HUAWEI-BTEST-MIB
AI MIB Summary
The HUAWEI-BTEST-MIB module enables SNMP-based monitoring of Huawei broadband testing subsystems, exposing performance metrics and status indicators for active line quality and throughput validation procedures. It facilitates the retrieval of test session states, error counters, and signal integrity data required for diagnosing broadband access network anomalies.
This MIB is used for defining Huawei's BTEST MIB objects,which is used for Broad test.
Main OID:
hwBTest.1.3.6.1.4.1.2011.6.21.3
120
Objects
Active
Status
7
Dependencies
Imported Objects
Objects
120 total| Object Name |
|---|
hwTest OBJECT IDENTIFIER .1.3.6.1.4.1.2011.6.21 |
hwBTestThis MIB is used for defining Huawei's BTEST MIB objects,which
is used for Broad test. MODULE-IDENTITY .1.3.6.1.4.1.2011.6.21.3 |
hwBTestMib OBJECT IDENTIFIER .1.3.6.1.4.1.2011.6.21.3.1 |
hwBTestMIBObjects OBJECT IDENTIFIER .1.3.6.1.4.1.2011.6.21.3.1.1 |
hwBTSSxDslLineCfgTableThe hwBTSSxDslLineCfgTable table describes xDSL line configuration.
This table is used for bandwidth test.
The index of this table is ifIndex. SEQUENCE OF HwBTSSxDslLineCfgEntry .1.3.6.1.4.1.2011.6.21.3.1.1.1 |
hwBTSSxDslLineCfgEntryThe hwBTSSxDslLineCfgTable table describes xDSL line configuration.
This table is used for bandwidth test.
The index of this entry is ifIndex. HwBTSSxDslLineCfgEntry .1.3.6.1.4.1.2011.6.21.3.1.1.1.1 |
hwBTSSxDslLineOverlapTypeOverlap mode of xDSL with PSTN line.
Options:
1. overLap(1) - xDSL overlap with POTS line
2. direct(2) - There is no pots line, no splitter, no phone
3. unknown(3) - The mode is unknown
Default: unknown(3)rw HWBTSSxDslLineOverLap .1.3.6.1.4.1.2011.6.21.3.1.1.1.1.1 |
hwBTSSCoTestTablexDSL central office emulational measurement table.The table is used for xDSL central emulational measurement.
The index of this table is ifIndex. SEQUENCE OF HwBTSSCoTestEntry .1.3.6.1.4.1.2011.6.21.3.1.1.2 |
hwBTSSCoTestEntryxDSL central office emulational measurement table.The table is used for xDSL central emulational measurement.
The index of this entry is ifIndex. HwBTSSCoTestEntry .1.3.6.1.4.1.2011.6.21.3.1.1.2.1 |
hwBTSSCoOperTypeCO emulational operation type.
Options:
1. stop(1) - Stop CO emulational
2. start(2) - Start CO emulationalrw Enumeration .1.3.6.1.4.1.2011.6.21.3.1.1.2.1.1 |
hwBTSSCoTestResultCO emulational test result.
Options:
1. normal(1) - The test of CO emulational is successful
2. testfail(2) - Fail in test of CO emulationalro Enumeration .1.3.6.1.4.1.2011.6.21.3.1.1.2.1.2 |
hwBTSSCoTestBusyFlagCO force test flag
Options:
1. busyNoTest(1) - No test on busy
2. busyTest(2) - Test on busy
3. busystrenTest(3) - Forced test on busyrw Enumeration .1.3.6.1.4.1.2011.6.21.3.1.1.2.1.3 |
hwBTSSAuxPortCfgTableConfiguration table of the broadband test auxiliary port
This table is used to configure a certain type of emulation port required in the CO emulation test.
The indexes of this table are hwTestGroupNo and hwBTSSAuxPortType. SEQUENCE OF HwBTSSAuxPortCfgEntry .1.3.6.1.4.1.2011.6.21.3.1.1.17 |
hwBTSSAuxPortCfgEntryConfiguration table of the broadband test auxiliary port
This table is used to configure a certain type of emulation port required in the CO emulation test.
The indexes of this entry are hwTestGroupNo and hwBTSSAuxPortType. HwBTSSAuxPortCfgEntry .1.3.6.1.4.1.2011.6.21.3.1.1.17.1 |
hwBTSSAuxPortTypeAssistance port type of BTSS.
Options:
1. adsl(1) - Assistance port type of BTSS is adsl
2. vdsl(2) - Assistance port type of BTSS is vdsl
3. gshdsl(3) - Assistance port type of BTSS is gshdsl Enumeration .1.3.6.1.4.1.2011.6.21.3.1.1.17.1.1 |
hwBTSSAuxPortIfIndexAssistance port ifIndex of BTSS.rw Integer32 .1.3.6.1.4.1.2011.6.21.3.1.1.17.1.2 |
hwBTSSAuxPortRowStatusRow status(add(4),delete(6)).rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2011.6.21.3.1.1.17.1.3 |
hwBTSSTestedPortOperTableThis table describes operation for tested port.
The index of this table is ifIndex. SEQUENCE OF HwBTSSTestedPortOperEntry .1.3.6.1.4.1.2011.6.21.3.1.1.18 |
hwBTSSTestedPortOperEntryThis table describes operation for tested port.
The index of this entry is ifIndex. HwBTSSTestedPortOperEntry .1.3.6.1.4.1.2011.6.21.3.1.1.18.1 |
hwBTSSTestedPortOperTypeOperation type of BTSS tested port.
Options:
1. capture(1) - Capture
2. release(2) - Release
3. startmonitor(3) - Start monitor
4. stopmonitor(4) - Stop monitor
5. resumeport(5) - Resume port
6. invalid(-1) - Invalid valuerw Enumeration .1.3.6.1.4.1.2011.6.21.3.1.1.18.1.1 |
hwBTSSTestedPortOperModeOperation mode of BTSS tested port.
Options:
1. inline(1) - BTSS tested port in test
2. outline(2) - BTSS tested port out test
3. monitor(3) - Monitoring BTSS tested port
4. both(4) - Capture for circuit and loop-line test
5. meltNoCutxDSL(5) - Capture for melt chip test with co and cpe connecting
6. meltForceCutxDSL(6) - Capture for melt chip test with co and cpe disconnecting
7. testLineLoopback(7) - Capture for test line loopback
8. internalResistorLoopback(8) - Capture for internal resistor loopback
9. passthroughmode(9) - No capture
Default: passthroughmode(9)rw Enumeration .1.3.6.1.4.1.2011.6.21.3.1.1.18.1.2 |
hwBTSSTestedPortOperResultTest result of BTSS tested port.
Options:
1. normal(1) - The test of BTSS tested port is successful
2. fail(2) - Fail in test of BTSS tested port
3. timeout(4) - The test of BTSS tested port is timeoutro Enumeration .1.3.6.1.4.1.2011.6.21.3.1.1.18.1.3 |
hwBTSSTestedPortTestBusyFlagTested port force test.
Options:
1. busyNoTest(1) - No test on busy
2. busyTest(2) - Test on busy
3. busystrenTest(3) - Forced test on busyrw Enumeration .1.3.6.1.4.1.2011.6.21.3.1.1.18.1.4 |
hwBTSSTestedPortTestPOTSFlagTested port POTS service flag
Options:
1. noCutPOTS(1) - No cut off POTS
2. busyNoTest(2) - No test on POTS busy (Cut off POTS)
3. busyTest(3) - Test on POTS busy (Cut off POTS)
4. busystrenTest(4) - Forced test on POTS busy (Cut off POTS)rw Enumeration .1.3.6.1.4.1.2011.6.21.3.1.1.18.1.5 |
hwBTSSCqtTransTestTableThis table describes CQT test by transparent command.
The index of this table is ifIndex. SEQUENCE OF HwBTSSCqtTransTestEntry .1.3.6.1.4.1.2011.6.21.3.1.1.19 |
hwBTSSCqtTransTestEntryThis table describes CQT test by transparent command.
The index of this entry is ifIndex. HwBTSSCqtTransTestEntry .1.3.6.1.4.1.2011.6.21.3.1.1.19.1 |
hwBTSSCqtTransTestOperTypeCQT transparent Operation type
Options:
1. stop(1) - Stop CQT transparent test
2. start(2) - Start CQT transparent testrw Enumeration .1.3.6.1.4.1.2011.6.21.3.1.1.19.1.1 |
hwBTSSCqtTransTestCRCModeCRC Operation type of CQT transparent.
Options:
1. disable(1) - Disable CQT transparent
2. enable(2) - Enable CQT transparent
Default: disable(1)rw Enumeration .1.3.6.1.4.1.2011.6.21.3.1.1.19.1.2 |
hwBTSSCqtTransTestOperResultCQT transparent Operation result.
Options:
1. normal(1) - The CQT transparent test is successful
2. fail(2) - The CQT transparent test fails
3. abort(3) - The CQT transparent test aborts
4. powerfeed(4) - The CQT transparent test power feedsro Enumeration .1.3.6.1.4.1.2011.6.21.3.1.1.19.1.3 |
hwBTSSCqtTransTestTxCmdSending command string in TL1 format.rw OCTET STRING .1.3.6.1.4.1.2011.6.21.3.1.1.19.1.4 |
hwBTSSCqtTransTestResultNoTest result No.
Range: 1-255ro Integer32 .1.3.6.1.4.1.2011.6.21.3.1.1.19.1.5 |
hwBTSSCqtTransTestResultLastFlagLast package flag for test result.
Options:
1. false(0) - This is not the last package
2. true(1) - The last packagero Enumeration .1.3.6.1.4.1.2011.6.21.3.1.1.19.1.6 |
hwBTSSCqtTransTestResultCQT transparent Test result.ro OCTET STRING .1.3.6.1.4.1.2011.6.21.3.1.1.19.1.7 |
hwBTSSMultiFrameMiscOperTableThis table describes test relatived operation for multi-frame.
The index of this table is ifIndex. SEQUENCE OF HwBTSSMultiFrameMiscOperEntry .1.3.6.1.4.1.2011.6.21.3.1.1.20 |
hwBTSSMultiFrameMiscOperEntryThis table describes test relatived operation for multi-frame.
The index of this entry is ifIndex. HwBTSSMultiFrameMiscOperEntry .1.3.6.1.4.1.2011.6.21.3.1.1.20.1 |
hwBTSSMultiFrameMiscCleanTestClean current test on specified frame.
Options:
1. start(1) - Start clean current testrw Enumeration .1.3.6.1.4.1.2011.6.21.3.1.1.20.1.1 |
hwBTSSMultiFrameMiscTestedFrameTested frame of BTSS multi-frame.
Default: 0rw Integer32 .1.3.6.1.4.1.2011.6.21.3.1.1.20.1.2 |
hwBTSSMultiFrameMiscTestedPortTypeTested port type of BTSS multi-frame.rw HWPortType (HUAWEI-TC-MIB) .1.3.6.1.4.1.2011.6.21.3.1.1.20.1.3 |
hwBTSSMultiFrameMiscTestedLineTypeTested line type of BTSS multi-frame.rw HWBTSSxDslLineOverLap .1.3.6.1.4.1.2011.6.21.3.1.1.20.1.4 |
hwBTSSAdslSeltTestTableThis table describes selt test for adsl2+.
The index of this table is ifIndex. SEQUENCE OF HWBTSSAdslSeltTestEntry .1.3.6.1.4.1.2011.6.21.3.1.1.21 |
hwBTSSAdslSeltTestEntryThis table describes selt test for adsl2+.
The index of this entry is ifIndex. HWBTSSAdslSeltTestEntry .1.3.6.1.4.1.2011.6.21.3.1.1.21.1 |
hwBTSSAdslSeltTestOperTypeSelt test operation type.
Options:
1. stop(1) - Stop selt test of BTSS
2. start(2) - Start selt test of BTSS
3. invalid(-1) - No operationrw Enumeration .1.3.6.1.4.1.2011.6.21.3.1.1.21.1.1 |
hwBTSSAdslSeltTestOperResultSelt test operation result.
Options:
1. normal(1) - Selt test of BTSS is successful
2. fail(2) - Fail in selt test of BTSS
3. abort(3) - Selt test of BTSS abortsro Enumeration .1.3.6.1.4.1.2011.6.21.3.1.1.21.1.2 |
hwBTSSAdslSeltTestResultNoSelt test result serial number.
Range: 1-255ro Integer32 .1.3.6.1.4.1.2011.6.21.3.1.1.21.1.3 |
hwBTSSAdslSeltTestResultLastFlagLast package flag of test.
Options:
1. false(0) - This is not the last package
2. true(1) - The last packagero Enumeration .1.3.6.1.4.1.2011.6.21.3.1.1.21.1.4 |
hwBTSSAdslSeltTestResultSelt test result data.ro OCTET STRING .1.3.6.1.4.1.2011.6.21.3.1.1.21.1.5 |
hwBTSSAdslSeltTestParamLoopLengthSelt test parameter Loop Length.
The invalid value is -1. If no SELT is performed, no SELT data is
generated because the SELT is incomplete, or no SELT data can be
obtained from the port because the SELT data is aged and cleared,
the invalid value will be returned.ro Integer32 .1.3.6.1.4.1.2011.6.21.3.1.1.21.1.6 |
hwBTSSAdslSeltTestParamLoopTerminSelt test parameter Loop Termination state.
Options:
1. open(0) - Indicates that the line terminal is started
2. short(1) - Indicates that the line terminal is short-circuited
3. unknow(2) - Indicates the unknown state
4. terminated(3) - Indicates that the line terminal is stopped
5. invalid(-1) - Indicates the invalid statero Enumeration .1.3.6.1.4.1.2011.6.21.3.1.1.21.1.7 |
hwBTSSAdslSeltTestParamLoopGaugeSelt test parameter Loop Gauge.
Options:
1. greater26awg(1) - Indicates that the line gauge is greater than 26
2. equal26awg(2) - Indicates that the line gauge is 26
3. equal24awg(3) - Indicates that the line gauge is 24
4. less24awg(4) - Indicates that the line gauge is smaller than 24
5. unknowawg(5) - Indicates an unknown line gauge.
6. invalid(-1) - Indicates an invalid value.rw Enumeration .1.3.6.1.4.1.2011.6.21.3.1.1.21.1.8 |
hwBTSSAdslSeltTestParamUpShnCapSelt test parameter Upstream Shannon Capacity.
The invalid value is -1. If no SELT is performed, no SELT data is
generated because the SELT is incomplete, or no SELT data can be
obtained from the port because the SELT data is aged and cleared,
the invalid value will be returned.ro Integer32 .1.3.6.1.4.1.2011.6.21.3.1.1.21.1.9 |
hwBTSSAdslSeltTestParamDwnShnCapSelt test parameter Downstream Shannon Capacity.ro Integer32 .1.3.6.1.4.1.2011.6.21.3.1.1.21.1.10 |
hwBTSSAdslSeltTestParamInbandNoiseSelt test parameter Inband Noise
512 values that indicate inband noise in dBm/Hz,
covering ADSL, ADSL2, and ADSL2+ bands, from 0 to 2.2 MHz.ro OCTET STRING .1.3.6.1.4.1.2011.6.21.3.1.1.21.1.11 |
hwBTSSAdslSeltTestParamTerminRespSelt test parameter Termination Response
180 values that indicate termination response magnitude from 0 to 18 kft.ro OCTET STRING .1.3.6.1.4.1.2011.6.21.3.1.1.21.1.12 |
hwBTSSAdslSeltTestParamUpMgnAtRateSelt test parameter Upstream Ratevs. Margin.
This value is a measure of the quality of your upstream data
signal relative to the noise on the line. Hundreds of values that
indicate SNR margin in DB/Hz at a particular bit rate are provided,
at a certain increments, up to 30 Mbps. This information may be plotted
with the bit rate on the X-axis and the SNR margin on the Y-axis.ro OCTET STRING .1.3.6.1.4.1.2011.6.21.3.1.1.21.1.13 |
hwBTSSAdslSeltTestParamDwnMgnAtRateSelt test parameter Downstream Rate vs. Margin.
This value is a measure of the quality of your downstream data
signal relative to the noise on the line. Hundreds of values that
indicate SNR margin in DB/Hz at a particular bit rate are provided,
at a certain increments, up to 30 Mbps. This information may be plotted
with the bit rate on the X-axis and the SNR margin on the Y-axis.ro OCTET STRING .1.3.6.1.4.1.2011.6.21.3.1.1.21.1.14 |
hwBTSSAdslSeltTestParamUpRateAtMgnSelt test parameter Upstream Margin vs. Rate.ro OCTET STRING .1.3.6.1.4.1.2011.6.21.3.1.1.21.1.15 |
hwBTSSAdslSeltTestParamDwnRateAtMgnSelt test parameter Downstream Margin vs. Rate.ro OCTET STRING .1.3.6.1.4.1.2011.6.21.3.1.1.21.1.16 |
hwBTSSAdslSeltTestParamLoopAttenAtFreqSelt test parameter loop attenuation versus frequency.
Every four bytes constitute the result of a tone.
This information may be plotted with the bit frequency
on the X-axis and the loop attenuation on the Y-axis.ro OCTET STRING .1.3.6.1.4.1.2011.6.21.3.1.1.21.1.17 |
hwBTSSAdslSeltTestParamUnCalibLineScaleThe uncalibrated echo response, UER(i* UER_G*Df), shall be represented in linear format by a
scale factor and a normalized complex number a(i)+j*b(i), where i is a frequency index i ranging
from 0 to NSC-1, the subcarrier spacing, Df = 4.3125 kHz, and (NSC-1) * UER_G * Df is the
highest frequency supported by the SELT-PMD functionality. The UER granularity parameter,
UER_G, has two valid values: 1 and 2, indicating whether the measurements were performed using
a tone spacing of 4.3125 kHz or of 8.625 kHz. If the uncalibrated echo response is being reported
over a frequency range of 17.664 MHz or lower, UER_G shall be set to 1. If the uncalibrated echo
response is being reported over a frequency range that is greater than 17.664 MHz, UER_G shall be
set to 2.
The scale factor shall be coded as a 32-bit unsigned integer. Both a(i) and b(i) shall be coded as
32-bit 2's complement signed integers. The value of UER(i* UER_G*Df) shall be defined as:
UER(i* UER_G*Df) = (scale/2^31)*(a(i)+j*b(i))/2^31. In order to maximize precision, the scale factor
shall be chosen such that max(|a(i)|, |b(i)|) over all i is equal to 2^31-1.
NOTE - This data format supports an UER(f) granularity of 2^-31 and an UER(f) dynamic range of
approximately +6 dB to -186 dB, however it does not imply any future accuracy requirements.
An UER(i*UER_G* Df) value indicated as a(i) = b(i) = -2^31 is a special value. It indicates that no
measurement could be done for this subcarrier either because it is not supported by the SELT-PMD
function, or that the value is out of range to be represented.ro Unsigned32 .1.3.6.1.4.1.2011.6.21.3.1.1.21.1.18 |
hwBTSSAdslSeltTestParamUnCalibEchoRespRealThe uncalibrated echo response, UER(i* UER_G*Df), shall be represented in linear format by a
scale factor and a normalized complex number a(i)+j*b(i), where i is a frequency index i ranging
from 0 to NSC-1, the subcarrier spacing, Df = 4.3125 kHz, and (NSC-1) * UER_G * Df is the
highest frequency supported by the SELT-PMD functionality. The UER granularity parameter,
UER_G, has two valid values: 1 and 2, indicating whether the measurements were performed using
a tone spacing of 4.3125 kHz or of 8.625 kHz. If the uncalibrated echo response is being reported
over a frequency range of 17.664 MHz or lower, UER_G shall be set to 1. If the uncalibrated echo
response is being reported over a frequency range that is greater than 17.664 MHz, UER_G shall be
set to 2.
The scale factor shall be coded as a 32-bit unsigned integer. Both a(i) and b(i) shall be coded as
32-bit 2's complement signed integers. The value of UER(i* UER_G*Df) shall be defined as:
UER(i* UER_G*Df) = (scale/2^31)*(a(i)+j*b(i))/2^31. In order to maximize precision, the scale factor
shall be chosen such that max(|a(i)|, |b(i)|) over all i is equal to 2^31-1.
NOTE - This data format supports an UER(f) granularity of 2^-31 and an UER(f) dynamic range of
approximately +6 dB to -186 dB, however it does not imply any future accuracy requirements.
An UER(i*UER_G* Df) value indicated as a(i) = b(i) = -2^31 is a special value. It indicates that no
measurement could be done for this subcarrier either because it is not supported by the SELT-PMD
function, or that the value is out of range to be represented.ro OCTET STRING .1.3.6.1.4.1.2011.6.21.3.1.1.21.1.19 |
hwBTSSAdslSeltTestParamUnCalibEchoRespImgThe uncalibrated echo response, UER(i* UER_G*Df), shall be represented in linear format by a
scale factor and a normalized complex number a(i)+j*b(i), where i is a frequency index i ranging
from 0 to NSC-1, the subcarrier spacing, Df = 4.3125 kHz, and (NSC-1) * UER_G * Df is the
highest frequency supported by the SELT-PMD functionality. The UER granularity parameter,
UER_G, has two valid values: 1 and 2, indicating whether the measurements were performed using
a tone spacing of 4.3125 kHz or of 8.625 kHz. If the uncalibrated echo response is being reported
over a frequency range of 17.664 MHz or lower, UER_G shall be set to 1. If the uncalibrated echo
response is being reported over a frequency range that is greater than 17.664 MHz, UER_G shall be
set to 2.
The scale factor shall be coded as a 32-bit unsigned integer. Both a(i) and b(i) shall be coded as
32-bit 2's complement signed integers. The value of UER(i* UER_G*Df) shall be defined as:
UER(i* UER_G*Df) = (scale/2^31)*(a(i)+j*b(i))/2^31. In order to maximize precision, the scale factor
shall be chosen such that max(|a(i)|, |b(i)|) over all i is equal to 2^31-1.
NOTE - This data format supports an UER(f) granularity of 2^-31 and an UER(f) dynamic range of
approximately +6 dB to -186 dB, however it does not imply any future accuracy requirements.
An UER(i*UER_G* Df) value indicated as a(i) = b(i) = -2^31 is a special value. It indicates that no
measurement could be done for this subcarrier either because it is not supported by the SELT-PMD
function, or that the value is out of range to be represented.ro OCTET STRING .1.3.6.1.4.1.2011.6.21.3.1.1.21.1.20 |
hwBTSSAdslSeltTestParamCalibLineScaleThe scale factor of calibrated echo response shall be coded as a 16 bit
unsigned integer.ro Unsigned32 .1.3.6.1.4.1.2011.6.21.3.1.1.21.1.21 |
hwBTSSAdslSeltTestParamCalibEchoRespRealThe calibrated echo response UER(i* f), shall be represented
in linear format by a scale factor and a normalized complex number a(i)+j*b(i),
where i is the subcarrier index i ranging from 0 to NSC-1 and Df = 4.3125kHz
and (NSC-1) * Df is the highest frequency supported by the SELT-PMD functionality.
The scale factor shall be coded as a 16 bit unsigned integer.
Both a(i) and b(i) shall be coded as a 16 bit 2's complement signed integer.
The value of UER(i* f) shall be defined as UER(i* f) = (scale/215)*(a(i)+j*b(i))/215.
In order to maximize precision, the scale factor shall be chosen such that max(|a(i)|, |b(i)|)
over all i is equal to 215-1. This data format supports an UER(f) granularity of 2-15
and an UER(f) dynamic range of approximately +6 dB to -90 dB.
An UER(i*Df) value indicated as a(i) = b(i) = -215 is a special value.
It indicates that no measurement could be done for this subcarrier because
it is out of the PSD mask passband or that the value is out of range to be represented.ro OCTET STRING .1.3.6.1.4.1.2011.6.21.3.1.1.21.1.22 |
hwBTSSAdslSeltTestParamCalibEchoRespImgThe calibrated echo response UER(i* f), shall be represented
in linear format by a scale factor and a normalized complex number a(i)+j*b(i),
where i is the subcarrier index i ranging from 0 to NSC-1 and Df = 4.3125kHz
and (NSC-1) * Df is the highest frequency supported by the SELT-PMD functionality.
The scale factor shall be coded as a 16 bit unsigned integer.
Both a(i) and b(i) shall be coded as a 16 bit 2's complement signed integer.
The value of UER(i* f) shall be defined as UER(i* f) = (scale/215)*(a(i)+j*b(i))/215.
In order to maximize precision, the scale factor shall be chosen such that max(|a(i)|, |b(i)|)
over all i is equal to 215-1. This data format supports an UER(f) granularity of 2-15
and an UER(f) dynamic range of approximately +6 dB to -90 dB.
An UER(i*Df) value indicated as a(i) = b(i) = -215 is a special value.
It indicates that no measurement could be done for this subcarrier because
it is out of the PSD mask passband or that the value is out of range to be represented.ro OCTET STRING .1.3.6.1.4.1.2011.6.21.3.1.1.21.1.23 |
hwBTSSAdslSeltTestParamVarUerCThe relative variance of the uncalibrated echo response REL_VAR_UER(i* UER_G *Df) shall be
represented as an 8-bit unsigned integer v(i), where i is the subcarrier index i = 0 to NSC-1. The
value of REL_VAR_UER(i* UER_G *Df) shall be defined as REL_VAR_UER(i* UER_G *Df) = 3 - v(i)/2 dB.
The number v(i) is an 8-bit unsigned integer in the range 0 to 254.
This data format supports a REL_VAR_UER(i) over a range from -124 dB to +3 dB for each carrier with a granularity from 0.5 dB.
Out of range values shall be clamped to the closest range bound.
The special value v(i) = 255 indicates that no measurement is available for that carrier.
Unit: 0.5dBro OCTET STRING .1.3.6.1.4.1.2011.6.21.3.1.1.21.1.24 |
hwBTSSAdslSeltTestParamUerMmdCThis parameter is the maximum allowed time for SELT uncalibrated echo response measurement,
between the time of the start command written by the SELT-PMD-ME, and the time the result is
available for read operation by SELT-PMD-ME.
It is configurable between 5 seconds and 240 seconds, in steps of 1 second.
The invalid value is 255. If data on the port cannot be queried, the invalid value will be returned.
Unit: 1 secondrw Unsigned32 .1.3.6.1.4.1.2011.6.21.3.1.1.21.1.25 |
hwBTSSAdslSeltTestParamQlnMmdCThis parameter is the maximum allowed time for SELT quiet line noise measurement, between the
time of the start command written by the SELT-PMD-ME, and the time the result is available for
read operation by SELT-PMD-ME.
It is configurable between 1 second and 240 seconds, in steps of 1 second.
The invalid value is 255. If data on the port cannot be queried, the invalid value will be returned.
Unit: 1 secondrw Unsigned32 .1.3.6.1.4.1.2011.6.21.3.1.1.21.1.26 |
hwBTSSAdslSeltTestParamUmeCThis parameter is a binary variable.
Options:
1.enable(1) - Enable UER capture switch
2.disable(2) - Disable UER capture switch
3.invalid(-1) - Invalid valuerw Enumeration .1.3.6.1.4.1.2011.6.21.3.1.1.21.1.27 |
hwBTSSAdslSeltTestParamQmeCThis parameter is a binary variable.
Options:
1.enable(1) - Enable QLN capture switch
2.disable(2) - Disable QLN capture switch
3.invalid(-1) - Invalid valuerw Enumeration .1.3.6.1.4.1.2011.6.21.3.1.1.21.1.28 |
hwBTSSAdslSeltTestParamUerStatusUerStatus.
Options:
1.off(1) - The status is off.
2.running(2) - The status is running.
3.completed(3) - The status is completed.
4.failed(4) - The status is failed.ro Enumeration .1.3.6.1.4.1.2011.6.21.3.1.1.21.1.29 |
hwBTSSAdslSeltTestParamQlnStatusQlnStatus.
Options:
1.off(1) - The status is off.
2.running(2) - The status is running.
3.completed(3) - The status is completed.
4.failed(4) - The status is failed.ro Enumeration .1.3.6.1.4.1.2011.6.21.3.1.1.21.1.30 |
hwBTSSAdslSeltTestParamCalcEnableThe status of calculation switch.
Options:
1. enable(1) - Enable calculation switch
2. disable(2) - Disable calculation switch
3. invalid(-1) - Invalid value
Default: enable(1)rw Enumeration .1.3.6.1.4.1.2011.6.21.3.1.1.21.1.31 |
hwBTSSAdslSeltTestParamAttnAt180KHZSelt test parameter attenuation at 180KHZ.
It ranges from -1100 to 0 units of 0.1dB(physical values
are -110 to 0 dB).
The invalid value is -1. If no SELT is performed, no SELT data is
generated because the SELT is incomplete, or no SELT data can be
obtained from the port because the SELT data is aged and cleared,
the invalid value will be returned.
Unit: 0.1dBro Integer32 UNITS "0.1dB" .1.3.6.1.4.1.2011.6.21.3.1.1.21.1.65535 |
hwBTSSAdslSeltTestParamAttnAt300KHZSelt test parameter attenuation at 300KHZ.
It ranges from -1100 to 0 units of 0.1dB(physical values
are -110 to 0 dB).
The invalid value is -1. If no SELT is performed, no SELT data is
generated because the SELT is incomplete, or no SELT data can be
obtained from the port because the SELT data is aged and cleared,
the invalid value will be returned.
Unit: 0.1dBro Integer32 UNITS "0.1dB" .1.3.6.1.4.1.2011.6.21.3.1.1.21.1.65536 |
hwBTSSAdslSeltTestParamQSPsdValueThe SELT quiet line noise provides the quiet line noise PSD as measured by the SELT-PMD
function (see clause A.1.1.2) for each sub-carrier frequency i * SELTQLN_G * Df where i ranges
from 0 to NSC-1, Df = 4.3125 kHz, and (NSC-1) * SELTQLN_G * Df is the highest frequency
supported by the SELT-PMD functionality. SELTQLN_G has two valid values: 1 and 2, indicating
whether the measurements were performed using a tone spacing of 4.3125 kHz or of 8.625 kHz. If
the SELT quiet line noise is being reported over a frequency range of 17.664 MHz or lower,
SELTQLN_G shall be set to 1. If the SELT quiet line noise is being reported over a frequency
range that is greater than 17.664 MHz, SELTQLN_G shall be set to 2.
SELT quiet line noise SELTQLN(i * SELTQLN_G * Df) shall be represented as an 8-bit unsigned
integer n(i), where i is the subcarrier index i = 0 to NSC-1. The value of
SELTQLN(i * SELTQLN_G * Df) shall be defined as SELTQLN(i * SELTQLN_G * Df ) =
-23 - (n(i)/2) dBm/Hz. This data format supports a SELTQLN(f) granularity of 0.5 dB and an
SELTQLN(f) dynamic range of -150 to -23 dBm/Hz.
Unit: 0.5dBm/Hzro OCTET STRING .1.3.6.1.4.1.2011.6.21.3.1.1.21.1.65537 |
hwBTSSAdslDeltTestTableThis table describes Delt test for adsl2+.
The index of this table is ifIndex. SEQUENCE OF HWBTSSAdslDeltTestEntry .1.3.6.1.4.1.2011.6.21.3.1.1.22 |
hwBTSSAdslDeltTestEntryThis table describes Delt test for adsl2+.
The index of this entry is ifIndex. HWBTSSAdslDeltTestEntry .1.3.6.1.4.1.2011.6.21.3.1.1.22.1 |
hwBTSSAdslDeltTestOperTypeDelt test operation type.
Options:
1. stop(1) - Delt test stop
2. start(2) - Start delt test
3. invalid(-1) - No operationrw Enumeration .1.3.6.1.4.1.2011.6.21.3.1.1.22.1.1 |
hwBTSSAdslDeltTestOperResultDelt test operation result.
Options:
1. normal(1) - Delt test is normal
2. fail(2) - Fail in delt test
3. abort(3) - Delt test abortsro Enumeration .1.3.6.1.4.1.2011.6.21.3.1.1.22.1.2 |
hwBTSSAdslDeltTestResultNoDelt test result serial number.
Range: 1-255ro Integer32 .1.3.6.1.4.1.2011.6.21.3.1.1.22.1.3 |
hwBTSSAdslDeltTestResultLastFlagLast package flag for test result.
Options:
1. false(0) - This is not the last package
2. true(1) - The last packagero Enumeration .1.3.6.1.4.1.2011.6.21.3.1.1.22.1.4 |
hwBTSSAdslDeltTestResultDelt test result data.ro OCTET STRING .1.3.6.1.4.1.2011.6.21.3.1.1.22.1.5 |
hwBTSSLoopLineToneOprTableThe table hwBTSSLoopLineToneOprTable is used to Loop Line Tone.
The index of this table is ifIndex. SEQUENCE OF HwBTSSLoopLineToneOprEntry .1.3.6.1.4.1.2011.6.21.3.1.1.23 |
hwBTSSLoopLineToneOprEntryThe table hwBTSSLoopLineToneOprTable is used to Loop Line Tone.
The index of this entry is ifIndex. HwBTSSLoopLineToneOprEntry .1.3.6.1.4.1.2011.6.21.3.1.1.23.1 |
hwBTSSLoopLineToneOprTypeOperation type of BTSS loop line tone
Options:
1. check(1) - Indicates that checking the signal tone is started
2. send(2) - Indicates that sending the signal tone is started
3. stopsend(3) - Indicates that stopping sending the signal tone is startedrw Enumeration .1.3.6.1.4.1.2011.6.21.3.1.1.23.1.1 |
hwBTSSLoopLineToneIntensityTone intensity of BTSS loop line tone.
Options:
1. fivedB(1) - Tone intensity of BTSS is five dB
2. tendB(2) - Tone intensity of BTSS is ten dB
3. fifteendB(3) - Tone intensity of BTSS is fifteen dBrw Enumeration .1.3.6.1.4.1.2011.6.21.3.1.1.23.1.2 |
hwBTSSLoopLineToneBusyFlagTested port force test of BTSS loop line tone.
Options:
1. busyNoTest(1) - No test on busy
2. busyTest(2) - Test on busy
3. busystrenTest(3) - Forced test on busyrw Enumeration .1.3.6.1.4.1.2011.6.21.3.1.1.23.1.3 |
hwBTSSLoopLineToneResultOperate result of BTSS loop line tone.
Options:
1. succeed(1) - The test of BTSS loop line tone is successful
2. failed(2) - Failed in BTSS loop line tone testro Enumeration .1.3.6.1.4.1.2011.6.21.3.1.1.23.1.4 |
hwBTSSSeltAuxPortCfgTableThis table sets assistance port for SELT.
The index of this table is hwBTSSSeltAuxedPortIfIndex. SEQUENCE OF HwBTSSSeltAuxPortCfgEntry .1.3.6.1.4.1.2011.6.21.3.1.1.24 |
hwBTSSSeltAuxPortCfgEntryThis table sets assistance port for SELT.
The index of this entry is hwBTSSSeltAuxedPortIfIndex. HwBTSSSeltAuxPortCfgEntry .1.3.6.1.4.1.2011.6.21.3.1.1.24.1 |
hwBTSSSeltAuxedPortIfIndexThe ifindex of the Auxed port. If there is only one global Auxed port,
the value is 65535. Integer32 .1.3.6.1.4.1.2011.6.21.3.1.1.24.1.1 |
hwBTSSSeltAuxPortIfIndexAssistance port ifIndexrw Integer32 .1.3.6.1.4.1.2011.6.21.3.1.1.24.1.2 |
hwBTSSSeltAuxPortRowStatusRow status(add(4), delete(6)) of the Aux port.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2011.6.21.3.1.1.24.1.3 |
hwBTSSAdslSeltLevelTableThis table supports the configuration of adsl selt level.
The indexes of this table are hwFrameIndex and hwSlotIndex. SEQUENCE OF HwBTSSAdslSeltLevelEntry .1.3.6.1.4.1.2011.6.21.3.1.1.25 |
hwBTSSAdslSeltLevelEntryThis table supports the configuration of adsl selt level.
The indexes of this entry are hwFrameIndex and hwSlotIndex. HwBTSSAdslSeltLevelEntry .1.3.6.1.4.1.2011.6.21.3.1.1.25.1 |
hwBTSSAdslSeltLevelThe level of adsl SELT:
1 Level0;
2 Level1;
3 Level2;
4 Level3.
A special value of -1 indicates the level of adsl SELT is invalid.rw Integer32 (-1 | 1..4) .1.3.6.1.4.1.2011.6.21.3.1.1.25.1.1 |
hwBTSSAdslSeltCalibrationTableThis table describes calibration data of selt test.
The index of this table is ifIndex. SEQUENCE OF HWBTSSAdslSeltCalibrationtEntry .1.3.6.1.4.1.2011.6.21.3.1.1.26 |
hwBTSSAdslSeltCalibrationEntryThis table describes calibration data of selt test.
The index of this entry is ifIndex. HWBTSSAdslSeltCalibrationtEntry .1.3.6.1.4.1.2011.6.21.3.1.1.26.1 |
hwBTSSAdslSeltCalibrationInvVendorIdIt consists of 8 binary octets, including a
provider code.ro OCTET STRING .1.3.6.1.4.1.2011.6.21.3.1.1.26.1.1 |
hwBTSSAdslSeltCalibrationDataSegment1The part 1 of selt calibration data.
The unit of selt calibration data is 0.00001.ro OCTET STRING .1.3.6.1.4.1.2011.6.21.3.1.1.26.1.2 |
hwBTSSAdslSeltCalibrationDataSegment2The part 2 of selt calibration data.
The unit of selt calibration data is 0.00001.ro OCTET STRING .1.3.6.1.4.1.2011.6.21.3.1.1.26.1.3 |
hwBTestTraps OBJECT IDENTIFIER .1.3.6.1.4.1.2011.6.21.3.2 |
hwBTestTrapVbOids OBJECT IDENTIFIER .1.3.6.1.4.1.2011.6.21.3.2.1 |
hwBTestVbOidsReason OBJECT IDENTIFIER .1.3.6.1.4.1.2011.6.21.3.2.1.2 |
hwBTSSCqtOfflineReasonCqt module offline reason.
Options:
1. commFail(1) - CQT module communication fail. Resolving method:Check CQT module running normal
2. userReset(2) - User reset commandro Enumeration .1.3.6.1.4.1.2011.6.21.3.2.1.2.1 |
hwBTSSRequestIDNMS request ID.ro Integer32 .1.3.6.1.4.1.2011.6.21.3.2.1.2.2 |
hwBTestAlarmTraps OBJECT IDENTIFIER .1.3.6.1.4.1.2011.6.21.3.2.2 |
hwBTestAlarmTrapsOIDs OBJECT IDENTIFIER .1.3.6.1.4.1.2011.6.21.3.2.2.0 |
hwBTSSCqtOnlineTrapCQT unit online status trap.
This notification indicates alarm when CQT unit online.
enumFirst:
explain: CQT module communication OK
resolving method:NA. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.6.21.3.2.2.0.1 |
hwBTSSCqtOfflineTrapCQT unit offline status trap.
This notification indicates alarm when CQT unit offline. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.6.21.3.2.2.0.2 |
hwBTestGeneralTraps OBJECT IDENTIFIER .1.3.6.1.4.1.2011.6.21.3.2.3 |
hwBTestGeneralTrapsOIDs OBJECT IDENTIFIER .1.3.6.1.4.1.2011.6.21.3.2.3.0 |
hwBTSSCoStartTrapStart Co test trap.
This notification indicates alarm when starting Co test. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.6.21.3.2.3.0.1 |
hwBTSSCoStopTrapStop Co test trap.
This notification indicates alarm when stopping Co test. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.6.21.3.2.3.0.2 |
hwBTSSTestedPortOperTrapTested port operation trap.
This notification indicates alarm when tested port operation. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.6.21.3.2.3.0.3 |
hwBTSSCqtTransTestOperResultTrapCqt transparent test trap.
This notification indicates alarm when starting or stoping Cqt transparent test. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.6.21.3.2.3.0.4 |
hwBTSSCqtTransTestResultTrapCqt transparent test trap.
This notification indicates alarm when reporting the result after Cqt transparent test. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.6.21.3.2.3.0.5 |
hwBTSSLoopLineToneOperTraploop line tone test result trap: 1:hwBTSSLoopLineToneResult.
This notification indicates alarm when reporting the test result of Loop Line Tone. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.6.21.3.2.3.0.6 |
hwBTSSCaptureTrapBTSS capture trap.
This trap is sent when BTSS capture result reported. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.6.21.3.2.3.0.7 |
hwBTSSDeltResultDataTrapBTSS delt result trap.
This notification indicates alarm when captures result data of BTSS delt test. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.6.21.3.2.3.0.8 |