Wellfleet-MCT1-MIB
Detailed view of the defined objects, syntax rules, and hierarchical paths.
160
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
160 total| Object Name |
|---|
RFC1155-SMIMCT1 MOD record - Contains MCT1 module Configuration parameters SEQUENCE OF WfMcT1ModEntry .1.3.6.1.4.1.18.3.4.8.1 |
wfMcT1TableMCT1 line record - Contains MUNICH32 Configuration parameters SEQUENCE OF WfMcT1Entry .1.3.6.1.4.1.18.3.4.8.2 |
wfMcT1EntryAn entry in the MCT1 table WfMcT1Entry .1.3.6.1.4.1.18.3.4.8.2.1 |
wfMcT1DeleteCreate/Delete parameterrw Enumeration .1.3.6.1.4.1.18.3.4.8.2.1.1 |
wfMcT1DisableEnable/Disable parameterrw Enumeration .1.3.6.1.4.1.18.3.4.8.2.1.2 |
wfMcT1StateLine Driver state variablero Enumeration .1.3.6.1.4.1.18.3.4.8.2.1.3 |
wfMcT1SlotInstance ID Slot, filled in by driverro INTEGER .1.3.6.1.4.1.18.3.4.8.2.1.4 |
wfMcT1ConnectorInstance ID Connector, filled in by driverro Enumeration .1.3.6.1.4.1.18.3.4.8.2.1.5 |
wfMcT1OperationModeAn option to generate and analyze specific test patterns
is provided in BERT mode of operation. Only one T1 port
can be in BERT mode at a time. This attribute selects
normal or BERT mode of operationrw Enumeration .1.3.6.1.4.1.18.3.4.8.2.1.6 |
wfMcT1MtuMTU parameter. Specifies the largest frame size that
can be received by the MCT1 link module. Any received frame
which is larger than the MTU will be discarded.rw INTEGER .1.3.6.1.4.1.18.3.4.8.2.1.7 |
wfMcT1MunichVersionSpecifies version number of the MUNICH chip usedro Enumeration .1.3.6.1.4.1.18.3.4.8.2.1.8 |
wfMcT1Dsx1LineTypeSelects between the two framing formats supported - D4 and ESF.
The sailent differences between the two formats are the number
of frames per superframe and the use of F-bit position.rw Enumeration .1.3.6.1.4.1.18.3.4.8.2.1.9 |
wfMcT1Dsx1ZeroCodingSelects between the two Zero Code Suppression formats
used on the link. In B8ZS coding, any outgoing stream of
eight consecutive zeroes is replaced with a B8ZS code word.
Any received B8ZS code is replaced with all zeroes.rw Enumeration .1.3.6.1.4.1.18.3.4.8.2.1.10 |
wfMcT1Dsx1LoopbackConfigIndicates the loopback configuration of the T1 interface.
The interface can be in the following loopback states:
Payload loopback and Line loopback or no loopback. The
loopbacks can be initiated by the manager of this device
or by the far end. The loopbacks initiated by the far end
are NETREQPAYLOADLOOP and NETREQLINELOOP.ro Enumeration .1.3.6.1.4.1.18.3.4.8.2.1.11 |
wfMcT1Dsx1LineStatusIndicates the line status of the T1 interface. It
contains loopback state and alarm state information.
The Dsx1LineStatus is a bit map therefore it can represent
multiple loopback and alarm states simultaneously.ro Enumeration .1.3.6.1.4.1.18.3.4.8.2.1.12 |
wfMcT1Dsx1SetupAlarmThresholdSpecifies setup time for performance failure conditions,
in seconds. When a performance defect is present for greater
than the time specified by this parameter a performance
failure is registered and a message is logged.rw Enumeration .1.3.6.1.4.1.18.3.4.8.2.1.13 |
wfMcT1Dsx1ClearAlarmThresholdSpecifies clear time for performance failure conditions,
in seconds. When a performance failure condition has been
cleared for greater than the time specified by this parameter
then the failure cleared condition is registered and a
message is logged.rw Enumeration .1.3.6.1.4.1.18.3.4.8.2.1.14 |
wfMcT1Dsx1SignalLevelSpecifies T1 transmit power level, in terms of DB. They
translate into cable length as follows:
0.0dB -> 0-133 ft
0.5dB -> 133-266 ft
0.8dB -> 266-399 ft
1.1dB -> 399-533 ft
1.5dB -> 533-655 ftrw Enumeration .1.3.6.1.4.1.18.3.4.8.2.1.15 |
wfMcT1LoopbackDisableThe MCT1 link module is capable of detecting loop up
and loop down codes received from the far end. This
parameter enables or disbales loop up/down code detection
circuitryrw Enumeration .1.3.6.1.4.1.18.3.4.8.2.1.16 |
wfMcT1Dsx1FDLOperationModeSelect between the two FDL modes of operation. The AT&T
mode, 54016 is based on AT&T publication 54015-1989. The
ANSI mode, T1403 is based on ANSI publication T1.403-1989rw Enumeration .1.3.6.1.4.1.18.3.4.8.2.1.17 |
wfMcT1BertTxOutputLevelSpecifies T1 transmit power level, in terms of DB while
the T1 port is in BERT mode. The power levels translate into
cable length as follows:
0.0dB -> 0-133 ft
0.5dB -> 133-266 ft
0.8dB -> 266-399 ft
1.1dB -> 399-533 ft
1.5dB -> 533-655 ftrw Enumeration .1.3.6.1.4.1.18.3.4.8.2.1.18 |
wfMcT1BertTestModeSelects between the framing formats while in bert mode of
operation.rw Enumeration .1.3.6.1.4.1.18.3.4.8.2.1.19 |
wfMcT1BertLineCodeSelects between the two Zero Code Suppression formats
used on the link while in BERT mode. In B8ZS coding,
any outgoing stream of eight consecutive zeroes is replaced
with a B8ZS code word. Any received B8ZS code is replaced
with all zeroes.rw Enumeration .1.3.6.1.4.1.18.3.4.8.2.1.20 |
wfMcT1BertTestPatternWhen a T1 port is in BERT mode, it is capable of generating
a set of known patterns. This paramater selects between those
patternsrw Enumeration .1.3.6.1.4.1.18.3.4.8.2.1.21 |
wfMcT1BertSendAlarmSpecifies a blue or yellow alarm to be transmitted
while in BERT mode.rw Enumeration .1.3.6.1.4.1.18.3.4.8.2.1.22 |
wfMcT1DS2282VersionSpecifies version number of DS2282 chipro INTEGER .1.3.6.1.4.1.18.3.4.8.2.1.23 |
wfMcT1RestartIndicates Port gate should be restarted to read
new configurationrw INTEGER .1.3.6.1.4.1.18.3.4.8.2.1.24 |
wfMcT1LoopbackSelects line or payload loopback to be activated locallyrw Enumeration .1.3.6.1.4.1.18.3.4.8.2.1.25 |
wfMcT1FDLTargetAddressSelects between the two FDL target address modesrw Enumeration .1.3.6.1.4.1.18.3.4.8.2.1.26 |
wfMcT1ConfigTableMCT1 configuration record - Contains MUNICH32 and Framer
write only Configuration parameters SEQUENCE OF WfMcT1ConfigEntry .1.3.6.1.4.1.18.3.4.8.3 |
wfMcT1ConfigEntryAn entry in the MCT1 Config table WfMcT1ConfigEntry .1.3.6.1.4.1.18.3.4.8.3.1 |
wfMcT1ConfigSlotInstance ID Slot, filled in by driverro INTEGER .1.3.6.1.4.1.18.3.4.8.3.1.1 |
wfMcT1ConfigConnectorInstance ID Connector, filled in by driverro Enumeration .1.3.6.1.4.1.18.3.4.8.3.1.2 |
wfMcT1BertRestartReset counters on BERT devicerw Enumeration .1.3.6.1.4.1.18.3.4.8.3.1.3 |
wfMcT1BertPayldLbSelects a payload loopback code to be sent to the far end
by the FDL while in BERT mode. It can be a payload loopback
activate or deactivate code.rw Enumeration .1.3.6.1.4.1.18.3.4.8.3.1.4 |
wfMcT1BertLineLbSelects a line loopback code to be sent to the far end while in
BERT mode. It can be a line loopback activate or deactivate
code using the hardware on the MCT1 board or it can be a code
sent by the FDL.rw Enumeration .1.3.6.1.4.1.18.3.4.8.3.1.5 |
wfMcT1BertErrorInsertIndicates that an error be injected into the transmitted data
stream while in BERT mode.rw Enumeration .1.3.6.1.4.1.18.3.4.8.3.1.6 |
wfMcT1Dsx1SendLoopCodeSelects a Loop Up/Down code to be sent to the remote endrw Enumeration .1.3.6.1.4.1.18.3.4.8.3.1.7 |
wfMcT1Dsx1SendFDLCodeSelects an FDL code to be sent to the remote endrw Enumeration .1.3.6.1.4.1.18.3.4.8.3.1.8 |
wfMcT1LineTableMCT1 Channel record - Contains configuration parameters and
statistics for MUNICH32 which are channel specific. SEQUENCE OF WfMcT1LineEntry .1.3.6.1.4.1.18.3.4.8.4 |
wfMcT1LineEntryAn entry in the MCT1CHANNEL table WfMcT1LineEntry .1.3.6.1.4.1.18.3.4.8.4.1 |
wfMcT1LineDeleteCreate/Delete parameterrw Enumeration .1.3.6.1.4.1.18.3.4.8.4.1.1 |
wfMcT1LineDisableEnable/Disable parameterrw Enumeration .1.3.6.1.4.1.18.3.4.8.4.1.2 |
wfMcT1LineStateLine Driver state variablero Enumeration .1.3.6.1.4.1.18.3.4.8.4.1.3 |
wfMcT1LineSlotInstance ID Slot, filled in by driverro INTEGER .1.3.6.1.4.1.18.3.4.8.4.1.4 |
wfMcT1LineConnectorInstance ID Connector, filled in by driverro Enumeration .1.3.6.1.4.1.18.3.4.8.4.1.5 |
wfMcT1LineLineLine number for this line instance, filled in by driver.
The line number corresponds to the position of the
circuit, from 1 to 24, on the port.ro INTEGER .1.3.6.1.4.1.18.3.4.8.4.1.6 |
wfMcT1LineCctCircuit number for this line instancerw INTEGER .1.3.6.1.4.1.18.3.4.8.4.1.7 |
wfMcT1LineBoflSelects Breath of Life (BOFL) parameter. If selected, a BOFL
packet is sent out on the wire as often as specifies by the
wfMcT1LineBoflTmo parameterrw Enumeration .1.3.6.1.4.1.18.3.4.8.4.1.8 |
wfMcT1LineBoflTmoIndicates the time-period between BOFL packetsrw INTEGER .1.3.6.1.4.1.18.3.4.8.4.1.9 |
wfMcT1LineFractionalLpbkAny circuit on this T1 port is capable of being put into
loopback, i.e. data coming into that circuit from the wire is
mirrorred back onto the wire. This parameter enables or
disables this loopback feature on any circuit.rw Enumeration .1.3.6.1.4.1.18.3.4.8.4.1.10 |
wfMcT1LineChannelAssignmentLists the time-slots which constitute this channel. User
types in a list of time-slots from 1 to 24 separated by commasrw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.18.3.4.8.4.1.11 |
wfMcT1LineMadrLine MAC address, fixed - line driver fills in from the 48 bit
address stored in the serial number prom.ro OCTET STRING .1.3.6.1.4.1.18.3.4.8.4.1.12 |
wfMcT1LineWanProtocolWAN protocol selection is provided via this parameter. The
supported protocols can be selected per circuit.rw Enumeration .1.3.6.1.4.1.18.3.4.8.4.1.13 |
wfMcT1LineServiceService type for this circuit. Supports raw HDLC mode.
Does not support LLC1 at this time. LLC1 mode
will prefix the HDLC address and control fields to the
frame. May support LLC1 mode in the futurerw Enumeration .1.3.6.1.4.1.18.3.4.8.4.1.14 |
wfMcT1LineRateAdaptionDetermines the number of bits and their bit positions
within the time-slot. 64k selection uses all 8 bits in
the time-slot. The two 56k selections use 7 of the 8
bits in the time-slot. 56k_MSB does not use the most
significant bit and 56k_LSB does not use the least
significant bit in the time-slot.rw Enumeration .1.3.6.1.4.1.18.3.4.8.4.1.15 |
wfMcT1LineIFTFDetermines the Interframe time fill character to be
transmitted by the MUNICH. In case of IFTF_FLAGS, 0x7E
is sent and in case of IFTF_IDLES 0xff is sent as the
interframe timefill characters.rw Enumeration .1.3.6.1.4.1.18.3.4.8.4.1.16 |
wfMcT1LineCRCSizeDetermines the CRC Size. When CRC32 is selected a 32 bit
CRC is appended to the frame being transmitted and a 32
bit CRC check is performed on the received frame. When
CRC16 is selected, a 16 bit CRC is appended to the
transmitted frame and a 16 bit CRC is performed. on the
received frame.rw Enumeration .1.3.6.1.4.1.18.3.4.8.4.1.17 |
wfMcT1LineRxOctetsNumber of octets received without errorro Counter .1.3.6.1.4.1.18.3.4.8.4.1.18 |
wfMcT1LineRxFramesNumber of frames received without errorro Counter .1.3.6.1.4.1.18.3.4.8.4.1.19 |
wfMcT1LineTxOctetsNumber of octets transmitted without errorro Counter .1.3.6.1.4.1.18.3.4.8.4.1.20 |
wfMcT1LineTxFramesNumber of frames transmitted without errorro Counter .1.3.6.1.4.1.18.3.4.8.4.1.21 |
wfMcT1LineRxErrorsNumber of receive errorsro Counter .1.3.6.1.4.1.18.3.4.8.4.1.22 |
wfMcT1LineTxErrorsNumber of transmission errorsro Counter .1.3.6.1.4.1.18.3.4.8.4.1.23 |
wfMcT1LineLackRxResourcesNumber of Rx frames dropped due to lack of buffer resourcesro Counter .1.3.6.1.4.1.18.3.4.8.4.1.24 |
wfMcT1LineLackTxResourcesNumber of Tx frames dropped due to lack of buffer resourcesro Counter .1.3.6.1.4.1.18.3.4.8.4.1.25 |
wfMcT1LineTxUnderflowsNumber of Tx frames dropped due to Transmit underflowro Counter .1.3.6.1.4.1.18.3.4.8.4.1.26 |
wfMcT1LineRxOverflowsNumber of Rx frames dropped due to Receive overflowro Counter .1.3.6.1.4.1.18.3.4.8.4.1.27 |
wfMcT1LineRxNullFramesNumber of short frames received (with no data bytes)ro Counter .1.3.6.1.4.1.18.3.4.8.4.1.28 |
wfMcT1LineRxShortFramesNumber of short frames received (less than or equal to two
data bytes)ro Counter .1.3.6.1.4.1.18.3.4.8.4.1.29 |
wfMcT1LineRxLossSyncsLoss of synchronization on receiverro Counter .1.3.6.1.4.1.18.3.4.8.4.1.30 |
wfMcT1LineRxCRCErrorsCRC error receivedro Counter .1.3.6.1.4.1.18.3.4.8.4.1.31 |
wfMcT1LineRxNonOctetBitsNon-Octet bits received in framero Counter .1.3.6.1.4.1.18.3.4.8.4.1.32 |
wfMcT1LineRxLongFramesFrame longer than MFL receivedro Counter .1.3.6.1.4.1.18.3.4.8.4.1.33 |
wfMcT1LineRxAbortFramesAborted frame receivedro Counter .1.3.6.1.4.1.18.3.4.8.4.1.34 |
wfMcT1LineRxDescOverflowsReceive overflow on chip bufferro Counter .1.3.6.1.4.1.18.3.4.8.4.1.35 |
wfMcT1LineTurboBoflDEBUG parameter - Turbo bofl enabled or disabledrw Enumeration .1.3.6.1.4.1.18.3.4.8.4.1.36 |
wfMcT1LineBoflNumDEBUG parameter - Number of breath of life packets per breath
of liferw INTEGER .1.3.6.1.4.1.18.3.4.8.4.1.37 |
wfMcT1LineBoflLenDEBUG parameter - breath of life packet lengthrw INTEGER .1.3.6.1.4.1.18.3.4.8.4.1.38 |
wfMcT1LineRxIntProcsReceive Interrupt processing countro Counter .1.3.6.1.4.1.18.3.4.8.4.1.39 |
wfMcT1LineTxIntProcsTx interrupt processing countro Counter .1.3.6.1.4.1.18.3.4.8.4.1.40 |
wfMcT1LineRxPktCorruptionsCorruption check on receivero Counter .1.3.6.1.4.1.18.3.4.8.4.1.41 |
wfMcT1LineRxReplenMissesCount of number of packet buffer misses while attempting to
replenish driver receive ringro Counter .1.3.6.1.4.1.18.3.4.8.4.1.42 |
wfMcT1LineRxIFCsNumber of times the device changes its interframe time-fillro Counter .1.3.6.1.4.1.18.3.4.8.4.1.43 |
wfMcT1LineCfgTxQueueLengthConfigured transmit queue lengthrw INTEGER .1.3.6.1.4.1.18.3.4.8.4.1.44 |
wfMcT1LineCfgRxQueueLengthConfigured receive queue lengthrw INTEGER .1.3.6.1.4.1.18.3.4.8.4.1.45 |
wfMcT1LineTxQueueLengthCurrent transmit queue lengthro INTEGER .1.3.6.1.4.1.18.3.4.8.4.1.46 |
wfMcT1LineRxQueueLengthCurrent Receive queue lengthro INTEGER .1.3.6.1.4.1.18.3.4.8.4.1.47 |
wfMcT1LineTxQueueEmptyThe number of times the transmit ring is found
empty when transmitting packetsro INTEGER .1.3.6.1.4.1.18.3.4.8.4.1.48 |
wfMcT1LineMtuMTU read-only parameter. Specifies the largest frame size that
can be received by the MCT1 link module. Any received frame
which is larger than the MTU will be discarded. Can be set in
MCT1Entry TABLE by the userro INTEGER .1.3.6.1.4.1.18.3.4.8.4.1.49 |
wfMcT1LineRestartIndicates channel gate should be restarted to read
new configurationrw INTEGER .1.3.6.1.4.1.18.3.4.8.4.1.50 |
wfMcT1LineLineNumberline number for this line instancerw INTEGER .1.3.6.1.4.1.18.3.4.8.4.1.51 |
wfMcT1Dsx1CurrentTableThe MCT1_DSX1 Current table SEQUENCE OF WfMcT1Dsx1CurrentEntry .1.3.6.1.4.1.18.3.4.8.5 |
wfMcT1Dsx1CurrentEntryper circuit MCT1_DSX1 current objects - wfMcT1Dsx1CurrentIndex
corresponds to Wellfleet circuit number WfMcT1Dsx1CurrentEntry .1.3.6.1.4.1.18.3.4.8.5.1 |
wfMcT1Dsx1CurrentSlotthis corresponds to the Wellfleet Slot numberro INTEGER .1.3.6.1.4.1.18.3.4.8.5.1.1 |
wfMcT1Dsx1CurrentConnectorthis corresponds to the Wellfleet Connector numberro Enumeration .1.3.6.1.4.1.18.3.4.8.5.1.2 |
wfMcT1Dsx1CurrentIntervalTimerthe number of seconds in the current 15 minute intervalro Gauge .1.3.6.1.4.1.18.3.4.8.5.1.3 |
wfMcT1Dsx1CurrentESsthe number of errored seconds encountered by a DS1
interface in the current 15 minute intervalro Gauge .1.3.6.1.4.1.18.3.4.8.5.1.4 |
wfMcT1Dsx1CurrentSESsthe number of severely errored seconds in the
current 15 minute intervalro Gauge .1.3.6.1.4.1.18.3.4.8.5.1.5 |
wfMcT1Dsx1CurrentBESsthe number of bursty errored seconds in the
current 15 minute intervalro Gauge .1.3.6.1.4.1.18.3.4.8.5.1.6 |
wfMcT1Dsx1CurrentUASsthe number of unavailable seconds in the current 15
minute intervalro Gauge .1.3.6.1.4.1.18.3.4.8.5.1.7 |
wfMcT1Dsx1CurrentCSSsthe number of Controlled Slip seconds in the current 15
minute intervalro Gauge .1.3.6.1.4.1.18.3.4.8.5.1.8 |
wfMcT1Dsx1CurrentBPVsthe number of bipolar violations in the current 15
minute intervalro Gauge .1.3.6.1.4.1.18.3.4.8.5.1.9 |
wfMcT1Dsx1IntervalTableThe MCT1_DSX1 Interval table SEQUENCE OF WfMcT1Dsx1IntervalEntry .1.3.6.1.4.1.18.3.4.8.6 |
wfMcT1Dsx1IntervalEntryper circuit MCT1_DSX1 interval objects - wfMcT1Dsx1IntervalIndex
corresponds to Wellfleet circuit number,
wfMcT1Dsx1IntervalNumber is the numbered previous
15-minute interval WfMcT1Dsx1IntervalEntry .1.3.6.1.4.1.18.3.4.8.6.1 |
wfMcT1Dsx1IntervalSlotthis corresponds to the Wellfleet Slot numberro INTEGER .1.3.6.1.4.1.18.3.4.8.6.1.1 |
wfMcT1Dsx1IntervalConnectorthis corresponds to the Wellfleet Connector numberro Enumeration .1.3.6.1.4.1.18.3.4.8.6.1.2 |
wfMcT1Dsx1IntervalNumber1..96 where 1 is the most recent 15-minute interval and 96 is
the leastro INTEGER .1.3.6.1.4.1.18.3.4.8.6.1.3 |
wfMcT1Dsx1IntervalESsthe number of errored seconds in the specified intervalro Gauge .1.3.6.1.4.1.18.3.4.8.6.1.4 |
wfMcT1Dsx1IntervalSESsthe number of severely errored seconds in the specified
intervalro Gauge .1.3.6.1.4.1.18.3.4.8.6.1.5 |
wfMcT1Dsx1IntervalBESsthe number of bursty errored seconds in the
specified intervalro Gauge .1.3.6.1.4.1.18.3.4.8.6.1.6 |
wfMcT1Dsx1IntervalUASsthe number of unavailable seconds in the specified intervalro Gauge .1.3.6.1.4.1.18.3.4.8.6.1.7 |
wfMcT1Dsx1IntervalCSSsthe number of controlled slip seconds in the specified intervalro Gauge .1.3.6.1.4.1.18.3.4.8.6.1.8 |
wfMcT1Dsx1IntervalBPVsthe number of bipolar violations in the specified intervalro Gauge .1.3.6.1.4.1.18.3.4.8.6.1.9 |
wfMcT1Dsx1TotalTableThe MCT1_DSX1 Total table SEQUENCE OF WfMcT1Dsx1TotalEntry .1.3.6.1.4.1.18.3.4.8.7 |
wfMcT1Dsx1TotalEntryper circuit MCT1_DSX1 total objects - wfMcT1Dsx1TotalIndex
corresponds to Wellfleet circuit number WfMcT1Dsx1TotalEntry .1.3.6.1.4.1.18.3.4.8.7.1 |
wfMcT1Dsx1TotalSlotthis corresponds to the Wellfleet Slot numberro INTEGER .1.3.6.1.4.1.18.3.4.8.7.1.1 |
wfMcT1Dsx1TotalConnectorthis corresponds to the Wellfleet Connector numberro Enumeration .1.3.6.1.4.1.18.3.4.8.7.1.2 |
wfMcT1Dsx1TotalVITRIndicates the number of valid 15 minute intervals
in the previous 24 hour periodro Gauge .1.3.6.1.4.1.18.3.4.8.7.1.3 |
wfMcT1Dsx1TotalESsThe number of errored seconds encountered by the DS1
interface in the previous 24 hour intervalro Gauge .1.3.6.1.4.1.18.3.4.8.7.1.4 |
wfMcT1Dsx1TotalSESsThe number of severely errored seconds encountered by a DS1
interface in the previous 24 hour intervalro Gauge .1.3.6.1.4.1.18.3.4.8.7.1.5 |
wfMcT1Dsx1TotalBESsThe number of bursty errored seconds encountered
by a DS1 interface in the previous 24 hour intervalro Gauge .1.3.6.1.4.1.18.3.4.8.7.1.6 |
wfMcT1Dsx1TotalUASsThe number of unavailable seconds encountered by
by a DS1 interface in the previous 24 hour intervalro Gauge .1.3.6.1.4.1.18.3.4.8.7.1.7 |
wfMcT1Dsx1TotalCSSsThe number of controlled slip seconds encountered
by a DS1 interface in the previous 24 hour intervalro Gauge .1.3.6.1.4.1.18.3.4.8.7.1.8 |
wfMcT1Dsx1TotalBPVsThe number of bipolar violations encountered
by a DS1 interface in the previous 24 hour intervalro Gauge .1.3.6.1.4.1.18.3.4.8.7.1.9 |
wfMcT1AnsiTableANSI Statistics line record - This table contains the
performance parameters for the ANSI register set SEQUENCE OF WfMcT1AnsiEntry .1.3.6.1.4.1.18.3.4.8.8 |
wfMcT1AnsiEntryAn entry in the MCT1 Ansi table WfMcT1AnsiEntry .1.3.6.1.4.1.18.3.4.8.8.1 |
wfMcT1AnsiSlotInstance ID Slot, filled in by driverro INTEGER .1.3.6.1.4.1.18.3.4.8.8.1.1 |
wfMcT1AnsiConnectorInstance ID Connector, filled in by driverro Enumeration .1.3.6.1.4.1.18.3.4.8.8.1.2 |
wfMcT1AnsiCRCCountsCounts CRC-6 error eventsro Counter .1.3.6.1.4.1.18.3.4.8.8.1.3 |
wfMcT1AnsiBPVCountsCounts bipolar violationsro Counter .1.3.6.1.4.1.18.3.4.8.8.1.4 |
wfMcT1AnsiOOFCountsCounts out-of-frame error eventsro Counter .1.3.6.1.4.1.18.3.4.8.8.1.5 |
wfMcT1AnsiFECountsCounts errors in the FPS framing patternro Counter .1.3.6.1.4.1.18.3.4.8.8.1.6 |
wfMcT1AnsiESCountsCounts errorred secondsro Counter .1.3.6.1.4.1.18.3.4.8.8.1.7 |
wfMcT1AnsiSESCountsCounts severly errorred secondsro Counter .1.3.6.1.4.1.18.3.4.8.8.1.8 |
wfMcT1AnsiUASCountscounts unavailable secondsro Counter .1.3.6.1.4.1.18.3.4.8.8.1.9 |
wfMcT1AnsiPRMR0CountsCounts PRMs that ewre received in the FDL in
the last four secondsro Counter .1.3.6.1.4.1.18.3.4.8.8.1.10 |
wfMcT1AnsiPRMR1CountsCounts PRMs that ewre received in the FDL in
the last four secondsro Counter .1.3.6.1.4.1.18.3.4.8.8.1.11 |
wfMcT1AnsiPRMR2CountsCounts PRMs that ewre received in the FDL in
the last four secondsro Counter .1.3.6.1.4.1.18.3.4.8.8.1.12 |
wfMcT1AnsiPRMR3CountsCounts PRMs that ewre received in the FDL in
the last four secondsro Counter .1.3.6.1.4.1.18.3.4.8.8.1.13 |
wfMcT1AnsiPRMESCountsCounts errorred seconds as reported in the Performance
report messagesro Counter .1.3.6.1.4.1.18.3.4.8.8.1.14 |
wfMcT1AnsiPRMSESCountsCounts severely errorred seconds as reported in the
Performance report messagesro Counter .1.3.6.1.4.1.18.3.4.8.8.1.15 |
wfMcT1AnsiPRMECountsCounts Performance report messages that are received
in errorro Counter .1.3.6.1.4.1.18.3.4.8.8.1.16 |
wfMcT1BertStatsTableBERT Counter line record - This table contains the
statistics for the BERT tester. SEQUENCE OF WfMcT1BertStatsEntry .1.3.6.1.4.1.18.3.4.8.9 |
wfMcT1BertStatsEntryAn entry in the MCT1 Bert Stats table WfMcT1BertStatsEntry .1.3.6.1.4.1.18.3.4.8.9.1 |
wfMcT1BertStatsSlotInstance ID Slot, filled in by driverro INTEGER .1.3.6.1.4.1.18.3.4.8.9.1.1 |
wfMcT1BertStatsConnectorInstance ID Connector, filled in by driverro Enumeration .1.3.6.1.4.1.18.3.4.8.9.1.2 |
wfMcT1BertStatsBitErrorsBit error counterro Counter .1.3.6.1.4.1.18.3.4.8.9.1.3 |
wfMcT1BertStatsBitsBit counterro Counter .1.3.6.1.4.1.18.3.4.8.9.1.4 |
wfMcT1ModEntryAn entry in the MCT1 Base table WfMcT1ModEntry .wfMcT1ModTable.1 |
wfMcT1ModDeleteCreate/Delete parameterrw Enumeration .wfMcT1ModTable.1.1 |
wfMcT1ModDisableEnable/Disable parameterrw Enumeration .wfMcT1ModTable.1.2 |
wfMcT1ModSlotInstance ID slot, filled in by driverro INTEGER .wfMcT1ModTable.1.3 |
wfMcT1ModPrimaryClockSpecifies the primary source for T1 transmit timing.
Both T1 ports use the same T1 transmit timing source.
The options for T1 timing source are internal timing source,
loop timing from either T1 port and an external timing
source.rw Enumeration .wfMcT1ModTable.1.4 |
wfMcT1ModSecondaryClockSpecifies the secondary source for T1 transmit timing.
During normal operation T1 transmit timing is derived
from the primary timing source. If the primary timing
source fails, the software switches to secondary timing
source.rw Enumeration .wfMcT1ModTable.1.5 |
wfMcT1ModCurrentClockIndicates the clock source currently in usero Enumeration .wfMcT1ModTable.1.6 |
wfMcT1ModExtClockOperationalIndicates whether the External clock is operationalro Enumeration .wfMcT1ModTable.1.7 |
wfMcT1ModLoop0ClockOperationalIndicates whether the timing source from port 1
is operationalro Enumeration .wfMcT1ModTable.1.8 |
wfMcT1ModLoop1ClockOperationalIndicates whether the timing source from port 2
is operationalro Enumeration .wfMcT1ModTable.1.9 |
wfMcT1ModRestartIndicates Module gate should be restarted to read
new configurationrw INTEGER .wfMcT1ModTable.1.10 |