Wellfleet-IPEX-MIB
Detailed view of the defined objects, syntax rules, and hierarchical paths.
62
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
62 total| Object Name |
|---|
wfIpex OBJECT IDENTIFIER .1.3.6.1.4.1.18.3.5.15.1 |
RFC1155-SMI Unknown .1.3.6.1.4.1.18.3.5.15.1 |
wfIpexDeleteCreate/Delete parameter. Default is created.
Users perform an SNMP SET operation on this
object in order to create/delete IPEX.rw Enumeration .1.3.6.1.4.1.18.3.5.15.1.1 |
wfIpexDisableEnable/Disable parameter. Default is enabled.
Users perform an SNMP SET operation on this
object in order to enable/disable IPEX.rw Enumeration .1.3.6.1.4.1.18.3.5.15.1.2 |
wfIpexStateThe current state of IPEX.ro Enumeration .1.3.6.1.4.1.18.3.5.15.1.3 |
wfIpexMaxMessageSizeThe maximum client message size that IPEX accepts. The
size is in bytes.rw INTEGER .1.3.6.1.4.1.18.3.5.15.1.4 |
wfIpexInsCalledDteEnable/Disable parameter. Default is disabled.
Users perform an SNMP SET operation on this
object in order to enable/disable the support
for inserting Called DTE address.rw Enumeration .1.3.6.1.4.1.18.3.5.15.1.5 |
wfIpexInsCallingDteEnable/disable the support for transmitting the calling
DTE address over TCP tunnel. This changes the IPEX control
message header format and hence this attribute should be
enabled (only for 11.02 or up) on both ends (local & remote
routers) for proper operation. This attribute applies only
to End_to_End mode.rw Enumeration .1.3.6.1.4.1.18.3.5.15.1.6 |
wfIpexTcpRequestLimitThe maximum number of TCP requests IPEX can have pending
with TCP. Any addition requests will be queued until the
number of pending requests fall below the limit.rw INTEGER .1.3.6.1.4.1.18.3.5.15.1.7 |
wfIpexTcpRequestCheckWhen IPEX has queued TCP requests, the time period (in
milliseconds) between checking if the number of pending
TCP requests have fallen below wfIpexTcpRequestLimit.rw INTEGER .1.3.6.1.4.1.18.3.5.15.1.8 |
wfIpexSendResetRequestOnTCPUpDefault(cause code) is 0x09 and PVC_TCP sends out the Reset
Request with the cause code = 0x09 and TCP_PVC Router does not
send the Reset Request when TCP is up. If the value is changed
from the default cause code(0x09) then IPEX Gateway will send
out the Reset Request with this value when network is operational.
TCP_PVC will also send the Reset Request with this cause code
when TCP connection is up.rw INTEGER .1.3.6.1.4.1.18.3.5.15.1.9 |
wfIpexTranslateNetworkOutOfOrderDefault is 0x1d(29): Network out of order. If the value is changed
from the default cause code = 0x1d then the IPEX Gateway will
send the Reset Request with cause code specified when the network
is out of order.rw INTEGER .1.3.6.1.4.1.18.3.5.15.1.10 |
wfIpexTcpUseIpAddressEnable/Disable parameter. Default is disabled.
If set to Enabled, the IP address used for a TCP
connection will be the coresponding address for the
circuit.rw Enumeration .1.3.6.1.4.1.18.3.5.15.1.11 |
wfIpexBobEnabledThis attribute will indicate whether IPEX supports Bank
Of Bahrain enhancement. If it is enabled, only calling DTE
will be send in ASCII format in user defined area of message
header, if header type is full.rw Enumeration .1.3.6.1.4.1.18.3.5.15.1.12 |
wfIpexBobTimeoutThis attribute will indicate the timeout in milliseconds, after
which DEVICE UP message is to be send to BOB mainserver
from router, as long as this service supports BOB
functionality.rw INTEGER .1.3.6.1.4.1.18.3.5.15.1.13 |
wfIpexMaxAuditIpDefault is 25. Specify the maximum of IP address and TCP port
pairs that IPEX Audit gate can hold in its internal table when
IPEX PVC-TCP Gateway is in TCP Retry Mode. Audit gate puts
new ip address and TCP port pair to the internal table when it
tries TCP connection. IPEX Audit gate will be re-trying TCP
connections until the table is filled up. Once it is full
then it won't re-try new TCP connections. Setting zero causes
IPEX audit gate to try TCP connections without examining the
IP address and TCP port pairs had already tried out or not.rw INTEGER .1.3.6.1.4.1.18.3.5.15.1.14 |
wfIpexSessionInstanceIdOffsetForSvcDefault is 0. Specify the offset value for wfIpexSessionEntry
when instances for SVC are created. For example, when it is
set to 1023, instance ID for wfIpexSessionEntry for SVC
connections will be wfIpexSessionEntry.*.3.1024 and the next
one will be wfIpexSessionEntry.*.3.1025 and so on.
This MIB object is introduced not to assign same instance ID
to PVC and SVC when SVCs and PVCs are configured with single
circuit. Because wfIpexSessionEntry for PVCs are based on the
LCNs and the ones for SVCs are based on the order of each SVC
being created, there would be the cases that same instance IDs
are assigned to both SVC and PVC and it will cause the router
to fault. It needs to be set to the value which is greater
than the maximum LCN of the PVC connections when PVCs and SVCs
co-exist on a single circuit.rw INTEGER .1.3.6.1.4.1.18.3.5.15.1.15 |
wfIpexMappingTableA table which contains the list of mappings between TCP
connections and X.25 connections. This is the configuration
table in which each entry sets up the association between a
TCP port number and a X.25 DTE address or connection.
inst_id[] = wfIpexMappingSrcConnCct wfIpexMappingSrcConnType
wfIpexMappingID SEQUENCE OF WfIpexMappingEntry .1.3.6.1.4.1.18.3.5.15.2 |
wfIpexMappingEntryAn entry in wfIpexMappingTable. WfIpexMappingEntry .1.3.6.1.4.1.18.3.5.15.2.1 |
wfIpexMappingDeleteCreate/Delete attribute. Default is created.
Users perform an SNMP SET operation on this object in
order to create/delete a translation mapping record.rw Enumeration .1.3.6.1.4.1.18.3.5.15.2.1.1 |
wfIpexMappingDisableEnables or Disables this Mapping entry.
Setting this attribute to DISABLED will disconnect
all active Sessions pertaining to this Mapping entryrw Enumeration .1.3.6.1.4.1.18.3.5.15.2.1.2 |
wfIpexMappingSrcConnCctThe circuit from which the connection attempt is
received that initiates a translation session.ro INTEGER .1.3.6.1.4.1.18.3.5.15.2.1.3 |
wfIpexMappingSrcConnTypeDefines the type of original connection attempt.
Whether it is a PVC, SVC, DCE_SVC, LAPB or TCPro Enumeration .1.3.6.1.4.1.18.3.5.15.2.1.4 |
wfIpexMappingID1The translation mapping identifier which identifies the
remote connection of the translation session. This is
an identifier that is available from the incoming
connection attempt.
The meaning of this object (wfIpexMappingID1) and the
next object (wfIpexMappingID2) is dependent on the
value of wfIpexMappingSrcConnType.
SrcConnType ID1 ID2
pvc(1) LCN value 0 (Null)
svc(2) 0 Called X.121 Address
dcesvc(4) 0 0 (Null)
lapb(8) 0 0 (Null)
tcp(16) Port Number 0 (Null)ro INTEGER .1.3.6.1.4.1.18.3.5.15.2.1.5 |
wfIpexMappingID2(See description for wfIpexMappingID1 above)ro OCTET STRING .1.3.6.1.4.1.18.3.5.15.2.1.6 |
wfIpexMappingDstConnCctThe circuit from which the connection to the destination
is to be established to set up a translation session.rw INTEGER .1.3.6.1.4.1.18.3.5.15.2.1.7 |
wfIpexMappingDstConnTypeDefines type of connection at the destination end. Whether
it is a PVC, SVC, DCE_SVC, LAPB or TCPrw Enumeration .1.3.6.1.4.1.18.3.5.15.2.1.8 |
wfIpexMappingLocalDTEAddrThe Local DTE address (identifies the X.121 address
of the X.25 interface on the IPEX). This attribute
is only used in the case of a SVC connection initiated
from the IPEX to the terminalrw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.18.3.5.15.2.1.9 |
wfIpexMappingRemoteDTEAddrThe Remote DTE address (identifies the X.121 address
of the X.25 interface on the terminal). This attribute
is only used in the case of a SVC connection initiated
from the IPEX to the terminalrw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.18.3.5.15.2.1.10 |
wfIpexMappingPvcLcnThe LCN of the PVC connection from the IPEX to the
terminal (identifies the channel to be used to reset
the PVC connection. This attribute * is only used
in the case of a PVC connection initiated from the
IPEX to the terminalrw INTEGER .1.3.6.1.4.1.18.3.5.15.2.1.11 |
wfIpexMappingRemoteIpAddrThe IP address of the remote host with which
this translation session is established. This
attribute is only used in the case of a TCP
connection initiated from the IPEX to a hostrw IpAddress .1.3.6.1.4.1.18.3.5.15.2.1.12 |
wfIpexMappingRemoteTcpPortThe remote TCP port number in the host to be used
to establish a TCP connection from the IPEX to the
host server. This attribute is only used in the
case of a TCP connection initiated from the IPEX
to a hostrw INTEGER .1.3.6.1.4.1.18.3.5.15.2.1.13 |
wfIpexMappingQueueSizeThe size of the IPEX queues used for transfering data
between TCP and X.25. The size is in bytes.rw INTEGER .1.3.6.1.4.1.18.3.5.15.2.1.14 |
wfIpexMappingSlotNumberThe slot of the access (X.25 or LAPB) circuit
on which the X.25 or LAPB connections will be
established.rw INTEGER .1.3.6.1.4.1.18.3.5.15.2.1.15 |
wfIpexMappingCtrlModeLocal mode configuration terminates X.25 at the router
interface. The end2end mode configuration allows X.25
signalling and data to operate between two remote X.25
networks, using the router to translate both call control
and data over a TCP/IP network. The gateway mode terminates
X.25 at the router interface, but allows the user to configure
3 message header types at the TCP application layer. These
header values are described in wfIpexMappingMsgHdrType.rw Enumeration .1.3.6.1.4.1.18.3.5.15.2.1.16 |
wfIpexMappingX25CUDFThe X.25 Call User Data field (CUDF) in a X.25 Call
Request packet header. This attribute is only used
in the case of a SVC connection initiated from the
IPEX to the terminal. It is used as the network
layer protocol identifier of the X.25 connection.rw OCTET STRING .1.3.6.1.4.1.18.3.5.15.2.1.17 |
wfIpexMappingIdleTimerIdle session timeout period, in seconds. If an established
TCP connection remains inactive for this interval, KEEPALIVE
messages will be sent to the peer (if the Keepalive Timer is
non-zero). Setting the Idle Timer to zero disables the
keepalive feature.rw INTEGER .1.3.6.1.4.1.18.3.5.15.2.1.18 |
wfIpexMappingKeepaliveTimerKEEPALIVE retransmit timeout period, in seconds. This is
the interval at which unacknowledged KEEPALIVE messages will
be retransmitted. If the Idle Timer is set to zero, this
timer ignored. If the Idle Timer is non-zero and this timer
IS zero, no KEEPALIVEs are sent and the session is terminated
upon expiration of the Idle Timer.rw INTEGER .1.3.6.1.4.1.18.3.5.15.2.1.19 |
wfIpexMappingKeepaliveRetriesNumber of unacknowledged KEEPALIVE messages retransmitted
before the TCP session is terminated. If this count is set
to zero, only one KEEPALIVE message will be sent.rw INTEGER .1.3.6.1.4.1.18.3.5.15.2.1.20 |
wfIpexMappingTraceThis object is a bitmask, setting the low order bit enables
tracing of IPEX internal events. Setting other individual bit
postions disable logging of internal IPEX events. Values may
be added together to disable multiple message groups.
Hex Dec
Value Value Message/Event
-
0x0001 1 Enable IPEX tracing.
0x0002 2 Data packets from IPEX to X.25.
0x0004 4 Data packets from X.25 to IPEX.
0x0008 8 Window updates from X.25.
0x0010 16 Data from TCP to IPEX.
0x0020 32 Window updates from TCP.
0x0040 64 Window requests from TCP.rw INTEGER .1.3.6.1.4.1.18.3.5.15.2.1.21 |
wfIpexMappingMsgHdrTypeThis attribute enables the Message Boundary Protocol.
When enabled, this bit is used to mark the boundary
of TCP application data that is consistent with
Gateway Operation. The first three message header types
are used only with wfIpexMappingCtlMode in gateway mode.
The default value is used with wfIpexMappingCtlMode in
the local or end2end mode of operation.
NONE = Msg Boundary Protocol is off, no msg header.
SHORT = Msg header condtains a 2-Byte length field.
LONG = Msg header contains a 1-Byte type, 1-Byte
version, and a 2-Byte length fields.
FULL = Msg Header contains a 2-Byte length1 field,
1-Byte Version field, 1-Byte Type field and,
a 1-Byte length2 fieldrw Enumeration .1.3.6.1.4.1.18.3.5.15.2.1.22 |
wfIpexMappingRemoteBackupIpThe IP address of the remote host with which
this translation session is established. This
attribute is only used in the case of a TCP
connection with the primary remote IP address
(wfIpexMappingRemoteIpAddr) failed.rw IpAddress .1.3.6.1.4.1.18.3.5.15.2.1.23 |
wfIpexMappingXlateCallingX121If this attribute is configured then insert this X.121
addr as the calling addr in the Call request pkt.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.18.3.5.15.2.1.24 |
wfIpexMappingTcpMaxRetryThe maximum number of attempts that PVC-TCP will make to
re-establish the connection to the remote peer. The
TCP Retry takes place every 15 seconds hence default
setting will perform the TCP Retry forever.rw INTEGER .1.3.6.1.4.1.18.3.5.15.2.1.25 |
wfIpexMappingCfgLocalIpAddrThe IP address on the router to use as the source of the
TCP session. This attribute is only used in the case of
a TCP connection initiated from the IPEX to a hostrw IpAddress .1.3.6.1.4.1.18.3.5.15.2.1.26 |
wfIpexMappingRemoteBackupTcpPortThe TCP port of the remote host with which
this translation session is established. This
attribute is only used in the case of a TCP
connection with the primary remote IP address
(wfIpexMappingRemoteIpAddr) failed.rw INTEGER .1.3.6.1.4.1.18.3.5.15.2.1.27 |
wfIpexSessionTableA table that contains the information about the
current active IPEX translation sessions. The
status and statistics information related to each
translation session is provided here.
inst_id[] = wfIpexSessionIndex SEQUENCE OF WfIpexSessionEntry .1.3.6.1.4.1.18.3.5.15.3 |
wfIpexSessionEntryAn entry in wfIpexSession. WfIpexSessionEntry .1.3.6.1.4.1.18.3.5.15.3.1 |
wfIpexSessionStateThe IPEX state of this translation session. These are the
steady states of the IPEX state machine. Transition
states are not reflected.ro Enumeration .1.3.6.1.4.1.18.3.5.15.3.1.1 |
wfIpexSessionSrcConnCctThe circuit from which the original connection attempt
is received that initiated a translation session.ro INTEGER .1.3.6.1.4.1.18.3.5.15.3.1.2 |
wfIpexSessionIndexThe index of this translation sessionro INTEGER .1.3.6.1.4.1.18.3.5.15.3.1.3 |
wfIpexSessionSrcConnTypeDefines type of original connection attempt. Whether
it is a PVC, SVC, DCE_SVC, LAPB or TCPro Enumeration .1.3.6.1.4.1.18.3.5.15.3.1.4 |
wfIpexSessionDstConnCctThe circuit from which the connection at the destination
to be established to set up a translation session.ro INTEGER .1.3.6.1.4.1.18.3.5.15.3.1.5 |
wfIpexSessionDstConnTypeDefines type of connection at the destination end. Whether
it is a PVC, SVC, DCE_SVC, LAPB or TCPro Enumeration .1.3.6.1.4.1.18.3.5.15.3.1.6 |
wfIpexSessionLocalDTEAddrThe Local DTE address (identifies the X.121 address
of the X.25 interface on the IPEX). This attribute
is only used in the case of a SVC connection initiated
from the IPEX to the terminalro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.18.3.5.15.3.1.7 |
wfIpexSessionRemoteDTEAddrThe Remote DTE address (identifies the X.121 address
of the X.25 interface on the terminal). This attribute
is only used in the case of a SVC connection initiated
from the IPEX to the terminalro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.18.3.5.15.3.1.8 |
wfIpexSessionLCNThe LCN of the PVC (identifies the channel to be used
to establish a PVC connection from the IPEX to the
terminalro INTEGER .1.3.6.1.4.1.18.3.5.15.3.1.9 |
wfIpexSessionLocalIpAddrThe IP address of an interface on the IPEX to be
used to establish a TCP connection with the host
server. This attribute is only used in the case
of a TCP connection initiated from the IPEX to a
hostro IpAddress .1.3.6.1.4.1.18.3.5.15.3.1.10 |
wfIpexSessionLocalTcpPortThe local TCP port number in the IPEX to be used
to establish a TCP connection to the host server
This attribute is only used in the case of a TCP
connection initiated from the IPEX to a hostro INTEGER .1.3.6.1.4.1.18.3.5.15.3.1.11 |
wfIpexSessionRemoteIpAddrThe IP address of the remote host with which
this translation session is established. This
attribute is only used in the case of a TCP
connection initiated from the IPEX to a hostro IpAddress .1.3.6.1.4.1.18.3.5.15.3.1.12 |
wfIpexSessionRemoteTcpPortThe remote TCP port number in the host to be used
to establish a TCP connection from the IPEX to the
host server. This attribute is only used in the
case of a TCP connection initiated from the IPEX
to a hostro INTEGER .1.3.6.1.4.1.18.3.5.15.3.1.13 |
wfIpexSessionQueueSizeThe size of the IPEX queues used for transfering data
between IPEX and TCP. The size is in bytes.ro INTEGER .1.3.6.1.4.1.18.3.5.15.3.1.14 |