CISCO-VOICE-AALX-PROFILE-MIB
AI MIB Summary
The CISCO-VOICE-AALX-PROFILE-MIB manages Cisco voice gateway configurations for Voice over ATM and Voice over IP, specifically monitoring AAL1/AAL5 codec negotiation parameters, AAL2 profile definitions, and Switched Virtual Circuit (SVC) connection states.
This MIB defines the objects specific to voice over ATM or voice over IP. Those objects are related to the following areas:
1. CODEC Negotiation (AAL1/AAL5)
2. AAL2 Profile
3. SVC connection.
Main OID:
ciscoVoiceAalxProfileMIB.1.3.6.1.4.1.9.9.323
82
Objects
Active
Status
6
Dependencies
Imported Objects
Objects
82 total| Object Name |
|---|
ciscoVoiceAalxProfileMIBThis MIB defines the objects specific to voice
over ATM or voice over IP. Those objects are
related to the following areas:
1. CODEC Negotiation (AAL1/AAL5)
2. AAL2 Profile
3. SVC connection. MODULE-IDENTITY .1.3.6.1.4.1.9.9.323 |
ciscoVoiceAalxProfileMIBNotifs OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.323.0 |
ciscoVoiceAalxProfileMIBObjects OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.323.1 |
cvapCodecConfig OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.323.1.1 |
cvapCodecTableThis table defines attributes of CODEC negotiation.
These attributes are used for CODEC negotiation of a call
when a call setup request is made by call agent to the
media gateway.
One entry for AAL1 and one entry for AAL5 are created when
a new media gateway is detected by media gateway application.
All entries are deleted when the media gateway is removed
from the system. SEQUENCE OF CvapCodecEntry .1.3.6.1.4.1.9.9.323.1.1.1 |
cvapCodecEntryAn entry containing management information for CODEC
negotiation of the adaptation type for a call in the
media gateway. CvapCodecEntry .1.3.6.1.4.1.9.9.323.1.1.1.1 |
cvapCodecNegotiationAdaptTypeThis object specifies the adaptation layer which
supports CODEC negotiation of calls and the order of
CODECs used in negotiation can be configured as
the value of cvapCodecNegotiationOption.
The adaptation types include:
aal5 :VoIP with AAL5 as adaptation layer.
aal1 :VoATM with AAL1 as adaptation layer. Enumeration .1.3.6.1.4.1.9.9.323.1.1.1.1.1 |
cvapCodecNegotiationOptionThis object defines the CODEC negotiation option which
determines the order of CODECs used by a call during CODEC
negotiation.
The possible CODEC negotiation options are as follows:
Lco - local connection options
(from local call agent)
Rcd - remote connection description
(from remote gateway)
Lcl - local CODEC list which is defined in the table,
cvapCodecNegotiationTable.
If the value of this object is lcoRcdLcl(1), then
effectively the preferences are:
1. the first priority is to the local connection options
sent by the local call agent
2. the second priority is to the remote connection
description sent by the remote gateway (or related
call agent)
3. the last priority is to the local CODEC list stored
in local gateway
If the value of this object is lcoLclRcd(2), then
effectively the preferences are:
1. the first priority is to the local connection options
sent by the local call agent
2. the second priority is to the local CODEC list stored
in local gateway.
3. the last priority is to the remote connection
description sent by the remote gateway (or related call
agent)
If the value of this object is rcdLcoLcl(3), then
effectively the preferences are:
1. the first priority is to the remote connection
description sent by the remote gateway (or related
call agent)
2. the second priority is to the local connection options
sent by the local call agent
3. the last priority is to the local CODEC list stored
in local gateway
If the value of this object is rcdLclLco(4), then
effectively the preferences are:
1. the first priority is to the remote connection
description sent by the remote gateway (or related
call agent)
2. the second priority is to the local CODEC list stored
in local gateway
3. the last priority is to the local connection options
sent by the local call agent
If the value of this object is lclLcoRcd(5), then
effectively the preferences are:
1. the first priority is to the local CODEC list stored
in local gateway
2. the second priority is to the local connection options
sent by the local call agent
3. the last priority is to the remote connection
description sent by the remote gateway (or related call
agent)
If the value of this object is lclRcdLco(6), then
effectively the preferences are:
1. the first priority is to the local CODEC list stored
in local gateway
2. the second priority is to the remote connection
description sent by the remote gateway (or related
call agent)
3. the last priority is to the local connection options
sent by the local call agent.rw Enumeration .1.3.6.1.4.1.9.9.323.1.1.1.1.2 |
cvapCodecConfigTableThis table contains the attributes whose configuration
depends on CODEC types and adaptation types.
For each adaptation layer, one entry for each CODEC rate
supported by the media gateway is created by the system at
power-up. SEQUENCE OF CvapCodecConfigEntry .1.3.6.1.4.1.9.9.323.1.1.2 |
cvapCodecConfigEntryAn entry represents a CODEC rate supported for VoIP or
VoATM with different adaptation layers in the media gateway. CvapCodecConfigEntry .1.3.6.1.4.1.9.9.323.1.1.2.1 |
cvapCodecConfigAdaptTypeAn unique index identifying the adaptation layer
supported by voice applications in the media gateway.
The adaptation types include:
other :Voice over other media.
aal5 :VoIP with AAL5 as adaptation layer.
aal1 :VoATM with AAL1 as adaptation layer.
aal2 :VoATM with AAL2 as adaptation layer. Enumeration .1.3.6.1.4.1.9.9.323.1.1.2.1.1 |
cvapCodecConfigTypeThis object specifies the CODEC rate defined in
CvcSpeechCoderRate. CvcSpeechCoderRate (CISCO-VOICE-COMMON-DIAL-CONTROL-MIB) .1.3.6.1.4.1.9.9.323.1.1.2.1.2 |
cvapCodecConfigPreferenceThis object specified the preference configured by the
user for each CODEC. Lower the number, higher the
preference of the CODEC.
If this object is set to 0, the corresponding CODEC will
not be used in CODEC negotiation or in CODEC choose command.
For CODECs having the same preference, the entry with the
lower value of cvapCodecConfigType has higher precedence.rw Unsigned32 .1.3.6.1.4.1.9.9.323.1.1.2.1.3 |
cvapCodecConfigVoicePacketPeriodThis object specifies the packetization period for a
particular CODEC in voice application.
The packetization period represents the time for the
media gateway to collect the data from TDM side before
it sends out the packet.
This object is not applicable if cvapCodecConfigAdaptType
is set to 'aal2(4)' since the packetization period for
a CODEC in VoATM with AAL2 depends on the associated
profile.rw CiscoCodecPacketPeriod UNITS "microseconds" .1.3.6.1.4.1.9.9.323.1.1.2.1.4 |
cvapCodecConfigVbdPacketPeriodThis object specifies the packetization period for a
particular CODEC in VBD (Voice Band Data) upspeed.
The packetization period represents the time for the
media gateway to collect the data from TDM side before
it sends out the packet.
This object is not applicable if cvapCodecConfigAdaptType
is set to 'aal2(4)' since the packetization period for
a CODEC in VoATM with AAL2 depends on the associated
profile.rwdeprecated CiscoCodecPacketPeriod UNITS "microseconds" .1.3.6.1.4.1.9.9.323.1.1.2.1.5 |
cvapCodecConfigJitterDelayModeThe object specifies the jitter buffer mode applied to
a call connection.
adaptive - means to use cvapCodecConfigNewJtrNomDelay as
the initial jitter buffers size and let the DSP
pick the optimal value of the jitter buffer
size between the range of
cvapCodecConfigJitterMaxDelay and
cvapCodecConfigJitterMinDelay.
fixed - means to use a constant jitter buffer size
which is specified by cvapCodecConfigNewJtrNomDelay.rw CCallControlJitterDelayMode (CISCO-MEDIA-GATEWAY-MIB) .1.3.6.1.4.1.9.9.323.1.1.2.1.6 |
cvapCodecConfigJitterMaxDelayThis object specifies the maximum jitter buffer size.
If cvapCodecConfigJitterDelayMode is set to adaptive(1),
the DSP will dynamically pick an optimal value of the
jitter buffer size between the range of
cvapCodecConfigJitterMaxDelay and
cvapCodecConfigJitterMinDelay.
If cvapCodecConfigJitterDelayMode is set to fixed(2),
this object is ignored.
The value of cvapCodecConfigJitterMaxDelay needs to be
greater than or equal to the value of
cvapCodecConfigNewJtrNomDelay.rw Unsigned32 .1.3.6.1.4.1.9.9.323.1.1.2.1.7 |
cvapCodecConfigJitterNomDelayThis object specifies the nominal jitter buffer size.
If cvapCodecConfigJitterDelayMode is set to fixed(2),
the jitter buffer is fixed at this value for
the duration of the call.
if cvapCodecConfigJitterDelayMode is set to adaptive(1),
the jitter buffer is initially set to this value.
The value of cvapCodecConfigJitterNomDelay needs to be
greater than or equal to the value of
cvapCodecConfigJitterMinDelay and be smaller than or equal
to the value of cvapCodecConfigJitterMaxDelay.rwdeprecated Unsigned32 .1.3.6.1.4.1.9.9.323.1.1.2.1.8 |
cvapCodecConfigJitterMinDelayThis object specifies the minimum jitter buffer size.
If cvapCodecConfigJitterDelayMode is set to adaptive(1),
the DSP will dynamically pick an optimal value of the
jitter buffer size between the range of
cvapCodecConfigJitterMaxDelay and
cvapCodecConfigJitterMinDelay.
If cvapCodecConfigJitterDelayMode is set to fixed(2),
this object is ignored.
The value of cvapCodecConfigJitterMinDelay needs to be
smaller than or equal to the value of
cvapCodecConfigNewJtrNomDelay.rw Unsigned32 .1.3.6.1.4.1.9.9.323.1.1.2.1.9 |
cvapCodecConfigDtmfRelayWhen this object is set to 'true', the digits will be
sent as peer-to-peer packet in the bearer.
When this object is set to 'false', the digits will be
sent as regular voice packets in the bearer.
For low complexity CODECS (such as G.711), the preferred
value for this object could be 'false'.
For high complexity CODECS (such as G.729A), the preferred
value for this object should be 'true', otherwise
the digits may not get recognized properly at the remote
end.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.323.1.1.2.1.10 |
cvapCodecConfigPayloadTypeThis object specifies the payload type of the CODEC in
voice application as specified in RFC1890.
The values (0..95) are static payload type.
The values (96..127) are dynamic payload type and it is
specified dynamically through the control protocol during
call setup.
If more than one CODEC have the same payload type,
the CODEC with the highest preference (the lowest value of
cvapCodecConfigPreference) will be selected.rw Unsigned32 .1.3.6.1.4.1.9.9.323.1.1.2.1.11 |
cvapCodecConfigNewJtrNomDelayThis object specifies the nominal jitter buffer size.
If cvapCodecConfigJitterDelayMode is set to fixed(2),
the jitter buffer is fixed at this value for
the duration of the call.
if cvapCodecConfigJitterDelayMode is set to adaptive(1),
the jitter buffer is initially set to this value.
The value of cvapCodecConfigNewJtrNomDelay needs to be
greater than or equal to the value of
cvapCodecConfigJitterMinDelay and be smaller than or equal
to the value of cvapCodecConfigJitterMaxDelay.rw Unsigned32 .1.3.6.1.4.1.9.9.323.1.1.2.1.12 |
cvapAal2Config OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.323.1.2 |
cvapSvcConfig OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.323.1.3 |
cvapSvcConfigTableThis table contains the SVC (both in AAL1 and AAL2)
configuration which is used for call connection establishment
between the PNNI controller and the media gateway. SEQUENCE OF CvapSvcConfigEntry .1.3.6.1.4.1.9.9.323.1.3.1 |
cvapSvcConfigEntryAn entry containing management information for SVC connection
in the media gateway.
An entry of this table is created when a new media gateway is
detected by media gateway application.
The entry is deleted when the media gateway is removed from
the system. CvapSvcConfigEntry .1.3.6.1.4.1.9.9.323.1.3.1.1 |
cvapSvcAtmQosCellDelayThis object identifies end-to-end cell delay
in voice SVC establishment.
It is used to guarantee the quality of the route selected
for a voice SVC.
It is applicable to both AAL1 and AAL2 SVC connection
establishment.
This object is part of the extended quality of services
information element which is sent out during SVC setup.rw Integer32 .1.3.6.1.4.1.9.9.323.1.3.1.1.1 |
cvapSvcAtmQosCtdThis object identifies end-to-end maximum cell transfer
in voice SVC establishment.
It is used to guarantee the quality of the route
selected for a voice SVC.
It is applicable to both AAL1 and AAL2 SVC connection
establishment.
This value is sent in voice SVC setup
messages in end-to-end transit delay information element
as the object value.rw Integer32 .1.3.6.1.4.1.9.9.323.1.3.1.1.2 |
cvapSvcAtmQosClrThis object identifies maximum Cell Loss Ratio (CLR)
in voice SVC establishment.
It is used to guarantee the quality of the route selected
for a voice SVC.
It is applicable to both AAL1 and AAL2 SVC connection
establishment.
This value is sent in voice SVC setup messages in
extended quality of services information element as
maximum cell loss ratio value.rw Integer32 .1.3.6.1.4.1.9.9.323.1.3.1.1.3 |
cvapSvcTrfScalingFactorThis object specifies Traffic Scaling Factor
in computing factored bandwidth which is used in ATM
signaling in voice SVC establishment.
When this value is less than 100 it can be referred as a
`discount factor' and when more than 100 referred as an
`excess factor.
This object is applicable only to VBR SVC connection
establishment.
The traffic scaling is not applicable to AAL2 SVC calls
that require G.711 and clear channel CODECs.rw Integer32 .1.3.6.1.4.1.9.9.323.1.3.1.1.4 |
cvapSvcAal2CidNumberThis object specifies the default AAL2 CID (Channel
Identification) number used for AAL2 SVC connections.
0-7 is reserved.rw Integer32 .1.3.6.1.4.1.9.9.323.1.3.1.1.5 |
cvapSvcAggTrafficClippingThis object defines the aggregate traffic clipping policy.
This object specifies if the aggregate traffic clipping
policy is applicable to all bearer traffic generated in the
media gateway.
The applicable options are:
'true' - aggregate traffic clipping is enabled, local gateway
traffic management performs aggregate traffic clipping.
'false' - aggregate traffic clipping is disabled, local
gateway traffic management does not perform aggregate
traffic clipping.
This is applicable to only AAL2 SVC voice bearer traffic.
When aggregate traffic clipping is enabled, local gateway
can discard cells which are exceeding local gateway aggregate
SVC bandwidth.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.323.1.3.1.1.6 |
cvapSvcAggLinkStateThis object provides the state of the SVC link between PNNI
controller and the media gateway.
When the SVC software module fails to register NSAP address
with the PNNI controller via SAPI (Service Access Point
Interface), this object will be set to 'down', when it
is successful, this object will be set to 'up'.
if down
SVC calls cannot be made on gateway
if up
SVC calls can be made on gatewayro Enumeration .1.3.6.1.4.1.9.9.323.1.3.1.1.7 |
cvapSvcPartialFillSupportedThis object indicates the fill level of cells in case of
AAL1 adaptation .
The value of this object will be used if the call agent does
not specify partial fill in the MGCP commands (i.e if
L(local connection option):pf( partial fill) is absent).
ATM cell size is 53 bytes, 5 bytes for header, 48 bytes
for data. If the data are not enough to fill 48 bytes of one
ATM cell, the system can fill in the value of this object to
the padding bytes.rw Integer32 .1.3.6.1.4.1.9.9.323.1.3.1.1.8 |
cvapSvcMgcpSelectorByteValueThis object specifies the selector byte value of the NSAP
address for MGCP protocol.
When a SVC call setup indication from the network is received,
it will look at this object to determine the owner application
for this setup.
The value of this object can not be modified when ATM SVC
calls are up.
The value of this objects can not equal to the value of
'cvapSvcH248SelectorByteValue'.rw Integer32 .1.3.6.1.4.1.9.9.323.1.3.1.1.9 |
cvapSvcH248SelectorByteValueThis object specifies the selector byte value of the NSAP
address for H.248 protocol.
When a SVC call setup indication from the network is received,
it will look at this object to determine the owner application
for this setup.
The value of this object can not be modified when ATM SVC
calls are up.
The value of this objects can not equal to the value of
'cvapSvcMgcpSelectorByteValue'.rw Integer32 .1.3.6.1.4.1.9.9.323.1.3.1.1.10 |
cvapSvcDelNotifGuardTimerA timer, for a duration as specified by this object,
will be started when the SVC call is released from the
network side. Upon expiration of this timer, the call
agent is notified about this through ServiceChange
message(for H.248 protocol) or through gateway initiated
delete message(for MGCP protocol).
This object is not applicable for Multi-CID SVC(if MIB object
'cvapSvcMultiCIDPerSvc' is set to 'true').rw Integer32 .1.3.6.1.4.1.9.9.323.1.3.1.1.11 |
cvapSvcMultiCIDPerSvcThis object enables the user to disable or enable the
Multi-CID SVC feature on the gateway.
When this object is set to 'true', multiple CIDs can be
established on a single SVC. When this object is set to
'false', only one CID per SVC can be established.
This object cannot be modified when active SVC calls exist
on the gateway.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.323.1.3.1.1.12 |
cvapSvcMultiCIDFillTimerThis object defines the time (millisecs) to wait for filling
up the cell when the next packet is not ready. After waiting
for the time configured in this object, the cell will be sent
out.
This object is applicable only for aal2 adaptations.
Any new programmed value will not affect SVCs already
in progress.rw Unsigned32 .1.3.6.1.4.1.9.9.323.1.3.1.1.13 |
cvapSvcMultiCIDCACSCRThis object specifies the SCR (Sustained Cell Rate) per
Multi-CID SVC.
The value of this object will be used for CAC (Call Admission
Control) processing, and will determine if a new Multi-Cid SVC
needs to be created for a new incoming CID, or whether there
is room to add the new CID on the Multi-CID SVC.rw Unsigned32 .1.3.6.1.4.1.9.9.323.1.3.1.1.14 |
cvapSvcMultiCIDCACPCRThis object specifies the PCR (Peak Cell Rate) per Multi-CID
SVC.
The value of this object will be used for CAC (Call Admission
Control) processing, and will determine whether an upspeed
request can be accepted or not on the Multi-CID SVC.
The 'cvapSvcMultiCIDCACPCR' must be greater than or equal to
'cvapSvcMultiCIDCACSCR'.rw Unsigned32 .1.3.6.1.4.1.9.9.323.1.3.1.1.15 |
cvapSvcMultiCIDOriginatDelTimerThis object specifies the time to wait to delete an Originated
-SVC in the case where a CID delete just occurred and the SVC
has no more CIDs after the deletion.
The interval of this object should be 5.
The 'cvapSvcMultiCIDOriginatDelTimer' must be greater than
or equal to 'cvapSvcMultiCIDTerminatDelTimer+5', except for
the case that 'cvapSvcMultiCIDOriginatDelTimer' is 0 and
'cvapSvcMultiCIDTerminatDelTimer' is 0 (which means that the
Delete Timer feature is disabled).rw Unsigned32 .1.3.6.1.4.1.9.9.323.1.3.1.1.16 |
cvapSvcMultiCIDTerminatDelTimerThis object specifies the time that the Terminating end can
attempt to add a new CID into the Terminated-SVC after the
last CID in a slave-end SVC is deleted.
The interval of this object should be 5.
The 'cvapSvcMultiCIDOriginatDelTimer' must be greater than
or equal to 'cvapSvcMultiCIDTerminatDelTimer+5', except for
the case that 'cvapSvcMultiCIDOriginatDelTimer' is 0 and
'cvapSvcMultiCIDTerminatDelTimer' is 0 (which means that the
Delete Timer feature is disabled).rw Unsigned32 .1.3.6.1.4.1.9.9.323.1.3.1.1.17 |
cvapSvcMultiCIDGlareThresholdThis object specifies the threshold at when reached
on the SVC-Terminating end, that no more CID's can
be added to that Terminated-SVC from the Termination
end. The Originating end will be able to use the
remaining CID's in the SVC.rw Unsigned32 .1.3.6.1.4.1.9.9.323.1.3.1.1.18 |
cvapSvcStats OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.323.1.4 |
cvapSvcStatsTableThis table contains SVC statistics associated with
the communication between the media gateway and the PNNI
controller. SEQUENCE OF CvapSvcStatsEntry .1.3.6.1.4.1.9.9.323.1.4.1 |
cvapSvcStatsEntryAn entry containing statistics information for a SVC
that is associated with the communication between the
media gateway and the PNNI controller. CvapSvcStatsEntry .1.3.6.1.4.1.9.9.323.1.4.1.1 |
cvapSvcTxSetupsThis object indicates the number of 'SETUP' messages
sent to the PNNI controller from the media gateway
since last gateway reset.ro Counter32 .1.3.6.1.4.1.9.9.323.1.4.1.1.1 |
cvapSvcRxSetupsThis object indicates the number of 'SETUP' messages
received by the media gateway from the PNNI
controller since last gateway reset.ro Counter32 .1.3.6.1.4.1.9.9.323.1.4.1.1.2 |
cvapSvcTxCallProcsThis object indicates the number of call 'PROCEED' messages
sent to the PNNI controller from the media gateway
since last gateway reset.ro Counter32 .1.3.6.1.4.1.9.9.323.1.4.1.1.3 |
cvapSvcRxCallProcsThis object indicates the number of call 'PROCEED' messages
received by the media gateway from the PNNI controller
since last gateway reset.ro Counter32 .1.3.6.1.4.1.9.9.323.1.4.1.1.4 |
cvapSvcTxConnsThis object indicates the number of 'CONNECT' messages
sent to the PNNI controller from the media gateway
since last gateway reset.ro Counter32 .1.3.6.1.4.1.9.9.323.1.4.1.1.5 |
cvapSvcTxConnAcksThis object indicates the number of 'CONNECT ACK' messages
sent to the PNNI controller from the media gateway
since last gateway reset.ro Counter32 .1.3.6.1.4.1.9.9.323.1.4.1.1.6 |
cvapSvcRxConnsThis object indicates the number of 'CONNECT' messages
received by the media gateway from the PNNI controller
since last gateway reset.ro Counter32 .1.3.6.1.4.1.9.9.323.1.4.1.1.7 |
cvapSvcRxConnAcksThis object indicates the number of 'CONNECT ACK' messages
received by the gateway from the PNNI controller
since last gateway reset.ro Counter32 .1.3.6.1.4.1.9.9.323.1.4.1.1.8 |
cvapSvcTxReleasesThis object indicates the number of 'RELEASE' messages
sent to the PNNI controller from the media gateway
since last gateway reset.ro Counter32 .1.3.6.1.4.1.9.9.323.1.4.1.1.9 |
cvapSvcTxReleaseComplsThis object indicates the number of 'RELEASE COMPLETE'
messages sent to the PNNI controller from the media
gateway since last gateway reset.ro Counter32 .1.3.6.1.4.1.9.9.323.1.4.1.1.10 |
cvapSvcRxReleasesThis object indicates the number of RELEASE' messages
received by the media gateway from the PNNI controller
since last gateway reset.ro Counter32 .1.3.6.1.4.1.9.9.323.1.4.1.1.11 |
cvapSvcRxReleaseComplsThis object indicates the number of 'RELEASE COMPLETE'
messages received by the media gateway from the
PNNI controller since last gateway reset.ro Counter32 .1.3.6.1.4.1.9.9.323.1.4.1.1.12 |
cvapSvcTxRestartsThis object indicates the number of 'RESTART' messages
sent to the PNNI controller from the media gateway
since last gateway reset.ro Counter32 .1.3.6.1.4.1.9.9.323.1.4.1.1.13 |
cvapSvcTxRestartAcksThis object indicates the number of 'RESTART ACK'
messages sent to the PNNI controller from the
media gateway since last gateway reset.ro Counter32 .1.3.6.1.4.1.9.9.323.1.4.1.1.14 |
cvapSvcRxRestartsThis object indicates the number of 'RESTART' messages
received by the media gateway from the PNNI controller
since last gateway reset.ro Counter32 .1.3.6.1.4.1.9.9.323.1.4.1.1.15 |
cvapSvcRxRestartAcksThis object indicates the number of 'RESTART ACK' messages
received by the media gateway from the PNNI controller
since last gateway reset.ro Counter32 .1.3.6.1.4.1.9.9.323.1.4.1.1.16 |
cvapSvcTxResyncStrtsThis object indicates the number of 'RESYNC START' messages
sent to the PNNI controller from the media gateway
since last gateway reset.ro Counter32 .1.3.6.1.4.1.9.9.323.1.4.1.1.17 |
cvapSvcTxResyncStrtAcksThis object indicates the number of 'RESYNC START ACK'
messages sent to the PNNI controller from the
media gateway since last gateway reset.ro Counter32 .1.3.6.1.4.1.9.9.323.1.4.1.1.18 |
cvapSvcRxResyncStrtsThis object indicates the number of 'RESYNC START' messages
received by the media gateway from the PNNI controller
since last gateway reset.ro Counter32 .1.3.6.1.4.1.9.9.323.1.4.1.1.19 |
cvapSvcRxResyncStrtAcksThis object indicates the number of 'RESYNC START ACK'
messages received by the media gateway from the PNNI
controller since last gateway reset.ro Counter32 .1.3.6.1.4.1.9.9.323.1.4.1.1.20 |
cvapSvcTxResyncEndsThis object indicates the number of 'RESYNC END' messages
sent to the PNNI controller from the media gateway
since last gateway reset.ro Counter32 .1.3.6.1.4.1.9.9.323.1.4.1.1.21 |
cvapSvcTxResyncEndAcksThis object indicates the number of 'RESYNC END ACK'
messages sent to the PNNI controller from the
media gateway since last gateway reset.ro Counter32 .1.3.6.1.4.1.9.9.323.1.4.1.1.22 |
cvapSvcRxResyncEndsThis object indicates the number of 'RESYNC END ACK'
messages received by the media gateway from the
PNNI controller since last gateway reset.ro Counter32 .1.3.6.1.4.1.9.9.323.1.4.1.1.23 |
cvapSvcRxResyncEndAcksThis object indicates the number of 'RESYNC END ACK'
messages received by the media gateway from the
PNNI controller since last gateway reset.ro Counter32 .1.3.6.1.4.1.9.9.323.1.4.1.1.24 |
cvapSvcTxBulkResyncsThis object indicates the number of 'BULK RESYNC' messages
sent to the PNNI controller from the media gateway
since last gateway reset.ro Counter32 .1.3.6.1.4.1.9.9.323.1.4.1.1.25 |
cvapSvcRxBulkResyncsThis object indicates the number of 'BULK RESYNC' messages
received by the gateway from the PNNI controller
since last gateway reset.ro Counter32 .1.3.6.1.4.1.9.9.323.1.4.1.1.26 |
cvapSvcCallProcExpiriesThis object indicates the number of call 'PROCEED' messages
have been sent from the media gateway and have never received
any response from the PNNI controller.ro Counter32 .1.3.6.1.4.1.9.9.323.1.4.1.1.27 |
cvapSvcReleasExpiriesThis object indicates the number of call 'RELEASE' messages
have been sent from the media gateway and have never received
any response from the PNNI controller.ro Counter32 .1.3.6.1.4.1.9.9.323.1.4.1.1.28 |
cvapSvcConnExpiriesThis object indicates the number of call 'CONNECT' messages
have been sent from the media gateway and have never received
any response from the PNNI controller.ro Counter32 .1.3.6.1.4.1.9.9.323.1.4.1.1.29 |
cvapSvcConnAckExpiriesThis object indicates the number of call 'CONNECT ACK'
messages have been sent from the media gateway and have
never received any response from the PNNI controller.ro Counter32 .1.3.6.1.4.1.9.9.323.1.4.1.1.30 |
cvapSvcRestartExpiriesThis object indicates the number of call 'RESTART' messages
have been sent from the media gateway and have never received
any response from the PNNI controller.ro Counter32 .1.3.6.1.4.1.9.9.323.1.4.1.1.31 |
cvapSvcResyncExpiriesThis object indicates the number of call 'RESYNC START'
messages have been sent from the media gateway and have
never received any response from the PNNI controller.ro Counter32 .1.3.6.1.4.1.9.9.323.1.4.1.1.32 |
cvaProfileMIBConformance OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.323.2 |
cvaProfileMIBCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.323.2.1 |
cvaProfileMIBGroups OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.323.2.2 |