HM2-WWAN-MIB
AI MIB Summary
The HM2-WWAN-MIB module enables SNMP-based monitoring and management of Hirschmann (Belden) industrial switches and routers equipped with Wide Area Network (WWAN) cellular interfaces, specifically exposing metrics for cellular modem status, signal strength, network registration states, and data session counters.
This MIB defines the SNMP interface for Hirschmann WWAN implementation.
Main OID:
hm2WwanMib.1.3.6.1.4.1.248.11.125
132
Objects
Active
Status
5
Dependencies
Imported Objects
Objects
132 total| Object Name |
|---|
hm2WwanMibThis MIB defines the SNMP interface for Hirschmann WWAN implementation. MODULE-IDENTITY .1.3.6.1.4.1.248.11.125 |
hm2WwanMibNotifications OBJECT IDENTIFIER .1.3.6.1.4.1.248.11.125.0 |
hm2WwanRoamingActiveTrapNotification generated whenever Roaming status will become active. NOTIFICATION-TYPE .1.3.6.1.4.1.248.11.125.0.1 |
hm2WwanLtePersistenceSwitchTrapNotification generated when LTE Persistence function will perform a switch back to LTE. NOTIFICATION-TYPE .1.3.6.1.4.1.248.11.125.0.2 |
hm2WwanCelluarRegistrationFailedTrapNotification generated whenever a Cellular Network Registration failure occurs. NOTIFICATION-TYPE .1.3.6.1.4.1.248.11.125.0.3 |
hm2WwanDataConnectionSetupTrapNotification generated whenever a Cellular Data Connection will change its status. NOTIFICATION-TYPE .1.3.6.1.4.1.248.11.125.0.4 |
hm2WwanDataPlanWarningThresholdTrapNotification generated when the Data Plan Warning Threshold is reached. The trap is resent after each 25% of remaining data is consumed all the way up until the Data Plan Limit is reached. NOTIFICATION-TYPE .1.3.6.1.4.1.248.11.125.0.5 |
hm2WwanSimCardPin1StatusTrapNotification generated whenever SIM Card PIN1 access functions are used and their status changes. NOTIFICATION-TYPE .1.3.6.1.4.1.248.11.125.0.6 |
hm2WwanBackupSimFailoverConnectionTrapNotification generated whenever a data connection on the Primary SIM Card fails and a failover to Backup SIM Card is done. NOTIFICATION-TYPE .1.3.6.1.4.1.248.11.125.0.7 |
hm2WwanBackupSimFailoverRegistrationTrapNotification generated whenever a cellular network registration the Primary SIM Card fails and a failover to Backup SIM Card is done. NOTIFICATION-TYPE .1.3.6.1.4.1.248.11.125.0.8 |
hm2WwanBackupSimFailoverRoamingTrapNotification generated whenever a cellular network registration to a Roaming Carrier is detected on the Primary SIM Card and as a result a failover to the Backup SIM Card is done. NOTIFICATION-TYPE .1.3.6.1.4.1.248.11.125.0.9 |
hm2WwanBackupSimFailoverDataLimitTrapNotification generated when the current Data Plan Limit is reached and a failover to the Backup SIM Card is done. NOTIFICATION-TYPE .1.3.6.1.4.1.248.11.125.0.10 |
hm2WwanModemResetFailoverRegistrationTrapNotification generated when cellular network registration fails on the Primary SIM Card and also the fallback to Backup SIM Card registration fails. NOTIFICATION-TYPE .1.3.6.1.4.1.248.11.125.0.11 |
hm2WwanMibObjects OBJECT IDENTIFIER .1.3.6.1.4.1.248.11.125.1 |
hm2WwanGeneralGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.11.125.1.1 |
hm2WwanAdminStatusWWAN Global mode operation change.rw HmEnabledStatus (HM2-TC-MIB) .1.3.6.1.4.1.248.11.125.1.1.1 |
hm2WwanCellularSelectionCellular network selection supported combinations. 'auto' value means all supported networks (GSM/UMTS/LTE).rw Hm2CellularNetworks .1.3.6.1.4.1.248.11.125.1.1.2 |
hm2WwanLtePersistenceWhen an LTE capable device is connected to a non-LTE network it may not handover to an LTE network when one becomes available if data is being continuously transmitted or received. Enabling this function will insure that a connection over LTE will be maintained whenever LTE is available.rw HmEnabledStatus (HM2-TC-MIB) .1.3.6.1.4.1.248.11.125.1.1.4 |
hm2WwanLtePersistenceIntervalThe number of seconds after which LTE Persistence switch will be attempted. A 0 value means switch without waiting. This time interval is needed to avoid intermittent switches.rw Integer32 ( 0..3600 ) .1.3.6.1.4.1.248.11.125.1.1.5 |
hm2WwanFailoverTechnologyLevelDesired cellular technology limit. If the current cellular network technology falls below this level then failover can be triggered. This mib node is meant to be used in conjunction with hm2WwanBackupSimTechnologyLevel failover scenario.rw Hm2TechnologyLevel .1.3.6.1.4.1.248.11.125.1.1.6 |
hm2WwanBackupSimFailoverConnectionSwitch to Backup SIM card when data connection fails.rw HmEnabledStatus (HM2-TC-MIB) .1.3.6.1.4.1.248.11.125.1.1.7 |
hm2WwanBackupSimFailoverRegistrationSwitch to Backup SIM when registration fails.rw HmEnabledStatus (HM2-TC-MIB) .1.3.6.1.4.1.248.11.125.1.1.8 |
hm2WwanBackupSimFailoverRoamingSwitch to Backup SIM when roaming is detected.rw HmEnabledStatus (HM2-TC-MIB) .1.3.6.1.4.1.248.11.125.1.1.9 |
hm2WwanBackupSimFailoverDataLimitSwitch to Backup SIM card when data limit is reached and switch to Primary SIM when data limit is recovered.rw HmEnabledStatus (HM2-TC-MIB) .1.3.6.1.4.1.248.11.125.1.1.10 |
hm2WwanModemResetFailoverRegistrationAttempt a Modem reset if both Primary and Backup SIM cards report registration failures. Backup SIM card registration failure might not be needed depending if hm2WwanBackupSimFailoverRegistration is enabled or if the SIM is physical present.rw HmEnabledStatus (HM2-TC-MIB) .1.3.6.1.4.1.248.11.125.1.1.11 |
hm2WwanBackupSimTechnologyLevelSwitch to Backup SIM card when current cellular technology drops bellow a limit. Configure limit with hm2WwanFailoverTechnologyLevel.rw HmEnabledStatus (HM2-TC-MIB) .1.3.6.1.4.1.248.11.125.1.1.12 |
hm2WwanFailoverCycleBy default hm2WwanBackupSimFailoverConnection hm2WwanBackupSimFailoverRegistration will not fallback to using the Primary SIM card if failure is encountered on the Backup SIM card. This mib node will allow falling back to Primary SIM card if Backup SIM card is unable to register or create a connection. The cycled fallback will be done after 60 seconds.rw HmEnabledStatus (HM2-TC-MIB) .1.3.6.1.4.1.248.11.125.1.1.13 |
hm2WwanSetTrapA bitmap string serving as a enable/disable method for the trap events defined by the WWAN notifications. All traps are enabled by default.rw Hm2TrapBits .1.3.6.1.4.1.248.11.125.1.1.14 |
hm2WwanDataGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.11.125.1.2 |
hm2WwanDataConnectionTableThis table contains configuration options for each WWAN Data connection per SIM card. SEQUENCE OF Hm2WwanDataConnectionEntry .1.3.6.1.4.1.248.11.125.1.2.1 |
hm2WwanDataConnectionEntryThe entries of the table. Hm2WwanDataConnectionEntry .1.3.6.1.4.1.248.11.125.1.2.1.1 |
hm2WwanDataConnectionSimIdSIM ID for which this connection entry belongs to. Also used as the table's index. Integer32 .1.3.6.1.4.1.248.11.125.1.2.1.1.1 |
hm2WwanDataConnectionAdminStatusOperational mode of the connection.rw HmEnabledStatus (HM2-TC-MIB) .1.3.6.1.4.1.248.11.125.1.2.1.1.2 |
hm2WwanDataConnectionApnAccess Point Name used to identify the data connection's gateway name in the carriers network. If empty then the default APN configured on the SIM card will be used.rw SnmpAdminString .1.3.6.1.4.1.248.11.125.1.2.1.1.3 |
hm2WwanDataConnectionApnCurrentCurrent Access Point Name used for data connections. If hm2WwanDataConnectionApn is empty then the value shown here represents the automatically detected APN stored on the Sim Card.ro SnmpAdminString .1.3.6.1.4.1.248.11.125.1.2.1.1.4 |
hm2WwanDataConnectionUserUser name used for authentication when settting up a new data connection. Empty value means its not required.rw SnmpAdminString .1.3.6.1.4.1.248.11.125.1.2.1.1.5 |
hm2WwanDataConnectionPasswordPasword asociated with the user name used for authentication when settting up a new data connection. Not readable by the user.rw SnmpAdminString .1.3.6.1.4.1.248.11.125.1.2.1.1.6 |
hm2WwanDataConnectionAuthThe type of authentication used when setting up a data connection.rw Hm2AuthType .1.3.6.1.4.1.248.11.125.1.2.1.1.7 |
hm2WwanDataConnectionPdpTypeThe IP type of the data connection to set up. It can be IPv4 or IPv6. Currently only IPv4 is supported.rw Hm2PdpType .1.3.6.1.4.1.248.11.125.1.2.1.1.8 |
hm2WwanDataConnectionIpAddressTypehm2WwanDataConnectionIpAddress value type, either IPv4 or IPv6.rw InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.248.11.125.1.2.1.1.9 |
hm2WwanDataConnectionIpAddressManual IP address to be used for configuring a new data connection. If 0.0.0.0 then a dynamic IP Address will be assigned by the carrier.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.248.11.125.1.2.1.1.10 |
hm2WwanDataConnectionDnsPrimaryTypehm2WwanDataConnectionDnsPrimary value type, either IPv4 or IPv6.rw InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.248.11.125.1.2.1.1.11 |
hm2WwanDataConnectionDnsPrimaryManual IP address to be used for configuring the primary DNS server address for the data connection. If 0.0.0.0 then a dynamic DNS IP Address will be assigned by the carrier.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.248.11.125.1.2.1.1.12 |
hm2WwanDataConnectionDnsSecondaryTypehm2WwanDataConnectionDnsSecondary value type, either IPv4 or IPv6.rw InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.248.11.125.1.2.1.1.13 |
hm2WwanDataConnectionDnsSecondaryManual IP address to be used for configuring the secondary DNS server address for the data connection. If 0.0.0.0 then a dynamic DNS IP Address will be assigned by the carrier.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.248.11.125.1.2.1.1.14 |
hm2WwanDataConnectionIpAddressCurrentTypehm2WwanDataConnectionIpAddressCurrent value type, either IPv4 or IPv6.ro InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.248.11.125.1.2.1.1.15 |
hm2WwanDataConnectionIpAddressCurrentThe IP Address that the WWAN data interface is currently using.ro InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.248.11.125.1.2.1.1.16 |
hm2WwanDataConnectionDnsPrimaryCurrentTypehm2WwanDataConnectionDnsPrimaryCurrent value type, either IPv4 or IPv6.ro InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.248.11.125.1.2.1.1.17 |
hm2WwanDataConnectionDnsPrimaryCurrentThe Primary DNS Address that the WWAN data interface is currently using.ro InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.248.11.125.1.2.1.1.18 |
hm2WwanDataConnectionDnsSecondaryCurrentTypehm2WwanDataConnectionDnsSecondaryCurrent value type, either IPv4 or IPv6.ro InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.248.11.125.1.2.1.1.19 |
hm2WwanDataConnectionDnsSecondaryCurrentThe Secondary DNS Address that the WWAN data interface is currently using.ro InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.248.11.125.1.2.1.1.20 |
hm2WwanDataConnectionMtuMaximum Transmision Unit used when sending IP packets over the WWAN data interface.rw Integer32 .1.3.6.1.4.1.248.11.125.1.2.1.1.21 |
hm2WwanDataConnectionFailedRetryHow many times should a failed WWAN data connection attempt to try reconnecting before aborting and using fallback options or logging error. A value of 0 means no retry attempts and a value of -1 means 'infinite' attempts.rw Integer32 (-1..32) .1.3.6.1.4.1.248.11.125.1.2.1.1.22 |
hm2WwanDataConnectionFailedRetryCurrentThe current number o data reconnect attempts made. Can only be lower or equal to hm2WwanDataConnectionFailedRetry. Value 0 means no retries have been made.ro Integer32 .1.3.6.1.4.1.248.11.125.1.2.1.1.23 |
hm2WwanDataConnectionStatusCurrent status of this WWAN Data connection. If in 'Error' state then a reason for the error will be found under hm2WwanDataConnectionStatusErrorReason.ro Hm2ConnectionStatus .1.3.6.1.4.1.248.11.125.1.2.1.1.24 |
hm2WwanDataConnectionStatusErrorReasonThe reason why this WWAN Data connection is in 'Error' state.ro HmLargeDisplayString (HM2-TC-MIB) .1.3.6.1.4.1.248.11.125.1.2.1.1.25 |
hm2WwanDataConnectionActivatedCountHow many times this WWAN Data connection was successfuly established.ro Unsigned32 .1.3.6.1.4.1.248.11.125.1.2.1.1.26 |
hm2WwanDataConnectionStartTimeTime in seconds since Jan 1, 1970.ro Unsigned32 .1.3.6.1.4.1.248.11.125.1.2.1.1.27 |
hm2WwanDataConnectionUpTimeTime in seconds since this connection is active.ro Unsigned32 .1.3.6.1.4.1.248.11.125.1.2.1.1.28 |
hm2WwanDataConnectionTotalUpTimeTotal time in which this connection was active.ro Unsigned32 .1.3.6.1.4.1.248.11.125.1.2.1.1.29 |
hm2WwanDataPlanTableThis table contains configuration options for each WWAN Data Plan per SIM card. SEQUENCE OF Hm2WwanDataPlanEntry .1.3.6.1.4.1.248.11.125.1.2.2 |
hm2WwanDataPlanEntryThe entries of the table. Hm2WwanDataPlanEntry .1.3.6.1.4.1.248.11.125.1.2.2.1 |
hm2WwanDataPlanSimIdSIM ID for which this connection entry belongs. Also used as the table's index. Integer32 .1.3.6.1.4.1.248.11.125.1.2.2.1.1 |
hm2WwanDataPlanMonthlyLimitThe amount of data that the carrier will charge as per a WWAN data contract per month. A value 0 means unlimited.rw Unsigned32 .1.3.6.1.4.1.248.11.125.1.2.2.1.2 |
hm2WwanDataPlanLimitMeasureUnitWhich measure unit is used to interpret the volume of the data traffic. Possible units are: Kilobytes, Megabytes, Gigabytes.rw Hm2LimitUnit .1.3.6.1.4.1.248.11.125.1.2.2.1.3 |
hm2WwanDataPlanWarningThresholdThe percentage of the volume of data that when reached will generate a warning. A value of 0 will disable the warning.rw Integer32 .1.3.6.1.4.1.248.11.125.1.2.2.1.4 |
hm2WwanDataPlanResetManually reset the data plan counters. Only the value 'action(2)' can be written and when read 'noop(1)' will always be returned.rw HmActionValue (HM2-TC-MIB) .1.3.6.1.4.1.248.11.125.1.2.2.1.5 |
hm2WwanDataPlanResetDayWhich day of the month will be used to auto reset the data plan counters. A value of 0 will disable the reset action. The reset action will be performed at 00:00am in the selected day.rw Integer32 .1.3.6.1.4.1.248.11.125.1.2.2.1.6 |
hm2WwanDataPlanLastResetTime in seconds since Jan 1st, 1970 when the last data plan counters were resetted.ro HmTimeSeconds1970 (HM2-TC-MIB) .1.3.6.1.4.1.248.11.125.1.2.2.1.7 |
hm2WwanDataPlanCutoffThresholdThe percentage of the volume of used data that when reached will completely disable any data connections associated with this SIM ID. A value of 0 will disable the cutoff.rw Integer32 .1.3.6.1.4.1.248.11.125.1.2.2.1.8 |
hm2WwanDataPlanMonthlyUsageTxThe amount of data that was transmitted since last reset. The measure unit is the same as hm2WwanDataPlanLimitMeasureUnit.ro Counter64 .1.3.6.1.4.1.248.11.125.1.2.2.1.9 |
hm2WwanDataPlanMonthlyUsageRxThe amount of data that was received since last reset. The measure unit is the same as hm2WwanDataPlanLimitMeasureUnit.ro Counter64 .1.3.6.1.4.1.248.11.125.1.2.2.1.10 |
hm2WwanDataPacketStatsTableThis table contains packet statistics for each WWAN Data connection per SIM card. SEQUENCE OF Hm2WwanDataPacketStatsEntry .1.3.6.1.4.1.248.11.125.1.2.3 |
hm2WwanDataPacketStatsEntryThe entries of the table. Hm2WwanDataPacketStatsEntry .1.3.6.1.4.1.248.11.125.1.2.3.1 |
hm2WwanDataPacketStatsSimIdSIM ID for which this data connection packet statistics entry belongs to. Also used as the table's index. Integer32 .1.3.6.1.4.1.248.11.125.1.2.3.1.1 |
hm2WwanDataPacketStatsTxOkThe number of successfully transmitted data packets.ro Counter64 .1.3.6.1.4.1.248.11.125.1.2.3.1.2 |
hm2WwanDataPacketStatsRxOkThe number of successfully received data packets.ro Counter64 .1.3.6.1.4.1.248.11.125.1.2.3.1.3 |
hm2WwanDataPacketStatsTxErrorsThe number of errors encountered during packet transmission.ro Counter64 .1.3.6.1.4.1.248.11.125.1.2.3.1.4 |
hm2WwanDataPacketStatsRxErrorsThe number of errors encountered during packet reception.ro Counter64 .1.3.6.1.4.1.248.11.125.1.2.3.1.5 |
hm2WwanDataPacketStatsTxOverflowsThe number of overflows encountered during packet transmission.ro Counter64 .1.3.6.1.4.1.248.11.125.1.2.3.1.6 |
hm2WwanDataPacketStatsRxOverflowsThe number of overflows encountered during packet reception.ro Counter64 .1.3.6.1.4.1.248.11.125.1.2.3.1.7 |
hm2WwanDataPacketStatsTxBytesOkThe number of successfully transmitted bytes.ro Counter64 .1.3.6.1.4.1.248.11.125.1.2.3.1.8 |
hm2WwanDataPacketStatsRxBytesOkThe number of successfully received bytes.ro Counter64 .1.3.6.1.4.1.248.11.125.1.2.3.1.9 |
hm2WwanDataPacketStatsTxDroppedThe number of packets dropped during transmission.ro Counter64 .1.3.6.1.4.1.248.11.125.1.2.3.1.10 |
hm2WwanDataPacketStatsRxDroppedThe number of packets dropped during reception.ro Counter64 .1.3.6.1.4.1.248.11.125.1.2.3.1.11 |
hm2WwanSimCardGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.11.125.1.3 |
hm2WwanSimCardTableThis table contains configuration options for each WWAN SIM card. SEQUENCE OF Hm2WwanSimCardEntry .1.3.6.1.4.1.248.11.125.1.3.1 |
hm2WwanSimCardEntryThe entries of the table. Hm2WwanSimCardEntry .1.3.6.1.4.1.248.11.125.1.3.1.1 |
hm2WwanSimCardSimIdSIM ID for which this connection entry belongs. Also used as the table's index. Integer32 .1.3.6.1.4.1.248.11.125.1.3.1.1.1 |
hm2WwanSimCardAdminStatusSim Card enable/disable function.rw HmEnabledStatus (HM2-TC-MIB) .1.3.6.1.4.1.248.11.125.1.3.1.1.2 |
hm2WwanSimCardRoleThe role this Sim Card will be assigned. The role is important for failover scenarios configured under General Configuration Group. 'auto' setting will automatically choose a role.rw Hm2SimCardRole .1.3.6.1.4.1.248.11.125.1.3.1.1.3 |
hm2WwanSimCardRoleCurrentThe role this Sim Card is currently using.ro Hm2SimCardRole .1.3.6.1.4.1.248.11.125.1.3.1.1.4 |
hm2WwanSimCardStatusSim Card Status information: * simPresent: the SIM is physicaly present. * simAbsent: the SIM is physicaly absent. * simLocked: the SIM is physicaly present but was not unlocked using PIN1. * simUnlocked: the SIM is physicaly present and it was unlocked unsing PIN1. * simInactive: the sim is physicaly present but it is not used for data connections. * simActive: the sim is physicaly present and is used for data connections.ro Hm2SimCardStatus .1.3.6.1.4.1.248.11.125.1.3.1.1.5 |
hm2WwanSimCardSetActiveManual operation to set the active status of this sim card. When in active state this sim card will be used for establishing data connections.rw HmActionValue (HM2-TC-MIB) .1.3.6.1.4.1.248.11.125.1.3.1.1.6 |
hm2WwanSimCardPin1Sim Card's PIN1 code. PIN1 is used to unlock main Sim functions which will allow Network Carrier Registration.rw SnmpAdminString .1.3.6.1.4.1.248.11.125.1.3.1.1.7 |
hm2WwanSimCardPin1ModeAllows to enable or disable PIN1 code. With PIN1 disabled the Sim Card will automatically unlock all it's functions.rw HmEnabledStatus (HM2-TC-MIB) .1.3.6.1.4.1.248.11.125.1.3.1.1.8 |
hm2WwanSimCardPin1StatusPin1 status information: * NotVerified: Pin1 was not verified. * Verified: Pin1 was successfuly verified. * Blocked: Wrong Pin1 was used too many times and the Sim Card blocked it. * Disabled: Pin1 was manually disabled or the Sim Card does not requires it. * WrongCode: The configured Pin1 code is not accepted by the Sim Card unlock function.ro Hm2Pin1Status .1.3.6.1.4.1.248.11.125.1.3.1.1.9 |
hm2WwanSimCardPin1VerifyTriesThe amount of times a wrong Pin1 code can be used to unlock the Sim Card until it is blocked.ro Integer32 .1.3.6.1.4.1.248.11.125.1.3.1.1.10 |
hm2WwanSimCardPin1UnblockTriesThe amount of times a wrong PUK1 code can be entered to unblock a PIN1 code.ro Integer32 .1.3.6.1.4.1.248.11.125.1.3.1.1.11 |
hm2WwanSimCardPuk1PUK1 code is used to unblock a PIN1 code. Writing a PUK1 value will attempt to unblock a PIN1 code if the PIN1 code is in 'Blocked' state. PUK1 code will not be saved. hm2WwanSimCardPin1UnblockTries is a counter on how many times a wrong PUK1 code can be entered. Empty value write operation will be ignored. New PIN code configured during the unblock operation will be the current PIN1 stored in hm2WwanSimCardPin1 mib.rw SnmpAdminString .1.3.6.1.4.1.248.11.125.1.3.1.1.12 |
hm2WwanSimCardRoamingModeRoaming will allow the modem to perform registration with carriers other than the one that emitted the current SIM card. Data connections established when attached to Roaming partners will probably incur additional costs.rw HmEnabledStatus (HM2-TC-MIB) .1.3.6.1.4.1.248.11.125.1.3.1.1.13 |
hm2WwanSimCardIccidIntegrated Circuit Card Identifier is the international SIM's identifier. This value is preserved over reboots so that when a new SIM is inserted the operation can be detected and the settings relevant for the old SIM can be resetted. The user can only read this mib value.rw SnmpAdminString .1.3.6.1.4.1.248.11.125.1.3.1.1.14 |
hm2WwanSimCardImsiInternational Mobile Subscriber Identity is an individual identifier on operator networks. Mobile network operators connect mobile phone calls and communicate with their market SIM cards using their IMSIs.ro SnmpAdminString .1.3.6.1.4.1.248.11.125.1.3.1.1.15 |
hm2WwanInformationGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.11.125.1.4 |
hm2WwanCellularInformationGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.11.125.1.4.1 |
hm2WwanCellularActiveSimIdThe Sim Card id for the current active SIM.ro Integer32 .1.3.6.1.4.1.248.11.125.1.4.1.1 |
hm2WwanCellularRegistrationThe current status of the Sim's Carrier Registration.ro Hm2RegistrationStatus .1.3.6.1.4.1.248.11.125.1.4.1.2 |
hm2WwanCellularOperatorNetwork Operator Namero SnmpAdminString .1.3.6.1.4.1.248.11.125.1.4.1.3 |
hm2WwanCellularNetworkCurrent Cellular Network Technology being used.ro Hm2CellularNetworks .1.3.6.1.4.1.248.11.125.1.4.1.4 |
hm2WwanCellularMccMobile Country Code is a 3 digits code used to identify the country where the Public Land Mobile Network (PLMN) resides.ro Integer32 .1.3.6.1.4.1.248.11.125.1.4.1.5 |
hm2WwanCellularMncMobile Network Code is a 2 to 3 digits code used to identify the Public Land Mobile Network (PLMN) in that country.ro Integer32 .1.3.6.1.4.1.248.11.125.1.4.1.6 |
hm2WwanCellularLacLocation area code together with PLMN (MCC + MNC) creates an internationally unique identifier known as Location Area Identity (LAI). The LAI is used for location updating of the mobile subscribers.ro Integer32 .1.3.6.1.4.1.248.11.125.1.4.1.7 |
hm2WwanCellularBsicBase Station Identity Code is a code used in WWAN networks to uniquely identify a base station.ro Integer32 .1.3.6.1.4.1.248.11.125.1.4.1.8 |
hm2WwanCellularCellIdThe identifier of the current used WWAN Cell.ro Integer32 .1.3.6.1.4.1.248.11.125.1.4.1.9 |
hm2WwanCellularBandThe current Cellular Band used for radio transmissions.ro Integer32 .1.3.6.1.4.1.248.11.125.1.4.1.10 |
hm2WwanCellularChannelThe current channel number within the Cellular Band used for radio transmissions.ro Integer32 .1.3.6.1.4.1.248.11.125.1.4.1.11 |
hm2WwanCellularSignalStrengthIn GSM/UMTS mobile networks signal strength is based on RSSI (Received Signal Strength Indication) value measuring the power level being received by the antena. The higher the RSSI the stronger the signal.ro Integer32 .1.3.6.1.4.1.248.11.125.1.4.1.12 |
hm2WwanCellularSignalStrengthLteIn LTE mobile networks signal strength is based on RSRP (Reference Signal Received Power) value.ro Integer32 .1.3.6.1.4.1.248.11.125.1.4.1.13 |
hm2WwanCellularSignalQualityUMTS signal quality indicator based on ECIO (Energy to Interference Ratio).ro Integer32 .1.3.6.1.4.1.248.11.125.1.4.1.14 |
hm2WwanCellularSignalQualityLteLTE signal quality indicator based on RSRQ (Reference Signal Received Quality).ro Integer32 .1.3.6.1.4.1.248.11.125.1.4.1.15 |
hm2WwanCellularRscpUMTS Received Signal Code Power is used as an indication of signal strength, as a handover criterion, in downlink power control and to calculate path loss.ro Integer32 .1.3.6.1.4.1.248.11.125.1.4.1.16 |
hm2WwanCellularRoamingStatusCurrent Roaming status: * Home: registration done in home network. * Roaming: registration done in partner network in roaming mode. Roaming has to be admin enabled. * RoamingDisabled: no home network detected and Roaming is admin disabled.ro Hm2RoamingStatus .1.3.6.1.4.1.248.11.125.1.4.1.17 |
hm2WwanCellularBitErrorRateCellular transmission error rate displayed in percentage.ro Integer32 .1.3.6.1.4.1.248.11.125.1.4.1.18 |
hm2WwanCellularCurrentTxRateCurrent channel TX rate displayed in kbps.ro Unsigned32 .1.3.6.1.4.1.248.11.125.1.4.1.19 |
hm2WwanCellularCurrentRxRateCurrent channel RX rate displayed in kbps.ro Unsigned32 .1.3.6.1.4.1.248.11.125.1.4.1.20 |
hm2WwanCellularMaxTxRateMaximum channel TX rate that can be achieved, displayed in kbps.ro Unsigned32 .1.3.6.1.4.1.248.11.125.1.4.1.21 |
hm2WwanCellularMaxRxRateMaximum channel RX rate that can be achieved, displayed in kbps.ro Unsigned32 .1.3.6.1.4.1.248.11.125.1.4.1.22 |
hm2WwanModemInformationGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.11.125.1.4.2 |
hm2WwanModemManufacturerRadio Modem Manufacturerro SnmpAdminString .1.3.6.1.4.1.248.11.125.1.4.2.1 |
hm2WwanModemModelThe model of the Radio Modem.ro SnmpAdminString .1.3.6.1.4.1.248.11.125.1.4.2.2 |
hm2WwanModemRevisionModem Software version and revision.ro SnmpAdminString .1.3.6.1.4.1.248.11.125.1.4.2.3 |
hm2WwanModemImeiInternation Mobile Equipment Identity is a unique number given to mobile capable devices.ro SnmpAdminString .1.3.6.1.4.1.248.11.125.1.4.2.4 |