CISCO-FCOE-MIB
AI MIB Summary
The CISCO-FCOE-MIB manages and monitors Cisco Fibre Channel over Ethernet (FCoE) infrastructure by exposing Virtual FC (VFC) interface states for VF_Port and VE_Port entities, alongside critical configuration parameters such as VSAN-to-VLAN mapping, FC-MAP values for FPMA mode, and FIP snooping attributes.
This MIB module is for configuring and monitoring Fibre Channel over Ethernet (FCoE) related entities. This MIB defines the Virtual FC (VFC) Interface as an object that represents either a VF_Port or a VE_Port on the FCF. Virtual FC interfaces can be either statically created or dynamically created at the time of FIP based FLOGI or ELP request.
In this document the term VSAN ID is used interchangeably with Fabric Index defined in the T11 standards.
Terminologies used in this MIB are defined by the T11 FCoE standard. Refer to www.t11.org.
This MIB also supports configuration of the following objects:
- Mapping of FCoE VLAN ID used to carry traffic for a VSAN ID
- FC-MAP value used by the FCF operating in FPMA mode
- FIP snooping related objects
Main OID:
ciscoFCoEMIB.1.3.6.1.4.1.9.9.673
38
Objects
Active
Status
9
Dependencies
Imported Objects
Objects
38 total| Object Name |
|---|
ciscoFCoEMIBThis MIB module is for configuring and monitoring Fibre Channel
over Ethernet (FCoE) related entities. This MIB defines the
Virtual FC (VFC) Interface as an object that represents either
a VF_Port or a VE_Port on the FCF. Virtual FC interfaces can be
either statically created or dynamically created at the time of
FIP based FLOGI or ELP request.
In this document the term VSAN ID is used interchangeably with
Fabric Index defined in the T11 standards.
Terminologies used in this MIB are defined by the T11 FCoE
standard. Refer to www.t11.org.
This MIB also supports configuration of the following objects:
- Mapping of FCoE VLAN ID used to carry traffic for a VSAN ID
- FC-MAP value used by the FCF operating in FPMA mode
- FIP snooping related objects MODULE-IDENTITY .1.3.6.1.4.1.9.9.673 |
ciscoFCoEMIBObjects OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.673.1 |
cfcoeConfig OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.673.1.1 |
cfcoeCfgTableThis table facilitates configuration of FCoE parameters
on a per Fibre Channel management instance. SEQUENCE OF CfcoeCfgEntry .1.3.6.1.4.1.9.9.673.1.1.1 |
cfcoeCfgEntryThere is one entry in this table for each
Fibre Channel management instance. CfcoeCfgEntry .1.3.6.1.4.1.9.9.673.1.1.1.1 |
cfcoeCfgFcmapThis object configures the FC-MAP value used by the FCF
when operating in FPMA mode. The default value is 0EFC00h,
as written in the standard.rw OCTET STRING .1.3.6.1.4.1.9.9.673.1.1.1.1.1 |
cfcoeCfgDynamicVfcCreationThis object allows the user to enable (TRUE)
or disable (FALSE) dynamic VFC interface creation on the FCF.
When set to TRUE VFC interfaces are dynamically created when a
FIP based FLOGI or ELP request is received.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.673.1.1.1.1.2 |
cfcoeCfgDynamicVfcAgeTimerThis ageing timer (in seconds) is used by the FCF to age out
dynamically created VFC interfaces. The default value is
300 seconds.rw Unsigned32 .1.3.6.1.4.1.9.9.673.1.1.1.1.3 |
cfcoeCfgDefaultFCFPriorityThe FIP priority value advertised by the FCF to ENodes by
default. cfcoeStaticVfcFCFPriority configured for a VFC
interface overrides this setting for the ENode associated
with the VFC.rw Unsigned32 .1.3.6.1.4.1.9.9.673.1.1.1.1.4 |
cfcoeCfgDATovThe Discovery_Advertisement_Timeout value configured for
the FCF. This is used as the timeout value in seconds by
the FCF to send periodic Discovery Advertisements.rw Unsigned32 .1.3.6.1.4.1.9.9.673.1.1.1.1.5 |
cfcoeCfgAddressingModeAddressing mode(s) supported by the FCF. Implementations should
fail set requests for unsupported modes.rw Enumeration .1.3.6.1.4.1.9.9.673.1.1.1.1.6 |
cfcoeVLANTableThis table facilitates configuration of VLAN and Fabric (VSAN)
associations in an FCoE network. FCoE forwarding for a fabric
is over a VLAN in a L2 Ethernet network. That is, reachability
between the ENode/remote-FCF and an FCF for a given fabric is
determined by the reachability provided by the Ethernet network
on the corresponding VLAN.
An active entry in this table indicates the VLAN that is used
to transport FCoE traffic for a certain VSAN.
Some implmentations may allow traffic from only one VSAN to be
transported over a given VLAN. Such implmentations should
prevent multiple entries with the same VLAN ID or the VSAN ID
from being created in this table.
Modifying existing VLAN-VSAN associations is not supported.
Entries must be deleted first and then recreated. SEQUENCE OF CfcoeVLANEntry .1.3.6.1.4.1.9.9.673.1.1.2 |
cfcoeVLANEntryThere is one entry in this table for each VLAN that is
designated to transport FCoE traffic for a given fabric
(VSAN). CfcoeVLANEntry .1.3.6.1.4.1.9.9.673.1.1.2.1 |
cfcoeVLANIndexThis object identifies the VLAN ID that FCoE FCF function is
being enabled for. VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.9.9.673.1.1.2.1.1 |
cfcoeFabricIndexThis object identifies the Fabric Index of the VSAN traffic
for which can be transported over the VLAN identified by
cfcoeVLANIndex. T11FabricIndex (T11-TC-MIB) .1.3.6.1.4.1.9.9.673.1.1.2.1.2 |
cfcoeVLANOperStateOperational state of this VLAN-VSAN association entry.
The 'up' state is achieved when both the VSAN and VLAN
are valid.ro Enumeration .1.3.6.1.4.1.9.9.673.1.1.2.1.3 |
cfcoeVLANRowStatusThe status of this conceptual row. The RowStatus becomes active
on successful creation of an entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.9.9.673.1.1.2.1.4 |
cfcoeStaticVfcTableThis table facilitates the creation and deletion of static
VFC interfaces. While VFCs can be dynamically created based on
FIP FLOGI/ELP requests users may want to associate certain
pre-configured policy for a particular ENode or a remote-FCF.
In such cases static VFC creation becomes necessary. In addition
to creating a static VFC it also needs to be associated to an
ENode or remote-FCF. The VFC binding provides such an
associaton. Binding may occur after a VFC is created. SEQUENCE OF CfcoeStaticVfcEntry .1.3.6.1.4.1.9.9.673.1.1.3 |
cfcoeStaticVfcEntryThere is one entry in this table for each statically created
VFC Interface. CfcoeStaticVfcEntry .1.3.6.1.4.1.9.9.673.1.1.3.1 |
cfcoeStaticVfcIndexThis index uniquely identifies a static VFC entry in this
table. Unsigned32 .1.3.6.1.4.1.9.9.673.1.1.3.1.1 |
cfcoeStaticVfcFCFPriorityIf this VFC is for a VF_Port this object is used to configure
FCF priority to be advertised to the ENode associated with the
VFC.rw Unsigned32 .1.3.6.1.4.1.9.9.673.1.1.3.1.2 |
cfcoeStaticVfcBindTypeThe mechanism to identify the ENode associated with this VFC
if it is of type VF_Port or to identify the remote-FCF
associated with this VFC if it is of type VE_Port.rw VfcBindType .1.3.6.1.4.1.9.9.673.1.1.3.1.3 |
cfcoeStaticVfcBindIfIndexThis object allows for configuration of ifIndex of
the ethernet interface over which the FCF reaches
the ENode or the remote-FCF that this VFC identifies.
This object is to be used only when the ENode or the
remote-FCF is directly connected to the FCF over a specific
ethernet interface. If the ENode or remote-FCF is not directly
connected to the FCF, this field must be set to zero.rw InterfaceIndexOrZero (IF-MIB) .1.3.6.1.4.1.9.9.673.1.1.3.1.4 |
cfcoeStaticVfcBindMACAddressThis object allows the user to configure MAC address of the
ENode or the remote-FCF that this VFC interface identifies.
An ENode or remote-FCF is associated to this VFC only if the
source MAC address in the FIP frames matches with this object.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.9.9.673.1.1.3.1.5 |
cfcoeStaticVfcIfIndexThe ifIndex of this virtual FC interface.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.9.9.673.1.1.3.1.6 |
cfcoeStaticVfcCreationTimeThe timestamp of this entry's creation time.ro TimeStamp (SNMPv2-TC) .1.3.6.1.4.1.9.9.673.1.1.3.1.7 |
cfcoeStaticVfcFailureCauseThe cause of failure for the last bind operation. This
object will be zero length if and only if the bind is
successful.ro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.9.9.673.1.1.3.1.8 |
cfcoeStaticVfcRowStatusThe status of this conceptual row. The RowStatus becomes active
on successful creation of a virtual interface. The VFC must be
bound before it can become operational.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.9.9.673.1.1.3.1.9 |
cfcoeFipSnoopingObjects OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.673.1.2 |
cfcoeFipSnoopingEnableThis object is used to enable or disable FIP Snooping on an
Ethernet Bridge.rw Enumeration .1.3.6.1.4.1.9.9.673.1.2.1 |
cfcoeFipSnoopingFcmapThis object configures the FC-MAP value associated with the
FIP snooping Ethernet bridge.rw OCTET STRING .1.3.6.1.4.1.9.9.673.1.2.2 |
cfcoeEnodeIntfTableThe (conceptual) table containing the interfaces on an
Ethernet bridge that are directly connected to ENodes.
A FIP Snooping bridge will automatically configure ACLs on
these interfaces based on FIP login requests and responses. SEQUENCE OF CfcoeEnodeIntfEntry .1.3.6.1.4.1.9.9.673.1.2.3 |
cfcoeEnodeIntfEntryAn entry (conceptual row) in the cfcoeEnodeIntfTable,
representing an interface directly connected to an ENode
on the Ethernet Bridge. CfcoeEnodeIntfEntry .1.3.6.1.4.1.9.9.673.1.2.3.1 |
cfcoeEnodeIntfIfIndexThe ifIndex of the interface on the Ethernet bridge connected
to an Enode. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.9.9.673.1.2.3.1.1 |
cfcoeEnodeIntfRowStatusThe status of this conceptual row.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.9.9.673.1.2.3.1.2 |
ciscoFCoEMIBConformance OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.673.2 |
cFCoEMIBCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.673.2.1 |
cFCoEMIBGroups OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.673.2.2 |