ADSL-LINE-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for ADSL-LINE-MIB.
276
Objects
Active
Status
8
Dependencies
Imported Objects
Objects
276 total| Object Name |
|---|
adslMIB OBJECT IDENTIFIER .1.3.6.1.2.1.10.94 |
RFC1155-SMI Unknown .1.3.6.1.2.1.10.94 |
adslLineMib OBJECT IDENTIFIER .1.3.6.1.2.1.10.94.1 |
adslMibObjects OBJECT IDENTIFIER .1.3.6.1.2.1.10.94.1.1 |
adslLineTableThis table includes common attributes describing
both ends of the line. It is required for all ADSL
physical interfaces. ADSL physical interfaces are
those ifEntries where ifType is equal to adsl(94). SEQUENCE OF AdslLineEntry .1.3.6.1.2.1.10.94.1.1.1 |
adslLineEntryAn entry in adslLineTable. AdslLineEntry .1.3.6.1.2.1.10.94.1.1.1.1 |
adslLineCodingSpecifies the ADSL coding type used on this line.
Other types may be added in the future.ro Enumeration .1.3.6.1.2.1.10.94.1.1.1.1.1 |
adslLineTypeDefines the type of ADSL physical line
entity that exists, by defining whether and how
the line is channelized. If the line is channelized,
the value will be other than noChannel(1). This
object defines which channel type(s) are supported.
In the case that the line is channelized, the manager
can use the ifStackTable to determine the ifIndex for
the associated channel(s).ro Enumeration .1.3.6.1.2.1.10.94.1.1.1.1.2 |
adslLineSpecificOID instance in vendor-specific MIB. The Instance may
be used to determine shelf/slot/port of the ATUC
interface in a DSLAM.ro VariablePointer -- Rsyntax OBJECT IDENTIFIER .1.3.6.1.2.1.10.94.1.1.1.1.3 |
adslLineConfProfileThe value of this object identifies the row
in the ADSL Line Configuration Profile Table,
(adslLineConfProfileTable), which applies for this
ADSL line, and channels if applicable.
For `dynamic' mode, in the case which the
configuration profile has not been set, the
value will be set to `DEFVAL'.
If the implementator of this MIB has chosen not
to implement `dynamic assignment' of profiles, this
object's MIN-ACCESS is read-only.rw AdslLineProfileName -- Rsyntax OCTET STRING .1.3.6.1.2.1.10.94.1.1.1.1.4 |
adslLineAlarmConfProfileThe value of this object identifies the row
in the ADSL Line Alarm Configuration Profile Table,
(adslLineAlarmConfProfileTable), which applies to this
ADSL line, and channels if applicable.
For `dynamic' mode, in the case which the
alarm profile has not been set, the
value will be set to `DEFVAL'.
If the implementator of this MIB has chosen not
to implement `dynamic assignment' of profiles, this
object's MIN-ACCESS is read-only.rw AdslLineProfileName -- Rsyntax OCTET STRING .1.3.6.1.2.1.10.94.1.1.1.1.5 |
adslAtucPhysTableThis table provides one row for each ATUC.
Each row contains the Physical Layer Parameters
table for that ATUC. ADSL physical interfaces are
those ifEntries where ifType is equal to adsl(94). SEQUENCE OF AdslAtucPhysEntry .1.3.6.1.2.1.10.94.1.1.2 |
adslAtucPhysEntryAn entry in the adslAtucPhysTable. AdslAtucPhysEntry .1.3.6.1.2.1.10.94.1.1.2.1 |
adslAtucInvSerialNumberVendor specific string that identifies the vendor
equipment.ro OCTET STRING .1.3.6.1.2.1.10.94.1.1.2.1.1 |
adslAtucInvVendorIDThe vendor ID assigned by T1E1.413 according to its
Annex D.[10]ro OCTET STRING .1.3.6.1.2.1.10.94.1.1.2.1.2 |
adslAtucInvVersionNumberVendor specific version number sent by this ATU as
part of the initialization messages.ro OCTET STRING .1.3.6.1.2.1.10.94.1.1.2.1.3 |
adslAtucCurrSnrMgnNoise Margin as seen by this ATU with respect to its
received signal in tenth dB.ro Gauge .1.3.6.1.2.1.10.94.1.1.2.1.4 |
adslAtucCurrAtnMeasured difference in the total power transmitted by
the peer ATU and the total power received by this ATU.
This value is determined in accordance with
T1.413[10].ro Gauge .1.3.6.1.2.1.10.94.1.1.2.1.5 |
adslAtucCurrStatusIndicates current state of the ATUC line. This is a
bit-map of possible conditions. The various bit
positions are:
0 noDefect There no defects on the line
1 lossOfFraming ATUC failure due to not
receiving valid frame.
2 lossOfSignal ATUC failure due to not
receiving signal.
3 lossOfPower ATUC failure due to loss of
power.
Note: the Agent may still
function.
4 lossOfSignalQuality Loss of Signal Quality is
declared when the Noise Margin
falls below the Minimum Noise
Margin, or the bit-error-rate
exceeds 10^-7.
5 lossOfLink ATUC failure due to inability
to link with ATUR.
6 dataInitFailure ATUC failure during
initialization due to bit
errors corrupting startup
exchange data.
7 configInitFailure ATUC failure during
initialization due to peer
ATU not able to support
requested configuration
8 protocolInitFailure ATUC failure during
initialization due to
incompatible protocol used by
the peer ATU.
9 noPeerAtuPresent ATUC failure during
initialization due to no
activation sequence detected
from peer ATU.
This is intended to supplement ifOperStatus.ro OCTET STRING .1.3.6.1.2.1.10.94.1.1.2.1.6 |
adslAtucCurrOutputPwrMeasured total output power transmitted by this ATU.
This is the measurement that was reported during
the last activation sequence.ro Gauge .1.3.6.1.2.1.10.94.1.1.2.1.7 |
adslAtucCurrAttainableRateIndicates the maximum currently attainable data rate
by the ATU. This value will be equal or greater than
the current line rate.ro Gauge -- Units -- bps .1.3.6.1.2.1.10.94.1.1.2.1.8 |
adslAturPhysTableThis table provides one row for each ATUR
Each row contains the Physical Layer Parameters
table for that ATUR. ADSL physical interfaces are
those ifEntries where ifType is equal to adsl(94). SEQUENCE OF AdslAturPhysEntry .1.3.6.1.2.1.10.94.1.1.3 |
adslAturPhysEntryAn entry in the adslAturPhysTable. AdslAturPhysEntry .1.3.6.1.2.1.10.94.1.1.3.1 |
adslAturInvSerialNumberVendor specific string that identifies the vendor
equipment.ro OCTET STRING .1.3.6.1.2.1.10.94.1.1.3.1.1 |
adslAturInvVendorIDThe vendor ID assigned by T1E1.413 according to its
Annex D.ro OCTET STRING .1.3.6.1.2.1.10.94.1.1.3.1.2 |
adslAturInvVersionNumberVendor specific version number sent by this ATU as
part of the initialization messages.ro OCTET STRING .1.3.6.1.2.1.10.94.1.1.3.1.3 |
adslAturCurrSnrMgnNoise Margin as seen by this ATU with respect to its
received signal. This value is determined in
accordance with T1.413 [10].ro Gauge .1.3.6.1.2.1.10.94.1.1.3.1.4 |
adslAturCurrAtnMeasured difference in the total power transmitted by
the peer ATU and the total power received by this ATU.
This value is determined in accordance with
T1.413[10].ro Gauge .1.3.6.1.2.1.10.94.1.1.3.1.5 |
adslAturCurrStatusIndicates current state of the ATUR line. This is a
bit-map of possible conditions. Due to the isolation
of the ATUR when line problems occur, many state
conditions like loss of power, loss of quality signal,
and initialization errors, can not be determined.
While trouble shooting ATUR, also use object,
adslAtucCurrStatus. The various bit positions are:
0 noDefect There no defects on the line
1 lossOfFraming ATUR failure due to not
receiving valid frame
2 lossOfSignal ATUR failure due to not
receiving signal
3 lossOfPower ATUR failure due to loss of
power
4 lossOfSignalQuality Loss of Signal Quality is
declared when the Noise Margin
falls below the Minimum Noise
Margin, or the
bit-error-rate exceeds 10^-7.
This is intended to supplement ifOperStatus.ro OCTET STRING .1.3.6.1.2.1.10.94.1.1.3.1.6 |
adslAturCurrOutputPwrMeasured total output power transmitted by this ATU.
This is the measurement that was reported during
the last activation sequence.ro Gauge .1.3.6.1.2.1.10.94.1.1.3.1.7 |
adslAturCurrAttainableRateIndicates the maximum currently attainable data rate
by the ATU. This value will be equal or greater than
the current line rate.ro Gauge -- Units -- bps .1.3.6.1.2.1.10.94.1.1.3.1.8 |
adslAtucChanTableThis table provides one row for each ATUC channel.
ADSL channel interfaces are those ifEntries
where ifType is equal to adslInterleave(124)
or adslFast(125). SEQUENCE OF AdslAtucChanEntry .1.3.6.1.2.1.10.94.1.1.4 |
adslAtucChanEntryAn entry in the adslAtucChanTable. AdslAtucChanEntry .1.3.6.1.2.1.10.94.1.1.4.1 |
adslAtucChanInterleaveDelayInterleave Delay for this channel.
Interleave delay applies only to the
interleave channel and defines the mapping
(relative spacing) between subsequent input
bytes at the interleaver input and their placement
in the bit stream at the interleaver output.
Larger numbers provide greater separation between
consecutive input bytes in the output bit stream
allowing for improved impulse noise immunity at
the expense of payload latency.
In the case where the ifType is Fast(125), use
noSuchObject.ro Gauge -- Units -- milli-seconds .1.3.6.1.2.1.10.94.1.1.4.1.1 |
adslAtucChanCurrTxRateActual transmit rate on this channel.ro Gauge -- Units -- bps .1.3.6.1.2.1.10.94.1.1.4.1.2 |
adslAtucChanPrevTxRateThe rate at the time of the last
adslAtucRateChangeTrap event. It is also set at
initialization to prevent a trap being sent.
Rate changes less than adslAtucThresh(*)RateDown
or less than adslAtucThresh(*)RateUp will not
cause a trap or cause this object to change.
(*) == Fast or Interleave.
See AdslLineAlarmConfProfileEntry.ro Gauge -- Units -- bps .1.3.6.1.2.1.10.94.1.1.4.1.3 |
adslAtucChanCrcBlockLengthIndicates the length of the channel data-block
on which the CRC operates. Refer to Line Code
Specific MIBs, [11] and [12] for more
information.ro Gauge -- Units -- byte .1.3.6.1.2.1.10.94.1.1.4.1.4 |
adslAturChanTableThis table provides one row for each ATUR channel.
ADSL channel interfaces are those ifEntries
where ifType is equal to adslInterleave(124)
or adslFast(125). SEQUENCE OF AdslAturChanEntry .1.3.6.1.2.1.10.94.1.1.5 |
adslAturChanEntryAn entry in the adslAturChanTable. AdslAturChanEntry .1.3.6.1.2.1.10.94.1.1.5.1 |
adslAturChanInterleaveDelayInterleave Delay for this channel.
Interleave delay applies only to the
interleave channel and defines the mapping
(relative spacing) between subsequent input
bytes at the interleaver input and their placement
in the bit stream at the interleaver output.
Larger numbers provide greater separation between
consecutive input bytes in the output bit stream
allowing for improved impulse noise immunity at
the expense of payload latency.
In the case where the ifType is Fast(125), use
noSuchObject.ro Gauge -- Units -- milli-seconds .1.3.6.1.2.1.10.94.1.1.5.1.1 |
adslAturChanCurrTxRateActual transmit rate on this channel.ro Gauge -- Units -- bps .1.3.6.1.2.1.10.94.1.1.5.1.2 |
adslAturChanPrevTxRateThe rate at the time of the last
adslAturRateChangeTrap event. It is also set at
initialization to prevent a trap being sent.
Rate changes less than adslAturThresh(*)RateDown
or less than adslAturThresh(*)RateUp will not
cause a trap or cause this object to change.
(*) == Fast or Interleave.
See AdslLineAlarmConfProfileEntry.ro Gauge -- Units -- bps .1.3.6.1.2.1.10.94.1.1.5.1.3 |
adslAturChanCrcBlockLengthIndicates the length of the channel data-block
on which the CRC operates. Refer to Line Code
Specific MIBs, [11] and [12] for more
information.ro Gauge .1.3.6.1.2.1.10.94.1.1.5.1.4 |
adslAtucPerfDataTableThis table provides one row for each ATUC.
ADSL physical interfaces are
those ifEntries where ifType is equal to adsl(94). SEQUENCE OF AdslAtucPerfDataEntry .1.3.6.1.2.1.10.94.1.1.6 |
adslAtucPerfDataEntryAn entry in adslAtucPerfDataTable. AdslAtucPerfDataEntry .1.3.6.1.2.1.10.94.1.1.6.1 |
adslAtucPerfLofsCount of the number of Loss of Framing failures since
agent reset.ro Counter .1.3.6.1.2.1.10.94.1.1.6.1.1 |
adslAtucPerfLossCount of the number of Loss of Signal failures since
agent reset.ro Counter .1.3.6.1.2.1.10.94.1.1.6.1.2 |
adslAtucPerfLolsCount of the number of Loss of Link failures since
agent reset.ro Counter .1.3.6.1.2.1.10.94.1.1.6.1.3 |
adslAtucPerfLprsCount of the number of Loss of Power failures since
agent reset.ro Counter .1.3.6.1.2.1.10.94.1.1.6.1.4 |
adslAtucPerfESsCount of the number of Errored Seconds since agent
reset. The errored second parameter is a count of
one-second intervals containing one or more crc
anomalies, or one or more los or sef defects.ro Counter .1.3.6.1.2.1.10.94.1.1.6.1.5 |
adslAtucPerfInitsCount of the line initialization attempts since
agent reset. Includes both successful and failed
attempts.ro Counter .1.3.6.1.2.1.10.94.1.1.6.1.6 |
adslAtucPerfValidIntervalsNumber of previous 15-minute intervals in the
adslAtucInterval Table for which valid data
has been stored. This value will be equal to the
maximum # of intervals that are kept (n) unless the
device was brought online within the last (nx15)
minutes. In the case where the agent is a proxy,
it is possible that some intervals are unavailable.
In this case, this interval is the maximum interval
for which valid data is available.ro INTEGER .1.3.6.1.2.1.10.94.1.1.6.1.7 |
adslAtucPerfInvalidIntervalsThe number of 15 minute intervals in which no valid
data is available.ro INTEGER .1.3.6.1.2.1.10.94.1.1.6.1.8 |
adslAtucPerfCurr15MinTimeElapsedTotal elapsed seconds in this interval.
A full interval is 900 seconds.ro PerfCurrentCount -- Rsyntax Gauge -- Units -- seconds .1.3.6.1.2.1.10.94.1.1.6.1.9 |
adslAtucPerfCurr15MinLofsCount of seconds in the current 15 minute interval
when there was Loss of Framing.ro PerfCurrentCount -- Rsyntax Gauge -- Units -- seconds .1.3.6.1.2.1.10.94.1.1.6.1.10 |
adslAtucPerfCurr15MinLossCount of seconds in the current 15 minute interval
when there was Loss of Signal.ro PerfCurrentCount -- Rsyntax Gauge -- Units -- seconds .1.3.6.1.2.1.10.94.1.1.6.1.11 |
adslAtucPerfCurr15MinLolsCount of seconds in the current 15 minute interval
when there was Loss of Link.ro PerfCurrentCount -- Rsyntax Gauge -- Units -- seconds .1.3.6.1.2.1.10.94.1.1.6.1.12 |
adslAtucPerfCurr15MinLprsCount of seconds in the current 15 minute interval
when there was Loss of Power.ro PerfCurrentCount -- Rsyntax Gauge -- Units -- seconds .1.3.6.1.2.1.10.94.1.1.6.1.13 |
adslAtucPerfCurr15MinESsCount of Errored Seconds in the current 15 minute
interval. The errored second parameter is a count of
one-second intervals containing one or more crc
anomalies, or one or more los or sef defects.ro PerfCurrentCount -- Rsyntax Gauge -- Units -- seconds .1.3.6.1.2.1.10.94.1.1.6.1.14 |
adslAtucPerfCurr15MinInitsCount of the line initialization attempts in the
current 15 minute interval. Includes both successful
and failed attempts.ro PerfCurrentCount -- Rsyntax Gauge .1.3.6.1.2.1.10.94.1.1.6.1.15 |
adslAtucPerfCurr1DayTimeElapsedNumber of seconds that have elapsed since the
beginning of the current 1-day interval.ro INTEGER .1.3.6.1.2.1.10.94.1.1.6.1.16 |
adslAtucPerfCurr1DayLofsCount of the number of seconds when there was Loss of
Framing during the current day as measured by
adslAtucPerfCurr1DayTimeElapsed.ro Gauge -- Units -- seconds .1.3.6.1.2.1.10.94.1.1.6.1.17 |
adslAtucPerfCurr1DayLossCount of the number of seconds when there was Loss of
Signal during the current day as measured by
adslAtucPerfCurr1DayTimeElapsed.ro Gauge -- Units -- seconds .1.3.6.1.2.1.10.94.1.1.6.1.18 |
adslAtucPerfCurr1DayLolsCount of the number of seconds when there was Loss of
Link during the current day as measured by
adslAtucPerfCurr1DayTimeElapsed.ro Gauge -- Units -- seconds .1.3.6.1.2.1.10.94.1.1.6.1.19 |
adslAtucPerfCurr1DayLprsCount of the number of seconds when there was Loss of
Power during the current day as measured by
adslAtucPerfCurr1DayTimeElapsed.ro Gauge -- Units -- seconds .1.3.6.1.2.1.10.94.1.1.6.1.20 |
adslAtucPerfCurr1DayESsCount of Errored Seconds during the current day as
measured by adslAtucPerfCurr1DayTimeElapsed.
The errored second parameter is a count of
one-second intervals containing one or more crc
anomalies, or one or more los or sef defects.ro Gauge -- Units -- seconds .1.3.6.1.2.1.10.94.1.1.6.1.21 |
adslAtucPerfCurr1DayInitsCount of the line initialization attempts in the
day as measured by adslAtucPerfCurr1DayTimeElapsed.
Includes both successful and failed attempts.ro Gauge .1.3.6.1.2.1.10.94.1.1.6.1.22 |
adslAtucPerfPrev1DayMoniSecsThe time in the previous 1-day interval over which
the performance monitoring information is actually
counted. This value will normally be the same as the
total interval duration except in a situation where
performance monitoring data can not be collected
for any reason. Typically Elapsed 1-day time will be
copied into Monitored Seconds when the 1-day roll-over
occurs.ro INTEGER .1.3.6.1.2.1.10.94.1.1.6.1.23 |
adslAtucPerfPrev1DayLofsCount of seconds in the interval when there was
Loss of Framing within the most recent previous
1-day period.ro Gauge -- Units -- seconds .1.3.6.1.2.1.10.94.1.1.6.1.24 |
adslAtucPerfPrev1DayLossCount of seconds in the interval when there was
Loss of Signal within the most recent previous
1-day period.ro Gauge -- Units -- seconds .1.3.6.1.2.1.10.94.1.1.6.1.25 |
adslAtucPerfPrev1DayLolsCount of seconds in the interval when there was
Loss of Link within the most recent previous
1-day period.ro Gauge -- Units -- seconds .1.3.6.1.2.1.10.94.1.1.6.1.26 |
adslAtucPerfPrev1DayLprsCount of seconds in the interval when there was
Loss of Power within the most recent previous
1-day period.ro Gauge -- Units -- seconds .1.3.6.1.2.1.10.94.1.1.6.1.27 |
adslAtucPerfPrev1DayESsCount of Errored Seconds within the most recent
previous 1-day period. The errored second parameter is
a count of one-second intervals containing one or more
crc anomalies, or one or more los or sef defects.ro Gauge -- Units -- seconds .1.3.6.1.2.1.10.94.1.1.6.1.28 |
adslAtucPerfPrev1DayInitsCount of the line initialization attempts in the most
recent previous 1-day period. Includes both successful
and failed attempts.ro Gauge .1.3.6.1.2.1.10.94.1.1.6.1.29 |
adslAturPerfDataTableThis table provides one row for each ATUR.
ADSL physical interfaces are
those ifEntries where ifType is equal to adsl(94). SEQUENCE OF AdslAturPerfDataEntry .1.3.6.1.2.1.10.94.1.1.7 |
adslAturPerfDataEntryAn entry in adslAturPerfDataTable. AdslAturPerfDataEntry .1.3.6.1.2.1.10.94.1.1.7.1 |
adslAturPerfLofsCount of the number of Loss of Framing failures since
agent reset.ro Counter -- Units -- seconds .1.3.6.1.2.1.10.94.1.1.7.1.1 |
adslAturPerfLossCount of the number of Loss of Signal failures since
agent reset.ro Counter -- Units -- seconds .1.3.6.1.2.1.10.94.1.1.7.1.2 |
adslAturPerfLprsCount of the number of Loss of Power failures since
agent reset.ro Counter -- Units -- seconds .1.3.6.1.2.1.10.94.1.1.7.1.3 |
adslAturPerfESsCount of the number of Errored Seconds since agent
reset. The errored second parameter is a count of
one-second intervals containing one or more crc
anomalies, or one or more los or sef defects.ro Counter -- Units -- seconds .1.3.6.1.2.1.10.94.1.1.7.1.4 |
adslAturPerfValidIntervalsNumber of previous 15-minute intervals in the
adslAturInterval Table for which valid data
has been stored. This value will be equal to the
maximum # of intervals that are kept (n) unless the
device was brought online within the last (nx15) min.
In the case where the agent is a proxy, it is possible
that some intervals are unavailable. In this case, this
interval is the maximum interval for which valid data
is available.ro INTEGER .1.3.6.1.2.1.10.94.1.1.7.1.5 |
adslAturPerfInvalidIntervalsThe number of 15 minute intervals in which no valid
data is available.ro INTEGER .1.3.6.1.2.1.10.94.1.1.7.1.6 |
adslAturPerfCurr15MinTimeElapsedTotal elapsed seconds in this interval.
A full interval is 900 seconds.ro PerfCurrentCount -- Rsyntax Gauge -- Units -- seconds .1.3.6.1.2.1.10.94.1.1.7.1.7 |
adslAturPerfCurr15MinLofsCount of seconds in the current 15 minute interval
when there was Loss of Framing.ro PerfCurrentCount -- Rsyntax Gauge -- Units -- seconds .1.3.6.1.2.1.10.94.1.1.7.1.8 |
adslAturPerfCurr15MinLossCount of seconds in the current 15 minute interval
when there was Loss of Signal.ro PerfCurrentCount -- Rsyntax Gauge -- Units -- seconds .1.3.6.1.2.1.10.94.1.1.7.1.9 |
adslAturPerfCurr15MinLprsCount of seconds in the current 15 minute interval
when there was Loss of Power.ro PerfCurrentCount -- Rsyntax Gauge -- Units -- seconds .1.3.6.1.2.1.10.94.1.1.7.1.10 |
adslAturPerfCurr15MinESsCount of Errored Seconds in the current 15 minute
interval. The errored second parameter is a count of
one-second intervals containing one or more crc
anomalies, or one or more los or sef defects.ro PerfCurrentCount -- Rsyntax Gauge -- Units -- seconds .1.3.6.1.2.1.10.94.1.1.7.1.11 |
adslAturPerfCurr1DayTimeElapsedNumber of seconds that have elapsed since the
beginning of the current 1-day interval.ro INTEGER .1.3.6.1.2.1.10.94.1.1.7.1.12 |
adslAturPerfCurr1DayLofsCount of the number of seconds when there was Loss
of Framing during the current day as measured by
adslAturPerfCurr1DayTimeElapsed.ro Gauge -- Units -- seconds .1.3.6.1.2.1.10.94.1.1.7.1.13 |
adslAturPerfCurr1DayLossCount of the number of seconds when there was Loss
of Signal during the current day as measured by
adslAturPerfCurr1DayTimeElapsed.ro Gauge -- Units -- seconds .1.3.6.1.2.1.10.94.1.1.7.1.14 |
adslAturPerfCurr1DayLprsCount of the number of seconds when there was Loss
of Power during the current day as measured by
adslAturPerfCurr1DayTimeElapsed.ro Gauge -- Units -- seconds .1.3.6.1.2.1.10.94.1.1.7.1.15 |
adslAturPerfCurr1DayESsCount of Errored Seconds during the current day as
measured by adslAturPerfCurr1DayTimeElapsed.
The errored second parameter is a count of
one-second intervals containing one or more crc
anomalies, or one or more los or sef defects.ro Gauge -- Units -- seconds .1.3.6.1.2.1.10.94.1.1.7.1.16 |
adslAturPerfPrev1DayMoniSecsThe time in the previous 1-day interval over which
the performance monitoring information is actually
counted. This value will normally be the same as the
total interval duration except in a situation where
performance monitoring data can not be collected
for any reason. Typically Elapsed 1-day time will be
copied into Monitored Seconds when the 1-day roll-over
occurs.ro INTEGER .1.3.6.1.2.1.10.94.1.1.7.1.17 |
adslAturPerfPrev1DayLofsCount of seconds in the interval when there was
Loss of Framing within the most recent previous
1-day period.ro Gauge -- Units -- seconds .1.3.6.1.2.1.10.94.1.1.7.1.18 |
adslAturPerfPrev1DayLossCount of seconds in the interval when there was
Loss of Signal within the most recent previous
1-day period.ro Gauge -- Units -- seconds .1.3.6.1.2.1.10.94.1.1.7.1.19 |
adslAturPerfPrev1DayLprsCount of seconds in the interval when there was
Loss of Power within the most recent previous
1-day period.ro Gauge -- Units -- seconds .1.3.6.1.2.1.10.94.1.1.7.1.20 |
adslAturPerfPrev1DayESsCount of Errored Seconds within the most recent
previous 1-day period. The errored second parameter is
a count of one-second intervals containing one or more
crc anomalies, or one or more los or sef defects.ro Gauge -- Units -- seconds .1.3.6.1.2.1.10.94.1.1.7.1.21 |
adslAtucIntervalTableThis table provides one row for each ATUC
performance data collection interval.
ADSL physical interfaces are
those ifEntries where ifType is equal to adsl(94). SEQUENCE OF AdslAtucIntervalEntry .1.3.6.1.2.1.10.94.1.1.8 |
adslAtucIntervalEntryAn entry in the adslAtucIntervalTable. AdslAtucIntervalEntry .1.3.6.1.2.1.10.94.1.1.8.1 |
adslAtucIntervalNumberPerformance Data Interval number 1 is the
the most recent previous interval; interval
96 is 24 hours ago. Intervals 2..96 are
optional. INTEGER .1.3.6.1.2.1.10.94.1.1.8.1.1 |
adslAtucIntervalLofsCount of seconds in the interval when there was Loss
of Framing.ro PerfIntervalCount -- Rsyntax Gauge -- Units -- seconds .1.3.6.1.2.1.10.94.1.1.8.1.2 |
adslAtucIntervalLossCount of seconds in the interval when there was Loss
of Signal.ro PerfIntervalCount -- Rsyntax Gauge -- Units -- seconds .1.3.6.1.2.1.10.94.1.1.8.1.3 |
adslAtucIntervalLolsCount of seconds in the interval when there was Loss
of Link.ro PerfIntervalCount -- Rsyntax Gauge -- Units -- seconds .1.3.6.1.2.1.10.94.1.1.8.1.4 |
adslAtucIntervalLprsCount of seconds in the interval when there was Loss
of Power.ro PerfIntervalCount -- Rsyntax Gauge -- Units -- seconds .1.3.6.1.2.1.10.94.1.1.8.1.5 |
adslAtucIntervalESsCount of Errored Seconds in the interval.
The errored second parameter is a count of
one-second intervals containing one or more crc
anomalies, or one or more los or sef defects.ro PerfIntervalCount -- Rsyntax Gauge -- Units -- seconds .1.3.6.1.2.1.10.94.1.1.8.1.6 |
adslAtucIntervalInitsCount of the line initialization attempts
during the interval. Includes both successful
and failed attempts.ro PerfIntervalCount -- Rsyntax Gauge .1.3.6.1.2.1.10.94.1.1.8.1.7 |
adslAtucIntervalValidDataThis object indicates if there is valid data
for this interval.ro TruthValue -- Rsyntax INTEGER { -- true(1), -- false(2) -- } .1.3.6.1.2.1.10.94.1.1.8.1.8 |
adslAturIntervalTableThis table provides one row for each ATUR
performance data collection interval.
ADSL physical interfaces are those
ifEntries where ifType is equal to adsl(94). SEQUENCE OF AdslAturIntervalEntry .1.3.6.1.2.1.10.94.1.1.9 |
adslAturIntervalEntryAn entry in the adslAturIntervalTable. AdslAturIntervalEntry .1.3.6.1.2.1.10.94.1.1.9.1 |
adslAturIntervalNumberPerformance Data Interval number 1 is the
the most recent previous interval; interval
96 is 24 hours ago. Intervals 2..96 are
optional. INTEGER .1.3.6.1.2.1.10.94.1.1.9.1.1 |
adslAturIntervalLofsCount of seconds in the interval when there was
Loss of Framing.ro PerfIntervalCount -- Rsyntax Gauge -- Units -- seconds .1.3.6.1.2.1.10.94.1.1.9.1.2 |
adslAturIntervalLossCount of seconds in the interval when there was
Loss of Signal.ro PerfIntervalCount -- Rsyntax Gauge -- Units -- seconds .1.3.6.1.2.1.10.94.1.1.9.1.3 |
adslAturIntervalLprsCount of seconds in the interval when there was
Loss of Power.ro PerfIntervalCount -- Rsyntax Gauge -- Units -- seconds .1.3.6.1.2.1.10.94.1.1.9.1.4 |
adslAturIntervalESsCount of Errored Seconds in the interval.
The errored second parameter is a count of
one-second intervals containing one or more crc
anomalies, or one or more los or sef defects.ro PerfIntervalCount -- Rsyntax Gauge -- Units -- seconds .1.3.6.1.2.1.10.94.1.1.9.1.5 |
adslAturIntervalValidDataThis object indicates if there is valid data
for this interval.ro TruthValue -- Rsyntax INTEGER { -- true(1), -- false(2) -- } .1.3.6.1.2.1.10.94.1.1.9.1.6 |
adslAtucChanPerfDataTableThis table provides one row for each ATUC channel.
ADSL channel interfaces are those ifEntries
where ifType is equal to adslInterleave(124)
or adslFast(125). SEQUENCE OF AdslAtucChanPerfDataEntry .1.3.6.1.2.1.10.94.1.1.10 |
adslAtucChanPerfDataEntryAn entry in adslAtucChanPerfDataTable. AdslAtucChanPerfDataEntry .1.3.6.1.2.1.10.94.1.1.10.1 |
adslAtucChanReceivedBlksCount of all encoded blocks received on this channel
since agent reset.ro Counter .1.3.6.1.2.1.10.94.1.1.10.1.1 |
adslAtucChanTransmittedBlksCount of all encoded blocks transmitted on this
channel since agent reset.ro Counter .1.3.6.1.2.1.10.94.1.1.10.1.2 |
adslAtucChanCorrectedBlksCount of all blocks received with errors that were
corrected since agent reset. These blocks are passed
on as good data.ro Counter .1.3.6.1.2.1.10.94.1.1.10.1.3 |
adslAtucChanUncorrectBlksCount of all blocks received with uncorrectable
errors since agent reset.ro Counter .1.3.6.1.2.1.10.94.1.1.10.1.4 |
adslAtucChanPerfValidIntervalsNumber of previous 15-minute intervals in the
adslAtucChanIntervalTable Table for which valid data
has been stored. This value will be equal to the max
number of intervals that are kept (n) unless the device
was brought online within the last (nx15) minutes. In
the case where the agent is a proxy, it is possible
that some intervals are unavailable. In this case,
this interval is the maximum interval for which valid
data is available.ro INTEGER .1.3.6.1.2.1.10.94.1.1.10.1.5 |
adslAtucChanPerfInvalidIntervalsThe number of 15 minute intervals in which no valid
data is available.ro INTEGER .1.3.6.1.2.1.10.94.1.1.10.1.6 |
adslAtucChanPerfCurr15MinTimeElapsedTotal elapsed seconds in this interval.
A full interval is 900 seconds.ro PerfCurrentCount -- Rsyntax Gauge -- Units -- seconds .1.3.6.1.2.1.10.94.1.1.10.1.7 |
adslAtucChanPerfCurr15MinReceivedBlksCount of all encoded blocks received on this channel
within the current 15 minute interval.ro PerfCurrentCount -- Rsyntax Gauge .1.3.6.1.2.1.10.94.1.1.10.1.8 |
adslAtucChanPerfCurr15MinTransmittedBlksCount of all encoded blocks transmitted on this
channel within the current 15 minute interval.ro PerfCurrentCount -- Rsyntax Gauge .1.3.6.1.2.1.10.94.1.1.10.1.9 |
adslAtucChanPerfCurr15MinCorrectedBlksCount of all blocks received with errors that were
corrected on this channel within the current 15 minute
interval.ro PerfCurrentCount -- Rsyntax Gauge .1.3.6.1.2.1.10.94.1.1.10.1.10 |
adslAtucChanPerfCurr15MinUncorrectBlksCount of all blocks received with uncorrectable
errors on this channel within the current 15 minute
interval.ro PerfCurrentCount -- Rsyntax Gauge .1.3.6.1.2.1.10.94.1.1.10.1.11 |
adslAtucChanPerfCurr1DayTimeElapsedNumber of seconds that have elapsed since the
beginning of the current 1-day interval.ro INTEGER .1.3.6.1.2.1.10.94.1.1.10.1.12 |
adslAtucChanPerfCurr1DayReceivedBlksCount of all encoded blocks received on this
channel during the current day as measured by
adslAtucChanPerfCurr1DayTimeElapsed.ro Gauge .1.3.6.1.2.1.10.94.1.1.10.1.13 |
adslAtucChanPerfCurr1DayTransmittedBlksCount of all encoded blocks transmitted on this
channel during the current day as measured by
adslAtucChanPerfCurr1DayTimeElapsed.ro Gauge .1.3.6.1.2.1.10.94.1.1.10.1.14 |
adslAtucChanPerfCurr1DayCorrectedBlksCount of all blocks received with errors that were
corrected on this channel during the current day as
measured by adslAtucChanPerfCurr1DayTimeElapsed.ro Gauge .1.3.6.1.2.1.10.94.1.1.10.1.15 |
adslAtucChanPerfCurr1DayUncorrectBlksCount of all blocks received with uncorrectable
errors on this channel during the current day as
measured by adslAtucChanPerfCurr1DayTimeElapsed.ro Gauge .1.3.6.1.2.1.10.94.1.1.10.1.16 |
adslAtucChanPerfPrev1DayMoniSecsThe time in the previous 1-day interval over which
the performance monitoring information is actually
counted. This value will normally be the same as the
total interval duration except in a situation where
performance monitoring information can not be collected
for any reason. Typically Elapsed 1-day time will be
copied into Monitored Seconds when the 1-day roll-over
occurs.ro INTEGER .1.3.6.1.2.1.10.94.1.1.10.1.17 |
adslAtucChanPerfPrev1DayReceivedBlksCount of all encoded blocks received on this
channel within the most recent previous 1-day
period.ro Gauge .1.3.6.1.2.1.10.94.1.1.10.1.18 |
adslAtucChanPerfPrev1DayTransmittedBlksCount of all encoded blocks transmitted on this
channel within the most recent previous 1-day
period.ro Gauge .1.3.6.1.2.1.10.94.1.1.10.1.19 |
adslAtucChanPerfPrev1DayCorrectedBlksCount of all blocks received with errors that were
corrected on this channel within the most recent
previous 1-day period.ro Gauge .1.3.6.1.2.1.10.94.1.1.10.1.20 |
adslAtucChanPerfPrev1DayUncorrectBlksCount of all blocks received with uncorrectable
errors on this channel within the most recent previous
1-day period.ro Gauge .1.3.6.1.2.1.10.94.1.1.10.1.21 |
adslAturChanPerfDataTableThis table provides one row for each ATUR channel.
ADSL channel interfaces are those ifEntries
where ifType is equal to adslInterleave(124)
or adslFast(125). SEQUENCE OF AdslAturChanPerfDataEntry .1.3.6.1.2.1.10.94.1.1.11 |
adslAturChanPerfDataEntryAn entry in adslAturChanPerfDataTable. AdslAturChanPerfDataEntry .1.3.6.1.2.1.10.94.1.1.11.1 |
adslAturChanReceivedBlksCount of all encoded blocks received on this channel
since agent reset.ro Counter .1.3.6.1.2.1.10.94.1.1.11.1.1 |
adslAturChanTransmittedBlksCount of all encoded blocks transmitted on this
channel since agent reset.ro Counter .1.3.6.1.2.1.10.94.1.1.11.1.2 |
adslAturChanCorrectedBlksCount of all blocks received with errors that were
corrected since agent reset. These blocks are passed
on as good data.ro Counter .1.3.6.1.2.1.10.94.1.1.11.1.3 |
adslAturChanUncorrectBlksCount of all blocks received with uncorrectable
errors since agent reset.ro Counter .1.3.6.1.2.1.10.94.1.1.11.1.4 |
adslAturChanPerfValidIntervalsNumber of previous 15-minute intervals in the
adslAturChanIntervalTable Table for which valid data
has been stored. This value will be equal to the
max # of intervals that are kept (n) unless the device
was brought online within the last (nx15) minutes. In
the case where the agent is a proxy, it is possible
that some intervals are unavailable. In this case,
this interval is the maximum interval for which valid
data is available.ro INTEGER .1.3.6.1.2.1.10.94.1.1.11.1.5 |
adslAturChanPerfInvalidIntervalsThe number of 15 minute intervals in which no valid
data is available.ro INTEGER .1.3.6.1.2.1.10.94.1.1.11.1.6 |
adslAturChanPerfCurr15MinTimeElapsedTotal elapsed seconds in this interval.
A full interval is 900 seconds.ro PerfCurrentCount -- Rsyntax Gauge -- Units -- seconds .1.3.6.1.2.1.10.94.1.1.11.1.7 |
adslAturChanPerfCurr15MinReceivedBlksCount of all encoded blocks received on this
channel within the current 15 minute interval.ro PerfCurrentCount -- Rsyntax Gauge .1.3.6.1.2.1.10.94.1.1.11.1.8 |
adslAturChanPerfCurr15MinTransmittedBlksCount of all encoded blocks transmitted on this
channel within the current 15 minute interval.ro PerfCurrentCount -- Rsyntax Gauge .1.3.6.1.2.1.10.94.1.1.11.1.9 |
adslAturChanPerfCurr15MinCorrectedBlksCount of all blocks received with errors that were
corrected on this channel within the current 15 minute
interval.ro PerfCurrentCount -- Rsyntax Gauge .1.3.6.1.2.1.10.94.1.1.11.1.10 |
adslAturChanPerfCurr15MinUncorrectBlksCount of all blocks received with uncorrectable
errors on this channel within the current 15 minute
interval.ro PerfCurrentCount -- Rsyntax Gauge .1.3.6.1.2.1.10.94.1.1.11.1.11 |
adslAturChanPerfCurr1DayTimeElapsedNumber of seconds that have elapsed since the
beginning of the current 1-day interval.ro INTEGER .1.3.6.1.2.1.10.94.1.1.11.1.12 |
adslAturChanPerfCurr1DayReceivedBlksCount of all encoded blocks received on this
channel during the current day as measured by
adslAturChanPerfCurr1DayTimeElapsed.ro Gauge .1.3.6.1.2.1.10.94.1.1.11.1.13 |
adslAturChanPerfCurr1DayTransmittedBlksCount of all encoded blocks transmitted on this
channel during the current day as measured by
adslAturChanPerfCurr1DayTimeElapsed.ro Gauge .1.3.6.1.2.1.10.94.1.1.11.1.14 |
adslAturChanPerfCurr1DayCorrectedBlksCount of all blocks received with errors that were
corrected on this channel during the current day as
measured by adslAturChanPerfCurr1DayTimeElapsed.ro Gauge .1.3.6.1.2.1.10.94.1.1.11.1.15 |
adslAturChanPerfCurr1DayUncorrectBlksCount of all blocks received with uncorrectable
errors on this channel during the current day as
measured by adslAturChanPerfCurr1DayTimeElapsed.ro Gauge .1.3.6.1.2.1.10.94.1.1.11.1.16 |
adslAturChanPerfPrev1DayMoniSecsThe time in the previous 1-day interval over which
the performance monitoring information is actually
counted. This value will normally be the same as the
total interval duration except in a situation where
performance monitoring information can not be collected
for any reason. Typically Elapsed 1-day time will be
copied into Monitored Seconds when the 1-day roll-over
occurs.ro INTEGER .1.3.6.1.2.1.10.94.1.1.11.1.17 |
adslAturChanPerfPrev1DayReceivedBlksCount of all encoded blocks received on this
channel within the most recent previous 1-day
period.ro Gauge .1.3.6.1.2.1.10.94.1.1.11.1.18 |
adslAturChanPerfPrev1DayTransmittedBlksCount of all encoded blocks transmitted on this
channel within the most recent previous 1-day
period.ro Gauge .1.3.6.1.2.1.10.94.1.1.11.1.19 |
adslAturChanPerfPrev1DayCorrectedBlksCount of all blocks received with errors that were
corrected on this channel within the most recent
previous 1-day period.ro Gauge .1.3.6.1.2.1.10.94.1.1.11.1.20 |
adslAturChanPerfPrev1DayUncorrectBlksCount of all blocks received with uncorrectable
errors on this channel within the most recent previous
1-day period.ro Gauge .1.3.6.1.2.1.10.94.1.1.11.1.21 |
adslAtucChanIntervalTableThis table provides one row for each ATUC channel's
performance data collection interval.
ADSL channel interfaces are those ifEntries
where ifType is equal to adslInterleave(124)
or adslFast(125). SEQUENCE OF AdslAtucChanIntervalEntry .1.3.6.1.2.1.10.94.1.1.12 |
adslAtucChanIntervalEntryAn entry in the adslAtucIntervalTable. AdslAtucChanIntervalEntry .1.3.6.1.2.1.10.94.1.1.12.1 |
adslAtucChanIntervalNumberPerformance Data Interval number 1 is the
the most recent previous interval; interval
96 is 24 hours ago. Intervals 2..96 are
optional. INTEGER .1.3.6.1.2.1.10.94.1.1.12.1.1 |
adslAtucChanIntervalReceivedBlksCount of all encoded blocks received on this channel
during this interval.ro PerfIntervalCount -- Rsyntax Gauge .1.3.6.1.2.1.10.94.1.1.12.1.2 |
adslAtucChanIntervalTransmittedBlksCount of all encoded blocks transmitted on this
channel during this interval.ro PerfIntervalCount -- Rsyntax Gauge .1.3.6.1.2.1.10.94.1.1.12.1.3 |
adslAtucChanIntervalCorrectedBlksCount of all blocks received with errors that were
corrected on this channel during this interval.ro PerfIntervalCount -- Rsyntax Gauge .1.3.6.1.2.1.10.94.1.1.12.1.4 |
adslAtucChanIntervalUncorrectBlksCount of all blocks received with uncorrectable
errors on this channel during this interval.ro PerfIntervalCount -- Rsyntax Gauge .1.3.6.1.2.1.10.94.1.1.12.1.5 |
adslAtucChanIntervalValidDataThis object indicates if there is valid data
for this interval.ro TruthValue -- Rsyntax INTEGER { -- true(1), -- false(2) -- } .1.3.6.1.2.1.10.94.1.1.12.1.6 |
adslAturChanIntervalTableThis table provides one row for each ATUR channel's
performance data collection interval.
ADSL channel interfaces are those ifEntries
where ifType is equal to adslInterleave(124)
or adslFast(125). SEQUENCE OF AdslAturChanIntervalEntry .1.3.6.1.2.1.10.94.1.1.13 |
adslAturChanIntervalEntryAn entry in the adslAturIntervalTable. AdslAturChanIntervalEntry .1.3.6.1.2.1.10.94.1.1.13.1 |
adslAturChanIntervalNumberPerformance Data Interval number 1 is the
the most recent previous interval; interval
96 is 24 hours ago. Intervals 2..96 are
optional. INTEGER .1.3.6.1.2.1.10.94.1.1.13.1.1 |
adslAturChanIntervalReceivedBlksCount of all encoded blocks received on this channel
during this interval.ro PerfIntervalCount -- Rsyntax Gauge .1.3.6.1.2.1.10.94.1.1.13.1.2 |
adslAturChanIntervalTransmittedBlksCount of all encoded blocks transmitted on this
channel during this interval.ro PerfIntervalCount -- Rsyntax Gauge .1.3.6.1.2.1.10.94.1.1.13.1.3 |
adslAturChanIntervalCorrectedBlksCount of all blocks received with errors that were
corrected on this channel during this interval.ro PerfIntervalCount -- Rsyntax Gauge .1.3.6.1.2.1.10.94.1.1.13.1.4 |
adslAturChanIntervalUncorrectBlksCount of all blocks received with uncorrectable
errors on this channel during this interval.ro PerfIntervalCount -- Rsyntax Gauge .1.3.6.1.2.1.10.94.1.1.13.1.5 |
adslAturChanIntervalValidDataThis object indicates if there is valid data
for this interval.ro TruthValue -- Rsyntax INTEGER { -- true(1), -- false(2) -- } .1.3.6.1.2.1.10.94.1.1.13.1.6 |
adslLineConfProfileTableThis table contains information on the ADSL line
configuration. One entry in this table reflects a
profile defined by a manager which can be used to
configure the ADSL line. SEQUENCE OF AdslLineConfProfileEntry .1.3.6.1.2.1.10.94.1.1.14 |
adslLineConfProfileEntryEach entry consists of a list of parameters that
represents the configuration of an ADSL modem.
When `dynamic' profiles are implemented, a
profile is created in one step with all necessary
parameter values and adslLineProfileRowStatus set to
createAndGo. This RowStatus object is also used
to destroy profiles.
Also when `dynamic' profiles are implemented, a default
profile will always exist. This profile's name will
be set to `DEFVAL' and its parameters will be set to
vendor specific values, unless otherwise specified
in this document.
When `static' profiles are implemented, profiles
are automically created or destroyed as ADSL
physical lines are discovered and removed by
the system. The name of the profile will be
equivalent to the decimal value of the line's
interface index. AdslLineConfProfileEntry .1.3.6.1.2.1.10.94.1.1.14.1 |
adslLineConfProfileNameThis object is used by the line configuration table
in order to identify a row of this table.
When `dynamic' profiles are implemented, the profile
name is user specified. Also, the system will always
provide a default profile whose name is `DEFVAL'.
When `static' profiles are implemented, there is an
one-to-one relationship between each line and its
profile. In which case, the profile name will
need to algorithmicly represent the Line's ifIndex.
Therefore, the profile's name is a decimalized string
of the ifIndex that is fixed-length (i.e., 10) with
leading zero(s). For example, the profile name for
ifIndex which equals '15' will be '0000000015'. AdslLineProfileName -- Rsyntax OCTET STRING .1.3.6.1.2.1.10.94.1.1.14.1.1 |
adslAtucConfRateModeDefines what form of transmit rate adaptation is
configured on this modem. See ADSL Forum TR-005 [3]
for more information.rw Enumeration .1.3.6.1.2.1.10.94.1.1.14.1.2 |
adslAtucConfRateChanRatioConfigured allocation ratio of excess transmit
bandwidth between fast and interleaved channels. Only
applies when two channel mode and RADSL are supported.
Distribute bandwidth on each channel in excess of the
corresponding ChanConfMinTxRate so that:
adslAtucConfRateChanRatio =
[Fast / (Fast + Interleaved)] * 100
In other words this value is the fast channel
percentage.rw INTEGER .1.3.6.1.2.1.10.94.1.1.14.1.3 |
adslAtucConfTargetSnrMgnConfigured Target Signal/Noise Margin.
This is the Noise Margin the modem must achieve
with a BER of 10-7 or better to successfully complete
initialization.rw INTEGER .1.3.6.1.2.1.10.94.1.1.14.1.4 |
adslAtucConfMaxSnrMgnConfigured Maximum acceptable Signal/Noise Margin.
If the Noise Margin is above this the modem should
attempt to reduce its power output to optimize its
operation.rw INTEGER .1.3.6.1.2.1.10.94.1.1.14.1.5 |
adslAtucConfMinSnrMgnConfigured Minimum acceptable Signal/Noise Margin.
If the noise margin falls below this level, the modem
should attempt to increase its power output. If that
is not possible the modem will attempt to
re-initialize or shut down.rw INTEGER .1.3.6.1.2.1.10.94.1.1.14.1.6 |
adslAtucConfDownshiftSnrMgnConfigured Signal/Noise Margin for rate downshift.
If the noise margin falls below this level, the modem
should attempt to decrease its transmit rate. In
the case that RADSL is not present, the value will
be `0'.rw INTEGER .1.3.6.1.2.1.10.94.1.1.14.1.7 |
adslAtucConfUpshiftSnrMgnConfigured Signal/Noise Margin for rate upshift.
If the noise margin rises above this level, the modem
should attempt to increase its transmit rate. In
the case that RADSL is not present, the value will
be `0'.rw INTEGER .1.3.6.1.2.1.10.94.1.1.14.1.8 |
adslAtucConfMinUpshiftTimeMinimum time that the current margin is above
UpshiftSnrMgn before an upshift occurs.
In the case that RADSL is not present, the value will
be `0'.rw INTEGER .1.3.6.1.2.1.10.94.1.1.14.1.9 |
adslAtucConfMinDownshiftTimeMinimum time that the current margin is below
DownshiftSnrMgn before a downshift occurs.
In the case that RADSL is not present, the value will
be `0'.rw INTEGER .1.3.6.1.2.1.10.94.1.1.14.1.10 |
adslAtucChanConfFastMinTxRateConfigured Minimum Transmit rate for `Fast' channels,
in bps. See adslAtucConfRateChanRatio for information
regarding RADSL mode and ATUR transmit rate for
ATUC receive rates.rw INTEGER -- Units -- bps .1.3.6.1.2.1.10.94.1.1.14.1.11 |
adslAtucChanConfInterleaveMinTxRateConfigured Minimum Transmit rate for `Interleave'
channels, in bps. See adslAtucConfRateChanRatio for
information regarding RADSL mode and see
ATUR transmit rate for receive rates.rw INTEGER -- Units -- bps .1.3.6.1.2.1.10.94.1.1.14.1.12 |
adslAtucChanConfFastMaxTxRateConfigured Maximum Transmit rate for `Fast' channels,
in bps. See adslAtucConfRateChanRatio for information
regarding RADSL mode and see ATUR transmit rate for
ATUC receive rates.rw INTEGER -- Units -- bps .1.3.6.1.2.1.10.94.1.1.14.1.13 |
adslAtucChanConfInterleaveMaxTxRateConfigured Maximum Transmit rate for `Interleave'
channels, in bps. See adslAtucConfRateChanRatio for
information regarding RADSL mode and ATUR transmit
rate for ATUC receive rates.rw INTEGER -- Units -- bps .1.3.6.1.2.1.10.94.1.1.14.1.14 |
adslAtucChanConfMaxInterleaveDelayConfigured maximum Interleave Delay for this channel.
Interleave delay applies only to the interleave channel
and defines the mapping (relative spacing) between
subsequent input bytes at the interleaver input and
their placement in the bit stream at the interleaver
output. Larger numbers provide greater separation
between consecutive input bytes in the output bit
stream allowing for improved impulse noise immunity
at the expense of payload latency.rw INTEGER .1.3.6.1.2.1.10.94.1.1.14.1.15 |
adslAturConfRateModeDefines what form of transmit rate adaptation is
configured on this modem. See ADSL Forum TR-005 [3]
for more information.rw Enumeration .1.3.6.1.2.1.10.94.1.1.14.1.16 |
adslAturConfRateChanRatioConfigured allocation ratio of excess transmit
bandwidth between fast and interleaved channels. Only
applies when two channel mode and RADSL are supported.
Distribute bandwidth on each channel in excess of the
corresponding ChanConfMinTxRate so that:
adslAturConfRateChanRatio =
[Fast / (Fast + Interleaved)] * 100
In other words this value is the fast channel
percentage.rw INTEGER .1.3.6.1.2.1.10.94.1.1.14.1.17 |
adslAturConfTargetSnrMgnConfigured Target Signal/Noise Margin.
This is the Noise Margin the modem must achieve
with a BER of 10-7 or better to successfully complete
initialization.rw INTEGER .1.3.6.1.2.1.10.94.1.1.14.1.18 |
adslAturConfMaxSnrMgnConfigured Maximum acceptable Signal/Noise Margin.
If the Noise Margin is above this the modem should
attempt to reduce its power output to optimize its
operation.rw INTEGER .1.3.6.1.2.1.10.94.1.1.14.1.19 |
adslAturConfMinSnrMgnConfigured Minimum acceptable Signal/Noise Margin.
If the noise margin falls below this level, the modem
should attempt to increase its power output. If that
is not possible the modem will attempt to
re-initialize or shut down.rw INTEGER .1.3.6.1.2.1.10.94.1.1.14.1.20 |
adslAturConfDownshiftSnrMgnConfigured Signal/Noise Margin for rate downshift.
If the noise margin falls below this level, the modem
should attempt to decrease its transmit rate. In
the case that RADSL is not present,
the value will be `0'.rw INTEGER .1.3.6.1.2.1.10.94.1.1.14.1.21 |
adslAturConfUpshiftSnrMgnConfigured Signal/Noise Margin for rate upshift.
If the noise margin rises above this level, the modem
should attempt to increase its transmit rate.
In the case that RADSL is not present,
the value will be `0'.rw INTEGER .1.3.6.1.2.1.10.94.1.1.14.1.22 |
adslAturConfMinUpshiftTimeMinimum time that the current margin is above
UpshiftSnrMgn before an upshift occurs.
In the case that RADSL is not present, the value will
be `0'.rw INTEGER .1.3.6.1.2.1.10.94.1.1.14.1.23 |
adslAturConfMinDownshiftTimeMinimum time that the current margin is below
DownshiftSnrMgn before a downshift occurs.
In the case that RADSL is not present, the value will
be `0'.rw INTEGER .1.3.6.1.2.1.10.94.1.1.14.1.24 |
adslAturChanConfFastMinTxRateConfigured Minimum Transmit rate for `Fast' channels,
in bps. See adslAturConfRateChanRatio for information
regarding RADSL mode and ATUC transmit rate
for ATUR receive rates.rw INTEGER -- Units -- bps .1.3.6.1.2.1.10.94.1.1.14.1.25 |
adslAturChanConfInterleaveMinTxRateConfigured Minimum Transmit rate for `Interleave'
channels, in bps. See adslAturConfRateChanRatio for
information regarding RADSL mode and ATUC transmit rate
for ATUR receive rates.rw INTEGER -- Units -- bps .1.3.6.1.2.1.10.94.1.1.14.1.26 |
adslAturChanConfFastMaxTxRateConfigured Maximum Transmit rate for `Fast' channels,
in bps. See adslAturConfRateChanRatio for information
regarding RADSL mode and ATUC transmit rate
for ATUR receive rates.rw INTEGER -- Units -- bps .1.3.6.1.2.1.10.94.1.1.14.1.27 |
adslAturChanConfInterleaveMaxTxRateConfigured Maximum Transmit rate for `Interleave'
channels, in bps. See adslAturConfRateChanRatio for
information regarding RADSL mode and see
ATUC transmit rate for ATUR receive rates.rw INTEGER -- Units -- bps .1.3.6.1.2.1.10.94.1.1.14.1.28 |
adslAturChanConfMaxInterleaveDelayConfigured maximum Interleave Delay for this channel.
Interleave delay applies only to the interleave channel
and defines the mapping (relative spacing) between
subsequent input bytes at the interleaver input and
their placement in the bit stream at the interleaver
output. Larger numbers provide greater separation
between consecutive input bytes in the output bit
stream allowing for improved impulse noise immunity
at the expense of payload latency.rw INTEGER .1.3.6.1.2.1.10.94.1.1.14.1.29 |
adslLineConfProfileRowStatusThis object is used to create a new row or modify or
delete an existing row in this table.
A profile activated by setting this object to
`active'. When `active' is set, the system
will validate the profile.
Before a profile can be deleted or taken out of
service, (by setting this object to `destroy' or
`outOfService') it must be first unreferenced
from all associated lines.
If the implementator of this MIB has chosen not
to implement `dynamic assignment' of profiles, this
object's MIN-ACCESS is read-only and its value
is always to be `active'.rw RowStatus -- Rsyntax INTEGER { -- active(1), -- notInService(2), -- notReady(3), -- createAndGo(4), -- createAndWait(5), -- destroy(6) -- } .1.3.6.1.2.1.10.94.1.1.14.1.30 |
adslLineAlarmConfProfileTableThis table contains information on the ADSL line
configuration. One entry in this table reflects a
profile defined by a manager which can be used to
configure the modem for a physical line SEQUENCE OF AdslLineAlarmConfProfileEntry .1.3.6.1.2.1.10.94.1.1.15 |
adslLineAlarmConfProfileEntryEach entry consists of a list of parameters that
represents the configuration of an ADSL modem.
When `dynamic' profiles are implemented, a
profile is created in one step with all necessary
parameter values and adslLineProfileRowStatus set to
createAndGo. This RowStatus object is also used
to destroy profiles.
Also when `dynamic' profiles are implemented, a default
profile will always exist. This profile's name will
be set to `DEFVAL' and its parameters will be set to
vendor specific values, unless otherwise specified
in this document.
When `static' profiles are implemented, profiles
are automically created or destroyed as ADSL
physical lines are discovered and removed by
the system. The name of the profile will be
equivalent to the decimal value of the line's
interface index. AdslLineAlarmConfProfileEntry .1.3.6.1.2.1.10.94.1.1.15.1 |
adslLineAlarmConfProfileNameThis object is used by the line alarm configuration
table in order to identify a row of this table.
When `dynamic' profiles are implemented, the profile
name is user specified. Also, the system will always
provide a default profile whose name is `DEFVAL'.
When `static' profiles are implemented, there is an
one-to-one relationship between each line and its
profile. In which case, the profile name will
need to algorithmicly represent the Line's ifIndex.
Therefore, the profile's name is a decimalized string
of the ifIndex that is fixed-length (i.e., 10) with
leading zero(s). For example, the profile name for
ifIndex which equals '15' will be '0000000015'. AdslLineProfileName -- Rsyntax OCTET STRING .1.3.6.1.2.1.10.94.1.1.15.1.1 |
adslAtucThresh15MinLofsThe number of Loss of Frame Seconds
encountered by an ADSL interface within any given 15
minutes performance data collection period, which
causes the SNMP agent to send an
adslAtucPerfLofsThreshTrap.
Limit of one trap will be sent for any one interval. A
value of `0' will disable the trap.rw INTEGER .1.3.6.1.2.1.10.94.1.1.15.1.2 |
adslAtucThresh15MinLossThe number of Loss of Signal Seconds
encountered by an ADSL interface within any given 15
minutes performance data collection period, which
causes the SNMP agent to send an
adslAtucPerfLossThreshTrap.
Limit of one trap will be sent for any one interval.
A value of `0' will disable the trap.rw INTEGER .1.3.6.1.2.1.10.94.1.1.15.1.3 |
adslAtucThresh15MinLolsThe number of Loss of Link Seconds
encountered by an ADSL interface within any given 15
minutes performance data collection period, which
causes the SNMP agent to send an
adslAtucPerfLolsThreshTrap. Limit of one trap will
be sent for any one interval. A value of `0' will
disable the trap.rw INTEGER .1.3.6.1.2.1.10.94.1.1.15.1.4 |
adslAtucThresh15MinLprsThe number of Loss of Power Seconds
encountered by an ADSL interface within any given 15
minutes performance data collection period, which
causes the SNMP agent to send an
adslAtucPerfLprsThreshTrap.
Limit of one trap will be sent for any one interval.
A value of `0' will disable the trap.rw INTEGER .1.3.6.1.2.1.10.94.1.1.15.1.5 |
adslAtucThresh15MinESsThe number of Errored Seconds
encountered by an ADSL interface within any given 15
minutes performance data collection period, which
causes the SNMP agent to send an
adslAtucPerfESsThreshTrap.
Limit of one trap will be sent for any one interval.
A value of `0' will disable the trap.rw INTEGER .1.3.6.1.2.1.10.94.1.1.15.1.6 |
adslAtucThreshFastRateUpApplies to `Fast' channels only.
Configured change in rate causing an
adslAtucRateChangeTrap. A trap is produced when:
ChanCurrTxRate >= ChanPrevTxRate plus the value of
this object. Set to `0' to disable.rw INTEGER -- Units -- bps .1.3.6.1.2.1.10.94.1.1.15.1.7 |
adslAtucThreshInterleaveRateUpApplies to `Interleave' channels only.
Configured change in rate causing an
adslAtucRateChangeTrap. A trap is produced when:
ChanCurrTxRate >= ChanPrevTxRate plus the value of
this object. Set to `0' to disable.rw INTEGER -- Units -- bps .1.3.6.1.2.1.10.94.1.1.15.1.8 |
adslAtucThreshFastRateDownApplies to `Fast' channels only.
Configured change in rate causing an
adslAtucRateChangeTrap. A trap is produced when:
ChanCurrTxRate <= ChanPrevTxRate minus the value of
this object. Set to `0' to disable.rw INTEGER -- Units -- bps .1.3.6.1.2.1.10.94.1.1.15.1.9 |
adslAtucThreshInterleaveRateDownApplies to `Interleave' channels only.
Configured change in rate causing an
adslAtucRateChangeTrap. A trap is produced when:
ChanCurrTxRate <= ChanPrevTxRate minus the value of
this object. Set to `0' to disable.rw INTEGER -- Units -- bps .1.3.6.1.2.1.10.94.1.1.15.1.10 |
adslAtucInitFailureTrapEnableEnables and disables the InitFailureTrap. This
object is defaulted disable(2).rw Enumeration .1.3.6.1.2.1.10.94.1.1.15.1.11 |
adslAturThresh15MinLofsThe number of Loss of Frame Seconds
encountered by an ADSL interface within any given 15
minutes performance data collection period, which
causes the SNMP agent to send an
adslAtucPerfLofsThreshTrap.
Limit of one trap will be sent for any one interval.
A value of `0' will disable the trap.rw INTEGER .1.3.6.1.2.1.10.94.1.1.15.1.12 |
adslAturThresh15MinLossThe number of Loss of Signal Seconds
encountered by an ADSL interface within any given 15
minutes performance data collection period, which
causes the SNMP agent to send an
adslAtucPerfLossThreshTrap.
Limit of one trap will be sent for any one interval.
A value of `0' will disable the trap.rw INTEGER .1.3.6.1.2.1.10.94.1.1.15.1.13 |
adslAturThresh15MinLprsThe number of Loss of Power Seconds
encountered by an ADSL interface within any given 15
minutes performance data collection period, which
causes the SNMP agent to send an
adslAtucPerfLprsThreshTrap.
Limit of one trap will be sent for any one interval.
A value of `0' will disable the trap.rw INTEGER .1.3.6.1.2.1.10.94.1.1.15.1.14 |
adslAturThresh15MinESsThe number of Errored Seconds
encountered by an ADSL interface within any given 15
minutes performance data collection period, which
causes the SNMP agent to send an
adslAtucPerfESsThreshTrap.
Limit of one trap will be sent for any one interval.
A value of `0' will disable the trap.rw INTEGER .1.3.6.1.2.1.10.94.1.1.15.1.15 |
adslAturThreshFastRateUpApplies to `Fast' channels only.
Configured change in rate causing an
adslAtucRateChangeTrap. A trap is produced when:
ChanCurrTxRate >= ChanPrevTxRate plus the value of
this object. Set to `0' to disable.rw INTEGER -- Units -- bps .1.3.6.1.2.1.10.94.1.1.15.1.16 |
adslAturThreshInterleaveRateUpApplies to `Interleave' channels only.
configured change in rate causing an
adslAtucRateChangeTrap. A trap is produced when:
ChanCurrTxRate >= ChanPrevTxRate plus the value of
this object. Set to `0' to disable.rw INTEGER -- Units -- bps .1.3.6.1.2.1.10.94.1.1.15.1.17 |
adslAturThreshFastRateDownApplies to `Fast' channels only.
Configured change in rate causing an
adslAtucRateChangeTrap. A trap is produced when:
ChanCurrTxRate <= ChanPrevTxRate minus the value of
this object. Set to `0' to disable.rw INTEGER -- Units -- bps .1.3.6.1.2.1.10.94.1.1.15.1.18 |
adslAturThreshInterleaveRateDownApplies to `Interleave' channels only.
Configured change in rate causing an
adslAtucRateChangeTrap. A trap is produced when:
ChanCurrTxRate <= ChanPrevTxRate minus the value of
this object. Set to `0' to disable.rw INTEGER -- Units -- bps .1.3.6.1.2.1.10.94.1.1.15.1.19 |
adslLineAlarmConfProfileRowStatusThis object is used to create a new row or modify or
delete an existing row in this table.
A profile activated by setting this object to
`active'. When `active' is set, the system
will validate the profile.
Before a profile can be deleted or taken out of
service, (by setting this object to `destroy' or
`outOfService') it must be first unreferenced
from all associated lines.
If the implementator of this MIB has chosen not
to implement `dynamic assignment' of profiles, this
object's MIN-ACCESS is read-only and its value
is always to be `active'.rw RowStatus -- Rsyntax INTEGER { -- active(1), -- notInService(2), -- notReady(3), -- createAndGo(4), -- createAndWait(5), -- destroy(6) -- } .1.3.6.1.2.1.10.94.1.1.15.1.20 |
adslLCSMib OBJECT IDENTIFIER .1.3.6.1.2.1.10.94.1.1.16 |
adslTraps OBJECT IDENTIFIER .1.3.6.1.2.1.10.94.1.2 |
adslAtucTraps OBJECT IDENTIFIER .1.3.6.1.2.1.10.94.1.2.1 |
adslAtucPerfLofsThreshTrapLoss of Framing 15-minute interval threshold reached. TRAP-TYPE .1.3.6.1.2.1.10.94.1.2.1.0.1 |
adslAtucPerfLossThreshTrapLoss of Signal 15-minute interval threshold reached. TRAP-TYPE .1.3.6.1.2.1.10.94.1.2.1.0.2 |
adslAtucPerfLprsThreshTrapLoss of Power 15-minute interval threshold reached. TRAP-TYPE .1.3.6.1.2.1.10.94.1.2.1.0.3 |
adslAtucPerfESsThreshTrapErrored Second 15-minute interval threshold reached. TRAP-TYPE .1.3.6.1.2.1.10.94.1.2.1.0.4 |
adslAtucRateChangeTrapThe ATUCs transmit rate has changed (RADSL mode only) TRAP-TYPE .1.3.6.1.2.1.10.94.1.2.1.0.5 |
adslAtucPerfLolsThreshTrapLoss of Link 15-minute interval threshold reached. TRAP-TYPE .1.3.6.1.2.1.10.94.1.2.1.0.6 |
adslAtucInitFailureTrapATUC initialization failed. See adslAtucCurrStatus
for potential reasons. TRAP-TYPE .1.3.6.1.2.1.10.94.1.2.1.0.7 |
adslAturTraps OBJECT IDENTIFIER .1.3.6.1.2.1.10.94.1.2.2 |
adslAturPerfLofsThreshTrapLoss of Framing 15-minute interval threshold reached. TRAP-TYPE .1.3.6.1.2.1.10.94.1.2.2.0.1 |
adslAturPerfLossThreshTrapLoss of Signal 15-minute interval threshold reached. TRAP-TYPE .1.3.6.1.2.1.10.94.1.2.2.0.2 |
adslAturPerfLprsThreshTrapLoss of Power 15-minute interval threshold reached. TRAP-TYPE .1.3.6.1.2.1.10.94.1.2.2.0.3 |
adslAturPerfESsThreshTrapErrored Second 15-minute interval threshold reached. TRAP-TYPE .1.3.6.1.2.1.10.94.1.2.2.0.4 |
adslAturRateChangeTrapThe ATURs transmit rate has changed (RADSL mode only) TRAP-TYPE .1.3.6.1.2.1.10.94.1.2.2.0.5 |
adslConformance OBJECT IDENTIFIER .1.3.6.1.2.1.10.94.1.3 |
adslGroups OBJECT IDENTIFIER .1.3.6.1.2.1.10.94.1.3.1 |
adslLineGroup OBJECT IDENTIFIER .1.3.6.1.2.1.10.94.1.3.1.1 |
adslPhysicalGroup OBJECT IDENTIFIER .1.3.6.1.2.1.10.94.1.3.1.2 |
adslChannelGroup OBJECT IDENTIFIER .1.3.6.1.2.1.10.94.1.3.1.3 |
adslAtucPhysPerfRawCounterGroup OBJECT IDENTIFIER .1.3.6.1.2.1.10.94.1.3.1.4 |
adslAtucPhysPerfIntervalGroup OBJECT IDENTIFIER .1.3.6.1.2.1.10.94.1.3.1.5 |
adslAturPhysPerfRawCounterGroup OBJECT IDENTIFIER .1.3.6.1.2.1.10.94.1.3.1.6 |
adslAturPhysPerfIntervalGroup OBJECT IDENTIFIER .1.3.6.1.2.1.10.94.1.3.1.7 |
adslAtucChanPerformanceGroup OBJECT IDENTIFIER .1.3.6.1.2.1.10.94.1.3.1.8 |
adslAturChanPerformanceGroup OBJECT IDENTIFIER .1.3.6.1.2.1.10.94.1.3.1.9 |
adslLineProfileGroup OBJECT IDENTIFIER .1.3.6.1.2.1.10.94.1.3.1.10 |
adslLineAlarmConfProfileGroup OBJECT IDENTIFIER .1.3.6.1.2.1.10.94.1.3.1.11 |
adslLineProfileControlGroup OBJECT IDENTIFIER .1.3.6.1.2.1.10.94.1.3.1.12 |
adslAturLineGroup OBJECT IDENTIFIER .1.3.6.1.2.1.10.94.1.3.1.14 |
adslAturPhysicalGroup OBJECT IDENTIFIER .1.3.6.1.2.1.10.94.1.3.1.15 |
adslAturChannelGroup OBJECT IDENTIFIER .1.3.6.1.2.1.10.94.1.3.1.16 |
adslAturAtucPhysPerfRawCounterGroup OBJECT IDENTIFIER .1.3.6.1.2.1.10.94.1.3.1.17 |
adslAturAtucPhysPerfIntervalGroup OBJECT IDENTIFIER .1.3.6.1.2.1.10.94.1.3.1.18 |
adslAturAturPhysPerfRawCounterGroup OBJECT IDENTIFIER .1.3.6.1.2.1.10.94.1.3.1.19 |
adslAturAturPhysPerfIntervalGroup OBJECT IDENTIFIER .1.3.6.1.2.1.10.94.1.3.1.20 |
adslAturAtucChanPerformanceGroup OBJECT IDENTIFIER .1.3.6.1.2.1.10.94.1.3.1.21 |
adslAturAturChanPerformanceGroup OBJECT IDENTIFIER .1.3.6.1.2.1.10.94.1.3.1.22 |
adslAturLineProfileGroup OBJECT IDENTIFIER .1.3.6.1.2.1.10.94.1.3.1.23 |
adslAturLineAlarmConfProfileGroup OBJECT IDENTIFIER .1.3.6.1.2.1.10.94.1.3.1.24 |
adslAturLineProfileControlGroup OBJECT IDENTIFIER .1.3.6.1.2.1.10.94.1.3.1.25 |
adslCompliances OBJECT IDENTIFIER .1.3.6.1.2.1.10.94.1.3.2 |
adslLineMibCompliance OBJECT IDENTIFIER .1.3.6.1.2.1.10.94.1.3.2.1 |
adslLineMibAturCompliance OBJECT IDENTIFIER .1.3.6.1.2.1.10.94.1.3.2.2 |