |
wfWcpCircuitDecompressorOutBytesIndicates the number of bytes produced by the decompressor.ro Counter .1.3.6.1.4.1.18.3.4.22.2.1.9 |
wfWcpVcTableThe VC table contains VC entries SEQUENCE OF WfWcpVcEntry .1.3.6.1.4.1.18.3.4.22.3 |
wfWcpVcEntryThe components of the instance ID of a VC entry. WfWcpVcEntry .1.3.6.1.4.1.18.3.4.22.3.1 |
wfWcpVcCompressorStateIndicates the VC compressor state of the WCP logical connection.ro Enumeration .1.3.6.1.4.1.18.3.4.22.3.1.1 |
wfWcpVcDecompressorStateIndicates the VC decompressor state of the WCP logical connection.ro Enumeration .1.3.6.1.4.1.18.3.4.22.3.1.2 |
wfWcpVcLineNumberinstance ID.ro INTEGER .1.3.6.1.4.1.18.3.4.22.3.1.3 |
wfWcpVcLLIndexinstance ID.ro INTEGER .1.3.6.1.4.1.18.3.4.22.3.1.4 |
wfWcpVcCircuitIdID.ro INTEGER .1.3.6.1.4.1.18.3.4.22.3.1.5 |
wfWcpVcIdIndicates the ID of this VC entry. This is part of the instance ID.ro INTEGER .1.3.6.1.4.1.18.3.4.22.3.1.6 |
wfWcpVcCompressionModeline is relatively noisy.ro Enumeration .1.3.6.1.4.1.18.3.4.22.3.1.7 |
wfWcpVcHistorySizeVC. HIGH will allow the highest compression ratio to be realized.ro Enumeration .1.3.6.1.4.1.18.3.4.22.3.1.8 |
wfWcpVcCompressorInBytesIndicates the number of bytes submitted to the compressor.ro Counter .1.3.6.1.4.1.18.3.4.22.3.1.9 |
wfWcpVcCompressorOutBytesIndicates the number of bytes produced by the compressor.ro Counter .1.3.6.1.4.1.18.3.4.22.3.1.10 |
wfWcpVcDecompressorInBytesIndicates the number of bytes submitted to the decompressor.ro Counter .1.3.6.1.4.1.18.3.4.22.3.1.11 |
wfWcpVcDecompressorOutBytesIndicates the number of bytes produced by the decompressor.ro Counter .1.3.6.1.4.1.18.3.4.22.3.1.12 |
wfWcpVcTxCPCPacketsIndicates the number of continuous mode packets sent.ro Counter .1.3.6.1.4.1.18.3.4.22.3.1.13 |
wfWcpVcRxCPCPacketsIndicates the number of continuous mode packets received.ro Counter .1.3.6.1.4.1.18.3.4.22.3.1.14 |
wfWcpVcTxPPCPacketsIndicates the number of PPC mode packets sent.ro Counter .1.3.6.1.4.1.18.3.4.22.3.1.15 |
wfWcpVcRxPPCPacketsIndicates the number of PPC mode packets Received.ro Counter .1.3.6.1.4.1.18.3.4.22.3.1.16 |
wfWcpVcTxAntiExpPacketsIndicates the number of anti-expanded packets sent.ro Counter .1.3.6.1.4.1.18.3.4.22.3.1.17 |
wfWcpVcRxAntiExpPacketsIndicates the number of anti-expanded packets received.ro Counter .1.3.6.1.4.1.18.3.4.22.3.1.18 |
wfWcpVcTxResetReqsIndicates the number of reset request sent.ro Counter .1.3.6.1.4.1.18.3.4.22.3.1.19 |
wfWcpVcRxResetReqsIndicates the number of reset request received.ro Counter .1.3.6.1.4.1.18.3.4.22.3.1.20 |
wfWcpVcTxRexmitReqsIndicates the number of re-transmit request sent.ro Counter .1.3.6.1.4.1.18.3.4.22.3.1.21 |
wfWcpVcRxRexmitReqsIndicates the number of re-transmit request received.ro Counter .1.3.6.1.4.1.18.3.4.22.3.1.22 |
wfWcpVcTxRexmitNaksIndicates the number of re-transmit Nak sent.ro Counter .1.3.6.1.4.1.18.3.4.22.3.1.23 |
wfWcpVcRxRexmitNaksIndicates the number of re-transmit Nak received.ro Counter .1.3.6.1.4.1.18.3.4.22.3.1.24 |
wfWcpVcDataOutOfSeqsIndicates the number of times that a data indication is out of sequence.ro Counter .1.3.6.1.4.1.18.3.4.22.3.1.25 |
wfWcpVcRexmitOutOfSeqsIndicates the number of times that a re-transmit Ack is out of sequence.ro Counter .1.3.6.1.4.1.18.3.4.22.3.1.26 |
wfWcpVcRexmitTimeoutsIndicates the number of re-transmit timeout.ro Counter .1.3.6.1.4.1.18.3.4.22.3.1.27 |
wfWcpVcExceededKsIndicates the number of times that K is exceeded.ro Counter .1.3.6.1.4.1.18.3.4.22.3.1.28 |
wfWcpVcInvalidOpCodesIndicates the number of packets received with invalid op code.ro Counter .1.3.6.1.4.1.18.3.4.22.3.1.29 |
wfWcpVcEngineTypeIndicates whether hardware or software compression is usedro Enumeration .1.3.6.1.4.1.18.3.4.22.3.1.30 |
wfWcpVcSearchDepthThis attribute is only relevant for HW Compression VCs
configured for CPC, 8K history. It indicates the Search
Depth configured for this VC. Increasing this attribute
may allow the user to achieve better Compression ratios.
This however could occur at the expense of throughput
(i.e. you may get better compression ratios, but lower
throughput). Note that this value may be 0, if the user
wishes to run their VC in High Speed Mode.ro INTEGER .1.3.6.1.4.1.18.3.4.22.3.1.31 |
wfHwCompTableThe HW Compression Table contains compression entries. SEQUENCE OF WfHwCompEntry .1.3.6.1.4.1.18.3.4.22.4 |
wfHwCompEntrySlot number used as instance identifier. WfHwCompEntry .1.3.6.1.4.1.18.3.4.22.4.1 |
wfHwCompStateDriver state variable.ro Enumeration .1.3.6.1.4.1.18.3.4.22.4.1.1 |
wfHwCompSlotSlot number
::= { wfHwCompEntry 2 }
wfHwCompModule OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTIONro INTEGER .1.3.6.1.4.1.18.3.4.22.4.1.3 |
wfHwCompEngineNumberCompression Engine #. Gotten from the instance ID.ro INTEGER .1.3.6.1.4.1.18.3.4.22.4.1.4 |
wfHwCompCompressionHistoryTotalThe amount of memory allocated for Compression History.ro INTEGER .1.3.6.1.4.1.18.3.4.22.4.1.5 |
wfHwCompCompressionHashTblSizeThe amount of memory allocated for Compression Hash Tables.
These Hash Tables are used to do lookups in Compression
History memory.ro INTEGER .1.3.6.1.4.1.18.3.4.22.4.1.6 |
wfHwCompDecompressionHistoryTotalThe amount of memory allocated for Decompression History.ro INTEGER .1.3.6.1.4.1.18.3.4.22.4.1.7 |
wfHwComp8kContextsTotalThis indicates the maximum number of 8KB Context Control Blocks (CCBs)
(i.e. VC's) we can support with this memory configuration. This is
assuming ALL VC's using Variable Search Depth Mode, 8KB
history size. This equals wfHwCompCompressionHistoryTotal
divided by 8KB.ro INTEGER .1.3.6.1.4.1.18.3.4.22.4.1.8 |
wfHwComp32kContextsTotalThis indicates the maximum number of 32KB Context Control Blocks (CCBs)
(i.e. VC's) we can support with this memory configuration. This is
assuming ALL VC's using High Speed, Single Search Mode, 32KB
history size. This equals wfHwCompCompressionHistoryTotal
divided by 32KB.ro INTEGER .1.3.6.1.4.1.18.3.4.22.4.1.9 |
wfHwComp8kCpcContextsInUseThis indicates the current number of 8KB CPC (Continuous
Packet Compression) Mode VC's using Hardware Compression
services.ro INTEGER .1.3.6.1.4.1.18.3.4.22.4.1.10 |
wfHwComp8kPpcContextsInUseThis indicates the number of PPC (Per Packet Compression)
Mode VC's allocated for HW Compression. This value ALWAYS
equates to 1, as 1 PPC Context is ALWAYS reserved as a
resource for any VC doing HW Compression to use.
All VC's configured to run in PPC Mode share this context.
This context is also used when a VC enters Transient PPC
Compression Mode, which occurs when frames are dropped
or errors occur on the physical link.ro INTEGER .1.3.6.1.4.1.18.3.4.22.4.1.11 |
wfHwComp32kContextsInUseThis indicates the current number of 32KB Context Control Blocks (CCBs)
(i.e. VC's) using Hardware Compression services.ro INTEGER .1.3.6.1.4.1.18.3.4.22.4.1.12 |
wfHwComp8kContextsAvailableThis indicates the number of 'usable' 8k Context Control Blocks available.
Note that this will get reduced (by 4) when a user configures a VC for
32KB History Size (i.e. High Speed, Single Search Mode).ro INTEGER .1.3.6.1.4.1.18.3.4.22.4.1.13 |
wfHwComp32kContextsAvailableThis indicates the number of 'usable' 32k Context Control Blocks
available. This means that this/these number of pages of Compression
Memory currently have NO Context Control Block (i.e.VC) associated
with them.ro INTEGER .1.3.6.1.4.1.18.3.4.22.4.1.14 |
wfHwCompCpcContextsRegisteredThis indicates the number of VC's which have registered for
HW Compression and are using Continuous Packet Compression
(CPC) mode. Anytime a VC/Context successfully registers with
HW Compression using this mode, a HW context has been
dedicated to that VC.ro INTEGER .1.3.6.1.4.1.18.3.4.22.4.1.15 |
wfHwCompPpcContextsRegisteredThis indicates the number of VC's which have registered
for HW Compression and are using Packet by Packet Compression
(PPC) mode. All VCs/Contexts which register using PPC mode,
share 1 HW Context which has been dedicated for use by PPC
Vcs.ro INTEGER .1.3.6.1.4.1.18.3.4.22.4.1.16 |
wfHwCompCompressionTotalRingSizeThis indicates the total number of Descriptor ring entries
available for HW Compression.ro INTEGER .1.3.6.1.4.1.18.3.4.22.4.1.17 |
wfHwCompDecompressionTotalRingSizeThis indicates the total number of Descriptor ring entries
available for HW Decompression.ro INTEGER .1.3.6.1.4.1.18.3.4.22.4.1.18 |
wfHwCompCompressionCurrentQueuedThis is a snapshot of the current number of entries
outstanding on the HW Compression Ring.ro INTEGER .1.3.6.1.4.1.18.3.4.22.4.1.19 |
wfHwCompDecompressionCurrentQueuedThis is a snapshot of the current number of entries
outstanding on the HW Decompression Ring.ro INTEGER .1.3.6.1.4.1.18.3.4.22.4.1.20 |
wfHwCompCompressionQHiWatermarkThis indicates the largest number of frames ever
outstanding on the HW Compression Ring since this
Compression Engine started providing HW Compression
services.ro INTEGER .1.3.6.1.4.1.18.3.4.22.4.1.21 |
wfHwCompDecompressionQHiWatermarkThis indicates the largest number of frames ever
outstanding on the HW Decompression Ring since this
Compression Engine started providing HW Compression
services.ro INTEGER .1.3.6.1.4.1.18.3.4.22.4.1.22 |
wfHwCompCompressionPktsThe # of pkts successfully compressed.ro Counter .1.3.6.1.4.1.18.3.4.22.4.1.23 |
wfHwCompDecompressionPktsThe # of pkts successfully decompressed.ro Counter .1.3.6.1.4.1.18.3.4.22.4.1.24 |
wfHwCompTxExpandedPktsThe # of pkts given to the Compressor which actually expanded
instead of compressing.ro Counter .1.3.6.1.4.1.18.3.4.22.4.1.25 |
wfHwCompTxNonCompressedPktsThis indicates a temporary Buffer Starvation condition.
When we cannot get a buffer to Compress into, this stat
gets incremented & the original UnCompressed frame is sent.ro Counter .1.3.6.1.4.1.18.3.4.22.4.1.26 |
wfHwCompRxNonCompressedPktsThe # of pkts received across the link which happened to
come across the link uncompressed. This can be either
because the pkt was an Expanded pkt at the remote end or
for some reason the sending device could not compress this
particular pkt due to resource issues.ro Counter .1.3.6.1.4.1.18.3.4.22.4.1.27 |
wfHwCompRxDroppedPktsThis indicates a temporary Buffer Starvation condition.
When we cannot get a buffer to Decompress into, this stat
gets incremented & the received Compressed data frame is
run through the Decompressor in order to update the
Decompressors histories and then dropped.ro Counter .1.3.6.1.4.1.18.3.4.22.4.1.28 |
wfHwCompRxLcbMismatchesThis indicates a frame was dropped between the remote
end and this end. Line errors such as CRC Errors cause
this. Buffer starvation in this router can also cause this.ro Counter .1.3.6.1.4.1.18.3.4.22.4.1.29 |
wfHwCompCompressionRingOverflowsNumber of frames dropped due to Compression Descriptor
Ring full condition.ro Counter .1.3.6.1.4.1.18.3.4.22.4.1.30 |
wfHwCompDecompressionRingOverflowsNumber of frames dropped due to Decompression Descriptor
Ring full condition.ro Counter .1.3.6.1.4.1.18.3.4.22.4.1.31 |
wfHwCompCompressionErrorsIndicates the total # of Compression Errors detected on this module.ro Counter .1.3.6.1.4.1.18.3.4.22.4.1.32 |
wfHwCompDecompressionErrorsIndicates the total # of Decompression Errors detected on this module.ro Counter .1.3.6.1.4.1.18.3.4.22.4.1.33 |
wfHwCompCompressionSrcPktLenErrorsA zero length source packet was received by the Compressor or
Decompressor.ro Counter .1.3.6.1.4.1.18.3.4.22.4.1.34 |
wfHwCompCompressionCcbFormatErrorsThe format of the specified Context Control Block (CCB) was detected to be
in error.ro Counter .1.3.6.1.4.1.18.3.4.22.4.1.35 |
wfHwCompCompressionDescFormatErrorsThe format of the current descriptor is in error.ro Counter .1.3.6.1.4.1.18.3.4.22.4.1.36 |
wfHwCompCompressionInternalErrorsThe Compressor or Decompressor took an internal error when processing
this descriptor.ro Counter .1.3.6.1.4.1.18.3.4.22.4.1.37 |
wfHwCompDecompressionSrcPktLenErrorsA zero length source packet was received by the Compressor or
Decompressor.ro Counter .1.3.6.1.4.1.18.3.4.22.4.1.38 |
wfHwCompDecompressionCcbFormatErrorsThe format of the specified Context Control Block (CCB) was detected to be
in error.ro Counter .1.3.6.1.4.1.18.3.4.22.4.1.39 |
wfHwCompDecompressionDescFormatErrorsThe format of the current descriptor is in error.ro Counter .1.3.6.1.4.1.18.3.4.22.4.1.40 |
wfHwCompDecompressionInternalErrorsThe Compressor or Decompressor took an internal error when processing
this descriptor.ro Counter .1.3.6.1.4.1.18.3.4.22.4.1.41 |
wfHwCompChipTypeCompression Chip Type: MAGNALINK or ITCSro Enumeration .1.3.6.1.4.1.18.3.4.22.4.1.42 |
wfHwCompMsaCpcContextsRegisteredThe number of MSA VC's which have registered for
HW Compression and are using Continuous Packet Compression
(CPC) mode. Anytime an MSA VC/Context successfully registers with
HW Compression using this mode, a HW context has been
dedicated to that VC.ro INTEGER .1.3.6.1.4.1.18.3.4.22.4.1.43 |
wfHwCompMsaPpcContextsRegisteredThe number of MSA VC's which have registered
for HW Compression and are using Packet by Packet Compression
(PPC) mode. All MSA VCs/Contexts which register using PPC mode,
share 1 HW Context which has been dedicated for use by PPC
Vcs.ro INTEGER .1.3.6.1.4.1.18.3.4.22.4.1.44 |
wfHwCompMsa8KContextsGuaranteedThe number of 8K MSA contexts reserved with
a particular memory carving. Calculated as number of pages
guaranteed for MSA times 4, where 4 is the maximum number
of 8K MSA contexts per page.ro INTEGER .1.3.6.1.4.1.18.3.4.22.4.1.45 |
wfHwCompStacContextsTotalThe maximum number of STAC CCBs that can be
supported for a particular memory carving.ro INTEGER .1.3.6.1.4.1.18.3.4.22.4.1.46 |
wfHwCompStacCpcContextsRegisteredThis indicates the number of STAC VC's which have registered for
HW Compression and are using Continuous Packet Compression
(CPC) mode. Anytime a STAC VC/Context successfully registers with
HW Compression using this mode, a HW context has been
dedicated to that VC.ro INTEGER .1.3.6.1.4.1.18.3.4.22.4.1.47 |
wfHwCompStacPpcContextsRegisteredThe number of STAC VC's which have registered
for HW Compression and are using Packet by Packet Compression
(PPC) mode. All STAC VCs/Contexts which register using PPC mode,
share 1 HW Context which has been dedicated for use by PPC
Vcs.ro INTEGER .1.3.6.1.4.1.18.3.4.22.4.1.48 |
wfHwCompStacPpcContextsInUseThe number of STAC contexts allocated for PPC.
Equals 1 if STAC is enabled, 0 if it is disabled.ro INTEGER .1.3.6.1.4.1.18.3.4.22.4.1.49 |
wfHwCompStacContextsAvailableThe number of 'usable' STAC context control blocks
available.ro INTEGER .1.3.6.1.4.1.18.3.4.22.4.1.50 |
wfHwCompStacContextsGuaranteedThe number of STAC contexts reserved with
a particular memory carving. Calculated as number of pages
guaranteed for STAC times 8, where 8 is the maximum number
of STAC contexts per page.ro INTEGER .1.3.6.1.4.1.18.3.4.22.4.1.51 |
wfHwCompMsaCompressedPktsThe # of pkts successfully compressed using MSA compression algorithm.ro Counter .1.3.6.1.4.1.18.3.4.22.4.1.52 |
wfHwCompStacCompressedPktsThe # of pkts successfully compressed using STAC compression algorithm.ro Counter .1.3.6.1.4.1.18.3.4.22.4.1.53 |
wfHwCompMsaDecompressedPktsThe # of pkts successfully decompressed using MSA compression algorithm.ro Counter .1.3.6.1.4.1.18.3.4.22.4.1.54 |
wfHwCompStacDecompressedPktsThe # of pkts successfully decompressed using STAC compression algorithm.ro Counter .1.3.6.1.4.1.18.3.4.22.4.1.55 |
wfHwCompMsaTxExpandedPktsThe # of pkts given to the Compressor which actually expanded
instead of compressing using MSA compression algorithm.ro Counter .1.3.6.1.4.1.18.3.4.22.4.1.56 |
wfHwCompStacTxExpandedPktsThe # of pkts given to the Compressor which actually expanded
instead of compressing using STAC compression algorithm.ro Counter .1.3.6.1.4.1.18.3.4.22.4.1.57 |
wfHwCompMsaTxNonCompressedPktsThis indicates a temporary Buffer Starvation condition.
When we cannot get a buffer to Compress into, this stat
gets incremented & the original UnCompressed frame is sent.ro Counter .1.3.6.1.4.1.18.3.4.22.4.1.58 |
wfHwCompStacTxNonCompressedPktsThis indicates a temporary Buffer Starvation condition.
When we cannot get a buffer to Compress into, this stat
gets incremented & the original UnCompressed frame is sent.ro Counter .1.3.6.1.4.1.18.3.4.22.4.1.59 |
wfHwCompMsaRxNonCompressedPktsThe # of pkts received across the link which happened to
come across the link uncompressed. This can be either
because the pkt was an Expanded pkt at the remote end or
for some reason the sending device could not compress this
particular pkt due to resource issues.ro Counter .1.3.6.1.4.1.18.3.4.22.4.1.60 |
wfHwCompStacRxNonCompressedPktsThe # of pkts received across the link which happened to
come across the link uncompressed. This can be either
because the pkt was an Expanded pkt at the remote end or
for some reason the sending device could not compress this
particular pkt due to resource issues.ro Counter .1.3.6.1.4.1.18.3.4.22.4.1.61 |
wfStacCircuitTableThe circuit table contains circuit entries. SEQUENCE OF WfStacCircuitEntry .1.3.6.1.4.1.18.3.4.22.6 |
wfStacCircuitEntryThe components of the instance ID of a circuit entry. WfStacCircuitEntry .1.3.6.1.4.1.18.3.4.22.6.1 |
wfStacCircuitDeleteIndication to delete this Stac LZS/PPP interfacerw Enumeration .1.3.6.1.4.1.18.3.4.22.6.1.1 |
wfStacCircuitDisableUsed to enable and disable compression.rw Enumeration .1.3.6.1.4.1.18.3.4.22.6.1.2 |
wfStacCircuitIdIndicates the circuit ID of this entry.rw INTEGER .1.3.6.1.4.1.18.3.4.22.6.1.3 |
wfStacCircuitEngineTypeIndicates whether to use hardware or software compressionrw Enumeration .1.3.6.1.4.1.18.3.4.22.6.1.4 |
wfStacCircuitCompressionModeIndicates the check mode. See RFC 1974.rw Enumeration .1.3.6.1.4.1.18.3.4.22.6.1.5 |
wfStacCircuitCompressorStateIndicates the compressor state of this circuit entry.ro Enumeration .1.3.6.1.4.1.18.3.4.22.6.1.6 |
wfStacCircuitDecompressorStateIndicates the decompressor state of this circuit entry.ro Enumeration .1.3.6.1.4.1.18.3.4.22.6.1.7 |
wfStacCircuitFallBackCompressionModeThis attribute is only relevant when any the circuit on
that line is unable to register for HW Compression due
to a lack of physical HW Context memory (Note that only
HW CPC contexts can fail registration in this way).rw Enumeration .1.3.6.1.4.1.18.3.4.22.6.1.8 |
wfStacCircuitCompressorInBytesIndicates the number of bytes submitted to the compressor.ro Counter .1.3.6.1.4.1.18.3.4.22.6.1.9 |
wfStacCircuitCompressorOutBytesIndicates the number of bytes produced by the compressor.ro Counter .1.3.6.1.4.1.18.3.4.22.6.1.10 |
wfStacCircuitDecompressorInBytesIndicates the number of bytes submitted to the decompressor.ro Counter .1.3.6.1.4.1.18.3.4.22.6.1.11 |
wfStacCircuitDecompressorOutBytesIndicates the number of bytes produced by the decompressor.ro Counter .1.3.6.1.4.1.18.3.4.22.6.1.12 |
wfStacCircuitTxMode0PacketsIndicates the number of mode 0 packets sent.ro Counter .1.3.6.1.4.1.18.3.4.22.6.1.13 |
wfStacCircuitRxMode0PacketsIndicates the number of mode 0 packets received.ro Counter .1.3.6.1.4.1.18.3.4.22.6.1.14 |
wfStacCircuitTxMode3PacketsIndicates the number of mode 3 packets sent.ro Counter .1.3.6.1.4.1.18.3.4.22.6.1.15 |
wfStacCircuitRxMode3PacketsIndicates the number of mode 3 packets received.ro Counter .1.3.6.1.4.1.18.3.4.22.6.1.16 |
wfStacCircuitTxExpPacketsIndicates the number of expanded packets sent.ro Counter .1.3.6.1.4.1.18.3.4.22.6.1.17 |
wfStacCircuitRxExpPacketsIndicates the number of expanded packets received.ro Counter .1.3.6.1.4.1.18.3.4.22.6.1.18 |
wfStacCircuitTxResetReqsIndicates the number of reset requests sent.ro Counter .1.3.6.1.4.1.18.3.4.22.6.1.19 |
wfStacCircuitRxResetReqsIndicates the number of reset requests received.ro Counter .1.3.6.1.4.1.18.3.4.22.6.1.20 |
wfWcpLineEntryThe components of the instance ID of a line entry. WfWcpLineEntry .wfWcpLineTable.1 |
wfWcpLineDeleteIndicates whether the instance have been created or deleted.rw Enumeration .wfWcpLineTable.1.1 |
wfWcpLineDisableIndicates whether the instance have been enabled or disabled.rw Enumeration .wfWcpLineTable.1.2 |
wfWcpLineLineNumberinstance ID.ro INTEGER .wfWcpLineTable.1.3 |
wfWcpLineLLIndexinstance ID.ro INTEGER .wfWcpLineTable.1.4 |
wfWcpLineCompressionModeline is relatively noisy.rw Enumeration .wfWcpLineTable.1.5 |
wfWcpLineHistorySizeline.rw Enumeration .wfWcpLineTable.1.6 |
wfWcpLineBufferSizeused.rw Enumeration .wfWcpLineTable.1.7 |
wfWcpLineEngineTypeIndicates whether to use hardware or software compressionrw Enumeration .wfWcpLineTable.1.8 |
wfWcpLineSearchDepthThis attribute is only relevant for HW Compression VCs
configured for CPC, 8K history. It indicates the Search
Depth configured for this line. Increasing this attribute
may allow the user to achieve better Compression ratios.
This however could occur at the expense of throughput
(i.e. you may get better compression ratios, but lower
throughput). Note that this value may be set to 0, if the
user wishes to run their Line in High Speed mode.rw INTEGER .wfWcpLineTable.1.9 |
wfWcpLineFallbackCompressionModeThis attribute is only relevant for HW Compression VCs
configured for CPC. It indicates what Compression Mode
the user wants All VCs on a line to use, when any VC on
that line is unable to register for HW Compression due
to a lack of physical HW Context memory (Note that only
HW CPC contexts can fail registration in this way).rw Enumeration .wfWcpLineTable.1.10 |
wfWcpLineClientCompressorRingSizeSpecifies the client compressor ring size for clients
of this line. The default value is ZERO which will cause
the hardware compression to assign the hard coded default
value.rw INTEGER .wfWcpLineTable.1.11 |
wfWcpLineClientDecompressorRingSizeSpecifies the client decompressor ring size for clients
of this line. The default value is ZERO which will cause
the hardware compression to assign the hard coded default
value.rw INTEGER .wfWcpLineTable.1.12 |