Home/Catalog/CISCO-LWAPP-AP-MIB

CISCO-LWAPP-AP-MIB

AI MIB Summary

The CISCO-LWAPP-AP-MIB enables network management systems to monitor and configure Cisco Central Controllers managing Lightweight Access Points via the LWAPP protocol, specifically tracking AP association states, tunnel link latency, and encapsulated 802.11 traffic parameters. It provides granular visibility into the controller-to-AP relationship, including BSSID status, WIPS alerts, and DTLS security states for the centralized wireless infrastructure.

This MIB is intended to be implemented on all those devices operating as Central Controllers (CC) that terminate the Light Weight Access Point Protocol tunnel from Light-weight LWAPP Access Points. This MIB provides configuration and status information about the 802.11 Access Points that have joined the controller. The relationship between CC and the LWAPP APs can be depicted as follows: +......+ +......+ +......+ +......+ + + + + + + + + + CC + + CC + + CC + + CC + + + + + + + + + +......+ +......+ +......+ +......+ .. . . . .. . . . . . . . . . . . . . . . . . . . . . . . +......+ +......+ +......+ +......+ +......+ + + + + + + + + + + + AP + + AP + + AP + + AP + + AP + + + + + + + + + + + +......+ +......+ +......+ +......+ +......+ . . . . . . . . . . . . . . . . . . . . . . . . +......+ +......+ +......+ +......+ +......+ + + + + + + + + + + + MN + + MN + + MN + + MN + + MN + + + + + + + + + + + +......+ +......+ +......+ +......+ +......+ The LWAPP tunnel exists between the controller and the APs. The MNs communicate with the APs through the protocol defined by the 802.11 standard. LWAPP APs, upon bootup, discover and join one of the controllers and the controller pushes the configuration, that includes the WLAN parameters, to the LWAPP APs. The APs then encapsulate all the 802.11 frames from wireless clients inside LWAPP frames and forward the LWAPP frames to the controller. GLOSSARY Access Point ( AP ) An entity that contains an 802.11 medium access control ( MAC ) and physical layer ( PHY ) interface and provides access to the distribution services via the wireless medium for associated clients. LWAPP APs encapsulate all the 802.11 frames in LWAPP frames and sends it to the controller to which it is logically connected. Basic Service Set Identifier (BSSID) The identifier for the service set comprising of all the 802.11 stations under the control of one coordinating Access Point. This identifier happens to be the MAC address of the dot11 radio interface of the Access Point. The wireless clients that associate with the Access Point get the wired uplink through this particular dot11 interface. Central Controller ( CC ) The central entity that terminates the LWAPP protocol tunnel from the LWAPP APs. Throughout this MIB, this entity also referred to as 'controller'. Light Weight Access Point Protocol ( LWAPP ) This is a generic protocol that defines the communication between the Access Points and the Central Controller. Mobile Node ( MN ) A roaming 802.11 wireless device in a wireless network associated with an access point. Station Management (SMT) This term refers to the internal management of the 802.11 protocol operations by the AP to work cooperatively with the other APs and 802.11 devices in the network. Link Latency Latency is round trip time between AP and controller. There is a continuous heart-beat between AP and controller. AP calculates latency for each time and sends to controller. AMSDU Aggregate MAC Service Data Unit. A structure containing multiple MSDUs, transported within a single (unfragmented) or multiple (fragmented) Data MPDU. DTLS Datagram Transport Layer Security (DTLS) protocol provides communications privacy for datagram protocols. The protocol allows client/server applications to communicate in a way that is designed to prevent eavesdropping, tampering, or message forgery. WIPS Wireless Intrusion Prevention System (WIPS) is a network device that monitors the radio spectrum for the presence of unauthorized access points (intrusion detection), and can automatically take countermeasures (intrusion prevention). SE Spectrum Expert is an application software, which when connected to Spectrum Intelligent Access Point, provides detailed RF spectrum plots and data, and assist in diagnosing network problems. REFERENCE [1] Part 11 Wireless LAN Medium Access Control ( MAC ) and Physical Layer ( PHY ) Specifications. [2] Draft-obara-capwap-lwapp-00.txt, IETF Light Weight Access Point Protocol.
Main OID:
ciscoLwappApMIB.1.3.6.1.4.1.9.9.513
227
Objects
Active
Status
9
Dependencies

Imported Objects

Objects

227 total
Object Name
ciscoLwappApMIB
MODULE-IDENTITY
.1.3.6.1.4.1.9.9.513
ciscoLwappApMIBNotifs
OBJECT IDENTIFIER
.1.3.6.1.4.1.9.9.513.0
ciscoLwappApIfRegulatoryDomainMismatchNotif
NOTIFICATION-TYPE
.1.3.6.1.4.1.9.9.513.0.1
ciscoLwappApCrash
NOTIFICATION-TYPE
.1.3.6.1.4.1.9.9.513.0.2
ciscoLwappApUnsupported
NOTIFICATION-TYPE
.1.3.6.1.4.1.9.9.513.0.3
ciscoLwappApAssociated
NOTIFICATION-TYPE
.1.3.6.1.4.1.9.9.513.0.4
ciscoLwappApPower
NOTIFICATION-TYPE
.1.3.6.1.4.1.9.9.513.0.5
ciscoLwappApRogueApDetected
NOTIFICATION-TYPE
.1.3.6.1.4.1.9.9.513.0.6
ciscoLwappApRogueApCleared
NOTIFICATION-TYPE
.1.3.6.1.4.1.9.9.513.0.7
ciscoLwappApWipsNotification
NOTIFICATION-TYPE
.1.3.6.1.4.1.9.9.513.0.8
ciscoLwappApNoDownlinkChannelNotify
NOTIFICATION-TYPE
.1.3.6.1.4.1.9.9.513.0.9
ciscoLwappApIfUpNotify
NOTIFICATION-TYPE
.1.3.6.1.4.1.9.9.513.0.10
ciscoLwappApIfDownNotify
NOTIFICATION-TYPE
.1.3.6.1.4.1.9.9.513.0.11
ciscoLwappApMIBObjects
OBJECT IDENTIFIER
.1.3.6.1.4.1.9.9.513.1
ciscoLwappAp
OBJECT IDENTIFIER
.1.3.6.1.4.1.9.9.513.1.1
cLApTable
SEQUENCE OF CLApEntry
.1.3.6.1.4.1.9.9.513.1.1.1
cLApEntry
CLApEntry
.1.3.6.1.4.1.9.9.513.1.1.1.1
cLApSysMacAddress
MacAddress (SNMPv2-TC)
.1.3.6.1.4.1.9.9.513.1.1.1.1.1
cLApIfMacAddressro
MacAddress (SNMPv2-TC)
.1.3.6.1.4.1.9.9.513.1.1.1.1.2
cLApMaxNumberOfDot11Slotsro
Unsigned32
.1.3.6.1.4.1.9.9.513.1.1.1.1.3
cLApEntPhysicalIndexro
PhysicalIndex (ENTITY-MIB)
.1.3.6.1.4.1.9.9.513.1.1.1.1.4
cLApNamerw
SnmpAdminString
.1.3.6.1.4.1.9.9.513.1.1.1.1.5
cLApUpTimero
TimeTicks (SNMPv2-SMI)
.1.3.6.1.4.1.9.9.513.1.1.1.1.6
cLLwappUpTimero
TimeTicks (SNMPv2-SMI)
.1.3.6.1.4.1.9.9.513.1.1.1.1.7
cLLwappJoinTakenTimero
TimeTicks (SNMPv2-SMI)
.1.3.6.1.4.1.9.9.513.1.1.1.1.8
cLApMaxNumberOfEthernetSlotsro
Unsigned32
.1.3.6.1.4.1.9.9.513.1.1.1.1.9
cLApPrimaryControllerAddressTyperw
InetAddressType (INET-ADDRESS-MIB)
.1.3.6.1.4.1.9.9.513.1.1.1.1.10
cLApPrimaryControllerAddressrw
InetAddress (INET-ADDRESS-MIB)
.1.3.6.1.4.1.9.9.513.1.1.1.1.11
cLApSecondaryControllerAddressTyperw
InetAddressType (INET-ADDRESS-MIB)
.1.3.6.1.4.1.9.9.513.1.1.1.1.12
cLApSecondaryControllerAddressrw
InetAddress (INET-ADDRESS-MIB)
.1.3.6.1.4.1.9.9.513.1.1.1.1.13
cLApTertiaryControllerAddressTyperw
InetAddressType (INET-ADDRESS-MIB)
.1.3.6.1.4.1.9.9.513.1.1.1.1.14
cLApTertiaryControllerAddressrw
InetAddress (INET-ADDRESS-MIB)
.1.3.6.1.4.1.9.9.513.1.1.1.1.15
cLApLastRebootReasonro
Enumeration
.1.3.6.1.4.1.9.9.513.1.1.1.1.16
cLApEncryptionEnablerw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.9.9.513.1.1.1.1.18
cLApFailoverPriorityrw
Enumeration
.1.3.6.1.4.1.9.9.513.1.1.1.1.19
cLApPowerStatusro
Enumeration
.1.3.6.1.4.1.9.9.513.1.1.1.1.20
cLApTelnetEnablerw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.9.9.513.1.1.1.1.21
cLApSshEnablerw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.9.9.513.1.1.1.1.22
cLApPreStdStateEnabledrw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.9.9.513.1.1.1.1.23
cLApPwrInjectorStateEnabledrw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.9.9.513.1.1.1.1.24
cLApPwrInjectorSelectionrw
Enumeration
.1.3.6.1.4.1.9.9.513.1.1.1.1.25
cLApPwrInjectorSwMacAddrrw
MacAddress (SNMPv2-TC)
.1.3.6.1.4.1.9.9.513.1.1.1.1.26
cLApWipsEnablerw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.9.9.513.1.1.1.1.27
cLApMonitorModeOptimizationrw
Enumeration
.1.3.6.1.4.1.9.9.513.1.1.1.1.28
cLApDomainNamerw
SnmpAdminString (SNMP-FRAMEWORK-MIB)
.1.3.6.1.4.1.9.9.513.1.1.1.1.29
cLApNameServerAddressTyperw
InetAddressType (INET-ADDRESS-MIB)
.1.3.6.1.4.1.9.9.513.1.1.1.1.30
cLApNameServerAddressrw
InetAddress (INET-ADDRESS-MIB)
.1.3.6.1.4.1.9.9.513.1.1.1.1.31
cLApAMSDUEnablerw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.9.9.513.1.1.1.1.32
cLApEncryptionSupportedrw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.9.9.513.1.1.1.1.33
cLApRogueDetectionEnabledrw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.9.9.513.1.1.1.1.34
cLApTcpMssrw
INTEGER (0 | 536..1363)
.1.3.6.1.4.1.9.9.513.1.1.1.1.35
cLApDataEncryptionStatusro
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.9.9.513.1.1.1.1.36
cLApNsiKeyro
DisplayString
.1.3.6.1.4.1.9.9.513.1.1.1.1.37
cLApAdminStatusrw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.9.9.513.1.1.1.1.38
cLApPortNumberro
InetPortNumber (INET-ADDRESS-MIB)
.1.3.6.1.4.1.9.9.513.1.1.1.1.39
cLApRetransmitCountrw
Unsigned32 UNITS "retries"
.1.3.6.1.4.1.9.9.513.1.1.1.1.40
cLApRetransmitTimeoutrw
Unsigned32 UNITS "seconds"
.1.3.6.1.4.1.9.9.513.1.1.1.1.41
cLApIfSmtParamTable
SEQUENCE OF CLApIfSmtParamEntry
.1.3.6.1.4.1.9.9.513.1.1.2
cLApIfSmtParamEntry
CLApIfSmtParamEntry
.1.3.6.1.4.1.9.9.513.1.1.2.1
cLApIfSmtDot11Bssidro
MacAddress (SNMPv2-TC)
.1.3.6.1.4.1.9.9.513.1.1.2.1.1
cLApCountryTable
SEQUENCE OF CLApCountryEntry
.1.3.6.1.4.1.9.9.513.1.1.3
cLApCountryEntry
CLApCountryEntry
.1.3.6.1.4.1.9.9.513.1.1.3.1
cLApCountryCoderw
DisplayString
.1.3.6.1.4.1.9.9.513.1.1.3.1.1
cLApCountryAllowedro
DisplayString
.1.3.6.1.4.1.9.9.513.1.1.3.1.2
ciscoLwappApIfRegulatoryDomainMismatchNotifEnabledrw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.9.9.513.1.1.4
ciscoLwappApCrashEnabledrw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.9.9.513.1.1.5
ciscoLwappApUnsupportedEnabledrw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.9.9.513.1.1.6
ciscoLwappApAssociatedEnabledrw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.9.9.513.1.1.7
ciscoLwappApIf
OBJECT IDENTIFIER
.1.3.6.1.4.1.9.9.513.1.2
cLApDot11IfTable
SEQUENCE OF CLApDot11IfEntry
.1.3.6.1.4.1.9.9.513.1.2.1
cLApDot11IfEntry
CLApDot11IfEntry
.1.3.6.1.4.1.9.9.513.1.2.1.1
cLApDot11IfSlotId
Unsigned32
.1.3.6.1.4.1.9.9.513.1.2.1.1.1
cLApDot11IfTypero
CLApIfType (CISCO-LWAPP-TC-MIB)
.1.3.6.1.4.1.9.9.513.1.2.1.1.2
cLApDot11IfRegDomainro
DisplayString
.1.3.6.1.4.1.9.9.513.1.2.1.1.3
cLApDot11nSupportro
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.9.9.513.1.2.1.1.4
cLAp11nChannelBandwidthrw
Enumeration
.1.3.6.1.4.1.9.9.513.1.2.1.1.5
cLApLomEnabledrwdeprecated
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.9.9.513.1.2.1.1.6
cLApLomFirstChannelrw
CLDot11Channel (CISCO-LWAPP-TC-MIB)
.1.3.6.1.4.1.9.9.513.1.2.1.1.7
cLApLomSecondChannelrw
CLDot11Channel (CISCO-LWAPP-TC-MIB)
.1.3.6.1.4.1.9.9.513.1.2.1.1.8
cLApLomThirdChannelrw
CLDot11Channel (CISCO-LWAPP-TC-MIB)
.1.3.6.1.4.1.9.9.513.1.2.1.1.9
cLApLomFourthChannelrw
CLDot11Channel (CISCO-LWAPP-TC-MIB)
.1.3.6.1.4.1.9.9.513.1.2.1.1.10
cLApExtensionChannelro
CLDot11Channel (CISCO-LWAPP-TC-MIB)
.1.3.6.1.4.1.9.9.513.1.2.1.1.11
cLApLegacyBeamFormingrw
Enumeration
.1.3.6.1.4.1.9.9.513.1.2.1.1.12
cLApCdpOverAirEnabledrw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.9.9.513.1.2.1.1.13
cLApDot11IfAdminStatusrw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.9.9.513.1.2.1.1.14
cLApEthernetIfTable
SEQUENCE OF CLApEthernetIfEntry
.1.3.6.1.4.1.9.9.513.1.2.2
cLApEthernetIfEntry
CLApEthernetIfEntry
.1.3.6.1.4.1.9.9.513.1.2.2.1
cLApEthernetIfSlotId
Unsigned32
.1.3.6.1.4.1.9.9.513.1.2.2.1.1
cLApEthernetIfNamero
SnmpAdminString
.1.3.6.1.4.1.9.9.513.1.2.2.1.2
cLApEthernetIfMacAddressro
MacAddress (SNMPv2-TC)
.1.3.6.1.4.1.9.9.513.1.2.2.1.3
cLApEthernetIfAdminStatusrw
Enumeration
.1.3.6.1.4.1.9.9.513.1.2.2.1.4
cLApEthernetIfOperStatusro
Enumeration
.1.3.6.1.4.1.9.9.513.1.2.2.1.5
cLApEthernetIfRxUcastPktsro
Counter32 UNITS "packets"
.1.3.6.1.4.1.9.9.513.1.2.2.1.6
cLApEthernetIfRxNUcastPktsro
Counter32 UNITS "packets"
.1.3.6.1.4.1.9.9.513.1.2.2.1.7
cLApEthernetIfTxUcastPktsro
Counter32 UNITS "packets"
.1.3.6.1.4.1.9.9.513.1.2.2.1.8
cLApEthernetIfTxNUcastPktsro
Counter32 UNITS "packets"
.1.3.6.1.4.1.9.9.513.1.2.2.1.9
cLApEthernetIfDuplexro
Enumeration
.1.3.6.1.4.1.9.9.513.1.2.2.1.10
cLApEthernetIfLinkSpeedro
Gauge32
.1.3.6.1.4.1.9.9.513.1.2.2.1.11
cLApEthernetIfPOEPowerro
Enumeration
.1.3.6.1.4.1.9.9.513.1.2.2.1.12
cLApEthernetIfRxTotalBytesro
Counter32 UNITS "Bytes"
.1.3.6.1.4.1.9.9.513.1.2.2.1.13
Showing 100 of 227 OID objects

CISCO-LWAPP-AP-MIB Technical Reference Overview

The CISCO-LWAPP-AP-MIB SNMP MIB module published by Cisco defines 227 managed OID objects, including 166 scalar/column metrics, 18 SNMP tables, and 11 trap/notification events anchored at base OID .1.3.6.1.4.1.9.9.513. Key tabular structures include cLApTable, cLApDot11IfTable, cLApEthernetIfTable, cLApDot11RadioTable, cLApCredentialsTable, cLApLinkLatencyTable. Monitored SNMP traps/notifications include ciscoLwappApIfRegulatoryDomainMismatchNotif, ciscoLwappApCrash, ciscoLwappApUnsupported, ciscoLwappApAssociated, ciscoLwappApPower, ciscoLwappApRogueApDetected.

Key OID Definitions in CISCO-LWAPP-AP-MIB

ciscoLwappApMIBMODULE-IDENTITYnot-accessible
.1.3.6.1.4.1.9.9.513

This MIB is intended to be implemented on all those devices operating as Central Controllers (CC) that terminate the Light Weight Access Point Protocol tunnel from Light-weight LWAPP Access Points. This MIB provides configuration and status information about the 802.11 Access Points that have joined the controller. The relationship between CC and the LWAPP APs can be depicted as follows: +......+ +......+ +......+ +......+ + + + + + + + + + CC + + CC + + CC + + CC + + + + + + + + + +......+ +......+ +......+ +......+ .. . . . .. . . . . . . . . . . . . . . . . . . . . . . . +......+ +......+ +......+ +......+ +......+ + + + + + + + + + + + AP + + AP + + AP + + AP + + AP + + + + + + + + + + + +......+ +......+ +......+ +......+ +......+ . . . . . . . . . . . . . . . . . . . . . . . . +......+ +......+ +......+ +......+ +......+ + + + + + + + + + + + MN + + MN + + MN + + MN + + MN + + + + + + + + + + + +......+ +......+ +......+ +......+ +......+ The LWAPP tunnel exists between the controller and the APs. The MNs communicate with the APs through the protocol defined by the 802.11 standard. LWAPP APs, upon bootup, discover and join one of the controllers and the controller pushes the configuration, that includes the WLAN parameters, to the LWAPP APs. The APs then encapsulate all the 802.11 frames from wireless clients inside LWAPP frames and forward the LWAPP frames to the controller. GLOSSARY Access Point ( AP ) An entity that contains an 802.11 medium access control ( MAC ) and physical layer ( PHY ) interface and provides access to the distribution services via the wireless medium for associated clients. LWAPP APs encapsulate all the 802.11 frames in LWAPP frames and sends it to the controller to which it is logically connected. Basic Service Set Identifier (BSSID) The identifier for the service set comprising of all the 802.11 stations under the control of one coordinating Access Point. This identifier happens to be the MAC address of the dot11 radio interface of the Access Point. The wireless clients that associate with the Access Point get the wired uplink through this particular dot11 interface. Central Controller ( CC ) The central entity that terminates the LWAPP protocol tunnel from the LWAPP APs. Throughout this MIB, this entity also referred to as 'controller'. Light Weight Access Point Protocol ( LWAPP ) This is a generic protocol that defines the communication between the Access Points and the Central Controller. Mobile Node ( MN ) A roaming 802.11 wireless device in a wireless network associated with an access point. Station Management (SMT) This term refers to the internal management of the 802.11 protocol operations by the AP to work cooperatively with the other APs and 802.11 devices in the network. Link Latency Latency is round trip time between AP and controller. There is a continuous heart-beat between AP and controller. AP calculates latency for each time and sends to controller. AMSDU Aggregate MAC Service Data Unit. A structure containing multiple MSDUs, transported within a single (unfragmented) or multiple (fragmented) Data MPDU. DTLS Datagram Transport Layer Security (DTLS) protocol provides communications privacy for datagram protocols. The protocol allows client/server applications to communicate in a way that is designed to prevent eavesdropping, tampering, or message forgery. WIPS Wireless Intrusion Prevention System (WIPS) is a network device that monitors the radio spectrum for the presence of unauthorized access points (intrusion detection), and can automatically take countermeasures (intrusion prevention). SE Spectrum Expert is an application software, which when connected to Spectrum Intelligent Access Point, provides detailed RF spectrum plots and data, and assist in diagnosing network problems. REFERENCE [1] Part 11 Wireless LAN Medium Access Control ( MAC ) and Physical Layer ( PHY ) Specifications. [2] Draft-obara-capwap-lwapp-00.txt, IETF Light Weight Access Point Protocol.

cLApTableSEQUENCEnot-accessible
.1.3.6.1.4.1.9.9.513.1.1.1

This table represents the information about the 802.11 LWAPP Access Points that have joined the controller. LWAPP APs exchange configuration messages with the controller and get the required configuration for their 802.11 related operations, after they join the controller.

cLApDot11IfTableSEQUENCEnot-accessible
.1.3.6.1.4.1.9.9.513.1.2.1

This table represents the information about the basic functional parameters corresponding to the dot11 interfaces of the APs that have joined the controller.

cLApEthernetIfTableSEQUENCEnot-accessible
.1.3.6.1.4.1.9.9.513.1.2.2

This table represents the information about the basic functional parameters corresponding to the Ethernet interfaces of the APs that have joined the controller.

cLApDot11RadioTableSEQUENCEnot-accessible
.1.3.6.1.4.1.9.9.513.1.2.3

This table represents the information about the basic functional parameters of the radios of the APs that have joined the controller.

cLApCredentialsTableSEQUENCEnot-accessible
.1.3.6.1.4.1.9.9.513.1.4.4

This table provides the information about the credentials of the 802.11 LWAPP Access Points that have joined the controller. Rows are added to this table whenever, new APs are joined to this controller, and rows are deleted whenever APs gets disjoined from the controller.

cLApLinkLatencyTableSEQUENCEnot-accessible
.1.3.6.1.4.1.9.9.513.1.5.1

This table represents the link latency configuration for each AP. An entry is automatically added to this table when an Access Points Joins controller. Entry is removed from this table when AP disassociates from the controllers.

cLApLinkLatencyStatsTableSEQUENCEnot-accessible
.1.3.6.1.4.1.9.9.513.1.5.2

This table represents the link latency statistics calculated for each AP. An entry is automatically added by the controller when a 'cLApLinkLatencyEnable' is enabled on an Access Point. Entry is deleted when 'cLApLinkLatencyEnable' is disabled on the Access Point.

cLApIfSmtParamTableSEQUENCEnot-accessible
.1.3.6.1.4.1.9.9.513.1.1.2

This table represents the station management information in the APs that have joined the controller. Information populated through the entries of this table is used by the AP to perform the expected 802.11 operations on the respective dot11 interfaces to coordinate with other 802.11 devices in the network. Since this table has the indices defined in the tables cLApTable and cLApDot11IfTable, an entry in this table is automatically removed when the respective entry is removed in either of those tables.

cLApCountryTableSEQUENCEnot-accessible
.1.3.6.1.4.1.9.9.513.1.1.3

This table represents the country settings for the 802.11 LWAPP Access Points that have joined the controller. An entry is automatically added by the controller when a Access Point joins the controller. The entry is removed when Access Point disasscociates from the controller.

cLApSeClientTableSEQUENCEnot-accessible
.1.3.6.1.4.1.9.9.513.1.8

This table represents the information about the details of Spectrum Expert client connected to radio interface of APs

cLApFastHbTimerTableSEQUENCEnot-accessible
.1.3.6.1.4.1.9.9.513.1.3.1

This table contains entries for AP fast heartbeat timers configured in the controller. At startup, all the entries in this table are set up by the central controller. A management application can later change the values in this table.

cLApGlobalDot11IfTableSEQUENCEnot-accessible
.1.3.6.1.4.1.9.9.513.1.3.12

This table is used to configure the global dot11 parameters per slot id, represented by cLApDot11IfSlotId, of the radio interface in all the APs joined with the controller.

cLApGlobalEthernetIfTableSEQUENCEnot-accessible
.1.3.6.1.4.1.9.9.513.1.3.13

This table is used to configure the global parameters on Ethernet interfaces of all the APs joined with the controller.

cLApDot11IfAntennaTableSEQUENCEnot-accessible
.1.3.6.1.4.1.9.9.513.1.2.4

This table represents the information about the basic functional parameters corresponding to the antenna on dot11 interfaces of the APs that have joined the controller.

cLApVlanIfTableSEQUENCEnot-accessible
.1.3.6.1.4.1.9.9.513.1.2.5

This table represents the information about the basic functional parameters corresponding to the Ethernet interfaces of the APs that have joined the controller.

cLApVlanListTableSEQUENCEnot-accessible
.1.3.6.1.4.1.9.9.513.1.2.6

This table represents the information about the basic functional parameters corresponding to the VLAN Ethernet interfaces of the APs that have joined the controller.

cLAp802dot1xSupplicantTableSEQUENCEnot-accessible
.1.3.6.1.4.1.9.9.513.1.7.4

This table provides the information about the 802.1x Supplicant credentials of the 802.11 LWAPP Access Points that have joined the controller. Rows are added to this table whenever, new APs are joined to this controller, and rows are deleted whenever APs gets disjoined from the controller.

cLApDot11GlobalConfigTableSEQUENCEnot-accessible
.1.3.6.1.4.1.9.9.513.1.2.7

This table represents the information about the global attributes of the radio interface, that would be applicable for all the APs that join the controller.

ciscoLwappApIfRegulatoryDomainMismatchNotifNOTIFICATION-TYPEnot-accessible
.1.3.6.1.4.1.9.9.513.0.1

This notification is generated if an AP radio's regulatory domain doesn't match the country the controller is configured for. Due to the mismatch, the AP will fail to associate with the controller.

ciscoLwappApCrashNOTIFICATION-TYPEnot-accessible
.1.3.6.1.4.1.9.9.513.0.2

This notification is generated after an AP rejoins the controller after a crash. Once the AP joins, the controller will get the crash file from the AP and sends this notification.

ciscoLwappApUnsupportedNOTIFICATION-TYPEnot-accessible
.1.3.6.1.4.1.9.9.513.0.3

This notification is generated after an unsupported AP tries to join the controller.

ciscoLwappApAssociatedNOTIFICATION-TYPEnot-accessible
.1.3.6.1.4.1.9.9.513.0.4

This notification is generated whenever an AP joins the controller successfully. This notification contains information about the last reboot reason and Data Encryption status of the AP.

ciscoLwappApPowerNOTIFICATION-TYPEnot-accessible
.1.3.6.1.4.1.9.9.513.0.5

This notification is generated whenever an AP detects low power from Ethernet.

More MIBs from Cisco

Browse all CiscoMIBs →
CISCO-UNIFIED-COMPUTING-COMPUTE-MIB

The CISCO-UNIFIED-COMPUTING-COMPUTE-MIB provides SNMP-based monitoring and management of Cisco UCS compute blades, servers, and chassis components, exposing critical metrics such as CPU utilization, memory usage, thermal sensor readings, power supply status, and interface operational states. This module enables granular visibility into the health and performance of the Cisco Unified Computing System's compute subsystems for capacity planning and fault isolation.

1401 objects→
CISCO-UNIFIED-COMPUTING-STORAGE-MIB

The CISCO-UNIFIED-COMPUTING-STORAGE-MIB facilitates SNMP-based monitoring and management of storage subsystems, including Fibre Channel and iSCSI interfaces, within the Cisco Unified Computing System (UCS) fabric interconnects and blade servers. It exposes critical operational metrics such as port status, error counters, throughput statistics, and storage controller health states to enable granular visibility into the storage infrastructure.

1295 objects→
CISCO-UNIFIED-COMPUTING-VNIC-MIB

The CISCO-UNIFIED-COMPUTING-VNIC-MIB enables SNMP-based monitoring and management of Virtual Network Interface Card (vNIC) attributes, including operational status, traffic counters, and binding configurations, within the Cisco Unified Computing System (UCS) fabric interconnects and server blades.

1161 objects→
CERENT-GENERIC-MIB

SNMP MIB module

984 objects→
CISCO-UNIFIED-COMPUTING-BIOS-MIB

The CISCO-UNIFIED-COMPUTING-BIOS-MIB enables SNMP-based monitoring and configuration of BIOS-level parameters, firmware versions, and hardware initialization states within Cisco Unified Computing System (UCS) servers. It provides visibility into critical server boot diagnostics, BIOS settings, and hardware readiness indicators to facilitate low-level infrastructure management and troubleshooting.

937 objects→
CISCO-UNIFIED-COMPUTING-ETHER-MIB

The CISCO-UNIFIED-COMPUTING-ETHER-MIB provides SNMP management interfaces for monitoring Ethernet interface statistics, link states, and error counters on Cisco Unified Computing System (UCS) fabric interconnects and blade server line cards. This module enables the tracking of physical layer connectivity, port throughput, and packet error rates within the UCS Ethernet switching infrastructure.

920 objects→