HUAWEI-ADSL-MIB
AI MIB Summary
The HUAWEI-ADSL-MIB defines the managed objects required to monitor and configure ADSL line parameters, physical layer statistics, and session states on Huawei DSL Access Multiplexer (DSLAM) and modem hardware via SNMP. It enables the collection of critical performance metrics such as line attenuation, signal-to-noise ratio, and error counters to facilitate fault isolation and bandwidth management for broadband access networks.
This MIB is used for defining Huawei's ADSL management MIB objects.
Main OID:
hwAdsl.1.3.6.1.4.1.2011.6.31
378
Objects
Active
Status
13
Dependencies
Imported Objects
Objects
378 total| Object Name |
|---|
hwadslLineExtConfProfileThe value of this object identifies the row
in the ADSL Extend Line Configuration Profile Table,
(adslLineExtConfProfileTable), which applies to this
ADSL line, and channels if applicable.
NULL - indicates that there is no extend line profile
bound to this port.
Range: 0-32rw OCTET STRING .1.3.6.1.2.1.10.94.1.1.1.1.65536 |
hwadslLineDynamicProfileThe value of this object identifies the row
in the ADSL Dynamic Profile Table,which applies to this
ADSL line, and channels if applicable.
NULL - indicates that there is no Dynamic profile
bound to this port.
Range: 0-32rw OCTET STRING .1.3.6.1.2.1.10.94.1.1.1.1.65537 |
hwAdslAtucCurrTransModeA set of ADSL line transmission modes.ro HWADSLTRANSMISSIONMODETYPE .1.3.6.1.2.1.10.94.1.1.2.1.65536 |
hwAdslAtucCurrSignalAtnCurrent signal attenuation of the ATU-C, indicating the difference between the transmit signal of the ATU-R and the receive signal of the ATU-C.
Range: 0-630
Unit: tenth dBro Gauge32 .1.3.6.1.2.1.10.94.1.1.2.1.65537 |
hwadslAturTransmissionCapabilitiesThe ATU transmission system capability list of the different
coding types. It is coded in a bit-map representation with 1
or more bits set. A bit set to '1' means that the ATU
supports the respective coding. The value may be derived
from the handshaking procedures defined in G.994.1.ro Adsl2TransmissionModeType (ADSL2-LINE-TC-MIB) .1.3.6.1.2.1.10.94.1.1.3.1.65535 |
hwAdslAturCurrSignalAtnThe signal attenuation value on ATUR: It indicates the difference between the transmit signal of the ATU-C and the receive signal of the ATU-R.
Range: 0-630
Unit: tenth dBro Gauge32 .1.3.6.1.2.1.10.94.1.1.3.1.65536 |
hwadslAtucChanCurrINPIndicates Impulse Noise Protection on downstream direction.
The value multiply 1/10000 is the real value.
Unit: DMT Symbolro Gauge32 UNITS "DMT Symbol" .1.3.6.1.2.1.10.94.1.1.4.1.65536 |
hwadslAtucChanRsSymbolsIndicates Reed-Solomon symbols on downstream direction.
The value multiply 1/10000 is the real value.
Unit: bytero Gauge32 UNITS "byte" .1.3.6.1.2.1.10.94.1.1.4.1.65537 |
hwadslAtucChanRsRedundancyIndicates Reed-Solomon redundancy on downstream direction.
Unit: bytero Gauge32 UNITS "byte" .1.3.6.1.2.1.10.94.1.1.4.1.65538 |
hwadslAtucChanRsDepthIndicates Reed-Solomon depth on downstream direction.
Unit: bytero Gauge32 UNITS "byte" .1.3.6.1.2.1.10.94.1.1.4.1.65539 |
hwadslAtucChanSymbolLengthIndicates the Bit Number of the DMT Symbol on downstream direction.
Unit: bitro Gauge32 UNITS "bit" .1.3.6.1.2.1.10.94.1.1.4.1.65540 |
hwadslAtucChanPhyRrrcBitsThe bits in the channel that used to retransmission on downstream direction.ro Gauge32 .1.3.6.1.2.1.10.94.1.1.4.1.65541 |
hwadslAtucChanPhyRtxQueueQueues in send buffer on downstream direction.ro Gauge32 .1.3.6.1.2.1.10.94.1.1.4.1.65542 |
hwadslAtucChanRsSizeIndicates Reed-Solomon Codeword Size on downstream direction .
Range: 0-255
Unit: bytero Gauge32 UNITS "byte" .1.3.6.1.2.1.10.94.1.1.4.1.65543 |
hwadslAtucChanCodeGainIndicates Code Gain on downstream direction.
It ranges from 0 to 16 units of 0.5 dB (physical values
are 0 to 8 dB).ro Gauge32 .1.3.6.1.2.1.10.94.1.1.4.1.65544 |
hwadslAtucChanPcbIndicates Power Cut-back on downstream direction.
It ranges from 0 to 400 units of 0.1 dB(physical values
are 0 to 40 dB).
Unit: tenth dBro Gauge32 UNITS "tenth dB" .1.3.6.1.2.1.10.94.1.1.4.1.65545 |
hwadslAturChanCurrINPIndicates Impulse Noise Protection on upstream direction.
The value multiply 1/10000 is the real value.
Unit: DMT Symbolro Gauge32 UNITS "DMT Symbol" .1.3.6.1.2.1.10.94.1.1.5.1.65536 |
hwadslAturChanRsSymbolsIndicates Reed-Solomon symbols on upstream direction.
The value multiply 1/10000 is the real value.
Unit: bytero Gauge32 UNITS "byte" .1.3.6.1.2.1.10.94.1.1.5.1.65537 |
hwadslAturChanRsRedundancyIndicates Reed-Solomon redundancy on upstream direction.
Unit: bytero Gauge32 UNITS "byte" .1.3.6.1.2.1.10.94.1.1.5.1.65538 |
hwadslAturChanRsDepthIndicates Reed-Solomon depth on upstream direction.
Unit: bytero Gauge32 UNITS "byte" .1.3.6.1.2.1.10.94.1.1.5.1.65539 |
hwadslAturChanSymbolLengthIndicates the Bit Number of the DMT Symbol on upstream direction.
Unit: bitro Gauge32 UNITS "bit" .1.3.6.1.2.1.10.94.1.1.5.1.65540 |
hwadslAturChanPhyRrrcBitsThe bits in the channel that used to retransmission on upstream direction.ro Gauge32 .1.3.6.1.2.1.10.94.1.1.5.1.65541 |
hwadslAturChanPhyRtxQueueQueues in send buffer on upstream direction.ro Gauge32 .1.3.6.1.2.1.10.94.1.1.5.1.65542 |
hwadslAturChanRsSizeIndicates Reed-Solomon Codeword Size on upstream direction.
Range: 0-255
Unit: bytero Gauge32 UNITS "byte" .1.3.6.1.2.1.10.94.1.1.5.1.65543 |
hwadslAturChanCodeGainIndicates Code Gain on upstream direction.
It ranges from 0 to 16 units of 0.5 dB (physical values
are 0 to 8 dB).ro Gauge32 .1.3.6.1.2.1.10.94.1.1.5.1.65544 |
hwAdslAtucPerfFailFullInitsCount of the line initialization failed attempts since agent reset.ro Counter32 .1.3.6.1.2.1.10.94.1.1.6.1.65535 |
hwAdslAtucPerfCurr15MinFailFullInitsCount of the line initialization failed attempts in the current 15 minute interval.ro Counter32 .1.3.6.1.2.1.10.94.1.1.6.1.65536 |
hwAdslAtucPerfCurr1DayFailFullInitsCount of the line initialization failed attempts in the day as measured by adslAtucPerfCurr1DayTimeElapsed.ro Counter32 .1.3.6.1.2.1.10.94.1.1.6.1.65537 |
hwAdslAtucPerfPrev1DayFailFullInitsCount of the line initialization failed attempts in the most recent previous 1-day period.ro Counter32 .1.3.6.1.2.1.10.94.1.1.6.1.65538 |
hwAdslAtucIntervalFailFullInitsCount of the line initialization failed attempts during the interval.ro Counter32 .1.3.6.1.2.1.10.94.1.1.8.1.65535 |
hwadslAtucChanFecBlksCount of all blocks received with FEC anomalies
since agent reset.ro Counter32 .1.3.6.1.2.1.10.94.1.1.10.1.65536 |
hwadslAtucChanHecBlksCount of all blocks received with HEC anomalies
since agent reset.ro Counter32 .1.3.6.1.2.1.10.94.1.1.10.1.65537 |
hwadslAtucChanCrcBlksCount of all blocks received with CRC anomalies
since agent reset.ro Counter32 .1.3.6.1.2.1.10.94.1.1.10.1.65538 |
hwadslAtucChanPerfCurr15MinFecBlksCount of all blocks received with FEC anomalies
on this channel within the current 15 minute
interval.ro Counter32 .1.3.6.1.2.1.10.94.1.1.10.1.65539 |
hwadslAtucChanPerfCurr15MinHecBlksCount of all blocks received with HEC anomalies
on this channel within the current 15 minute
interval.ro Counter32 .1.3.6.1.2.1.10.94.1.1.10.1.65540 |
hwadslAtucChanPerfCurr15MinCrcBlksCount of all blocks received with CRC anomalies
on this channel within the current 15 minute
interval.ro Counter32 .1.3.6.1.2.1.10.94.1.1.10.1.65541 |
hwadslAtucChanPerfCurr1DayFecBlksCount of all blocks received with FEC anomalies
on this channel during the current day as
measured by adslAtucChanPerfCurr1DayTimeElapsed.ro Counter32 .1.3.6.1.2.1.10.94.1.1.10.1.65542 |
hwadslAtucChanPerfCurr1DayHecBlksCount of all blocks received with HEC anomalies
on this channel during the current day as
measured by adslAtucChanPerfCurr1DayTimeElapsed.ro Counter32 .1.3.6.1.2.1.10.94.1.1.10.1.65543 |
hwadslAtucChanPerfCurr1DayCrcBlksCount of all blocks received with CRC anomalies
on this channel during the current day as
measured by adslAtucChanPerfCurr1DayTimeElapsed.ro Counter32 .1.3.6.1.2.1.10.94.1.1.10.1.65544 |
hwadslAtucChanPerfPrev1DayFecBlksCount of all blocks received with FEC anomalies
on this channel within the most recent previous
1-day period.ro Counter32 .1.3.6.1.2.1.10.94.1.1.10.1.65545 |
hwadslAtucChanPerfPrev1DayHecBlksCount of all blocks received with HEC anomalies
on this channel within the most recent previous
1-day period.ro Counter32 .1.3.6.1.2.1.10.94.1.1.10.1.65546 |
hwadslAtucChanPerfPrev1DayCrcBlksCount of all blocks received with CRC anomalies
on this channel within the most recent previous
1-day period.ro Counter32 .1.3.6.1.2.1.10.94.1.1.10.1.65547 |
hwadslAtucChanRtxCWCount of units request retransmission since agent reset.ro Gauge32 .1.3.6.1.2.1.10.94.1.1.10.1.65548 |
hwadslAtucChanRtxCorrectedCWCount of units corrected by retransmission since agent reset.ro Gauge32 .1.3.6.1.2.1.10.94.1.1.10.1.65549 |
hwadslAtucChanRtxUncorrectedCWCount of units uncorrected by retransmission since agent reset.ro Gauge32 .1.3.6.1.2.1.10.94.1.1.10.1.65550 |
hwadslAtucChanPerfCurr15MinRtxCWCount of units request retransmission on this
channel within the current 15 minute interval.ro Gauge32 .1.3.6.1.2.1.10.94.1.1.10.1.65551 |
hwadslAtucChanPerfCurr15MinRtxCorrectedCWCount of units corrected by retransmission on this
channel within the current 15 minute interval.ro Gauge32 .1.3.6.1.2.1.10.94.1.1.10.1.65552 |
hwadslAtucChanPerfCurr15MinRtxUncorrectedCWCount of units uncorrected by retransmission on
this channel within the current 15 minute interval.ro Gauge32 .1.3.6.1.2.1.10.94.1.1.10.1.65553 |
hwadslAtucChanPerfCurr1DayRtxCWCount of units request retransmission on
this channel during the current day.ro Gauge32 .1.3.6.1.2.1.10.94.1.1.10.1.65554 |
hwadslAtucChanPerfCurr1DayRtxCorrectedCWCount of units corrected by retransmission
on this channel during the current day.ro Gauge32 .1.3.6.1.2.1.10.94.1.1.10.1.65555 |
hwadslAtucChanPerfCurr1DayRtxUncorrectedCWCount of units uncorrected by retransmission
on this channel during the current day.ro Gauge32 .1.3.6.1.2.1.10.94.1.1.10.1.65556 |
hwadslAtucChanPerfPrev1DayRtxCWCount of units request retransmission on this channel
within the most recent previous 1-day period.ro Gauge32 .1.3.6.1.2.1.10.94.1.1.10.1.65557 |
hwadslAtucChanPerfPrev1DayRtxCorrectedCWCount of units corrected by retransmission on this
channel within the most recent previous 1-day period.ro Gauge32 .1.3.6.1.2.1.10.94.1.1.10.1.65558 |
hwadslAtucChanPerfPrev1DayRtxUncorrectedCWCount of units uncorrected by retransmission on this
channel within the most recent previous 1-day period.ro Gauge32 .1.3.6.1.2.1.10.94.1.1.10.1.65559 |
hwadslAturChanFecBlksCount of all blocks received with FEC anomalies
since agent reset.ro Counter32 .1.3.6.1.2.1.10.94.1.1.11.1.65536 |
hwadslAturChanHecBlksCount of all blocks received with HEC anomalies
since agent reset.ro Counter32 .1.3.6.1.2.1.10.94.1.1.11.1.65537 |
hwadslAturChanCrcBlksCount of all blocks received with CRC anomalies
since agent reset.ro Counter32 .1.3.6.1.2.1.10.94.1.1.11.1.65538 |
hwadslAturChanPerfCurr15MinFecBlksCount of all blocks received with FEC anomalies
on this channel within the current 15 minute
interval.ro Counter32 .1.3.6.1.2.1.10.94.1.1.11.1.65539 |
hwadslAturChanPerfCurr15MinHecBlksCount of all blocks received with HEC anomalies
on this channel within the current 15 minute
interval.ro Counter32 .1.3.6.1.2.1.10.94.1.1.11.1.65540 |
hwadslAturChanPerfCurr15MinCrcBlksCount of all blocks received with CRC anomalies
on this channel within the current 15 minute
interval.ro Counter32 .1.3.6.1.2.1.10.94.1.1.11.1.65541 |
hwadslAturChanPerfCurr1DayFecBlksCount of all blocks received with FEC anomalies
on this channel during the current day as
measured by adslAturChanPerfCurr1DayTimeElapsed.ro Counter32 .1.3.6.1.2.1.10.94.1.1.11.1.65542 |
hwadslAturChanPerfCurr1DayHecBlksCount of all blocks received with HEC anomalies
on this channel during the current day as
measured by adslAturChanPerfCurr1DayTimeElapsed.ro Counter32 .1.3.6.1.2.1.10.94.1.1.11.1.65543 |
hwadslAturChanPerfCurr1DayCrcBlksCount of all blocks received with CRC anomalies
on this channel during the current day as
measured by adslAturChanPerfCurr1DayTimeElapsed.ro Counter32 .1.3.6.1.2.1.10.94.1.1.11.1.65544 |
hwadslAturChanPerfPrev1DayFecBlksCount of all blocks received with FEC anomalies
on this channel within the most recent previous
1-day period.ro Counter32 .1.3.6.1.2.1.10.94.1.1.11.1.65545 |
hwadslAturChanPerfPrev1DayHecBlksCount of all blocks received with HEC anomalies
on this channel within the most recent previous
1-day period.ro Counter32 .1.3.6.1.2.1.10.94.1.1.11.1.65546 |
hwadslAturChanPerfPrev1DayCrcBlksCount of all blocks received with CRC anomalies
on this channel within the most recent previous
1-day period.ro Counter32 .1.3.6.1.2.1.10.94.1.1.11.1.65547 |
hwadslAturChanRtxCWCount of units request retransmission since agent reset.ro Gauge32 .1.3.6.1.2.1.10.94.1.1.11.1.65548 |
hwadslAturChanRtxCorrectedCWCount of units corrected by retransmission since agent reset.ro Gauge32 .1.3.6.1.2.1.10.94.1.1.11.1.65549 |
hwadslAturChanRtxUncorrectedCWCount of units uncorrected by retransmission since agent reset.ro Gauge32 .1.3.6.1.2.1.10.94.1.1.11.1.65550 |
hwadslAturChanPerfCurr15MinRtxCWCount of units request retransmission on this
channel within the current 15 minute interval.ro Gauge32 .1.3.6.1.2.1.10.94.1.1.11.1.65551 |
hwadslAturChanPerfCurr15MinRtxCorrectedCWCount of units corrected by retransmission on
this channel within the current 15 minute interval.ro Gauge32 .1.3.6.1.2.1.10.94.1.1.11.1.65552 |
hwadslAturChanPerfCurr15MinRtxUncorrectedCWCount of units uncorrected by retransmission on
this channel within the current 15 minute interval.ro Gauge32 .1.3.6.1.2.1.10.94.1.1.11.1.65553 |
hwadslAturChanPerfCurr1DayRtxCWCount of units request retransmission on
this channel during the current day.ro Gauge32 .1.3.6.1.2.1.10.94.1.1.11.1.65554 |
hwadslAturChanPerfCurr1DayRtxCorrectedCWCount of units corrected by retransmission
on this channel during the current day.ro Gauge32 .1.3.6.1.2.1.10.94.1.1.11.1.65555 |
hwadslAturChanPerfCurr1DayRtxUncorrectedCWCount of units uncorrected by retransmission
on this channel during the current day.ro Gauge32 .1.3.6.1.2.1.10.94.1.1.11.1.65556 |
hwadslAturChanPerfPrev1DayRtxCWCount of units request retransmission on this
channel within the most recent previous 1-day period.ro Gauge32 .1.3.6.1.2.1.10.94.1.1.11.1.65557 |
hwadslAturChanPerfPrev1DayRtxCorrectedCWCount of units corrected by retransmission on this
channel within the most recent previous 1-day period.ro Gauge32 .1.3.6.1.2.1.10.94.1.1.11.1.65558 |
hwadslAturChanPerfPrev1DayRtxUncorrectedCWCount of units uncorrected by retransmission on this
channel within the most recent previous 1-day period.ro Gauge32 .1.3.6.1.2.1.10.94.1.1.11.1.65559 |
hwadslAtucChanIntervalFecBlksCount of all blocks received with FRC anomalies
on this channel during this interval.ro PerfIntervalCount (PerfHist-TC-MIB) .1.3.6.1.2.1.10.94.1.1.12.1.65536 |
hwadslAtucChanIntervalHecBlksCount of all blocks received with HRC anomalies
on this channel during this interval.ro PerfIntervalCount (PerfHist-TC-MIB) .1.3.6.1.2.1.10.94.1.1.12.1.65537 |
hwadslAtucChanIntervalCrcBlksCount of all blocks received with CRC anomalies
on this channel during this interval.ro PerfIntervalCount (PerfHist-TC-MIB) .1.3.6.1.2.1.10.94.1.1.12.1.65538 |
hwadslAtucChanIntervalRtxCWCount of units request retransmission on this channel during this interval.ro Gauge32 .1.3.6.1.2.1.10.94.1.1.12.1.65539 |
hwadslAtucChanIntervalRtxCorrectedCWCount of units corrected by retransmission on this channel during this interval.ro Gauge32 .1.3.6.1.2.1.10.94.1.1.12.1.65540 |
hwadslAtucChanIntervalRtxUncorrectedCWCount of units uncorrected by retransmission on this channel during this interval.ro Gauge32 .1.3.6.1.2.1.10.94.1.1.12.1.65541 |
hwadslAturChanIntervalFecBlksCount of all blocks received with FRC anomalies
on this channel during this interval.ro PerfIntervalCount (PerfHist-TC-MIB) .1.3.6.1.2.1.10.94.1.1.13.1.65536 |
hwadslAturChanIntervalHecBlksCount of all blocks received with HRC anomalies
on this channel during this interval.ro PerfIntervalCount (PerfHist-TC-MIB) .1.3.6.1.2.1.10.94.1.1.13.1.65537 |
hwadslAturChanIntervalCrcBlksCount of all blocks received with CRC anomalies
on this channel during this interval.ro PerfIntervalCount (PerfHist-TC-MIB) .1.3.6.1.2.1.10.94.1.1.13.1.65538 |
hwadslAturChanIntervalRtxCWCount of units request retransmission on this channel during this interval.ro Gauge32 .1.3.6.1.2.1.10.94.1.1.13.1.65539 |
hwadslAturChanIntervalRtxCorrectedCWCount of units corrected by retransmission on this channel during this interval.ro Gauge32 .1.3.6.1.2.1.10.94.1.1.13.1.65540 |
hwadslAturChanIntervalRtxUncorrectedCWCount of units uncorrected by retransmission on this channel during this interval.ro Gauge32 .1.3.6.1.2.1.10.94.1.1.13.1.65541 |
hwAdslAtucConfDownBitSwapEnables and disables the down bitswap of a template.
Options:
1. enabled(1) - Indicates that the downstream bit swap is enabled
2. disabled(2) - Indicates that the downstream bit swap is disabled
Default: enabled(1)rw Enumeration .1.3.6.1.2.1.10.94.1.1.14.1.65536 |
hwAdslAtucConfUpBitSwapEnables and disables the up bitswap of a template.
Options:
1. enabled(1) - Indicates that the upstream bit swap is enabled
2. disabled(2) - Indicates that the upstream bit swap is disabled
Default: enabled(1)rw Enumeration .1.3.6.1.2.1.10.94.1.1.14.1.65537 |
hwAdslTrellionsModeEnableEnables and disables the Trellions mode.
Options:
1. enabled(1) - Indicates that the trellis coding is enabled
2. disabled(2) - Indicates that the trellis coding is disabled
Default: enabled(1)rw Enumeration .1.3.6.1.2.1.10.94.1.1.14.1.65538 |
hwAdslTransmissionModeIndicates the transmission mode of this channel.
Options:
1. all(1) - All (G992.1, G992.2, T1.413)(Default)
2. fullRate(2) - Full rate(G992.1 or T1.413)
3. gliteOnly(3) - G992.2(g.lite) only
4. t1413Only(4) - T1.413 only
5. gdmtOnly(5) - G992.1,G992.3,G992.5,(g.dmt) only
6. ghs(6) - g.hs (G992.1,G992.2,G992.3,G992.4,G992.5,G992.5 is prior)
7. g992Dot1(7) - G992.1
8. g992Dot2(8) - G992.2
9. g992Dot3(9) - G992.3
10. g992Dot4(10) - G992.4
11. g992Dot5(11) - G992.5
12. adslAllOnly(12) - ADSL ALL ONLY
13. adslAndAdsl2(13) - G.992.1,G.992.3,T1.413(Not support)
Default: all(1)rw Enumeration .1.3.6.1.2.1.10.94.1.1.14.1.65539 |
hwadslLineAlarmConfProfileDyingGaspThis object enables/disables the report of LOSS-OF-POWER
alarm in an ADSL line, This object is defaulted enable(1).
Options:
1. enable (1) - The LOSS-OF-POWER alarm in an ADSL line will be reported
2. disable (2) - The LOSS-OF-POWER alarm in an ADSL line will not be reportedrw Enumeration .1.3.6.1.2.1.10.94.1.1.15.1.65536 |
hwAdslLinePvcTablePVC configuration table of the ADSL port and used to configure the VPI and VCI of the ADSL port.
The indexes of this table are ifIndex,hwAdsllinePvcVpi,and hwAdsllinePvcVci.
This table is used to configure only the CO PVC. SEQUENCE OF HwAdslLinePvcEntry .1.3.6.1.2.1.10.94.1.1.65536 |
hwAdslLinePvcEntryPVC configuration table of the ADSL port and used to configure the VPI and VCI of the ADSL port.
The indexes of this entry are ifIndex,hwAdsllinePvcVpi,and hwAdsllinePvcVci.
This table is used to configure only the CO PVC. HwAdslLinePvcEntry .1.3.6.1.2.1.10.94.1.1.65536.1 |
hwAdsllinePvcVpiThe VPI of the adsl line.ro Integer32 .1.3.6.1.2.1.10.94.1.1.65536.1.1 |
hwAdslLinePvcVciThe VCI of the adsl line.ro Integer32 .1.3.6.1.2.1.10.94.1.1.65536.1.2 |
hwAdslLinePvcVlanIdThe VLAN ID of the adsl line PVC.
Range: 1-4000rw Integer32 .1.3.6.1.2.1.10.94.1.1.65536.1.3 |
hwAdslLinePvcPriorityThe Priority value of the adsl line PVC.
Range: 0-7rw Integer32 .1.3.6.1.2.1.10.94.1.1.65536.1.4 |
hwAdslLinePvcDsBandThe down stream band of the adsl line PVC.
Range: 0-450rw Integer32 .1.3.6.1.2.1.10.94.1.1.65536.1.5 |
hwAdslLinePvcUsBandThe up stream band of the adsl line PVC.
Range: 0-450rw Integer32 .1.3.6.1.2.1.10.94.1.1.65536.1.6 |
hwAdslLinePvcMCastEnableThis object allows the adsl line PVC to support multicast.
Options:
1. enable(1) - Indicates that the PVC of the ADSL port is enabled to support the multicast
2. disable(2) - Indicates that the PVC of the ADSL port is disabled to support the multicast
Default: disable(2)rw Enumeration .1.3.6.1.2.1.10.94.1.1.65536.1.7 |
hwAdslLinePvcIGMPEnableThis object allows the adsl line PVC to support IGMP.
Options:
1. enable(1) - Indicates that the PVC of the ADSL port is enabled to support IGMP
2. disable(2) - Indicates that the PVC of the ADSL port is disabled to support IGMP
Default: disable(2)rw Enumeration .1.3.6.1.2.1.10.94.1.1.65536.1.8 |
hwAdslLinePvcIndexThe index of the adsl line PVC.
Range: 1-8rw Integer32 .1.3.6.1.2.1.10.94.1.1.65536.1.9 |
hwAdslLinePvcConnectTypeThe Connected type of the adsl line PVC.
Options:
1. auto(0) - The Connected type of the adsl line PVC is auto
2. llc1483B(1) - The Connected type of the adsl line PVC is llc1483B
3. pppoaLLC(2) - The Connected type of the adsl line PVC is pppoaLLC
4. pppoaVcmux(3) - The Connected type of the adsl line PVC is pppoaVcmux
5. ipoaLLc(4) - The Connected type of the adsl line PVC is ipoaLLc
6. ipoaVcmux(5) - The Connected type of the adsl line PVC is ipoaVcmuxro Enumeration .1.3.6.1.2.1.10.94.1.1.65536.1.10 |
hwAdslLinePvcRowStatusRow status. Add or delete a table item.rw RowStatus (SNMPv2-TC) .1.3.6.1.2.1.10.94.1.1.65536.1.11 |
hwAdslLineBitAllocationTableThe hwAdslLineBitAllocationTable contains the detailed bit-allocation
information for the current link. This information can be used to determine
whether a given sub-carrier loop has sufficient margin to support ADSL data
rates, and possibly to determine whether certain specific types of interfe-
rence or line attenuation exist.The bit allocation information are only va-
lid when the ATU-C is in the C-ACTIVE state.
The index of this table is ifIndex. SEQUENCE OF HwAdslLineBitAllocationEntry .1.3.6.1.2.1.10.94.1.1.65537 |
hwAdslLineBitAllocationEntryThe hwAdslLineBitAllocationTable contains the detailed bit-allocation
information for the current link. This information can be used to determine
whether a given sub-carrier loop has sufficient margin to support ADSL data
rates, and possibly to determine whether certain specific types of interfe-
rence or line attenuation exist.The bit allocation information are only va-
lid when the ATU-C is in the C-ACTIVE state.
The index of this entry is ifIndex. HwAdslLineBitAllocationEntry .1.3.6.1.2.1.10.94.1.1.65537.1 |
hwAdslLineDownStreamBitsPerFrameNumber of bits required per frame in the downstream data path for the
current configuration.ro Integer32 .1.3.6.1.2.1.10.94.1.1.65537.1.1 |
hwAdslLineUpStreamBitsPerFrameNumber of bits required per frame in the upstream data path for the
current configuration.ro Integer32 .1.3.6.1.2.1.10.94.1.1.65537.1.2 |
hwAdslLineDownStreamBitAllocLowwhen used to Adsl board
This object contains the first 128 downstream sub-carrier bit allocations
(sub-carrier # 1-128). This object is 64 bytes in length, where each byte
contains 2 sub-carrier values.
Byte 1 - 64 Downstream bit allocation (first 128 sub-carriers),
one byte for two sub-carriers.
1 Bits 4 - 7 # bits in 1st downstream sub-carrier
1 Bits 0 - 3 # bits in 2nd downstream sub-carrier
...
64 Bits 4 - 7 # bits in 127th downstream sub-carrier
64 Bits 0 - 3 # bits in 128th downstream sub-carrier
when used to Adsl2+ board
This object contains the first 256 downstream sub-carrier bit allocations
(sub-carrier # 1-256). This object is 256 bytes in length, where each byte
contains 1 sub-carrier values.
Byte 1 - 256 Downstream bit allocation (first 256 sub-carriers),
one byte for one sub-carriers.
1 Bits 0 - 7 # bits in 1st downstream sub-carrier
...
255 Bits 0 - 7 # bits in 255th downstream sub-carrier
256 Bits 0 - 7 # bits in 256th downstream sub-carrierro OCTET STRING .1.3.6.1.2.1.10.94.1.1.65537.1.3 |
hwAdslLineDownStreamBitAllocHighwhen used to Adsl board
This object contains the second 128 downstream sub-carrier bit allocations
(sub-carrier # 129-256). This object is 64 bytes in length, where each byte
contains 2 sub-carrier values.
Byte 1 - 64 Downstream bit allocation (second 128 sub-carriers),
one byte for two sub-carriers.
1 Bits 4 - 7 # bits in 129th downstream sub-carrier
1 Bits 0 - 3 # bits in 130th downstream sub-carrier
...
64 Bits 4 - 7 # bits in 255th downstream sub-carrier
64 Bits 0 - 3 # bits in 256th downstream sub-carrier
when used to Adsl2+ board
This object contains the second 256 downstream sub-carrier bit allocations
(sub-carrier # 257-512). This object is 256 bytes in length, where each byte
contains 1 sub-carrier values.
Byte 1 - 256 Downstream bit allocation (second 256 sub-carriers),
one byte for one sub-carriers.
1 Bits 0 - 7 # bits in 1st downstream sub-carrier
...
255 Bits 0 - 7 # bits in 255th downstream sub-carrier
256 Bits 0 - 7 # bits in 256th downstream sub-carrierro OCTET STRING .1.3.6.1.2.1.10.94.1.1.65537.1.4 |
hwAdslLineUpStreamBitAllocwhen used to Adsl board
This Object contains 64 upstream sub-carrier bit allocations (sub-carrier # 1-64).
This Object is 32 bytes in length, where each byte contains 2 sub-carrier values.
Byte 1-32 Upstream bit allocation information, total: 32 bytes,
one byte for two sub-carriers.
1 Bits 7 - 4 # bits in 1st upstream sub-carrier
1 Bits 3 - 0 # bits in 2nd upstream sub-carrier
...
32 Bits 7 - 4 # bits in 63rd upstream sub-carrier
32 Bits 3 - 0 # bits in 64th upstream sub-carrier
when used to Adsl2+ board
This Object contains 64 upstream sub-carrier bit allocations (sub-carrier # 1-64).
This Object is 64 bytes in length, where each byte contains 1 sub-carrier values.
Byte 1-64 Upstream bit allocation information, total: 64 bytes,
one byte for one sub-carriers.
1 Bits 7 - 0 # bits in 1st upstream sub-carrier
...
64 Bits 7 - 0 # bits in 64th upstream sub-carrierro OCTET STRING .1.3.6.1.2.1.10.94.1.1.65537.1.5 |
hwXdslPortTableThis table includes xDSL(e.g. adsl,g.shdsl,vdsl...)port information,
Used to support common attributes of the ADSL, G.SHDSL, and VDSL ports.
The index of this table is ifIndex. SEQUENCE OF HwXdslPortEntry .1.3.6.1.2.1.10.94.1.1.65538 |
hwXdslPortEntryThis table includes xDSL(e.g. adsl,g.shdsl,vdsl...)port information,
Used to support common attributes of the ADSL, G.SHDSL, and VDSL ports.
The index of this entry is ifIndex. HwXdslPortEntry .1.3.6.1.2.1.10.94.1.1.65538.1 |
hwXdslPortMaxMacLearnSet Max MAC count on the XDSL port.
Range: 0-255
Default: 255rw Integer32 .1.3.6.1.2.1.10.94.1.1.65538.1.1 |
hwXdslPortRateMonitorThresholdSet Port monitoring rate threshold percent. Including upstream and downstream.
Range: 0-100
Default: 0rw Integer32 .1.3.6.1.2.1.10.94.1.1.65538.1.2 |
hwXdslPortUpThresholdTxRateSet Port monitoring upstream rate threshold value.
Default: 0
Unit: bpsrw Gauge32 UNITS "bps" .1.3.6.1.2.1.10.94.1.1.65538.1.4 |
hwXdslPortDownThresholdTxRateSet Port monitoring downstream rate threshold value.
Default: 0
Unit: bpsrw Gauge32 UNITS "bps" .1.3.6.1.2.1.10.94.1.1.65538.1.5 |
hwXdslPortRateMonitorAlarmEnableEnables/Disables port rate monitor alarm.
Options:
1. enabled(1) - The port rate monitor alarm is enabled
2. disabled(2) - The port rate monitor alarm is disabledrw Enumeration .1.3.6.1.2.1.10.94.1.1.65538.1.6 |
hwXdslPortUpTimeDuration of the xDSL port activation.
Unit: secondsro Counter32 .1.3.6.1.2.1.10.94.1.1.65538.1.7 |
hwXdslPortNTEPowerStatusNTE power status, this object is defaulted off(2).
Options:
1. on(1) - NTE power on
2. off(2) - NTE power off
3. unknown(3) - Unknown statusro Enumeration .1.3.6.1.2.1.10.94.1.1.65538.1.8 |
hwXdslPortCurrentUpRateXdsl Port Current Upstream Value.
Range: 0-30000
Default: 0ro Integer32 .1.3.6.1.2.1.10.94.1.1.65538.1.500 |
hwXdslPortCurrentDownRateXdsl Port Current Downstream Value.
Range: 0-30000
Default: 0ro Integer32 .1.3.6.1.2.1.10.94.1.1.65538.1.501 |
hwXdslPortFarEndRunStateXdsl port far end Run state, This object is defaulted unknown(1).
Options:
1. unknown(1) - Unknown status
2. noModem(2) - Port is not connected to modem
3. handshake(3) - Handshake status
4. showtime(4) - Port is activatedro Enumeration .1.3.6.1.2.1.10.94.1.1.65538.1.600 |
hwXdslPortPowerStateXdsl port power state.
Options:
1. l0(1) - Full-on state
2. l2(2) - Low power state
3. l3(3) - Idle state
4. l1(4) - Low power state
5. invalidValue(-1) - Invalid value
Default: l0(1)ro Enumeration .1.3.6.1.2.1.10.94.1.1.65538.1.601 |
hwXdslPortUpCntThe up counts of Xdsl port.ro Unsigned32 .1.3.6.1.2.1.10.94.1.1.65538.1.700 |
hwXdslPortUpCntAdminStatusAdmin the up counts of xDSL port.
Options:
1. reset(0) - Reset the up counts of xDSL portrw Enumeration .1.3.6.1.2.1.10.94.1.1.65538.1.701 |
hwXdslPortLastUpTimeLast up time of a Xdsl port.ro DateAndTime (SNMPv2-TC) .1.3.6.1.2.1.10.94.1.1.65538.1.702 |
hwXdslPortLastDownTimeLast down time of a Xdsl port.ro DateAndTime (SNMPv2-TC) .1.3.6.1.2.1.10.94.1.1.65538.1.703 |
hwXdslPortClearUpCntTimeThe time when up counts of a Xdsl port is cleared.ro DateAndTime (SNMPv2-TC) .1.3.6.1.2.1.10.94.1.1.65538.1.704 |
hwXdslPortRetrainCntThe retrain counts of Xdsl Line.ro Unsigned32 .1.3.6.1.2.1.10.94.1.1.65538.1.705 |
hwXdslPortLastRetrainReasonThe last retrain reson of Xdsl Line, coded as bit mask.
Only one bit can be set valid, all bits set valid means invalid retrain reason.ro Unsigned32 .1.3.6.1.2.1.10.94.1.1.65538.1.706 |
hwXdslPortLoopFlagLoop flag.
Options:
1. false(0) - No loop
2. true (1) - Loopro Enumeration .1.3.6.1.2.1.10.94.1.1.65538.1.800 |
hwXdslPortUpThresholdSet Port monitoring upstream rate threshold percent value.
Range: 0-100rw Integer32 .1.3.6.1.2.1.10.94.1.1.65538.1.810 |
hwXdslPortDownThresholdSet Port monitoring downstream rate threshold percent value.
Range: 0-100rw Integer32 .1.3.6.1.2.1.10.94.1.1.65538.1.811 |
hwAdslLinePreActParaTableThis table provides one row for each ADSL PORT.
Each row contains the preactived Parameters.
The index of this table is ifIndex. SEQUENCE OF HwAdslLinePreActParaEntry .1.3.6.1.2.1.10.94.1.1.65539 |
hwAdslLinePreActParaEntryThis table provides one row for each ADSL PORT.
Each row contains the preactived Parameters.
The index of this entry is ifIndex. HwAdslLinePreActParaEntry .1.3.6.1.2.1.10.94.1.1.65539.1 |
hwAdslAtucPrevSnrMgnNoise Margin as seen by this ATU-C at the
time of the last adslAtucRateChangeTrap event.
Unit: tenth dBro Integer32 UNITS "tenth dB" .1.3.6.1.2.1.10.94.1.1.65539.1.1 |
hwAdslAturPrevSnrMgnNoise Margin as seen by this ATU-R at
the time of the last adslAtucRateChangeTrap event.
Unit: tenth dBro Integer32 UNITS "tenth dB" .1.3.6.1.2.1.10.94.1.1.65539.1.2 |
hwAdslAtucPrevAttainableRateIndicates the maximum attainable data rate
by the ATU-C at the time of the last
adslAtucRateChangeTrap event.
Unit: bpsro Unsigned32 UNITS "bps" .1.3.6.1.2.1.10.94.1.1.65539.1.3 |
hwAdslAturPrevAttainableRateIndicates the maximum attainable data rate
by the ATU-R at the time of the last
adslAtucRateChangeTrap event.
Unit: bpsro Unsigned32 UNITS "bps" .1.3.6.1.2.1.10.94.1.1.65539.1.4 |
hwAdslAtucPreAtnMeasured difference in the total power
transmitted as seen by this ATU-C at the time
of the last adslAtucRateChangeTrap event. in tenth dB.
Unit: tenth dBro Gauge32 UNITS "tenth dB" .1.3.6.1.2.1.10.94.1.1.65539.1.5 |
hwAdslAturPreAtnMeasured difference in the total power
transmitted as seen by this ATU-R at the time of the
last adslAtucRateChangeTrap event. in tenth dB.
Unit: tenth dBro Gauge32 UNITS "tenth dB" .1.3.6.1.2.1.10.94.1.1.65539.1.6 |
hwAdslPreActiveTimeThe last time at that the port was activated.ro DateAndTime (SNMPv2-TC) .1.3.6.1.2.1.10.94.1.1.65539.1.7 |
hwPortThreePriorityTableAdsl port three priority table.
The index of this table is ifIndex.obsolete SEQUENCE OF HwPortThreePriorityEntry .1.3.6.1.2.1.10.94.1.1.65540 |
hwPortThreePriorityEntryAdsl port three priority table.
The index of this entry is ifIndex.obsolete HwPortThreePriorityEntry .1.3.6.1.2.1.10.94.1.1.65540.1 |
hwPortThreePriorityEnableThree Priority status of the interface.
Options:
1. enable(1) - Adsl port three priority is enabled
2. disable(2) - Adsl port three priority is disabledrwobsolete Enumeration .1.3.6.1.2.1.10.94.1.1.65540.1.1 |
hwSlotMacMaxNoLimitTableMax mac learning no limit table.
The index of this table is hwFrameIndex and hwSlotIndex.obsolete SEQUENCE OF HwSlotMacMaxNoLimitEntry .1.3.6.1.2.1.10.94.1.1.65541 |
hwSlotMacMaxNoLimitEntryMax mac learning no limit table.
The index of this entry is hwFrameIndex and hwSlotIndex.obsolete HwSlotMacMaxNoLimitEntry .1.3.6.1.2.1.10.94.1.1.65541.1 |
hwSlotMacMaxNoLimitEnableThis object is used to set whether all the ports in the slot limits the maximum number of learning MAC addresses.
Options:
1. enable(1) - Don't limit the max NO. of learning mac addresses in the slot
2. disable(2) - Limit the max NO. of learning mac addresses in the slotrwobsolete Enumeration .1.3.6.1.2.1.10.94.1.1.65541.1.1 |
hwXdslPortStateStatisticTableXDSL port state statistic table, used to support the statistics information about the status mapping and status
of ports on the service boards, such as the ADSL, G.SHDSL and VDSL boards.
The indexes of this table are ifType, hwFrameIndex, and hwSlotIndex. SEQUENCE OF HwXdslPortStateStatisticEntry .1.3.6.1.2.1.10.94.1.1.65542 |
hwXdslPortStateStatisticEntryXDSL port state statistic table, used to support the statistics information about the status mapping and status
of ports on the service boards, such as the ADSL, G.SHDSL and VDSL boards.
The indexes of this entry are ifType, hwFrameIndex, and hwSlotIndex. HwXdslPortStateStatisticEntry .1.3.6.1.2.1.10.94.1.1.65542.1 |
hwXdslPortStatePortNumberThis Object is Port Number of One Slot.ro Unsigned32 .1.3.6.1.2.1.10.94.1.1.65542.1.1 |
hwXdslPortStateBitmapListThe type of port status:
2 failed;
8 testing;
9 activated;
10 activating;
11 deactivated;
18 localloopback;
19 remoteloopback;
20 blocked;
37 utopialoopback;
38 afeloopback;
39 hybridloopback;
255 unknown;
HwXdslPortStateBitmapList describes the states of all ports.
Every byte describe the current state of every port.
The length is equal to the value of the hwXdslPortStatePortNumber.ro OCTET STRING .1.3.6.1.2.1.10.94.1.1.65542.1.2 |
hwXdslTotalOfActivatedPortsThe total of the activated ports.ro Unsigned32 .1.3.6.1.2.1.10.94.1.1.65542.1.3 |
hwXdslTotalOfDeactivatedPortsThe total of the deactivated ports.ro Unsigned32 .1.3.6.1.2.1.10.94.1.1.65542.1.4 |
hwXdslTotalOfActivatingPortsThe total of the activating ports.ro Unsigned32 .1.3.6.1.2.1.10.94.1.1.65542.1.5 |
hwXdslTotalOfTestingPortsThe total of the Testing ports.ro Unsigned32 .1.3.6.1.2.1.10.94.1.1.65542.1.6 |
hwXdslTotalOfBlockedPortsThe total of the blocked ports.ro Unsigned32 .1.3.6.1.2.1.10.94.1.1.65542.1.7 |
hwXdslTotalOfLocalLoopbackPortsThe total of the local testing ports.ro Unsigned32 .1.3.6.1.2.1.10.94.1.1.65542.1.8 |
hwXdslTotalOfRemoteLoopbackPortsThe total of the remote testing ports.ro Unsigned32 .1.3.6.1.2.1.10.94.1.1.65542.1.9 |
hwXdslTotalOfFailedPortsThe total of the failed ports.ro Unsigned32 .1.3.6.1.2.1.10.94.1.1.65542.1.10 |
hwXdslTotalOfUnknownPortsThe total of the unknown testing ports.ro Unsigned32 .1.3.6.1.2.1.10.94.1.1.65542.1.11 |
hwadslLineExtConfProfileTableThis table contains information on the ADSL extend line
configuration. One entry in this table reflects a
extend line profile defined by a manager which can be used to
configure the ADSL line.
The index of this table is hwadslLineExtConfProfileName. SEQUENCE OF HwadslLineExtConfProfileEntry .1.3.6.1.2.1.10.94.1.1.65543 |
hwadslLineExtConfProfileEntryThis table contains information on the ADSL extend line
configuration. One entry in this table reflects a
extend line profile defined by a manager which can be used to
configure the ADSL line.
The index of this entry is hwadslLineExtConfProfileName. HwadslLineExtConfProfileEntry .1.3.6.1.2.1.10.94.1.1.65543.1 |
hwadslLineExtConfProfileNameThis object is used by the hwadslLineExtConfProfileTable
in order to identify a row of this table.
This object indicates the name of the extended line profile. OCTET STRING .1.3.6.1.2.1.10.94.1.1.65543.1.1 |
hwadslLineDisableToneSection1BeginThe begin index of section1.
Range: 0-511rw Integer32 .1.3.6.1.2.1.10.94.1.1.65543.1.2 |
hwadslLineDisableToneSection1EndThe end index of section1.
Range: 0-511rw Integer32 .1.3.6.1.2.1.10.94.1.1.65543.1.3 |
hwadslLineDisableToneSection1FlagThe enable flag of section1.
Options:
1. enabled(1) - The first tone section is enabled
2. disabled(2) - The first tone section is disabledrw Enumeration .1.3.6.1.2.1.10.94.1.1.65543.1.4 |
hwadslLineDisableToneSection2BeginThe begin index of section2.
Range: 0-511rw Integer32 .1.3.6.1.2.1.10.94.1.1.65543.1.5 |
hwadslLineDisableToneSection2EndThe end index of section2.
Range: 0-511rw Integer32 .1.3.6.1.2.1.10.94.1.1.65543.1.6 |
hwadslLineDisableToneSection2FlagThe enable flag of section2.
Options:
1. enabled(1) - The second tone section is enabled
2. disabled(2) - The second tone section is disabledrw Enumeration .1.3.6.1.2.1.10.94.1.1.65543.1.7 |
hwadslLineDisableToneSection3BeginThe begin index of section3.
Range: 0-511rw Integer32 .1.3.6.1.2.1.10.94.1.1.65543.1.8 |
hwadslLineDisableToneSection3EndThe end index of section3.
Range: 0-511rw Integer32 .1.3.6.1.2.1.10.94.1.1.65543.1.9 |
hwadslLineDisableToneSection3FlagThe enable flag of the third section.
Options:
1. enabled(1) - The third tone section is enabled
2. disabled(2) - The third tone section is disabledrw Enumeration .1.3.6.1.2.1.10.94.1.1.65543.1.10 |
hwadslLineDisableToneSection4BeginThe begin index of the fourth section.
Range: 0-511rw Integer32 .1.3.6.1.2.1.10.94.1.1.65543.1.11 |
hwadslLineDisableToneSection4EndThe end index of the fourth section.
Range: 0-511rw Integer32 .1.3.6.1.2.1.10.94.1.1.65543.1.12 |
hwadslLineDisableToneSection4FlagThe enable flag of the fourth section.
Range: 0-511
Options:
1. enabled(1) - The fourth tone section is enabled
2. disabled(2) - The fourth tone section is disabledrw Enumeration .1.3.6.1.2.1.10.94.1.1.65543.1.13 |
hwadsl2ChConfProfMinProtectionDsMinimum Impulse Noise Protection on Downstream direction. The
minimum impulse noise protection for the bearer channel, expressed
in symbols. The parameter can take the following values:
noProtection(0),
halfSymbol(1),
singleSymbol(2),
twoSymbols(4),
threeSymbols(6),
fourSymbols(8),
fiveSymbols(10),
sixSymbols(12),
sevenSymbols(14),
eightSymbols(16),
nineSymbols(18),
tenSymbols(20),
elevenSymbols(22),
twelveSymbols(24),
thirteenSymbols(26),
fourteenSymbols(28),
fifteenSymbols(30),
sixteenSymbols(32),
null(65535)
The value multiply 1/2 is the real value of Noise Protection values.rw HWADSLSYMBOLPROTECTION .1.3.6.1.2.1.10.94.1.1.65543.1.14 |
hwadsl2ChConfProfMinProtectionUsMinimum Impulse Noise Protection on Upstream direction. The
minimum impulse noise protection for the bearer channel, expressed
in symbols. The parameter can take the following values:
noProtection(0),
halfSymbol(1),
singleSymbol(2),
twoSymbols(4),
threeSymbols(6),
fourSymbols(8),
fiveSymbols(10),
sixSymbols(12),
sevenSymbols(14),
eightSymbols(16),
nineSymbols(18),
tenSymbols(20),
elevenSymbols(22),
twelveSymbols(24),
thirteenSymbols(26),
fourteenSymbols(28),
fifteenSymbols(30),
sixteenSymbols(32),
null(65535)
The value multiply 1/2 is the real value of Noise Protection values.rw HWADSLSYMBOLPROTECTION .1.3.6.1.2.1.10.94.1.1.65543.1.15 |
hwAdslExtDsMinTrainSnrMgnMaximum Trainning Margin in downstream.
Range: 0-310
Default: 30
Unit: tenth dBrw Integer32 .1.3.6.1.2.1.10.94.1.1.65543.1.16 |
hwAdslExtUsMinTrainSnrMgnMaximum Trainning Margin in upstream.
Range: 0-310
Default: 30
Unit: tenth dBrw Integer32 .1.3.6.1.2.1.10.94.1.1.65543.1.17 |
hwAdslExtDsMaxPsdMaximum PSD margin in downstream.rw Integer32 (-60..-30) UNITS "dBm/Hz" .1.3.6.1.2.1.10.94.1.1.65543.1.18 |
hwadsl2TSSiPsdMaskDsThe downstream PSD mask applicable at the U-C2 reference
point.
This parameter is used only for G992.3 or G992.5 and it may
impose PSD restrictions (breakpoints) in addition to the
Limit PSD mask defined in G992.5.
This is a string of 32 pairs of values in the following
structure:
Octets 0-1 - Index of 1st sub-carrier used in the context
of a first breakpoint.
Octet 2 - The PSD reduction for the sub-carrier indicated in
octets 0 and 1.
Octets 3-5 - Same, for a 2nd breakpoint.
Octets 6-8 - Same, for a 3rd breakpoint.
This architecture continues until octets 94-95, which are
associated with a 32nd breakpoint.
Each subcarrier index is an unsigned number in the range 1 and
NSCds. Each PSD reduction value is in the range 0 (0dBm/Hz) to
255 (-127.5dBm/Hz) with steps of 0.5dBm/Hz. Valid values are
in the range 0 to 190 (0 to -95dBm/Hz).
When the number of breakpoints is less than 32, all remaining
octets are set to the value 0. Note that the content of this
object should be correlated with the sub-carriers mask and with
the RFI setup.rw Adsl2PsdMaskDs (ADSL2-LINE-TC-MIB) .1.3.6.1.2.1.10.94.1.1.65543.1.19 |
hwadsl2TranMissionStardardMaskThe tranmission stardard mask.
The Mask bit and the corresponding Transmission Standard:
0x 1 1 1 1 1 1
ETSI T1.413 G992.5 G992.3 G992.2 G992.1
The Default BitMask: 0X0.rw Unsigned32 .1.3.6.1.2.1.10.94.1.1.65543.1.20 |
hwadsl2TransMissionAnnexMaskThe transMission annex Mask.
The Mask bit and the corresponding Transmission Annex:
0x 1 1 1 1 1
Annex .J Annex .M Annex .L Annex .B Annex .A
The Default BitMask: 0X0.rw Unsigned32 .1.3.6.1.2.1.10.94.1.1.65543.1.21 |
hwadsl2TransMissionAnnexMScopeAnnex M expand scope:
1-Tone Index(7~32)
2-Tone Index(7~36)
3-Tone Index(7~40)
4-Tone Index(7~44)
5-Tone Index(7~48)
6-Tone Index(7~52)
7-Tone Index(7~56)
8-Tone Index(7~60)
9-Tone Index(7~64)
-1-invalidValuerw HWADSL2ANNEXMSCOPE .1.3.6.1.2.1.10.94.1.1.65543.1.22 |
hwadsl2L2ModeStateThe state of L2 power management mode.
Options:
1. disabled(1) - L2 power management mode is disabled
2. enabled(2) - L2 power management mode is enabled
3. forced(3) - L2 power management mode is forced
Default: disabled(1)rw Enumeration .1.3.6.1.2.1.10.94.1.1.65543.1.23 |
hwadsl2L2ModeMinDataRateMinimum Data Rate in L2 Mode.
Range: 128-16384
Unit: Kbpsrw Integer32 .1.3.6.1.2.1.10.94.1.1.65543.1.24 |
hwadsl2L2ModeMaxDataRateMaximum Data Rate in L2 Mode.
Range: 128-16384
Default: 1024
Unit: Kbpsrw Integer32 .1.3.6.1.2.1.10.94.1.1.65543.1.25 |
hwadsl2L2ModePayloadRateThresholdThreshold for the Payload Rate Ratio.
Range: 128-16384
Default: 128
Unit: Kbpsrw Integer32 .1.3.6.1.2.1.10.94.1.1.65543.1.26 |
hwadsl2L2ModeGuardTimeGuard Time before entering L2 Mode.
Range: 0-1024
Default: 60
Unit: secondsrw Integer32 .1.3.6.1.2.1.10.94.1.1.65543.1.27 |
hwadsl2L2ModeIntervalTimeThe minimum interval between two records of L2 mode.
Range: 0-255
Default: 255
Unit: secondsrw Integer32 .1.3.6.1.2.1.10.94.1.1.65543.1.28 |
hwadsl2L2ModeIntervalPowerValueMaximum aggregate transmit power reduction per L2 request or L2 power trim.
Range: 0-31
Default: 3
Unit: dbrw Integer32 .1.3.6.1.2.1.10.94.1.1.65543.1.29 |
hwadsl2L2ModeTotalPowerValueTotal maximum aggregate transmit power reduction in L2.
Range: 0-31
Default: 9
Unit: dbrw Integer32 .1.3.6.1.2.1.10.94.1.1.65543.1.30 |
hwadslExtUsPhyRcontrolTo enable or disable the PHY-R function on upstream direction.
Options:
1. enable(1) - The PHY-R function on upstream direction is enabled
2. disable(2) - The PHY-R function on upstream direction is disabled
Default: disable(2)rw Enumeration .1.3.6.1.2.1.10.94.1.1.65543.1.31 |
hwadslExtUsINPmaxMaximum Impulse Noise Protection on upstream direction.
The parameter can take the following values:
noProtection(1),
halfSymbol(2),
singleSymbol(3),
twoSymbols(4),
threeSymbols(5),
fourSymbols(6),
fiveSymbols(7),
sixSymbols(8),
sevenSymbols(9),
eightSymbols(10),
nineSymbols(11),
tenSymbols(12),
elevenSymbols(13),
twelveSymbols(14),
thirteeSymbols(15),
fourteenSymbols(16),
fifteenSymbols(17),
sixteenSymbols(18)
The value multiply 1/2 is the real value of Noise Protection values.
Unit: DMT Symbol
Default: 1rw Adsl2SymbolProtection UNITS "DMT Symbol" .1.3.6.1.2.1.10.94.1.1.65543.1.32 |
hwadslExtUsMinRtxRatioMinimum rtxratio on upstream direction.
Range: 0-255
Default: 0
Unit: 1/256rw Integer32 .1.3.6.1.2.1.10.94.1.1.65543.1.33 |
hwadslExtUsMinRSoverheadThe minimum value of R/N on upstream direction.
Range: 0-128
Default: 0
Unit: 1/256rw Integer32 .1.3.6.1.2.1.10.94.1.1.65543.1.34 |
hwadslExtDsPhyRcontrolTo enable or disable the PHY-R function on downstream direction.
Options:
1. enable(1) - The PHY-R function on downstream direction is enabled
2. disable(2) - The PHY-R function on downstream direction is disabled
Default: disable(2)rw Enumeration .1.3.6.1.2.1.10.94.1.1.65543.1.35 |
hwadslExtDsINPmaxMaximum Impulse Noise Protection on downstream direction.
The parameter can take the following values:
noProtection(1),
halfSymbol(2),
singleSymbol(3),
twoSymbols(4),
threeSymbols(5),
fourSymbols(6),
fiveSymbols(7),
sixSymbols(8),
sevenSymbols(9),
eightSymbols(10),
nineSymbols(11),
tenSymbols(12),
elevenSymbols(13),
twelveSymbols(14),
thirteeSymbols(15),
fourteenSymbols(16),
fifteenSymbols(17),
sixteenSymbols(18)
The value multiply 1/2 is the real value of Noise Protection values.
Unit: DMT Symbolrw Adsl2SymbolProtection UNITS "DMT Symbol" .1.3.6.1.2.1.10.94.1.1.65543.1.36 |
hwadslExtDsMinRtxRatioMinimum rtxratio on downstream direction.
Range: 0-255
Default: 0
Unit: 1/256rw Integer32 .1.3.6.1.2.1.10.94.1.1.65543.1.37 |
hwadslExtDsMinRSoverheadThe minimum value of R/N on downstream direction.
Range: 0-128
Default: 0
Unit: 1/256rw Integer32 .1.3.6.1.2.1.10.94.1.1.65543.1.38 |
hwadsl2TSSiPsdMaskUsThe upstream PSD mask applicable at the U-C2 reference
point.
This parameter is used only for G992.3 or G992.5 and it may impose PSD
restrictions (breakpoints) in addition to the Limit PSD mask
defined in G992.5.
This is a string of 32 pairs of values in the following
structure:
Octets 0+1 - Index of 1st sub-carrier used in the context
of a first breakpoint.
Octet 2 - The PSD reduction for the sub-carrier indicated in
octets 0 and 1.
Octets 3-5 - Same, for a 2nd breakpoint.
Octets 6-8 - Same, for a 3rd breakpoint.
This architecture continues until octets 9-11, which are
associated with a fourth breakpoint.
Each subcarrier index is an unsigned number in the range 1 and
NSCus. Each PSD reduction value is in the range 0 (0dBm/Hz) to
255 (-127.5dBm/Hz) with steps of 0.5dBm/Hz. Valid values are
in the range 0 to 190 (0 to -95dBm/Hz).
When the number of breakpoints is less than 4, all remaining
octets are set to the value 0. Note that the content of this
object should be correlated with the sub-carriers mask and with
the RFI setup.rw Adsl2PsdMaskUs (ADSL2-LINE-TC-MIB) .1.3.6.1.2.1.10.94.1.1.65543.1.39 |
hwadslLConfProfAdslModeThe ADSL2 management model specified includes an ADSL Mode
attribute which identifies an instance of ADSL Mode-Specific
PSD Configuration object in the ADSL Line Profile. The
following classes of ADSL operating mode are defined.
Options:
1. defMode(1) - ADSL transmit mode is defMode
2. adsl(2) - ADSL transmit mode is adsl
3. adsl2Pots(3) - ADSL transmit mode is adsl2Pots
4. adsl2Isdn(4) - ADSL transmit mode is adsl2Isdn
5. adsl2PlusPots(5) - ADSL transmit mode is adsl2PlusPots
6. adsl2PlusIsdn(6) - ADSL transmit mode is adsl2PlusIsdn
7. adsl2ReachExtended(7) - ADSL transmit mode is adsl2ReachExtended
8. invalidValue(-1) - Invalid valuerw Enumeration .1.3.6.1.2.1.10.94.1.1.65543.1.40 |
hwadslLineExtConfProfileRowStatusThis object is used to create a new row or modify or
delete an existing row in this table.
A profile activated by setting this object to
'active'. When 'active' is set, the system
will validate the profile.
Before a profile can be deleted or taken out of
service, (by setting this object to 'destroy' or
'outOfService') it must be first unreferenced
from all associated lines.
If the creator of this MIB has chosen not
to implement 'dynamic assignment' of profiles, this
object's MIN-ACCESS is read-only and its value
is always to be 'active'.rw RowStatus (SNMPv2-TC) .1.3.6.1.2.1.10.94.1.1.65543.1.65535 |
hwadsl2L2ModeL2TimeThis minimum time (in seconds) between an Entry into the
L2 state and the first Power Trim in the L2 state and between
two consecutive Power Trims in the L2 State.
It ranges from 0 to 255 seconds.
Range: 0-255
Default: 30
Unit: secondsrw Integer32 .1.3.6.1.2.1.10.94.1.1.65543.1.65536 |
hwAdslLineLatestActParaTableThis table provides one row for each ADSL PORT.
Each row contains the latest actived Parameters.
The index of this table is ifIndex. SEQUENCE OF HwAdslLineLatestActParaEntry .1.3.6.1.2.1.10.94.1.1.65544 |
hwAdslLineLatestActParaEntryThis table provides one row for each ADSL PORT.
Each row contains the latest actived Parameters.
The index of this entry is ifIndex. HwAdslLineLatestActParaEntry .1.3.6.1.2.1.10.94.1.1.65544.1 |
hwAdslLineLatestActiveTimeActual time when latest actived.ro DateAndTime (SNMPv2-TC) .1.3.6.1.2.1.10.94.1.1.65544.1.1 |
hwAdslLineLatestDeactiveTimeActual time when latest deactived. If port is actived, the value is invalid.ro DateAndTime (SNMPv2-TC) .1.3.6.1.2.1.10.94.1.1.65544.1.2 |
hwAdslAtucLatestTxRateActual transmit rate on this channel when latest actived.
Unit: bpsro Gauge32 UNITS "bps" .1.3.6.1.2.1.10.94.1.1.65544.1.3 |
hwAdslAturLatestTxRateActual transmit rate on this channel when latest actived.
Unit: bpsro Gauge32 UNITS "bps" .1.3.6.1.2.1.10.94.1.1.65544.1.4 |
hwAdslAtucLatestSnrMgnNoise Margin as seen by this ATU-C at the time of the last adslAtucRateChangeTrap event. in tenth dB.
Unit: tenth dBro Integer32 UNITS "tenth dB" .1.3.6.1.2.1.10.94.1.1.65544.1.5 |
hwAdslAturLatestSnrMgnNoise Margin as seen by this ATU-R at the time of the last adslAtucRateChangeTrap event. in tenth dB.
Unit: tenth dBro Integer32 UNITS "tenth dB" .1.3.6.1.2.1.10.94.1.1.65544.1.6 |
hwAdslAtucLatestAtnMeasured difference in the total power transmitted as seen by this ATU-C at the time of the last adslAtucRateChangeTrap event. in tenth dB.
Unit: tenth dBro Gauge32 UNITS "tenth dB" .1.3.6.1.2.1.10.94.1.1.65544.1.7 |
hwAdslAturLatestAtnMeasured difference in the total power transmitted as seen by this ATU-R at the time of the last adslAtucRateChangeTrap event. in tenth dB.
Unit: tenth dBro Gauge32 UNITS "tenth dB" .1.3.6.1.2.1.10.94.1.1.65544.1.8 |
hwAdslAtucLatestAttainableRateIndicates the maximum attainable data rate by the ATU-C at the time of the last adslAtucRateChangeTrap event.
Unit: bpsro Gauge32 UNITS "bps" .1.3.6.1.2.1.10.94.1.1.65544.1.9 |
hwAdslAturLatestAttainableRateIndicates the maximum attainable data rate by the ATU-R at the time of the last adslAtucRateChangeTrap event.
Unit: bpsro Gauge32 UNITS "bps" .1.3.6.1.2.1.10.94.1.1.65544.1.10 |
hwAdslAtucLatestConfTxRateConfigured transmit rate for ADSL port,
in bps. See adslAtucConfRateChanRatio for information
regarding RADSL mode and ATUR transmit rate for
ATUC receive rates.
Unit: bpsro Gauge32 UNITS "bps" .1.3.6.1.2.1.10.94.1.1.65544.1.11 |
hwAdslAturLatestConfTxRateConfigured receive rate for ADSL port,
in bps. See adslAtucConfRateChanRatio for information
regarding RADSL mode and ATUR transmit rate for
ATUC receive rates.
Unit: bpsro Gauge32 UNITS "bps" .1.3.6.1.2.1.10.94.1.1.65544.1.12 |
hwAdslAtucLatestInterleaveDelayInterleave Delay for this channel when latest actived.
Unit: millisecondsro Gauge32 UNITS "milliseconds" .1.3.6.1.2.1.10.94.1.1.65544.1.13 |
hwAdslAturLatestInterleaveDelayInterleave Delay for this channel when latest actived.
Unit: millisecondsro Gauge32 UNITS "milliseconds" .1.3.6.1.2.1.10.94.1.1.65544.1.14 |
hwAdslAtucLatestTargetSnrMgnPort Signal/Noise Margin.
Range: 0-310
Unit: tenth dBro Integer32 .1.3.6.1.2.1.10.94.1.1.65544.1.15 |
hwAdslAturLatestTargetSnrMgnPort Signal/Noise Margin.
Range: 0-310
Unit: tenth dBro Integer32 .1.3.6.1.2.1.10.94.1.1.65544.1.16 |
hwAdslAtucLatestTxRateThresholdPort down stream threshold.
Unit: bpsro Gauge32 UNITS "bps" .1.3.6.1.2.1.10.94.1.1.65544.1.17 |
hwAdslAturLatestTxRateThresholdPort up stream threshold.
Unit: bpsro Gauge32 UNITS "bps" .1.3.6.1.2.1.10.94.1.1.65544.1.18 |
hwXdslPortPerformanceStatTableXDSL port performance statistic table.
The indexes of this table are ifIndex and hwXdslPort15minutesPerformanceInterval. SEQUENCE OF HwXdslPortPerformanceStatEntry .1.3.6.1.2.1.10.94.1.1.65545 |
hwXdslPortPerformanceStatEntryXDSL port performance statistic table.
The indexes of this entry are ifIndex and hwXdslPort15minutesPerformanceInterval. HwXdslPortPerformanceStatEntry .1.3.6.1.2.1.10.94.1.1.65545.1 |
hwXdslPort15minutesPerformanceIntervalThe index of the interval which is queried.
Range: 0-96 Integer32 .1.3.6.1.2.1.10.94.1.1.65545.1.1 |
hwXdslPort15minutesPerformanceInBytesRead the receive bytes of xDSL port during 15 minutes.ro Counter32 .1.3.6.1.2.1.10.94.1.1.65545.1.2 |
hwXdslPort15minutesPerformanceOutBytesRead the transmit bytes of xDSL port during 15 minutes.ro Counter32 .1.3.6.1.2.1.10.94.1.1.65545.1.3 |
hwXdslPortSyncSuccNumberNumber of successful activations of the xDSL port within 15 minutes.ro Counter32 .1.3.6.1.2.1.10.94.1.1.65545.1.4 |
hwXdslPortSyncFailNumberNumber of failed activations of the xDSL port within 15 minutes.ro Counter32 .1.3.6.1.2.1.10.94.1.1.65545.1.5 |
hwXdslPortAtucCodeViolationNumber of head errors of the ATUC cell within 15 minutes.ro Counter32 .1.3.6.1.2.1.10.94.1.1.65545.1.6 |
hwXdslPortAturCodeViolationNumber of head errors of the ATUR cell within 15 minutes.ro Counter32 .1.3.6.1.2.1.10.94.1.1.65545.1.7 |
hwXdslPortAtucFecSecondsSeconds of the ATUC FEC errors within 15 minutes.ro Counter32 .1.3.6.1.2.1.10.94.1.1.65545.1.8 |
hwXdslPortAturFecSecondsSeconds of the ATUR FEC errors within 15 minutes.ro Counter32 .1.3.6.1.2.1.10.94.1.1.65545.1.9 |
hwXdslPortCurrent15minutesStatTimeSeconds passed within the current 15 minutes.ro Counter32 .1.3.6.1.2.1.10.94.1.1.65545.1.10 |
hwAdslPortPerformanceStatTableThis table is used to describe the performance statistics of the ADSL port within 15 minutes.
The indexes of this table are ifIndex and hwAdslPort15minutesPerformanceInterval. SEQUENCE OF HwAdslPortPerformanceStatEntry .1.3.6.1.2.1.10.94.1.1.65546 |
hwAdslPortPerformanceStatEntryThis table is used to describe the performance statistics of the ADSL port within 15 minutes.
The indexes of this entry are ifIndex and hwAdslPort15minutesPerformanceInterval. HwAdslPortPerformanceStatEntry .1.3.6.1.2.1.10.94.1.1.65546.1 |
hwAdslPort15minutesPerformanceIntervalThe index of the interval which is queried.
Range: 0-96 Integer32 .1.3.6.1.2.1.10.94.1.1.65546.1.1 |
hwAdslPort15minutesPerformanceInBytesRead the receive bytes of xDSL port during 15 minutes.ro Counter32 .1.3.6.1.2.1.10.94.1.1.65546.1.2 |
hwAdslPort15minutesPerformanceOutBytesRead the transmit bytes of xDSL port during 15 minutes.ro Counter32 .1.3.6.1.2.1.10.94.1.1.65546.1.3 |
hwAdslPortSyncSuccNumberNumber of successful activations within 15 minutes.ro Counter32 .1.3.6.1.2.1.10.94.1.1.65546.1.4 |
hwAdslPortSyncFailNumberNumber of failed activations within 15 minutes.ro Counter32 .1.3.6.1.2.1.10.94.1.1.65546.1.5 |
hwAdslPortAtucCodeViolationSeconds of head errors of the ATUC cell within 15 minutes.ro Counter32 .1.3.6.1.2.1.10.94.1.1.65546.1.6 |
hwAdslPortAturCodeViolationSeconds of head errors of the ATUC cell within 15 minutes.ro Counter32 .1.3.6.1.2.1.10.94.1.1.65546.1.7 |
hwAdslPortAtucFecSecondsSeconds of the ATUC FEC errors within 15 minutes.ro Counter32 .1.3.6.1.2.1.10.94.1.1.65546.1.8 |
hwAdslPortAturFecSecondsError seconds of the ATUR FEC within 15 minutes.ro Counter32 .1.3.6.1.2.1.10.94.1.1.65546.1.9 |
hwAdslPortCurrent15minutesTimeElapseSeconds that is passed within the current 15 minutes.ro Counter32 .1.3.6.1.2.1.10.94.1.1.65546.1.10 |
hwAdslPortAtucHecDropCellsCntATUC cells discarded with HEC Errors.ro Counter32 .1.3.6.1.2.1.10.94.1.1.65546.1.11 |
hwAdslPortAturHecDropCellsCntATUR cells discarded with HEC Errors.ro Counter32 .1.3.6.1.2.1.10.94.1.1.65546.1.12 |
hwAdslLineConfProfileThe value of this object identifies the row
in the ADSL Line Configuration Profile Table,
(adslLineConfProfileTable), which applies for this
ADSL line, and channels if applicable.
For 'dynamic' mode, in the case which the
configuration profile has not been set, the
value will be set to 'DEFVAL'.
If the creator of this MIB has chosen not
to implement 'dynamic assignment' of profiles, this
object's MIN-ACCESS is read-only.ro OCTET STRING .1.3.6.1.2.1.10.94.1.1.65546.1.13 |
hwAdslPort15minUpTimeUp time in the interval.
Unit: secondsro Counter32 .1.3.6.1.2.1.10.94.1.1.65546.1.14 |
hwAdslAtucCurrAtnMeasured difference in the total power transmitted by
the peer ATU and the total power received by this ATU.
Range: 0-630
Unit: tenth dBro Gauge32 .1.3.6.1.2.1.10.94.1.1.65546.1.15 |
hwAdslAtucCurrSnrMgnNoise Margin as seen by this ATU with respect to its
received signal in tenth dB.
Unit: tenth dBro Integer32 (-640..640) UNITS "tenth dB" .1.3.6.1.2.1.10.94.1.1.65546.1.16 |
hwAdslAtucCurrAttainableRateIndicates the maximum currently attainable data rate
by the ATU. This value will be equal or greater than
the current line rate.
Unit: bpsro Gauge32 UNITS "bps" .1.3.6.1.2.1.10.94.1.1.65546.1.17 |
hwAdslAtucChanCurrTxRateActual transmit rate on this channel.
Unit: bpsro Gauge32 UNITS "bps" .1.3.6.1.2.1.10.94.1.1.65546.1.18 |
hwAdslAturCurrAtnMeasured difference in the total power transmitted by
the peer ATU and the total power received by this ATU.
Range: 0-630
Unit: tenth dBro Gauge32 .1.3.6.1.2.1.10.94.1.1.65546.1.19 |
hwAdslAturCurrSnrMgnNoise Margin as seen by this ATU with respect to its
received signal in tenth dB.
Unit: tenth dBro Integer32 (-640..640) UNITS "tenth dB" .1.3.6.1.2.1.10.94.1.1.65546.1.20 |
hwAdslAturCurrAttainableRateIndicates the maximum currently attainable data rate
by the ATU. This value will be equal or greater than
the current line rate.
Unit: bpsro Gauge32 UNITS "bps" .1.3.6.1.2.1.10.94.1.1.65546.1.21 |
hwAdslAturChanCurrTxRateActual transmit rate on this channel.
Unit: bpsro Gauge32 UNITS "bps" .1.3.6.1.2.1.10.94.1.1.65546.1.22 |
hwAdslAtucIntervalESsCount of Errored Seconds in the interval.
The errored second parameter is a count of
one-second intervals containing one or more crc
anomalies, or one or more los or sef defects.
Unit: secondsro PerfIntervalCount UNITS "seconds" .1.3.6.1.2.1.10.94.1.1.65546.1.23 |
hwAdslAtucIntervalLofsCount of seconds in the interval when there was Loss
of Framing.
Unit: secondsro PerfIntervalCount UNITS "seconds" .1.3.6.1.2.1.10.94.1.1.65546.1.24 |
hwAdslAtucIntervalLolsCount of seconds in the interval when there was Loss
of Link.
Unit: secondsro PerfIntervalCount UNITS "seconds" .1.3.6.1.2.1.10.94.1.1.65546.1.25 |
hwAdslAtucIntervalLossCount of seconds in the interval when there was Loss
of Signal.
Unit: secondsro PerfIntervalCount UNITS "seconds" .1.3.6.1.2.1.10.94.1.1.65546.1.26 |
hwAdslAtucIntervalLprsCount of seconds in the interval when there was Loss of Power.
Unit: secondsro PerfIntervalCount UNITS "seconds" .1.3.6.1.2.1.10.94.1.1.65546.1.27 |
hwAdslAturIntervalESsCount of Errored Seconds in the interval.
The errored second parameter is a count of
one-second intervals containing one or more crc
anomalies, or one or more los or sef defects.
Unit: secondsro PerfIntervalCount UNITS "seconds" .1.3.6.1.2.1.10.94.1.1.65546.1.28 |
hwAdslAturIntervalLofsCount of seconds in the interval when there was
Loss of Framing.
Unit: secondsro PerfIntervalCount UNITS "seconds" .1.3.6.1.2.1.10.94.1.1.65546.1.29 |
hwAdslAturIntervalLossCount of seconds in the interval when there was Loss of Signal.
Unit: secondsro PerfIntervalCount UNITS "seconds" .1.3.6.1.2.1.10.94.1.1.65546.1.30 |
hwAdslAturIntervalLprsCount of seconds in the interval when there was Loss of Power.
Unit: secondsro PerfIntervalCount UNITS "seconds" .1.3.6.1.2.1.10.94.1.1.65546.1.31 |
hwAdslAtucChanIntervalReceivedBlksCount of all encoded blocks received on this channel
during this interval.ro PerfIntervalCount (PerfHist-TC-MIB) .1.3.6.1.2.1.10.94.1.1.65546.1.32 |
hwAdslAtucChanIntervalTransmittedBlksCount of all encoded blocks transmitted on this
channel during this interval.ro PerfIntervalCount (PerfHist-TC-MIB) .1.3.6.1.2.1.10.94.1.1.65546.1.33 |
hwAdslAtucChanIntervalCorrectedBlksCount of all blocks received with errors that were
corrected on this channel during this interval.ro PerfIntervalCount (PerfHist-TC-MIB) .1.3.6.1.2.1.10.94.1.1.65546.1.34 |
hwAdslAtucChanIntervalUncorrectBlksCount of all blocks received with uncorrectable
errors on this channel during this interval.ro PerfIntervalCount (PerfHist-TC-MIB) .1.3.6.1.2.1.10.94.1.1.65546.1.35 |
hwAdslAturChanIntervalReceivedBlksCount of all encoded blocks received on this channel
during this interval.ro PerfIntervalCount (PerfHist-TC-MIB) .1.3.6.1.2.1.10.94.1.1.65546.1.36 |
hwAdslAturChanIntervalTransmittedBlksCount of all encoded blocks transmitted on this
channel during this interval.ro PerfIntervalCount (PerfHist-TC-MIB) .1.3.6.1.2.1.10.94.1.1.65546.1.37 |
hwAdslAturChanIntervalCorrectedBlksCount of all blocks received with errors that were
corrected on this channel during this interval.ro PerfIntervalCount (PerfHist-TC-MIB) .1.3.6.1.2.1.10.94.1.1.65546.1.38 |
hwAdslAturChanIntervalUncorrectBlksCount of all blocks received with uncorrectable
errors on this channel during this interval.ro PerfIntervalCount (PerfHist-TC-MIB) .1.3.6.1.2.1.10.94.1.1.65546.1.39 |
hwAdslAtucIntervalSesLFor the each interval, adslAtucIntervalSesL
reports the number of seconds during which
there have been severely errored seconds-line.
Unit: secondsro PerfIntervalCount UNITS "seconds" .1.3.6.1.2.1.10.94.1.1.65546.1.40 |
hwAdslAtucIntervalUasLFor the each interval, adslAtucIntervalUasL
reports the number of seconds during which
there have been unavailable seconds-line.
Unit: secondsro PerfIntervalCount UNITS "seconds" .1.3.6.1.2.1.10.94.1.1.65546.1.41 |
hwAdslAturIntervalSesLFor the each interval, adslAturIntervalSesL
reports the number of seconds during which
there have been severely errored seconds-line.
Unit: secondsro PerfIntervalCount UNITS "seconds" .1.3.6.1.2.1.10.94.1.1.65546.1.42 |
hwAdslAturIntervalUasLFor the each interval, adslAturIntervalUasL
reports the number of seconds during which
there have been unavailable seconds-line.
Unit: secondsro PerfIntervalCount UNITS "seconds" .1.3.6.1.2.1.10.94.1.1.65546.1.43 |
hwAdslPortCurrentActModeInstantaneous value of the technology type
that line is currently trained up under.
Options:
1. adsl(1) - Indicates that line is currently trained up under adsl type
2. adsl2(2) - Indicates that line is currently trained up under adsl2 type
3. adsl2plus(3) - Indicates that line is currently trained up under adsl2+ typero Enumeration .1.3.6.1.2.1.10.94.1.1.65546.1.44 |
hwAdslPortRateChangeTrapParaTableADSL line rate change trap parameter table.
The index of this table is ifIndex. SEQUENCE OF HwAdslPortRateChangeTrapParaEntry .1.3.6.1.2.1.10.94.1.1.65547 |
hwAdslPortRateChangeTrapParaEntryADSL line rate change trap parameter table.
The index of this entry is ifIndex. HwAdslPortRateChangeTrapParaEntry .1.3.6.1.2.1.10.94.1.1.65547.1 |
hwAdslPortRateChangeTrapIPIAIDThe port IPIAID is reported when the port rate changes.ro OCTET STRING .1.3.6.1.2.1.10.94.1.1.65547.1.1 |
hwAdslPortRateChangeTrapMUXIDThe port MUXID is reported when the port rate changes.ro OCTET STRING .1.3.6.1.2.1.10.94.1.1.65547.1.2 |
hwAdslPortRateChangeTrapTimeStampThe time stamp of Line rate change trap.
Standard Unix format; as the number of seconds since 1/1/1970 (UNIT:Second).ro Counter32 .1.3.6.1.2.1.10.94.1.1.65547.1.3 |
hwAdslPortRateChangeTrapDSLineRateDown stream line rate after line rate change.ro Gauge32 .1.3.6.1.2.1.10.94.1.1.65547.1.4 |
hwAdslPortRateChangeTrapUSLineRateUp stream line rate after line rate change.ro Gauge32 .1.3.6.1.2.1.10.94.1.1.65547.1.5 |
hwAdslPortRateChangeTrapEventTypeEvent type reported during the previous change of the rate.
If both the upstream and downstream rates change, this leaf object outputs character string 'DU'.
If only the upstream rates changes, this leaf object outputs character string 'US'.
If only the downstream rates changes, this leaf object outputs character string 'DS'.ro OCTET STRING .1.3.6.1.2.1.10.94.1.1.65547.1.6 |
hwAdslPortRateChangeTrapDslTypeDSL line type of the port whose rate changes.ro OCTET STRING .1.3.6.1.2.1.10.94.1.1.65547.1.7 |
hwXdslSysManagementParaTable OBJECT IDENTIFIER .1.3.6.1.2.1.10.94.1.1.65548 |
hwAdslPortRateChangeTrapConfigEnable or disable ADSL port line-rate change trap feature.
Options:
1. enabled(1) - ADSL port line-rate change trap feature is enabled
2. disabled(2) - ADSL port line-rate change trap feature is disabledrw Enumeration .1.3.6.1.2.1.10.94.1.1.65548.1 |
hwAdsl2SCStateTableThe table adsl2SCStatusTable contains status parameters
of the ADSL2 sub-carriers.
The indexes of this table are ifIndex and hwAdsl2SCStatusDirection. SEQUENCE OF HwAdsl2SCStatusEntry .1.3.6.1.2.1.10.94.1.1.65549 |
hwAdsl2SCStatusEntryThe table adsl2SCStatusTable contains status parameters
of the ADSL2 sub-carriers.
The indexes of this entry are ifIndex and hwAdsl2SCStatusDirection. HwAdsl2SCStatusEntry .1.3.6.1.2.1.10.94.1.1.65549.1 |
hwAdsl2SCStatusDirectionThe direction of the sub-carrier is either upstream or downstream.
Options:
1. upstream(1) - Upstream sub-carrier
2. downstream(2) - Downstream sub-carrier Enumeration .1.3.6.1.2.1.10.94.1.1.65549.1.1 |
hwAdsl2SCStatusSnrThe SNR Margin per sub-carrier, expressing the ratio between
the received signal power and received noise power per
subscriber. It is an array of 512 octets, designed for
supporting up to 512 (downstream) sub-carriers.
The number of utilized octets on downstream direction depends
on NSCds, and on upstream direction it depends on NSCus. This
value is referred to here as NSC.
Octet i (0 <= i < NSC) is set to a value in the range 0 to
254 to indicate that the respective downstream or upstream sub-
carrier i has SNR of: (-32 + Adsl2SubcarrierSnr(i)/2) in dB
(i.e., -32 to 95dB).
The special value 255 means that no measurement could be done
for the subcarrier because it is out of the PSD mask passband
or that the noise PSD is out of range to be represented.
Each value in this array is 8 bits wide.ro OCTET STRING .1.3.6.1.2.1.10.94.1.1.65549.1.2 |
hwAdsl2SCStatusBitsAllocThe bits allocation per sub-carrier. An array of 256 octets
(512 nibbles), designed for supporting up to 512 (downstream)
sub-carriers.
The number of utilized nibbles on downstream direction depends
on NSCds, and on upstream direction it depends on NSCus. This
value is referred to here as NSC.
Nibble i (0 <= i < NSC) is set to a value in the range 0
to 15 to indicate that the respective downstream or upstream
sub-carrier i has the same amount of bits allocation.ro OCTET STRING .1.3.6.1.2.1.10.94.1.1.65549.1.3 |
hwAdsl2SCStatusGainAllocThe gain allocation per sub-carrier. An array of 512 16-bits
values, designed for supporting up to 512 (downstream) sub-
carriers.
The number of utilized octets on downstream direction depends
on NSCds, and on upstream direction it depends on NSCus. This
value is referred to here as NSC.
Value i (0 <= i < NSC) is in the range 0 to 4093 to indicate
that the respective downstream or upstream sub-carrier i has the
same amount of gain value.
The gain value is represented as a multiple of 1/512 on a
linear scale. Each value in this array is 16 bits wide and is
stored in big endian format.ro OCTET STRING .1.3.6.1.2.1.10.94.1.1.65549.1.4 |
hwAdsl2SCStatusLogAn array of up to 512 real H(f) logarithmic representation
values in dB for the respective transmission direction. It is
designed to support up to 512 (downstream) sub-carriers.
The number of utilized values on downstream direction depends
on NSCds, and on upstream direction it depends on NSCus. This
value is referred to here as NSC.
Each array entry represents the real Hlog(f = i*Df) value for a
particular sub-carrier index i, (0 <= i < NSC).
The real Hlog(f) value is represented as (6-m(i)/10), with m(i)
in the range 0 to 1022. A special value m=1023 indicates that
no measurement could be done for the subcarrier because it is
out of the passband or that the attenuation is out of range to
be represented. This parameter is applicable in loop
diagnostic procedure and initialization.
Each value in this array is 16 bits wide and is stored
in big endian format.ro OCTET STRING .1.3.6.1.2.1.10.94.1.1.65549.1.5 |
hwAdsl2SCStatusQlnAn array of up to 512 real Quiet Line Noise values in dBm/Hz
for the respective transmission direction. It is designed for
up to 512 (downstream) sub-carriers.
The number of utilized values on downstream direction depends
on NSCds, and on upstream direction it depends on NSCus. This
value is referred to here as NSC.
Each array entry represents the QLN(f = i*Df) value for a
particular sub-carrier index i, (0 <= i < NSC).
The QLN(f) is represented as ( -23-n(i)/2), with n(i) in the
range 0 to 254. A special value n(i)=255 indicates that no
measurement could be done for the subcarrier because it is out
of the passband or that the noise PSD is out of range to be
represented.
This parameter is applicable in loop diagnostic procedure and
initialization. Each value in this array is 8 bits wide.ro OCTET STRING .1.3.6.1.2.1.10.94.1.1.65549.1.6 |
hwAdsl2SCStatusSnrMarginSNR Margin is the maximum increase in dB of the noise power
received at the ATU (ATU-R on downstream direction and ATU-C
on upstream direction), such that the BER requirements are met
for all bearer channels received at the ATU. It ranges from
-640 to 630 units of 0.1 dB (physical values are -64 to
63 dB).ro OCTET STRING .1.3.6.1.2.1.10.94.1.1.65549.1.7 |
hwAdsl2SCStatusTxPSDThe PSD MASK per sub-carrier.An array of 512 16-bits
values, designed for supporting up to 512 (downstream) sub-carriers.
It ranges from -1400 to -300 units of 0.1 dBm/Hz (physical values
are -140 to -30 dBm/Hz).ro OCTET STRING .1.3.6.1.2.1.10.94.1.1.65549.1.8 |
hwxdslDynamicProfTableThis table includes common parameters of the xdsl Dynamic profile.
The index of this table is hwxdslDynamicProfProfileName. SEQUENCE OF HwxdslDynamicProfEntry .1.3.6.1.2.1.10.94.1.1.65550 |
hwxdslDynamicProfEntryThis table includes common parameters of the xdsl Dynamic profile.
The index of this entry is hwxdslDynamicProfProfileName. HwxdslDynamicProfEntry .1.3.6.1.2.1.10.94.1.1.65550.1 |
hwxdslDynamicProfProfileNameThe name of xdsl Dynamic Profile. OCTET STRING .1.3.6.1.2.1.10.94.1.1.65550.1.1 |
hwxdslDynamicProfXtuTransSysEnaXtu Transmission System Enabling (ATSE). A list of the
different coding types enabled in this profile. It is coded
in a bit-map representation with 1 or more bits set. A bit
set to '1' means that the XTUs may apply the respective
coding for the XDSL line. A bit set to '0' means that
the XTUs cannot apply the respective coding for the XDSL
line. All 'reserved' bits should be set to '0'.rw Bits .1.3.6.1.2.1.10.94.1.1.65550.1.2 |
hwxdslDynamicProfBitSwapDSEnables or disables the bit swap downstream of a line.
Options:
1. disable(1) - The bit swap downstream of a line is disabled
2. enable(2) - The bit swap downstream of a line is enabled
3. invalidValue(-1) - Invalid valuerw Enumeration .1.3.6.1.2.1.10.94.1.1.65550.1.3 |
hwxdslDynamicProfBitSwapUSEnables or disables the bit swap upstream of a line.
Options:
1. disable(1) - The bit swap upstream of a line is disabled
2. enable(2) - The bit swap upstream of a line is enabled
3. invalidValue(-1) - Invalid valuerw Enumeration .1.3.6.1.2.1.10.94.1.1.65550.1.4 |
hwxdslDynamicProfTargetSnrmDsThe target Noise Margin the xTU-R receiver shall achieve,
relative to the BER requirement for each of the downstream
bearer channels, to successfully complete initialization.
The target noise margin ranges from 0 to 310 units of 0.1 dB
(Physical values are 0 to 31 dB).
Range: 0-310
Unit: 0.1 dBrw Unsigned32 .1.3.6.1.2.1.10.94.1.1.65550.1.5 |
hwxdslDynamicProfTargetSnrmUsThe target Noise Margin the xTU-C receiver shall achieve,
relative to the BER requirement for each of the downstream
bearer channels, to successfully complete initialization.
The target noise margin ranges from 0 to 310 units of 0.1 dB
(Physical values are 0 to 31 dB).
Range: 0-310
Unit: 0.1 dBrw Unsigned32 .1.3.6.1.2.1.10.94.1.1.65550.1.6 |
hwxdslDynamicProfMaxSnrmDsThe maximum Noise Margin the xTU-R receiver shall achieve,
relative to the BER requirement for each of the downstream
bearer channels, to successfully complete initialization.
The target noise margin ranges from 0 to 310 units of 0.1 dB
(Physical values are 0 to 31 dB).
Range: 0-310
Unit: 0.1 dBrw Unsigned32 .1.3.6.1.2.1.10.94.1.1.65550.1.7 |
hwxdslDynamicProfMaxSnrmUsThe maximum Noise Margin the xTU-C receiver shall achieve,
relative to the BER requirement for each of the downstream
bearer channels, to successfully complete initialization.
The target noise margin ranges from 0 to 310 units of 0.1 dB
(Physical values are 0 to 31 dB).
Range: 0-310
Unit: 0.1 dBrw Unsigned32 .1.3.6.1.2.1.10.94.1.1.65550.1.8 |
hwxdslDynamicProfMinSnrmDsThe minimum Noise Margin the xTU-R receiver shall achieve,
relative to the BER requirement for each of the downstream
bearer channels, to successfully complete initialization.
The target noise margin ranges from 0 to 310 units of 0.1 dB
(Physical values are 0 to 31 dB).
Range: 0-310
Unit: 0.1 dBrw Unsigned32 .1.3.6.1.2.1.10.94.1.1.65550.1.9 |
hwxdslDynamicProfMinSnrmUsThe minimum Noise Margin the xTU-C receiver shall achieve,
relative to the BER requirement for each of the downstream
bearer channels, to successfully complete initialization.
The target noise margin ranges from 0 to 310 units of 0.1 dB
(Physical values are 0 to 31 dB).
Range: 0-310
Unit: 0.1 dBrw Unsigned32 .1.3.6.1.2.1.10.94.1.1.65550.1.10 |
hwxdslDynamicProfCh1MinProtectionDsMinimum Impulse Noise Protection on Downstream direction. The
minimum impulse noise protection for the bearer channel,
expressed in symbols. The parameter can take the following
values: noProtection (i.e., INP not required), halfSymbol
(i.e., INP length is 1/2 symbol) and 1-16 symbols in steps
of 1 symbol.
Options:
1. noProtection (1) - Indicates that the INP value is 0
2. halfSymbol (2) - Indicates that the INP value is 0.5
3. singleSymbol (3) - Indicates that the INP value is 1
4. twoSymbols (4) - Indicates that the INP value is 2
5. threeSymbols (5) - Indicates that the INP value is 3
6. fourSymbols (6) - Indicates that the INP value is 4
7. fiveSymbols (7) - Indicates that the INP value is 5
8. sixSymbols (8) - Indicates that the INP value is 6
9. sevenSymbols (9) - Indicates that the INP value is 7
10. eightSymbols (10) - Indicates that the INP value is 8
11. nineSymbols (11) - Indicates that the INP value is 9
12. tenSymbols (12) - Indicates that the INP value is 10
13. elevenSymbols (13) - Indicates that the INP value is 11
14. twelveSymbols (14) - Indicates that the INP value is 12
15. thirteenSymbols (15) - Indicates that the INP value is 13
16. fourteenSymbols (16) - Indicates that the INP value is 14
17. fifteenSymbols (17) - Indicates that the INP value is 15
18. sixteenSymbols (18) - Indicates that the INP value is 16
19. invalidValue(-1) - Invalid valuerw Enumeration .1.3.6.1.2.1.10.94.1.1.65550.1.11 |
hwxdslDynamicProfCh1MinProtectionUsMinimum Impulse Noise Protection on Upstream direction. The
minimum impulse noise protection for the bearer channel,
expressed in symbols. The parameter can take the following
values: noProtection (i.e., INP not required), halfSymbol
(i.e., INP length is 1/2 symbol) and 1-16 symbols in steps
of 1 symbol.
Options:
1. noProtection (1) - Indicates that the INP value is 0
2. halfSymbol (2) - Indicates that the INP value is 0.5
3. singleSymbol (3) - Indicates that the INP value is 1
4. twoSymbols (4) - Indicates that the INP value is 2
5. threeSymbols (5) - Indicates that the INP value is 3
6. fourSymbols (6) - Indicates that the INP value is 4
7. fiveSymbols (7) - Indicates that the INP value is 5
8. sixSymbols (8) - Indicates that the INP value is 6
9. sevenSymbols (9) - Indicates that the INP value is 7
10. eightSymbols (10) - Indicates that the INP value is 8
11. nineSymbols (11) - Indicates that the INP value is 9
12. tenSymbols (12) - Indicates that the INP value is 10
13. elevenSymbols (13) - Indicates that the INP value is 11
14. twelveSymbols (14) - Indicates that the INP value is 12
15. thirteenSymbols (15) - Indicates that the INP value is 13
16. fourteenSymbols (16) - Indicates that the INP value is 14
17. fifteenSymbols (17) - Indicates that the INP value is 15
18. sixteenSymbols (18) - Indicates that the INP value is 16
19. invalidValue(-1) - Invalid valuerw Enumeration .1.3.6.1.2.1.10.94.1.1.65550.1.12 |
hwxdslDynamicProfCh1MaxDelayDsMaximum Interleave Delay on Downstream direction. The maximum
one-way interleaving delay introduced by the PMS-TC on
Downstream direction. The XTUs shall choose the S (factor) and
D (depth) values such that the actual one-way interleaving
delay is as close as possible to, but less than or equal to,
hwxdslDynamicProfCh1MaxDelayDs. The delay is coded in ms,
with the value 0 indicating no delay bound is being imposed.
Range: 0-200
Unit: millisecondsrw Unsigned32 .1.3.6.1.2.1.10.94.1.1.65550.1.13 |
hwxdslDynamicProfCh1MaxDelayUsMaximum Interleave Delay on Upstream direction. The maximum
one-way interleaving delay introduced by the PMS-TC on
Upstream direction. The XTUs shall choose the S (factor) and
D (depth) values such that the actual one-way interleaving
delay is as close as possible to, but less than or equal to,
hwxdslDynamicProfCh1MaxDelayUs. The delay is coded in ms,
with the value 0 indicating no delay bound is being imposed.
Range: 0-200
Unit: millisecondsrw Unsigned32 .1.3.6.1.2.1.10.94.1.1.65550.1.14 |
hwxdslDynamicProfCh2MinProtectionDsMinimum Impulse Noise Protection on Downstream direction. The
minimum impulse noise protection for the bearer channel,
expressed in symbols. The parameter can take the following
values: noProtection (i.e., INP not required), halfSymbol
(i.e., INP length is 1/2 symbol) and 1-16 symbols in steps
of 1 symbol.
Options:
1. noProtection (1) - Indicates that the INP value is 0
2. halfSymbol (2) - Indicates that the INP value is 0.5
3. singleSymbol (3) - Indicates that the INP value is 1
4. twoSymbols (4) - Indicates that the INP value is 2
5. threeSymbols (5) - Indicates that the INP value is 3
6. fourSymbols (6) - Indicates that the INP value is 4
7. fiveSymbols (7) - Indicates that the INP value is 5
8. sixSymbols (8) - Indicates that the INP value is 6
9. sevenSymbols (9) - Indicates that the INP value is 7
10. eightSymbols (10) - Indicates that the INP value is 8
11. nineSymbols (11) - Indicates that the INP value is 9
12. tenSymbols (12) - Indicates that the INP value is 10
13. elevenSymbols (13) - Indicates that the INP value is 11
14. twelveSymbols (14) - Indicates that the INP value is 12
15. thirteenSymbols (15) - Indicates that the INP value is 13
16. fourteenSymbols (16) - Indicates that the INP value is 14
17. fifteenSymbols (17) - Indicates that the INP value is 15
18. sixteenSymbols (18) - Indicates that the INP value is 16
19. invalidValue(-1) - Invalid valuerw Enumeration .1.3.6.1.2.1.10.94.1.1.65550.1.15 |
hwxdslDynamicProfCh2MinProtectionUsMinimum Impulse Noise Protection on Upstream direction. The
minimum impulse noise protection for the bearer channel,
expressed in symbols. The parameter can take the following
values: noProtection (i.e., INP not required), halfSymbol
(i.e., INP length is 1/2 symbol) and 1-16 symbols in steps
of 1 symbol.
Options:
1. noProtection (1) - Indicates that the INP value is 0
2. halfSymbol (2) - Indicates that the INP value is 0.5
3. singleSymbol (3) - Indicates that the INP value is 1
4. twoSymbols (4) - Indicates that the INP value is 2
5. threeSymbols (5) - Indicates that the INP value is 3
6. fourSymbols (6) - Indicates that the INP value is 4
7. fiveSymbols (7) - Indicates that the INP value is 5
8. sixSymbols (8) - Indicates that the INP value is 6
9. sevenSymbols (9) - Indicates that the INP value is 7
10. eightSymbols (10) - Indicates that the INP value is 8
11. nineSymbols (11) - Indicates that the INP value is 9
12. tenSymbols (12) - Indicates that the INP value is 10
13. elevenSymbols (13) - Indicates that the INP value is 11
14. twelveSymbols (14) - Indicates that the INP value is 12
15. thirteenSymbols (15) - Indicates that the INP value is 13
16. fourteenSymbols (16) - Indicates that the INP value is 14
17. fifteenSymbols (17) - Indicates that the INP value is 15
18. sixteenSymbols (18) - Indicates that the INP value is 16
19. invalidValue(-1) - Invalid valuerw Enumeration .1.3.6.1.2.1.10.94.1.1.65550.1.16 |
hwxdslDynamicProfCh2MaxDelayDsMaximum Interleave Delay on Downstream direction. The maximum
one-way interleaving delay introduced by the PMS-TC on
Downstream direction. The XTUs shall choose the S (factor) and
D (depth) values such that the actual one-way interleaving
delay is as close as possible to, but less than or equal to,
hwxdslDynamicProfCh2MaxDelayDs. The delay is coded in ms,
with the value 0 indicating no delay bound is being imposed.
Range: 0-200
Unit: millisecondsrw Unsigned32 .1.3.6.1.2.1.10.94.1.1.65550.1.17 |
hwxdslDynamicProfCh2MaxDelayUsMaximum Interleave Delay on Upstream direction. The maximum
one-way interleaving delay introduced by the PMS-TC on
Upstream direction. The XTUs shall choose the S (factor) and
D (depth) values such that the actual one-way interleaving
delay is as close as possible to, but less than or equal to,
hwxdslDynamicProfCh2MaxDelayUs. The delay is coded in ms,
with the value 0 indicating no delay bound is being imposed.
Range: 0-200
Unit: millisecondsrw Unsigned32 .1.3.6.1.2.1.10.94.1.1.65550.1.18 |
hwxdslDynamicProfPmModePower management state Enabling. Defines the power states the
xTU-C or xTU-R may autonomously transition to on this line.
The various bit positions are: allowTransitionsToIdle (0) and
allowTransitionsToLowPower (1). A bit with a '1' value means
that the xTU is allowed to transit into the respective state
and a '0' value means that the xTU is not allowed
to transit into the respective state.rw Bits .1.3.6.1.2.1.10.94.1.1.65550.1.19 |
hwxdslDynamicProfL0TimeThis minimum time (in seconds) between an Exit from the L2
state and the next Entry into the L2 state. It ranges from 0
to 255 seconds.
Range: 0-255rw Unsigned32 .1.3.6.1.2.1.10.94.1.1.65550.1.20 |
hwxdslDynamicProfL2TimeThis minimum time (in seconds) between an Entry into the
L2 state and the first Power Trim in the L2 state and between
two consecutive Power Trims in the L2 State.
It ranges from 0 to 255 seconds.
Range: 0-255rw Unsigned32 .1.3.6.1.2.1.10.94.1.1.65550.1.21 |
hwxdslDynamicProfL2AtprThe maximum aggregate transmit power reduction (in dB) that
can be performed at transition of L0 to L2 state or through a
single Power Trim in the L2 state.
It ranges from 0 dB to 31 dB.
Range: 0-31
Unit: dBrw Unsigned32 .1.3.6.1.2.1.10.94.1.1.65550.1.22 |
hwxdslDynamicProfL2AtprtThe total maximum aggregate transmit power reduction
(in dB) that can be performed in an L2 state. This is the
sum of all reductions of L2 Request (i.e., at transition of
L0 to L2 state) and Power Trims.
Range: 0-31
Unit: dBrw Unsigned32 .1.3.6.1.2.1.10.94.1.1.65550.1.23 |
hwxdslDynamicProfDpboEPsdThis parameter defines the PSD mask that is assumed to be permitted at the exchange.
This parameter shall use the same format as PSDMASKds. The maximum number of breakpoints
for DPBOEPSD is 16.
This is a string of 16 pairs of values in the following
structure:
Octets 0+1 - Index of 1st sub-carrier used in the context
of a first breakpoint.
Octet 2 - The PSD reduction for the sub-carrier indicated in
octets 0 and 1.
Octets 3-5 - Same, for a 2nd breakpoint.
Octets 6-8 - Same, for a 3rd breakpoint.
This architecture continues until octets 45-47, which are
associated with a 16th breakpoint.
Each subcarrier index is an unsigned number in the range 1 and
NSCds. Each PSD reduction value is in the range 0 (0dBm/Hz) to
255 (-127.5dBm/Hz) with steps of 0.5dBm/Hz. Valid values are
in the range 0 to 190 (0 to -95dBm/Hz).
When the number of breakpoints is less than 16, all remaining
octets are set to the value 0xff.rw OCTET STRING .1.3.6.1.2.1.10.94.1.1.65550.1.24 |
hwxdslDynamicProfDpboEsELThis configuration parameter defines the assumed electrical length of
cables (E-side cables) connecting exchange based DSL services to a remote
flexibility point (cabinet), that hosts the xTU-C that is subject to
spectrally shaped downstream power back-off depending on this length.
For this parameter the electrical length is defined as the loss (in dB)
of an equivalent length of hypothetical cable at a reference frequency
defined by the network operator or in spectrum management regulations.
DPBOESEL shall be coded as an unsigned integer representing an electrical
length from 0 dB (coded as 0) to 255.5 dB (coded as 511) in steps of 0.5 dB.
All values in the range are valid.If DPBOESEL is set to zero, the DPBO in
this section shall be disabled.
Range: 0-511
Unit: 0.5dBrw Unsigned32 .1.3.6.1.2.1.10.94.1.1.65550.1.25 |
hwxdslDynamicProfDpboEscmThis configuration parameter defines a cable model in terms of three scalars
DPBOESCMA, DPBOESCMB and DPBOESCMC that shall be used to describe the frequency
dependent loss of E-side cables.Parameters DPBOESCMA, DPBOESCMB, DPBOESCMC shall be
coded as unsigned integers representing a scalar value from -1 (coded as 0) to 1.5
(coded as 640) in step of 1/256. All values in the range are valid.
Octets 0+1 DPBOESCMA
Octets 2+3 DPBOESCMB
Octets 4+5 DPBOESCMCrw OCTET STRING .1.3.6.1.2.1.10.94.1.1.65550.1.26 |
hwxdslDynamicProfDpboMusDPBOMUS defines the assumed Minimum Usable receive Signal PSD (in dBm/Hz) for
exchange based services, used to modify parameter DPBOFMAX defined below. It
shall be coded as an unsigned integer representing a PSD level from 0 dBm/Hz
(coded as 0) to -127.5 dBm/Hz (coded as 255) in steps of 0.5 dBm/Hz.
All values in the range are valid.
Range: 0-255
Unit: 0.5dBm/Hzrw Unsigned32 .1.3.6.1.2.1.10.94.1.1.65550.1.27 |
hwxdslDynamicProfDpboFMinDPBOFMIN defines the minimum frequency from which the DPBO shall be applied.
It shall be coded as a 16 bits unsigned integer representing a frequency in
multiple of 4.3125 KHz. The range of valid values is from 0 kHz (coded as 0)
to 8832 kHz (coded as 2048).
Range: 0-2048
Unit: 4.3125 KHzrw Unsigned32 .1.3.6.1.2.1.10.94.1.1.65550.1.28 |
hwxdslDynamicProfDpboFMaxDPBOFMAX defines the maximum frequency at which DPBO may be applied. It shall be
coded as a 16 bits unsigned integer representing a frequency in multiple of 4.3125 KHz.
The range of valid values is from 138 kHz (coded as 32) to 29997.75 kHz (coded as 6956).
Range: 32-6956
Unit: 4.3125 KHzrw Unsigned32 .1.3.6.1.2.1.10.94.1.1.65550.1.29 |
hwxdslDynamicProfUpboPsdBandThis parameter defines the UPBO reference PSD used to compute the upstream power back-off
for each upstream band except US0. A UPBOPSD defined for each band ahsll consist of two
parameters [a, b]. Parameter a shall be coded as an unsigned 12-bit number from 40 dBm/Hz
(coded as 0) to 80.95 dBm/Hz (coded as 4095) in steps of 0.01 dBm/Hz; and b shall be coded
as an unsigned 12 bit number from 0 (coded as 0) to 40.95 dBm/Hz (coded as 4095) in steps
of 0.01 dBm/Hz. The UPBO reference PSD at the frequency f expressed in MHz shall be equal
to '-a-b(SQRT(f))'. The set of parameter values a = 40 dBm/Hz, b = 0 dBm/Hz is a special configuration
to disable UPBO in the respective upstream band.
Octets 0+1 - a[0]
Octets 2+3 - b[0]
Octets 4+5 - a[1]
Octets 6+7 - b[1]
Octets 8+9 - a[2]
Octets 10+11 - b[2]
Octets 12+13 - a[3]
Octets 14+15 - b[3]rw OCTET STRING .1.3.6.1.2.1.10.94.1.1.65550.1.30 |
hwxdslDynamicProfUpboKLFThis parameter is a flag that forces the VTU-R to use the electrical loop length of the CO-MIB
(UPBOKL) to compute the UPBO. The value shall be forced if the flag is set to 1. Otherwise, the
electrical loop length shall be autonomously selected by the VTU-O.
Options:
1. forced(1) - Force the CPE to use the electrical length of the CO(UPBOKL) to compute the UPBO
2. auto(2) - Electrical length shall be autonomously selected by the CO
3. invalidValue(-1) - Invalid valuerw Enumeration .1.3.6.1.2.1.10.94.1.1.65550.1.31 |
hwxdslDynamicProfUpboKLThis parameter defines the electrical loop length expressed in dB at 1MHz, kl0, configured by
the CO-MIB. The value shall be coded as an unsigned 16 bit number in the range 0 (coded as 0)
to 128 dB (coded as 1280) in steps of 0.1 dB.
Range: 0-1280
Unit: 0.1 dBrw Unsigned32 .1.3.6.1.2.1.10.94.1.1.65550.1.32 |
hwxdslDynamicProfRfiBandsThe subset of PSD mask breakpoints that shall be
used to notch an RFI band.
It is a string of bands consist of begin tone index
and end tone index.
for example :0-10,20-50,100-4095
It can contain as most as 16 bands.rw OCTET STRING .1.3.6.1.2.1.10.94.1.1.65550.1.33 |
hwxdslDynamicProfToneBlackOutThe subset of subcarriermask that shall be
used to mask the subcarriers.
It is a string of bands consist of begin tone index
and end tone index.
for example :0-10,20-50,100-4095
It can contain as most as 8 bands.rw OCTET STRING .1.3.6.1.2.1.10.94.1.1.65550.1.34 |
hwxdslDynamicProfCarMaskDSSub-carriers mask. A bitmap of 512 bits that allows masking
up to 512 downstream sub-carriers, depending on NSCds. If bit
i (0 <= i < NSCds) is set to '1', the respective
downstream sub-carrier i is masked, and if set to '0', the
respective sub-carrier is unmasked. Note that there should
always be unmasked sub-carriers (i.e., the object cannot be
all 1's). Also note that if NSCds < 512, all bits
i (NSCds i <= 512) should be set to '1'.rw OCTET STRING .1.3.6.1.2.1.10.94.1.1.65550.1.35 |
hwxdslDynamicProfCarMaskUSSub-carriers mask. A bitmap of 64 bits that allows masking
up to 64 downstream sub-carriers, depending on NSCds. If
bit i (0 <= i < NSCus) is set to '1', the respective
upstream sub-carrier i is masked, and if set to '0', the
respective sub-carrier is unmasked. Note that there
should always be unmasked sub-carriers (i.e., the object
cannot be all 1's). Also note that if NSCus <
64, all bits i (NSCus < i <= 64) should be set to '1'.rw OCTET STRING .1.3.6.1.2.1.10.94.1.1.65550.1.36 |
hwxdslDynamicProfXdslModeThe XDSL Mode is a way of categorizing the various XDSL
transmission modes into groups, each group (XDSL Mode) shares
the same PSD configuration.
Options:
1. defMode (1) - XDSL transmit mode is defMode
2. adsl (2) - XDSL transmit mode is adsl
3. adsl2Pots (3) - XDSL transmit mode is adsl2Pots
4. adsl2Isdn (4) - XDSL transmit mode is adsl2Isdn
5. adsl2PlusPots (5) - XDSL transmit mode is adsl2PlusPots
6. adsl2PlusIsdn (6) - XDSL transmit mode is adsl2PlusIsdn
7. adsl2ReachExtended (7) - XDSL transmit mode is adsl2ReachExtended
8. g9923PotsNonOverlapped(8) - XDSL transmit mode is g9923PotsNonOverlapped
9. g9923PotsOverlapped(9) - XDSL transmit mode is g9923PotsOverlapped
10. g9923IsdnNonOverlapped(10) - XDSL transmit mode is g9923IsdnNonOverlapped
11. g9923isdnOverlapped(11) - XDSL transmit mode is g9923isdnOverlapped
12. g9924potsNonOverlapped(14) - XDSL transmit mode is g9924potsNonOverlapped
13. g9924potsOverlapped(15) - XDSL transmit mode is g9924potsOverlapped
14. g9923AnnexIAllDigNonOverlapped(18) - XDSL transmit mode is g9923AnnexIAllDigNonOverlapped
15. g9923AnnexIAllDigOverlapped(19) - XDSL transmit mode is g9923AnnexIAllDigOverlapped
16. g9923AnnexJAllDigNonOverlapped(20) - XDSL transmit mode is g9923AnnexJAllDigNonOverlapped
17. g9923AnnexJAllDigOverlapped(21) - XDSL transmit mode is g9923AnnexJAllDigOverlapped
18. g9924AnnexIAllDigNonOverlapped(22) - XDSL transmit mode is g9924AnnexIAllDigNonOverlapped
19. g9924AnnexIAllDigOverlapped(23) - XDSL transmit mode is g9924AnnexIAllDigOverlapped
20. g9923AnnexLMode1NonOverlapped(24) - XDSL transmit mode is g9923AnnexLMode1NonOverlapped
21. g9923AnnexLMode2NonOverlapped(25) - XDSL transmit mode is g9923AnnexLMode2NonOverlapped
22. g9923AnnexLMode3Overlapped(26) - XDSL transmit mode is g9923AnnexLMode3Overlapped
23. g9923AnnexLMode4Overlapped(27) - XDSL transmit mode is g9923AnnexLMode4Overlapped
24. g9923AnnexMPotsNonOverlapped(28) - XDSL transmit mode is g9923AnnexMPotsNonOverlapped
25. g9923AnnexMPotsOverlapped(29) - XDSL transmit mode is g9923AnnexMPotsOverlapped
26. g9925PotsNonOverlapped(30) - XDSL transmit mode is g9925PotsNonOverlapped
27. g9925PotsOverlapped(31) - XDSL transmit mode is g9925PotsOverlapped
28. g9925IsdnNonOverlapped(32) - XDSL transmit mode is g9925IsdnNonOverlapped
29. g9925isdnOverlapped(33) - XDSL transmit mode is g9925isdnOverlapped
30. g9925AnnexIAllDigNonOverlapped(36) - XDSL transmit mode is g9925AnnexIAllDigNonOverlapped
31. g9925AnnexIAllDigOverlapped(37) - XDSL transmit mode is g9925AnnexIAllDigOverlapped
32. g9925AnnexJAllDigNonOverlapped(38) - XDSL transmit mode is g9925AnnexJAllDigNonOverlapped
33. g9925AnnexJAllDigOverlapped(39) - XDSL transmit mode is g9925AnnexJAllDigOverlapped
34. g9925AnnexMPotsNonOverlapped(40) - XDSL transmit mode is g9925AnnexMPotsNonOverlapped
35. g9925AnnexMPotsOverlapped(41) - XDSL transmit mode is g9925AnnexMPotsOverlapped
36. vdsl2Pots (42) - XDSL transmit mode is vdsl2Pots
37. vdsl2Isdn (43) - XDSL transmit mode is vdsl2Isdn
38. invalidValue(-1) - Invalid valuerw Enumeration .1.3.6.1.2.1.10.94.1.1.65550.1.37 |
hwxdslDynamicProfMaxNomPsdDsThe maximum nominal transmit PSD in the downstream
direction during initialization and Showtime. It ranges from
-600 to -300 units of 0.1 dBm/Hz(physical values are -60 to
-30 dBm/Hz). The invalid value is -1. If data is invalid, the invalid value will be returned.
Unit: 0.1 dBrw Integer32(-600..-300 | -1) UNITS "0.1 dB" .1.3.6.1.2.1.10.94.1.1.65550.1.38 |
hwxdslDynamicProfMaxNomPsdUsThe maximum nominal transmit PSD in the upstream
direction during initialization and Showtime. It ranges from
-600 to -300 units of 0.1 dBm/Hz(physical values are -60 to
-30 dBm/Hz). The invalid value is -1. If data is invalid, the invalid value will be returned.
Unit: 0.1 dBrw Integer32(-600..-300 | -1) UNITS "0.1 dB" .1.3.6.1.2.1.10.94.1.1.65550.1.39 |
hwxdslDynamicProfMaxNomAtpDsThe maximum nominal aggregate transmit power in the
downstream direction during initialization and Showtime. It
ranges from 0 to 255 units of 0.1 dBm (physical values are 0
to 25.5 dBm).
Range: 0-255
Unit: 0.1 dBmrw Unsigned32 .1.3.6.1.2.1.10.94.1.1.65550.1.40 |
hwxdslDynamicProfMaxNomAtpUsThe maximum nominal aggregate transmit power in the
upstream direction during initialization and Showtime. It
ranges from 0 to 255 units of 0.1 dBm (physical values are 0
to 25.5 dBm).
Range: 0-255
Unit: 0.1 dBmrw Unsigned32 .1.3.6.1.2.1.10.94.1.1.65550.1.41 |
hwxdslDynamicProfPsdMaskDsThis configuration parameter defines the downstream PSD mask
applicable at the U C2 reference point.
This MIB PSD mask may impose PSD restrictions in addition
to the Limit PSD mask defined in the relevant Recommendation
(e.g., G.992.5, G.993.2).
This is a string of 32 pairs of values in the following
structure:
Octets 0+1 - Index of 1st sub-carrier used in the context
of a first breakpoint.
Octet 2 - The PSD reduction for the sub-carrier indicated in
octets 0 and 1.
Octets 3-5 - Same, for a 2nd breakpoint.
Octets 6-8 - Same, for a 3rd breakpoint.
This architecture continues until octets 94-95, which are
associated with a 32nd breakpoint.
Each subcarrier index is an unsigned number in the range 0 and
(NSCds - 1). Each PSD reduction value is in the range 0 (0dBm/Hz) to
255 (-127.5dBm/Hz) with steps of 0.5dBm/Hz. Valid values are
in the range 0 to 190 (0 to -95dBm/Hz).
When the number of breakpoints is less than 32, all remaining
octets are set to the value 0xff. Note that the content of this
object should be correlated with the sub-carriers mask and with
the RFI setup.rw OCTET STRING .1.3.6.1.2.1.10.94.1.1.65550.1.42 |
hwxdslDynamicProfPsdMaskUsThis configuration parameter defines the upstream PSD
mask applicable at the U R2 reference point. This MIB
PSD mask may impose PSD restrictions in addition to the
Limit PSD mask defined in the relevant Recommendations
(e.g., ITU-T Recommendations G.992.3, G.993.2).
This is a string of 16 pairs of values in the following
structure:
Octets 0+1 - Index of 1st sub-carrier used in the context
of a first breakpoint.
Octet 2 - The PSD reduction for the sub-carrier indicated in
octets 0 and 1.
Octets 3-5 - Same, for a 2nd breakpoint.
Octets 45-47 - Same, for a 3rd breakpoint.
This architecture continues until octets 45-47, which are
associated with a 16th breakpoint.
Each subcarrier index is an unsigned number in the range 0 and
(NSCus - 1). Each PSD reduction value is in the range 0 (0dBm/Hz) to
255 (-127.5dBm/Hz) with steps of 0.5dBm/Hz. Valid values are
in the range 0 to 190 (0 to -95dBm/Hz).
When the number of breakpoints is less than 16, all remaining
octets are set to the value 0xff. Note that the content of this
object should be correlated with the sub-carriers mask and with
the RFI setup.rw OCTET STRING .1.3.6.1.2.1.10.94.1.1.65550.1.43 |
hwxdslDynamicProfLimitMaskThis configuration parameter contains the G.993.2
profiles to be allowed by the near-end xTU on this line.
Options:
1. profile8a (1) - The G.993.2 profile is profile8a
2. profile8b (2) - The G.993.2 profile is profile8b
3. profile8c (3) - The G.993.2 profile is profile8c
4. profile8d (4) - The G.993.2 profile is profile8d
5. profile12a (5) - The G.993.2 profile is profile12a
6. profile12b (6) - The G.993.2 profile is profile12b
7. profile17a (7) - The G.993.2 profile is profile17a
8. profile30a (8) - The G.993.2 profile is profile30a
9. invalidValue(-1) - Invalid valuerw Enumeration .1.3.6.1.2.1.10.94.1.1.65550.1.44 |
hwxdslDynamicProfClassMaskIn order to reduce the number of configuration possibilities,
the limit PSD masks are grouped in the following PSD mask classes:
Options:
1. annexA998-D-32(1) - Class 998 Annex A: D-32, D-64, D-48, D-128
2. annexA998-D-64(2) - Class 998 Annex A: D-32, D-64, D-48, D-128
3. annexB997-M1c-A-7(3) - Class 997-M1c Annex B: 997-M1c-A-7
4. annexB997-M1x-M-8(4) - Class 997-M1x Annex B: 997-M1x-M-8, 997-M1x-M
5. annexB997-M1x-M(5) - Class 997-M1x Annex B: 997-M1x-M-8, 997-M1x-M
6. annexB997-M2x-M-8(6) - Class 997-M2x Annex B: 997-M2x-M-8, 997-M2x-A, 997-M2x-M
7. annexB997-M2x-A(7) - Class 997-M2x Annex B: 997-M2x-M-8, 997-M2x-A, 997-M2x-M
8. annexB997-M2x-M(8) - Class 997-M2x Annex B: 997-M2x-M-8, 997-M2x-A, 997-M2x-M
9. annexB998-M1x-A(9) - Class 998-M1x Annex B: 998-M1x-A, 998-M1x-B, 998-M1x-NUS0
10. annexB998-M1x-B(10) - Class 998-M1x Annex B: 998-M1x-A, 998-M1x-B, 998-M1x-NUS0
11. annexB998-M1x-NUS0(11) - Class 998-M1x Annex B: 998-M1x-A, 998-M1x-B, 998-M1x-NUS0
12. annexB998-M2x-A(12) - Class 998-M2x Annex B: 998-M2x-A, 998-M2x-M, 998-M2x-B, 998-M2x-NUS0
13. annexB998-M2x-M(13) - Class 998-M2x Annex B: 998-M2x-A, 998-M2x-M, 998-M2x-B, 998-M2x-NUS0
14. annexB998-M2x-B(14) - Class 998-M2x Annex B: 998-M2x-A, 998-M2x-M, 998-M2x-B, 998-M2x-NUS0
15. annexB998-M2x-NUS0(15) - Class 998-M2x Annex B: 998-M2x-A, 998-M2x-M, 998-M2x-B, 998-M2x-NUS0
16. annexBHPE17-M1(16) - Class HPE17 Annex B: HPE17-M1
17. annexBHPE30-M1(17) - Class HPE30 Annex B: HPE30-M1
18. annexB997E17-M2x-A(18) - Class 997E17-M2x Annex B: 997E17-M2x-A
19. annexB997E30-M2x-NUS0(19) - Class 997E30-M2x Annex B: 997E30-M2x-NUS0
20. annexB998E17-M2x-NUS0(20) - Class 998E17-M2x Annex B: 998E17-M2x-NUS0, 998E17-M2x-NUS0-M
21. annexB998E17-M2x-NUS0-M(21) - Class 998E17-M2x Annex B: 998E17-M2x-NUS0, 998E17-M2x-NUS0-M
22. annexB998ADE17-M2x-NUS0-M(22) - Class 998ADE17-M2x Annex B: 998ADE17-M2x-NUS0-M, 998ADE17-M2x-A, 998ADE17-M2x-B, 998ADE17-M2x-M.
23. annexB998ADE17-M2x-B(23) - Class 998ADE17-M2x Annex B: 998ADE17-M2x-NUS0-M, 998ADE17-M2x-A, 998ADE17-M2x-B, 998ADE17-M2x-M.
24. annexB998E30-M2x-NUS0(24) - Class 998E30-M2x Annex B: 998E30-M2x-NUS0, 998E30-M2x-NUS0-M
25. annexB998E30-M2x-NUS0-M(25) - Class 998E30-M2x Annex B: 998E30-M2x-NUS0, 998E30-M2x-NUS0-M
26. annexB998ADE30-M2x-NUS0-M(26) - Class 998ADE30-M2x Annex B: 998ADE30-M2x-NUS0-M, 998ADE30-M2x-NUS0-A
27. annexB998ADE17-M2x-A(27) - Class 998ADE17-M2x Annex B: 998ADE17-M2x-NUS0-M, 998ADE17-M2x-A, 998ADE17-M2x-B, 998ADE17-M2x-M.
28. annexB998ADE30-M2x-NUS0-A(28) - Class 998ADE30-M2x Annex B: 998ADE30-M2x-NUS0-M, 998ADE30-M2x-NUS0-A
29. annexA998-D-48(29) - Class 998 Annex A: D-32, D-64, D-48, D-128
30. annexA998-D-128(30) - Class 998 Annex A: D-32, D-64, D-48, D-128
31. annexB998ADE17-M2x-M(31) - Class 998ADE17-M2x Annex B: 998ADE17-M2x-NUS0-M, 998ADE17-M2x-A, 998ADE17-M2x-B, 998ADE17-M2x-M.
32. invalidValue(-1) - Invalid valuerw Enumeration .1.3.6.1.2.1.10.94.1.1.65550.1.45 |
hwxdslDynamicProfBandOptUsageDefines the VDSL link use of the optional frequency
range [25kHz - 138kHz] (Opt).
Options:
1. disable(1) - Indicates Opt is unused
2. enable(2) - Indicates Opt usage is for upstream
3. invalidValue(-1) - Invalid value
Huawei defined.rw Enumeration .1.3.6.1.2.1.10.94.1.1.65550.1.46 |
hwxdslDynamicProfVirtualNoiseModeDsDefines the Virtual Noise of downsteam.
Options:
1. disable(1) - Unused
2. enable(2) - Used
3. invalidValue(-1) - Invalid valuerw Enumeration .1.3.6.1.2.1.10.94.1.1.65550.1.47 |
hwxdslDynamicProfVirtualNoiseModeUsDefines the Virtual Noise of upstream.
Options:
1. disable(1) - Unused
2. enable(2) - Used
3. invalidValue(-1) - Invalid valuerw Enumeration .1.3.6.1.2.1.10.94.1.1.65550.1.48 |
hwxdslDynamicProfVirtualNoiseDsThe Virtual Noise of downsteam.
This is a string of 32 pairs of values in the following
structure:
Octets 0+1 - Index of 1st sub-carrier used in the context
of a first breakpoint.
Octet 2 - The PSD reduction for the sub-carrier indicated in
octets 0 and 1.
Octets 3-5 - Same, for a 2nd breakpoint.
Octets 6-8 - Same, for a 3rd breakpoint.
This architecture continues until octets 94-95, which are
associated with a 32nd breakpoint.
Each subcarrier index is an unsigned number in the range 0 and
(NSCds - 1). Each PSD reduction value is in the range 0 (0dBm/Hz) to
255 (127.5dBm/Hz) with steps of 0.5dBm/Hz.rw OCTET STRING .1.3.6.1.2.1.10.94.1.1.65550.1.49 |
hwxdslDynamicProfVirtualNoiseUsThe Virtual Noise of upsteam.
This is a string of 16 pairs of values in the following
structure:
Octets 0+1 - Index of 1st sub-carrier used in the context
of a first breakpoint.
Octet 2 - The PSD reduction for the sub-carrier indicated in
octets 0 and 1.
Octets 3-5 - Same, for a 2nd breakpoint.
Octets 6-8 - Same, for a 3rd breakpoint.
This architecture continues until octets 45-47, which are
associated with a 16th breakpoint.
Each subcarrier index is an unsigned number in the range 0 and
(NSCds - 1). Each PSD reduction value is in the range 0 (0dBm/Hz) to
255 (127.5dBm/Hz) with steps of 0.5dBm/Hz.rw OCTET STRING .1.3.6.1.2.1.10.94.1.1.65550.1.50 |
hwxdslDynamicProfRowStatusThis object is used to create a new row or to modify or
delete an existing row in this table.
A profile is activated by setting this object to 'active'.
When 'active' is set, the system will validate the profile.
Before a profile can be deleted or taken out of service
(by setting this object to 'destroy' or 'outOfService'),
it must be first unreferenced from all associated
templates.rw RowStatus (SNMPv2-TC) .1.3.6.1.2.1.10.94.1.1.65550.1.51 |
hwXdslPortIopCaptureTableThe table hwXdslPortIopCaptureTable implement xDSL port IOP information capture.
The index of this table is ifIndex. SEQUENCE OF HwXdslPortIopCaptureEntry .1.3.6.1.2.1.10.94.1.1.65551 |
hwXdslPortIopCaptureEntryThe table hwXdslPortIopCaptureTable implement xDSL port IOP information capture.
The index of this entry is ifIndex. HwXdslPortIopCaptureEntry .1.3.6.1.2.1.10.94.1.1.65551.1 |
hwXdslPortIopCaptureOperTypeStart or stop IOP information capture of xDSL port.
Options:
1. start(1) - Start IOP information capture of xDSL port
2. stop(2) - Stop IOP information capture of xDSL port
3. invalid(-1) - Invalid valuerw Enumeration .1.3.6.1.2.1.10.94.1.1.65551.1.1 |
hwXdslPortIopCaptureOperStatusPort IOP capture status.
Options:
1. noCapture(1) - Indicates that the capture is not performed
2. capturing(2) - Indicates that the capture is being performed
3. iopGenerate(3) - Indicates that the IOP file is generated
4. captured(4) - Indicates that the capture is complete
5. invalid(-1) - Invalid valuero Enumeration .1.3.6.1.2.1.10.94.1.1.65551.1.2 |
hwXdslDynamicInfoCollectTableThe table hwXdslDynamicInfoCollectTable implement xDSL port Dynamic information collect.
The index of this table is hwFrameIndex and hwSlotIndex.deprecated SEQUENCE OF HwXdslDynamicInfoCollectEntry .1.3.6.1.2.1.10.94.1.1.65552 |
hwXdslDynamicInfoCollectEntryThe table hwXdslDynamicInfoCollectTable implement xDSL port Dynamic information collect.
The index of this entry is hwFrameIndex and hwSlotIndex.deprecated HwXdslDynamicInfoCollectEntry .1.3.6.1.2.1.10.94.1.1.65552.1 |
hwXdslDynamicInfoCollectStart Dynamic information collecting of Xdsl port.
Options:
1. start(1) - Indicates that collecting data starts
2. invalid(-1) - Invalid valuerwdeprecated Enumeration .1.3.6.1.2.1.10.94.1.1.65552.1.1 |
hwXdslDynamicInfoCollectStatusBoard Dynamic information collecting status.
Options:
1. noCollect(1) - Indicates that collecting data is not performed
2. collecting(2) - Indicates that collecting data is being performed
3. collected(3) - Indicates that collecting data is completerodeprecated Enumeration .1.3.6.1.2.1.10.94.1.1.65552.1.2 |
hwXdslDynamicInfoCollectTimeTime when collecting the optimization information is complete.rodeprecated DateAndTime (SNMPv2-TC) .1.3.6.1.2.1.10.94.1.1.65552.1.3 |
hwAdslTraps OBJECT IDENTIFIER .1.3.6.1.2.1.10.94.1.2.65536 |
hwAdslGeneralTraps OBJECT IDENTIFIER .1.3.6.1.2.1.10.94.1.2.65536.1 |
hwAdslGeneralTrapsOIDs OBJECT IDENTIFIER .1.3.6.1.2.1.10.94.1.2.65536.1.0 |
hwAdslPortActRateMonitorTrapDefinition of the trap reported when the ADSL port rate fails to meet the requirement.
If ADSL act rate is lower than threshold, hwTrapType is 1. Otherwise, hwTrapType is 2. NOTIFICATION-TYPE .1.3.6.1.2.1.10.94.1.2.65536.1.0.1 |
hwAdslPortRateChangeTrapADSL act rate is change trap.
This trap message is generated when the ADSL port rate change. NOTIFICATION-TYPE .1.3.6.1.2.1.10.94.1.2.65536.1.0.2 |
hwadsl2LineTransAtucActualThe actual transmission mode of the ATU-C.
During ADSL line initialization, the ADSL
Transceiver Unit - Remote terminal end (ATU-R)
will determine the mode used for the link.
This value will be limited a single transmission
mode that is a subset of those modes enabled
by the ATU-C and denoted by
adslLineTransAtucConfig. After an initialization
has occurred, its mode is saved as the 'Current'
mode and is persistence should the link go
down. This object returns 0 (i.e. BITS with no
mode bit set) if the mode is not known.ro Adsl2TransmissionModeType (ADSL2-LINE-TC-MIB) .1.3.6.1.2.1.10.94.3.1.17.1.65555 |
hwAdslThis MIB is used for defining Huawei's ADSL management MIB objects. MODULE-IDENTITY .1.3.6.1.4.1.2011.6.31 |