Wellfleet-BISYNC-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for Wellfleet-BISYNC-MIB.
48
Objects
Active
Status
3
Dependencies
Imported Objects
Objects
48 total| Object Name |
|---|
RFC1155-SMI* BISYNC line record * SEQUENCE OF WfBisyncEntry .1.3.6.1.4.1.18.3.4.27.1 |
wfBisyncEntryAn entry in the BISYNC table WfBisyncEntry .wfBisyncTable.1 |
wfBisyncDeleteCreate/Delete parameterrw Enumeration .wfBisyncTable.1.1 |
wfBisyncDisableEnable/Disable parameterrw Enumeration .wfBisyncTable.1.2 |
wfBisyncCctCCT number for this line instancerw INTEGER .wfBisyncTable.1.3 |
wfBisyncMtuMTU parameter, this is buffer size for BISYNC media, fixedrw INTEGER .wfBisyncTable.1.4 |
wfBisyncMediaTypeMedia type selection is provided via this parameterrw Enumeration .wfBisyncTable.1.5 |
wfBisyncCableTypeType of Cable attached to the Bisync port - this is
needed for V.25bis and Raise DTR to properly
communicate with the modemrw Enumeration .wfBisyncTable.1.6 |
wfBisyncClkSourceTx/Rx clock source is either internally or external generated.rw Enumeration .wfBisyncTable.1.7 |
wfBisyncClkSpeedTx/Rx clock speed. This speed selection is valid when either
internal or external clocking is selected. In some cases, router
software uses this attribute for route selection. If Priority
Queuing is configured, it chooses queue depths based on this
attribute. If internal clocking is selected, this attribute
effects hardware initialization. If external
clocking is selected, this attribute should be set to the speed that
most closely corresponds to the speed of the external clock.rw Enumeration .wfBisyncTable.1.8 |
wfBisyncServiceService Type selection is provided via this parameter. The
supported services can be selected per interface.rw Enumeration .wfBisyncTable.1.9 |
wfBisyncCfgTxQueueLengthConfigured Transmit Queue Length. Values other than zero
over-ride the router selected values. A value of zero has a
special meaning. Zero causes router based default values to
be used. Values larger than the compiled ring size are
truncated to the compiled ring size.rw INTEGER .wfBisyncTable.1.10 |
wfBisyncCfgRxQueueLengthConfigured Receive Queue Length. Values other than zero
over-ride the router selected values. A value of zero has
a special meaning. Zero causes router based default values
to be used. Values larger than the compiled ring size are
truncated to the compiled ring size.rw INTEGER .wfBisyncTable.1.11 |
wfBisyncCharModeControl Character Mode - ASCII/EBCDICrw Enumeration .wfBisyncTable.1.12 |
wfBisyncLineNumberline number for this line instancerw INTEGER .wfBisyncTable.1.13 |
wfBisyncRtsEnableThe RTS parameter enables/disables detection of RTS signals on the
interface. Normal default mode is running without RTS enabledrw Enumeration .wfBisyncTable.1.14 |
wfBisyncExternalClkSpeedExternal Clock Speed. If external clocking is configured, this
attribute should be set to the clock speed of the externally
supplied clock. Depending on the protocols configured in the
interface, this value may control internal decision making in the
router. In soe cases, router software uses this attribute for route
selection. If Priority Queueing is configured, it chooses queue depths
based on this attribute. This attribute has no effect when Internal
Clocking is configured.rw INTEGER .wfBisyncTable.1.15 |
wfBisyncModuleModule number for ASN platform, filled in by driver. For non-ASN
platforms, this attribute will not be usedro Enumeration .wfBisyncTable.1.16 |
wfBisyncActualConnectorActual Connector Number for ASN platform, filled in by driver.
For non-ASN platforms, this attribute will not be used.ro Enumeration .wfBisyncTable.1.17 |
wfBisyncConnectorInstance ID Connector, filled in by driver. For the ASN
this attribute is an encoded value and is equal to
'module'*10 + 'connector'. Where 'module' is defined in
attribute mm and 'connector' is defined in attribute cc
of this table. For non-ASN platforms this attribute is
the physical connector number on the slot.ro Enumeration .wfBisyncTable.1.18 |
wfBisyncSlotInstance ID Slot, filled in by driverro INTEGER .wfBisyncTable.1.19 |
wfBisyncActiveCctActive CCT number for this line instancero INTEGER .wfBisyncTable.1.20 |
wfBisyncStateLine Driver state variable, Not Present, DSR Wait,
Init, Down, Upro Enumeration .wfBisyncTable.1.21 |
wfBisyncLastStateThe state which the driver was in prior to the most recent re-initiali-
zation.ro Enumeration .wfBisyncTable.1.22 |
wfBisyncRxOctetsNumber of octets received without errorro Counter .wfBisyncTable.1.23 |
wfBisyncTxOctetsNumber of octets transmitted without errorro Counter .wfBisyncTable.1.24 |
wfBisyncRxFramesNumber of frames received without errorro Counter .wfBisyncTable.1.25 |
wfBisyncTxFramesNumber of frames transmitted without errorro Counter .wfBisyncTable.1.26 |
wfBisyncRxErrorsNumber of receive errorsro Counter .wfBisyncTable.1.27 |
wfBisyncTxErrorsNumber of transmission errorsro Counter .wfBisyncTable.1.28 |
wfBisyncTxLackRescsNumber of frames clipped in driver's transmit routine due to transmit
congestion.ro Counter .wfBisyncTable.1.29 |
wfBisyncTxUnderFlowsNumber of transmission underflows, device FIFO went empty before
next DMA request was granted.ro Counter .wfBisyncTable.1.30 |
wfBisyncRxOverFlowsNumber of receive overflows, device FIFO overflowed before next
DMA cycle granted. No buffer resources available.ro Counter .wfBisyncTable.1.31 |
wfBisyncRxBadFramesNumber of bad receive frames, caused by FCS errors or
non octet aligned.ro Counter .wfBisyncTable.1.32 |
wfBisyncRxRuntsNumber of runt frames receivedro Counter .wfBisyncTable.1.33 |
wfBisyncTxQueueLengthCurrent Transmit Queue Length.ro INTEGER .wfBisyncTable.1.34 |
wfBisyncRxQueueLengthCurrent Receive Queue Length.ro INTEGER .wfBisyncTable.1.35 |
wfBisyncRxReplenMissesNumber of packet buffer misses while attempting to replenish driver
receive ring.ro Counter .wfBisyncTable.1.36 |
wfBisyncLastChangeThe value of the SysUptime at the time the interface entered it's current
operational state (UP state). SysUpTime is defined as the time (in
hundredths of a second) since the network management portion of the system
was last re-initialized. Usually the time since boot.ro TimeTicks (SNMPv2-SMI) .wfBisyncTable.1.37 |
wfBisyncOutQLenThe instantaneous current length of the output packet queuero Gauge .wfBisyncTable.1.38 |
wfBisyncRxLackRescsCharNumber of Rx characters dropped due to lack of buffer resourcesro Counter .wfBisyncTable.1.39 |
wfBisyncIsrBCZeroNumber of interrupts with byte count zeroro Counter .wfBisyncTable.1.40 |
wfBisyncIsrBCSixNumber of interrupts with byte count six or morero Counter .wfBisyncTable.1.41 |
wfBisyncIsrBCInvalidNumber of interrupts with an unexpected message bytero Counter .wfBisyncTable.1.42 |
wfBisyncIsrBCErrorsNumber of interrupt errorsro Counter .wfBisyncTable.1.43 |
wfBisyncLocalConnectionStateThe state of the cable at the router end.ro Enumeration .wfBisyncTable.1.44 |
wfBisyncRemoteConnectionStateThe state of the cable at the controller end.ro Enumeration .wfBisyncTable.1.45 |
wfBisyncAdditionalSyncPairsThe number of pairs of sync characters, in addition to the first pair, to send between frames.rw INTEGER .wfBisyncTable.1.46 |