CISCO-ATM-TRUNK-MIB
The CISCO-ATM-TRUNK-MIB monitors and manages Cisco ATM trunking interfaces carrying voice and Nx64 TDM services over AAL2, AAL5, or AAL1 adaptation layers. It tracks critical performance and fault metrics including PVC/SVC states, TDM timeslot utilization, AAL error counters, and signaling indicators such as AIS, RAI, and RDI for Digital Signal Processing (DSP) and Voice Activity Detection (VAD) operations.
Imported Objects
Objects
97 total| Object Name |
|---|
ciscoAtmTrunkMIB MODULE-IDENTITY .1.3.6.1.4.1.9.9.351 |
SNMPv2-CONF Unknown .1.3.6.1.4.1.9.9.351 |
cAtmTrunkMIBNotifications OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.351.0 |
cAtmTrunkMIBObjects OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.351.1 |
cAtmTrunkCidConfig OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.351.1.1 |
catmtCidTable SEQUENCE OF CatmtCidEntry .1.3.6.1.4.1.9.9.351.1.1.1 |
catmtCidEntry CatmtCidEntry .1.3.6.1.4.1.9.9.351.1.1.1.1 |
catmtCidVpi Unsigned32 .1.3.6.1.4.1.9.9.351.1.1.1.1.1 |
catmtCidVci Unsigned32 .1.3.6.1.4.1.9.9.351.1.1.1.1.2 |
catmtCid Integer32 .1.3.6.1.4.1.9.9.351.1.1.1.1.3 |
catmtCidDs1rw InterfaceIndex (IF-MIB) .1.3.6.1.4.1.9.9.351.1.1.1.1.4 |
catmtCidDs0GroupIndexrw Integer32 .1.3.6.1.4.1.9.9.351.1.1.1.1.5 |
catmtCidProfileTyperw CiscoAal2ProfileType (CISCO-VOICE-AALX-PROFILE-MIB) .1.3.6.1.4.1.9.9.351.1.1.1.1.6 |
catmtCidProfileNumberrw CiscoAal2ProfileNumber (CISCO-VOICE-AALX-PROFILE-MIB) .1.3.6.1.4.1.9.9.351.1.1.1.1.7 |
catmtCidVoiceCodecrw CvcSpeechCoderRate (CISCO-VOICE-COMMON-DIAL-CONTROL-MIB) .1.3.6.1.4.1.9.9.351.1.1.1.1.8 |
catmtCidVBDCodecrw CvcCoderTypeRate (CISCO-VOICE-COMMON-DIAL-CONTROL-MIB) .1.3.6.1.4.1.9.9.351.1.1.1.1.9 |
catmtCidNx64Enablerw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.351.1.1.1.1.10 |
catmtCidNx64Profilerw Integer32 .1.3.6.1.4.1.9.9.351.1.1.1.1.11 |
catmtCidStateBitMapro Bits .1.3.6.1.4.1.9.9.351.1.1.1.1.12 |
catmtCidRepetitionrw ConfigIterator (CISCO-TC) .1.3.6.1.4.1.9.9.351.1.1.1.1.13 |
catmtCidRepetitionOwnerrw OwnerString (RMON-MIB) .1.3.6.1.4.1.9.9.351.1.1.1.1.14 |
catmtCidRepetitionResultro BulkConfigResult (CISCO-TC) .1.3.6.1.4.1.9.9.351.1.1.1.1.15 |
catmtCidRowStatusrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.9.9.351.1.1.1.1.16 |
cAtmTrunkCidConnStats OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.351.1.2 |
catmtCidStatsTable SEQUENCE OF CatmtCidStatsEntry .1.3.6.1.4.1.9.9.351.1.2.1 |
catmtCidStatsEntry CatmtCidStatsEntry .1.3.6.1.4.1.9.9.351.1.2.1.1 |
catmtCidSentPacketsro Counter32SinceReset UNITS "packets" .1.3.6.1.4.1.9.9.351.1.2.1.1.1 |
catmtCidRcvdPacketsro Counter32SinceReset UNITS "packets" .1.3.6.1.4.1.9.9.351.1.2.1.1.2 |
catmtCidSentOctetsro Counter32SinceReset UNITS "bytes" .1.3.6.1.4.1.9.9.351.1.2.1.1.3 |
catmtCidRcvdOctetsro Counter32SinceReset UNITS "bytes" .1.3.6.1.4.1.9.9.351.1.2.1.1.4 |
catmtCidLostPacketsro Counter32SinceReset UNITS "packets" .1.3.6.1.4.1.9.9.351.1.2.1.1.5 |
catmtCidJitterro Gauge32 .1.3.6.1.4.1.9.9.351.1.2.1.1.6 |
catmtCidExtAISCntsro Counter32SinceReset .1.3.6.1.4.1.9.9.351.1.2.1.1.7 |
catmtCidExtRAICntsro Counter32SinceReset .1.3.6.1.4.1.9.9.351.1.2.1.1.8 |
catmtCidConnAISCntsro Counter32SinceReset .1.3.6.1.4.1.9.9.351.1.2.1.1.9 |
catmtCidConnRDICntsro Counter32SinceReset .1.3.6.1.4.1.9.9.351.1.2.1.1.10 |
catmtCidNx64FramesTxToTDMro Counter32SinceReset .1.3.6.1.4.1.9.9.351.1.2.1.1.11 |
catmtCidNx64FramesRxFromTDMro Counter32SinceReset .1.3.6.1.4.1.9.9.351.1.2.1.1.12 |
catmtCidNx64EncBytesTxToTDMro Counter32SinceReset .1.3.6.1.4.1.9.9.351.1.2.1.1.13 |
catmtCidNx64EncBytesRxFromTDMro Counter32SinceReset .1.3.6.1.4.1.9.9.351.1.2.1.1.14 |
catmtCidNx64InvalidFCSFramesro Counter32SinceReset .1.3.6.1.4.1.9.9.351.1.2.1.1.15 |
catmtCidNx64AbortSeqFramesro Counter32SinceReset .1.3.6.1.4.1.9.9.351.1.2.1.1.16 |
catmtCidNx64InvalidShortFramesro Counter32SinceReset .1.3.6.1.4.1.9.9.351.1.2.1.1.17 |
catmtCidNx64InvalidLongFramesro Counter32SinceReset .1.3.6.1.4.1.9.9.351.1.2.1.1.18 |
catmtCidNx64NoByteAlignErrorFramesro Counter32SinceReset .1.3.6.1.4.1.9.9.351.1.2.1.1.19 |
catmtCidNx64RASTimeOutFramesro Counter32SinceReset .1.3.6.1.4.1.9.9.351.1.2.1.1.20 |
catmtCidLastResetTimero TimeStamp (SNMPv2-TC) .1.3.6.1.4.1.9.9.351.1.2.1.1.21 |
catmtCidCounterClearrw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.351.1.2.1.1.22 |
cAtmTrunkAal1Config OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.351.1.3 |
catmtAal1Table SEQUENCE OF CatmtAal1Entry .1.3.6.1.4.1.9.9.351.1.3.1 |
catmtAal1Entry CatmtAal1Entry .1.3.6.1.4.1.9.9.351.1.3.1.1 |
catmtAal1Vpi Unsigned32 .1.3.6.1.4.1.9.9.351.1.3.1.1.1 |
catmtAal1Vci Unsigned32 .1.3.6.1.4.1.9.9.351.1.3.1.1.2 |
catmtAal1Ds1rw InterfaceIndex (IF-MIB) .1.3.6.1.4.1.9.9.351.1.3.1.1.3 |
catmtAal1Ds0GroupIndexrw Integer32 .1.3.6.1.4.1.9.9.351.1.3.1.1.4 |
catmtAal1Nx64Profilerw Integer32 .1.3.6.1.4.1.9.9.351.1.3.1.1.5 |
catmtAal1RowStatusrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.9.9.351.1.3.1.1.6 |
cAtmTrunkAal1ConnStats OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.351.1.4 |
catmtAal1StatsTable SEQUENCE OF CatmtAal1StatsEntry .1.3.6.1.4.1.9.9.351.1.4.1 |
catmtAal1StatsEntry CatmtAal1StatsEntry .1.3.6.1.4.1.9.9.351.1.4.1.1 |
catmtAal1TxCellsro Counter32SinceReset .1.3.6.1.4.1.9.9.351.1.4.1.1.1 |
catmtAal1RxCellsro Counter32SinceReset .1.3.6.1.4.1.9.9.351.1.4.1.1.2 |
catmtAal1TxPayloadBytesro Counter32SinceReset .1.3.6.1.4.1.9.9.351.1.4.1.1.3 |
catmtAal1RxPayloadBytesro Counter32SinceReset .1.3.6.1.4.1.9.9.351.1.4.1.1.4 |
catmtAal1Jitterro Gauge32 .1.3.6.1.4.1.9.9.351.1.4.1.1.5 |
catmtAal1LastResetTimero TimeStamp (SNMPv2-TC) .1.3.6.1.4.1.9.9.351.1.4.1.1.6 |
catmtAal1CounterClearrw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.351.1.4.1.1.7 |
cAtmTrunkAal5Config OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.351.1.5 |
catmtAal5Table SEQUENCE OF CatmtAal5Entry .1.3.6.1.4.1.9.9.351.1.5.1 |
catmtAal5Entry CatmtAal5Entry .1.3.6.1.4.1.9.9.351.1.5.1.1 |
catmtAal5Vpi Unsigned32 .1.3.6.1.4.1.9.9.351.1.5.1.1.1 |
catmtAal5Vci Unsigned32 .1.3.6.1.4.1.9.9.351.1.5.1.1.2 |
catmtAal5Ds1rw InterfaceIndex (IF-MIB) .1.3.6.1.4.1.9.9.351.1.5.1.1.3 |
catmtAal5Ds0GroupIndexrw Integer32 .1.3.6.1.4.1.9.9.351.1.5.1.1.4 |
catmtAal5Nx64Profilerw Integer32 .1.3.6.1.4.1.9.9.351.1.5.1.1.5 |
catmtAal5RowStatusrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.9.9.351.1.5.1.1.6 |
cAtmTrunkAal5ConnStats OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.351.1.6 |
catmtAal5StatsTable SEQUENCE OF CatmtAal5StatsEntry .1.3.6.1.4.1.9.9.351.1.6.1 |
catmtAal5StatsEntry CatmtAal5StatsEntry .1.3.6.1.4.1.9.9.351.1.6.1.1 |
catmtAal5SentPacketsro Counter32SinceReset UNITS "packets" .1.3.6.1.4.1.9.9.351.1.6.1.1.1 |
catmtAal5RcvdPacketsro Counter32SinceReset UNITS "packets" .1.3.6.1.4.1.9.9.351.1.6.1.1.2 |
catmtAal5SentOctetsro Counter32SinceReset UNITS "bytes" .1.3.6.1.4.1.9.9.351.1.6.1.1.3 |
catmtAal5RcvdOctetsro Counter32SinceReset UNITS "bytes" .1.3.6.1.4.1.9.9.351.1.6.1.1.4 |
catmtAal5FramesTxToTDMro Counter32SinceReset .1.3.6.1.4.1.9.9.351.1.6.1.1.5 |
catmtAal5FramesRxFromTDMro Counter32SinceReset .1.3.6.1.4.1.9.9.351.1.6.1.1.6 |
catmtAal5EncBytesTxToTDMro Counter32SinceReset .1.3.6.1.4.1.9.9.351.1.6.1.1.7 |
catmtAal5EncBytesRxFromTDMro Counter32SinceReset .1.3.6.1.4.1.9.9.351.1.6.1.1.8 |
catmtAal5InvalidFCSFramesro Counter32SinceReset .1.3.6.1.4.1.9.9.351.1.6.1.1.9 |
catmtAal5AbortSeqFramesro Counter32SinceReset .1.3.6.1.4.1.9.9.351.1.6.1.1.10 |
catmtAal5InvalidShortFramesro Counter32SinceReset .1.3.6.1.4.1.9.9.351.1.6.1.1.11 |
catmtAal5InvalidLongFramesro Counter32SinceReset .1.3.6.1.4.1.9.9.351.1.6.1.1.12 |
catmtAal5NoByteAlignErrorFramesro Counter32SinceReset .1.3.6.1.4.1.9.9.351.1.6.1.1.13 |
catmtAal5LastResetTimero TimeStamp (SNMPv2-TC) .1.3.6.1.4.1.9.9.351.1.6.1.1.14 |
catmtAal5CounterClearrw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.351.1.6.1.1.15 |
cAtmTrunkMIBConformance OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.351.2 |
cAtmTrunkMIBCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.351.2.1 |
cAtmTrunkMIBGroups OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.351.2.2 |
CISCO-ATM-TRUNK-MIB Technical Reference Overview
The CISCO-ATM-TRUNK-MIB SNMP MIB module published by Cisco defines 97 managed OID objects, including 73 scalar/column metrics, 6 SNMP tables, and 0 trap/notification events anchored at base OID .1.3.6.1.4.1.9.9.351. Key tabular structures include catmtCidTable, catmtCidStatsTable, catmtAal1Table, catmtAal1StatsTable, catmtAal5Table, catmtAal5StatsTable.
Key OID Definitions in CISCO-ATM-TRUNK-MIB
.1.3.6.1.4.1.9.9.351The MIB for voice and Nx64 over ATM Trunking applications. The following lists the abbreviations used in this MIB: AAL ATM Adaption Layer AIS Alarm Indication Signal CID Channel Identifier DSP Digital Signal Processing DTMF Dual Tone Multi Frequency FCS Frame Check Sequence TDM Time Division Multiplexing PVC Permanent Virtual Circuit RAI Remote Alarm Indication RDI Remote Defect Indication SID Silence Insertion Descriptor SVC Switched Virtual Circuit VAD Voice Activity Detection VBD Voice Band Data VC Virtual Circuit
.1.3.6.1.4.1.9.9.351.1.1.1This table is used to establish the mapping of one or more DS0 channels from a single DS1 interface to an AAL2 connection identified by a Channel IDentification number(CID). This table is created and used for ATM AAL2 trunking applications including both voice and data.
.1.3.6.1.4.1.9.9.351.1.2.1This table contains the statistical information on a per CID connection basis for AAL2 Trunking applications.
.1.3.6.1.4.1.9.9.351.1.3.1This table is used to establish the mapping of a DS0 to an AAL1 ATM connection. This table is created and used for ATM AAL1 trunking applications only.
.1.3.6.1.4.1.9.9.351.1.4.1This table contains the statistics information on a per AAL1 connection basis for ATM AAL1 Trunking applications.
.1.3.6.1.4.1.9.9.351.1.5.1This table is used to establish the mapping of a DS0 to an AAL5 ATM connection. This table is created and used for ATM AAL5 trunking applications only.
.1.3.6.1.4.1.9.9.351.1.6.1This table contains the statistical information on a per AAL5 connection basis for ATM AAL5 Trunking applications.
.1.3.6.1.4.1.9.9.351The MIB for voice and Nx64 over ATM Trunking applications. The following lists the abbreviations used in this MIB: AAL ATM Adaption Layer AIS Alarm Indication Signal CID Channel Identifier DSP Digital Signal Processing DTMF Dual Tone Multi Frequency FCS Frame Check Sequence TDM Time Division Multiplexing PVC Permanent Virtual Circuit RAI Remote Alarm Indication RDI Remote Defect Indication SID Silence Insertion Descriptor SVC Switched Virtual Circuit VAD Voice Activity Detection VBD Voice Band Data VC Virtual Circuit
.1.3.6.1.4.1.9.9.351.1.1.1.1An entry in the catmtCidTable. Each entry represents an AAL2 trunking connection which is uniquely identified by the PVC index and the CID number. An AAL2 trunking connection is established by binding one or more DS0 channels from a single DS1 interface to an AAL2 ATM connection identified by the CID. The Channel IDentification (CID) is the standard term used to identify an ATM AAL2 connection (ITU-T I.366.2). CID is unique within a VC, either a PVC or SVC connection.
.1.3.6.1.4.1.9.9.351.1.1.1.1.1This object is the VPI value of an ATM PVC connection.
.1.3.6.1.4.1.9.9.351.1.1.1.1.2This object is the VCI value of an ATM PVC connection.
.1.3.6.1.4.1.9.9.351.1.1.1.1.3This object is the CID of an ATM AAL2 connection, it is unique within a PVC or SVC connection. The CID number at both sides of an AAL2 connection must be the same. Value of 0 is not used, and values of 1 to 7 are reserved for layer management by ITU-T I.366.2 standard.
.1.3.6.1.4.1.9.9.351.1.1.1.1.4The value of this object equals to the 'ifIndex' of the DS1 interface. This object is mandatory when adding a CID entry. Once a CID entry is added, this object can not be modified.
.1.3.6.1.4.1.9.9.351.1.1.1.1.5An arbitrary index that uniquely identifies a DS0 group which contains one or more DS0(s) within a DS1 interface specified by 'catmtCidDs1'. This object is mandatory when adding a CID entry. Once a CID entry is added, this object can not be modified.
.1.3.6.1.4.1.9.9.351.1.1.1.1.6This object specifies the type of the AAL2 CODEC profile. The combination of the profile type and profile number specified by 'catmtCidProfileNumber' defines an AAL2 CODEC profile. This parameter is mandatory for adding and a voice trunking CID entry. This object is applicable when catmtCidNx64Enable is is set to 'false'. It is used for voice trunking applications only.
.1.3.6.1.4.1.9.9.351.1.1.1.1.7This object specifies the AAL2 CODEC profile number. The combination of profile type and profile number defines an AAL2 CODEC profile. A profile contains one or more entries, with each entry specifying an encoding algorithm and information regarding how the TDM data is to be packed into a packet. This parameter is mandatory for adding a voice trunking CID entry. This object is applicable when catmtCidNx64Enable is is set to 'false'. It is used for voice trunking applications only.
.1.3.6.1.4.1.9.9.351.1.1.1.1.8This object specifies the CODEC type used for the AAL2 trunking connection. The following table lists the CODEC types specified in each profile table by ITU I.366.2 standard. Profile Profile Packet type Number CODEC SID time(ms) ITU 1 G.711u No SID 5 G.711a No SID 5 ITU 2 G.711u SIDG 5 G.711a SIDG 5 ITU 3 G.711u SIDG 5 G.711a SIDG 5 G726-40 SIDG 5 G726-32 SIDG 5 G726-24 SIDG 5 G726-16 SIDG 5 ITU 7 G.711u SIDG 5 G.711a SIDG 5 G.729ab SID729 10 G.729a No SID 10 ITU 8 G.711u No SID 5 G.711a No SID 5 G.726-32 No SID 5 G.729ab SID729 10 G.729a SID729 10 Custom 100 G.711u SIDG 5 G.711a SIDG 5 G.726-32 SIGD 10 Custom 101 G.711u No SID 5 G.711a No SID 5 G.726-32 No SID 10 G.729ab SID729 10 G.729a No SID 10 Custom 110 G.711u SIDG 5 G.711a SIDG 5 G.726-32 SIDG 10 G.729ab SID729 30 G.729a No SID 30 Custom 200 clearChan No SID 5 This object can only be set to the CODECs defined by the profile specified by catmtCidProfileType and catmtCidProfileNumber. This object is applicable when catmtCidNx64Enable is is set to 'false'. It is used for voice trunking applications only. This object is mandatory when adding a voice trunking CID entry.
.1.3.6.1.4.1.9.9.351.1.1.1.1.9This object specifies the CODEC type to be used for Voice Band Data (VBD) upspeed. Upspeed is to change the transmission rate of a voice interface to a higher rate of CODEC type for fax/modem transportation. This object is applicable when catmtCidNx64Enable is is set to 'false'. It is used for voice trunking applications only. This object is mandatory when adding a voice trunking CID entry.
.1.3.6.1.4.1.9.9.351.1.1.1.1.10This object specifies whether a CID entry is in the Nx64 packet stream mode. When this object is set to 'false', the CID connection is for voice trunking applications only; when it is set to 'true', the CID connection is for data trunking using Nx64 packet stream (N>=1). This object can not be modified.
.1.3.6.1.4.1.9.9.351.1.1.1.1.11This object specifies the Nx64 data profile for an AAL2 data trunking connection. The value of this object is a valid index of the cdapNx64ProfileTable in the CISCO-DATA-AALX-PROFILE-MIB. This object is only applicable when catmtCidNx64Enable is set to 'true'.
.1.3.6.1.4.1.9.9.351.1.1.1.1.12This object is used to indicate the state of the CID. All bits setting to 0 which means status 'okay'.
.1.3.6.1.4.1.9.9.351.1.1.1.1.13This object is used to repeatedly apply the writable objects of catmtCidTable specified in the same SNMP PDU starting from the row defined by the index object for the number of rows specified by this object. The repetition operation works differently for data trunking and voice trunking applications. When catmtCidNx64Enable is set to 'false' (voice trunking), it is iterated through the value of DS0's and CID number. When catmtCidNx64Enable is set to 'true' (data trunking), the order of repetition operation is iterated through the value of DS1 index and CID number. (1) For voice trunking applications: At each iteration, the value of CID (catmtCid), DS0 (catmtCidDs0GroupIndex) and DS1(catmtCidDs1) will be incremented. When the value of catmtCidDs0GroupIndex reaches its maximum, catmtCidDs1 will be incremented to the next logical order of DS1 interface. (2) For data trunking applications: At each iteration, the value of catmtCid, catmtCidDs1 will be incremented. In other words, the Nx64 packet stream repetition iterates on the DS1, with each DS1 interface having the same DS0 group (catmtCidDs0GroupIndex) configuration. The repetition iteration will stop once the value of catmtCid reaches its maximum value 255 or when the next CID is not available or already configured for different type of trunking application. For example, a non-Nx64 repetition will stop if the next CID has been configured for Nx64 packet stream trunking, and vise versa. The repetition will also stop if the next contiguous DS0 group index is not available. The maximum value of this object is 248 which is the maximum number of CID or AAL2 connections allowed within a VC connection.
.1.3.6.1.4.1.9.9.351.1.1.1.1.14This object is used for error reporting of the bulk provisioning operation specified by catmtCidRepetition. The value of this object is set by the SNMP manager with its own identifier at the time of setting catmtCidRepetition to issue the bulk provisioning operation. Later on, the SNMP manager checks the value of this object. If it matches its own name, the value of catmtCidRepetitionResult will be set to indicate the result of bulk operation initiated by this SNMP manager.
.1.3.6.1.4.1.9.9.351.1.1.1.1.15This object indicates the result of the bulk provisioning specified in catmtCidRepetition. The format might look at (but not limited to): 'COMPLETION=<number of rows completed before any error occurred>/<number of rows was designated>, ERROR=<error code>/<index where the error occurred>: <error text>' For example: 'COMPLETION=22/100,ERROR=38/44:Invalid DS1 line coding for the line type'
More MIBs from Cisco
Browse all CiscoMIBs →The CISCO-UNIFIED-COMPUTING-COMPUTE-MIB provides SNMP-based monitoring and management of Cisco UCS compute blades, servers, and chassis components, exposing critical metrics such as CPU utilization, memory usage, thermal sensor readings, power supply status, and interface operational states. This module enables granular visibility into the health and performance of the Cisco Unified Computing System's compute subsystems for capacity planning and fault isolation.
The CISCO-UNIFIED-COMPUTING-STORAGE-MIB facilitates SNMP-based monitoring and management of storage subsystems, including Fibre Channel and iSCSI interfaces, within the Cisco Unified Computing System (UCS) fabric interconnects and blade servers. It exposes critical operational metrics such as port status, error counters, throughput statistics, and storage controller health states to enable granular visibility into the storage infrastructure.
The CISCO-UNIFIED-COMPUTING-VNIC-MIB enables SNMP-based monitoring and management of Virtual Network Interface Card (vNIC) attributes, including operational status, traffic counters, and binding configurations, within the Cisco Unified Computing System (UCS) fabric interconnects and server blades.
SNMP MIB module
The CISCO-UNIFIED-COMPUTING-BIOS-MIB enables SNMP-based monitoring and configuration of BIOS-level parameters, firmware versions, and hardware initialization states within Cisco Unified Computing System (UCS) servers. It provides visibility into critical server boot diagnostics, BIOS settings, and hardware readiness indicators to facilitate low-level infrastructure management and troubleshooting.
The CISCO-UNIFIED-COMPUTING-ETHER-MIB provides SNMP management interfaces for monitoring Ethernet interface statistics, link states, and error counters on Cisco Unified Computing System (UCS) fabric interconnects and blade server line cards. This module enables the tracking of physical layer connectivity, port throughput, and packet error rates within the UCS Ethernet switching infrastructure.