BayNetworks-IISIS-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for BayNetworks-IISIS-MIB.
78
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
78 total| Object Name |
|---|
wfIisisGeneralGroup OBJECT IDENTIFIER .1.3.6.1.4.1.18.3.5.3.2.8.1 |
RFC1155-SMI Unknown .1.3.6.1.4.1.18.3.5.3.2.8.1 |
wfIisisGeneralDelete'This value determines whether I-ISIS is configured'rw Enumeration .1.3.6.1.4.1.18.3.5.3.2.8.1.1 |
wfIisisGeneralDisable'The administrative status of I-ISIS in the router. The
value 'enabled' denotes that the I-ISIS Process is active
on at least one interface; 'disabled' disables it on
all interfaces.'rw Enumeration .1.3.6.1.4.1.18.3.5.3.2.8.1.2 |
wfIisisGeneralState'The state of I-ISIS'ro Enumeration .1.3.6.1.4.1.18.3.5.3.2.8.1.3 |
wfIisisRouterIdThis value contains the system ID of this Intermediate System.rw OCTET STRING .1.3.6.1.4.1.18.3.5.3.2.8.1.4 |
wfIisisVersionThis read-only parameter identifies the version number of the
IS-IS protocol to which this node conforms to.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.18.3.5.3.2.8.1.5 |
wfIisisRouterTypeThis value determines whether this system is L1 only router
L2 only router or L1-L2 IS.rw Enumeration .1.3.6.1.4.1.18.3.5.3.2.8.1.6 |
wfIisisSpfHoldDownHold Down Timer for the SPF (in seconds). The SPF will
run at most once per hold down timer value. A value of 0
means no hold down.rw INTEGER .1.3.6.1.4.1.18.3.5.3.2.8.1.7 |
wfIisisPrimaryLogMaskA parameter to specify which I-ISIS log messages should be logged.
This will only effect the Primary I-ISIS gate.
Each bit represents a message as defined below. A 1 in that
bit location means to log it and a 0 means not to put that
log message in the log. Changing this value will NOT restart
I-ISIS, but will take effct immediately(if there are any messages
to be logged.
bit 31 bit 0
+
| |
+
bit0 Trace Messages
bit1 INFO Level messages
bit2 debug level messages
bit3 I-ISIS interface state change messages
bit4 Nbr state changes
bit5 self-origination of LSA's
bit6 receipt of new LSA's
bit7 changes to I-ISIS`s Routing Table
bit8 Bad LS requests, Ack's, or updates
bit9 receipt of less recent LSA's
bit10 receipt of more recent self-originated LSA's
bit11 receipt of MAxAge LSA's (i.e. LSA's being flushed)
bit12 - 31 reservedrw Gauge .1.3.6.1.4.1.18.3.5.3.2.8.1.8 |
wfIisisMaximumPathMaximum number of equal cost paths allowed for a network installed
by OSPF.rw INTEGER .1.3.6.1.4.1.18.3.5.3.2.8.1.9 |
wfIisisMaxAreasThis value defines the maximum allowable number of areas addresses
for the domain that this router exists in.rw INTEGER .1.3.6.1.4.1.18.3.5.3.2.8.1.10 |
wfIisisNumL1LspsNumber of L2 LSPS stored in the databasero Gauge .1.3.6.1.4.1.18.3.5.3.2.8.1.11 |
wfIisisNumL2LspsNumber of L2 LSPS stored in the databasero Gauge .1.3.6.1.4.1.18.3.5.3.2.8.1.12 |
wfIisisCksumIsPdusThis value indicates whether ISIS PDUs will carry a checksum.rw Enumeration .1.3.6.1.4.1.18.3.5.3.2.8.1.13 |
wfIisisL1LspPasswordThis assigns a password such that only L1 Lsps with the matching
password will be accepted. All L1 Lsps generated
by this system will contain this string in the password option.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.18.3.5.3.2.8.1.14 |
wfIisisL2LspPasswordThis assigns a password such that only L2 Lsps with the matching
password will be accepted. All L2 Lsps generated
by this system will contain this string in the password option.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.18.3.5.3.2.8.1.15 |
wfIisisAreaAddrThis Assigns the area address for this router.
This field must be filled in.
If the user doesn't enter a value, then assign 0x470005.
Site Manager must force the user to enter at least a 3-byte
value for this field.rw OCTET STRING .1.3.6.1.4.1.18.3.5.3.2.8.1.16 |
wfIisisAreaAddrAlias1This Assigns the first area address alias for this router.
This field does no have to be filled in, but if the user
tries to enter a value, Site Manager must make sure that
it is at least 3-bytes in length.rw OCTET STRING .1.3.6.1.4.1.18.3.5.3.2.8.1.17 |
wfIisisAreaAddrAlias2This Assigns the second area address alias for this router.
This field does no have to be filled in, but if the user
tries to enter a value, Site Manager must make sure that
it is at least 3-bytes in length.rw OCTET STRING .1.3.6.1.4.1.18.3.5.3.2.8.1.18 |
wfIisisL1CorruptedLspsNumber of Corrupted L1-Lsps Detected.ro Counter .1.3.6.1.4.1.18.3.5.3.2.8.1.19 |
wfIisisL2CorruptedLspsNumber of Corrupted L2-Lsps Detected.ro Counter .1.3.6.1.4.1.18.3.5.3.2.8.1.20 |
wfIisisL1LspDbOverLoadsNumber of times the L1 Lsp Database Overload event has been
generated.ro Counter .1.3.6.1.4.1.18.3.5.3.2.8.1.21 |
wfIisisL2LspDbOverLoadsNumber of times the L2Lsp Database Overload event has been
generated.ro Counter .1.3.6.1.4.1.18.3.5.3.2.8.1.22 |
wfIisisNearestL2IsThis is the ID of the nearest L2 system in this area.ro OCTET STRING .1.3.6.1.4.1.18.3.5.3.2.8.1.23 |
wfIisisNumL1RoutesNumber of L1 Routes.ro Gauge .1.3.6.1.4.1.18.3.5.3.2.8.1.24 |
wfIisisNumL2RoutesNumber of L2 Routes.ro Gauge .1.3.6.1.4.1.18.3.5.3.2.8.1.25 |
wfIisisMinLSPGenerationIntervalMin time interval(in secs) before LSP generationrw INTEGER .1.3.6.1.4.1.18.3.5.3.2.8.1.26 |
wfIisisMaxLSPGenerationIntervalMax time interval(in secs) before LSP generationrw INTEGER .1.3.6.1.4.1.18.3.5.3.2.8.1.27 |
wfIisisMaxAgeThe lifetime of the lsp after which it will be considered expiredrw INTEGER .1.3.6.1.4.1.18.3.5.3.2.8.1.28 |
wfIisisMinLSPXmtIntervalrw INTEGER .1.3.6.1.4.1.18.3.5.3.2.8.1.29 |
wfIisisPartialSNPIntervalrw INTEGER .1.3.6.1.4.1.18.3.5.3.2.8.1.30 |
wfIisisZeroAgeLifetimeIf the remaining lifetime of an LSP reaches zero, the
expired LSP will be kept in the database for this time (in
seconds)rw INTEGER .1.3.6.1.4.1.18.3.5.3.2.8.1.31 |
wfIisisAgePendThe number of entries processed before this gate pendsrw INTEGER .1.3.6.1.4.1.18.3.5.3.2.8.1.32 |
wfIisisCsnpBuildIntervalThe interval at which CSNPs are generated by the Designated ISrw INTEGER .1.3.6.1.4.1.18.3.5.3.2.8.1.33 |
wfIisisL2LspBufferSizeThe max size of the LSP generated by systemrw INTEGER .1.3.6.1.4.1.18.3.5.3.2.8.1.34 |
wfIisisL1SpfCntThe number of times the L1 I-ISIS SPF algorithm
has been run for this area.ro Counter .1.3.6.1.4.1.18.3.5.3.2.8.1.35 |
wfIisisL2SpfCntThe number of times the L2 I-ISIS SPF algorithm
has been run for this area.ro Counter .1.3.6.1.4.1.18.3.5.3.2.8.1.36 |
wfIisisAreaTable'Information describing the configured parameters and
cumulative statistics of the router's attached areas.'
REFERENCE
'I-ISIS Version 2, Section 6 The Area Data Structure' SEQUENCE OF WfIisisAreaEntry .1.3.6.1.4.1.18.3.5.3.2.8.2 |
wfIisisAreaEntry'Information describing the configured parameters and
cumulative statistics of one of the router's attached
areas.' WfIisisAreaEntry .1.3.6.1.4.1.18.3.5.3.2.8.2.1 |
wfIisisAreaDeleteThis value determines if the I-ISIS router is configured with
this area.rw Enumeration .1.3.6.1.4.1.18.3.5.3.2.8.2.1.1 |
wfIisisAreaDisableThis value indicates the state of this area on the I-ISIS
router.rw Enumeration .1.3.6.1.4.1.18.3.5.3.2.8.2.1.2 |
wfIisisAreaStateThis value indicates the state of the I-ISIS Area.ro Enumeration .1.3.6.1.4.1.18.3.5.3.2.8.2.1.3 |
wfIisisAreaIdA 32-bit integer uniquely identifying an area. Area
ID 0.0.0.0 is used for the I-ISIS backbone.ro IpAddress .1.3.6.1.4.1.18.3.5.3.2.8.2.1.4 |
wfIisisSpfCntThe number of times the I-ISIS SPF algorithm
has been run for this area.ro Counter .1.3.6.1.4.1.18.3.5.3.2.8.2.1.5 |
wfIisisL1LspHdrTable2 u_int32's so the inst_id len is 2. SEQUENCE OF WfIisisL1LspHdrEntry .1.3.6.1.4.1.18.3.5.3.2.8.3 |
wfIisisL1LspHdrEntryA Record in the Level 1 Lsp Header Table WfIisisL1LspHdrEntry .1.3.6.1.4.1.18.3.5.3.2.8.3.1 |
wfIisisL1LspHdrLspIdLSPID = Source ID + Pseudo-node ID + LSP numberro OCTET STRING .1.3.6.1.4.1.18.3.5.3.2.8.3.1.1 |
wfIisisL1LspHdrLifetimeLsp Lifetimero INTEGER .1.3.6.1.4.1.18.3.5.3.2.8.3.1.2 |
wfIisisL1LspHdrSeqnumLsp sequence numberro INTEGER .1.3.6.1.4.1.18.3.5.3.2.8.3.1.3 |
wfIisisL1LspHdrFlagsFlags: P/ATT/LSPDBOL/IS typero INTEGER .1.3.6.1.4.1.18.3.5.3.2.8.3.1.4 |
wfIisisL1LspHdrCksumChecksumro OCTET STRING .1.3.6.1.4.1.18.3.5.3.2.8.3.1.5 |
wfIisisL2LspHdrTable2 u_int32's so the inst_id len is 2. SEQUENCE OF WfIisisL2LspHdrEntry .1.3.6.1.4.1.18.3.5.3.2.8.4 |
wfIisisL2LspHdrEntryA Record in the Lsp Header Table WfIisisL2LspHdrEntry .1.3.6.1.4.1.18.3.5.3.2.8.4.1 |
wfIisisL2LspHdrLspIdLSPID = Source ID + Pseudo-node ID + LSP numberro OCTET STRING .1.3.6.1.4.1.18.3.5.3.2.8.4.1.1 |
wfIisisL2LspHdrLifetimeLsp Lifetimero INTEGER .1.3.6.1.4.1.18.3.5.3.2.8.4.1.2 |
wfIisisL2LspHdrSeqnumLsp sequence numberro INTEGER .1.3.6.1.4.1.18.3.5.3.2.8.4.1.3 |
wfIisisL2LspHdrFlagsFlags: P/ATT/LSPDBOL/IS typero INTEGER .1.3.6.1.4.1.18.3.5.3.2.8.4.1.4 |
wfIisisL2LspHdrCksumChecksumro OCTET STRING .1.3.6.1.4.1.18.3.5.3.2.8.4.1.5 |
wfIisisIfTable'The I-ISIS Interface Table describes the interfaces from
the viewpoint of I-ISIS.' SEQUENCE OF WfIisisIfEntry .1.3.6.1.4.1.18.3.5.3.2.8.5 |
wfIisisIfEntry'The I-ISIS Interface Entry describes one interface from
the viewpoint of I-ISIS.' WfIisisIfEntry .1.3.6.1.4.1.18.3.5.3.2.8.5.1 |
wfIisisIfDeleteThis variable determines in an I-ISIS Interface has been
configured on the router.rw Enumeration .1.3.6.1.4.1.18.3.5.3.2.8.5.1.1 |
wfIisisIfDisable'The I-ISIS interface's administrative status. The value
'enabled' denotes that neighbor relationships may be
formed on the interface, and the interface will be
advertised as an internal route to some area. The
value 'disabled' denotes that the interface is external
to I-ISIS.'rw Enumeration .1.3.6.1.4.1.18.3.5.3.2.8.5.1.2 |
wfIisisIfIpAddress'The IP address of this I-ISIS interface.'ro IpAddress .1.3.6.1.4.1.18.3.5.3.2.8.5.1.3 |
wfIisisAddressLessIf'For the purpose of easing the instancing of addressed
and addressless interfaces; This variable takes the
value 0 on interfaces with IP Addresses, and the
corresponding value of ifIndex for interfaces having no
IP Address.'ro INTEGER .1.3.6.1.4.1.18.3.5.3.2.8.5.1.4 |
wfIisisIfRouterLevelThis is the level protocol that the circuit runs.
Its a bit mask to allow for some combination of
L1, L2, External, ES-IS-only.rw Enumeration .1.3.6.1.4.1.18.3.5.3.2.8.5.1.5 |
wfIisisIfL1DefaultMetricThis is the default cost of using this circuit for L1 traffic.rw INTEGER .1.3.6.1.4.1.18.3.5.3.2.8.5.1.6 |
wfIisisIfL2DefaultMetricThis is the default cost of using this circuit for L2 traffic.rw INTEGER .1.3.6.1.4.1.18.3.5.3.2.8.5.1.7 |
wfIisisIfL1DrPriorityThis is the priority for this system to become L1 designated
router on this LAN circuit.rw INTEGER .1.3.6.1.4.1.18.3.5.3.2.8.5.1.8 |
wfIisisIfL2DrPriorityThis is the priority for this system to become L2 designated
router on this LAN circuit.rw INTEGER .1.3.6.1.4.1.18.3.5.3.2.8.5.1.9 |
wfIisisIfHelloTimerThis is the period (secs) between IIH hello transmissions.rw INTEGER .1.3.6.1.4.1.18.3.5.3.2.8.5.1.10 |
wfIisisIfPasswordThis is Circuit Password for this circuit. Used to filter
out Hellos from systems without the correct password.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.18.3.5.3.2.8.5.1.11 |
wfIisisIfHelloMtuSizeConfigure Hello MTU size per I-ISIS interface
This parameter has the following values/meanings:
1 - Use the MTU specified by IP
2 - Use the MTU of ethernet, regardless of what IP
says
> 2 - Use this value as the actual MTU.
If the value is smaller than what I-ISIS needs as
a minimum then the mtu specified by IP is used.
For example, 3 would never be used as an MTU.rw INTEGER .1.3.6.1.4.1.18.3.5.3.2.8.5.1.12 |
wfIisisIfIihHoldMultiplierThis is the multiplier value used to compute the hold time
set in the IIH PDUs transmitted from this router. Hold time
equals IIH Timer times IIH Hold Multiplier.rw INTEGER .1.3.6.1.4.1.18.3.5.3.2.8.5.1.13 |
wfIisisIfIshHoldMultiplierThis is the multiplier value used to compute the hold time
set in the ISH PDUs transmitted from this router. Hold time
equals IIH Timer times IIH Hold Multiplier.rw INTEGER .1.3.6.1.4.1.18.3.5.3.2.8.5.1.14 |
wfIisisIfTypeThe IISIS interface type.rw Enumeration .1.3.6.1.4.1.18.3.5.3.2.8.5.1.15 |
wfIisisIfCsnpTimerThis is the period (in seconds) between CSNP transmissions.rw INTEGER .1.3.6.1.4.1.18.3.5.3.2.8.5.1.16 |
wfIisisIfStatsTable::= { wfIisisGroup 6 }
wfIisisIfStatsEntry OBJECT-TYPE
SYNTAX WfIisisIfStatsEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION SEQUENCE OF WfIisisIfStatsEntry .wfIisisDynNbrEntry.12 |