Wellfleet-FR-MIB
Detailed view of the defined objects, syntax rules, and hierarchical paths.
50
Objects
Active
Status
5
Dependencies
Imported Objects
Objects
50 total| Object Name |
|---|
RFC1155-SMIThe Parameters for the Data Link Connection Management Interface SEQUENCE OF WfFrDlcmiEntry .1.3.6.1.4.1.18.3.5.9.1.1 |
wfFrDlcmiEntryThe parameters for a particular Data Link Connection Management Interface WfFrDlcmiEntry .1.3.6.1.4.1.18.3.5.9.1.1.1 |
wfFr1DlcmiDeleteIndication to delete this frame relay interfacerw Enumeration .1.3.6.1.4.1.18.3.5.9.1.1.1.1 |
wfFr1DlcmiDisableIndicates when a dlcmi entry is to be enabled or disabled.rw Enumeration .1.3.6.1.4.1.18.3.5.9.1.1.1.2 |
wfFr1DlcmiStateThe current state of Frame Relay. The not present state is not actually
valid except when the record is first added. It is included for
consistency.ro Enumeration .1.3.6.1.4.1.18.3.5.9.1.1.1.3 |
wfFr1DlcmiCircuitInstance identifier. The circuit number of this entryro INTEGER .1.3.6.1.4.1.18.3.5.9.1.1.1.4 |
wfFr1DlcmiManagementTypeThis variable indicates which Data Link Connection Management
scheme is active (and by implication, what DLCI it uses).rw Enumeration .1.3.6.1.4.1.18.3.5.9.1.1.1.5 |
wfFr1DlcmiStatusIndicates the status of the interface.
FR1_STATUS_START is the state during rebooting or initial
start of circuit
FR1_STATUS_RUNNING1 is the sate after the circuit is up (either LMI
successful or there is no DLCMI and the system just comes up).
FR1_STATUS_FAULT is a transient state indicating that errors have
caused the circuit to be disabled until DLCMI recovery.
FR1_STATUS_RECOVERED indicates that an the system has been in the
FR_STATUS_FAULT mode before, but has since recovered.ro Enumeration .1.3.6.1.4.1.18.3.5.9.1.1.1.6 |
wfFr1DlcmiAddressThis states which address format is in use on the FR interface.
The default is Q922rw Enumeration .1.3.6.1.4.1.18.3.5.9.1.1.1.7 |
wfFr1DlcmiAddressLenThis variable states the address length in octets. In the case
of Q922 format, the length indicates the entire length of the
address includeding the control portion.rw Enumeration .1.3.6.1.4.1.18.3.5.9.1.1.1.8 |
wfFr1DlcmiPollingIntervalThe number of seconds between successive status enquiry messagesrw INTEGER .1.3.6.1.4.1.18.3.5.9.1.1.1.9 |
wfFr1DlcmiFullEnquiryIntervalThe number of status enquiry intervals that pass before issuance
of a full status enquiry message.rw INTEGER .1.3.6.1.4.1.18.3.5.9.1.1.1.10 |
wfFr1DlcmiErrorThresholdThis is the maximum number of unanswered Status Enquiries the
equipment shall accept before declaring the interface down.rw INTEGER .1.3.6.1.4.1.18.3.5.9.1.1.1.11 |
wfFr1DlcmiMonitoredEventsThis is the number of status polling intervals over
which the error threshold is counted. For example, if
within 'MonitoredEvents' number of events the station
receives 'ErrorThreshold' number of errors, the
interface is marked as down.rw INTEGER .1.3.6.1.4.1.18.3.5.9.1.1.1.12 |
wfFr1DlcmiMaxSupportedVCsThe maximum number of Virtual Circuits allowed for
this interface. Usually dictated by the Frame Relay
network. The system sets this initially.ro INTEGER .1.3.6.1.4.1.18.3.5.9.1.1.1.13 |
wfFr1DlcmiMulticastThis indicates whether the frame relay provider offers a multicastrw Enumeration .1.3.6.1.4.1.18.3.5.9.1.1.1.14 |
wfFr1DlcmiSeqCountThis station's sequence counter. It represents the next
value to send.ro INTEGER .1.3.6.1.4.1.18.3.5.9.1.1.1.15 |
wfFr1DlcmiLastReceivedThe sequence number just received from the switch.ro INTEGER .1.3.6.1.4.1.18.3.5.9.1.1.1.16 |
wfFr1DlcmiPassiveSeqCountThis station's sequence counter for answering status enquiry.ro INTEGER .1.3.6.1.4.1.18.3.5.9.1.1.1.17 |
wfFr1DlcmiPassiveReceivedThe sequence number just received from the enquring station.ro INTEGER .1.3.6.1.4.1.18.3.5.9.1.1.1.18 |
wfFr1DlcmiPollsThis is the counter of where we are in the polling cycle.ro INTEGER .1.3.6.1.4.1.18.3.5.9.1.1.1.19 |
wfFr1DlcmiAlarmTimerThis is a counter of 1/2 second timeouts. When it reaches
2 x the polling interval, an enquiry message is sent.ro INTEGER .1.3.6.1.4.1.18.3.5.9.1.1.1.20 |
wfFr1ErrTypeIndicate the type of the last specific monitored error.ro Enumeration .1.3.6.1.4.1.18.3.5.9.1.1.1.21 |
wfFr1ErrDataContains as much of the error packet as possible.ro OCTET STRING .1.3.6.1.4.1.18.3.5.9.1.1.1.22 |
wfFr1ErrTimeThe time the last error occurred.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.18.3.5.9.1.1.1.23 |
wfFr1ErrDiscardsThe number of inbound frames dropped because of format or other
errors or because the VC was not known.ro Counter .1.3.6.1.4.1.18.3.5.9.1.1.1.24 |
wfFr1ErrDropsThe number of outbound frames dropped. Usually this is due the
specified DLCI being unknown or a broadcast packet is too longro Counter .1.3.6.1.4.1.18.3.5.9.1.1.1.25 |
wfFrCircuitTableFrame Relay Circuit table gives information about a virtual circuits. SEQUENCE OF WfFrCircuitEntry .1.3.6.1.4.1.18.3.5.9.1.2 |
wfFrCircuitEntryAn entry in the Frame Relay Circuit table. WfFrCircuitEntry .1.3.6.1.4.1.18.3.5.9.1.2.1 |
wfFr1CircuitDeleteIndication to delete this frame relay interface.rw Enumeration .1.3.6.1.4.1.18.3.5.9.1.2.1.1 |
wfFr1CircuitNumberInstance identifier. The circuit number of this interface.ro INTEGER .1.3.6.1.4.1.18.3.5.9.1.2.1.2 |
wfFr1CircuitDlciInstance identifier. This indicates which virtual circuit.ro Enumeration .1.3.6.1.4.1.18.3.5.9.1.2.1.3 |
wfFr1CircuitStateIndicates the state of the particular virtual circuit.ro Enumeration .1.3.6.1.4.1.18.3.5.9.1.2.1.4 |
wfFr1CircuitStateSetUser access for setting the state of a virtual circuitrw Enumeration .1.3.6.1.4.1.18.3.5.9.1.2.1.5 |
wfFr1CircuitReceivedFECNsNumber of frames received indicating forward congestion.ro Counter .1.3.6.1.4.1.18.3.5.9.1.2.1.6 |
wfFr1CircuitReceivedBECNsNumber of frames received indicating backward congestion.ro Counter .1.3.6.1.4.1.18.3.5.9.1.2.1.7 |
wfFr1CircuitSentFramesThe number of frames sent from this virtual circuit.ro Counter .1.3.6.1.4.1.18.3.5.9.1.2.1.8 |
wfFr1CircuitSentOctetsThe number of octets sent from this virtual circuit.ro Counter .1.3.6.1.4.1.18.3.5.9.1.2.1.9 |
wfFr1CircuitReceivedFramesThe number of frames received from this virtual circuit.ro Counter .1.3.6.1.4.1.18.3.5.9.1.2.1.10 |
wfFr1CircuitReceivedOctetsThe number of octets received from this virtual circuit.ro Counter .1.3.6.1.4.1.18.3.5.9.1.2.1.11 |
wfFr1CircuitCreationTimeThe value of sysUpTime when the vc was created.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.18.3.5.9.1.2.1.12 |
wfFr1CircuitLastTimeChangeThe value of sysUpTime when last there was a change in vc state.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.18.3.5.9.1.2.1.13 |
wfFr1CircuitCommittedBurstIndicates the maximum amount of data, in bits, that the network
agrees to transfer under normal conditions, during the measurement
interval. Wellfleet does not presently support this.rw INTEGER .1.3.6.1.4.1.18.3.5.9.1.2.1.14 |
wfFr1CircuitExcessBurstIndicates teh maximum amount of uncommitted data bits that the network
will attempt to deliver over the measurement interval. Wellfleet
does not presently support this.rw INTEGER .1.3.6.1.4.1.18.3.5.9.1.2.1.15 |
wfFr1CircuitThroughputThis is the average number of 'Frame Relay Information Field'
bits transferred per second across a user network interface in one
direction, measured over the measurement interval. Wellfleet
does not presently support this.rw INTEGER .1.3.6.1.4.1.18.3.5.9.1.2.1.16 |
wfFr1CircuitMulticastIndicates whether this DLCI is used for multicast or single destination.rw Enumeration .1.3.6.1.4.1.18.3.5.9.1.2.1.17 |
wfFr1CircuitDiscardsThe number of inbound frames discarded because of format errors,
because the VC is inactive or because the protocol was not registered
for this circuit.ro Counter .1.3.6.1.4.1.18.3.5.9.1.2.1.18 |
wfFr1CircuitDropsIndicates how many outbound frames were dropped. Usually these are
dropped because the VC is not active.ro Counter .1.3.6.1.4.1.18.3.5.9.1.2.1.19 |
wfFr1CircuitSubCctCircuit number to use for this VC when configured in hybrid
(for bridging) or direct access (VC as a circuit) mode.rw INTEGER .1.3.6.1.4.1.18.3.5.9.1.2.1.20 |
wfFr1CircuitModeThe mode of the given VC.
GROUP - treats the VC as one of many vc's on a circuit.
HYBRID - treats the VC as one of many vc's on a circuit for
protocol traffic, but as a separate circuit for bridging.
DIRECT - treats the VC as a separate circuit for all applications.rw Enumeration .1.3.6.1.4.1.18.3.5.9.1.2.1.21 |