Wellfleet-DECNET-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for Wellfleet-DECNET-MIB.
144
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
144 total| Object Name |
|---|
wfivRouteGroup OBJECT IDENTIFIER .1.3.6.1.4.1.18.3.5.2.1 |
RFC1155-SMI Unknown .1.3.6.1.4.1.18.3.5.2.1 |
wfivRouteCreateDelete'This value determines whether DECnet is configured on this slot.'rw Enumeration .1.3.6.1.4.1.18.3.5.2.1.1 |
wfivRouteEnableDisable'This value determines whether DECnet is to startup.'rw Enumeration .1.3.6.1.4.1.18.3.5.2.1.2 |
wfivRouteState'This value determines whether DECnet is to startup.'ro Enumeration .1.3.6.1.4.1.18.3.5.2.1.3 |
wfivRouteBroadcastRouteTimer'This value determines the maximum time allowed between
Routing updates on Ethernet circuits. When this timer expires
before a routing update occurs, a routing update is forced.
With a standard calculation, Routing also uses this timer to
enforce a minimum delay between routing updates. Seconds is a
decimal integer in the range 1-65535.'rw INTEGER .1.3.6.1.4.1.18.3.5.2.1.4 |
wfivRouteRoutingVers'This read-only parameter identifies the executor node's
Routing version number. The format is the same as for the
Network Management version number.'ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.18.3.5.2.1.5 |
wfivRouteMaxAddr'This value represents the largest node number and,
therefore, number of nodes that can be known about
by the executor node's home area. The number is an integer
in the range 1-1023.'rw INTEGER .1.3.6.1.4.1.18.3.5.2.1.6 |
wfivRouteMaxBdcastNonRouters'This value represents the maximum total number of nonrouters
the executor node can have on its broadcast circuits for one slot.
The number is an integer in the range 0-1023.'rw INTEGER .1.3.6.1.4.1.18.3.5.2.1.7 |
wfivRouteMaxBdcastRouters'This value represents the maximum total number of routers the
executor node can have on its broadcast circuits for one slot.
The number is an integer in the range 0-1023.'rw INTEGER .1.3.6.1.4.1.18.3.5.2.1.8 |
wfivRouteMaxCircuits'This value represents the maximum number of Routing circuits
that the executor node can know about. The number is decimal
in the range 1-65535. Wellfleet limits this to 1024'rw INTEGER .1.3.6.1.4.1.18.3.5.2.1.9 |
wfivRouteMaxCost'This value represents the maximum total path cost allowed
from the executor to any node within an area. The path cost is
the sum of the circuit costs along a path between two nodes.
This parameter defines the point where the executor node's
Routing decision algorithm declares another node
unreachable because the cost of the least costly path to the
other node is excessive. For correct operation, this parameter
must not be less than the maximum path cost of the network.
The MAXIMUM COST number is decimal in the range
1-1022.'rw INTEGER .1.3.6.1.4.1.18.3.5.2.1.10 |
wfivRouteMaxHops'This value represents the maximum number of routing hops
allowable from the executor to any other reachable node within
an area. (A hop is the logical distance over a circuit between
two adjacent nodes.) This parameter defines the point where
the executor node's Routing decision algorithm
declares another node unreachable because the length of the
shortest path between the two nodes is too long. For correct
operation, this parameter must not be less than the network
diameter. (The network diameter is the reachability distance
between the two nodes of the network having the greatest
reachability distance, where reachability distance is the
length the shortest path between a given pair of nodes.) The
MAXIMUM HOPS number is decimal in the range 1-30.'rw INTEGER .1.3.6.1.4.1.18.3.5.2.1.11 |
wfivRouteMaxVisits'This value represents the maximum number of nodes a message
coming into the executor node can have visited. If the message
is not for this node and the MAXIMUM VISITS number is exceeded,
the message is discarded. The MAXIMUM VISITS parameter defines
the point where the packet lifetime control algorithm discards
a packet that has traversed too many nodes. For correct
operation, this parameter must not be less than the maximum
path length of the network. (The maximum path length is the
routing distance between the two nodes of the network having
the greatest routing distance, where routing distance is the
length of the least costly path between a given pair of nodes.)
The MAXIMUM VISITS number is decimal in the range MAXIMUM HOPS
to 63.'rw INTEGER .1.3.6.1.4.1.18.3.5.2.1.12 |
wfivRouteAreaMaxCost'This value represents the maximum total path cost allowed
from the executor to any other level 2 routing node. The AREA
MAXIMUM COST number is decimal in the range
1-1022. This parameter is only applicable if the executor
node is of type AREA.'rw INTEGER .1.3.6.1.4.1.18.3.5.2.1.13 |
wfivRouteAreaMaxHops'This value represents the maximum number of routing hops
allowable from the executor to any other level 2 routing node.
The AREA MAXIMUM HOPS number is decimal in the range
1-30.This parameter is only applicable if the executor node
is of type AREA.'rw INTEGER .1.3.6.1.4.1.18.3.5.2.1.14 |
wfivRouteMaxArea'This value represents the largest area number and, therefore,
number of areas that can be known about by the executor node's
Routing. This parameter is only applicable if the executor
node is of type AREA. The number is an integer in the range
1-63.'rw INTEGER .1.3.6.1.4.1.18.3.5.2.1.15 |
wfivRouteType'This parameter indicates the type of the executor node. The
node-type is one of the following:
ROUTING III
NONROUTING III
ROUTING IV
NONROUTING IV
AREA
A routing node has full routing capability. A nonrouting node
contains a subset of the Routing modules. The III and
IV indicate the DNA phase of the node. Nonrouting nodes can
deliver and receive packets to and from any node, but cannot
route packets from other nodes through to other nodes. An
area node routes between areas. Refer to the Routing
specification for details.
For adjacent nodes, this is a read-only parameter that
indicates the type of the reachable adjacent node.
NOTE: The ROUTING III and NONROUTING III values are
incremented by one compared to the standard DECnet values in
order to maintain compliance with RFC 1155)'rw Enumeration .1.3.6.1.4.1.18.3.5.2.1.16 |
wfivRouteNumAdjsThis value represents the total number of adjacencies learned by
the router.ro Counter .1.3.6.1.4.1.18.3.5.2.1.17 |
wfivRouteNumLvl1RtsThis value represents the total number of Level 1 Routes learned by
the router.ro Counter .1.3.6.1.4.1.18.3.5.2.1.18 |
wfivRouteNumAreasThis value represents the total number of Areas learned by
the router.ro Counter .1.3.6.1.4.1.18.3.5.2.1.19 |
wfivRouteLevel1AreaDECnet Phase IV area number for all circuits if this is a
LEVEL 1 ONLY router. Put here for site manager convenience.rw INTEGER .1.3.6.1.4.1.18.3.5.2.1.20 |
wfivTriggeredUpdatesThis will turn triggered updates on or off, Undernormal
conditions this should always be on.rw Enumeration .1.3.6.1.4.1.18.3.5.2.1.21 |
wfivTriggeredIntervalThis is the time interval between triggered updates, this
should always be 1 (second) unless you are told by Nortel
to set this differently.rw INTEGER .1.3.6.1.4.1.18.3.5.2.1.22 |
wfivCircuitTable' Table of DECnet Circuit Configuration and Counter Records' SEQUENCE OF WfivCircuitEntry .1.3.6.1.4.1.18.3.5.2.2 |
wfivCircuitEntry'Parameters information about all circuits currently known.
NOTE: depending on the type of object being querried (e.g., a
level 1 vs. a level 2 router or end system) some variables may
not be present.' WfivCircuitEntry .1.3.6.1.4.1.18.3.5.2.2.1 |
wfivCircuitCreateDelete'This value determines whether the circuit is configured'rw Enumeration .1.3.6.1.4.1.18.3.5.2.2.1.1 |
wfivCircuitEnableDisable'This value represents the circuit's Network Management
operational state. NOTE: These values are incremented by one
compared to the standard DECnet values in order to maintain
compliance with RFC 1155.'rw Enumeration .1.3.6.1.4.1.18.3.5.2.2.1.2 |
wfivCircuitCommonState'This value represents the circuit's operational state.'ro Enumeration .1.3.6.1.4.1.18.3.5.2.2.1.3 |
wfivCircuitArea'DECnet Phase IV area number for this circuit.'rw INTEGER .1.3.6.1.4.1.18.3.5.2.2.1.4 |
wfivCircuitNodeid'DECnet Phase IV node address for this circuit.'rw INTEGER .1.3.6.1.4.1.18.3.5.2.2.1.5 |
wfivCircuitNodeAddr'The address of the adjacent node.'ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.18.3.5.2.2.1.6 |
wfivCircuitID'A unique value for each known circuit.'ro INTEGER .1.3.6.1.4.1.18.3.5.2.2.1.7 |
wfivCircuitCommonType'Represents the type of the circuit. For X.25 circuits, the
value must be set to X25. For DDCMP and Ethernet circuits it
is read only and is the same value as the protocol of
the associated line.
NOTE: Values 1 - 5 are incremented by one compared to the
standard DECnet values in order to maintain compliance with
RFC 1155.'ro Enumeration .1.3.6.1.4.1.18.3.5.2.2.1.8 |
wfivCircuitExecCost'This value represents the Routing cost of the circuit.
Routing routes messages along the path between two nodes having
the smallest cost. The cost is a decimal integer in the range
1-63.'rw INTEGER .1.3.6.1.4.1.18.3.5.2.2.1.9 |
wfivCircuitExecHelloTimer'This value determines the frequency of Routing Hello (T3) messages
sent to the adjacent node on the circuit. Seconds is a decimal
integer in the range 1-8191.'rw INTEGER .1.3.6.1.4.1.18.3.5.2.2.1.10 |
wfivCircuitDesigRouterNodeAddr'This value is the address of the designated router.'ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.18.3.5.2.2.1.11 |
wfivCircuitMaxRouters'NR -This parameter is the maximum number of routers (including
the executor itself) allowed on the circuit by Routing for
circuits that are owned by the executor node. Number is a
decimal integer in the range 1-33.'rw INTEGER .1.3.6.1.4.1.18.3.5.2.2.1.12 |
wfivCircuitRouterPri'This parameter is the priority that this router is to have in
the selection of designated router for the circuit on circuits
that are owned by the executor node. Number is a decimal
integer in the range 0-127. The default value is 64.'rw INTEGER .1.3.6.1.4.1.18.3.5.2.2.1.13 |
wfivCircuitCountAgedPktLoss'Aged packet loss.'ro Counter .1.3.6.1.4.1.18.3.5.2.2.1.14 |
wfivCircuitCountNodeUnrPktLoss'Node unreachable packet loss.'ro Counter .1.3.6.1.4.1.18.3.5.2.2.1.15 |
wfivCircuitCountOutRngePktLoss'Node out-of-range packet loss.'ro Counter .1.3.6.1.4.1.18.3.5.2.2.1.16 |
wfivCircuitCountOverSzePktLoss'Oversized packet loss.'ro Counter .1.3.6.1.4.1.18.3.5.2.2.1.17 |
wfivCircuitCountPacketFmtErr'Packet format errors.'ro Counter .1.3.6.1.4.1.18.3.5.2.2.1.18 |
wfivCircuitCountPtlRteUpdtLoss'Partial routing update loss.'ro Counter .1.3.6.1.4.1.18.3.5.2.2.1.19 |
wfivCircuitCountTransitPksRecd'Transit packets Received. This value is stored internally as
a 32 bit value.'ro Counter .1.3.6.1.4.1.18.3.5.2.2.1.20 |
wfivCircuitCountTransitPkSent'Transit packets sent. This value is stored internally as
a 32 bit value.'ro Counter .1.3.6.1.4.1.18.3.5.2.2.1.21 |
wfivCircuitCountRtHelloSent' Router Hellos Sent'ro Counter .1.3.6.1.4.1.18.3.5.2.2.1.22 |
wfivCircuitCountRtHelloRcvd' Router Hellos Received'ro Counter .1.3.6.1.4.1.18.3.5.2.2.1.23 |
wfivCircuitCountHelloSent' Endnode Hellos Sent'ro Counter .1.3.6.1.4.1.18.3.5.2.2.1.24 |
wfivCircuitCountHelloRcvd' Endnode Hellos Received'ro Counter .1.3.6.1.4.1.18.3.5.2.2.1.25 |
wfivCircuitCountL1UpdSent' Level 1 Routing Updates Sent'ro Counter .1.3.6.1.4.1.18.3.5.2.2.1.26 |
wfivCircuitCountL1UpdRcvd' Level 1 Routing Updates Received'ro Counter .1.3.6.1.4.1.18.3.5.2.2.1.27 |
wfivCircuitCountAreaUpdSent' Area Routing Updates Sent'ro Counter .1.3.6.1.4.1.18.3.5.2.2.1.28 |
wfivCircuitCountAreaUpdRcvd' Area Routing Updates Received'ro Counter .1.3.6.1.4.1.18.3.5.2.2.1.29 |
wfivCircuitCountDropped' Dropped Packets 'ro Counter .1.3.6.1.4.1.18.3.5.2.2.1.30 |
wfivCircuitAllEndnodesMac'This parameter can be used to assign the AllEndnodes multicast
MAC address value for use over WAN media (e.g. Frame Relay).'rw OCTET STRING .1.3.6.1.4.1.18.3.5.2.2.1.31 |
wfivCircuitAllRoutersMac'This parameter can be used to assign the AllRouters multicast
MAC address value for use over WAN media (e.g. Frame Relay).'rw OCTET STRING .1.3.6.1.4.1.18.3.5.2.2.1.32 |
wfivCircuitAllAreaRoutersMac'This parameter can be used to assign the AllAreaRouters multicast
MAC address value for use over WAN media (e.g. Frame Relay).'rw OCTET STRING .1.3.6.1.4.1.18.3.5.2.2.1.33 |
wfivCircuitHelloEnableDisable' This parameter is used to disable to sending of Hellos
to Endnodes. It would be used in conjunction with Static
Adjacencies to limit the amount of data passed over a WAN
link (e.g. Frame Relay).'rw Enumeration .1.3.6.1.4.1.18.3.5.2.2.1.34 |
wfivCircuitRtHelloEnableDisable' This parameter is used to disable to sending of Hellos
to Routers. It would be used in conjunction with Static
Adjacencies to limit the amount of data passed over a WAN
link (e.g. Frame Relay).'rw Enumeration .1.3.6.1.4.1.18.3.5.2.2.1.35 |
wfivCircuitL1UpdateEnableDisable' This parameter is used to disable to sending of Level 1
topology updates. It would be used in conjunction with Static
Adjacencies to limit the amount of data passed over a WAN
link (e.g. Frame Relay).'rw Enumeration .1.3.6.1.4.1.18.3.5.2.2.1.36 |
wfivCircuitAllEndnodesMacInUse'This parameter displays the AllEndnodes multicast
MAC address value in use over WAN media (e.g. Frame Relay).'ro OCTET STRING .1.3.6.1.4.1.18.3.5.2.2.1.37 |
wfivCircuitAllRoutersMacInUse'This parameter displays the AllRouters multicast
MAC address value in use over WAN media (e.g. Frame Relay).'ro OCTET STRING .1.3.6.1.4.1.18.3.5.2.2.1.38 |
wfivCircuitAllAreaRoutersMacInUse'This parameter displays the AllAreaRouters multicast
MAC address value for use over WAN media (e.g. Frame Relay).'ro OCTET STRING .1.3.6.1.4.1.18.3.5.2.2.1.39 |
wfivCircuitL2UpdateDisable' This parameter is used to disable to sending of Level 2
topology updates. It would be used in conjunction with Static
Adjacencies and Static Routes to limit the amount of data passed
over a WANl link (e.g. Frame Relay).'rw Enumeration .1.3.6.1.4.1.18.3.5.2.2.1.40 |
wfivCircuitLevel' This parameter is used to indicate at the circuit level
whether the routing is LEVEL 1 only, or LEVEL 1 and LEVEL 2
routing.'rw Enumeration .1.3.6.1.4.1.18.3.5.2.2.1.41 |
wfivLevel1RouteTable' Table of Level 1 Routing Table Entries' SEQUENCE OF WfivLevel1RouteEntry .1.3.6.1.4.1.18.3.5.2.3 |
wfivLevel1RouteEntry'A Record in the Level 1 Routing Table' WfivLevel1RouteEntry .1.3.6.1.4.1.18.3.5.2.3.1 |
wfivLevel1AreaId'Area Id for this node'ro INTEGER .1.3.6.1.4.1.18.3.5.2.3.1.1 |
wfivLevel1NodeId'Node Id for this node'ro INTEGER .1.3.6.1.4.1.18.3.5.2.3.1.2 |
wfivLevel1RouteNodeAddr'This value is the address of the node about which routing
information is contained in this level 1 routing table.'ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.18.3.5.2.3.1.3 |
wfivLevel1RouteCircuitID'This READ_ONLY parameter identifies the circuit used to get
to a remote node. Circuit-id is an id-string. This parameter
can be used when displaying a list of nodes to indicate that
the display is to be restricted to those nodes adjacent on the
specified circuit.'ro INTEGER .1.3.6.1.4.1.18.3.5.2.3.1.4 |
wfivLevel1RouteCost'This READ_ONLY parameter represents the total cost over the
current path to the destination node. Cost is a positive
integer value associated with using a circuit. Routing routes
messages (data) along the path between two nodes with the
smallest cost. COST is kept on a remote node basis.'ro INTEGER .1.3.6.1.4.1.18.3.5.2.3.1.5 |
wfivLevel1RouteHops'This READ_ONLY parameter represents the number of hops over
to a destination node. A hop is Routing value representing
the logical distance between two nodes in a network. HOPS is
kept on a remote node basis.'ro INTEGER .1.3.6.1.4.1.18.3.5.2.3.1.6 |
wfivLevel1RouteNextNode'This READ_ONLY value indicates the next node on the circuit
used to get to the node under scrutiny (next hop).'ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.18.3.5.2.3.1.7 |
wfivLevel1RouteDynamicThis READ_WRITE parameter will indicate the type of Level 1 route,
whether it is a Dynamic or a Static routerw Enumeration .1.3.6.1.4.1.18.3.5.2.3.1.8 |
wfivAreaTable'Table of Area Routing Table Entries' SEQUENCE OF WfivAreaEntry .1.3.6.1.4.1.18.3.5.2.4 |
wfivAreaEntry'The area routing information.' WfivAreaEntry .1.3.6.1.4.1.18.3.5.2.4.1 |
wfivAreaNum'This value indicates the area number of this entry.'ro INTEGER .1.3.6.1.4.1.18.3.5.2.4.1.1 |
wfivAreaState'This value indicates the state of the area'ro Enumeration .1.3.6.1.4.1.18.3.5.2.4.1.2 |
wfivAreaCost'The total cost over the current path to the
destination area. Cost is a value associated with
using a circuit. Routing routes messages (data)
along the path between 2 areas with the smallest
cost.'ro INTEGER .1.3.6.1.4.1.18.3.5.2.4.1.3 |
wfivAreaHops'The number of hops to a destination area. A hop is
the routing value representing the logical distance
between two areas in network.'ro INTEGER .1.3.6.1.4.1.18.3.5.2.4.1.4 |
wfivAreaCircuitID'The circuit used to get to the remote area'ro INTEGER .1.3.6.1.4.1.18.3.5.2.4.1.5 |
wfivAreaNextNode'The next node on the circuit used to get to the
area under scrutiny.'ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.18.3.5.2.4.1.6 |
wfivAreaRouteDynamicThis READ_WRITE parameter will indicate the type of Level 2 route,
whether it is a Dynamic or a Static routerw Enumeration .1.3.6.1.4.1.18.3.5.2.4.1.7 |
wfivAdjTableAdjacency Table SEQUENCE OF WfivAdjEntry .1.3.6.1.4.1.18.3.5.2.5 |
wfivAdjEntry' Adjacency Table - the real index is the adjacency index' WfivAdjEntry .1.3.6.1.4.1.18.3.5.2.5.1 |
wfivAdjIndex'Index in the Adjacency Table'ro INTEGER .1.3.6.1.4.1.18.3.5.2.5.1.1 |
wfivAdjNodeAddr'The address of the adjacent node.'ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.18.3.5.2.5.1.2 |
wfivAdjBlockSize'This READ_ONLY parameter is the block size that was
negotiated with the adjacent Routing layer during Routing
initialization over a particular circuit. It includes the
routing header, but excludes the data link header. This
parameter is qualified by ADJACENT NODE.'ro INTEGER .1.3.6.1.4.1.18.3.5.2.5.1.3 |
wfivAdjListenTimer'This READ_ONLY value determines the maximum time allowed to
elapse before Routing receives some message (either a Hello
message or a user message) from the adjacent node on the
circuit. It was agreed during Routing initialization with the
adjacent Routing layer. Seconds is a decimal integer in the
range 1-65535. This parameter is qualified by ADJACENT NODE.'ro INTEGER .1.3.6.1.4.1.18.3.5.2.5.1.4 |
wfivAdjCircuitID'A unique value for each known circuit.'ro INTEGER .1.3.6.1.4.1.18.3.5.2.5.1.5 |
wfivAdjType'This parameter indicates the type of adjacency.
For adjacent nodes, this is a READ_ONLY parameter that
indicates the type of the reachable adjacent node.
NOTE: The ROUTING III and NONROUTING III values are
incremented by one compared to the standard DECnet values in
order to maintain compliance with RFC 1155)
ROUTING III (1),
NONROUTING III (2),
AREA (3),
ROUTING IV (4),
NONROUTING IV (5)'ro INTEGER .1.3.6.1.4.1.18.3.5.2.5.1.6 |
wfivAdjState'This value indicates the state of a router adjacency.
On adjacencies over a circuit of type (wfivCircuitCommonType)
Ethernet, CI, or FDDI, with an adjacent node of type
(wfivAdjType) ROUTING IV or AREA, this variable is the state
of the Ethernet Initialization Layer for this adjacency, and
can have values INITIALIZING or UP. (See Section 9.1.1 of
DECnet Phase IV Routing Layer Functional Specification.)
On adjacencies over a circuit of type (wfivCircuitCommonType)
Ethernet, CI, or FDDI, with an adjacent node of type
(wfivAdjType) NONROUTING IV, this varaible will always take on
the value UP.
On adjacencies over a circuit of type (wfivCircuitCommonType)
DDCMP POINT, DDCMP CONTROL, DDCMP TRIBUTARY, DDCMP DMC, or
X.25, this variable is the state of the Routing Layer
Initialization Circuit State. (See section 7.3, ibid.) It can
have values between RUN and HALT.
On adjacencies over a circuit of type (wfivCircuitCommonType)
OTHER, this variable may be used in a manner consistent with
the Initialization Layer used on that circuit.
INITIALIZING (1),
UP (2),
RUN (3),
CIRCUIT REJECTED (4),
DATA LINK START (5),
ROUTING LAYER INITIALIZE (6),
ROUTING LAYER VERIFY (7),
ROUTING LAYER COMPLETE (8),
OFF (9),
HALT (10)'ro Enumeration .1.3.6.1.4.1.18.3.5.2.5.1.7 |
wfivAdjPriority'Priority assigned by the adjacent node for this circuit.'ro INTEGER .1.3.6.1.4.1.18.3.5.2.5.1.8 |
wfivAdjClass'Specifies whether this adjacency is Static or Dynamic'ro INTEGER .1.3.6.1.4.1.18.3.5.2.5.1.9 |
wfivTrafficFilterTableDECNET Traffic Filters SEQUENCE OF WfivTrafficFilterEntry .1.3.6.1.4.1.18.3.5.2.6 |
wfivTrafficFilterEntryAn entry in WfivTrafficFilterTable. WfivTrafficFilterEntry .1.3.6.1.4.1.18.3.5.2.6.1 |
wfivTrafficFilterCreateDefines the existence of the traffic filter rule:
created - traffic filter exists
delete - traffic filter does not exist and can be deleted.rw Enumeration .1.3.6.1.4.1.18.3.5.2.6.1.1 |
wfivTrafficFilterEnableDefines whether or not the traffic filter rule should be used:
enabled - activate the rule.
disabled - inactivate the rule.rw Enumeration .1.3.6.1.4.1.18.3.5.2.6.1.2 |
wfivTrafficFilterStatusDefines the current status of the traffic filter:
inactive - the rule is not in use.
active - the rule is being used.
error - the application detected an error in the rule.ro Enumeration .1.3.6.1.4.1.18.3.5.2.6.1.3 |
wfivTrafficFilterCounterThe number of received packets that have
matched this rule.ro Counter .1.3.6.1.4.1.18.3.5.2.6.1.4 |
wfivTrafficFilterDefinitionThe filter rule definition.rw Opaque .1.3.6.1.4.1.18.3.5.2.6.1.5 |
wfivTrafficFilterReservedReserved field.ro INTEGER .1.3.6.1.4.1.18.3.5.2.6.1.6 |
wfivTrafficFilterCircuitThe ID of the Circuit to which the
filter is applied.ro INTEGER .1.3.6.1.4.1.18.3.5.2.6.1.7 |
wfivTrafficFilterRuleNumberID for the rule.ro INTEGER .1.3.6.1.4.1.18.3.5.2.6.1.8 |
wfivTrafficFilterFragmentFragment number - for large rules.ro INTEGER .1.3.6.1.4.1.18.3.5.2.6.1.9 |
wfivTrafficFilterNamename of the rule numberrw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.18.3.5.2.6.1.10 |
wfivStaticAdjTableStatic Adjacency Table SEQUENCE OF WfivStaticAdjEntry .1.3.6.1.4.1.18.3.5.2.7 |
wfivStaticAdjEntry' Static Adjacency Table ' WfivStaticAdjEntry .1.3.6.1.4.1.18.3.5.2.7.1 |
wfivStaticAdjCreateDelete'This value determines whether the static adjacency is configured'rw Enumeration .1.3.6.1.4.1.18.3.5.2.7.1.1 |
wfivStaticAdjEnableDisable'This value determines whether the static adjacency is active 'rw Enumeration .1.3.6.1.4.1.18.3.5.2.7.1.2 |
wfivStaticAdjArea'DECnet Phase IV area number for this static Adjacency.'ro INTEGER .1.3.6.1.4.1.18.3.5.2.7.1.3 |
wfivStaticAdjNodeid'DECnet Phase IV node address for this static adjacency.'ro INTEGER .1.3.6.1.4.1.18.3.5.2.7.1.4 |
wfivStaticAdjCircuitID'The circuit used for this static adjacency.'ro INTEGER .1.3.6.1.4.1.18.3.5.2.7.1.5 |
wfivStaticAdjNodeAddr'The address of the adjacent node in display format.'ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.18.3.5.2.7.1.6 |
wfivStaticAdjType' Specifies whether the static adjacency is to a router or end
station.'rw Enumeration .1.3.6.1.4.1.18.3.5.2.7.1.7 |
wfivStaticAdjPriority' Specifies the priority of the static adjacency if it's a
router.'rw INTEGER .1.3.6.1.4.1.18.3.5.2.7.1.8 |
wfivStaticAdjDestMACAddr' Specifies the destination MAC address of the Static Adjacency
if the circuit type is ATM, Frame Relay or SMDS.'rw OCTET STRING .1.3.6.1.4.1.18.3.5.2.7.1.9 |
wfivStaticRouteTableThis table contains the list of all static routes SEQUENCE OF WfivStaticRouteEntry .1.3.6.1.4.1.18.3.5.2.8 |
wfivStaticRouteEntryThis is the Static Route Entry for the Static Route Table WfivStaticRouteEntry .1.3.6.1.4.1.18.3.5.2.8.1 |
wfivStaticRouteDeleteCreate/Delete parameter for DECnet IV Static Route Recordrw Enumeration .1.3.6.1.4.1.18.3.5.2.8.1.1 |
wfivStaticRouteDisableEnable/Disable parameter for this Static Routerw Enumeration .1.3.6.1.4.1.18.3.5.2.8.1.2 |
wfivStaticRouteTypeThis parameter specifies whether this static route is for Level 1 or Level 2
type of routingrw Enumeration .1.3.6.1.4.1.18.3.5.2.8.1.3 |
wfivStaticRouteAreaIdThis specifies the area address of the static route. It is also a part of
the inst_idro INTEGER .1.3.6.1.4.1.18.3.5.2.8.1.4 |
wfivStaticRouteNodeIdThis specifies the node address of the static route. It is also a part of
the inst_idro INTEGER .1.3.6.1.4.1.18.3.5.2.8.1.5 |
wfivStaticRouteCostThis value is the cost to get to this addressrw INTEGER .1.3.6.1.4.1.18.3.5.2.8.1.6 |
wfivStaticRouteNextHopAreaIdThis is the area address of the next hop router that all data destined to
wfivStaticRouteAreaId will be forwarded toro INTEGER .1.3.6.1.4.1.18.3.5.2.8.1.7 |
wfivStaticRouteNextHopNodeIdThis is the node address of the next hop router that all data destined to
wfivStaticRouteAddr will be forwarded toro INTEGER .1.3.6.1.4.1.18.3.5.2.8.1.8 |
wfivDecnetTrans OBJECT IDENTIFIER .1.3.6.1.4.1.18.3.5.2.9 |
wfivDecnetTransPhase5PktsNumber of successfully translated Phase 5 (CLNP) packetsro Counter .1.3.6.1.4.1.18.3.5.2.9.1 |
wfivDecnetTransMtuFailNumber of times Phase 5 translation failed because the packet
was larger than the Phase 4 MTU size.ro Counter .1.3.6.1.4.1.18.3.5.2.9.2 |
wfivDecnetTransUnrFailNumber of times Phase 4 failed to find a route to the
destination.ro Counter .1.3.6.1.4.1.18.3.5.2.9.3 |
wfivDecnetTransNumPhase5EsNumber of Phase 5 ES Adjacencies announced by the Phase 5
(OSI) router.ro Counter .1.3.6.1.4.1.18.3.5.2.9.4 |
wfivAggrStats OBJECT IDENTIFIER .1.3.6.1.4.1.18.3.5.2.10 |
wfivAggrInPktsThe total number of packets received by the DECnet re-directorro Counter .1.3.6.1.4.1.18.3.5.2.10.1 |
wfivAggrOutPktsThe total number of packets sent by the DECnet re-directorro Counter .1.3.6.1.4.1.18.3.5.2.10.2 |
wfivAggrFormatErrsThe total number of packets received with format errorsro Counter .1.3.6.1.4.1.18.3.5.2.10.3 |
wfivAggrDestUnreachablesThe total number of packets received whose destinations
were unreachablero Counter .1.3.6.1.4.1.18.3.5.2.10.4 |
wfivAggrRangeErrsThe total number of packet received with nodes out of rangero Counter .1.3.6.1.4.1.18.3.5.2.10.5 |
wfivAggrOversizedPktsThe total number of oversized packets received.ro Counter .1.3.6.1.4.1.18.3.5.2.10.6 |
wfivAggrAgedPktsThe total number of packets aged outro Counter .1.3.6.1.4.1.18.3.5.2.10.7 |
wfivAggrFwdPktsThe total number of packets forwardedro Counter .1.3.6.1.4.1.18.3.5.2.10.8 |