Wellfleet-NAT-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for Wellfleet-NAT-MIB.
146
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
146 total| Object Name |
|---|
wfNatBase OBJECT IDENTIFIER .1.3.6.1.4.1.18.3.5.3.2.7.1 |
RFC1155-SMI Unknown .1.3.6.1.4.1.18.3.5.3.2.7.1 |
wfNatBaseDelete'This value determines whether NAT is configured'rw Enumeration .1.3.6.1.4.1.18.3.5.3.2.7.1.1 |
wfNatBaseDisable'The administrative status of NAT in the router. The
value 'enabled' denotes that the NAT Process is active
on at least one interface; 'disabled' disables it on
all interfaces.'rw Enumeration .1.3.6.1.4.1.18.3.5.3.2.7.1.2 |
wfNatBaseState'The state of NAT'ro Enumeration .1.3.6.1.4.1.18.3.5.3.2.7.1.3 |
wfNatBaseSoloistSlotMaskSlot mask for which slots the soloist gate is
eligible to run on. The MSBit represents slot
1, the next most significant bit represents slot 2,
and so on... Slots can be 1-14.
Default is all slots.rw Gauge .1.3.6.1.4.1.18.3.5.3.2.7.1.4 |
wfNatBaseSoloistSlotSlot on which NAT soloist gate is running. Slots
can be 1-14. Default is zero.ro INTEGER .1.3.6.1.4.1.18.3.5.3.2.7.1.5 |
wfNatBaseLogMaskA parameter to specify which NAT log messages should be logged.
Each bit represents a message as defined below. A 1 in that
bit location means to log it and a 0 means not to put that
log message in the log. Changing this value will NOT restart
NAT, but will take effct immediately(if there are any messages
to be logged.
bit 31 bit 0
+
| |
+
NAT_DBG_MIB_LOG 0x00000001
NAT_DBG_IP_LOG 0x00000002
NAT_DBG_FWD_LOG 0x00000004
NAT_DBG_MAPPING_LOG 0x00000008
NAT_DBG_AGING_LOG 0x00000010
NAT_DBG_SYNCH_LOG 0x00000020rw INTEGER .1.3.6.1.4.1.18.3.5.3.2.7.1.6 |
wfNatBaseMapTimeoutThis controls whether or not the dynamic mapping table
entries are aged out when unused.rw Enumeration .1.3.6.1.4.1.18.3.5.3.2.7.1.7 |
wfNatBaseMapMaxTimeoutThe maximum time in seconds before unused NAT mapping
table entries are deleted. This timeout or aging does
not apply to static mapping entries.rw INTEGER .1.3.6.1.4.1.18.3.5.3.2.7.1.8 |
wfNatBaseMapDynMapsCountNumber of Dynamic Mappings in the dymanic mapping tablero Gauge .1.3.6.1.4.1.18.3.5.3.2.7.1.9 |
wfNatBaseFtpSessionCountNumber of FTP sessions detected on this box translated by NATro Gauge .1.3.6.1.4.1.18.3.5.3.2.7.1.10 |
wfNatBaseNto1TrTotCountTotal number of active Nto1 translation counts on the box.ro Gauge .1.3.6.1.4.1.18.3.5.3.2.7.1.11 |
wfNatBaseSynchronizationThe administrative status of NAT Synchronization in the router.
The value `enabled' denotes that the NAT Synchronization is
active and is synchronizing with the peer specified in noraml
conditions.; `disabled' disables it on the box and all the peer
connections will be teared down.'rw Enumeration .1.3.6.1.4.1.18.3.5.3.2.7.1.12 |
wfNatBaseSynRouterIDThis represents the Router Identifier for NAT Synchronization
Only. This is used to detect the duplicate TCP connection
between peers. The value of it can be any integer which is
unique between all the NAT Syn peers this router has.
An IP Address of one of the router interfaces can be used as
the RouterID. Changing the value will result into breaking and
reconnecting using new ID with all the peers.'rw IpAddress .1.3.6.1.4.1.18.3.5.3.2.7.1.13 |
wfNatBaseSynPortThis represents the TCP port on which the connection requests
from the peers will be accepted. When NAT Synchronization
Protocol comes up, it will open a listen connection for this
port number. This attribute value has to be the same on all
the peers that want to make the TCP connection.'rw INTEGER .1.3.6.1.4.1.18.3.5.3.2.7.1.14 |
wfNatBaseSynKeepAlvIntervalIdle session timeout period, in seconds. If an established
TCP connection remains inactive for this interval, KEEPALIVE
messages will be sent to the peer (if the Keepalive Timer is
non-zero). Setting the Idle Timer to zero disables the
keepalive feature.rw INTEGER .1.3.6.1.4.1.18.3.5.3.2.7.1.15 |
wfNatBaseSynKeepAlvTimerKEEPALIVE retransmit timeout period, in seconds. This is
the interval at which unacknowledged KEEPALIVE messages will
be retransmitted. If the Idle Timer is set to zero, this
timer ignored. If the Idle Timer is non-zero and this timer
IS zero, no KEEPALIVEs are sent and the session is terminated
upon expiration of the Idle Timer.rw INTEGER .1.3.6.1.4.1.18.3.5.3.2.7.1.16 |
wfNatBaseSynKeepAlvRetriesNumber of unacknowledged KEEPALIVE messages retransmitted
before the TCP session is terminated. If this count is set
to zero, only one KEEPALIVE message will be sent.rw INTEGER .1.3.6.1.4.1.18.3.5.3.2.7.1.17 |
wfNatBaseLocalToLocalEnableAllow forwarding of traffic from one local
NAT interface to another local NAT interface.rw Enumeration .1.3.6.1.4.1.18.3.5.3.2.7.1.18 |
wfNatBaseInstallUniPrivAddrThis MIB was added in BayRS 14.20 to address a
compatibility issue concerning non-DNS NAT
translations when upgrading from a pre-14.20
NAT configuration to a 14.20 or greater version
of BayRS software. This MIB should remain enabled.
Disabling this MIB will cause Uni-directional NAT
to no longer function correctly on the router.rw Enumeration .1.3.6.1.4.1.18.3.5.3.2.7.1.19 |
wfNatAddrRangeTableTable of address ranges that have been designated
as the set of external apparent addresses that are
to be mapped in place of internal actual addresses.
These addresses would be the non-public reigistered
addresses. SEQUENCE OF WfNatAddrRangeEntry .1.3.6.1.4.1.18.3.5.3.2.7.2 |
wfNatAddrRangeEntry'Information describing each of the available address
ranges.' WfNatAddrRangeEntry .1.3.6.1.4.1.18.3.5.3.2.7.2.1 |
wfNatAddrRangeDelete'Create/Delete parameter. Default is created.
Users perform a set operation on this
object in order to create/delete an address
range entry.'rw Enumeration .1.3.6.1.4.1.18.3.5.3.2.7.2.1.1 |
wfNatAddrRangeDisable'Enable/Disable parameter. Default is enabled.
Users perform a set operation on this
object in order to enable/disable an address
range entry.'rw Enumeration .1.3.6.1.4.1.18.3.5.3.2.7.2.1.2 |
wfNatAddrRangeAddress'The IP beginning address of this range entry.rw IpAddress .1.3.6.1.4.1.18.3.5.3.2.7.2.1.3 |
wfNatAddrRangePrefixLen'The IP address mask that in conjunction with the
start address defines the address range of the entry.'rw INTEGER .1.3.6.1.4.1.18.3.5.3.2.7.2.1.4 |
wfNatLocalAddrRangeTableTable of address ranges that have been designated
as the set of local addresses that are to be mapped
via NAT. SEQUENCE OF WfNatLocalAddrRangeEntry .1.3.6.1.4.1.18.3.5.3.2.7.3 |
wfNatLocalAddrRangeEntry'Information describing each of the available address
ranges.' WfNatLocalAddrRangeEntry .1.3.6.1.4.1.18.3.5.3.2.7.3.1 |
wfNatLocalAddrRangeDelete'Create/Delete parameter. Default is created.
Users perform a set operation on this
object in order to create/delete an address
range entry.'rw Enumeration .1.3.6.1.4.1.18.3.5.3.2.7.3.1.1 |
wfNatLocalAddrRangeDisable'Enable/Disable parameter. Default is enabled.
Users perform a set operation on this
object in order to enable/disable an address
range entry.'rw Enumeration .1.3.6.1.4.1.18.3.5.3.2.7.3.1.2 |
wfNatLocalAddrRangeAddress'The IP beginning address of this range entry.rw IpAddress .1.3.6.1.4.1.18.3.5.3.2.7.3.1.3 |
wfNatLocalAddrRangePrefixLen'The IP address mask that in conjunction with the
start address defines the address range of the entry.'rw INTEGER .1.3.6.1.4.1.18.3.5.3.2.7.3.1.4 |
wfNatLocalAddrRangeNto1AddrNto1 translation address used for this range.rw IpAddress .1.3.6.1.4.1.18.3.5.3.2.7.3.1.5 |
wfNatStaticMapTable'This table creates instances of pre-defined
NAT mappings.' SEQUENCE OF WfNatStaticMapEntry .1.3.6.1.4.1.18.3.5.3.2.7.4 |
wfNatStaticMapEntry'A single local-to-global address mapping.' WfNatStaticMapEntry .1.3.6.1.4.1.18.3.5.3.2.7.4.1 |
wfNatStaticMapDelete'Create/Delete parameter. Default is created.
Users perform a set operation on this
object in order to create/delete a static
address mapping entry.'rw Enumeration .1.3.6.1.4.1.18.3.5.3.2.7.4.1.1 |
wfNatStaticMapDisable'Enable/Disable parameter. Default is enabled.
Users perform a set operation on this
object in order to enable/disable a static
address mapping entry.'rw Enumeration .1.3.6.1.4.1.18.3.5.3.2.7.4.1.2 |
wfNatStaticMapLocalAddress'The local or private address of the mapping pair.'rw IpAddress .1.3.6.1.4.1.18.3.5.3.2.7.4.1.3 |
wfNatStaticMapGlobalAddress'The global or external address of the mapping pair.'rw IpAddress .1.3.6.1.4.1.18.3.5.3.2.7.4.1.4 |
wfNatStaticMapProtocol'The IP protocol of the mapping pair.'rw INTEGER .1.3.6.1.4.1.18.3.5.3.2.7.4.1.5 |
wfNatStaticMapLocalPort'The local UDP or TCP port of the mapping pair.
This will only be relevent if the protocol is
either UDP or TCP.'rw INTEGER .1.3.6.1.4.1.18.3.5.3.2.7.4.1.6 |
wfNatStaticMapGlobalPort'The global UDP or TCP port of the mapping pair.
This will only be relevent if the protocol is
either UDP or TCP.'rw INTEGER .1.3.6.1.4.1.18.3.5.3.2.7.4.1.7 |
wfNatMapTable'This table defines the current set of address
mappings that are in effect.' SEQUENCE OF WfNatMapEntry .1.3.6.1.4.1.18.3.5.3.2.7.5 |
wfNatMapEntry WfNatMapEntry .1.3.6.1.4.1.18.3.5.3.2.7.5.1 |
wfNatMapLocalAddress'The local address of the mapping pair.'ro IpAddress .1.3.6.1.4.1.18.3.5.3.2.7.5.1.1 |
wfNatMapGlobalAddress'The global address of the mapping pair.'ro IpAddress .1.3.6.1.4.1.18.3.5.3.2.7.5.1.2 |
wfNatMapProtocol'The IP protocol of the mapping pair.'ro INTEGER .1.3.6.1.4.1.18.3.5.3.2.7.5.1.3 |
wfNatMapLocalPort'When the mapping is for a TCP connection, this
denotes the TCP port number on the local side.'ro INTEGER .1.3.6.1.4.1.18.3.5.3.2.7.5.1.4 |
wfNatMapGlobalPort'When the mapping is for a TCP connection, this
denotes the TCP port number on the global side.'ro INTEGER .1.3.6.1.4.1.18.3.5.3.2.7.5.1.5 |
wfNatMapTxCount'Number of packets for this mapping pair that have
been mapped from the local to the global network.'ro Counter .1.3.6.1.4.1.18.3.5.3.2.7.5.1.6 |
wfNatMapRxCount'Number of packets for this mapping pair that have
been mapped from the global to the local network.'ro Counter .1.3.6.1.4.1.18.3.5.3.2.7.5.1.7 |
wfNatMapTimeout'The time in seconds since this mapping entry was
last used. This is used to age out mapping entries.'ro Counter .1.3.6.1.4.1.18.3.5.3.2.7.5.1.8 |
wfNatMapModeThis is the bit mask representing the type of this
mapping. Each bit specifies the type as follows:
The mapping could be only ONE of the foolowing three...
0x01000000 - This mapping is origianted on this router,
i.e. this NAT router performed the translation
0x02000000 - This mapping is learned from the peer, i.e.
this translation was learned from the peer using
NAT Synchronization feature.
0x04000000 - This mapping is owned, i.e. it was originally
learned from peer, but this router received traffic
which used this mapping.
...and only ONE of the following three.
0x00000010 - This mapping is the STATIC mapping.
0x00000020 - This mapping is Dynamic(1 to 1) mapping.
0x00000040 - This mapping is N to 1 mapping.ro INTEGER .1.3.6.1.4.1.18.3.5.3.2.7.5.1.9 |
wfNatIfTable'The set of interface that are participating
in the NAT protocol.' SEQUENCE OF WfNatIfEntry .1.3.6.1.4.1.18.3.5.3.2.7.6 |
wfNatIfEntry'An single instance of a NAT interface entry.' WfNatIfEntry .1.3.6.1.4.1.18.3.5.3.2.7.6.1 |
wfNatIfDeleteThis variable determines in a NAT Interface has been
configured on the router.rw Enumeration .1.3.6.1.4.1.18.3.5.3.2.7.6.1.1 |
wfNatIfDisable'The NAT interface's administrative status. The value
'enabled' denotes that NAT has been configured
on the interface. The value 'disabled' denotes that
the interface is not running NAT.'rw Enumeration .1.3.6.1.4.1.18.3.5.3.2.7.6.1.2 |
wfNatIfIpAddressThe IP address of this NAT interface.ro IpAddress .1.3.6.1.4.1.18.3.5.3.2.7.6.1.3 |
wfNatIfCircuitThe circuit number of this interface.rw INTEGER .1.3.6.1.4.1.18.3.5.3.2.7.6.1.4 |
wfNatIfTypeDenotes the type of NAT interface being defined.rw Enumeration .1.3.6.1.4.1.18.3.5.3.2.7.6.1.5 |
wfNatIfState'The state of NAT on this interface'ro Enumeration .1.3.6.1.4.1.18.3.5.3.2.7.6.1.6 |
wfNatIfTxCountNumber of packets mapped over this interface from
the local to the global network.'ro Counter .1.3.6.1.4.1.18.3.5.3.2.7.6.1.7 |
wfNatIfRxCountNumber of packets mapped over this interface from
the global to the local network.'ro Counter .1.3.6.1.4.1.18.3.5.3.2.7.6.1.8 |
wfNatIfPktDropCountNumber of packets dropped on this interfacero Counter .1.3.6.1.4.1.18.3.5.3.2.7.6.1.9 |
wfNatIfDomainWhen wfNatIfType is set to biDirectional, specifies
the Address Domain Name that this interface is
connected to, otherwise set to null.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.18.3.5.3.2.7.6.1.10 |
wfNatSynPeerTableThe Nat Synchronization Peer table contains configuration
and statistical information regarding this router's NAT peers SEQUENCE OF WfNatSynPeerEntry .1.3.6.1.4.1.18.3.5.3.2.7.7 |
wfNatSynPeerEntryAn entry in the NAT Synchronization-Peer table WfNatSynPeerEntry .1.3.6.1.4.1.18.3.5.3.2.7.7.1 |
wfNatSynPeerDeleteCreate/Delete: if set to delete,
this instance of the peer entry is deleted,
which results into the termination of peer connection.rw Enumeration .1.3.6.1.4.1.18.3.5.3.2.7.7.1.1 |
wfNatSynPeerDisableEnable/Disable: controls whether the peer connection
is enabled or disabled, disabling this results into
the termination of TCP connectionrw Enumeration .1.3.6.1.4.1.18.3.5.3.2.7.7.1.2 |
wfNatSynPeerStatethe administrative state of the peer connectionro Enumeration .1.3.6.1.4.1.18.3.5.3.2.7.7.1.3 |
wfNatSynPeerConnTypethe type of the TCP connection with the peer,
whether this connection is accepted from the peer or it was
actively initialted by this router to the peer.ro Enumeration .1.3.6.1.4.1.18.3.5.3.2.7.7.1.4 |
wfNatSynPeerRouterIDA unique non-zero RouterID of the peer that
this router is expecting from the connection
This is also the instance of the Peer Entry.ro IpAddress .1.3.6.1.4.1.18.3.5.3.2.7.7.1.5 |
wfNatSynPeerAddressthe IP Address of the peer,
where the router will send a connect requestrw IpAddress .1.3.6.1.4.1.18.3.5.3.2.7.7.1.6 |
wfNatSynPeerTransSentThe number of translations sent to this peer by the routerro INTEGER .1.3.6.1.4.1.18.3.5.3.2.7.7.1.7 |
wfNatSynPeerTransRecdThe number of translations received from this peer by the routerro INTEGER .1.3.6.1.4.1.18.3.5.3.2.7.7.1.8 |
wfNatAddressRangeTableTable of address ranges. This table was replaced by
wfNatSrcAddressFilterTable and wfNatTranslationPoolTable SEQUENCE OF WfNatAddressRangeEntry .1.3.6.1.4.1.18.3.5.3.2.7.8 |
wfNatAddressRangeEntryInformation describing each of the available address ranges. WfNatAddressRangeEntry .1.3.6.1.4.1.18.3.5.3.2.7.8.1 |
wfNatAddressRangeDeleteCreate/Delete parameter. Default is created. Users perform
a set operation on this object in order to create/delete
an address range entry.rw Enumeration .1.3.6.1.4.1.18.3.5.3.2.7.8.1.1 |
wfNatAddressRangeDisableEnable/Disable parameter. Default is enabled. Users perform
a set operation on this object in order to enable/disable
an address range entry.rw Enumeration .1.3.6.1.4.1.18.3.5.3.2.7.8.1.2 |
wfNatAddressRangeAddressThe IP beginning address of this range entry.ro IpAddress .1.3.6.1.4.1.18.3.5.3.2.7.8.1.3 |
wfNatAddressRangePrefixLenThe number of contiguous bits set in the IP address mask
which are used to define the address range of the entry.ro INTEGER (1 .. 32) .1.3.6.1.4.1.18.3.5.3.2.7.8.1.4 |
wfNatAddressRangeIndexA unique value for this entry in wfNatAddressRangeTable.ro INTEGER .1.3.6.1.4.1.18.3.5.3.2.7.8.1.5 |
wfNatAddressRangeNto1AddrWhen wfNatAddressRangeType is set to srcAddrFilter,
specifies the N-to-1 translation address used for
this range, otherwise set to zero.rw IpAddress .1.3.6.1.4.1.18.3.5.3.2.7.8.1.6 |
wfNatAddressRangeTypeDenotes the type of address range being defined.
sourceAddrFilter: a range of IP addresses used to detect packets
which need traditional NAT forwarding.
translationPool: for traditional NAT forwarding, a range of
IP addresses from which translation addresses are picked.
domainSrcAddrFilter: a range of IP addresses used to detect domain
specific packets which need domain specific NAT forwarding.
domainTransPool: for domain specific NAT forwarding, a range of
IP addresses from which domain specific translation addresses
are picked.rw Enumeration .1.3.6.1.4.1.18.3.5.3.2.7.8.1.7 |
wfNatAddressRangeDomainWhen wfNatAddressRangeType is set to domainSrcAddrFilter or
domainTransPool, specifies the Address Domain Name that this
address range is valid for, otherwise set to null.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.18.3.5.3.2.7.8.1.8 |
wfNatAddressRangeTransPoolThis attribute is only valid for the wfNatAddressRangeType as
domainSrcAddrFilter(3). The value of this attribute decides
where to get the translation address for this range from.
This could be either the translation Pool defined for the
inbound domain or the outbound domain for the packet in
question.rw Enumeration .1.3.6.1.4.1.18.3.5.3.2.7.8.1.9 |
wfNatAddressRangeStaticNextHopThe IP address of the next hop of this range entry.rw IpAddress .1.3.6.1.4.1.18.3.5.3.2.7.8.1.10 |
wfNatAddressRangeUnnumCctThis Nat Address range over the unnumbered interface.rw INTEGER .1.3.6.1.4.1.18.3.5.3.2.7.8.1.11 |
wfNatStaticMappingTable`This table creates instances of pre-defined NAT translations.' SEQUENCE OF WfNatStaticMappingEntry .1.3.6.1.4.1.18.3.5.3.2.7.9 |
wfNatStaticMappingEntryA single original source address to translated address
translation. WfNatStaticMappingEntry .1.3.6.1.4.1.18.3.5.3.2.7.9.1 |
wfNatStaticMappingDeleteCreate/Delete parameter. Default is created. Users perform a set
operation on this object in order to create/delete a static
address translation entry.rw Enumeration .1.3.6.1.4.1.18.3.5.3.2.7.9.1.1 |
wfNatStaticMappingDisableEnable/Disable parameter. Default is enabled. Users perform a
set operation on this object in order to enable/disable a static
address translation entry.rw Enumeration .1.3.6.1.4.1.18.3.5.3.2.7.9.1.2 |
wfNatStaticMappingOrigAddressThe original (un-translated) address of the translation.rw IpAddress .1.3.6.1.4.1.18.3.5.3.2.7.9.1.3 |
wfNatStaticMappingTransAddressThe translated address of the translation.ro IpAddress .1.3.6.1.4.1.18.3.5.3.2.7.9.1.4 |
wfNatStaticMappingProtocolThe IP protocol of the translation. Example values are
6 for TCP, and 17 for UDP.ro INTEGER .1.3.6.1.4.1.18.3.5.3.2.7.9.1.5 |
wfNatStaticMappingOrigPortThe original (domain specific) UDP or TCP port of the
translation. This will only be relevent if the protocol
is either UDP or TCP.rw INTEGER .1.3.6.1.4.1.18.3.5.3.2.7.9.1.6 |
wfNatStaticMappingTransPortThe translated UDP or TCP port of the translation. This will
only be relevent if the protocol is either UDP or TCP.ro INTEGER .1.3.6.1.4.1.18.3.5.3.2.7.9.1.7 |
wfNatStaticMappingInDomainThis attribute specifies the name of the address domain that this
source translation shall be valid for. In other words, this
translation shall only be valid for source addresses coming
inbound from this domain.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.18.3.5.3.2.7.9.1.8 |
wfNatStaticMappingOutDomainThis attribute specifies the name of the outbound address
domain that this translation will be valid for. In other words,
this translation only applies to translations that will be
forwarded out into this address domain.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.18.3.5.3.2.7.9.1.9 |
wfNatStaticMappingStaticNextHopThe IP address of the next hop of this static entry.rw IpAddress .1.3.6.1.4.1.18.3.5.3.2.7.9.1.10 |
wfNatStaticMappingUnnumCctThis Nat static translation over the unnumbered interface.rw INTEGER .1.3.6.1.4.1.18.3.5.3.2.7.9.1.11 |
wfNatMappingTableThis table defines the current set of address translations
that are in effect. SEQUENCE OF WfNatMappingEntry .1.3.6.1.4.1.18.3.5.3.2.7.10 |
wfNatMappingEntryA single original source address to translated address
translation. WfNatMappingEntry .1.3.6.1.4.1.18.3.5.3.2.7.10.1 |
wfNatMappingOrigAddressThe original (un-translated) address of the translation.ro IpAddress .1.3.6.1.4.1.18.3.5.3.2.7.10.1.1 |
wfNatMappingTransAddressThe translated address of the translation.ro IpAddress .1.3.6.1.4.1.18.3.5.3.2.7.10.1.2 |
wfNatMappingProtocol`The IP protocol of the translation.'ro INTEGER .1.3.6.1.4.1.18.3.5.3.2.7.10.1.3 |
wfNatMappingOrigPortWhen the translation is for a TCP connection, this denotes
the original TCP port number.ro INTEGER .1.3.6.1.4.1.18.3.5.3.2.7.10.1.4 |
wfNatMappingTransPortWhen the translation is for a TCP connection, this denotes
the translated TCP port number.ro INTEGER .1.3.6.1.4.1.18.3.5.3.2.7.10.1.5 |
wfNatMappingTxCountNumber of packets forwarded by NAT using this translation.ro Counter .1.3.6.1.4.1.18.3.5.3.2.7.10.1.6 |
wfNatMappingRxCountNumber of packets received by NAT using this translation.ro Counter .1.3.6.1.4.1.18.3.5.3.2.7.10.1.7 |
wfNatMappingTimeoutThe time in seconds since this translation entry was last used.
This is used to age out translation entries.ro Counter .1.3.6.1.4.1.18.3.5.3.2.7.10.1.8 |
wfNatMappingModeThis is the bit mask representing the type of this translation.
Each bit specifies the type as follows:
The translation could be only ONE of the following three...
0x01000000 - This translation is origianted on this router,
i.e. this NAT router performed the translation.
0x02000000 - This translation is learned from the peer,
i.e. this translation was learned from the
peer using NAT Synchronization feature.
0x04000000 - This translation is owned,
i.e. it was originally learned from peer, but
this router received traffic which used this
translation.
...and only ONE of the following three.
0x00000010 - This translation is the STATIC translation.
0x00000020 - This translation is Dynamic(1 to 1) translation.
0x00000040 - This translation is N to 1 translation.ro INTEGER .1.3.6.1.4.1.18.3.5.3.2.7.10.1.9 |
wfNatMappingInDomainThis attribute specifies the name of the address domain that this
source translation shall be valid for. In ther words, this
translation shall only be valid for source addresses coming
inbound from this domain.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.18.3.5.3.2.7.10.1.10 |
wfNatMappingOutDomainThis attribute specifies the name of the outbound address domain
that this translation will be valid for. In other words, this
translation only applies to translations that will be forwarded
out into this address domain.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.18.3.5.3.2.7.10.1.11 |
wfNatIntfTable'The list of configured NAT interfaces.' SEQUENCE OF WfNatIntfEntry .1.3.6.1.4.1.18.3.5.3.2.7.11 |
wfNatIntfEntry'A NAT interface description.' WfNatIntfEntry .1.3.6.1.4.1.18.3.5.3.2.7.11.1 |
wfNatIntfDeleteThis variable determines if a NAT Interface has been
configured on the router.rw Enumeration .1.3.6.1.4.1.18.3.5.3.2.7.11.1.1 |
wfNatIntfDisable'The NAT interface's administrative status. The value
'enabled' denotes that NAT has been configured
on the interface. The value 'disabled' denotes that
the interface is not running NAT.'rw Enumeration .1.3.6.1.4.1.18.3.5.3.2.7.11.1.2 |
wfNatIntfIpAddressThe IP address of this NAT interface.ro IpAddress .1.3.6.1.4.1.18.3.5.3.2.7.11.1.3 |
wfNatIntfCircuitThe circuit number of this interface.rw INTEGER .1.3.6.1.4.1.18.3.5.3.2.7.11.1.4 |
wfNatIntfDomainThis attribute specifies the Address Domain
Name that this interface is connected to.
Unidirectional NAT interfaces should be set
with domain name of 'private' or 'public'rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.18.3.5.3.2.7.11.1.5 |
wfNatIntfState'The state of NAT on this interface'ro Enumeration .1.3.6.1.4.1.18.3.5.3.2.7.11.1.6 |
wfNatIntfTxCountNumber of packets mapped over this interface from
the local to the global network.'ro Counter .1.3.6.1.4.1.18.3.5.3.2.7.11.1.7 |
wfNatIntfRxCountNumber of packets mapped over this interface from
the global to the local network.'ro Counter .1.3.6.1.4.1.18.3.5.3.2.7.11.1.8 |
wfNatIntfPktDropCountNumber of packets dropped on this interfacero Counter .1.3.6.1.4.1.18.3.5.3.2.7.11.1.9 |
wfNatSrcAddressFilterTableTable of NAT source address filters. SEQUENCE OF WfNatSrcAddressFilterEntry .1.3.6.1.4.1.18.3.5.3.2.7.12 |
wfNatSrcAddressFilterEntryInformation describing each of the available source
address filters. WfNatSrcAddressFilterEntry .1.3.6.1.4.1.18.3.5.3.2.7.12.1 |
wfNatSrcAddressFilterDeleteCreate/Delete parameter. Default is created. Users perform
a set operation on this object in order to create/delete
a source address filter entry.rw Enumeration .1.3.6.1.4.1.18.3.5.3.2.7.12.1.1 |
wfNatSrcAddressFilterDisableEnable/Disable parameter. Default is enabled. Users perform
a set operation on this object in order to enable/disable
a source address filter entry.rw Enumeration .1.3.6.1.4.1.18.3.5.3.2.7.12.1.2 |
wfNatSrcAddressFilterAddressThe IP beginning address of this source address filter entry.ro IpAddress .1.3.6.1.4.1.18.3.5.3.2.7.12.1.3 |
wfNatSrcAddressFilterPrefixLenThe number of contiguous bits set in the IP address mask
which are used to define the address range of the entry.ro INTEGER (1 .. 32) .1.3.6.1.4.1.18.3.5.3.2.7.12.1.4 |
wfNatSrcAddressFilterIndexA unique value for this entry in wfNatSrcAddressFilterTable.ro INTEGER .1.3.6.1.4.1.18.3.5.3.2.7.12.1.5 |
wfNatSrcAddressFilterNto1Addrspecifies the N-to-1 translation address used for
this source address filter, otherwise set to zero.rw IpAddress .1.3.6.1.4.1.18.3.5.3.2.7.12.1.6 |
wfNatSrcAddressFilterDomainThe value of this attribute specifies the Address
Domain Name that this source address filter is valid for.
For Unidirectional NAT this value must be 'public'rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.18.3.5.3.2.7.12.1.7 |
wfNatSrcAddressFilterTransPoolSelectorThe value of this attribute selects where to
get the translation address for this source address
filter from. This could be either the translation
Pool defined for the inbound domain or the outbound
domain for the packet in question.rw Enumeration .1.3.6.1.4.1.18.3.5.3.2.7.12.1.8 |
wfNatSrcAddressFilterStaticNextHopThe IP address of the next hop of this source address
filter entry.rw IpAddress .1.3.6.1.4.1.18.3.5.3.2.7.12.1.9 |
wfNatSrcAddressFilterUnnumCctThis Nat source address filter over the unnumbered interface.rw INTEGER .1.3.6.1.4.1.18.3.5.3.2.7.12.1.10 |
wfNatTranslationPoolTableTable of address ranges. SEQUENCE OF WfNatTranslationPoolEntry .1.3.6.1.4.1.18.3.5.3.2.7.13 |
wfNatTranslationPoolEntryInformation describing each of the available
translation pool. WfNatTranslationPoolEntry .1.3.6.1.4.1.18.3.5.3.2.7.13.1 |
wfNatTranslationPoolDeleteCreate/Delete parameter. Default is created. Users perform
a set operation on this object in order to create/delete
a translation pool entry.rw Enumeration .1.3.6.1.4.1.18.3.5.3.2.7.13.1.1 |
wfNatTranslationPoolDisableEnable/Disable parameter. Default is enabled. Users perform
a set operation on this object in order to enable/disable
a translation pool entry.rw Enumeration .1.3.6.1.4.1.18.3.5.3.2.7.13.1.2 |
wfNatTranslationPoolAddressThe IP beginning address of this translation pool entry.ro IpAddress .1.3.6.1.4.1.18.3.5.3.2.7.13.1.3 |
wfNatTranslationPoolPrefixLenThe number of contiguous bits set in the IP address mask
which are used to define the address range of the entry.ro INTEGER (1 .. 32) .1.3.6.1.4.1.18.3.5.3.2.7.13.1.4 |
wfNatTranslationPoolIndexA unique value for this entry in wfNatTranslationPoolTable.ro INTEGER .1.3.6.1.4.1.18.3.5.3.2.7.13.1.5 |
wfNatTranslationPoolDomainThe value of this attribute specifies the Address
Domain Name that this translation pool is valid for.
For Unidirectional NAT this value must be 'public'rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.18.3.5.3.2.7.13.1.6 |