Wellfleet-CSMACD-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for Wellfleet-CSMACD-MIB.
83
Objects
Active
Status
3
Dependencies
Imported Objects
Objects
83 total| Object Name |
|---|
RFC1155-SMICSMA/CD line record SEQUENCE OF WfCSMACDEntry .1.3.6.1.4.1.18.3.4.1 |
wfCSMACDEntryAn entry in the csmacd table WfCSMACDEntry .1.3.6.1.4.1.18.3.4.1.1 |
wfCSMACDDeletecreate/delete parameter, dflt = createdrw Enumeration .1.3.6.1.4.1.18.3.4.1.1.1 |
wfCSMACDEnableenable/disable parameter, dflt = enabledrw Enumeration .1.3.6.1.4.1.18.3.4.1.1.2 |
wfCSMACDStateline driver state variable, Not Present, Init, Down, Upro Enumeration .1.3.6.1.4.1.18.3.4.1.1.3 |
wfCSMACDSlotinstance ID Slot, filled in by driverro INTEGER .1.3.6.1.4.1.18.3.4.1.1.4 |
wfCSMACDConnectorinstance ID Connector, filled in by driver. For the ASN
this attribute is an encoded value and is equal to
'module'*10 + 'connector'. Where 'module' is defined in
attribute 42 and 'connector' is defined in attribute 43
of this table. For non-ASN platforms this attribute is
the physical connector number on the slot.ro INTEGER .1.3.6.1.4.1.18.3.4.1.1.5 |
wfCSMACDCctcct number for this line instancerw INTEGER .1.3.6.1.4.1.18.3.4.1.1.6 |
wfCSMACDBoflbofl parameter, dflt = enabledrw Enumeration .1.3.6.1.4.1.18.3.4.1.1.7 |
wfCSMACDBoflTmobofl parameter, dflt = 5. A value of zero has a special meaning.
When bofl tmo is zero, the line is killed as soon as the link down
down condition is determined.rw INTEGER .1.3.6.1.4.1.18.3.4.1.1.8 |
wfCSMACDMtumtu parameter, fixedro Enumeration .1.3.6.1.4.1.18.3.4.1.1.9 |
wfCSMACDMadrline MAC address, fixed - line driver fills inro OCTET STRING .1.3.6.1.4.1.18.3.4.1.1.10 |
wfCSMACDOctetsRxOkNumber of octets received without errorro Counter .1.3.6.1.4.1.18.3.4.1.1.11 |
wfCSMACDFramesRxOkNumber of frames received without errorro Counter .1.3.6.1.4.1.18.3.4.1.1.12 |
wfCSMACDOctetsTxOkNumber of octets transmitted without errorro Counter .1.3.6.1.4.1.18.3.4.1.1.13 |
wfCSMACDFramesTxOkNumber of frames transmitted without errorro Counter .1.3.6.1.4.1.18.3.4.1.1.14 |
wfCSMACDDeferredTxNumber of deferred transmissionsro Counter .1.3.6.1.4.1.18.3.4.1.1.15 |
wfCSMACDLateCollnTxNumber of late collisionsro Counter .1.3.6.1.4.1.18.3.4.1.1.16 |
wfCSMACDExcessvCollnTxNumber of excessive collisionsro Counter .1.3.6.1.4.1.18.3.4.1.1.17 |
wfCSMACDBablErrorTxNumber of frames transmitted larger than the MTU size
in wfCSMACDMturo Counter .1.3.6.1.4.1.18.3.4.1.1.18 |
wfCSMACDBufErrorTxNumber of internal buffer errorsro Counter .1.3.6.1.4.1.18.3.4.1.1.19 |
wfCSMACDLcarTxNumber of loss of carrier errorsro Counter .1.3.6.1.4.1.18.3.4.1.1.20 |
wfCSMACDUfloTxNumber of transmitter underflow errorsro Counter .1.3.6.1.4.1.18.3.4.1.1.21 |
wfCSMACDFcsErrorRxNumber of receiver checksum errorsro Counter .1.3.6.1.4.1.18.3.4.1.1.22 |
wfCSMACDAlignErrorRxNumber of receiver alignment errorsro Counter .1.3.6.1.4.1.18.3.4.1.1.23 |
wfCSMACDLackRescErrorRxNumber of receiver lack of resource errorsro Counter .1.3.6.1.4.1.18.3.4.1.1.24 |
wfCSMACDTooLongErrorRxNumber of frames received exceeding the MTU size
in wfCSMACDMtu.ro Counter .1.3.6.1.4.1.18.3.4.1.1.25 |
wfCSMACDOfloRxNumber of receiver overflow errorsro Counter .1.3.6.1.4.1.18.3.4.1.1.26 |
wfCSMACDMerrNumber of internal memory errorsro Counter .1.3.6.1.4.1.18.3.4.1.1.27 |
wfCSMACDCerrNumber of collision errorsro Counter .1.3.6.1.4.1.18.3.4.1.1.28 |
wfCSMACDHardwareFilterHardware filtering parameter.rw Enumeration .1.3.6.1.4.1.18.3.4.1.1.29 |
wfCSMACDTxQueueLengthCurrent Transmit Queue Lengthro INTEGER .1.3.6.1.4.1.18.3.4.1.1.30 |
wfCSMACDRxQueueLengthCurrent Receive Queue Lengthro INTEGER .1.3.6.1.4.1.18.3.4.1.1.31 |
wfCSMACDTxClipFramesNumber of frames clipped in driver's transmit routine due to transmit
congestion.ro Counter .1.3.6.1.4.1.18.3.4.1.1.32 |
wfCSMACDRxReplenMissesNumber of packet buffer misses while attempting to replenish driver
receive ring.ro Counter .1.3.6.1.4.1.18.3.4.1.1.33 |
wfCSMACDCfgTxQueueLengthConfigured Transmit Queue Length. Values other than zero over-ride
the router selected values. A value of zero has a special meaning.
Zero causes router based default values to be used. Values larger
than the compiled ring size are truncated to the compiled ring
size.rw INTEGER .1.3.6.1.4.1.18.3.4.1.1.34 |
wfCSMACDCfgRxQueueLengthConfigured Receive Queue Length. Values other than zero over-ride
the router selected values. A value of zero has a special meaning.
Zero causes router based default values to be used. Values larger
than the compiled ring size are truncated to the compiled ring
size.rw INTEGER .1.3.6.1.4.1.18.3.4.1.1.35 |
wfCSMACDAlignmentModeEnables special frame re-alignment in the Line Driver. Only needed when
4 ethernet interfaces are configured on a single slot. Only needed if
experiencing transmit underflow errors (wfCSMACDUfloTx). When this
attribute is set to DISABLED, non-optimally aligned frames are transmitted
as is. When this attribute is set to ALL (1), all non-optimally aligned
frames are re-aligned before transmission. When this attribute is set to
ALIGN_OVER_128_BYTES (2), all non-optimally aligned frames over 128 bytes
in length are re-aligned before transmission and frames up to and including
128 bytes in length are transmitted as is.rw Enumeration .1.3.6.1.4.1.18.3.4.1.1.36 |
wfCSMACDUnAlignedFramesNumber of non-optimally aligned frames queued to the driver for transmit.
This statistic does not indicate that any frames have been dropped. If
the ethernet I/O board is not a Quad Ethernet Link Module (QENET) or if it
is a QENET and none of the four ethernet interfaces are experiencing
transmit underflow errors (wfCSMACDUfloTx), then this statistic should be
ignored.
If, however, this interface or other interfaces on the QENET are
experiencing transmit underflow errors, the underflows are preventable
by setting the wfCSMACDAlignmentMode attribute to 1. See explanation of
that attribute for more information.
This attribute means that these frames are candidates for re-alignment.
It does not, by itself, indicate that re-alignment is necessary.ro Counter .1.3.6.1.4.1.18.3.4.1.1.37 |
wfCSMACDLineNumberLogical line number associated with this driver entity.rw INTEGER .1.3.6.1.4.1.18.3.4.1.1.38 |
wfCSMACDLateCollnRxNumber of late collisions - found in QUICC Ethernet Rx Buffer Descriptorsro Counter .1.3.6.1.4.1.18.3.4.1.1.39 |
wfCSMACDModuleModule number for ASN platform, filled in by driver. For non-ASN
platforms this attribute will not be used.ro Enumeration .1.3.6.1.4.1.18.3.4.1.1.40 |
wfCSMACDActualConnectorActual connector number for ASN platform, filled in by
driver. For non-ASN platforms this attribute will not be used.ro Enumeration .1.3.6.1.4.1.18.3.4.1.1.41 |
wfCSMACDLastChangeThe value of SysUpTime at the time the interface entered it's current
operational state (UP state). SysUpTime is defined as the time (in
hundredths of a second) since the network management portion of the
system was last re-initialized. Usually the time since boot.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.18.3.4.1.1.42 |
wfCSMACDOutQLenThe instantaneous current length of the output packet queue (in packets).ro Gauge .1.3.6.1.4.1.18.3.4.1.1.43 |
wfCSMACDIntProcessingscounts the number of times the interrupt service routine
has been calledro Counter .1.3.6.1.4.1.18.3.4.1.1.44 |
wfCSMACDTxProcessingsCounts the number of times the transmit routine
has been calledro Counter .1.3.6.1.4.1.18.3.4.1.1.45 |
wfCSMACDRxProcessingsCounts the number of times RINT processing takes place
in the interrupt service routine.ro Counter .1.3.6.1.4.1.18.3.4.1.1.46 |
wfCSMACDTxCmplProcessingsCounts the number of times the transmit complete
processing takes placero Counter .1.3.6.1.4.1.18.3.4.1.1.47 |
wfCSMACDTxQueueReductionsCounts the number of times the transmit queue
has been shrinked in size due to the number of
tx clips exceeding the tresholdro Counter .1.3.6.1.4.1.18.3.4.1.1.48 |
wfCSMACDSingleCollisionFramesA count of successfully transmitted frames on a particular interface
for which transmission is inhibited by exactly one collision.ro Counter .1.3.6.1.4.1.18.3.4.1.1.49 |
wfCSMACDMultipleCollisionFramesA count of successfully transmitted frames on a particular interface
for which transmission is inhibited by more than one collision.ro Counter .1.3.6.1.4.1.18.3.4.1.1.50 |
wfCSMACDInternalMacTxErrorsA count of frames for which transmission on a particular interface fails
due to an internal MAC sublayer transmit error. A frame is only counted
by an instance of this object if it is not counted by the corresponding
instance of either the LateCollisions object, the ExcessiveCollisions
object, or the CarrierSenseErrors object.ro Counter .1.3.6.1.4.1.18.3.4.1.1.51 |
wfCSMACDLineCapabilityIf NWay is configured, this attribute contains a value that uniquely
identifies the single capability that was agreed upon by the local and
remote interfaces. If NWay is not configured, this attribute describes
the speed and duplex setting that was configured for this interface.ro Enumeration .1.3.6.1.4.1.18.3.4.1.1.52 |
wfCSMACDEtherChipSetThis object contains an OBJECT IDENTIFIER which identifies the chipset used
to realize the interface. This object usually identifies the Medium Access
Control (MAC) chip.ro OBJECT IDENTIFIER .1.3.6.1.4.1.18.3.4.1.1.53 |
wfCSMACDRxSymbolErrorsA count of frames received on a particular interface with one or more
100Mb symbol errors detected.ro Counter .1.3.6.1.4.1.18.3.4.1.1.54 |
wfCSMACDInternalMacRxErrorsA count of frames for which reception on a particular interface fails
due to an internal MAC sublayer receive error. A frame is only counted
by an instance of this object if it is not counted by the corresponding
instance of either the FrameTooLongs object, the AlignmentErrors object,
or the FCSErrors object.ro Counter .1.3.6.1.4.1.18.3.4.1.1.55 |
wfCSMACDConfigurableSpeedThis attribute will be enabled(1) if the interface supports different
speed configurations. If configurable speeds are not supported on the
interface, this attribute will be disabled(2). Creation of
wfCSMACDAutoNegEntry records for 10/100BaseT is valid only if this
attribute is enabled. For Gigabit Ethernet the latter statement is not
truero Enumeration .1.3.6.1.4.1.18.3.4.1.1.56 |
wfCSMACDRxFlushesThis attribute describes the number of times the hardware
has entered a state which required a flush of the RX FIFO.ro Counter .1.3.6.1.4.1.18.3.4.1.1.57 |
wfCSMACDTxDeadlocksThis attribute describes the number of times the hardware
has entered a Tx Deadlock condition, and the software
intervenes to free up the lock.ro Counter .1.3.6.1.4.1.18.3.4.1.1.58 |
wfCSMACDBoflRetriesbofl retries, dflt = 5rw INTEGER .1.3.6.1.4.1.18.3.4.1.1.59 |
wfCSMACDBoflTmoDivisorbofl tmo divisorr, dflt = 1rw INTEGER .1.3.6.1.4.1.18.3.4.1.1.60 |
wfCSMACDTurboBoflDebugSpecial Turbo-BOFL debug mechanism to be used by Engineering
and Manufacturing only.
31-24 : TMO - period of breath (amount of time between
successive breaths of life)
23-16 : Number of packets per breath.
15-0 : Packet length in bytes - 22 bytes minimum.
All bits set to zero will disable this attribute.rw INTEGER .1.3.6.1.4.1.18.3.4.1.1.61 |
wfCSMACDIfIndexIfTable Index for this line instance,
filled in by driver. For the BAC it is not the same
as the circuit number.ro INTEGER .1.3.6.1.4.1.18.3.4.1.1.62 |
wfCSMACDTxFlowControlPauseFramesThis attribute indicates the number of Flow Control
Pause frames transmitted.ro Counter .1.3.6.1.4.1.18.3.4.1.1.63 |
wfCSMACDRxFlowControlPauseFramesThis attribute indicates the number of Flow Control
Pause frames received.ro Counter .1.3.6.1.4.1.18.3.4.1.1.64 |
wfCSMACDRxUnsupportedOpcodesThis attribute indicates the number of Control
frames received that were not pause frames.ro Counter .1.3.6.1.4.1.18.3.4.1.1.65 |
wfCSMACDFlowControlEnableFlow control enable/disable parameter, dflt = enabledrw Enumeration .1.3.6.1.4.1.18.3.4.1.1.66 |
wfCSMACDTxFlowControlPauseTimeThis attribute indicates flow control pause time in slots.rw INTEGER .1.3.6.1.4.1.18.3.4.1.1.67 |
wfCSMACDTxFlowControlPauseZeroEnableTx Pause 0 frame generation enable/disable parameter, dflt = enabled.rw Enumeration .1.3.6.1.4.1.18.3.4.1.1.68 |
wfCSMACDDsqmsLineSpeedUser-selected line speed for DSQMS clientrw INTEGER .1.3.6.1.4.1.18.3.4.1.1.69 |
wfCSMACDAutoNegTableCSMA/CD Auto Negotiation (NWay) record SEQUENCE OF WfCSMACDAutoNegEntry .1.3.6.1.4.1.18.3.4.16.1 |
wfCSMACDAutoNegEntryAn entry in the csmacd table WfCSMACDAutoNegEntry .1.3.6.1.4.1.18.3.4.16.1.1 |
wfCSMACDAutoNegDeletecreate/delete parameter, dflt = createdrw Enumeration .1.3.6.1.4.1.18.3.4.16.1.1.1 |
wfCSMACDAutoNegSlotinstance ID Slot, filled in by driverro INTEGER .1.3.6.1.4.1.18.3.4.16.1.1.2 |
wfCSMACDAutoNegConnectorinstance ID Connector, filled in by driver. For the ASN
this attribute is an encoded value and is equal to
'module'*10 + 'connector'. Where 'module' is defined in
attribute 42 and 'connector' is defined in attribute 43
of this table. For non-ASN platforms this attribute is
the physical connector number on the slot.ro INTEGER .1.3.6.1.4.1.18.3.4.16.1.1.3 |
wfCSMACDAutoNegSpeedSelectThis value indicates the configured speed of the local interface.
This parameter allows configuration of a specific speed and duplex
setting, or allows configuration/enabling of Auto Negotiation/NWay.
Selecting a specific speed (i.e. a value other than 1) implicitly
disables Auto Negotiation/NWay.rw Enumeration .1.3.6.1.4.1.18.3.4.16.1.1.4 |
wfCSMACDAutoNegRemoteSignalingThis value indicates whether the remote end of the link is operating
Auto Negotiation signaling or not. It shall take the value detected if,
during the previous link negotiation, FLP bursts were received from the
remote end.
NOTE: This parameter is only valid if SpeedSelect is configured for NWay.ro Enumeration .1.3.6.1.4.1.18.3.4.16.1.1.5 |
wfCSMACDAutoNegStateThis value indicates whether Auto Negotiation signaling is in progress
or has completed.
NOTE: This parameter is only valid if SpeedSelect is configured for NWay.ro Enumeration .1.3.6.1.4.1.18.3.4.16.1.1.6 |
wfCSMACDAutoNegRestartAutoConfigWriting any value to this attribute forces Auto Negotiation to begin link
re-negotiation. This action has no effect if Auto Negotiation signaling
is disabled.
NOTE: This parameter is only valid if SpeedSelect is configured for NWay.rw INTEGER .1.3.6.1.4.1.18.3.4.16.1.1.7 |
wfCSMACDAutoNegLocalCapabilityThis is a GAUGE because this attribute is 32-bit unsigned, non-increasing
A value that uniquely identifies the set of capabilities of the LOCAL Auto
Negotiation entity. The value is a sum which initially takes the value zero.
Then, for each capability of the LOCAL interface, 2 raised to the power
noted below is added to the sum. For example, a LOCAL interface which has
the capability to support only 100Base-TX would have a value of 128 (2**7).
In contrast, a LOCAL interface which supports both 100Base-TX and 100Base-TX
Full Duplex would cause this object to have a value of 384 ((2**7) + (2**8)).
The powers of 2 assigned to the capabilities are these:
Power Capability
0 Pause
1 ASM_DIR
5 10Base-T
6 10Base-T Full Duplex
7 100Base-TX
8 100Base-TX Full Duplex
9 100Base-T4
14 1000Base-X
15 1000Base-X Full Duplex
NOTE: This parameter is only valid if SpeedSelect is configured for NWay.ro Gauge .1.3.6.1.4.1.18.3.4.16.1.1.8 |
wfCSMACDAutoNegAdvertisedCapabilityThis is a GAUGE because this attribute is 32-bit unsigned, non-increasing
A successful set operation will result in immediate link re-negotiation if
AutoNegAdminState is enabled. A value that uniquely identifies the set of
capabilities advertised by the local Auto Negotiation entity. The value is
a sum which initially takes the value zero. Then, for each capability of
the ADVERTISED interface, 2 raised to the power noted below is added to the
sum. For example, a ADVERTISED interface which has the capability to support
only 100Base-TX would have a value of 128 (2**7). In contrast, an ADVERTISED
interface which supports both 100Base-TX and 100Base-TX Full Duplex would
cause this object to have a value of 384 ((2**7) + (2**8)).
The powers of 2 assigned to the capabilities are these:
Power Capability
0 Pause
1 ASM_DIR
5 10Base-T
6 10Base-T Full Duplex
7 100Base-TX
8 100Base-TX Full Duplex
9 100Base-T4
14 1000Base-X
15 1000Base-X Full Duplex
NOTE: This parameter is only valid if SpeedSelect is configured for NWay.rw Gauge .1.3.6.1.4.1.18.3.4.16.1.1.9 |
wfCSMACDAutoNegReceivedCapabilityThis is a GAUGE because this attribute is 32-bit unsigned, non-increasing
A value that uniquely identifies the set of capabilities of the REMOTE Auto
Negotiation entity. The value is a sum which initially takes the value zero.
Then, for each capability of the REMOTE interface, 2 raised to the power
noted below is added to the sum. For example, a REMOTE interface which has
the capability to support only 100Base-TX would have a value of 128 (2**7).
In contrast, a REMOTE interface which supports both 100Base-TX and 100Base-TX
Full Duplex would cause this object to have a value of 384 ((2**7) + (2**8)).
The powers of 2 assigned to the capabilities are these:
Power Capability
0 Pause
1 ASM_DIR
5 10Base-T
6 10Base-T Full Duplex
7 100Base-TX
8 100Base-TX Full Duplex
9 100Base-T4
14 1000Base-X
15 1000Base-X Full Duplex
NOTE: This parameter is only valid if SpeedSelect is configured for NWay.ro Gauge .1.3.6.1.4.1.18.3.4.16.1.1.10 |