HM2-NETCONFIG-MIB
Hirschmann Network Configuration MIB. Copyright (C) 2012. All Rights Reserved.
Main OID:
hm2NetConfigMib.1.3.6.1.4.1.248.11.20
60
Objects
Active
Status
6
Dependencies
Imported Objects
Objects
60 total| Object Name |
|---|
hm2NetConfigMibHirschmann Network Configuration MIB.
Copyright (C) 2012. All Rights Reserved. MODULE-IDENTITY .1.3.6.1.4.1.248.11.20 |
IMPORTSHirschmann Network Configuration MIB.
Copyright (C) 2012. All Rights Reserved. NOTIFICATION-TYPE .1.3.6.1.4.1.248.11.20 |
hm2NetConfigMibNotifications OBJECT IDENTIFIER .1.3.6.1.4.1.248.11.20.0 |
hm2NetACDNotificationThis trap reports an address conflict. NOTIFICATION-TYPE .1.3.6.1.4.1.248.11.20.0.1 |
hm2NetMacACDNotificationThis trap reports a MAC address conflict with it's own MAC address. NOTIFICATION-TYPE .1.3.6.1.4.1.248.11.20.0.2 |
hm2NetConfigMibObjects OBJECT IDENTIFIER .1.3.6.1.4.1.248.11.20.1 |
hm2NetStaticGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.11.20.1.1 |
hm2NetConfigProtocolThe switch's network configuration protocol.
The default value is dependent of the device type.rw Enumeration .1.3.6.1.4.1.248.11.20.1.1.1 |
hm2NetLocalIPAddrTypeLocal IP address type.rw InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.248.11.20.1.1.2 |
hm2NetLocalIPAddrIP address of the management agent board.
Changing this value will take effect after activating
with hm2NetAction.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.248.11.20.1.1.3 |
hm2NetPrefixLengthThe length of the IP netmask.rw InetAddressPrefixLength (INET-ADDRESS-MIB) .1.3.6.1.4.1.248.11.20.1.1.4 |
hm2NetGatewayIPAddrTypeDefault gateway IP address type.rw InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.248.11.20.1.1.5 |
hm2NetGatewayIPAddrIP address of the default gateway.
Changing this value will take effect after activating
with hm2NetAction.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.248.11.20.1.1.6 |
hm2NetVlanIDVLAN-ID of the IP protocol stack. The VLAN-ID value means
that only traffic of the appropriate VLAN is accepted and
outgoing traffic uses this VLAN-ID.rw Integer32 .1.3.6.1.4.1.248.11.20.1.1.7 |
hm2NetVlanPriorityVLAN Priority which is used in management replies.rw Integer32 .1.3.6.1.4.1.248.11.20.1.1.8 |
hm2NetIpDscpPriorityIP DSCP value which is used in management replies.rw Integer32 .1.3.6.1.4.1.248.11.20.1.1.9 |
hm2NetMgmtPortThe port number of the Ethernet port, which gets the access to
the switch management.
If the value is set to 0, the access to the switch management is
permitted from all ports of the switch.
This object is only applicable for embedded switches which are
integrated into customer devices.rw Integer32 .1.3.6.1.4.1.248.11.20.1.1.10 |
hm2NetDHCPClientIdThe identifier string that is currently used by the client in the
request packets to the server for obtaining lease information.ro DisplayString .1.3.6.1.4.1.248.11.20.1.1.11 |
hm2NetActionThis object, when read, always returns a value of other(1).
Setting the object to activate(2) causes a reconfiguration
of the IP protocol stack with the current values of
hm2NetLocalIPAddr, hm2NetGatewayIPAddr and hm2NetMask.rw Enumeration .1.3.6.1.4.1.248.11.20.1.1.50 |
hm2NetACDGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.11.20.1.2 |
hm2NetACDStatusSets the status of the ip address conflict detection mechanism on this device.
With activating the ACD status an internal check of duplicated IP-addresses is
enabled.rw HmEnabledStatus (HM2-TC-MIB) .1.3.6.1.4.1.248.11.20.1.2.1 |
hm2NetACDDetectionModeSets the mode of the ip address conflict detection mechanism on this device.
activeAndPassive (1): Both active and passive detection are active.
activeDetectionOnly (2): During configuration of a local ip address
the device actively probes the network for this ip address.
passiveDetectionOnly (3): The device listens passively on the network
if another device with an already locally configured ip address appears.
In this case the own ip address is actively defended by transmitting gratituous ARP's.rw Enumeration .1.3.6.1.4.1.248.11.20.1.2.2 |
hm2NetACDOngoingProbeStatusIf enabled, the device sends periodic ARP or NDP probes every 90-120 seconds.rw HmEnabledStatus (HM2-TC-MIB) .1.3.6.1.4.1.248.11.20.1.2.3 |
hm2NetACDDelayTime gap between ARP or NDP probes being sent.rw Integer32 .1.3.6.1.4.1.248.11.20.1.2.5 |
hm2NetACDReleaseDelayDelay in seconds to the next ARP or NDP probe cycle after an ip address conflict was detected.rw Integer32 .1.3.6.1.4.1.248.11.20.1.2.7 |
hm2NetACDMaxProtectionThe number of ARP announcement packets (gratuitous ARP packets) in passive(ongoing) mode to be received
within hm2NetACDProtectInterval until the agent detects this as a conflict.rw Integer32 .1.3.6.1.4.1.248.11.20.1.2.9 |
hm2NetACDProtectIntervalDelay in milliseconds between two protections. See also hm2NetACDMaxProtection.rw Integer32 .1.3.6.1.4.1.248.11.20.1.2.11 |
hm2NetACDFaultStatetrue(1) if an active address conflict is detected.
false(2) if no present address conflict.ro Enumeration .1.3.6.1.4.1.248.11.20.1.2.13 |
hm2NetACDTrapEnableIf enabled this trap reports an address conflict.rw HmEnabledStatus (HM2-TC-MIB) .1.3.6.1.4.1.248.11.20.1.2.15 |
hm2NetACDAddrTableThis table contains address conflict detection information
on the local system known to this agent. SEQUENCE OF Hm2NetACDAddrEntry .1.3.6.1.4.1.248.11.20.1.2.20 |
hm2NetACDAddrEntryIP Address conflict detection information about a particular
address on the local system known to this agent.
There may be multiple addresses configured on the system.
Entries may be created and deleted in this table by the
agent. Hm2NetACDAddrEntry .1.3.6.1.4.1.248.11.20.1.2.20.1 |
hm2NetACDTimeMarkA TimeFilter for this entry. See the TimeFilter textual
convention in IETF RFC 2021 and
http://www.ietf.org/IESG/Implementations/RFC2021-Implementation.txt
to see how TimeFilter works.ro TimeFilter (RMON2-MIB) .1.3.6.1.4.1.248.11.20.1.2.20.1.1 |
hm2NetACDAddrTypeLocal IP Address Typero InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.248.11.20.1.2.20.1.3 |
hm2NetACDIPAddrIP address used to identify the management address
component associated with the local system.ro InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.248.11.20.1.2.20.1.5 |
hm2NetACDMACThe physical address of the device that was detected
causing the ip address conflict.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.248.11.20.1.2.20.1.7 |
hm2NetACDifIndexThe interface index on the local system
where the ip address conflict was detected.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.248.11.20.1.2.20.1.9 |
hm2NetMacGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.11.20.1.3 |
hm2NetLocalBurnedInMacAddrPhysical base address (MAC address) of the agent.
This is the burned in MAC address from the productionro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.248.11.20.1.3.1 |
hm2NetLocalAdminMacAddressThe switch's network locally administered MAC address.
This is the locally MAC address from the administrator. If
the hm2NetLocalAdminMacAddress is nonzero, the device starts
with this MAC address at the next boot.
If the variable is changed, they must be stored by the
configuration manager.
A MAC address with a set multicast bit will not be acceptedrw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.248.11.20.1.3.2 |
hm2NetMacAddressTypeShows the currently used MAC address at boot time.
The device starts with the burned in MAC address when
hm2NetLocalAdminMacAddress is zero, otherwise with the
Local-Admin-MAC-Address.ro Enumeration .1.3.6.1.4.1.248.11.20.1.3.3 |
hm2NetHiDiscoveryGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.11.20.1.4 |
hm2NetHiDiscoveryOperationEnables/disables the HiDiscovery protocol
on this device.
This protocol allows a remote host to detect
devices without an IP configuration.
It also allows the host to set IP parameters,
like the ip address, the netmask and
the gateway address.rw HmEnabledStatus (HM2-TC-MIB) .1.3.6.1.4.1.248.11.20.1.4.1 |
hm2NetHiDiscoveryModeIn the read only mode only detecting and
reading the IP parameters is permitted.
The read write mode gives full access to
the device.rw Enumeration .1.3.6.1.4.1.248.11.20.1.4.2 |
hm2NetHiDiscoveryBlinkingEnables/disables the HiDiscovery blinking sequence
on this device. This object will not be saved.rw HmEnabledStatus (HM2-TC-MIB) .1.3.6.1.4.1.248.11.20.1.4.3 |
hm2NetHiDiscoveryProtocolShows the HiDiscovery protocols supported by the device.ro Bits .1.3.6.1.4.1.248.11.20.1.4.4 |
hm2NetHiDiscoveryRelayRelay/bridge HiDiscovery frames.rw HmEnabledStatus (HM2-TC-MIB) .1.3.6.1.4.1.248.11.20.1.4.5 |
hm2NetMacACDGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.11.20.1.5 |
hm2NetMacACDStatusSets the status of the MAC address conflict detection mechanism on this device.rw HmEnabledStatus (HM2-TC-MIB) .1.3.6.1.4.1.248.11.20.1.5.1 |
hm2NetMacACDConflictAddressMAC address in case of a conflict.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.248.11.20.1.5.2 |
hm2NetOobMgmtGroup OBJECT IDENTIFIER .1.3.6.1.4.1.248.11.20.1.6 |
hm2NetOobMgmtAdminStateThe status of the Out-of-band management on this device.rw HmEnabledStatus (HM2-TC-MIB) .1.3.6.1.4.1.248.11.20.1.6.1 |
hm2NetOobMgmtProtocolThe switch's out-of-band network configuration protocol.
The default value is dependent of the device type.rw Enumeration .1.3.6.1.4.1.248.11.20.1.6.2 |
hm2NetOobMgmtIPAddrTypeOut-of-band IP address type.rw InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.248.11.20.1.6.3 |
hm2NetOobMgmtIPAddrOut-of-band IP address of the management agent board.
Changing this value will take effect after activating
with hm2NetOobMgmtAction.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.248.11.20.1.6.4 |
hm2NetOobMgmtPrefixLengthThe length of the IP netmask.rw InetAddressPrefixLength (INET-ADDRESS-MIB) .1.3.6.1.4.1.248.11.20.1.6.5 |
hm2NetOobMgmtGatewayIPAddrTypeOut-of-band default gateway IP address type.rw InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.248.11.20.1.6.6 |
hm2NetOobMgmtGatewayIPAddrOut-of-band IP address of the default gateway.
Changing this value will take effect after activating
with hm2NetOobMgmtAction.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.248.11.20.1.6.7 |
hm2NetOobMgmtMacAddressOut-of-band MAC address of the interface.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.248.11.20.1.6.8 |
hm2NetOobMgmtOperStateOut-of-band interface current operational state.ro Enumeration .1.3.6.1.4.1.248.11.20.1.6.9 |
hm2NetOobMgmtActionThis object, when read, always returns a value of other(1).
Setting the object to activate(2) causes a reconfiguration
of the out-of-band IP protocol stack with the current values of
hm2NetOobMgmtLocalIPAddr, hm2NetOobMgmtPrefixLength and hm2NetOobMgmtGatewayIPAddr.rw Enumeration .1.3.6.1.4.1.248.11.20.1.6.50 |