Wellfleet-CCTOPTS-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for Wellfleet-CCTOPTS-MIB.
301
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
301 total| Object Name |
|---|
RFC1155-SMIThe table of circuit names SEQUENCE OF WfCctOptsEntry .1.3.6.1.4.1.18.3.5.1.4.1 |
wfCctOptsEntryEntry format for the table of circuit options WfCctOptsEntry .1.3.6.1.4.1.18.3.5.1.4.1.1 |
wfCctOptsDeleteCreation and deletion flag for this recordrw Enumeration .1.3.6.1.4.1.18.3.5.1.4.1.1.1 |
wfCctOptsPriorityQueueingDisablePriority Queuing optionrw Enumeration .1.3.6.1.4.1.18.3.5.1.4.1.1.2 |
wfCctOptsCctcircuit numberro INTEGER .1.3.6.1.4.1.18.3.5.1.4.1.1.3 |
wfCctOptsHighPriorityQueueLimitHigh Priority Queue limit
The minimum valid value is zero.
no maximum valid value (limited by bufs for the slot)rw Enumeration .1.3.6.1.4.1.18.3.5.1.4.1.1.4 |
wfCctOptsNormalPriorityQueueLimitNormal Priority Queue limit
The minimum valid value is zero.
no maximum valid value (limited by bufs for the slot)rw Enumeration .1.3.6.1.4.1.18.3.5.1.4.1.1.5 |
wfCctOptsLowPriorityQueueLimitLow Priority Queue limit
The minimum valid value is zero.
no maximum valid value (limited by bufs for the slot)rw Enumeration .1.3.6.1.4.1.18.3.5.1.4.1.1.6 |
wfCctOptsMaxInterruptQueueLatencyInterrupt Queue Latencyrw INTEGER .1.3.6.1.4.1.18.3.5.1.4.1.1.7 |
wfCctOptsMaxHighPriorityQueueLatencyHigh Priority Queue Latencyrw INTEGER .1.3.6.1.4.1.18.3.5.1.4.1.1.8 |
wfCctOptsHiXmitsHigh Priority Transmit countro Counter .1.3.6.1.4.1.18.3.5.1.4.1.1.9 |
wfCctOptsNormalXmitsNormal Priority Transmit countro Counter .1.3.6.1.4.1.18.3.5.1.4.1.1.10 |
wfCctOptsLoXmitsLow Priority Transmit countro Counter .1.3.6.1.4.1.18.3.5.1.4.1.1.11 |
wfCctOptsHiClippedPktsHigh Prio Transmit Clip Countro Counter .1.3.6.1.4.1.18.3.5.1.4.1.1.12 |
wfCctOptsNormalClippedPktsNormal Prio Transmit Clip Countro Counter .1.3.6.1.4.1.18.3.5.1.4.1.1.13 |
wfCctOptsLoClippedPktsLow Prio Transmit Clip Countro Counter .1.3.6.1.4.1.18.3.5.1.4.1.1.14 |
wfCctOptsIntrQHighWaterPktsInterrupt Queue high-water markro Gauge .1.3.6.1.4.1.18.3.5.1.4.1.1.15 |
wfCctOptsHiQHighWaterPktsHigh-priority Queue high-water markro Gauge .1.3.6.1.4.1.18.3.5.1.4.1.1.16 |
wfCctOptsNormalQHighWaterPktsNormal Queue high-water markro Gauge .1.3.6.1.4.1.18.3.5.1.4.1.1.17 |
wfCctOptsLoQHighWaterPktsLow-priority Queue high-water markro Gauge .1.3.6.1.4.1.18.3.5.1.4.1.1.18 |
wfCctOptsHighWaterPktsClearAttribute to clear the high-water marks. When the MIB
changes, Priority Queueing (if ENABLED) checks to see
if HighWaterPktsClear is different than the last time the MIB
was modified in any way. If it is different,
all the high water marks (see above) are set to zero.rw INTEGER .1.3.6.1.4.1.18.3.5.1.4.1.1.19 |
wfCctOptsDroppedPktsPackets which were filtered in Priority Queueingro Counter .1.3.6.1.4.1.18.3.5.1.4.1.1.20 |
wfCctOptsLargePktsLarge Packets which became an exception to latency rulesro Counter .1.3.6.1.4.1.18.3.5.1.4.1.1.21 |
wfCctOptsRxPktsPackets receivedro Counter .1.3.6.1.4.1.18.3.5.1.4.1.1.22 |
wfCctOptsChooserTypeAlgorithm to choose line within a multiline circuitrw Enumeration .1.3.6.1.4.1.18.3.5.1.4.1.1.23 |
wfCctOptsPqDequeueAlgTypeSelection of Priority Queueing dequeueing algorithm
PQ_STRICT_PRIORITIZATION is 'classical' 7.50 dequeueing.
PQ_BANDWIDTH_ALLOCATION makes exceptions to strict
prioritization in order to prevent starvation of the
Normal and/or Low priority traffic.rw Enumeration .1.3.6.1.4.1.18.3.5.1.4.1.1.24 |
wfCctOptsHiPercentThis is the percent of the SYNC line bandwidth that
the network manager wishes to allocate to traffic
which has been configured to be High Priority.
This parameter only has meaning when the bandwidth allocation
dequeueing algorithm is enabled by setting the dequeueing
algorithm type appropriately.
With this parameter
set other than 100, each time the configured percent
utilization is reached, Normal and Low traffic is
sent out (if any is queued up), up to their
configured percentages.rw Enumeration .1.3.6.1.4.1.18.3.5.1.4.1.1.25 |
wfCctOptsNormalPercentThe minimum percent of the SYNC line that Normal-priority
traffic will get (if there is any) when the Bandwidth
Allocation feature is enabled.
See text for wfCctOptsHiPercent for more information.rw Enumeration .1.3.6.1.4.1.18.3.5.1.4.1.1.26 |
wfCctOptsLoPercentThe minimum percent of the SYNC line that Low-priority traffic
will get (if there is any) when the Bandwidth Allocation
feature is enabled.
See text for wfCctOptsHiPercent for more information.rw Enumeration .1.3.6.1.4.1.18.3.5.1.4.1.1.27 |
wfCctOptsHiTotalOctetsRunning total of High Octets transmitted when
using Bandwidth Allocation dequeueing algorithmro Counter .1.3.6.1.4.1.18.3.5.1.4.1.1.28 |
wfCctOptsNormalTotalOctetsRunning total of Normal Octets transmitted when
using Bandwidth Allocation dequeueing algorithmro Counter .1.3.6.1.4.1.18.3.5.1.4.1.1.29 |
wfCctOptsLoTotalOctetsRunning total of Low Octets transmitted when
using Bandwidth Allocation dequeueing algorithmro Counter .1.3.6.1.4.1.18.3.5.1.4.1.1.30 |
wfCctOptsCircuitTypeCircuit Type Attributerw Enumeration .1.3.6.1.4.1.18.3.5.1.4.1.1.31 |
wfCctOptsBackupCctbackup circuit numberrw INTEGER .1.3.6.1.4.1.18.3.5.1.4.1.1.32 |
wfCctOptsPrimaryCctWanProtocolTypeThe type of WAN protocol type which is running
on the primary line. This attribute is only
read when a dial backup circuit is using this
mib record.rw Enumeration .1.3.6.1.4.1.18.3.5.1.4.1.1.33 |
wfCctOptsMacFilterFormatUsed to force the Mac src/dst address to be matched
in Token Ring format.rw Enumeration .1.3.6.1.4.1.18.3.5.1.4.1.1.34 |
wfCctOptsPktsNotQueuedPackets that were not Queued or Dropped by
Priority Queuingro Counter .1.3.6.1.4.1.18.3.5.1.4.1.1.35 |
wfCctOptsBitsShiftCountUsed to shift src/dst address to the right
when addressed based chooser is set.rw INTEGER .1.3.6.1.4.1.18.3.5.1.4.1.1.36 |
wfCctOptsFrSetDeLowQUsed on Frame Relay interfaces, allows Set of
DE ( Discard Eligible ) bit of packets that end up
in PQ's Low Queue, the Default is Do Set DE bitrw Enumeration .1.3.6.1.4.1.18.3.5.1.4.1.1.37 |
wfCctOptsFrSetDeNormQUsed on Frame Relay interfaces, allows Set of
DE ( Discard Eligible ) bit of packets that end up
in PQ's Normal Queue, the Default is Don't Set DE bitrw Enumeration .1.3.6.1.4.1.18.3.5.1.4.1.1.38 |
wfCctOptsShapedPriorityQueueLimitFrame Relay Traffic Shaping Priority Queue Limit.
the minimum valid value is zerom no maximum valid
value (limited by bufs for the slot).rw Enumeration .1.3.6.1.4.1.18.3.5.1.4.1.1.39 |
wfCctOptsMaxShapedPriorityQueueLatencyFrame Relay Traffic Shaping Priority Queue Latency.rw INTEGER .1.3.6.1.4.1.18.3.5.1.4.1.1.40 |
wfCctOptsShapedXmitsFrame Relay Traffic Shaping Priority Transmit count.ro Counter .1.3.6.1.4.1.18.3.5.1.4.1.1.41 |
wfCctOptsShapedClippedPktsFrame Relay Traffic Shaping Transmit Clip count.ro Counter .1.3.6.1.4.1.18.3.5.1.4.1.1.42 |
wfCctOptsShapedQHighWaterPktsFrame Relay Traffic Shaping Queue high-water mark.ro Gauge .1.3.6.1.4.1.18.3.5.1.4.1.1.43 |
wfCctOptsShapedTotalOctetsRunning total of Frame Relay Traffic Shaping octets
transmitted.ro Counter .1.3.6.1.4.1.18.3.5.1.4.1.1.44 |
wfCctOptsPpqDebugLevelProtocol Priority Queueing Debug Level.rw INTEGER .1.3.6.1.4.1.18.3.5.1.4.1.1.45 |
wfDequeueAtLineRateDetermines whether the dequeuing from the
queues is to be done at the line rate
instead of the conventional technique or
not.rw Enumeration .1.3.6.1.4.1.18.3.5.1.4.1.1.46 |
wfCctOptsBrFilterTableBridge Filters SEQUENCE OF WfCctOptsBrFilterEntry .1.3.6.1.4.1.18.3.5.1.4.2 |
wfCctOptsBrFilterEntryAn entry in WfCctOptsBrFilterTable. WfCctOptsBrFilterEntry .1.3.6.1.4.1.18.3.5.1.4.2.1 |
wfCctOptsBrFilterCreateDefines the existence of the traffic filter rule:
created - traffic filter exists
delete - traffic filter does not exist and can be deleted.rw Enumeration .1.3.6.1.4.1.18.3.5.1.4.2.1.1 |
wfCctOptsBrFilterEnableDefines whether or not the traffic filter rule should be used:
enabled - activate the rule.
disabled - inactivate the rule.rw Enumeration .1.3.6.1.4.1.18.3.5.1.4.2.1.2 |
wfCctOptsBrFilterStateDefines the current State of the traffic filter:
inactive - the rule is not in use.
active - the rule is being used.
error - the application detected an error in the rule.ro Enumeration .1.3.6.1.4.1.18.3.5.1.4.2.1.3 |
wfCctOptsBrFilterCounterThe number of received packets that have
matched this rule.ro Counter .1.3.6.1.4.1.18.3.5.1.4.2.1.4 |
wfCctOptsBrFilterDefinitionThe filter rule definition.rw OCTET STRING .1.3.6.1.4.1.18.3.5.1.4.2.1.5 |
wfCctOptsBrFilterReservedReserved field.ro INTEGER .1.3.6.1.4.1.18.3.5.1.4.2.1.6 |
wfCctOptsBrFilterCctThe ID of the CctBridge Cct to which the
filter is applied.ro INTEGER .1.3.6.1.4.1.18.3.5.1.4.2.1.7 |
wfCctOptsBrFilterRuleNumberID for the rule.ro INTEGER .1.3.6.1.4.1.18.3.5.1.4.2.1.8 |
wfCctOptsBrFilterFragmentFragment number - for large rules.ro INTEGER .1.3.6.1.4.1.18.3.5.1.4.2.1.9 |
wfCctOptsBrFilterNamename of the rule numberrw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.18.3.5.1.4.2.1.10 |
wfCctOptsIpFilterTableIp Filters SEQUENCE OF WfCctOptsIpFilterEntry .1.3.6.1.4.1.18.3.5.1.4.3 |
wfCctOptsIpFilterEntryAn entry in WfCctOptsIpFilterTable. WfCctOptsIpFilterEntry .1.3.6.1.4.1.18.3.5.1.4.3.1 |
wfCctOptsIpFilterCreateDefines the existence of the traffic filter rule:
created - traffic filter exists
delete - traffic filter does not exist and can be deleted.rw Enumeration .1.3.6.1.4.1.18.3.5.1.4.3.1.1 |
wfCctOptsIpFilterEnableDefines whether or not the traffic filter rule should be used:
enabled - activate the rule.
disabled - inactivate the rule.rw Enumeration .1.3.6.1.4.1.18.3.5.1.4.3.1.2 |
wfCctOptsIpFilterStateDefines the current State of the traffic filter:
inactive - the rule is not in use.
active - the rule is being used.
error - the application detected an error in the rule.ro Enumeration .1.3.6.1.4.1.18.3.5.1.4.3.1.3 |
wfCctOptsIpFilterCounterThe number of received packets that have
matched this rule.ro Counter .1.3.6.1.4.1.18.3.5.1.4.3.1.4 |
wfCctOptsIpFilterDefinitionThe filter rule definition.rw OCTET STRING .1.3.6.1.4.1.18.3.5.1.4.3.1.5 |
wfCctOptsIpFilterReservedReserved field.ro INTEGER .1.3.6.1.4.1.18.3.5.1.4.3.1.6 |
wfCctOptsIpFilterCctThe ID of the CctIp Cct to which the
filter is applied.ro INTEGER .1.3.6.1.4.1.18.3.5.1.4.3.1.7 |
wfCctOptsIpFilterRuleNumberID for the rule.ro INTEGER .1.3.6.1.4.1.18.3.5.1.4.3.1.8 |
wfCctOptsIpFilterFragmentFragment number - for large rules.ro INTEGER .1.3.6.1.4.1.18.3.5.1.4.3.1.9 |
wfCctOptsIpFilterNamename of the rule numberrw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.18.3.5.1.4.3.1.10 |
wfCctOptsLengthBasedTableLength Based Priority Table SEQUENCE OF WfCctOptsLengthBasedEntry .1.3.6.1.4.1.18.3.5.1.4.4 |
wfCctOptsLengthBasedEntryAn entry in WfCctOptsLengthBasedTable. WfCctOptsLengthBasedEntry .1.3.6.1.4.1.18.3.5.1.4.4.1 |
wfCctOptsLengthBasedDeleteDefines the existence of the length based priority filter rule:
created - traffic filter exists
delete - traffic filter does not exist and can be deleted.rw Enumeration .1.3.6.1.4.1.18.3.5.1.4.4.1.1 |
wfCctOptsLengthBasedDisableDefines whether or not the length based priority filter rule should be used:
enabled - activate the rule.
disabled - inactivate the rule.rw Enumeration .1.3.6.1.4.1.18.3.5.1.4.4.1.2 |
wfCctOptsLengthBasedStateDefines the current State of the length based priority filter:
inactive - the rule is not in use.
active - the rule is being used.
error - the application detected an error in the rule.ro Enumeration .1.3.6.1.4.1.18.3.5.1.4.4.1.3 |
wfCctOptsLengthBasedCctThe ID of the Cct to which the filter is appliedro INTEGER .1.3.6.1.4.1.18.3.5.1.4.4.1.4 |
wfCctOptsLengthBasedMuxpacket mux typero Enumeration .1.3.6.1.4.1.18.3.5.1.4.4.1.5 |
wfCctOptsLengthBasedDataa five byte quantity of the form
ethernet - 0x6003000000 (e.g. DECnet)
lsap - 0xfefe030000 (e.g. OSI)
snap - 0x0000000800 (e.g. IP)
- 0x0800070800 (e.g. Appletalk DDP)ro OCTET STRING .1.3.6.1.4.1.18.3.5.1.4.4.1.6 |
wfCctOptsLengthBasedLengthMaximum length of a packet to be considered high priorityrw INTEGER .1.3.6.1.4.1.18.3.5.1.4.4.1.7 |
wfCctOptsLengthBasedLessThanQqueue into which packets of length less than or equal
wfCctOptsLengthBasedLength are placedrw Enumeration .1.3.6.1.4.1.18.3.5.1.4.4.1.8 |
wfCctOptsLengthBasedGreaterThanQqueue into which packets of length greater than
wfCctOptsLengthBasedLength are placedrw Enumeration .1.3.6.1.4.1.18.3.5.1.4.4.1.9 |
wfSwservOptsTableThe table of circuits defined over switched services SEQUENCE OF WfSwservOptsEntry .1.3.6.1.4.1.18.3.5.1.4.5 |
wfSwservOptsEntryEntry format for the table of sw_serv circuit options WfSwservOptsEntry .1.3.6.1.4.1.18.3.5.1.4.5.1 |
wfSwservOptsDeleteCreation and deletion flagrw Enumeration .1.3.6.1.4.1.18.3.5.1.4.5.1.1 |
wfSwservOptsCctCircuit Numberro INTEGER .1.3.6.1.4.1.18.3.5.1.4.5.1.2 |
wfSwservOptsCircuitTypeCircuit Type Attributerw Enumeration .1.3.6.1.4.1.18.3.5.1.4.5.1.3 |
wfSwservOptsBackupCctBackup Circuit Number assigned by site managerrw INTEGER .1.3.6.1.4.1.18.3.5.1.4.5.1.4 |
wfSwservOptsBackupPoolBackup Pool Idrw INTEGER .1.3.6.1.4.1.18.3.5.1.4.5.1.5 |
wfSwservOptsDemandPoolDial on Demand Pool Idrw INTEGER .1.3.6.1.4.1.18.3.5.1.4.5.1.6 |
wfSwservOptsBackupModeMode Master ( initiate dialing ) or Slaverw Enumeration .1.3.6.1.4.1.18.3.5.1.4.5.1.7 |
wfSwservOptsActiveBackupCctActive Backup Indicatorrw INTEGER .1.3.6.1.4.1.18.3.5.1.4.5.1.8 |
wfSwservOptsForcedDialForced Dial Indicatorrw Enumeration .1.3.6.1.4.1.18.3.5.1.4.5.1.9 |
wfSwservOptsMaxUpTimeMax amount fo time dial call can existrw INTEGER .1.3.6.1.4.1.18.3.5.1.4.5.1.10 |
wfSwservOptsBringUpHourTime of day hour to allow a line to dialrw INTEGER .1.3.6.1.4.1.18.3.5.1.4.5.1.11 |
wfSwservOptsBringUpMinuteTime of day minute to allow a line to dialrw INTEGER .1.3.6.1.4.1.18.3.5.1.4.5.1.12 |
wfSwservOptsTakeDownHourTime of day hour to take down a dial linerw INTEGER .1.3.6.1.4.1.18.3.5.1.4.5.1.13 |
wfSwservOptsTakeDownMinuteTime of day minute to take down a dial linerw INTEGER .1.3.6.1.4.1.18.3.5.1.4.5.1.14 |
wfSwservOptsInactivityTimeMaximum for inactivity timer is equal to
infinity = 99999999rw INTEGER .1.3.6.1.4.1.18.3.5.1.4.5.1.15 |
wfSwservOptsCircuitStateCircuit Statero Enumeration .1.3.6.1.4.1.18.3.5.1.4.5.1.16 |
wfSwservOptsPrimaryDownTimeAmount of time allowed for establishment of primary before
the backup is invokedrw Enumeration .1.3.6.1.4.1.18.3.5.1.4.5.1.17 |
wfSwservOptsNumOutgoingConnNumber of Outgoing call attempts for this circuitro Counter .1.3.6.1.4.1.18.3.5.1.4.5.1.18 |
wfSwservOptsNumIncomingConnNumber of Incoming call attempts for this circuitro Counter .1.3.6.1.4.1.18.3.5.1.4.5.1.19 |
wfSwservOptsActiveSlotSlot actively in use by this callro INTEGER .1.3.6.1.4.1.18.3.5.1.4.5.1.20 |
wfSwservOptsActiveLineLine actively in use by this callro INTEGER .1.3.6.1.4.1.18.3.5.1.4.5.1.21 |
wfSwservOptsPacketsDroppedNumber of Incoming call attempts for this circuitro Counter .1.3.6.1.4.1.18.3.5.1.4.5.1.22 |
wfSwservOptsTimeLastPktDroppedNumber of Incoming call attempts for this circuitro INTEGER .1.3.6.1.4.1.18.3.5.1.4.5.1.23 |
wfSwservOptsForcedTakedownForced Dial Indicatorrw Enumeration .1.3.6.1.4.1.18.3.5.1.4.5.1.24 |
wfSwservOptsRetryMaxRedial countrw INTEGER .1.3.6.1.4.1.18.3.5.1.4.5.1.25 |
wfSwservOptsRetryCountRedial countro Counter .1.3.6.1.4.1.18.3.5.1.4.5.1.26 |
wfSwservOptsRetryDelaydelay to wait after retrys fails. value is in secondsrw INTEGER .1.3.6.1.4.1.18.3.5.1.4.5.1.27 |
wfSwservOptsDemandConnectionModeMode Master - outgoing call has precedence terminate
incoming call
Slave - incoming call has precedence terminate
outgoing call
NO_Dial - if data is present do MOT establish connection
just drop the datarw Enumeration .1.3.6.1.4.1.18.3.5.1.4.5.1.28 |
wfSwservOptsAutoDemandTerminationAutomatically terminates demand circuit if
maximum connect attempts reachedrw Enumeration .1.3.6.1.4.1.18.3.5.1.4.5.1.29 |
wfSwservOptsAutoDemandTermResetAmount of time ( in Minutes )before atttempting to recreate
the demand circuit after an auto terminationrw INTEGER .1.3.6.1.4.1.18.3.5.1.4.5.1.30 |
wfSwservOptsChapLocalNameThis attribute is used to assign a local CHAP Name to
outbound calls to to inform our peer of our identity,
during WHOAMI processingrw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.18.3.5.1.4.5.1.31 |
wfSwservOptsChapSecretSecret used for running CHAP when this cct is active.
The peer must use the same secret when responding to our
Challenges, which will be found in the Whoami Tablerw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.18.3.5.1.4.5.1.32 |
wfSwservOptsMaxUpTerminationAutomatically terminates demand circuit if
maximum connect attempts reachedrw Enumeration .1.3.6.1.4.1.18.3.5.1.4.5.1.33 |
wfSwservOptsMaxUpTermResetAmount of time ( in Minutes )before atttempting to recreate
the demand circuit after an auto terminationrw INTEGER .1.3.6.1.4.1.18.3.5.1.4.5.1.34 |
wfSwservOptsBandwidthPoolBandwidth on Demand Pool Idrw INTEGER .1.3.6.1.4.1.18.3.5.1.4.5.1.35 |
wfSwservOptsBandwidthModeBandwidth Mode Monitor (Congestion Monitor) or NORMALrw Enumeration .1.3.6.1.4.1.18.3.5.1.4.5.1.36 |
wfSwservOptsPapIdThis attribute is used to assign a local PAP Id to
outbound calls to to inform our peer of our identity,
during WHOAMI processingrw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.18.3.5.1.4.5.1.37 |
wfSwservOptsPapPasswordThis attribute is used to assign a local PAP Password
to outbound calls to to inform our peer of our identity,
during WHOAMI processingrw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.18.3.5.1.4.5.1.38 |
wfSwservOptsDebugMsgLevelThis attribute is used to assign the level of Swserv Debug
message to be logged for the circuitrw Enumeration .1.3.6.1.4.1.18.3.5.1.4.5.1.39 |
wfSwservOptsDmdCctGroupNumBackup Circuit Number assigned by site managerrw INTEGER .1.3.6.1.4.1.18.3.5.1.4.5.1.40 |
wfSwservOptsWanProtocolWan Protocol for this circuit assigned by site manager.
Used by BNX Software to Support ISDN Switched access
to Frame Relay Switch Network.rw Enumeration .1.3.6.1.4.1.18.3.5.1.4.5.1.41 |
wfSwservOptsSecondaryCctSecondary circuit to be used by Line Manager when
creating a backup for this primary circuit.rw INTEGER .1.3.6.1.4.1.18.3.5.1.4.5.1.42 |
wfSwservOptsPoolLineNumberPooling line number used for identifying Frame Relay backup
interface objects associated with a pool.rw INTEGER .1.3.6.1.4.1.18.3.5.1.4.5.1.43 |
wfSwservOptsPoolLineIndexLower layer index used for identifying Frame Relay backup
interface objects associated with a pool.rw INTEGER .1.3.6.1.4.1.18.3.5.1.4.5.1.44 |
wfSwservOptsMinDurationMaximum for min duration timer in seconds is equal to
infinity = 99999999, min is 10rw INTEGER .1.3.6.1.4.1.18.3.5.1.4.5.1.45 |
wfSwservOptsInactivityModeInactivity check moderw Enumeration .1.3.6.1.4.1.18.3.5.1.4.5.1.46 |
wfSwservOptsOpportunityRoutingOpportunityRouting Indicatorrw Enumeration .1.3.6.1.4.1.18.3.5.1.4.5.1.47 |
wfSwservOptsOutboundAuthAllows the disabling of Authentication when the router is
placing an outbound call.rw Enumeration .1.3.6.1.4.1.18.3.5.1.4.5.1.48 |
wfSwservOptsOverSubRetryTimerThis parameter allows the user to cofigure the time
period at which a connection will be retried, if
a previous connection attempt for routing updates failed
due to lack of line resources. This time should be less than
the stabilization timer for IP/IPX protocols. This time is
expressed in minutes and is meaningful only if Dial Optimized
Routing is enabled.rw INTEGER .1.3.6.1.4.1.18.3.5.1.4.5.1.49 |
wfSwservOptsStandbyModeThis parameter allows a demand circuit to be identified as standby
or demand. The hot standby circuit is down until an event invokes
it. Normal standby is invoked manually or by an incoming call.rw Enumeration .1.3.6.1.4.1.18.3.5.1.4.5.1.50 |
wfSwservOptsStandbyFailBackModeThis parameter is used to indicate if standby failback should be
automatic or manual.rw Enumeration .1.3.6.1.4.1.18.3.5.1.4.5.1.51 |
wfSwservOptsManualStandbyActionThis parameter is used to manually activate and deactivate
a standby circuit.rw Enumeration .1.3.6.1.4.1.18.3.5.1.4.5.1.52 |
wfSwservOptsCallbackModeDefines the role this circuit will play in Callback.
INACTIVE disables Callback on this circuit.
SERVER performs Callback via Outgoing Phone Number.
CLIENT circuit expects peer to perform Callback.
SERVER_CALLID performs Callback via ANIrw Enumeration .1.3.6.1.4.1.18.3.5.1.4.5.1.53 |
wfSwservOptsCallbackServerDelayThe amount of time the CALLBACK_SERVER will wait,
(in seconds) before performing Callback,dialing back
the initial caller. The default time is 0, however modem
connections may need some delay configured to prevent busy
situations.rw INTEGER .1.3.6.1.4.1.18.3.5.1.4.5.1.54 |
wfSwservOptsCallbackClientDelayThe amount of time the CALLBACK_CLIENT will wait,
(in seconds) for its peer to perform Callback. Data ariving
during opperation of the timer, will not cause a connection
to be established.rw INTEGER .1.3.6.1.4.1.18.3.5.1.4.5.1.55 |
wfSwservOptsQueueSizeThis parameter controls the length of the queue used for
dial services.rw INTEGER .1.3.6.1.4.1.18.3.5.1.4.5.1.56 |
wfSwservOptsDequeueWaitTimerThis parameter controls the time FR waits before dequeuing
data for FRDOD.rw INTEGER .1.3.6.1.4.1.18.3.5.1.4.5.1.57 |
wfSwservOptsMruThis is the MRU being used for this demand circuit.rw INTEGER .1.3.6.1.4.1.18.3.5.1.4.5.1.58 |
wfSwservOptsRfc1661ComplianceEnable/disable RFC 1661 compliancerw Enumeration .1.3.6.1.4.1.18.3.5.1.4.5.1.59 |
wfSwservOptsBootupDelayDelay in initiation of the DoD circuit at bootup timerw INTEGER .1.3.6.1.4.1.18.3.5.1.4.5.1.60 |
wfSwservOptsCallbackOptRfc1570The PPP/LCP Callback Option; indicates the type of
data content the callback client places in
wfSwservOptsCallbackDataRfc1570 for the callback serverrw Enumeration .1.3.6.1.4.1.18.3.5.1.4.5.1.61 |
wfSwservOptsCallbackDataRfc1570The PPP/LCP Callback Data; the actual callback client
data which is sent to the callback server for processingrw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.18.3.5.1.4.5.1.62 |
wfSwservOutPhoneNumTable***************************************
SWSERV outgoing phone number list SEQUENCE OF WfSwservOutPhoneNumEntry .1.3.6.1.4.1.18.3.5.1.4.6 |
wfSwservOutPhoneNumEntryAn entry in the SWSERV_SYNC table WfSwservOutPhoneNumEntry .1.3.6.1.4.1.18.3.5.1.4.6.1 |
wfSwservOutPhoneNumDeleteDelete this phone number from the listrw Enumeration .1.3.6.1.4.1.18.3.5.1.4.6.1.1 |
wfSwservOutPhoneNumCctCCT number for this phone list instancero INTEGER .1.3.6.1.4.1.18.3.5.1.4.6.1.2 |
wfSwservOutPhoneNumIndexa unique one up type number to create a listro INTEGER .1.3.6.1.4.1.18.3.5.1.4.6.1.3 |
wfSwservOutPhoneNumRmtStationNumthe station address (phone number) of the remote systemrw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.18.3.5.1.4.6.1.4 |
wfSwservOutPhoneNumSubAddrfor Swserv phone numbers, the sub address portionrw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.18.3.5.1.4.6.1.5 |
wfSwservOutPhoneNumDelimiterfor Swserv phone numbers, the delimiter portionrw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.18.3.5.1.4.6.1.6 |
wfSwservOutPhoneNumTypephone number types; ISDN types, Modem Sync Dial or Async
Dial typesrw Enumeration .1.3.6.1.4.1.18.3.5.1.4.6.1.7 |
wfSwservOutPhoneNumTypeofNumIF ISDN type number, it needs type of number
UNKNOWN Type is 0, use 1 to satisfy MDL requirement
This attribute value will be ANDED with 0xFFF0 before using it.rw Enumeration .1.3.6.1.4.1.18.3.5.1.4.6.1.8 |
wfSwservOutPhoneNumPlanIf Isdn and if type of number is UNKNOWN or INERNATIONAL or NATIONAL
or SUBSCRIBER then a plan number is needed. UNKNOWN is 0 ,
using 16 (0x10)to satisfy MDL requirement. We will AND this field with
0x0F before using it.rw Enumeration .1.3.6.1.4.1.18.3.5.1.4.6.1.9 |
wfSwservOutPhoneNumRateAdaptionIf Isdn and if a specifis Transfer rate is to be requested when
establishing a call to this distination address specify the desired
rate.rw Enumeration .1.3.6.1.4.1.18.3.5.1.4.6.1.10 |
wfSwservOutPhoneNumRemotePoolTypeSpecify the types of calls accepted by the remote router on this port.
For example, if the port on the remote router resides in only a demand
pool specify the port type for this phone number to be dialondemand.rw Enumeration .1.3.6.1.4.1.18.3.5.1.4.6.1.11 |
wfSwservOutPhoneNumConnectionTypeSpecify if this phone number can be used to receive a single call or multiple calls.rw Enumeration .1.3.6.1.4.1.18.3.5.1.4.6.1.12 |
wfSwservOutPhoneNumChannelTypeType of Channels used for the outgoing call.rw Enumeration .1.3.6.1.4.1.18.3.5.1.4.6.1.13 |
wfSwservOutPhoneNumAggrChanCntMultiplier for the Multirate call.rw INTEGER .1.3.6.1.4.1.18.3.5.1.4.6.1.14 |
wfSwservOutPhoneNumPrefixPhone number prefix such as hayes dial command.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.18.3.5.1.4.6.1.15 |
wfSwservOutPhoneNumBearerServiceThe Bearer service - data or voice, for ISDN call setup using this numberrw Enumeration .1.3.6.1.4.1.18.3.5.1.4.6.1.16 |
wfSwservInPhoneNumTableSWSERV Ingoing phone number list SEQUENCE OF WfSwservInPhoneNumEntry .1.3.6.1.4.1.18.3.5.1.4.7 |
wfSwservInPhoneNumEntryAn entry in the Swserv_SYNC table WfSwservInPhoneNumEntry .1.3.6.1.4.1.18.3.5.1.4.7.1 |
wfSwservInPhoneNumDeleteDelete this phone number from the listrw Enumeration .1.3.6.1.4.1.18.3.5.1.4.7.1.1 |
wfSwservInPhoneNumIndexa unique one up type number to create a listro INTEGER .1.3.6.1.4.1.18.3.5.1.4.7.1.2 |
wfSwservInPhoneNumRmtStationNumthe station address (phone number) of the remote systemrw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.18.3.5.1.4.7.1.3 |
wfSwservInPhoneNumSubAddrfor Swserv phone numbers, the sub address portionrw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.18.3.5.1.4.7.1.4 |
wfSwservInPhoneNumDelimiterfor Swserv phone numbers, the delimiter portionrw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.18.3.5.1.4.7.1.5 |
wfSwservInPhoneNumTypephone number types; ISDN types or Modem Dial typesrw Enumeration .1.3.6.1.4.1.18.3.5.1.4.7.1.6 |
wfSwservInPhoneNumTypeofNumWe will AND this field with 0x0xFFF0 before using it.rw Enumeration .1.3.6.1.4.1.18.3.5.1.4.7.1.7 |
wfSwservInPhoneNumPlan0x0F before using it.rw Enumeration .1.3.6.1.4.1.18.3.5.1.4.7.1.8 |
wfSwservInPhoneNumCctIdentifies which circuit should be used when performing
Callback. If Null, Authentication must complete before
Callback can occur.rw INTEGER .1.3.6.1.4.1.18.3.5.1.4.7.1.9 |
wfCctOptsBrBuPppFilterTableDial Backup PPP Datalink filter table SEQUENCE OF WfCctOptsBrBuPppFilterEntry .1.3.6.1.4.1.18.3.5.1.4.8 |
wfCctOptsBrBuPppFilterEntryAn entry in WfCctOptsBrBuPppFilterTable. WfCctOptsBrBuPppFilterEntry .1.3.6.1.4.1.18.3.5.1.4.8.1 |
wfCctOptsBrBuPppFilterCreateDefines the existence of the traffic filter rule:
created - traffic filter exists
delete - traffic filter does not exist and can be deleted.rw Enumeration .1.3.6.1.4.1.18.3.5.1.4.8.1.1 |
wfCctOptsBrBuPppFilterEnableDefines whether or not the traffic filter rule should be used:
enabled - activate the rule.
disabled - inactivate the rule.rw Enumeration .1.3.6.1.4.1.18.3.5.1.4.8.1.2 |
wfCctOptsBrBuPppFilterStateDefines the current State of the traffic filter:
inactive - the rule is not in use.
active - the rule is being used.
error - the application detected an error in the rule.ro Enumeration .1.3.6.1.4.1.18.3.5.1.4.8.1.3 |
wfCctOptsBrBuPppFilterCounterThe number of received packets that have
matched this rule.ro Counter .1.3.6.1.4.1.18.3.5.1.4.8.1.4 |
wfCctOptsBrBuPppFilterDefinitionThe filter rule definition.rw OCTET STRING .1.3.6.1.4.1.18.3.5.1.4.8.1.5 |
wfCctOptsBrBuPppFilterReservedReserved field.ro INTEGER .1.3.6.1.4.1.18.3.5.1.4.8.1.6 |
wfCctOptsBrBuPppFilterCctThe ID of the CctBridge Cct to which the
filter is applied.ro INTEGER .1.3.6.1.4.1.18.3.5.1.4.8.1.7 |
wfCctOptsBrBuPppFilterRuleNumberID for the rule.ro INTEGER .1.3.6.1.4.1.18.3.5.1.4.8.1.8 |
wfCctOptsBrBuPppFilterFragmentFragment number - for large rules.ro INTEGER .1.3.6.1.4.1.18.3.5.1.4.8.1.9 |
wfCctOptsBrBuPppFilterNamename of the rule numberrw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.18.3.5.1.4.8.1.10 |
wfCctOptsIpBuPppFilterTableIP Filter Table for Backup Lines SEQUENCE OF WfCctOptsIpBuPppFilterEntry .1.3.6.1.4.1.18.3.5.1.4.9 |
wfCctOptsIpBuPppFilterEntryAn entry in WfCctOptsIpBuPppFilterTable. WfCctOptsIpBuPppFilterEntry .1.3.6.1.4.1.18.3.5.1.4.9.1 |
wfCctOptsIpBuPppFilterCreateDefines the existence of the traffic filter rule:
created - traffic filter exists
delete - traffic filter does not exist and can be deleted.rw Enumeration .1.3.6.1.4.1.18.3.5.1.4.9.1.1 |
wfCctOptsIpBuPppFilterEnableDefines whether or not the traffic filter rule should be used:
enabled - activate the rule.
disabled - inactivate the rule.rw Enumeration .1.3.6.1.4.1.18.3.5.1.4.9.1.2 |
wfCctOptsIpBuPppFilterStateDefines the current State of the traffic filter:
inactive - the rule is not in use.
active - the rule is being used.
error - the application detected an error in the rule.ro Enumeration .1.3.6.1.4.1.18.3.5.1.4.9.1.3 |
wfCctOptsIpBuPppFilterCounterThe number of received packets that have
matched this rule.ro Counter .1.3.6.1.4.1.18.3.5.1.4.9.1.4 |
wfCctOptsIpBuPppFilterDefinitionThe filter rule definition.rw OCTET STRING .1.3.6.1.4.1.18.3.5.1.4.9.1.5 |
wfCctOptsIpBuPppFilterReservedReserved field.ro INTEGER .1.3.6.1.4.1.18.3.5.1.4.9.1.6 |
wfCctOptsIpBuPppFilterCctThe ID of the CctBridge Cct to which the
filter is applied.ro INTEGER .1.3.6.1.4.1.18.3.5.1.4.9.1.7 |
wfCctOptsIpBuPppFilterRuleNumberID for the rule.ro INTEGER .1.3.6.1.4.1.18.3.5.1.4.9.1.8 |
wfCctOptsIpBuPppFilterFragmentFragment number - for large rules.ro INTEGER .1.3.6.1.4.1.18.3.5.1.4.9.1.9 |
wfCctOptsIpBuPppFilterNamename of the rule numberrw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.18.3.5.1.4.9.1.10 |
wfCctOptsCngcTableBNX Switch congestion control Table SEQUENCE OF WfCctOptsCngcEntry .1.3.6.1.4.1.18.3.5.1.4.10 |
wfCctOptsCngcEntryAn entry in WfCctOptsCngcTable. WfCctOptsCngcEntry .1.3.6.1.4.1.18.3.5.1.4.10.1 |
wfCctOptsCngcDeleteDefines the existence of the congestion control entry
CNGC_CREATED - congestion control entry exists
CNGC_DELETED - congestion control entry does not exist and can
be deleted.rw Enumeration .1.3.6.1.4.1.18.3.5.1.4.10.1.1 |
wfCctOptsCngcDisableDefines whether congestion control is enabled or disabled on the
circuitrw Enumeration .1.3.6.1.4.1.18.3.5.1.4.10.1.2 |
wfCctOptsCngcCctThe circuit number of the circuit to which the entry is appliedro INTEGER .1.3.6.1.4.1.18.3.5.1.4.10.1.3 |
wfCctOptsCngcSmdsDiscardabilityThis is obsolete in V5.0 and upwards.
Defines how SMDS packets entering BNX network through
SMDS SSI and SMDS SNI interfaces should be treated at this
circuit during congestion for dropping. This is applicable
only on the internodal links.
CNGC_FRDE - treat this like Frame relay DE frame.
CNGC_FRNDE - treat this like Frame Relay non DE frame
CNGC_DATAGRAM - treat this like a datagram packet.rw Enumeration .1.3.6.1.4.1.18.3.5.1.4.10.1.4 |
wfCctOptsCngcCfgSwtxqThresholdThis is obsolete in V5.0 and upwards.
Defines the user configured software transmit queue threshold.
If this is set to NULL_VAL then the switch calculates
the default value depending on the media and uses the default value.
The default value is recommended.rw INTEGER .1.3.6.1.4.1.18.3.5.1.4.10.1.5 |
wfCctOptsCngcSwtxqThresholdThis is obsolete in V5.0 and upwards.
Defines the software transmit queue threshold in use.
Switch updates this attribute to inform user what the
current software transmit queue threshold is.ro INTEGER .1.3.6.1.4.1.18.3.5.1.4.10.1.6 |
wfCctOptsCngcCngLevel0ThresholdThis is obsolete in V5.0 and upwards.
Defines the Software Transmit Queue congestion level 0 threshold
as a percentage of the Software Transmit Queue Threshold.
The default value is recommended.rw INTEGER .1.3.6.1.4.1.18.3.5.1.4.10.1.7 |
wfCctOptsCngcCngLevel1ThresholdThis is obsolete in V5.0 and upwards.
Defines the Software Transmit Queue congestion level 1 threshold
as a percentage of the Software Transmit Queue Threshold.
The default value is recommended.
wfCctOptsCngcCngLevel1Threshold should be more than
wfCctOptsCngcCngLevel0Threshold, otherwise there will be no
congestion level 1.rw INTEGER .1.3.6.1.4.1.18.3.5.1.4.10.1.8 |
wfCctOptsCngcCngLevel2ThresholdThis is obsolete in V5.0 and upwards.
Defines the Software Transmit Queue congestion level 2 threshold
as a percentage of the Software Transmit Queue Threshold.
The default value is recommended.
wfCctOptsCngcCngLevel2Threshold should be more than
wfCctOptsCngcCngLevel1Threshold, otherwise there will be no
congestion level 2.rw INTEGER .1.3.6.1.4.1.18.3.5.1.4.10.1.9 |
wfCctOptsCngcLinkTypeDefines whether the circuit is an access link or inter-nodal
link (trunk).
Traffic monitoring, traffic priority determination, traffic
discardability level determination are done at access link and each
incoming packet on an access link is tagged with the information.
Inter-nodal link (trunk) uses the above tagged information in packets
for priority queueing and discarding packets during congestion.
WARNING - It is important to set the appropriate link type for this
attribute otherwise congestion control will not work. The default
value for this attribute is access link. This attribute value
must be changed to CNGC_LINK_INTER_NODAL for inter-nodal link(trunk).rw Enumeration .1.3.6.1.4.1.18.3.5.1.4.10.1.10 |
wfCctOptsCngcTrfPriorityEnableDefines whether traffic prioritization is enabled or disabled
on the circuit.rw Enumeration .1.3.6.1.4.1.18.3.5.1.4.10.1.11 |
wfCctOptsCngcPortIPTrfPriorityDefines the traffic priority for transmitting Non Frame Relay
or SMDS traffic on this port.
CNGC_IPPRIORITY_TWO - Default Value
Set all non FR or SMDS user traffic packets to priority 2.
CNGC_IPPRIORITY_ONE - Set all non FR or SMDS packets to priority 1.
CNGC_IPPRIORITY_TWO - Set all non FR or SMDS packets to priority 2.
CNGC_IPPRIORITY_THREE - Set all non FR or SMDS packets to priority 3.rw Enumeration .1.3.6.1.4.1.18.3.5.1.4.10.1.12 |
wfCctOptsCngcPortTrfDiscardLvlDefines at what congestion level the incoming packets on this
port should be discarded in the network.
CNGC_DISCARD_AT_LVL_TWO - Discard FR DE packets at level 2,
discard FR non DE packets at level 4,
discard SMDS packets at level 3,
discard IP packets at level 3.
Default value
CNGC_DISCARD_AT_LVL_ONE - discard all at level 1
CNGC_DISCARD_AT_LVL_TWO - discard all at level 2
CNGC_DISCARD_AT_LVL_THREE - discard all at level 3
CNGC_DISCARD_AT_LVL_FOUR - discard all at level 4rw Enumeration .1.3.6.1.4.1.18.3.5.1.4.10.1.13 |
wfCctOptsCngcPortTrfPriorityDefines the traffic priority level of all the incoming packets
on this port.
CNGC_PRIORITY_TWO - Default value
Set all incoming user traffic packets to priority 2.
CNGC_PRIORITY_ONE - Set all incoming packets to priority 1.
CNGC_PRIORITY_TWO - Set all incoming packets to priority 2.
CNGC_PRIORITY_THREE - Set all incoming packets to priority 3.
Priority 0 is reserved for network critical packets like
OSPF, FR LMI and SMDS heartbeat, Cross Net polling and is
not available for user traffic.rw Enumeration .1.3.6.1.4.1.18.3.5.1.4.10.1.14 |
wfCctOptsCngcCfgHwtxQThresholdDefines the user configured hardware transmit queue threshold.
NULL_VAL - Switch calculates the appropriate value based on
system resources and uses the value. This is recommended.
CNGC_HWTXQ_MINIMUM - minimum value to be used.
CNGC_HWTXQ_MAXIMUM - maximum value to be used.rw INTEGER .1.3.6.1.4.1.18.3.5.1.4.10.1.15 |
wfCctOptsCngcHwtxQThresholdThe current hardware queue thresholdro INTEGER .1.3.6.1.4.1.18.3.5.1.4.10.1.16 |
wfCctOptsCngcSndTrapForPktsDroppedSwitch sends a congestion notification trap for every
wfCctOptsCngcSndTrapForPktsDropped number of packets dropped.rw INTEGER .1.3.6.1.4.1.18.3.5.1.4.10.1.17 |
wfCctOptsCngcCfgQp0ThresholdDefines the Priority 0 queue threshold
NULL_VAL - Switch calculates the appropriate value based on
system resources and uses the value. This is recommended.rw INTEGER .1.3.6.1.4.1.18.3.5.1.4.10.1.18 |
wfCctOptsCngcQp0Thresholdcurrent Priority 0 queue thresholdro INTEGER .1.3.6.1.4.1.18.3.5.1.4.10.1.19 |
wfCctOptsCngcQp0CngLvl0ThresholdDefines priority 0 queue congestion level 0 threshold as a
percentage of priority 0 queue threshold.rw INTEGER .1.3.6.1.4.1.18.3.5.1.4.10.1.20 |
wfCctOptsCngcQp0CngLvl1ThresholdDefines priority 0 queue congestion level 1 threshold as a
percentage of priority 0 queue threshold.
The value of this attribute should be greater than
wfCctOptsCngcQp0CngLvl0Threshold, otherwise there will be no
priority 0 queue congestion level 1.rw INTEGER .1.3.6.1.4.1.18.3.5.1.4.10.1.21 |
wfCctOptsCngcQp0CngLvl2ThresholdDefines priority 0 queue congestion level 2 threshold as a
percentage of priority 0 queue threshold.
The value of this attribute should be greater than
wfCctOptsCngcQp0CngLvl1Threshold, otherwise there will be no
priority 0 queue congestion level 2.rw INTEGER .1.3.6.1.4.1.18.3.5.1.4.10.1.22 |
wfCctOptsCngcQp0PktsServPriNxtQDefines the number of priority 0 queue packets to be served
prior to serving each priority 1 queue packet. If priority 0 queue
is empty then priority 1 queue packets are served.rw INTEGER .1.3.6.1.4.1.18.3.5.1.4.10.1.23 |
wfCctOptsCngcCfgQp1ThresholdDefines the Priority 1 queue threshold
NULL_VAL - Switch calculates the appropriate value based on
system resources and uses the value. This is recommended.rw INTEGER .1.3.6.1.4.1.18.3.5.1.4.10.1.24 |
wfCctOptsCngcQp1Thresholdcurrent Priority 0 queue thresholdro INTEGER .1.3.6.1.4.1.18.3.5.1.4.10.1.25 |
wfCctOptsCngcQp1CngLvl0ThresholdDefines priority 1 queue congestion level 0 threshold as a
percentage of priority 1 queue threshold.rw INTEGER .1.3.6.1.4.1.18.3.5.1.4.10.1.26 |
wfCctOptsCngcQp1CngLvl1ThresholdDefines priority 1 queue congestion level 1 threshold as a
percentage of priority 1 queue threshold.
The value of this attribute should be greater than
wfCctOptsCngcQp1CngLvl0Threshold, otherwise there will be no
priority 1 queue congestion level 1.rw INTEGER .1.3.6.1.4.1.18.3.5.1.4.10.1.27 |
wfCctOptsCngcQp1CngLvl2ThresholdDefines priority 1 queue congestion level 2 threshold as a
percentage of priority 1 queue threshold.
The value of this attribute should be greater than
wfCctOptsCngcQp1CngLvl1Threshold, otherwise there will be no
priority 1 queue congestion level 2.rw INTEGER .1.3.6.1.4.1.18.3.5.1.4.10.1.28 |
wfCctOptsCngcQp1PktsServPriNxtQDefines the number of priority 1 queue packets to be served
prior to serving each priority 2 queue packet. If priority 1 queue
is empty then priority 2 queue packets are served.rw INTEGER .1.3.6.1.4.1.18.3.5.1.4.10.1.29 |
wfCctOptsCngcCfgQp2ThresholdDefines the Priority 2 queue threshold
NULL_VAL - Switch calculates the appropriate value based on
system resources and uses the value. This is recommended.rw INTEGER .1.3.6.1.4.1.18.3.5.1.4.10.1.30 |
wfCctOptsCngcQp2Thresholdcurrent Priority 0 queue thresholdro INTEGER .1.3.6.1.4.1.18.3.5.1.4.10.1.31 |
wfCctOptsCngcQp2CngLvl0ThresholdDefines priority 2 queue congestion level 0 threshold as a
percentage of priority 2 queue threshold.rw INTEGER .1.3.6.1.4.1.18.3.5.1.4.10.1.32 |
wfCctOptsCngcQp2CngLvl1ThresholdDefines priority 2 queue congestion level 1 threshold as a
percentage of priority 2 queue threshold.
The value of this attribute should be greater than
wfCctOptsCngcQp2CngLvl0Threshold, otherwise there will be no
priority 2 queue congestion level 1.rw INTEGER .1.3.6.1.4.1.18.3.5.1.4.10.1.33 |
wfCctOptsCngcQp2CngLvl2ThresholdDefines priority 2 queue congestion level 2 threshold as a
percentage of priority 2 queue threshold.
The value of this attribute should be greater than
wfCctOptsCngcQp2CngLvl1Threshold, otherwise there wil be no
priority 2 queue congestion level 2.rw INTEGER .1.3.6.1.4.1.18.3.5.1.4.10.1.34 |
wfCctOptsCngcQp2PktsServPriNxtQDefines the number of priority 2 queue packets to be served
prior to serving each priority 3 queue packet. If priority 2 queue
is empty then priority 3 queue packets are served.rw INTEGER .1.3.6.1.4.1.18.3.5.1.4.10.1.35 |
wfCctOptsCngcCfgQp3ThresholdDefines the Priority 3 queue threshold
NULL_VAL - Switch calculates the appropriate value based on
system resources and uses the value. This is recommended.rw INTEGER .1.3.6.1.4.1.18.3.5.1.4.10.1.36 |
wfCctOptsCngcQp3Thresholdcurrent Priority 3 queue thresholdro INTEGER .1.3.6.1.4.1.18.3.5.1.4.10.1.37 |
wfCctOptsCngcQp3CngLvl0ThresholdDefines priority 3 queue congestion level 0 threshold as a
percentage of priority 3 queue threshold.rw INTEGER .1.3.6.1.4.1.18.3.5.1.4.10.1.38 |
wfCctOptsCngcQp3CngLvl1ThresholdDefines priority 3 queue congestion level 1 threshold as a
percentage of priority 3 queue threshold.
The value of this attribute should be greater than
wfCctOptsCngcQp3CngLvl0Threshold, otherwise there will be no
priority 3 queue congestion level 1.rw INTEGER .1.3.6.1.4.1.18.3.5.1.4.10.1.39 |
wfCctOptsCngcQp3CngLvl2ThresholdDefines priority 3 queue congestion level 2 threshold as a
percentage of priority 3 queue threshold.
The value of this attribute should be greater than
wfCctOptsCngcQp3CngLvl1Threshold, otherwise there will be no
priority 3 queue congestion level 2.rw INTEGER .1.3.6.1.4.1.18.3.5.1.4.10.1.40 |
wfCctOptsCngcPriority0TxPktsNumber of priority 0 packets transmittedro Counter .1.3.6.1.4.1.18.3.5.1.4.10.1.41 |
wfCctOptsCngcPriority0TxOctetsNumber of priority 0 Octets transmittedro Counter .1.3.6.1.4.1.18.3.5.1.4.10.1.42 |
wfCctOptsCngcPriority0DropPktsNumber of priority 0 packets dropped */ro Counter .1.3.6.1.4.1.18.3.5.1.4.10.1.43 |
wfCctOptsCngcPriority0DropOctetsNumber of priority 0 octets droppedro Counter .1.3.6.1.4.1.18.3.5.1.4.10.1.44 |
wfCctOptsCngcPriority1TxPktsNumber of priority 1 packets transmittedro Counter .1.3.6.1.4.1.18.3.5.1.4.10.1.45 |
wfCctOptsCngcPriority1TxOctetsNumber of priority 1 Octets transmittedro Counter .1.3.6.1.4.1.18.3.5.1.4.10.1.46 |
wfCctOptsCngcPriority1DropPktsNumber of priority 1 packets dropped */ro Counter .1.3.6.1.4.1.18.3.5.1.4.10.1.47 |
wfCctOptsCngcPriority1DropOctetsNumber of priority 1 octets droppedro Counter .1.3.6.1.4.1.18.3.5.1.4.10.1.48 |
wfCctOptsCngcPriority2TxPktsNumber of priority 2 packets transmittedro Counter .1.3.6.1.4.1.18.3.5.1.4.10.1.49 |
wfCctOptsCngcPriority2TxOctetsNumber of priority 2 Octets transmittedro Counter .1.3.6.1.4.1.18.3.5.1.4.10.1.50 |
wfCctOptsCngcPriority2DropPktsNumber of priority 2 packets dropped */ro Counter .1.3.6.1.4.1.18.3.5.1.4.10.1.51 |
wfCctOptsCngcPriority2DropOctetsNumber of priority 2 octets droppedro Counter .1.3.6.1.4.1.18.3.5.1.4.10.1.52 |
wfCctOptsCngcPriority3TxPktsNumber of priority 3 packets transmittedro Counter .1.3.6.1.4.1.18.3.5.1.4.10.1.53 |
wfCctOptsCngcPriority3TxOctetsNumber of priority 3 Octets transmittedro Counter .1.3.6.1.4.1.18.3.5.1.4.10.1.54 |
wfCctOptsCngcPriority3DropPktsNumber of priority 3 packets dropped */ro Counter .1.3.6.1.4.1.18.3.5.1.4.10.1.55 |
wfCctOptsCngcPriority3DropOctetsNumber of priority 3 octets droppedro Counter .1.3.6.1.4.1.18.3.5.1.4.10.1.56 |
wfCctOptsCngcTxFRNonDePktsNumber of Frame Relay non DE packets transmittedro Counter .1.3.6.1.4.1.18.3.5.1.4.10.1.57 |
wfCctOptsCngcTxFRNonDeOctetsNumber of Frame Relay non DE octets transmittedro Counter .1.3.6.1.4.1.18.3.5.1.4.10.1.58 |
wfCctOptsCngcTxFRDePktsNumber of Frame Relay DE packets transmittedro Counter .1.3.6.1.4.1.18.3.5.1.4.10.1.59 |
wfCctOptsCngcTxFRDeOctetsNumber of Frame Relay DE octets transmittedro Counter .1.3.6.1.4.1.18.3.5.1.4.10.1.60 |
wfCctOptsCngcDropFRNonDePktsNumber of Frame Relay non DE packets droppedro Counter .1.3.6.1.4.1.18.3.5.1.4.10.1.61 |
wfCctOptsCngcDropFRNonDeOctetsnumber of Frame Relay non DE octets droppedro Counter .1.3.6.1.4.1.18.3.5.1.4.10.1.62 |
wfCctOptsCngcDropFRDePktsnumber of Frame Relay DE packets droppedro Counter .1.3.6.1.4.1.18.3.5.1.4.10.1.63 |
wfCctOptsCngcDropFRDeOctetsnumber of Frame Relay DE octets droppedro Counter .1.3.6.1.4.1.18.3.5.1.4.10.1.64 |
wfCctOptsCngcFRSetFecnPktsnumber of Frame Relay packets in which this link set FECNro Counter .1.3.6.1.4.1.18.3.5.1.4.10.1.65 |
wfCctOptsCngcFRSetFecnOctetsnumber of Frame Relay octets in which this link set FECNro Counter .1.3.6.1.4.1.18.3.5.1.4.10.1.66 |
wfCctOptsCngcFRSetBecnPktsnumber of Frame Relay frames in which this link set BECNro Counter .1.3.6.1.4.1.18.3.5.1.4.10.1.67 |
wfCctOptsCngcFRSetBecnOctetsnumber of Frame Relay octets in which this link set BECNro Counter .1.3.6.1.4.1.18.3.5.1.4.10.1.68 |
wfCctOptsCngcDropNonFRPktsNumber of Non Frame Relay packets droppedro Counter .1.3.6.1.4.1.18.3.5.1.4.10.1.69 |
wfCctOptsCngcDropNonFROctetsnumber of Non Frame Relay octets droppedro Counter .1.3.6.1.4.1.18.3.5.1.4.10.1.70 |
wfCctOptsCngcLogPowerThis number specifies that the following log events:
1. Dropped DE Frame.
2. Dropped Non DE Frames.
3. Set DE Frames.
4. Set FECN/BECN.
be logged once every (X) occurances. Where (X) = Base 2
raised to the power. The user specifies the power by setting
this wfCctOptsCngcLogPower mib attribute.
For example, setting wfCctOptsCngcLogPower to a value of 10 means
that a log message will be logged once every 1024 occurances.
1024 = (2 ^ wfCctOptsCngcLogPower) or (2 raised to 10th power).
Legal values for this attribute ranges from 10 to 31. This translates
to 2^10 (1024) through 2^31 (2147483648). Default: 2^31.rw INTEGER .1.3.6.1.4.1.18.3.5.1.4.10.1.71 |
wfSwservTODTableSWSERV circuit time of day MIB SEQUENCE OF WfSwservTODEntry .1.3.6.1.4.1.18.3.5.1.4.11 |
wfSwservTODEntryAn entry in the wfSwservTODTable WfSwservTODEntry .1.3.6.1.4.1.18.3.5.1.4.11.1 |
wfSwservTODDeleteDelete time of day instance from the list for this circuitrw Enumeration .1.3.6.1.4.1.18.3.5.1.4.11.1.1 |
wfSwservTODCctCCT number for time of day instancero INTEGER .1.3.6.1.4.1.18.3.5.1.4.11.1.2 |
wfSwservTODIndexa unique number to specify instancero INTEGER .1.3.6.1.4.1.18.3.5.1.4.11.1.3 |
wfSwservTODTypeType of TOD Configurationrw Enumeration .1.3.6.1.4.1.18.3.5.1.4.11.1.4 |
wfSwservTODStartTimeStart Time of day allow a line to dial ( HHMM format )rw INTEGER .1.3.6.1.4.1.18.3.5.1.4.11.1.5 |
wfSwservTODEndTimeEnd Time of day connection can be active for
specified circuit ( HHMM format )rw INTEGER .1.3.6.1.4.1.18.3.5.1.4.11.1.6 |
wfSwservTODInactivityEnableInactivity Timer if disabled the inactivity timer is ignored during this
time period, if enabled the connection is brought down due to
inactivity. If this parameter is DISABLED, the circuit will be
established automatically during the configured times,
regardless of the Availability Mode.rw Enumeration .1.3.6.1.4.1.18.3.5.1.4.11.1.7 |
wfSwservTODAvailabilityModeSet this field to AVAILABLE to allow the circuit to be
established between the configured start and end times.
Set it to NOT AVAILABLE to prevent the circuit from
being established during those times.
Inactivity Timeout must be ENABLED for Availability Mode
to have any effect. If Inactivity Timeout is DISABLED, the
circuit will be established automatically during the
configured times, regardless of the Availability Mode.rw Enumeration .1.3.6.1.4.1.18.3.5.1.4.11.1.8 |
wfSwservTODStandbyFailBackModeIndicates if failback mode for this time of day range. When set to
automatic circuit will failback subject to the failback timer. When
set to manual circuit will not failback.rw Enumeration .1.3.6.1.4.1.18.3.5.1.4.11.1.9 |
wfSwservTODStandbyFailBackTimeIndicates number of minutes to wait after the primary is observed
as active before deactivating the standby. Default value of 0
disables failback timer.rw INTEGER .1.3.6.1.4.1.18.3.5.1.4.11.1.10 |
wfDemandCctGrpTableThe table of demand circuits groups defined over switched services SEQUENCE OF WfDemandCctGrpEntry .1.3.6.1.4.1.18.3.5.1.4.12 |
wfDemandCctGrpEntryEntry format for the table of demand circuit group options WfDemandCctGrpEntry .1.3.6.1.4.1.18.3.5.1.4.12.1 |
wfDmdCctGroupDeleteCreation and deletion flagrw Enumeration .1.3.6.1.4.1.18.3.5.1.4.12.1.1 |
wfDmdCctGroupNumCircuit Numberro INTEGER .1.3.6.1.4.1.18.3.5.1.4.12.1.2 |
wfDmdCctGroupPoolIdDemand pool id used by this demand circuit groupro INTEGER .1.3.6.1.4.1.18.3.5.1.4.12.1.3 |
wfDmdCctGroupNumofCctsDemand pool id used by this demand circuit grouprw INTEGER .1.3.6.1.4.1.18.3.5.1.4.12.1.4 |
wfDmdCctGroupIPEnableIP unnumbered enabled or disabled for specified demand circuit grouprw Enumeration .1.3.6.1.4.1.18.3.5.1.4.12.1.5 |
wfDmdCctGroupIPUnnumAssocThe associated IP address used by unnumbered demand circuit group
every demand circuit in this demand circuit group uses the same
associated IP address.rw IpAddress .1.3.6.1.4.1.18.3.5.1.4.12.1.6 |
wfDmdCctGroupRIPEnableRIP enabled or disabled for specified demand circuit grouprw Enumeration .1.3.6.1.4.1.18.3.5.1.4.12.1.7 |
wfDmdCctGroupOSPFEnableOSPF enabled or disabled for specified demand circuit grouprw Enumeration .1.3.6.1.4.1.18.3.5.1.4.12.1.8 |
wfDmdCctGroupIPXEnableIPX unnumbered enabled or disabled for specified demand circuit grouprw Enumeration .1.3.6.1.4.1.18.3.5.1.4.12.1.9 |
wfDmdCctGroupBridgeEnableBridge enabled or disabled for specified demand circuit grouprw Enumeration .1.3.6.1.4.1.18.3.5.1.4.12.1.10 |
wfDmdCctGroupCctListList of demand circuits that are members of this grouprw OCTET STRING .1.3.6.1.4.1.18.3.5.1.4.12.1.11 |
wfDmdCctGroupIPXRoutingIPX routing protocol used for specified demand circuit grouprw Enumeration .1.3.6.1.4.1.18.3.5.1.4.12.1.12 |
wfDmdCctGroupIPXWANEnableIPXWAN enabled or disabled for specified demand circuit grouprw Enumeration .1.3.6.1.4.1.18.3.5.1.4.12.1.13 |
wfDmdCctGroupRadiusEnableRadius enabled or disabled for specified demand circuit grouprw Enumeration .1.3.6.1.4.1.18.3.5.1.4.12.1.14 |