CISCO-VOICE-COMMON-DIAL-CONTROL-MIB
The CISCO-VOICE-COMMON-DIAL-CONTROL-MIB provides standardized management objects for monitoring and configuring voice call control parameters, including codec negotiation (AMR-NB, iLBC, iSAC) and dial plan logic, across Cisco voice gateways supporting VoIP, VoATM, and VoFR encapsulations.
Imported Objects
Objects
27 total| Object Name |
|---|
ciscoVoiceCommonDialControlMIBThis MIB module contains voice related objects that
are common across more than one network
encapsulation i.e VoIP, VoATM and VoFR.
*** ABBREVIATIONS, ACRONYMS AND SYMBOLS ***
GSM - Global System for Mobile Communication
AMR-NB - Adaptive Multi Rate - Narrow Band
iLBC - internet Low Bitrate Codec
iSAC - internet Speech Audio Codec MODULE-IDENTITY .1.3.6.1.4.1.9.10.55 |
cvCommonDcMIBObjects OBJECT IDENTIFIER .1.3.6.1.4.1.9.10.55.1 |
cvCommonDcCallActive OBJECT IDENTIFIER .1.3.6.1.4.1.9.10.55.1.1 |
cvCommonDcCallActiveTableThis table is a common extension to the call active
table of IETF Dial Control MIB. It contains common call
leg information about a network call leg. SEQUENCE OF CvCommonDcCallActiveEntry .1.3.6.1.4.1.9.10.55.1.1.1 |
cvCommonDcCallActiveEntryThe common information regarding a single network call
leg. The call leg entry is identified by using the same
index objects that are used by Call Active table of IETF
Dial Control MIB to identify the call.
An entry of this table is created when its associated
call active entry in the IETF Dial Control MIB is created
and the call active entry contains information for the
call establishment to a network dialpeer.
The entry is deleted when its associated call active entry
in the IETF Dial Control MIB is deleted. CvCommonDcCallActiveEntry .1.3.6.1.4.1.9.10.55.1.1.1.1 |
cvCommonDcCallActiveConnectionIdThe global call identifier for the network call.ro CvcGUid .1.3.6.1.4.1.9.10.55.1.1.1.1.1 |
cvCommonDcCallActiveVADEnableThe object indicates whether or not the VAD (Voice
Activity Detection) is enabled for the voice call.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.10.55.1.1.1.1.2 |
cvCommonDcCallActiveCoderTypeRateThe negotiated coder rate. It specifies the transmit
rate of voice/fax compression to its associated call leg
for the call.
This rate is different from the configuration rate
because of rate negotiation during the call.ro CvcCoderTypeRate .1.3.6.1.4.1.9.10.55.1.1.1.1.3 |
cvCommonDcCallActiveCodecBytesSpecifies the payload size of the voice packet.ro INTEGER .1.3.6.1.4.1.9.10.55.1.1.1.1.4 |
cvCommonDcCallActiveInBandSignalingSpecifies the type of in-band signaling being used on
the call. This object is instantiated only for
Connection Trunk calls.ro CvcInBandSignaling .1.3.6.1.4.1.9.10.55.1.1.1.1.5 |
cvCommonDcCallActiveCallingNameThe calling party name this call is connected to. If the
name is not available, then it will have a length of zero.ro SnmpAdminString .1.3.6.1.4.1.9.10.55.1.1.1.1.6 |
cvCommonDcCallActiveCallerIDBlockThe object indicates whether or not the caller ID feature
is blocked for this voice call.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.10.55.1.1.1.1.7 |
cvCommonDcCallHistory OBJECT IDENTIFIER .1.3.6.1.4.1.9.10.55.1.2 |
cvCommonDcCallHistoryTableThis table is the Common extension to the call history
table of IETF Dial Control MIB. It contains Common call
leg information about a network call leg. SEQUENCE OF CvCommonDcCallHistoryEntry .1.3.6.1.4.1.9.10.55.1.2.1 |
cvCommonDcCallHistoryEntryThe common information regarding a single network call
leg. The call leg entry is identified by using the same
index objects that are used by Call Active table of IETF
Dial Control MIB to identify the call.
An entry of this table is created when its associated
call history entry in the IETF Dial Control MIB is
created and the call history entry contains information
for the call establishment to a network dialpeer.
The entry is deleted when its associated call history
entry in the IETF Dial Control MIB is deleted. CvCommonDcCallHistoryEntry .1.3.6.1.4.1.9.10.55.1.2.1.1 |
cvCommonDcCallHistoryConnectionIdThe global call identifier for the gateway call.ro CvcGUid .1.3.6.1.4.1.9.10.55.1.2.1.1.1 |
cvCommonDcCallHistoryVADEnableThe object indicates whether or not the VAD (Voice
Activity Detection) was enabled for the voice call.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.10.55.1.2.1.1.2 |
cvCommonDcCallHistoryCoderTypeRateThe negotiated coder rate. It specifies the transmit rate
of voice/fax compression to its associated call leg for
the call.
This rate is different from the configuration rate
because of rate negotiation during the call.ro CvcCoderTypeRate .1.3.6.1.4.1.9.10.55.1.2.1.1.3 |
cvCommonDcCallHistoryCodecBytesSpecifies the payload size of the voice packet.ro INTEGER .1.3.6.1.4.1.9.10.55.1.2.1.1.4 |
cvCommonDcCallHistoryInBandSignalingSpecifies the type of in-band signaling used on the
call. This object is instantiated only for
Connection Trunk calls.ro CvcInBandSignaling .1.3.6.1.4.1.9.10.55.1.2.1.1.5 |
cvCommonDcCallHistoryCallingNameThe calling party name this call is connected to. If
the name is not available, then it will have a length
of zero.ro SnmpAdminString .1.3.6.1.4.1.9.10.55.1.2.1.1.6 |
cvCommonDcCallHistoryCallerIDBlockThe object indicates whether or not the caller ID
feature is blocked for this voice call.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.10.55.1.2.1.1.7 |
cvCommonDcMIBNotificationPrefix OBJECT IDENTIFIER .1.3.6.1.4.1.9.10.55.2 |
cvCommonDcMIBNotifications OBJECT IDENTIFIER .1.3.6.1.4.1.9.10.55.2.0 |
cvCommonDcMIBConformance OBJECT IDENTIFIER .1.3.6.1.4.1.9.10.55.3 |
cvCommonDcMIBCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.9.10.55.3.1 |
cvCommonDcMIBGroups OBJECT IDENTIFIER .1.3.6.1.4.1.9.10.55.3.2 |
More MIBs from Cisco
Browse all CiscoMIBs →The CISCO-ENTITY-VENDORTYPE-OID-MIB maps Cisco-specific hardware component identifiers to the ENTITY-MIB's entPhysicalTable, enabling precise differentiation of physical device types such as line cards, power supplies, and fans within Cisco infrastructure. This mapping ensures that SNMP management systems can accurately correlate physical inventory entries with vendor-specific component definitions for accurate device discovery and monitoring.
The CISCO-UNIFIED-COMPUTING-EQUIPMENT-MIB provides SNMP-based monitoring and management of Cisco Unified Computing System (UCS) hardware components, including chassis, blades, fabric interconnects, and power supplies. It exposes critical operational metrics such as device status, port states, temperature readings, fan speeds, and power consumption data for infrastructure health assessment.
The CISCO-UNIFIED-COMPUTING-ADAPTOR-MIB enables SNMP-based monitoring and management of physical and virtual network adapter interfaces, including link status, traffic counters, error statistics, and port configuration parameters, within the Cisco Unified Computing System (UCS) fabric interconnects and blade servers.
The CISCO-UNIFIED-COMPUTING-TC-MIB module defines standard textual conventions and data type definitions required for monitoring Cisco Unified Computing System (UCS) hardware components, including server blades, fabric interconnects, and chassis resources. These definitions enable consistent interpretation of specific UCS metrics such as power supply status, fan speeds, thermal readings, and port utilization across SNMP management applications.
The CISCO-UNIFIED-COMPUTING-FABRIC-MIB enables SNMP-based monitoring and management of the Cisco UCS Fabric Interconnects and associated fabric switching infrastructure, exposing metrics for port states, link utilization, error counters, and fabric topology status. It facilitates granular visibility into the physical and logical fabric layers, including uplink/downlink interfaces, VLAN configurations, and fabric failover conditions within the unified computing environment.
The STARENT-MIB module provides SNMP management and monitoring capabilities for Cisco ASR 5000 and ASR 5500 multimedia core platforms, specifically exposing metrics related to 2G/3G/4G and WiFi subscriber sessions, inline service states, and carrier-class high-availability status.