CISCO-LWAPP-DOT11-CLIENT-MIB
AI MIB Summary
The CISCO-LWAPP-DOT11-CLIENT-MIB enables Central Controllers to monitor and manage the configuration and operational state of 802.11 Mobile Nodes (clients) associated with Cisco Lightweight Access Points within an LWAPP architecture. It provides specific metrics for tracking client associations, BSS parameters, and the encapsulation of 802.11 frames within LWAPP tunnels for centralized processing.
This MIB is intended to be implemented on all those devices operating as Central controllers, that terminate the Light Weight Access Point Protocol tunnel from Cisco Light-weight LWAPP Access Points.
Information provided by this MIB is about the configuration and monitoring of 802.11 wireless clients in the network.
The relationship between CC and the LWAPP APs can be depicted as follows:
+......+ +......+ +......+ +......+
+ + + + + + + +
+ CC + + CC + + CC + + CC +
+ + + + + + + +
+......+ +......+ +......+ +......+
.. . . . .. . . . . . . . . . . . . . . . . . . . . . . .
+......+ +......+ +......+ +......+ +......+
+ + + + + + + + + +
+ AP + + AP + + AP + + AP + + AP +
+ + + + + + + + + +
+......+ +......+ +......+ +......+ +......+
. . . . . . . . . . . . . . . . . . . . . . . .
+......+ +......+ +......+ +......+ +......+
+ + + + + + + + + +
+ MN + + MN + + MN + + MN + + MN +
+ + + + + + + + + +
+......+ +......+ +......+ +......+ +......+
The LWAPP tunnel exists between the controller and the APs. The MNs communicate with the APs through the protocol defined by the 802.11 standard.
LWAPP APs, upon bootup, discover and join one of the controllers and the controller pushes the configuration, that includes the WLAN parameters, to the LWAPP APs. The APs then encapsulate all the 802.11 frames from wireless clients inside LWAPP frames and forward the LWAPP frames to the controller.
GLOSSARY
Access Point ( AP )
An entity that contains an 802.11 medium access control ( MAC ) and physical layer ( PHY ) interface and provides access to the distribution services via the wireless medium for associated clients.
LWAPP APs encapsulate all the 802.11 frames in LWAPP frames and sends them to the controller to which it is logically connected.
Basic Service Set ( BSS )
Coverage area of one access point is called a BSS. An access point (AP) acts as a master to control the clients within that BSS.
Clear To Send (CTS)
Refer to the description of RTS.
Light Weight Access Point Protocol ( LWAPP )
This is a generic protocol that defines the communication between the Access Points and the Central Controller.
MAC Service Data Units ( MSDU )
The MSDU is that unit of data received from the logical link control ( LLC ) sub-layer which lies above the medium access control ( MAC ) sub-layer in a protocol stack.
Message Integrity Code ( MIC )
A value generated by a symmetric key cryptographic function. If the input data are changed, a new value cannot be correctly computed without knowledge of the symmetric key. Thus, the secret key protects the input data from undetectable alteration.
Mobile Node ( MN )
A roaming 802.11 wireless device in a wireless network associated with an access point. Mobile Node, Mobile Station(Ms) and client are used interchangeably.
Request To Send ( RTS )
A client wishing to send data initiates the process by sending a Request To Send (RTS) frame. The destination client replies with a Clear To Send (CTS) frame.
Wireless local-area network ( WLAN ) A local-area network that uses high-frequency radio waves rather than wires to communicate between nodes.
Service Set Identifier (SSID) A service set identifier is a name that identifies a particular 802.11 wireless LAN. A client device receives broadcast messages from all access points within range advertising their SSIDs. The client device can then either manually or automatically based on configuration select the network with which to associate. The SSID can be up to 32 characters long.
Hybrid Remote Edge Access Point (HREAP) HREAP is a wireless solution for branch office and remote office deployments. It enables customers to configure and control access points in a branch or remote office from the corporate office through a wide area network (WAN) link without deploying a controller in each office. HREAP is also known as flexconnect.
Workgroup Bridge ( WGB ) A WGB can provide a wireless infrastructure connection for a Ethernet-enabled devices. Devices that do not have a wireless client adapter in order to connect to the wireless network can be connected to a WGB through Ethernet port.
KTS (Key Telephone System)
Key Telephone System is an alternative to a private branch exchange (PBX) phone system. A KTS is equipped with several buttons that allow a caller to directly select outgoing lines or incoming calls, and use intercom and conference facilities.
REFERENCE
[1] Wireless LAN Medium Access Control ( MAC ) and Physical Layer ( PHY ) Specifications
[2] Draft-obara-capwap-lwapp-00.txt, IETF Light Weight Access Point Protocol
Main OID:
ciscoLwappDot11ClientMIB.1.3.6.1.4.1.9.9.599
177
Objects
Active
Status
11
Dependencies
Imported Objects
Objects
177 total| Object Name |
|---|
ciscoLwappDot11ClientMIBThis MIB is intended to be implemented on all those
devices operating as Central controllers, that
terminate the Light Weight Access Point Protocol
tunnel from Cisco Light-weight LWAPP Access Points.
Information provided by this MIB is about the
configuration and monitoring of 802.11 wireless
clients in the network.
The relationship between CC and the LWAPP APs
can be depicted as follows:
+......+ +......+ +......+ +......+
+ + + + + + + +
+ CC + + CC + + CC + + CC +
+ + + + + + + +
+......+ +......+ +......+ +......+
.. . . .
.. . . .
. . . . .
. . . . .
. . . . .
. . . . .
+......+ +......+ +......+ +......+ +......+
+ + + + + + + + + +
+ AP + + AP + + AP + + AP + + AP +
+ + + + + + + + + +
+......+ +......+ +......+ +......+ +......+
. . . .
. . . . .
. . . . .
. . . . .
. . . . .
+......+ +......+ +......+ +......+ +......+
+ + + + + + + + + +
+ MN + + MN + + MN + + MN + + MN +
+ + + + + + + + + +
+......+ +......+ +......+ +......+ +......+
The LWAPP tunnel exists between the controller and
the APs. The MNs communicate with the APs through
the protocol defined by the 802.11 standard.
LWAPP APs, upon bootup, discover and join one of the
controllers and the controller pushes the configuration,
that includes the WLAN parameters, to the LWAPP APs.
The APs then encapsulate all the 802.11 frames from
wireless clients inside LWAPP frames and forward
the LWAPP frames to the controller.
GLOSSARY
Access Point ( AP )
An entity that contains an 802.11 medium access
control ( MAC ) and physical layer ( PHY ) interface
and provides access to the distribution services via
the wireless medium for associated clients.
LWAPP APs encapsulate all the 802.11 frames in
LWAPP frames and sends them to the controller to which
it is logically connected.
Basic Service Set ( BSS )
Coverage area of one access point is called a BSS. An
access point (AP) acts as a master to control the
clients within that BSS.
Clear To Send (CTS)
Refer to the description of RTS.
Light Weight Access Point Protocol ( LWAPP )
This is a generic protocol that defines the
communication between the Access Points and the
Central Controller.
MAC Service Data Units ( MSDU )
The MSDU is that unit of data received from
the logical link control ( LLC ) sub-layer which lies
above the medium access control ( MAC ) sub-layer in a
protocol stack.
Message Integrity Code ( MIC )
A value generated by a symmetric key cryptographic
function. If the input data are changed, a new value
cannot be correctly computed without knowledge of the
symmetric key. Thus, the secret key protects the input
data from undetectable alteration.
Mobile Node ( MN )
A roaming 802.11 wireless device in a wireless
network associated with an access point. Mobile Node,
Mobile Station(Ms) and client are used
interchangeably.
Request To Send ( RTS )
A client wishing to send data initiates the process by
sending a Request To Send (RTS) frame. The destination
client replies with a Clear To Send (CTS) frame.
Wireless local-area network ( WLAN )
A local-area network that uses high-frequency radio
waves rather than wires to communicate between nodes.
Service Set Identifier (SSID)
A service set identifier is a name that identifies a
particular 802.11 wireless LAN. A client device
receives broadcast messages from all access points
within range advertising their SSIDs. The client
device can then either manually or automatically
based on configuration select the network with which
to associate. The SSID can be up to 32 characters long.
Hybrid Remote Edge Access Point (HREAP)
HREAP is a wireless solution for branch office and
remote office deployments. It enables customers to
configure and control access points in a branch or
remote office from the corporate office through a
wide area network (WAN) link without deploying a
controller in each office. HREAP is also known as
flexconnect.
Workgroup Bridge ( WGB )
A WGB can provide a wireless infrastructure connection
for a Ethernet-enabled devices. Devices that do not
have a wireless client adapter in order to connect to
the wireless network can be connected to a WGB through
Ethernet port.
KTS (Key Telephone System)
Key Telephone System is an alternative to a private
branch exchange (PBX) phone system. A KTS is equipped
with several buttons that allow a caller to directly
select outgoing lines or incoming calls, and use
intercom and conference facilities.
REFERENCE
[1] Wireless LAN Medium Access Control ( MAC ) and
Physical Layer ( PHY ) Specifications
[2] Draft-obara-capwap-lwapp-00.txt, IETF Light
Weight Access Point Protocol MODULE-IDENTITY .1.3.6.1.4.1.9.9.599 |
ciscoLwappDot11ClientMIBNotifs OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.599.0 |
ciscoLwappDot11ClientKeyDecryptErrorThis notification is generated when a decrypt error occurs.
The WEP WPA or WPA2 Key configured at the station may be
wrong.
cldcAssociationMode represents the association mode for
which the key decrypt error occurred.
cldcApMacAddress represents the MacAddress of the AP to
which the client is associated.
cldcIfType represents the wireless interface type of the
client.
cLApName represents the name of the AP to which the client
is associated. NOTIFICATION-TYPE .1.3.6.1.4.1.9.9.599.0.1 |
ciscoLwappDot11ClientAssocNacAlertThis notification is generated when the client on NAC
enabled SSIDs complete layer2 authentication . This is
to inform about client's presence to the NAC appliance.
cldcClientWlanProfileName represents the profile name of the
WLAN, this 802.11 wireless client is connected to.
cldcClientIPAddress represents the unique ipaddress of the
client.
cldcApMacAddress represents the MacAddress of the AP to
which the client is associated.
cldcClientQuarantineVLAN represents the quarantine VLAN for
the client.
cldcClientAccessVLAN represents the access VLAN for the
client. NOTIFICATION-TYPE .1.3.6.1.4.1.9.9.599.0.2 |
ciscoLwappDot11ClientDisassocNacAlertThis notification is generated when the controller removes
the client entry on NAC enabled SSIDs.
cldcClientWlanProfileName represents the profile name of the
WLAN, this 802.11 wireless client is connected to.
cldcClientIPAddress represents the unique ipaddress of the
client.
cldcApMacAddress represents the MacAddress of the AP to which
the client is associated.
cldcClientQuarantineVLAN represents the quarantine VLAN for
the client.
cldcClientAccessVLAN represents the access VLAN for the
client.
This is issued on NAC enabled ssids, whenever WLC removes
client's entry. NOTIFICATION-TYPE .1.3.6.1.4.1.9.9.599.0.3 |
ciscoLwappDot11ClientMovedToRunStateThis notification is generated when the client completes
the PEM state and moves to the RUN state.
cldcClientUsername represents the username used by the
client.
cldcClientIPAddress represents the unique ipaddress of the
client.
cldcClientSSID represents the SSID of the WLAN to which the
client is associated.
cldcApMacAddress represents the MacAddress of the AP to
which the client is associated.
cLApDot11IfSlotId represents the slotId of the AP to which
the client is associated.
cLApName represents the name of the AP to which the client
is associated. NOTIFICATION-TYPE .1.3.6.1.4.1.9.9.599.0.4 |
ciscoLwappDot11ClientStaticIpFailTrapThis is issued whenever the subnet defined for the
static IP of a client is not found. NOTIFICATION-TYPE .1.3.6.1.4.1.9.9.599.0.5 |
ciscoLwappDot11ClientDisassocDataStatsTrapThe disassociate notification shall be sent when the Station
sends a Disassociation frame. The value of the notification
shall include the MAC address of the MAC to which the
Disassociation frame was sent and the reason for the
disassociation NOTIFICATION-TYPE .1.3.6.1.4.1.9.9.599.0.6 |
ciscoLwappDot11ClientAssocDataStatsTrapThe associate notification shall be sent when the Station
sends a association frame. NOTIFICATION-TYPE .1.3.6.1.4.1.9.9.599.0.7 |
ciscoLwappDot11ClientSessionTrapIssued when the client completes the PEM state and moves
to the RUN state. NOTIFICATION-TYPE .1.3.6.1.4.1.9.9.599.0.8 |
ciscoLwappDot11ClientAssocTrapThe notification shall be sent when the Station
associats to controller. NOTIFICATION-TYPE .1.3.6.1.4.1.9.9.599.0.9 |
ciscoLwappDot11ClientDeAuthenticatedTrapThe notification shall be sent when the Station
gets de-authenticated. NOTIFICATION-TYPE .1.3.6.1.4.1.9.9.599.0.10 |
ciscoLwappDot11ClientMovedToRunStateNewTrapThe notification shall be sent when the Station
moves to run or authenticated state. NOTIFICATION-TYPE .1.3.6.1.4.1.9.9.599.0.11 |
ciscoLwappDot11ClientMobilityTrapThe notification shall be sent when the Station
gets roamed. NOTIFICATION-TYPE .1.3.6.1.4.1.9.9.599.0.12 |
ciscoLwappDot11ClientMIBObjects OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.599.1 |
cldcConfigObjects OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.599.1.1 |
cldcKeyDecryptErrorEnabledThis object specifies the status of generation of
ciscoLwappDot11ClientKeyDecryptError notification.
A value of 'true' specifies that the agent generates
ciscoLwappDot11ClientKeyDecryptError notification.
A value of 'false' specifies that the agent doesn't
generate ciscoLwappDot11ClientKeyDecryptError notification.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.599.1.1.1 |
cldcAssocNacAlertEnabledThis object specifies the status of generation of
ciscoLwappDot11ClientAssocNacAlert notification.
A value of 'true' specifies that the agent generates
ciscoLwappDot11ClientAssocNacAlert notification.
A value of 'false' specifies that the agent doesn't
generate ciscoLwappDot11ClientAssocNacAlert notification.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.599.1.1.2 |
cldcDisassocNacAlertEnabledThis object specifies the control of generation of
ciscoLwappDot11ClientDisassocNacAlert notification.
A value of 'true' specifies that the agent generates
ciscoLwappDot11ClientDisassocNacAlert notification.
A value of 'false' specifies that the agent doesn't
generate ciscoLwappDot11ClientDisassocNacAlert
notification.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.599.1.1.3 |
cldcMovedToRunStateEnabledThis object specifies the control of generation of
ciscoLwappDot11ClientMovedToRunState notification.
A value of 'true' specifies that the agent generates
ciscoLwappDot11ClientMovedToRunState notification.
A value of 'false' specifies that the agent doesn't
generate ciscoLwappDot11ClientMovedToRunState
notification.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.599.1.1.4 |
ciscoLwappDot11ClientStaticIpFailTrapEnabledThe object specifies the control of generation of
ciscoLwappDot11ClientStaticIpFailTrap notification.
A value of 'true' specifies that the agent generates
ciscoLwappDot11ClientStaticIpFailTrap notification.
A value of 'false' specifies that the agent doesn't
generate ciscoLwappDot11ClientStaticIpFailTrap
notification.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.599.1.1.5 |
cldcNotifObjects OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.599.1.2 |
cldcClientRSSIThis object represents the average RSSI for the mobile
station.ro Integer32 .1.3.6.1.4.1.9.9.599.1.2.1 |
cldcClientSNRThis object represents the average SNR for the
mobile station.ro Integer32 .1.3.6.1.4.1.9.9.599.1.2.2 |
cldcDOT11ClientReasonCodeThis object represents the reason code for failure of
client association.
A value of 'unspecified' represents that the reason for failure is
not specified.
A value 'previousAuthNotValid' represents that the reason for
failure is previous authentication was not valid.
A value of 'deauthenticationLeaving' represents that the reason for
failure is leaving due to deauthentication.
A value of 'disassociationDueToInactivity' represents that the
reason for failure is disassociation due to inactivity.
A value of 'disassociationAPBusy' represents that the reason for
failure is disassociation since AP was busy.
A value of 'class2FrameFromNonAuthStation' represents that the
reason for failure is class 2 frame from non authenticated
station.
A value of 'class2FrameFromNonAssStation' represents that the reason
for failure is class 2 frame from non associated station.
A value of 'disassociationStaHasLeft' represents that the reason for
failure is station has left due to disassociation.
A value of 'staReqAssociationWithoutAuth' represents that the reason
for failure is station send association request without
authentication.
A value of 'invalidInformationElement' represents that the reason
for failure is invalid information element.
A value of 'groupCipherInvalid' represents that the reason for
failure is invalid group Cipher.
A value of 'unicastCipherInvalid' represents that the reason for
failure is invalid unicast cipher.
A value of 'akmpInvalid' represents that the reason for failure is
invalid key management protocol.
A value of 'unsupportedRsnVersion' represents that the reason for
failure is unsupported RSN version.
A value of invalidRsnIeCapabilities' represents that the reason for
failure is invalid RSN IE capabilities.
A value of 'cipherSuiteRejected' represents that the reason for
failure is cipher suite not valid.
A value of 'missingReasonCode' represents that the reason for
failure is reason code is missing.
A value of 'maxAssociatedClientsReached' represents that the reason
for failure is maximum allowed associated client number has
reached.
A value of 'maxAssociatedClientsReachedOnRadio' represents that the
reason for failure is maximum allowed associated client number
has reached on radio.
A value of 'maxAssociatedClientsReachedOnWlan' represents that the
reason for failure is maximum allowed associated client
number has reached on wlan.
A value of 'unSpecifiedQosFailure' represents that the reason for
failure is QoS not supported.
A value of 'qosPolicyMismatch' represents that the reason for
failure is mismatch on QOS policy.
A value of 'inSufficientBandwidth' represents that the reason for
failure is insufficient bandwidth.
A value of 'inValidQosParams' represents that the reason for failure
is invalid QOS parameters.ro Enumeration .1.3.6.1.4.1.9.9.599.1.2.3 |
cldcDOT11ClientTxDataPacketsThis object represents the number of data packets sent
by this mobile stationro Counter32 .1.3.6.1.4.1.9.9.599.1.2.4 |
cldcDOT11ClientTxDataBytesThis object represents the number of data bytes sent
by this mobile stationro Counter32 .1.3.6.1.4.1.9.9.599.1.2.5 |
cldcDOT11ClientRxDataPacketsThis object represents the number of data packets sent
for this mobile stationro Counter32 .1.3.6.1.4.1.9.9.599.1.2.6 |
cldcDOT11ClientRxDataBytesThis object represents the number of data bytes sent
for this mobile stationro Counter32 .1.3.6.1.4.1.9.9.599.1.2.7 |
cldcClientVlanIdThis object represents VLAN ID of the interface to which
the client is associated.ro Integer32 .1.3.6.1.4.1.9.9.599.1.2.8 |
cldcClientPolicyTypeThis object represents security policy type on which
the mobile station is associated.
A value of 'dot1x' represents the policy type as dot1x.
A value of 'wpa1' represents the policy type as WPA version 1.
A value of 'wpa2' represents the policy type as WPA version 2.
A value of 'wpa2vff' represents the policy type as WPA2VFF.
A value of 'notavailable' represents the policy type is not
available.
A value of 'unknown' represents the policy type is not known.
A value of 'wapi' represents the policy type as WAPI.ro Enumeration .1.3.6.1.4.1.9.9.599.1.2.9 |
cldcClientEapTypeThis object represents EAP policy type used by
the mobile station during association.
A value of 'eapTls' represents the EAP policy type as EAP-TLS.
A value of 'ttls' represents the EAP policy type as TTLS.
A value of 'peap' represents the EAP policy type as PEAP.
A value of 'leap' represents the EAP policy type as LEAP.
A value of 'speke' represents the EAP policy type as EAP-SPEKE.
A value of 'eapFast' represents the EAP policy type as
EAP-FAST.
A value of 'notavailable' represents the EAP policy type
is not available
A value of 'unknown' represents the EAP policy type is
not known.ro Enumeration .1.3.6.1.4.1.9.9.599.1.2.10 |
cldcClientAIDThis object represents the AID allocated for the mobile
stationro Unsigned32 .1.3.6.1.4.1.9.9.599.1.2.11 |
cldcClientAuthenticationAlgorithmThis object represents the authentication algorithm
of mobile station used for authentication.
A value of 'openSystem' represents that the client used
open system algorithm to get authenticated.
A value of 'sharedKey' represents that the client used
shared key algorithm to get authenticated.
A value of 'unknown' represents that the algorithm used for
authentication is not known.
A value of 'openAndEap' represents that the client used
open system and EAP algorithm to get authenticated.ro Enumeration .1.3.6.1.4.1.9.9.599.1.2.12 |
cldcClientWepStateThis object represents the WEP state of the mobile station.
A value of 'enable' represents WEP state is enabled.
A value of 'disable' represents WEP state is disbaled.ro Enumeration .1.3.6.1.4.1.9.9.599.1.2.13 |
cldcClientEncryptionCipherThis object represents encryption cipher selected for
encryption of mobile station traffic.
A value of 'ccmpAes' represents the encryption used is
CCMP AES.
A value of 'tkipMic' represents the encryption used is
TKIP-MIC.
A value of 'wep40' represents the encryption used is
WEP40.
A value of 'wep104' represents the encryption used is
WEP104.
A value of 'wep128' represents the encryption used is
WEP128.
A value of 'none' represents the no encryption used.
A value of 'notavailable' represents the encryption used
is not available.
A value of 'unknown' represents the encryption is used is
not known.
A value of 'wapiSMS4' represents the encryption is used is
WAPI-SMS4.ro Enumeration .1.3.6.1.4.1.9.9.599.1.2.14 |
cldcClientPortNumberThis object represents the port number of this
airespace switch on which the traffic of the
mobile station is coming through.ro Unsigned32 .1.3.6.1.4.1.9.9.599.1.2.15 |
cldcClientAnchorAddressTypeThis object represents mobility anchor address type.ro InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.9.9.599.1.2.16 |
cldcClientAnchorAddressThis object represent anchor IP address.
If the mobility status of the mobile station is
anchor then it will have peer Ip address and will
have anchor IP if the role is foreignro InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.9.9.599.1.2.17 |
cldcClientEssIndexThis object represents the ESS index of the WLAN(SSID)
that is being used by mobile station to connect to APro Unsigned32 .1.3.6.1.4.1.9.9.599.1.2.18 |
cldcClientCcxVersionThis object represents the Cisco Compatible Extensions (CCX)
version the client is using for communication with the AP.
A value of 'notSupported' represents CCX version is not
supported.
A value of 'ccxv1' represents that client used CCX version 1
for communication.
A value of 'ccxv2' represents that client used CCX version 2
for communication.
A value of 'ccxv3' represents that client used CCX version 3
for communication.
A value of 'ccxv4' represents that client used CCX version 4
for communication.
A value of 'ccxv5' represents that client used CCX version 5
for communication.
A value of 'ccxv6' represents that client used CCX version 6
for communication.ro Enumeration .1.3.6.1.4.1.9.9.599.1.2.19 |
cldcClientE2eVersionThis object represents the End-2-End Version the client is
using for communication with the AP.
A value of 'notSupported' represents end-2-end version
is not supported.
A value of 'e2ev1' represents end-2-end version used by
mobile station is 1.
A value of 'e2ev2' represents end-2-end version used by
mobile station is 2.ro Enumeration .1.3.6.1.4.1.9.9.599.1.2.20 |
cldcClientInterfaceThis object represents the name of the interface of
the mobile client on which traffic sent to the switch.ro SnmpAdminString .1.3.6.1.4.1.9.9.599.1.2.21 |
cldcClientMobilityStatusThis object represents the mobility role of the
mobile station.
A value of 'unassociated' represents mobility role
is not associated.
A value of 'local' represents mobility role
is local.
A value of 'anchor' represents mobility role
is anchor.
A value of 'foreign' represents mobility role
is foreign.
A value of 'handoff' represents mobility role
is handoff.
A value of 'unknown' represents mobility role
is not known.
A value of 'exportanchor' represents mobility role
is exportanchor.
A value of 'exportforeign' represents mobility role
is exportforeign.ro Enumeration .1.3.6.1.4.1.9.9.599.1.2.22 |
cldcClientStatusCodeThis object represents status code of the mobile stationro INTEGER .1.3.6.1.4.1.9.9.599.1.2.23 |
cldcClientDeleteActionThis object represents the action to deauthenticate
the mobile station.
A value of 'default' represents the state as default.
A value of 'delete' represents the state as delete.ro Enumeration .1.3.6.1.4.1.9.9.599.1.2.24 |
cldcClientSecurityPolicyStatusThis object represents the security policy state of
the mobile station.
A value of 'completed' represents the mobile station
has completed the security policy checks.
A value of 'notcompleted' represents policy checks are yet
to be completed for the mobile station.ro Enumeration .1.3.6.1.4.1.9.9.599.1.2.25 |
cldcClientTrapEventTimeThis object represents the trap event time of
the client.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.9.9.599.1.2.26 |
cldcClientPolicyManagerStateThis object represents the current policy enforcement
manager state of the client in controller.ro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.9.9.599.1.2.27 |
cldcClientAssocTimeThis object represents the time at which client associatedro TimeStamp (SNMPv2-TC) .1.3.6.1.4.1.9.9.599.1.2.28 |
cldcClientPmipDataValidThis object represents whether client has valid PMIP data.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.599.1.2.29 |
cldcClientMobilityExtDataValidThis object represents new mobility status.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.599.1.2.30 |
cldcClientPolicyErrorsThis object represents the number of policy
errors for mobile stationro Counter64 .1.3.6.1.4.1.9.9.599.1.2.31 |
cldcClientSessionIdThis object represents the session
to which the client is associated.ro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.9.9.599.1.2.32 |
cldcClientPmipNaiThis object represents the name of the
profile, the client is associated to.ro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.9.9.599.1.2.33 |
cldcClientPmipStateThis object indicates the state of the PMIP client:
null: binding doesn't exist
init: binding created, Retx timer running for PBU, binding not
yet accepted from LMA, Tunnel/route is not yet setup
active: binding accepted by LMA, refresh timer running,
Tunnel/route setup complete.
refreshPending: Refresh timer expired and Retx timer running.
PBU refresh sent, PBA not yet received from LMA,
(Tunnel/route is already setup).
disconnectingSt: Dereg reply is expected. Retx timer is
running, tunnel/route is still setup.ro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.9.9.599.1.2.34 |
cldcClientPmipInterfaceThis object indicates the interface to which the
client is associated.ro SnmpAdminString .1.3.6.1.4.1.9.9.599.1.2.35 |
cldcClientPmipHomeAddrTypeThis object indicates the type of the Client's Home
address made available through cldcClientPmipHomeAddress.ro InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.9.9.599.1.2.36 |
cldcClientPmipHomeAddrThis object indicates the Home Address of the client.ro InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.9.9.599.1.2.37 |
cldcClientPmipAttThis object indicates the access technology type by which
the client is currently attached.
A value of 'reserved' indicates this value is reserved for
future use.
A value of 'logicalNetworkInterface' indicates that the
client used logical network interface to connect to network.
A value of 'pointToPointInterface' indicates that the
client used point to point interface to connect to network.
A value of 'ethernet' indicates that the client used
ethernet to connect to network.
A value of 'wirelessLan' indicates that the
client used wireless LAN to connect to network.
A value of 'wimax' indicates that the
client used WiMAX technology to connect to network.
A value of 'threeGPPGERAN' indicates that the
client used threeGPPGERAN technology to connect to network.
A value of 'threeGPPUTRAN' indicates that the
client used threeGPPUTRAN technology to connect to network.
A value of 'threeGPPETRAN' indicates that the
client used threeGPPETRAN technology to connect to network.
A value of 'threeGPP2eHRPD' indicates that the
client used threeGPP2eHRPD technology to connect to network.
A value of 'threeGPP2HRPD' indicates that the
client used threeGPP2HRPD technology to connect to network.
A value of 'threeGPP21xRTT' indicates that the
client used threeGPP21xRTT technology to connect to network.
A value of 'threeGPP2UMB' indicates that the
client used threeGPP2UMB technology to connect to network.ro Enumeration .1.3.6.1.4.1.9.9.599.1.2.38 |
cldcClientPmipLocalLinkIdThis object indicates the local link identifier of
the client.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.9.9.599.1.2.39 |
cldcClientPmipLmaNameThis object indicates the LMA to which the client is
connected.ro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.9.9.599.1.2.40 |
cldcClientPmipLifeTimeThis object indicates the duration of the PMIP client
association.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.9.9.599.1.2.41 |
cldcClientPmipDomainNameThis object indicates the domain to which the PMIP
client is associated.ro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.9.9.599.1.2.42 |
cldcClientPmipUpKeyThis object indicates the upstream key of the PMIP client.ro Unsigned32 .1.3.6.1.4.1.9.9.599.1.2.43 |
cldcClientPmipDownKeyThis object indicates the downstream key of the PMIP client.ro Unsigned32 .1.3.6.1.4.1.9.9.599.1.2.44 |
cldcStatusObjects OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.599.1.3 |
cldcClientTableThis table represents the 802.11 wireless clients
that are associated with the APs that have joined
this controller.
An entry is created automatically by the controller
when the client gets associated to the AP. An existing
entry gets deleted when the association gets dropped.
Each client added to this table is uniquely identified
by the client's MAC address. SEQUENCE OF CldcClientEntry .1.3.6.1.4.1.9.9.599.1.3.1 |
cldcClientEntryEach entry represents a conceptual row in this
table and provides the information about the
clients associated to the APs that have joined
the controller. An entry is identified the client's
MAC address. CldcClientEntry .1.3.6.1.4.1.9.9.599.1.3.1.1 |
cldcClientMacAddressThis object represents the MAC address of the
client for this entry and uniquely identifies
this entry. MacAddress (SNMPv2-TC) .1.3.6.1.4.1.9.9.599.1.3.1.1.1 |
cldcClientStatusThis object represents the current status of
the client.ro CLDot11ClientStatus (CISCO-LWAPP-TC-MIB) .1.3.6.1.4.1.9.9.599.1.3.1.1.2 |
cldcClientWlanProfileNameThis object represents the WLAN profile name
this 802.11 wireless client is connected to.ro SnmpAdminString .1.3.6.1.4.1.9.9.599.1.3.1.1.3 |
cldcClientWgbStatusThis object represents the work group bridging
status of a DOT11 client.
A value of 'regClient' represents that the client is
a wireless client
A value of 'wgbClient' represents that the client is
connected via a WGB
A value of 'wgb' represents that the client is the
WGB itself.ro Enumeration .1.3.6.1.4.1.9.9.599.1.3.1.1.4 |
cldcClientWgbMacAddressThis object represents the MAC address of the
WGB this 802.11 wireless client to which it is
connected. This returns a non-zero value when
the cldcClientWgbStatus is wgbClient.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.9.9.599.1.3.1.1.5 |
cldcClientProtocolThis object represents 802.11 protocol type of the
client it used to join to wireless network.
A value of 'dot11a' represents that the client is using
802.11a standard to connect to the access point (AP)
A value of 'dot11b' represents that the client is using
802.11b standard to connect to the access point (AP)
A value of 'dot11g' represents that the client is using
802.11g standard to connect to the access point (AP)
A value of 'unknown' represents that the client protocol
is unknown
A value of 'mobile' represents that the client using mobile
wireless to connect to the access point (AP).
A value of 'dot11n24' represents that the client is using
802.11n standard with 2.4 GHz frequency to connect to
the access point (AP)
A value of 'dot11n5' represents that the client is using
802.11n standard with 5 GHz frequency to connect to
the access point (AP).
A value of 'ethernet' represents that the client is using
ethernet standard to connect to the access point (AP).
A value of 'dot3' represents that the client is using
dot3 standard to connect to the access point (AP).
A value of 'dot11ac5' represents that the client is using
802.11ac standard with 5 GHz frequency to connect to
the access point (AP).ro Enumeration .1.3.6.1.4.1.9.9.599.1.3.1.1.6 |
cldcAssociationModeThis object represents the association mode used
by client for protected wireless traffic.
A value of 'unknown' represents that association mode used
by client for wilress traffic encryption is not known.
A value of 'wep' represents that association mode used
by client for wilress traffic encryption is WEP.
A value of 'wpa' represents that association mode used
by client for wilress traffic encryption is WPA.
A value of 'wpa2' represents that association mode used
by client for wilress traffic encryption is WPA2.ro Enumeration .1.3.6.1.4.1.9.9.599.1.3.1.1.7 |
cldcApMacAddressThis object represents the radio MAC address
of a LWAPP AP.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.9.9.599.1.3.1.1.8 |
cldcIfTypeThis object represents the wireless interface type.ro CLApIfType (CISCO-LWAPP-TC-MIB) .1.3.6.1.4.1.9.9.599.1.3.1.1.9 |
cldcClientIPAddressThis object represents client's IP address.
This is learnt from the client details when the client
associates with the access point.ro IpAddress .1.3.6.1.4.1.9.9.599.1.3.1.1.10 |
cldcClientNacStateThis object specifies that client's network admission
control state.
A value of 'quarantine' specifies that client goes through
posture analysis and the client traffic is sent by
controller in quarantine vlan.
A value of 'access' specifies that client traffic is sent
by controller in access vlan. The client should have
completed posture analysis.
Posture Analysis is a state change where the client
applies the configured policies to validate access
to the network.rw Enumeration .1.3.6.1.4.1.9.9.599.1.3.1.1.11 |
cldcClientQuarantineVLANThis object indicates the quarantine VLAN for client. The
quarantine VLAN only allows limited access to the network.ro VlanId (Q-BRIDGE-MIB) .1.3.6.1.4.1.9.9.599.1.3.1.1.12 |
cldcClientAccessVLANThis object indicates the access VLAN for client.
The access VLAN allows unlimited access to the network.ro VlanId (Q-BRIDGE-MIB) .1.3.6.1.4.1.9.9.599.1.3.1.1.13 |
cldcClientLoginTimeThis object indicates the value of sysUpTime when the
client logged in.ro TimeStamp (SNMPv2-TC) .1.3.6.1.4.1.9.9.599.1.3.1.1.14 |
cldcClientUpTimeThis object indicates the duration for which the client
has been associated with this device.ro TimeInterval UNITS "Seconds" .1.3.6.1.4.1.9.9.599.1.3.1.1.15 |
cldcClientPowerSaveModeThis object indicates the power management mode of
the client.ro CLClientPowerSaveMode (CISCO-LWAPP-TC-MIB) .1.3.6.1.4.1.9.9.599.1.3.1.1.16 |
cldcClientCurrentTxRateSetThis object indicates the current data rate at which the
client transmits and receives data. The data rate field is
a 16-bit unsigned value expressing the data rate of the
packets received by the client.ro OCTET STRING .1.3.6.1.4.1.9.9.599.1.3.1.1.17 |
cldcClientDataRateSetThis object indicates the set of data rates at which the
client may transmit data. Each client can support up to
126 rates. Each octet contains an integer value
representing one of these 126 rates ranging from 1 Mb/s
to 63.5 Mb/s. One of the supported rates will be chosen
by the access point for transmission with the client.ro OCTET STRING .1.3.6.1.4.1.9.9.599.1.3.1.1.18 |
cldcClientHreapApAuthThis object indicates whether the client is locally
authenticated or authenticated by the controller.
Local authentication is done only if the Access Point
connected to the client is of flexconnect mode.
A value of 'true' indicates that the client is
authenticated by the AP..
A value of 'false' indicates that the client is
authenticated by the controller.
A value of 'notApplicable' indicates that client is not
connected to a flexconect AP.ro Enumeration .1.3.6.1.4.1.9.9.599.1.3.1.1.19 |
cldcClient80211uCapableThis object indicates whether the client supports
802.11u feature.
The 802.11u standard allows devices such as laptop
computers or cellular phones to join a wireless LAN
widely used in the home, office and some commercial
establishments.
A value of 'true' indicates that the client supports the
802.11u feature.
A value of 'false' indicates that the client does not
support the 802.11u feature.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.599.1.3.1.1.20 |
cldcClientPostureStateThis object indicates the posture state of the client.
Posture Analysis is a state change where the client applies
the configured policies to validate access to the network.
A value of 'true' indicates that the client supports the
posture feature.
A value of 'false' indicates that the client does not support
the posture feature.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.599.1.3.1.1.21 |
cldcClientAclNameThis object indicates the ACL Name for the client.
This ACL will be used to allow or block client traffic
based on the list of rules attached to the ACL.ro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.9.9.599.1.3.1.1.22 |
cldcClientAclAppliedThis object indicates the ACL applied status for the
client.
A value of 'true' indicates that the ACL is applied.
A value of 'false' indicates that the ACL is not applied.
A value of 'notAvailable' indicates that applied status
is not availablero Enumeration .1.3.6.1.4.1.9.9.599.1.3.1.1.23 |
cldcClientRedirectUrlThis object indicates the AAA override redirect URL for a
client with cldcClientPostureState enabled.
The object has a valid value when the WLAN, with which the
client has associated requires conditional or splash-page
or webauth web redirection.
This object is otherwise not applicable,
and contains a zero-length string.ro CiscoURLStringOrEmpty (CISCO-TC) .1.3.6.1.4.1.9.9.599.1.3.1.1.24 |
cldcClientAaaOverrideAclNameThis object indicates the AAA Override ACL Name for the
client if cldcClientPostureState is enabled on the wlan.ro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.9.9.599.1.3.1.1.25 |
cldcClientAaaOverrideAclAppliedThis object indicates the AAA Override ACL applied status for
the client if cldcClientPostureState is enabled on the wlan.
A value of 'true' indicates that the ACL is applied.
A value of 'false' indicates that the ACL is not applied.
A value of 'notAvailable' indicates that applied status is
not availablero Enumeration .1.3.6.1.4.1.9.9.599.1.3.1.1.26 |
cldcClientUsernameThis object represents the username used by the client.ro SnmpAdminString .1.3.6.1.4.1.9.9.599.1.3.1.1.27 |
cldcClientSSIDThis object represents the SSID of the WLAN to which the
client is associated.ro SnmpAdminString .1.3.6.1.4.1.9.9.599.1.3.1.1.28 |
cldcClientSecurityTagIdThis object represents the security group tag of the client.ro Unsigned32 .1.3.6.1.4.1.9.9.599.1.3.1.1.29 |
cldcClientTypeKTSThis object indicates whether the client is NEC KTS (National
Electrical Code Key Telephone servie) client or not.
A value of 'true' indicates that the client follows NEC
KTS SIP protocol.
A value of 'false' indicates that the client does not follow
NEC KTS SIP protocol.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.599.1.3.1.1.30 |
cldcClientIpv6AclNameThis object indicates the ACL name for the IPv6 client.
An empty string denotes no ACL has been applied.ro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.9.9.599.1.3.1.1.31 |
cldcClientIpv6AclAppliedThis object indicates the ACL applied status for the IPv6
client.
A value of 'true' indicates that the ACL is applied.
A value of 'false' indicates that the ACL is not applied.
A value of 'notAvailable' indicates that applied status is
not avaliablero Enumeration .1.3.6.1.4.1.9.9.599.1.3.1.1.32 |
cldcClientDataSwitchingThis object indicates whether client is switching data
locally or centrally. This object is valid for flexconnect
APs.
A value of 'unknown' indicates that client data switching is
not known.
A value of 'central' indicates that client data is tunneled
to WLC using CAPWAP.
A value of 'local' indicates that client data is bridged
locally by AP.ro Enumeration .1.3.6.1.4.1.9.9.599.1.3.1.1.33 |
cldcClientAuthenticationThis object indicates whether client is authentiated
locally or centrally. This object is valid for flexconnect
APs.
A value of 'unknown' indicates that client authentication is
not known.
A value of 'central' indicates that client authenticatation is
at WLC and AP tunnels client management traffic to WLC
via CAPWAP.
A value of 'local' indicates that client is authenticated
locally by AP.ro Enumeration .1.3.6.1.4.1.9.9.599.1.3.1.1.34 |
cldcClientChannelThis object indicates the access point's channel
to which the client is associated.ro Unsigned32 .1.3.6.1.4.1.9.9.599.1.3.1.1.35 |
cldcClientAuthModeThis object represents the authentication mode of client.
A value of 'none' represents that client used
open authentication to join to network.
A value of 'psk' represents that client used
PSK based authentication to join to network.
A value of 'radius' represents that client gets
authenticated with the help of radius.
A value of 'cckm' represents that client used
CCKM based authentication to join to network.
A value of 'wapipsk' represents that client used
WAPI PSK authentication to join to network.
A value of 'wapicert' represents that client used
WPA/WPA2 DOT1X authentication to join to network.
A value of 'ftDot1x' represents that client used
802.11r DOT1X authentication to join to network.
A value of 'ftpsk' represents that client used
802.11r PSK authentication to join to network.
A value of 'pmfDot1x' represents that client used
PMF DOT1X authentication to join to network.
A value of 'pmfpsk' represents that client used
PMF PSK authentication to join to network.ro Enumeration .1.3.6.1.4.1.9.9.599.1.3.1.1.36 |
cldcClientReasonCodeThis object represents the reason for disassociation
of client.
A value of 'unspecified' represents that client disassociated
with reaon unspecified.
A value of 'previousAuthNotValid' represents that client
disassociated with reason previous authentication
was not valid.
A value of 'deauthenticationLeaving' represents that client
disassociated with reason client leaving due to
deauthentication.
A value of 'disassociationDueToInactivity' represents that client
disassociated with reason client disassociation due to
inactivity.
A value of 'disassociationAPBusy' represents that client
disassociated with reason client disassociation since AP
was busy.
A value of 'class2FrameFromNonAuthStation' represents that client
disassociated with reason class 2 frame
from non authenticated station.
A value of 'class2FrameFromNonAssStation' represents that client
disassociated with reason class 2 frame from non
associated station.
A value of 'disassociationStaHasLeft' represents that client
disassociated with reason station has left BSS due
to disassociation.
A value of 'staReqAssociationWithoutAuth' represents that client
disassociated with reason station send association request
without authentication.
A value of 'invalidInformationElement' represents that client
disassociated with reason stations send invalid information
element in the management frame.
A value of 'groupCipherInvalid' represents that client
disassociated with reason invalid group cipher.
A value of 'unicastCipherInvalid' represents that client
disassociated with reason invalid unicast cipher.
A value of 'akmpInvalid' represents that client
disassociated with reason invalid key management protocol.
A value of 'unsupportedRsnVersion' represents that client
disassociated with reason unsupported RSN version.
A value of 'invalidRsnIeCapabilities' represents that client
disassociated with reason invalid RSN IE capabilities
in the (re-)association request.
A value of 'cipherSuiteRejected' represents that client
disassociated with reason cipher suite rejected.
A value of 'missingReasonCode' represents that client
disassociated with reason reason code is missing.
A value of 'maxAssociatedClientsReached' represents that
client disassociated with reason maximum allowed
associated client number has reached.
A value of 'maxAssociatedClientsReachedOnRadio' represents that
client disassociated with reason maximum allowed
associated client number has reached on radio.
A value of 'maxAssociatedClientsReachedOnWlan' represents that
client disassociated with reason maximum allowed
associated client number has reached on wlan.
A value of 'unSpecifiedQosFailure' represents that client
disassociated with reason unsupported QOS failure.
A value of 'qosPolicyMismatch' represents that client
disassociated with reason mismatch on QOS policy.
A value of 'inSufficientBandwidth' represents that client
disassociated with reason insufficient bandwidth to
accommodate this station.
A value of 'inValidQosParams' represents that client
disassociated with reason invalid QOS parameters.ro Enumeration .1.3.6.1.4.1.9.9.599.1.3.1.1.37 |
cldcClientSessionIDThis object indicates the session
to which the client is associated.ro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.9.9.599.1.3.1.1.38 |
cldcClientApRoamMacAddressThis object indicates the MAC address of the
AP to which the client has roamed.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.9.9.599.1.3.1.1.39 |
cldcClientMdnsProfileThis object indicates the mDNS profile name
mapped to 802.11 wireless client. It could
be mapped to the WLAN to which the client is
connected to, or the interface/interface groups
mapped to the WLAN.ro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.9.9.599.1.3.1.1.40 |
cldcClientMdnsAdvCountThis object indicates the number of mDNS
advertisements received on the client.ro Unsigned32 .1.3.6.1.4.1.9.9.599.1.3.1.1.41 |
cldcClientPolicyNameThis object indicates the local classification
policy applied on the client.ro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.9.9.599.1.3.1.1.42 |
cldcClientAAARoleThis object indicates the role string of the client
that is used as match criterion for local policy
profiling. This value is provided by radius during
authentication.ro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.9.9.599.1.3.1.1.43 |
cldcClientDeviceTypeThis object indicates the device type of the client.
This is identified once the profiling operation is
completed.ro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.9.9.599.1.3.1.1.44 |
cldcUserAuthTypeThis object indicates the authentication aype of user.
A value of 'open' indicates that the user authenticated using
open security.
A value of 'wepPsk' indicates that the user authenticated using
WEP PSK security.
A value of 'portal' indicates that the user authenticated using
WEB layer3 portal security.
A value of 'simPeap' indicates that the user authenticated using
EAP SIM and PEAP security.
A value of 'other' indicates that the user authenticated using
security method not listed above.ro Enumeration .1.3.6.1.4.1.9.9.599.1.3.1.1.45 |
cldcClientTunnelTypeThis object indicates the tunnel type used to send
client traffic.
A value of 'simple' indicates no tunnel is used to send
client traffic towards DS.
A value of 'pmipv6' indicates that PMIPv6 tunnel is used
to send client traffic towards DS.
A value of 'gtpv2' indicates that GTPv2 tunnel is used
to send client traffic towards DS.
A value of 'eogre' indicates that EOGRE tunnel is used
to send client traffic towards DS.ro Enumeration .1.3.6.1.4.1.9.9.599.1.3.1.1.46 |
cldcClientMaxDataRateThis object indicates the max data rate (Mbps)
with which the client can operate.ro Unsigned32 .1.3.6.1.4.1.9.9.599.1.3.1.1.47 |
cldcClientHtCapableThis object indicates whether the client is HT
(high throughput) capable or not.
A value of 'true' indicates that client is HT capable.
A value of 'false' indicates that client is not HT capable.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.599.1.3.1.1.48 |
cldcClientVhtCapableThis object indicates whether the client is VHT
(very high throughput) capable or not.
A value of 'true' indicates that client is VHT capable.
A value of 'false' indicates that client is not VHT capable.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.599.1.3.1.1.49 |
cldcClientCurrentTxRateThis object represents the current data rate at which the
client transmits and receives data. This provides the data
rate value equivalent to the MCS value displayed in
cldcClientCurrentTxRateSet.ro Unsigned32 UNITS "Mbit/s" .1.3.6.1.4.1.9.9.599.1.3.1.1.50 |
cldcClientiPSKTagThis object indicates the iPSK peer group that this client is part of.
The clients with same ipsk tag can be allowed to have peer to peer traffic by
configuring the wlan p2p blocking.ro OCTET STRING .1.3.6.1.4.1.9.9.599.1.3.1.1.51 |
cldcClientByIpTableThis table represents the 802.11 wireless clients
that are associated with the APs that have joined
this controller and are indexed by
cldcClientByIpAddressType and cldcClientByIpAddress.
An entry is created automatically by the controller
when the client gets associated to the AP. An existing
entry gets deleted when the association gets dropped. SEQUENCE OF CldcClientByIpEntry .1.3.6.1.4.1.9.9.599.1.3.2 |
cldcClientByIpEntryEach entry represents a conceptual row in this
table and provides the information about the
clients associated to the APs that have joined
the controller. An entry is identified by the client's
IP address. CldcClientByIpEntry .1.3.6.1.4.1.9.9.599.1.3.2.1 |
cldcClientByIpAddressTypeThis object represents the type of the Client's
address made available through
cldcClientByIpAddress. InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.9.9.599.1.3.2.1.2 |
cldcClientByIpAddressThis object indicates the client IP address. InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.9.9.599.1.3.2.1.3 |
cldcClientByIpAddressDiscoverTypeThis object represents the discovery type of the
client's address
A value of 'invalid' indicates that the IP address
discover type is unknown.
A value of 'ndp' indicates that the client learnt
IP address by neighbor discovery protocol
A value of 'dhcp' indicates that the client learnt
IP address via DHCP.
A value of 'packet' indicates that the client learnt
IP address via data packet addressing learning.
A value of 'local' indicates that the client learnt
IP address via address applied to local interface.
A value of 'static' indicates that the client learnt
IP address via address assigned statically.ro Enumeration .1.3.6.1.4.1.9.9.599.1.3.2.1.4 |
cldcClientByIpAddressLastSeenThis object indicates the time when an address was
last seen in reachable state.ro TimeStamp (SNMPv2-TC) .1.3.6.1.4.1.9.9.599.1.3.2.1.5 |
cldcSleepingClientTableThis table represents the information about
sleeping clients SEQUENCE OF CldcSleepingClientEntry .1.3.6.1.4.1.9.9.599.1.3.3 |
cldcSleepingClientEntryAn entry containing the information about sleeping
clients. CldcSleepingClientEntry .1.3.6.1.4.1.9.9.599.1.3.3.1 |
cldcSleepingClientMacAddressThis object represents the MAC address of the
sleeping client and uniquely identifies the entry. MacAddress (SNMPv2-TC) .1.3.6.1.4.1.9.9.599.1.3.3.1.1 |
cldcSleepingClientSsidThis object represents the SSID of the WLAN to which the
sleeping client is associated.ro OCTET STRING .1.3.6.1.4.1.9.9.599.1.3.3.1.2 |
cldcSleepingClientUserNameThis object represents the username used by the sleeping
client.ro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.9.9.599.1.3.3.1.3 |
cldcSleepingClientRemainingTimeThis object indicates the remaining session time
for the sleeping client to be in associated state.ro TimeInterval UNITS "seconds" .1.3.6.1.4.1.9.9.599.1.3.3.1.4 |
cldcSleepingClientRowStatusThis object specifies the status column for this row
and used to delete specific instances of row in the table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.9.9.599.1.3.3.1.5 |
cldcStatisticObjects OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.599.1.4 |
cldcClientStatisticTableThis table represents statistics and status of the 802.11
wireless clients associated to the controller. SEQUENCE OF CldcClientStatisticEntry .1.3.6.1.4.1.9.9.599.1.4.1 |
cldcClientStatisticEntryAn entry in this table represents traffic statistics of the
associated client. CldcClientStatisticEntry .1.3.6.1.4.1.9.9.599.1.4.1.1 |
cldcClientDataRetriesThis object indicates the number of attempts made by the
client before transmitting the MSDU successfully.ro Counter64 UNITS "Retries" .1.3.6.1.4.1.9.9.599.1.4.1.1.1 |
cldcClientRtsRetriesThis object indicates the number of times the client has
attempted to send RTS packets before receiving CTS packets.ro Counter64 UNITS "Retries" .1.3.6.1.4.1.9.9.599.1.4.1.1.2 |
cldcClientDuplicatePacketsThis object indicates the number of times a duplicate
packet is received for the client.ro Counter64 UNITS "Packets" .1.3.6.1.4.1.9.9.599.1.4.1.1.3 |
cldcClientDecryptFailuresThis object indicates the number of packets received from
the client that failed to decrypt properly.ro Counter64 UNITS "Packets" .1.3.6.1.4.1.9.9.599.1.4.1.1.4 |
cldcClientMicErrorsThis object indicates the number of MIC errors
experienced by the client.ro Counter64 UNITS "Packets" .1.3.6.1.4.1.9.9.599.1.4.1.1.5 |
cldcClientMicMissingFramesThis object indicates the number of missing MIC packets
for the client.ro Counter64 UNITS "Packets" .1.3.6.1.4.1.9.9.599.1.4.1.1.6 |
cldcClientRaPacketsDroppedThis object indicates the number of RA (router
advertisements) packets dropped for this client.
It's applicable for IPv6 clients only.ro Counter64 .1.3.6.1.4.1.9.9.599.1.4.1.1.7 |
cldcClientInterimUpdatesCountThis object indicates the number of interim updates
sent for this client.ro Counter64 .1.3.6.1.4.1.9.9.599.1.4.1.1.8 |
cldcClientDataBytesReceivedThis object indicates the number of data bytes received
for this clientro Counter64 .1.3.6.1.4.1.9.9.599.1.4.1.1.9 |
cldcClientRealtimeBytesReceivedThis object indicates the number of realtime bytes
received for this mobile stationro Counter64 .1.3.6.1.4.1.9.9.599.1.4.1.1.10 |
cldcClientRxDataBytesDroppedThis object indicates the number of received data bytes
dropped for this mobile stationro Counter64 .1.3.6.1.4.1.9.9.599.1.4.1.1.11 |
cldcClientRxRealtimeBytesDroppedThis object indicates the number of received realtime bytes
dropped for this mobile stationro Counter64 .1.3.6.1.4.1.9.9.599.1.4.1.1.12 |
cldcClientDataBytesSentThis object indicates the number of data bytes sent for
this mobile stationro Counter64 .1.3.6.1.4.1.9.9.599.1.4.1.1.13 |
cldcClientRealtimeBytesSentThis object indicates the number of realtime bytes sent
for this mobile stationro Counter64 .1.3.6.1.4.1.9.9.599.1.4.1.1.14 |
cldcClientTxDataBytesDroppedThis object indicates the number of transmitted data
bytes dropped for this mobile stationro Counter64 .1.3.6.1.4.1.9.9.599.1.4.1.1.15 |
cldcClientTxRealtimeBytesDroppedThis object indicates the number of transmitted realtime
bytes dropped for this mobile stationro Counter64 .1.3.6.1.4.1.9.9.599.1.4.1.1.16 |
cldcClientDataPacketsReceivedThis object indicates the number of data packets
received for this mobile stationro Counter64 .1.3.6.1.4.1.9.9.599.1.4.1.1.17 |
cldcClientRealtimePacketsReceivedThis object indicates the number realtime packets
received for this mobile stationro Counter64 .1.3.6.1.4.1.9.9.599.1.4.1.1.18 |
cldcClientRxDataPacketsDroppedThis object indicates the number of received data packets
dropped for this mobile stationro Counter64 .1.3.6.1.4.1.9.9.599.1.4.1.1.19 |
cldcClientRxRealtimePacketsDroppedThis object indicates the number of received realtime
packets dropped for this mobile stationro Counter64 .1.3.6.1.4.1.9.9.599.1.4.1.1.20 |
cldcClientDataPacketsSentThis object indicates the number of data packets sent
for this mobile stationro Counter64 .1.3.6.1.4.1.9.9.599.1.4.1.1.21 |
cldcClientRealtimePacketsSentThis object indicates the number of realtime packets
sent for this mobile stationro Counter64 .1.3.6.1.4.1.9.9.599.1.4.1.1.22 |
cldcClientTxDataPacketsDroppedThis object indicates the number of transmitted data
packets dropped for this mobile stationro Counter64 .1.3.6.1.4.1.9.9.599.1.4.1.1.23 |
cldcClientTxRealtimePacketsDroppedThis object indicates the number of transmitted realtime
packets dropped for this mobile stationro Counter64 .1.3.6.1.4.1.9.9.599.1.4.1.1.24 |
cldcClientTxDataPacketsThis object indicates the number of data packets sent
by this mobile stationro Counter64 .1.3.6.1.4.1.9.9.599.1.4.1.1.25 |
cldcClientTxDataBytesThis object indicates the number of data bytes sent
by this mobile stationro Counter64 .1.3.6.1.4.1.9.9.599.1.4.1.1.26 |
cldcClientRxDataPacketsThis object indicates the number of data packets sent
for this mobile stationro Counter64 .1.3.6.1.4.1.9.9.599.1.4.1.1.27 |
cldcClientRxDataBytesThis object indicates the number of data bytes sent
for this mobile stationro Counter64 .1.3.6.1.4.1.9.9.599.1.4.1.1.28 |
ciscoLwappDot11ClientMIBConform OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.599.2 |
ciscoLwappDot11ClientMIBCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.599.2.1 |
ciscoLwappDot11ClientMIBGroups OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.599.2.2 |
ciscoLwappDot11CCXClientMIBConform OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.599.2.3 |
ciscoLwappDot11ClientCCXV5ReportingMIBConform OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.599.2.4 |
ciscoLwappDot11ClientCcxMIBObjects OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.599.3 |
cldcCcxObjects OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.599.3.1 |
cldccCcxVersionInfoTableThis table represents the detail of the CCX version
supported by the clients. This is used to identify
the services supported by a CCX v6 client. SEQUENCE OF CldccCcxVersionInfoEntry .1.3.6.1.4.1.9.9.599.3.1.1 |
cldccCcxVersionInfoEntryThere is an entry in the table for each entry identified
by the client mac address.
An entry is added when a CCX v6 client associates to the
controller and existing entry gets deleted when the client
disassociates from the controller. CldccCcxVersionInfoEntry .1.3.6.1.4.1.9.9.599.3.1.1.1 |
cldccCcxFoundationServiceVersionThis object indicates the CCX version supported by
the client for the foundation service.ro CcxServiceVersion (CISCO-LWAPP-TC-MIB) .1.3.6.1.4.1.9.9.599.3.1.1.1.1 |
cldccCcxLocationServiceVersionThis object indicates the CCX version supported by
the client for the location service.ro CcxServiceVersion (CISCO-LWAPP-TC-MIB) .1.3.6.1.4.1.9.9.599.3.1.1.1.2 |
cldccCcxVoiceServiceVersionThis object indicates the CCX version supported by
the client for the voice service.ro CcxServiceVersion (CISCO-LWAPP-TC-MIB) .1.3.6.1.4.1.9.9.599.3.1.1.1.3 |
cldccCcxManagementServiceVersionThis object indicates the CCX version supported by
the client for the management service.ro CcxServiceVersion (CISCO-LWAPP-TC-MIB) .1.3.6.1.4.1.9.9.599.3.1.1.1.4 |