Wellfleet-LAPB-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for Wellfleet-LAPB-MIB.
44
Objects
Active
Status
3
Dependencies
Imported Objects
Objects
44 total| Object Name |
|---|
RFC1155-SMI**********************************************************************
LAPB MIB record
********************************************************************* SEQUENCE OF WfLapbEntry .1.3.6.1.4.1.18.3.5.1.8 |
wfLapbEntryAn entry in the LAPB table WfLapbEntry .wfLapbTable.1 |
wfLapbDeleteCreate/Delete parameterrw Enumeration .wfLapbTable.1.1 |
wfLapbDisableEnable/Disable parameterrw Enumeration .wfLapbTable.1.2 |
wfLapbStateLine Driver state variable, Not Present, DSR Wait,
Init, Down, Upro Enumeration .wfLapbTable.1.3 |
wfLapbLineNumberInstance identifier, Line Number, filled in by LAPBro INTEGER .wfLapbTable.1.4 |
wfLapbLLIndexInstance identifier, Lower Layer Index, filled in by LAPBro INTEGER .wfLapbTable.1.5 |
wfLapbCctCCT number for this LAPB subsystem, it is associated with the driver
or application running underneath it.ro INTEGER .wfLapbTable.1.6 |
wfLapbStationTypeIdentifies the desired station type of this interface. A value
of DxE indicates XID enabled but not negotiation has not yet
taken place.rw Enumeration .wfLapbTable.1.7 |
wfLapbControlFieldThis parameter establishes the desired size of the
sequence numbers used to number frames.rw Enumeration .wfLapbTable.1.8 |
wfLapbN1FrameSizeThe default maximum N1 frame size desired in number of bytes
for a frame transmitted by the DxE. This excludes flags and
0 bits inserted for transparency.rw INTEGER .wfLapbTable.1.9 |
wfLapbKWindowSizeThe default transmit and receive window size for this Interface.
This is the maximum number of unacknowledged sequence frames that
may be outstanding from this DxE at any one time.rw INTEGER .wfLapbTable.1.10 |
wfLapbN2RxmitCountThe default N2 retry count indicates the number of retransmission
attempts which will be tried per frame before a line is determined
to be down. The retry count is max attempts following expiration of
the T1 timer.rw INTEGER .wfLapbTable.1.11 |
wfLapbT1AckTimerThe default T1 timer for this interface. This specifies the maximum
time in tenths of seconds to wait for an acknowledgment of a frame.rw INTEGER .wfLapbTable.1.12 |
wfLapbT2AckDelayTimerThe default T2 timer for this interface. This specifies the maximum
time in seconds to wait before sending an acknowledgment for a
sequenced frame. A value of one means there will be no delay in
acknowledgment generation.rw INTEGER .wfLapbTable.1.13 |
wfLapbT3DisconnectTimerThe T3 timer for this interface. This specifies the time in seconds
to wait before considering the link disconnected. A value of one
indicates the link will be considered disconnected upon completion of
the frame exchange to disconnect the link.rw INTEGER .wfLapbTable.1.14 |
wfLapbT4IdleTimerThe T4 timer for this interface. This specifies the maximum time in
seconds to allow without frames being exchanged on the data link.
Not implemented for this project.rw INTEGER .wfLapbTable.1.15 |
wfLapbActionInitiateThis identifies the action LAPB will take to initiate link set-up.rw Enumeration .wfLapbTable.1.16 |
wfLapbXidDisableXID enable/disable parameter. This parameter is used to enable
or disable transmission/reception of Test XID frames.rw Enumeration .wfLapbTable.1.17 |
wfLapbCommandAddressThe local command address parameter contains the DTE or DCE
value expressed as a single octet.rw Enumeration .wfLapbTable.1.18 |
wfLapbResponseAddressThe local response address parameter contains the DTE or DCE
value expressed as a single octet.rw Enumeration .wfLapbTable.1.19 |
wfLapbWanProtocolWAN protocol selection is provided via this parameter. The
supported protocols can be selected per interface.rw Enumeration .wfLapbTable.1.20 |
wfLapbRxOctetsNumber of octets received without errorro Counter .wfLapbTable.1.21 |
wfLapbRxFramesNumber of frames received without errorro Counter .wfLapbTable.1.22 |
wfLapbTxOctetsNumber of octets transmitted without errorro Counter .wfLapbTable.1.23 |
wfLapbTxFramesNumber of frames transmitted without errorro Counter .wfLapbTable.1.24 |
wfLapbReXmitsNumber of retransmission occurancesro Counter .wfLapbTable.1.25 |
wfLapbRejectsTxNumber of reject frames which were transmittedro Counter .wfLapbTable.1.26 |
wfLapbRejectsRxNumber of reject frames which were receivedro Counter .wfLapbTable.1.27 |
wfLapbFrameRejectsTxNumber of Frame Rejects transmittedro Counter .wfLapbTable.1.28 |
wfLapbFrameRejectsRxNumber of Frame Rejects receivedro Counter .wfLapbTable.1.29 |
wfLapbRRsTxNumber of Receiver Ready frames transmittedro Counter .wfLapbTable.1.30 |
wfLapbRRsRxNumber of Receiver Ready frames receivedro Counter .wfLapbTable.1.31 |
wfLapbRNRsTxNumber of Receiver Not Ready frames transmittedro Counter .wfLapbTable.1.32 |
wfLapbRNRsRxNumber of Receiver Not Ready frames receivedro Counter .wfLapbTable.1.33 |
wfLapbResetsNumber of Link Connection Resetsro Counter .wfLapbTable.1.34 |
wfLapbNormalDiscNumber of normal link disconnectionsro Counter .wfLapbTable.1.35 |
wfLapbAbnormalDiscNumber of abnormal link disconnectionsro Counter .wfLapbTable.1.36 |
wfLapbSetupAllowedNumber of successful link connectionsro Counter .wfLapbTable.1.37 |
wfLapbSetupRefusedNumber of unsuccessful link connectionsro Counter .wfLapbTable.1.38 |
wfLapbNetworkTypeThe types GOSIP and NET2 are used in conjunction with the X.25 networkrw Enumeration .wfLapbTable.1.39 |
wfLapbIdleRRFramesXID enable/disable parameter. This parameter is used to enable
or disable transmission/reception of Test XID frames.rw Enumeration .wfLapbTable.1.40 |
wfLapbClientTypeThis parameter is used to describe the client above
the LAPB protocol layer. By default, the client is the
X.25 Packet layer. Currently, the only other selection
is ipex or none.rw Enumeration .wfLapbTable.1.41 |
wfLapbRetransmitTimerThe Retransmit timer for this interface. This specifies the
maximum time in seconds to allow without retransmitting frames
after RNR and RR received on this interface.rw INTEGER .wfLapbTable.1.42 |