HMIOMODULE-SNMP-MIB
The Hirschmann Private IO Module definitions for Platform devices.
Main OID:
hmIOModuleGroup.1.3.6.1.4.1.248.14.1.13
37
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
37 total| Object Name |
|---|
hmIOModDigInputChangeTrapThis trap is sent if the state of an input changes.
This trap is sent only when hmIOModConfigDigInputSnmpTrap is set
to enabled (1). NOTIFICATION-TYPE .1.3.6.1.4.1.248.14.1.0.16 |
hmIOModDigOutputChangeTrapThis trap is sent if the state of an input changes.
This trap is sent when hmIOModConfigDigOutputSnmpTrap is set
to enabled (1) or when the output value changes from or to invalid (3) NOTIFICATION-TYPE .1.3.6.1.4.1.248.14.1.0.17 |
hmIOModuleGroupThe Hirschmann Private IO Module definitions for Platform devices. MODULE-IDENTITY .1.3.6.1.4.1.248.14.1.13 |
hmIOModuleConfigGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.1.13.1 |
hmIOModConfigCommon OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.1.13.1.1 |
hmIOModConfigDigInputAdminStateenables sending SNMP traps or log events on input change.
(if disable(2) input task will do nothing).rw HmEnabledStatus .1.3.6.1.4.1.248.14.1.13.1.1.1 |
hmIOModConfigDigOutputAdminStateenables polling of output values (if disable(2) output task will do nothing).rw HmEnabledStatus .1.3.6.1.4.1.248.14.1.13.1.1.2 |
hmIOModConfigDigInputRefreshIntervalThe refresh interval (in ms) of the input values.
Minimum 500ms, Maximum 10000ms (10s).rw Integer32 .1.3.6.1.4.1.248.14.1.13.1.1.3 |
hmIOModConfigDigOutputRefreshIntervalThe refresh interval (in ms) of the output values.
Minimum 500ms, Maximum 10000ms (10s).rw Integer32 .1.3.6.1.4.1.248.14.1.13.1.1.4 |
hmIOModConfigDigOutputRetryCountThe retry count for the output values.
when after the number of configured retries no SNMP get request
was answered, the output value (hmIOModOutputValue) will be
set to invalid (3). Minimum 1, Maximum 10.rw Integer32 .1.3.6.1.4.1.248.14.1.13.1.1.5 |
hmIOModConfigDigInputTableIO module config table for inputs SEQUENCE OF HmIOModConfigDigInputEntry .1.3.6.1.4.1.248.14.1.13.1.2 |
hmIOModConfigDigInputEntryIO module config entry for inputs HmIOModConfigDigInputEntry .1.3.6.1.4.1.248.14.1.13.1.2.1 |
hmIOModConfigDigInputModIDThe module ID of an input. Integer32 .1.3.6.1.4.1.248.14.1.13.1.2.1.1 |
hmIOModConfigDigInputIDThe ID of an input. Integer32 .1.3.6.1.4.1.248.14.1.13.1.2.1.2 |
hmIOModConfigDigInputLogEventTrigger an event log when input status changes.
If the value is disable (2), no event log entry will be written.
If the value is enable (1), an event log entry will be written when
the input state changes.
The input state will be checked acording to the refresh interval
entered in hmIOModConfigDigInputRefreshInterval.rw HmEnabledStatus .1.3.6.1.4.1.248.14.1.13.1.2.1.3 |
hmIOModConfigDigInputSnmpTrapTrigger an SNMP trap log when input status changes.
If the value is disable (2), no SNMP trap will be sent.
If the value is enable (1), a SNMP trap will be sent when
the input state changes.
The SNMP trap will be sent to all receivers configured
in hmAgentSnmpTrapReceiverConfigTable.
The input state will be checked acording to the refresh interval entered
in hmIOModConfigDigInputRefreshInterval.rw HmEnabledStatus .1.3.6.1.4.1.248.14.1.13.1.2.1.4 |
hmIOModConfigDigOutputTableIO module config table for outputs SEQUENCE OF HmIOModConfigDigOutputEntry .1.3.6.1.4.1.248.14.1.13.1.3 |
hmIOModConfigDigOutputEntryIO module config entry for outputs HmIOModConfigDigOutputEntry .1.3.6.1.4.1.248.14.1.13.1.3.1 |
hmIOModConfigDigOutputModIDThe module ID of an output. Integer32 .1.3.6.1.4.1.248.14.1.13.1.3.1.1 |
hmIOModConfigDigOutputIDThe ID of an output. Integer32 .1.3.6.1.4.1.248.14.1.13.1.3.1.2 |
hmIOModConfigDigOutputLogEventTrigger an event log when output status changes.
If the value is disable (2), no event log entry will be written.
If the value is enable (1), an event log entry will be written when
the output state changes.
The output state will be checked acording to the refresh interval
entered in hmIOModConfigDigOutputRefreshInterval.rw HmEnabledStatus .1.3.6.1.4.1.248.14.1.13.1.3.1.3 |
hmIOModConfigDigOutputSnmpTrapTrigger an SNMP trap log when output status changes.
If the value is disable (2), no SNMP trap will be sent.
If the value is enable (1), a SNMP trap will be sent when
the output state changes.
The SNMP trap will be sent to all receivers configured
in hmAgentSnmpTrapReceiverConfigTable.
The output state will be checked acording to the refresh interval
entered in hmIOModConfigDigOutputRefreshInterval.rw HmEnabledStatus .1.3.6.1.4.1.248.14.1.13.1.3.1.4 |
hmIOModConfigDigOutputSourceIPThe IP address of an input mirrored to the output.
Use 0.0.0.0 if the output should not be set.
In this case hmIOModOutputValue is invalid (3).
Use 127.0.0.1 if an local input should be used.rw IpAddress .1.3.6.1.4.1.248.14.1.13.1.3.1.5 |
hmIOModConfigDigOutputSourceModIDThe module ID of an input mirrored to the output.
Ignored when hmIOModConfigDigOutputSourceIP is 0.0.0.0.rw Integer32 .1.3.6.1.4.1.248.14.1.13.1.3.1.6 |
hmIOModConfigDigOutputSourceIDThe ID of an input mirrored to the output.
Ignored when hmIOModConfigDigOutputSourceIP is 0.0.0.0.rw Integer32 .1.3.6.1.4.1.248.14.1.13.1.3.1.7 |
hmIOModConfigDigOutputSourcePortThe SNMP port number being used by the input mirrored to the output.
This port would be the destination for the SNMP requests for
polling the state of the input.rw InetPortNumber (INET-ADDRESS-MIB) .1.3.6.1.4.1.248.14.1.13.1.3.1.8 |
hmIOModuleValueGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.14.1.13.2 |
hmIOModValueDigInputTableIO module value table for inputs SEQUENCE OF HmIOModValueDigInputEntry .1.3.6.1.4.1.248.14.1.13.2.1 |
hmIOModValueDigInputEntryIO module value entry for inputs HmIOModValueDigInputEntry .1.3.6.1.4.1.248.14.1.13.2.1.1 |
hmIOModValueDigInputModIDThe module ID of an input. Integer32 .1.3.6.1.4.1.248.14.1.13.2.1.1.1 |
hmIOModValueDigInputIDThe ID of an input. Integer32 .1.3.6.1.4.1.248.14.1.13.2.1.1.2 |
hmIOModValueDigInputValueStatus of the input.
If the value is not-available(0), then the IO module is not plugged in,
if the value is high(1), the input has high (+24V) value,
if the value is low(2), the input has low (0V) value.ro Enumeration .1.3.6.1.4.1.248.14.1.13.2.1.1.3 |
hmIOModValueDigOutputTableIO module value table for outputs SEQUENCE OF HmIOModValueDigOutputEntry .1.3.6.1.4.1.248.14.1.13.2.2 |
hmIOModValueDigOutputEntryIO module value entry for outputs HmIOModValueDigOutputEntry .1.3.6.1.4.1.248.14.1.13.2.2.1 |
hmIOModValueDigOutputModIDThe module ID of an Output. Integer32 .1.3.6.1.4.1.248.14.1.13.2.2.1.1 |
hmIOModValueDigOutputIDThe ID of an Output. Integer32 .1.3.6.1.4.1.248.14.1.13.2.2.1.2 |
hmIOModValueDigOutputValueStatus of the output.
If the value is not-available(0), then the IO module is not plugged in,
if the value is high(1), the output has high (+24V) value,
if the value is low(2), the output has low (0V) value.
If the value is invalid (3), the output has low (0V) value and
the IO input source is configured but can not be read.
If the value is not-configured (4), the output has low (0V) value and
has no IO input source configured.ro Enumeration .1.3.6.1.4.1.248.14.1.13.2.2.1.3 |