HMRING-MGMT-SNMP-MIB
The Hirschmann Private Ring Redundancy MIB definitions for Platform devices.
Main OID:
hmRingRedundancy.1.3.6.1.4.1.248.14.5
113
Objects
Active
Status
3
Dependencies
Imported Objects
Objects
113 total| Object Name |
|---|
hmRingRedundancyThe Hirschmann Private Ring Redundancy MIB definitions for Platform devices. MODULE-IDENTITY .1.3.6.1.4.1.248.14.5 |
hmRingRedundancyEventThe events of hmAgent. OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.5.0 |
hmRingRedReconfigThe Ring Redundancy mechanism has switched over NOTIFICATION-TYPE .1.3.6.1.4.1.248.14.5.0.1 |
hmRingCplReconfigThe Ring Coupling mechanism has switched over NOTIFICATION-TYPE .1.3.6.1.4.1.248.14.5.0.2 |
hmRingRedConfigChangedThe configuration of the Ring Redundancy has changed. NOTIFICATION-TYPE .1.3.6.1.4.1.248.14.5.0.3 |
hmMrpReconfigThe Media Redundancy Protocol mechanism has switched over.
This trap is only sent if hmMrpMRMCheckMediaRedundancy is enabled. NOTIFICATION-TYPE .1.3.6.1.4.1.248.14.5.0.4 |
hmRpcReconfigThe Ring Redundancy mechanism has switched over. NOTIFICATION-TYPE .1.3.6.1.4.1.248.14.5.0.5 |
hmSrmReconfigThe Ring Redundancy mechanism has switched over. NOTIFICATION-TYPE .1.3.6.1.4.1.248.14.5.0.6 |
hmRingRedTableThis table contains variables to define
an entry in the ring redundancy database. SEQUENCE OF HmRingRedEntry .1.3.6.1.4.1.248.14.5.1 |
hmRingRedEntryThe entry of the hmRingRedTable. HmRingRedEntry .1.3.6.1.4.1.248.14.5.1.1 |
hmRingRedPrimGroupIDUnique index to identify the slot number of
the primary link port. This value is never
greater than hmSysGroupCapacity. Note that
row creation is done only by writing to
hmRingRedModero Integer32 .1.3.6.1.4.1.248.14.5.1.1.1 |
hmRingRedPrimIfIndexInterface index of the primary link.
Note that row creation is only done by
writing to hmRingRedModero Integer32 .1.3.6.1.4.1.248.14.5.1.1.2 |
hmRingRedPrimIfOpStateoperational state of the primary interface.ro Enumeration .1.3.6.1.4.1.248.14.5.1.1.3 |
hmRingRedRedGroupIDUnique index to identify the slot number of
the redundant link port. This value is never
greater than hmSysGroupCapacity.rw Integer32 .1.3.6.1.4.1.248.14.5.1.1.4 |
hmRingRedRedIfIndexInterface index of the redundant link.rw Integer32 .1.3.6.1.4.1.248.14.5.1.1.5 |
hmRingRedRedIfOpStateoperational state of the redundant interface.ro Enumeration .1.3.6.1.4.1.248.14.5.1.1.6 |
hmRingRedOperStateoperational state of an entry.
If a new entry is created by setting hmRingRedMode to create(1),
the operState returns a value of underCreation(1).
rmActive(2) indicates that redundancy-manager is configured
and a ring failure has occured.
rmInactive(3) indicates that redundancy-manager is configured
and ring is ok.
The value rs(4) is returend when hmRingRedMode is set to rs(4).ro Enumeration .1.3.6.1.4.1.248.14.5.1.1.7 |
hmRingRedModeDesired mode of operation.
To create, modify or deactivate an entry the value create(1)
have to be set. delete(2) removes the entry. rm(3) and rs(4)
activate the redundancy.rw Enumeration .1.3.6.1.4.1.248.14.5.1.1.8 |
hmRingRedConfigOperStateOperational state of the ring configuration.
rmConfigError(2) indicates that the ring is not
connected with both ringports of the redundancy
manager, one of the ring cables is connected to
another port of the redundancy manager.
ringConfigError(3) is returned when somewhere in
the ring a ring connection fails.
anotherRM(4) indicates that another redundancy
manager was detected in the same ring. In this case
the redundant ring ports of these redundancy managers
are blocked until only one redundancy manager remains
in the ring.
Notice: rmConfigError(2) and ringConfigError(3)
can only be detected by the redundancy manager
if the redundancy manager is inactive.ro Enumeration .1.3.6.1.4.1.248.14.5.1.1.9 |
hmRingRedRecoveryDelayThe hmRingRedRecoveryDelay with its parameter set
defines the maximum recovery delay of ring recovery in the HIPER Ring.
delay500(1) specifies the parameter set for the maximum
recovery delay of 500ms in the HIPER Ring.
delay300(2) specifies the parameter set for the maximum
recovery delay of 300ms in the HIPER Ring.rw Enumeration .1.3.6.1.4.1.248.14.5.1.1.10 |
hmRingCouplingTableThis table contains variables to define
an entry in the ring coupling database. SEQUENCE OF HmRingCouplingEntry .1.3.6.1.4.1.248.14.5.2 |
hmRingCouplingEntryThe entry of the hmRingCouplingTable. HmRingCouplingEntry .1.3.6.1.4.1.248.14.5.2.1 |
hmRingCplInterconnGroupIDUnique index to identify the slot number of
the coupling link port. This value is never
greater than hmSysGroupCapacity.
Note that row creation is done only by
writing to hmRingCplRowStatus.rw Integer32 .1.3.6.1.4.1.248.14.5.2.1.1 |
hmRingCplInterconnIfIndexInterface index of the coupling link.
Note that only those ports can be chosen
which do not belong to another L2 redundancy
mechanism like ring redundancy or dual homing
and that row creation is only done by
writing to hmRingCplRowStatus.rw Integer32 .1.3.6.1.4.1.248.14.5.2.1.2 |
hmRingCplInterconnIfOpStateOperational state of the coupling interface.
active(2) indicates that the port is switching.
standby(3) indicates that the port is in standby mode.
On the slave active(2) indicates that a ring coupling
failure has occured and the port is switching.
On the slave standby(3) indicates that the ring coupling is ok
and the slave is in standby mode.ro Enumeration .1.3.6.1.4.1.248.14.5.2.1.3 |
hmRingCplControlGroupIDUnique index to identify the slot number of
the control link port in case of outband-control.
This value is never greater than hmSysGroupCapacity.rw Integer32 .1.3.6.1.4.1.248.14.5.2.1.4 |
hmRingCplControlIfIndexInterface index of the control link in case
of outband-control.
Note that only those ports can be chosen
which do not belong to another L2 redundancy
mechanism like ring redundancy or dual homing
and that row creation is only done by
writing to hmRingCplRowStatus.rw Integer32 .1.3.6.1.4.1.248.14.5.2.1.5 |
hmRingCplControlIfOpStateOperational state of the control interface in case
of outband-control.ro Enumeration .1.3.6.1.4.1.248.14.5.2.1.6 |
hmRingCplControlModeControl mode of the ring coupling which can only be
chosen by the slave, the master just reports his current
control mode. unknown(3) cannot be set.
In outband(1) mode an additional line must connect the control
interfaces between the two partners in the ring coupling.
In inband(2) mode only the coupling link port is needed.
In local(4) mode the coupling link port and the partner port are
located on the same switch.
disable(5) deactivates the ring coupling functionality.rw Enumeration .1.3.6.1.4.1.248.14.5.2.1.7 |
hmRingCplPartnerIpAddrIP Address of the partner in the ring coupling.ro IpAddress .1.3.6.1.4.1.248.14.5.2.1.8 |
hmRingCplPartnerInterconnGroupIDIndex identifies the slot number of the
coupling link port of the partner in the
ring coupling.
This variable can only be set if the
hmRingCplControlMode is local(4).rw Integer32 .1.3.6.1.4.1.248.14.5.2.1.9 |
hmRingCplPartnerInterconnIfIndexInterface index identifies the coupling link of the
partner in the ring coupling.
This variable can only be set if the
hmRingCplControlMode is local(4).rw Integer32 .1.3.6.1.4.1.248.14.5.2.1.10 |
hmRingCplPartnerInterconnIfOpStateOperational state of the coupling interface of the
partner in the ring coupling.
active(2) indicates that the partner port is switching.
standby(3) indicates that the partner port is in standby mode.ro Enumeration .1.3.6.1.4.1.248.14.5.2.1.11 |
hmRingCplOperStateOperational state of an entry.
If a new entry is created by setting hmRingCplRowStatus to create(1),
the operState returns a value of underCreation(1).
slave(2) indicates that switch is configured to be the slave of the
ring coupling, that means the switch is in standby mode.
master(3) indicates that a switch is configured to be
the master of the ring coupling.
local(4) indicates that the switch is configured to control a ring
coupling where the coupling port and the partner port are located
on the same switch.
disable(5) indicates that the ring coupling functionality is switched off.ro Enumeration .1.3.6.1.4.1.248.14.5.2.1.12 |
hmRingCplModeDesired mode of operation.
slaveOn(2) activates the slave.
slaveOff(1) deactivates the slave, the ring coupling is disabled and
the switch acts from now in normal rs mode.
Note that this mode can only be set if the slave is not
activated or deactivated by a DIP-switch.
disable(3) indicates that the ring coupling functionality is switched off.rw Enumeration .1.3.6.1.4.1.248.14.5.2.1.13 |
hmRingCplRowStatusDefines the status of a ring coupling database entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.248.14.5.2.1.14 |
hmRingCplConfigOperStateOperational state of the ring coupling configuration.
slaveCouplingLinkError(2) indicates that the coupling link
is not connected with the coupling port of the slave but with
another port of the slave.
In case of outband control additional failures can be
detected:
slaveControlLinkError(3) indicates that the control
port of the slave has either no link or the link
fails.
masterControlLinkError(4) indicates that the control
link is not connected with the control port of the
master but with another port of the master.
twoSlaves(5) is returned when two slaves are connected
by the control line.
localPartnerLinkError(6) indicates that the partner coupling link
is not connected with the partner port of the slave but with
another port of the slave in local control mode.
localInvalidCouplingPort(7) indicates that in local mode the coupling
line is connected to another switch and not on the same switch like
the partner line.
couplingPortNotAvailable(8), controlPortNotAvailable(9) and
partnerPortNotAvailable(10) indicate that this port is not available
because the module related to this port is not available or the port
does not exist on this module.ro Enumeration .1.3.6.1.4.1.248.14.5.2.1.15 |
hmRingCplCouplingLinksMaximum coupling links between two coupled rings in case of a failure
in one of the coupled rings.
If there is no connection starting from the switch in slave or local
operational state over the route of the coupled rings or nets to oneself
the slave or the local mode want to set the coupling port in forwarding
after a timeout period.
basicRedundancy(1) prevents the slave or the local mode from setting its
coupling port into forwarding in case of the described failure. In this
case the segment which is connected to this coupling port is unreachable
until the failure is eliminated.
In extendedRedundancy(2) the coupling port and the partner coupling port
are allowed to be in forwarding.rw Enumeration .1.3.6.1.4.1.248.14.5.2.1.16 |
hmRingCplExtendedDiagAdditional operational states detected by the slave or in local mode.
basicRedundancyInactive(2) indicates that the coupling port has been
prevented from setting into forwarding (please see description
of hmRingCplCouplingLinks).ro Enumeration .1.3.6.1.4.1.248.14.5.2.1.17 |
hmRingCplNetCouplingSpecifies the kind of the coupled net segment.
If two HIPER Rings are coupled ringCoupling(1) must be used.
In netCoupling(2) the coupled segment is no HIPER Ring topology and the
switches in the coupled net segment may be connected with other ports than
their ringports.
Notice: if the ring coupling mechanism switches over, in ringCoupling(1)
only the address tables of the switches in the two coupled HIPER Rings will be
erased, in netCoupling(2) the address tables of all switches in the
coupled net will be erased.rw Enumeration .1.3.6.1.4.1.248.14.5.2.1.18 |
hmRingCplConfigSourceReturns the Source by which the feature is controlled.ro Enumeration .1.3.6.1.4.1.248.14.5.2.1.19 |
hmMrpTableEvery entry in this table contains information about
a Media Redundancy Protocol (MRP) domain. SEQUENCE OF HmMrpEntry .1.3.6.1.4.1.248.14.5.3 |
hmMrpEntryAn entry in the hmMrpTable. HmMrpEntry .1.3.6.1.4.1.248.14.5.3.1 |
hmMrpDomainIDUniversally unique identifier belongs to the MRP domain
which represents a ring. OCTET STRING .1.3.6.1.4.1.248.14.5.3.1.1 |
hmMrpRingport1GroupIDUnique index to identify the slot number of the ringport 1 in the
MRP domain.
This value is never greater than hmSysGroupCapacity.rw Integer32 .1.3.6.1.4.1.248.14.5.3.1.2 |
hmMrpRingport1IfIndexInterface index of the ringport 1 in the MRP domain.rw Integer32 .1.3.6.1.4.1.248.14.5.3.1.3 |
hmMrpRingport1OperStateOperational state of ringport 1.
disabled(1) indicates that all frames are dropped.
blocked(2) indicates that all frame are dropped except
- MRP topology change frames and MRP test frames from a MRM,
- MRP link change frames from a MRC,
- frames from other protocols that also define to pass
blocked(2) ports.
forwarding(3) indicates that all frames are passed through
according to the forwarding behavior of IEEE 802.1D.
not-connected(4) indicates that the port has no link.ro Enumeration .1.3.6.1.4.1.248.14.5.3.1.4 |
hmMrpRingport2GroupIDUnique index to identify the slot number of the ringport 2 in the
MRP domain.
This value is never greater than hmSysGroupCapacity.rw Integer32 .1.3.6.1.4.1.248.14.5.3.1.5 |
hmMrpRingport2IfIndexInterface index of the ringport 2 in the MRP domain.rw Integer32 .1.3.6.1.4.1.248.14.5.3.1.6 |
hmMrpRingport2OperStateOperational state of ringport 2.
disabled(1) indicates that all frames are dropped.
blocked(2) indicates that all frame are dropped except
- MRP topology change frames and MRP test frames from a MRM,
- MRP link change frames from a MRC,
- frames from other protocols that also define to pass
blocked(2) ports.
forwarding(3) indicates that all frames are passed through
according to the forwarding behavior of IEEE 802.1D.
not-connected(4) indicates that the port has no link.ro Enumeration .1.3.6.1.4.1.248.14.5.3.1.7 |
hmMrpVlanIDVLAN identifier of the MRP domain.rw Integer32 .1.3.6.1.4.1.248.14.5.3.1.8 |
hmMrpExpectedRoleControl the role of the MRP entity in the MRP domain.
If the value is set to client(1) the entity will be in the
role of a Media Redundancy Client (MRC).
If the value is set to manager(2) the entity will be in the
role of a Media Redundancy Manager (MRM).rw Enumeration .1.3.6.1.4.1.248.14.5.3.1.9 |
hmMrpMRCLinkDownIntervalInterval for sending link down MRP link change frames on ringports.ro Integer32 .1.3.6.1.4.1.248.14.5.3.1.10 |
hmMrpMRCLinkUpIntervalInterval for sending link up MRP link change frames on ringports.ro Integer32 .1.3.6.1.4.1.248.14.5.3.1.11 |
hmMrpMRCLinkChangeCountMRP link change frame count which controls repeated transmission of
MRP link change frames.ro Integer32 .1.3.6.1.4.1.248.14.5.3.1.12 |
hmMrpMRCBlockedSupportedAbility of the MRC to receive and forward MRP test frames, MRP link
change frames and MRP topology change frames at a ringport whose
port state is blocked.
enabled(1) indicates that the MRC is able to receive and forward
these MRP frames at a ringport whose port state is blocked.
disabled(2) indicates that the MRC is not able to receive and forward
these MRP frames at a ringport whose port state is blocked.ro Enumeration .1.3.6.1.4.1.248.14.5.3.1.13 |
hmMrpMRMPriorityPriority of the MRM. A lower value indicates a higher priority.rw Integer32 .1.3.6.1.4.1.248.14.5.3.1.14 |
hmMrpMRMTopologyChangeIntervalInterval for sending MRP topology change frames on ringports.ro Integer32 .1.3.6.1.4.1.248.14.5.3.1.15 |
hmMrpMRMTopologyChangeRepeatCountInterval count which controls repeated transmission of MRP
topology change frames.ro Integer32 .1.3.6.1.4.1.248.14.5.3.1.16 |
hmMrpMRMShortTestIntervalShort interval for sending MRP test frames on ringports after
link changes in the ring.ro Integer32 .1.3.6.1.4.1.248.14.5.3.1.17 |
hmMrpMRMDefaultTestIntervalDefault interval for sending MRP test frames on ringports.ro Integer32 .1.3.6.1.4.1.248.14.5.3.1.18 |
hmMrpMRMTestMonitoringCountInterval count for monitoring the reception of MRP test frames.ro Integer32 .1.3.6.1.4.1.248.14.5.3.1.19 |
hmMrpMRMNonBlockingMRCSupportedAbility of the MRM to support MRC in the ring which have
hmMrpMRCBlockedSupported set disabled.
enabled(1) indicates that the MRM is able to support MRC in the ring
which have hmMrpMRCBlockedSupported set disabled.
disabled(2) indicates that the MRM is not able to support MRC in the
ring which have hmMrpMRCBlockedSupported set disabled.ro Enumeration .1.3.6.1.4.1.248.14.5.3.1.20 |
hmMrpMRMTestMonitoringExtendedCountExtended interval count for monitoring the reception of MRP test
frames.
This value is used by the MRP if hmMrpMRMNonBlockingMRCSupported is
is set enabled.ro Integer32 .1.3.6.1.4.1.248.14.5.3.1.21 |
hmMrpMRMReactOnLinkChangeSpecifies whether the MRM reacts on all MRP link change frames or not.
enabled(1) indicates that the MRM reacts on all MRP link change frames.
disabled(2) indicates that the MRM does not react on link down MRP link change
frames.rw Enumeration .1.3.6.1.4.1.248.14.5.3.1.22 |
hmMrpMRMCheckMediaRedundancySpecifies whether monitoring of MRM state is enabled or disabled
in the redundancy domain.
enabled(1) indicates that the MRM monitors its state.
disabled(2) indicates that the MRM does not monitor its state.ro Enumeration .1.3.6.1.4.1.248.14.5.3.1.23 |
hmMrpMRMRealRoleStateOperational role of the MRP entity in the MRP domain.
client(1) indicates that the MRP entity is in a MRC role.
manager(2) indicates that the MRP entity is the manager MRM
of this MRP domain.
undefined(3) indicates that the MRP entity doesn't work.
This value can only be read if hmMrpMRMCheckMediaRedundancy is set
enabled.ro Enumeration .1.3.6.1.4.1.248.14.5.3.1.24 |
hmMrpMRMRealRingStateActual ring state of the redundancy domain.
open(1) indicates that the ring is opened.
closed(2) indicates that the ring is closed.
undefined(3) indicates an undefined ring state or can be read if
hmMrpMRMRealRoleState contains the value client.
This value can only be read if hmMrpMRMCheckMediaRedundancy is set
enabled.ro Enumeration .1.3.6.1.4.1.248.14.5.3.1.25 |
hmMrpRowStatusDefines the status of the MRP database entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.248.14.5.3.1.26 |
hmMrpRedOperStateOperational state of ring redundancy in the MRP domain.
redGuaranteed(1) indicates that ring redundancy is guaranteed in the
MRP domain.
redNotGuaranteed(2) indicates that ring redundancy is not guaranteed
in the MRP domain.ro Enumeration .1.3.6.1.4.1.248.14.5.3.1.27 |
hmMrpConfigOperStateOperational state of the configuration in the MRP domain.
noError(1) indicates that no configuration error was detected.
ringportLinkError(2) indicates that one of the ring lines is not
connected with one of the ring ports in the MRP domain.ro Enumeration .1.3.6.1.4.1.248.14.5.3.1.28 |
hmMrpDomainNameA logical name for the MRP domain to ease the management of MRP
domains.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.248.14.5.3.1.29 |
hmMrpMRMRecoveryDelayThe MRM defines with its parameter set the maximum recovery
delay of ring recovery in the MRP domain.
delay500(1) specifies the parameter set for the maximum
recovery delay of 500ms in the MRP domain.
delay200(2) specifies the parameter set for the maximum
recovery delay of 200ms in the MRP domain.rw Enumeration .1.3.6.1.4.1.248.14.5.3.1.30 |
hmRpcTableEvery entry in this table contains information about
a Ring Protocol Control (RPC) domain. SEQUENCE OF HmRpcEntry .1.3.6.1.4.1.248.14.5.4 |
hmRpcEntryAn entry in the hmRpcTable. HmRpcEntry .1.3.6.1.4.1.248.14.5.4.1 |
hmRpcRingProtocolDesired version of the ring protocol in the RPC domain.
If the value is set to FastHiperRing(3) the entity will
run the Fast Hiper Ring protocol.
Note: Not all entities may support all ring protocols.
If an entity does not support the desired protocol
a row in this table cannot be created for this
protocol.rw Enumeration .1.3.6.1.4.1.248.14.5.4.1.1 |
hmRpcRingIDIdentifier of the ring in the RPC domain.rw Integer32 .1.3.6.1.4.1.248.14.5.4.1.2 |
hmRpcRingNameName of the ring in RPC domain.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.248.14.5.4.1.3 |
hmRpcRingport1GroupIDUnique index to identify the slot number of ringport 1
in the RPC domain.
This value is never greater than hmSysGroupCapacity.rw Integer32 .1.3.6.1.4.1.248.14.5.4.1.4 |
hmRpcRingport1IfIndexInterface index of ringport 1 in the RPC domain.rw Integer32 .1.3.6.1.4.1.248.14.5.4.1.5 |
hmRpcRingport1OperStateOperational state of ringport 1.
disabled(1) indicates that all frames are dropped.
blocked(2) indicates that all frames are dropped except
- frames used by the selected ring protocol selected
which are defined to pass blocked(2) ports,
- frames from other protocols which are defined
to pass blocked(2) ports.
forwarding(3) indicates that all frames are passed through
according to the forwarding behavior of IEEE 802.1D.
not-connected(4) indicates that the port has no link.ro Enumeration .1.3.6.1.4.1.248.14.5.4.1.6 |
hmRpcRingport2GroupIDUnique index to identify the slot number of ringport 2
in the RPC domain.
This value is never greater than hmSysGroupCapacity.rw Integer32 .1.3.6.1.4.1.248.14.5.4.1.7 |
hmRpcRingport2IfIndexInterface index of ringport 2 in the RPC domain.rw Integer32 .1.3.6.1.4.1.248.14.5.4.1.8 |
hmRpcRingport2OperStateOperational state of ringport 2.
disabled(1) indicates that all frames are dropped.
blocked(2) indicates that all frames are dropped except
- frames used by the selected ring protocol selected
which are defined to pass blocked(2) ports,
- frames from other protocols which are defined
to pass blocked(2) ports.
forwarding(3) indicates that all frames are passed through
according to the forwarding behavior of IEEE 802.1D.
not-connected(4) indicates that the port has no link.ro Enumeration .1.3.6.1.4.1.248.14.5.4.1.9 |
hmRpcVlanIDVLAN identifier of the RPC domain.
If value is set to 0 no VLAN is assigned.rw Integer32 .1.3.6.1.4.1.248.14.5.4.1.10 |
hmRpcAdminStateAdmin state of the entity in the RPC domain.
If the value is set to client(1) the entity will be in the
role of a redundancy client.
If the value is set to manager(2) the entity will be in the
role of a redundancy manager.rw Enumeration .1.3.6.1.4.1.248.14.5.4.1.11 |
hmRpcOperStateOperational state of the entity in the RPC domain.
client(1) indicates that the entity is in the role of a
redundancy client.
manager(2) indicates that the entity is in the role of a
redundancy manager.
disabled(3) indicates that the protocol does not work
on the entity.ro Enumeration .1.3.6.1.4.1.248.14.5.4.1.12 |
hmRpcRingOperStateOperational state of the ring in the RPC domain.
undefined(1) indicates either an undefined ring state or the entity
may have the role of a redundancy client.
open(1) indicates that the ring is opened.
closed(2) indicates that the ring is closed.ro Enumeration .1.3.6.1.4.1.248.14.5.4.1.13 |
hmRpcRedundancyOperStateOperational state of the ring redundancy in the RPC domain.
redGuaranteed(1) indicates that ring redundancy is guaranteed in
the RPC domain.
redNotGuaranteed(2) indicates that ring redundancy is not
guaranteed in the RPC domain.ro Enumeration .1.3.6.1.4.1.248.14.5.4.1.14 |
hmRpcConfigOperStateOperational state of the configuration in the RPC domain.
noError(1) indicates that no configuration error was detected.
ringportLinkError(2) indicates that the ring port has no link
or one of the ring lines is not connected with one of the ring
ports of the entity but to another port of the entity (this
may be available only if the entity has the role of a redundancy
manager).
singleSideReceive(3) indicates that the redundancy manager
receives test frames only on one ringport (only available if
the entity has the role of a redundancy manager).
multipleRM(4) indicates that the redundancy manager receives
frames from another redundancy manager (only available if the
entity has the role of a redundancy manager).ro Enumeration .1.3.6.1.4.1.248.14.5.4.1.15 |
hmRpcRowStatusDefines the status of the RPC database entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.248.14.5.4.1.16 |
hmRpcNodesManager only: number of nodes in the RPC ring.rw Integer32 .1.3.6.1.4.1.248.14.5.4.1.17 |
hmRpcRoundTripDelayManager only: maximum Round-Trip-Delay (in microseconds)
which was measured since the RowStatus of the RPC
domain has been set active.ro Unsigned32 .1.3.6.1.4.1.248.14.5.4.1.18 |
hmMultiHiperRing OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.5.5 |
hmSrmMaxInstancesMaximum number of supported SRM instances in the hmSrmTable.ro Integer32 .1.3.6.1.4.1.248.14.5.5.1 |
hmSrmTableEvery entry in this table contains information about
a Sub-Ring Manager (SRM) domain in the Multi HIPER Ring. SEQUENCE OF HmSrmEntry .1.3.6.1.4.1.248.14.5.5.5 |
hmSrmEntryAn entry in the hmSrmTable. HmSrmEntry .1.3.6.1.4.1.248.14.5.5.5.1 |
hmSrmRingIDIdentifier of the sub-ring in the SRM domain.rw Integer32 .1.3.6.1.4.1.248.14.5.5.5.1.1 |
hmSrmRingProtocolIf the value is set to standardMRP(4) the entity will run
the MRP protocol.
Note: If using standardMRP(4) all clients in the sub-ring
segment must run MRP according to IEC 62439.rw Enumeration .1.3.6.1.4.1.248.14.5.5.5.1.2 |
hmSrmRingNameName of the sub-ring in SRM domain.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.248.14.5.5.5.1.3 |
hmSrmRingport1GroupIDUnique index to identify the slot number of ringport 1
in the SRM domain.
This value is never greater than hmSysGroupCapacity.rw Integer32 .1.3.6.1.4.1.248.14.5.5.5.1.4 |
hmSrmRingport1IfIndexInterface index of ringport 1 in the SRM domain.rw Integer32 .1.3.6.1.4.1.248.14.5.5.5.1.5 |
hmSrmRingport1OperStateOperational state of ringport 1.
disabled(1) indicates that all frames are dropped.
blocked(2) indicates that all frames are dropped except
- frames used by the selected ring protocol
which are defined to pass blocked(2) ports,
- frames from other protocols which are defined
to pass blocked(2) ports.
forwarding(3) indicates that all frames are passed through
according to the forwarding behavior of IEEE 802.1D.
not-connected(4) indicates that the port has no link.ro Enumeration .1.3.6.1.4.1.248.14.5.5.5.1.6 |
hmSrmVlanIDVLAN identifier of the SRM domain.
If value is set to 0 no VLAN is assigned.rw Integer32 .1.3.6.1.4.1.248.14.5.5.5.1.7 |
hmSrmAdminStateAdmin state of the entity in the SRM domain.
If the value is set to manager(1) the entity will be in the
role of a Sub-Ring Manager in the Multi HIPER Ring.
If the value is set to redundantManager(2) the entity will be
in the role of the Sub-Ring Manager in the Multi HIPER Ring which
will block its ringport if the sub-ring is closed.
If the value is set to singleManager(3) the entity will be
in the role of the single-manager in the Multi HIPER Ring which
has both ends of a sub-ring connected and will block one of these ends
if the sub-ring is closed.
Note: Two instances in the hmSrmTable are needed to build a single-manager
where both instances must have singleManager(3) selected.
Note: The sub-ring in the Multi HIPER Ring has two managers at the same time.
The redundant manager can be designated.rw Enumeration .1.3.6.1.4.1.248.14.5.5.5.1.8 |
hmSrmOperStateOperational state of the entity in the SRM domain.
manager(1) indicates that the entity is in the role of a
Sub-Ring Manager in the Multi HIPER Ring.
redundantManager(3) indicates that the entity is in the
role of the Sub-Ring Manager in the Multi HIPER Ring which
will block its ringport if the sub-ring is closed.
singleManager(3) indicates that the entity is in the
role of the single manager.
disabled(4) indicates that the protocol does not work on the entity.ro Enumeration .1.3.6.1.4.1.248.14.5.5.5.1.9 |
hmSrmRingOperStateOperational state of the sub-ring in the SRM domain.
undefined(1) indicates an undefined sub-ring state.
open(2) indicates that the sub-ring is opened.
closed(3) indicates that the sub-ring is closed.ro Enumeration .1.3.6.1.4.1.248.14.5.5.5.1.10 |
hmSrmRedundancyOperStateOperational state of the ring redundancy in the SRM domain.
redGuaranteed(1) indicates that ring redundancy is guaranteed in
the SRM domain.
redNotGuaranteed(2) indicates that ring redundancy is not
guaranteed in the SRM domain.ro Enumeration .1.3.6.1.4.1.248.14.5.5.5.1.11 |
hmSrmConfigOperStateOperational state of the configuration in the SRM domain.
noError(1) indicates that no configuration error was detected.
ringportLinkError(2) indicates that the ring port has no link
or one of the sub-ring lines is not connected with one of the ring
ports of the entity but to another port of the entity.
multipleSRM(3) indicates that the Sub-Ring Manager receives frames
from more than one Sub-Ring Managers in the sub-ring.
noPartnerManager(4) indicates that the Sub-Ring Manager receives
his own frames.
concurrentVLAN(5) indicates that the VLAN of the SRM domain is
used by MRP in the basis ring.
concurrentPort(6) indicates that the ringport of the SRM domain
is used by another redundancy protocol.
concurrentRedundancy(7) indicates the SRM domain is not active
because of another active redundancy protocol.
trunkMember(8) indicates that the ringport of the SRM domain
is member of a trunk.
sharedVLAN(9) indicates the SRM domain cannot be active
because Shared VLAN is active and MRP is used in the
basis ring too.ro Enumeration .1.3.6.1.4.1.248.14.5.5.5.1.12 |
hmSrmRowStatusDefines the status of the SRM database entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.248.14.5.5.5.1.13 |
hmSrmNodesNumber of nodes in the sub-ring.
Note: Will get neccessary if the SRM runs on a fpga.rw Integer32 .1.3.6.1.4.1.248.14.5.5.5.1.14 |
hmSrmMRPDomainIDOnly for MRP:
Universally unique identifier belongs to the MRP domain
which represents a sub-ring.rw OCTET STRING .1.3.6.1.4.1.248.14.5.5.5.1.15 |
hmSrmPartnerMACThe MAC address of the partner Sub-Ring Manager in the
same sub-ring domain.ro OCTET STRING .1.3.6.1.4.1.248.14.5.5.5.1.16 |