Wellfleet-DVMRP-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for Wellfleet-DVMRP-MIB.
130
Objects
Active
Status
3
Dependencies
Imported Objects
Objects
130 total| Object Name |
|---|
wfDvmrpBase OBJECT IDENTIFIER .1.3.6.1.4.1.18.3.5.3.12.1 |
RFC1155-SMI Unknown .1.3.6.1.4.1.18.3.5.3.12.1 |
wfDvmrpBaseCreateThis entry will provide the base configuration for the DVMRP
multicast support on the router.rw Enumeration .1.3.6.1.4.1.18.3.5.3.12.1.1 |
wfDvmrpBaseEnableEnable or disable DVMRP support in routerrw Enumeration .1.3.6.1.4.1.18.3.5.3.12.1.2 |
wfDvmrpBaseStateState of DVMRP base modulero Enumeration .1.3.6.1.4.1.18.3.5.3.12.1.3 |
wfDvmrpBaseFullUpdateIntervalFull update interval. This value specifies, in seconds, how
often routing messages containing complete routing tables are
sent.rw INTEGER .1.3.6.1.4.1.18.3.5.3.12.1.4 |
wfDvmrpBaseTriggeredUpdateIntervalTriggered update interval. This value specifies, in seconds,
how often triggered routing messages are sent; this represents
the minimum amount of time between these type of messages.
Triggered updates are sent between full update; the timers
restart when a full update is sent so this value should be less
than the full update rate.rw INTEGER .1.3.6.1.4.1.18.3.5.3.12.1.5 |
wfDvmrpBaseLeafTimeoutLeaf timeout. This value specifies, in seconds, the
virtual interface hold down timer.rw INTEGER .1.3.6.1.4.1.18.3.5.3.12.1.6 |
wfDvmrpBaseNeighborTimeoutNeighbor timeout. This value specifies, in seconds, how
long a router neighbor is considered 'up' without confirmation.rw INTEGER .1.3.6.1.4.1.18.3.5.3.12.1.7 |
wfDvmrpBaseRouteExpirationTimeoutRoute Expiration timeout. This value specifies, in
seconds, how long a route is considered valid without
confirmation; this represents the duration of time that this
route will be used.rw INTEGER .1.3.6.1.4.1.18.3.5.3.12.1.8 |
wfDvmrpBaseGarbageTimeoutGarbage timeout. This value specifies, in seconds, how
long a route exists without confirmation; this represents the
duration of time that this route will be included in routing
updates. This value must be greater than the route expiration
timeout.rw INTEGER .1.3.6.1.4.1.18.3.5.3.12.1.9 |
wfDvmrpBaseEstimatedRoutesEstimated number of routes, per slot. This is used for
pre-allocating routing tables. Note that routes are kept on a
per-source network basis, independent of multicast group. This number
must include a route for every local network that has a CCT configured
for multicasting.rw INTEGER .1.3.6.1.4.1.18.3.5.3.12.1.10 |
wfDvmrpBaseNeighborProbeIntervalNeighbor probe interval: how often to send a probe on VIFsrw INTEGER .1.3.6.1.4.1.18.3.5.3.12.1.11 |
wfDvmrpBaseRouteSwitchTimeoutRoute switch timeout. How long to wait, without receiving a subsequent route update
from the original neighbor, before switching to a different neighbor.rw INTEGER .1.3.6.1.4.1.18.3.5.3.12.1.12 |
wfDvmrpBaseActualRoutesCount of number of entries currently in route tablero INTEGER .1.3.6.1.4.1.18.3.5.3.12.1.13 |
wfDvmrpBaseDebugLevelTurn DVMRP log ON or OFF for DVMRP debuging messages
The levels are:
NO_DISPLAY_LOG 0x0001 - Reserved
ROUTE_UPDATE_LOG 0x0002 - Displays all routing table events
CACHE_ADD_LOG 0x0004 - Displays events relating to addition of
cache entry by the cache gate
CACHE_DELETE_LOG 0x0008 - Displays all events relating to deletion
of cache entry
CACHE_CHANGE_LOG 0x0010 - Displays all events relating to updates of
cache entries
CACHE_DATA_LOG 0x0020 - obsolete
PRUNE_MSG_LOG 0x0040 - Display router received pruning related
messages, including prunes, grafts,
graft_acks, and neighbor reset
PRUNE_XMIT_LOG 0x0080 - Display a messaged when a initial prune
state is established for a (src, group).
IGMP_COM_LOG 0x0100 - Display communication events between IGMP
and DVMRP, events including some hosts
joining a group, and all hosts leaving a
group.
DVMRP_XMIT_LOG 0x0200 - Display transmission events by the router,
e.g, prune, grafts...
CACHE_NO_GH_LOG 0x0400 - Display buffer forwarding to non-existing main or remote cache gate.
CACHE_DBG_LOG 0x0800 - Display general debugging messaages
MEM_DBG_LOG 0x1000 - Display dvmrp memory usage activities
INTEROP_DBG_LOG 0x2000 - Display dvmrp mospf debug
CACHE_BASE_ADD_LOG 0x4000 - Obsolete
CACHE_VIF_ADD_LOG 0x8000 - Obsolete
CACHE_BASE_DELETE_LOG 0x10000 - Obsolete
CACHE_VIF_DELETE_LOG 0x20000 - Obsolete
MTRACE_UPDATE_LOG 0x40000 - Displays mtrace update info
NEIGHBOR_UPDATE_LOG 0x80000 - Display events relating to
addition, deletion and update of
neighbor's info
MTM_INTERFACE_LOG 0x100000 - Display events relating to MTM-DVMRP
interface, events as MTM inbound,
outbound interact with DVMRP and entries
deletion/addition.
ROUTE_ADD_LOG 0x200000 -
ROUTE_DEL_LOG 0x400000 -
REMOTE_CACHE_ADD_LOG 0x800000 - Display addition event for the
outgoing interface of (source, group)
cache entry
REMOTE_CACHE_DELETE_LOG 0x1000000 - Display deletion event for the
outgoing interface of (source, group)
cache entry
RX_CONFLICT_ROUTE_INFO_LOG 0x2000000 - Display received conflict
route informationrw Gauge .1.3.6.1.4.1.18.3.5.3.12.1.14 |
wfDvmrpBasePruningEnableEnable or Disable Pruning functionality at the Base levelrw Enumeration .1.3.6.1.4.1.18.3.5.3.12.1.15 |
wfDvmrpBaseFragmentMtuThresholdthe default value is the CSMACD_MTU, and the MINiMUN is
X25_DDN_MTU. Both are taken from dp.hrwobsolete INTEGER .1.3.6.1.4.1.18.3.5.3.12.1.16 |
wfDvmrpBaseMaxRoutesMax number of routes, per slot. This is used to limit
the size of routing tables. Note that routes are kept on a
per-source network basis, independent of multicast group. This number
must include a route for every local network that has a CCT configured
for multicasting.rw INTEGER .1.3.6.1.4.1.18.3.5.3.12.1.17 |
wfDvmrpBasePolicyEnableEnable or Disable route policy functionality at the Base levelrwobsolete Enumeration .1.3.6.1.4.1.18.3.5.3.12.1.18 |
wfDvmrpBaseHolddownEnableEnable or Disable holddown of deleted routes.rw Enumeration .1.3.6.1.4.1.18.3.5.3.12.1.19 |
wfDvmrpCircuitEntryTableCircuit virtual interfaces (aka physical VIFs) SEQUENCE OF WfDvmrpCircuitEntry .1.3.6.1.4.1.18.3.5.3.12.2 |
wfDvmrpCircuitEntryOne instance of this object exists for every CCT that supports
this feature. The instance ID for this object will be the circuit
number. WfDvmrpCircuitEntry .1.3.6.1.4.1.18.3.5.3.12.2.1 |
wfDvmrpCircuitCreateCreate or deleterw Enumeration .1.3.6.1.4.1.18.3.5.3.12.2.1.1 |
wfDvmrpCircuitEnableEnable or disable DVMRP on this circuitrw Enumeration .1.3.6.1.4.1.18.3.5.3.12.2.1.2 |
wfDvmrpCircuitStateThe current state of the DVMRP interface. Invalid
indicates an error in processing the configuration record.ro Enumeration .1.3.6.1.4.1.18.3.5.3.12.2.1.3 |
wfDvmrpCircuitCCTThis circuit number.ro INTEGER .1.3.6.1.4.1.18.3.5.3.12.2.1.4 |
wfDvmrpCircuitRouteEnableEnable/disble this circuit for routing. If enabled, this
circuit will be used to propogate routing information,
information about this circuit will be incorporated into routing
updates, and multicast datagrams will be forwarded 'in native
mode' (e.g. as multicast datagrams) via this circuit. If
disabled, this circuit exists only to support unicast tunnels; in
this case, all other paramters are ignored.rw Enumeration .1.3.6.1.4.1.18.3.5.3.12.2.1.5 |
wfDvmrpCircuitMetricMetric. This value represents the cost of this interface;
the cost of using this hop. This value must be smaller than the
route infinity valuerw INTEGER .1.3.6.1.4.1.18.3.5.3.12.2.1.6 |
wfDvmrpCircuitRouteThresholdThreshold. This value can be used to filter out datagrams
that are being forwarded to a neighboring router; if the IP TTL
is not >= the threshold, the datagram is dropped by this routerrw INTEGER .1.3.6.1.4.1.18.3.5.3.12.2.1.7 |
wfDvmrpCircuitInPktsNumber of datagrams received on this interfacero Counter .1.3.6.1.4.1.18.3.5.3.12.2.1.8 |
wfDvmrpCircuitOutPktsNumber of datagrams send on this interfacero Counter .1.3.6.1.4.1.18.3.5.3.12.2.1.9 |
wfDvmrpCircuitInRouteUpdatesNumber of DVMRP route update messages receivedro Counter .1.3.6.1.4.1.18.3.5.3.12.2.1.10 |
wfDvmrpCircuitOutRouteUpdatesNumber of DVMRP route update messages sentro Counter .1.3.6.1.4.1.18.3.5.3.12.2.1.11 |
wfDvmrpCircuitInPktDiscardsNumber of inbound datagrams discarded due to route not foundro Counter .1.3.6.1.4.1.18.3.5.3.12.2.1.12 |
wfDvmrpCircuitOutPktDiscardsNumber of outbound datagrams discarded due to route not foundro Counter .1.3.6.1.4.1.18.3.5.3.12.2.1.13 |
wfDvmrpCircuitFwdCacheSizeMaximum number of entries allowed in the Forwarding table
at one time. there is a Forwarding table per vifrw INTEGER .1.3.6.1.4.1.18.3.5.3.12.2.1.14 |
wfDvmrpCircuitFwdCacheTTLThe time_to_live for the Forwarding table entries in seconds .rw INTEGER .1.3.6.1.4.1.18.3.5.3.12.2.1.15 |
wfDvmrpCircuitAdvertiseSelfIf enabled the router will advertise itself as one of
the source net. If not enabled the router will not advertise
itself as one of the source net.rw Enumeration .1.3.6.1.4.1.18.3.5.3.12.2.1.16 |
wfDvmrpCircuitFwdCacheEntriesThe most up to date number of entries in the forwarding cachero INTEGER .1.3.6.1.4.1.18.3.5.3.12.2.1.17 |
wfDvmrpCircuitInPrunePktsNumber of PRUNE datagrams received on this interfacero Counter .1.3.6.1.4.1.18.3.5.3.12.2.1.18 |
wfDvmrpCircuitOutPrunePktsNumber of PRUNE datagrams send on this interfacero Counter .1.3.6.1.4.1.18.3.5.3.12.2.1.19 |
wfDvmrpCircuitInGraftPktsNumber of GRAFT datagrams received on this interfacero Counter .1.3.6.1.4.1.18.3.5.3.12.2.1.20 |
wfDvmrpCircuitOutGraftPktsNumber of GRAFT datagrams send on this interfacero Counter .1.3.6.1.4.1.18.3.5.3.12.2.1.21 |
wfDvmrpCircuitInGraftAckPktsNumber of GRAFT_ACK datagrams received on this interfacero Counter .1.3.6.1.4.1.18.3.5.3.12.2.1.22 |
wfDvmrpCircuitOutGraftAckPktsNumber of GRAFT_ACK datagrams send on this interfacero Counter .1.3.6.1.4.1.18.3.5.3.12.2.1.23 |
wfDvmrpCircuitDefaultRouteSupplyenabled : Send the default route, 0.0.0.0 if learned,
form this interface.
disabled: no default route is sent from this interface.
generate: generate default route, 0.0.0.0 from this
interface.rw Enumeration .1.3.6.1.4.1.18.3.5.3.12.2.1.24 |
wfDvmrpCircuitDefaultRouteListenReceive the default route, 0.0.0.0 on this interfacerw Enumeration .1.3.6.1.4.1.18.3.5.3.12.2.1.25 |
wfDvmrpCircuitReportDependProbeThis is to control accepting the route report. According to
the protocol, dvmrp should send probe packet before sending
the route report packet to the neighbors. But some vendor
implementation did not send probes before sending reports.
Enable: only process the routes from the neighbor sending
probes. Disable: No Dependency (no restriction).rw Enumeration .1.3.6.1.4.1.18.3.5.3.12.2.1.26 |
wfDvmrpCircuitPruneLifeTimeThe life time of the prune message the router sends
to its neighbor in seconds.rw INTEGER .1.3.6.1.4.1.18.3.5.3.12.2.1.27 |
wfDvmrpCircuitAcceptAggregateRoutesCount of number of routes received have been
aggregated to the specific aggregate route currently
in route table for this interface.ro INTEGER .1.3.6.1.4.1.18.3.5.3.12.2.1.28 |
wfDvmrpCircuitAnnounceAggregatedRoutesCount of number of routes have been aggregated to
the specific aggregate route for advertisement currently
in route table for this interface.ro INTEGER .1.3.6.1.4.1.18.3.5.3.12.2.1.29 |
wfDvmrpTunnelEntryTableTunnel virtual interfaces SEQUENCE OF WfDvmrpTunnelEntry .1.3.6.1.4.1.18.3.5.3.12.3 |
wfDvmrpTunnelEntryThis object is used to specify the set of 'multicast tunnels',
unicast pipes that are used to send IP multicast datagrams to
remote network multicast routers via intermediate routers that
may not support this style of IP multicasting. One instance of
this object exists for every separate tunnel destination. The
instance identifier is the IP address of the
remote router neighbor and the local circuit number. WfDvmrpTunnelEntry .1.3.6.1.4.1.18.3.5.3.12.3.1 |
wfDvmrpTunnelCreatecreate/deleterw Enumeration .1.3.6.1.4.1.18.3.5.3.12.3.1.1 |
wfDvmrpTunnelEnableenable/disable this tunnel interfacerw Enumeration .1.3.6.1.4.1.18.3.5.3.12.3.1.2 |
wfDvmrpTunnelStateThe current state of the DVMRP tunnel interface. Invalid
indicates an error in processing the configuration record.ro Enumeration .1.3.6.1.4.1.18.3.5.3.12.3.1.3 |
wfDvmrpTunnelCCTThe multicast circuit associated with this tunnel.ro INTEGER .1.3.6.1.4.1.18.3.5.3.12.3.1.4 |
wfDvmrpTunnelRemoteRouterIpAddress(unicast) IP address of remote network router neighbor.ro IpAddress .1.3.6.1.4.1.18.3.5.3.12.3.1.5 |
wfDvmrpTunnelEncapsModeWill these tunnelled datagrams be encapsulated within an IP datagram, or will
they be loosely encapsulated using the LSSR option (for the latter, refer to
RFC 1075; this is needed for backward compatibility)rw Enumeration .1.3.6.1.4.1.18.3.5.3.12.3.1.6 |
wfDvmrpTunnelMetricCost of using this tunnelrw INTEGER .1.3.6.1.4.1.18.3.5.3.12.3.1.7 |
wfDvmrpTunnelThresholdThreshold for forwarding through this tunnel; if TTL < threshold, the
datagram is dropped.rw INTEGER .1.3.6.1.4.1.18.3.5.3.12.3.1.8 |
wfDvmrpTunnelInPktsNumber of datagrams received on this interfacero Counter .1.3.6.1.4.1.18.3.5.3.12.3.1.9 |
wfDvmrpTunnelOutPktsNumber of datagrams send on this interfacero Counter .1.3.6.1.4.1.18.3.5.3.12.3.1.10 |
wfDvmrpTunnelInRouteUpdatesNumber of DVMRP route update messages receivedro Counter .1.3.6.1.4.1.18.3.5.3.12.3.1.11 |
wfDvmrpTunnelOutRouteUpdatesNumber of DVMRP route update messages sentro Counter .1.3.6.1.4.1.18.3.5.3.12.3.1.12 |
wfDvmrpTunnelInPktDiscardsNumber of inbound datagrams discarded due to route not found or due to
invalid inner address (dest address != multicast)ro Counter .1.3.6.1.4.1.18.3.5.3.12.3.1.13 |
wfDvmrpTunnelOutPktDiscardsNumber of outbound datagrams discarded due to route not foundro Counter .1.3.6.1.4.1.18.3.5.3.12.3.1.14 |
wfDvmrpTunnelLocalRouterIpAddress(unicast) IP address of local network router. To support multinet.ro IpAddress .1.3.6.1.4.1.18.3.5.3.12.3.1.15 |
wfDvmrpTunnelFwdCacheSizeMaximum number of entries allowed in the Forwarding table
at one time. there is a Forwarding table per vifrw INTEGER .1.3.6.1.4.1.18.3.5.3.12.3.1.16 |
wfDvmrpTunnelFwdCacheTTLThe time_to_live for the Forwarding table entries in seconds .rw INTEGER .1.3.6.1.4.1.18.3.5.3.12.3.1.17 |
wfDvmrpTunnelFwdCacheEntriesThe most up to date number of entries in the forwarding cachero INTEGER .1.3.6.1.4.1.18.3.5.3.12.3.1.18 |
wfDvmrpTunnelInPrunePktsNumber of PRUNE datagrams received on this interfacero Counter .1.3.6.1.4.1.18.3.5.3.12.3.1.19 |
wfDvmrpTunnelOutPrunePktsNumber of PRUNE datagrams send on this interfacero Counter .1.3.6.1.4.1.18.3.5.3.12.3.1.20 |
wfDvmrpTunnelInGraftPktsNumber of GRAFT datagrams received on this interfacero Counter .1.3.6.1.4.1.18.3.5.3.12.3.1.21 |
wfDvmrpTunnelOutGraftPktsNumber of GRAFT datagrams send on this interfacero Counter .1.3.6.1.4.1.18.3.5.3.12.3.1.22 |
wfDvmrpTunnelInGraftAckPktsNumber of GRAFT_ACK datagrams received on this interfacero Counter .1.3.6.1.4.1.18.3.5.3.12.3.1.23 |
wfDvmrpTunnelOutGraftAckPktsNumber of GRAFT_ACK datagrams send on this interfacero Counter .1.3.6.1.4.1.18.3.5.3.12.3.1.24 |
wfDvmrpTunnelDefaultRouteSupplySend the default route, 0.0.0.0 on this interfacerw Enumeration .1.3.6.1.4.1.18.3.5.3.12.3.1.25 |
wfDvmrpTunnelDefaultRouteListenReceive the default route, 0.0.0.0 on this interfacerw Enumeration .1.3.6.1.4.1.18.3.5.3.12.3.1.26 |
wfDvmrpTunnelCtrlMsgModeDvmrp tunneling control messages encapsulated type.
noencaps is the mode that control messages are sent in regular
igmp packets with ip protocol type set to IP_PROTOCOL_IGMP.
encaps is the mode that control messages are encapsed inside
ip packets with ip protocol type set to IP_PROTOCOL_IPINIP.
All DVMRP messages sent across tunnels will be encapsulated
in the same way as data packets in this mode.rw Enumeration .1.3.6.1.4.1.18.3.5.3.12.3.1.27 |
wfDvmrpTunnelReportDependProbeThis is to control accepting the route report. According to
the protocol, dvmrp should send probe packet before sending
the route report packet to the neighbors. But some vendor
implementations do not send probes before sending reports.
Enable: only process the routes from the neighbor sending
probes. Disable: No Dependency (no restriction).rw Enumeration .1.3.6.1.4.1.18.3.5.3.12.3.1.28 |
wfDvmrpTunnelPruneLifeTimeThe life time of the prune message the router send
to its neighbor in seconds.rw INTEGER .1.3.6.1.4.1.18.3.5.3.12.3.1.29 |
wfDvmrpTunnelAcceptAggregateRoutesCount of number of routes received have been
aggregated to the specific aggregate route currently
in route table for this interface.ro INTEGER .1.3.6.1.4.1.18.3.5.3.12.3.1.30 |
wfDvmrpTunnelAnnounceAggregatedRoutesCount of number of routes have been aggregated to
the specific aggregate route for advertisement currently
in route table for this interface.ro INTEGER .1.3.6.1.4.1.18.3.5.3.12.3.1.31 |
wfDvmrpRouteEntryTableMIB proxy: main DVMRP routing table SEQUENCE OF WfDvmrpRouteEntry .1.3.6.1.4.1.18.3.5.3.12.4 |
wfDvmrpRouteEntrySupported by mib proxy. One entry exists for each active route. WfDvmrpRouteEntry .1.3.6.1.4.1.18.3.5.3.12.4.1 |
wfDvmrpRouteSourceNetworkA source of multicast datagramsro IpAddress .1.3.6.1.4.1.18.3.5.3.12.4.1.1 |
wfDvmrpRouteSourceMaskMask for the specified source networkro IpAddress .1.3.6.1.4.1.18.3.5.3.12.4.1.2 |
wfDvmrpRouteNextHopRouterNext hop multicast router to the specified source
network; we consider this neighboring router to be on the
shortest path to the source. Note that this neighboring router
may be a tunnel endpoint.ro IpAddress .1.3.6.1.4.1.18.3.5.3.12.4.1.3 |
wfDvmrpRouteNextHopInterfaceCCTNext hop interface (CCT) to the specified source router; we
consider this interface to be on the shortest path to the source.ro INTEGER .1.3.6.1.4.1.18.3.5.3.12.4.1.4 |
wfDvmrpRouteNextHopInterfaceTunnelIdNext hop interface (tunnel id) to the specified source router; we
consider this interface to be on the shortest path to the source.ro IpAddress .1.3.6.1.4.1.18.3.5.3.12.4.1.5 |
wfDvmrpRouteNextHopInterfaceLocalTunnelIdNext hop interface (local tunnel id) to the specified source router; we
consider this interface to be on the shortest path to the source.ro IpAddress .1.3.6.1.4.1.18.3.5.3.12.4.1.6 |
wfDvmrpRouteTimerroute timerro INTEGER .1.3.6.1.4.1.18.3.5.3.12.4.1.7 |
wfDvmrpRouteStateSet of flags indicating state of entry. Note that the
router uses this field as a bit mask.
0x8000 Network is local to this router
0x4000 Route is being timed
0x2000 Route is garbagedro INTEGER .1.3.6.1.4.1.18.3.5.3.12.4.1.8 |
wfDvmrpRouteMetriccurrent route metricro INTEGER .1.3.6.1.4.1.18.3.5.3.12.4.1.9 |
wfDvmrpRouteProtocolcurrent route protocol dvmrp (2) or mospf (4) or internal (6)
which is the route from unicast and incoming interface no i
dvmrp configure, if dvmrp is configured then the protocol will
be set to 2, see wfIgmpRoutingProtocolro INTEGER .1.3.6.1.4.1.18.3.5.3.12.4.1.10 |
wfDvmrpRouteTypeThe orginal route source from. If it is from
pure dvmrp route (0x0001)
unicast best route (0x0002)
unciast route but has dvmrp interface (0x0003)
ospf(0x0004)
ospf best route (0x0006)
ospf ase route (0x0008)ro INTEGER .1.3.6.1.4.1.18.3.5.3.12.4.1.11 |
wfDvmrpRouteAggregatedTypeRoute Aggregated types :
0 - normal route
1 - inbound aggregated route
2 - outbound aggregated route
4 - inbound aggregate route
8 - outbound aggregate routero INTEGER .1.3.6.1.4.1.18.3.5.3.12.4.1.12 |
wfDvmrpRouteInterfaceEntryTableMIB proxy: DVMRP VIF routing table SEQUENCE OF WfDvmrpRouteInterfaceEntry .1.3.6.1.4.1.18.3.5.3.12.5 |
wfDvmrpRouteInterfaceEntrySupported by mib proxy. One entry exists for each virtual interface on
an active route. It is associated with a route via the source network/
net mask fields. The instance ID includes tunnel ID, which is 0 for
non-tunnel interfaces. WfDvmrpRouteInterfaceEntry .1.3.6.1.4.1.18.3.5.3.12.5.1 |
wfDvmrpRouteInterfaceSourceNetworkA source of multicast datagramsro IpAddress .1.3.6.1.4.1.18.3.5.3.12.5.1.1 |
wfDvmrpRouteInterfaceSourceMaskMask for the specified source networkro IpAddress .1.3.6.1.4.1.18.3.5.3.12.5.1.2 |
wfDvmrpRouteInterfaceNextHopInterfaceCCTcircuit number with which this route is associatedro INTEGER .1.3.6.1.4.1.18.3.5.3.12.5.1.3 |
wfDvmrpRouteInterfaceNextHopInterfaceLocalTunnelIdTunnel ID for tunnelled interfaces. This value is zero
for non-tunnelled interfaces, otherwise it contains the local IP
address of the tunnel.ro IpAddress .1.3.6.1.4.1.18.3.5.3.12.5.1.4 |
wfDvmrpRouteInterfaceNextHopInterfaceTunnelIdTunnel ID for tunnelled interfaces. This value is zero
for non-tunnelled interfaces, otherwise it contains the remote IP
address of the tunnel.ro IpAddress .1.3.6.1.4.1.18.3.5.3.12.5.1.5 |
wfDvmrpRouteInterfaceStatestate of interface for this route. Note that the router
uses this field as a bit mask.
0x8000 - interface is leaf
0x4000 - interface is child
0x2000 - interface is in hold-down state
0x1000 - interface has loop neighbor for this routero INTEGER .1.3.6.1.4.1.18.3.5.3.12.5.1.6 |
wfDvmrpRouteInterfaceDominantRouterdominant router address for virtual interfacero IpAddress .1.3.6.1.4.1.18.3.5.3.12.5.1.7 |
wfDvmrpRouteInterfaceSubordinateRoutersubordinate router address for virtual interfacero IpAddress .1.3.6.1.4.1.18.3.5.3.12.5.1.8 |
wfDvmrpRouteInterfaceHoldDownTimerCurrent value of hold down timer, used to determine if
interface is for leaf or non-leaf network. Non-leaf network means
that a local network router considers us to be in the shortest
path to the source (they have sent us a route update with metric
>= infinity).ro INTEGER .1.3.6.1.4.1.18.3.5.3.12.5.1.9 |
wfDvmrpRouteInterfaceSPInDiscardsCount of inbound packets discarded because interface not on shortest pathroobsolete Counter .1.3.6.1.4.1.18.3.5.3.12.5.1.10 |
wfDvmrpRouteInterfaceSPOutDiscardsCount of outbound packets discarded because interface not on shortest pathroobsolete Counter .1.3.6.1.4.1.18.3.5.3.12.5.1.11 |
wfDvmrpRouteInterfaceThresholdOutDiscardsCount of outbound packets discarded because of thresholdroobsolete Counter .1.3.6.1.4.1.18.3.5.3.12.5.1.12 |
wfDvmrpRouteInterfaceInSuccessfulPktsCount of inbound packets accepted for forwardingroobsolete Counter .1.3.6.1.4.1.18.3.5.3.12.5.1.13 |
wfDvmrpRouteInterfaceOutSuccessfulPktsCount of outbound packets accepted for forwardingroobsolete Counter .1.3.6.1.4.1.18.3.5.3.12.5.1.14 |
wfDvmrpRouteInterfaceParentCCTcircuit number with which this route is associated;parent VIFro INTEGER .1.3.6.1.4.1.18.3.5.3.12.5.1.15 |
wfDvmrpRouteInterfaceParentLocalTunnelIdTunnel ID for tunnelled interfaces. This value is zero
for non-tunnelled interfaces, otherwise it contains the local IP
address of the tunnel; parent VIF.ro IpAddress .1.3.6.1.4.1.18.3.5.3.12.5.1.16 |
wfDvmrpRouteInterfaceParentTunnelIdTunnel ID for tunnelled interfaces. This value is zero
for non-tunnelled interfaces, otherwise it contains the remote IP
address of the tunnel; parent VIF.ro IpAddress .1.3.6.1.4.1.18.3.5.3.12.5.1.17 |
wfDvmrpNeighboringRouterEntryTableMIB proxy: DVMRP neighbor table SEQUENCE OF WfDvmrpNeighboringRouterEntry .1.3.6.1.4.1.18.3.5.3.12.6 |
wfDvmrpNeighboringRouterEntryThis entry is used to indentify the known neighboring routers for
a circuit. This object will be indentified by circuit number,
tunnel id (to identify local interface), and the IP address of the neighbor. WfDvmrpNeighboringRouterEntry .1.3.6.1.4.1.18.3.5.3.12.6.1 |
wfDvmrpNeighboringRouterCCTLocal circuit numberro INTEGER .1.3.6.1.4.1.18.3.5.3.12.6.1.1 |
wfDvmrpNeighboringRouterLocalTunnelIdTunnel Id for interface. This value is zero for non-
tunnelled interfaces, otherwise it contains the IP address of the
local tunnel endpoint.ro IpAddress .1.3.6.1.4.1.18.3.5.3.12.6.1.2 |
wfDvmrpNeighboringRouterTunnelIdTunnel Id for interface. This value is zero for non-
tunnelled interfaces, otherwise it contains the IP address of the
remote tunnel endpoint.ro IpAddress .1.3.6.1.4.1.18.3.5.3.12.6.1.3 |
wfDvmrpNeighboringRouterIpAddrIP address of neighboring routerro IpAddress .1.3.6.1.4.1.18.3.5.3.12.6.1.4 |
wfDvmrpNeighboringRouterStateState of neighbor. The router uses this as a bit mask.
0x8000 - Neighbor is being timedro INTEGER .1.3.6.1.4.1.18.3.5.3.12.6.1.5 |
wfDvmrpNeighboringRouterTimerCurrent value of neighbor timerro INTEGER .1.3.6.1.4.1.18.3.5.3.12.6.1.6 |
wfDvmrpNeighboringRouterGenIdThe neighboring router's generation identifier.ro INTEGER .1.3.6.1.4.1.18.3.5.3.12.6.1.7 |
wfDvmrpNeighboringRouterMajorVersionThe neighboring router's major DVMRP version number.ro INTEGER .1.3.6.1.4.1.18.3.5.3.12.6.1.8 |
wfDvmrpNeighboringRouterMinorVersionThe neighboring router's minor DVMRP version number.ro INTEGER .1.3.6.1.4.1.18.3.5.3.12.6.1.9 |
wfDvmrpNeighboringRouterCapabilitiesThis object describes the neighboring router's capabilities.
The leaf bit indicates that the neighbor has only one
interface with neighbors. The prune bit indicates that the
neighbor supports pruning. The generationID bit indicates
that the neighbor sends its generationID in Probe messages.
The mtrace bit indicates that the neighbor can handle
mtrace requests.ro INTEGER .1.3.6.1.4.1.18.3.5.3.12.6.1.10 |