BCSSIMULCRYPTSCS-MIB
The Simulcrypt SCS MIB module for Motorola BCS products.
Main OID:
bcsSimulcryptScs.1.3.6.1.4.1.1166.7.7
52
Objects
Active
Status
3
Dependencies
Imported Objects
Objects
52 total| Object Name |
|---|
bcsSimulcryptScsThe Simulcrypt SCS MIB module for Motorola BCS products. MODULE-IDENTITY .1.3.6.1.4.1.1166.7.7 |
bcsSimScsConfig OBJECT IDENTIFIER .1.3.6.1.4.1.1166.7.7.1 |
bcsSimScsConfigGeneral OBJECT IDENTIFIER .1.3.6.1.4.1.1166.7.7.1.1 |
bcsSimScsNetworkIdThis parameter specifies the network ID used for this Simulcrypt system. The network ID is a Simulcrypt system parameter, please see Simulcrypt system specifications for a more detailed explanation. SEM Note: Once written, a save must be performed via the semSaveConfig parameter and the SEM must be rebooted for the change to take effect.rw Unsigned32 .1.3.6.1.4.1.1166.7.7.1.1.1 |
bcsSimScsMaxNetworkDelayWorst case propagation delay, in milliseconds, introduced by network topology. Will be factored into negotiations of the actual Simulcrypt crypto-period. SEM Note: Once written, a save must be performed via the semSaveConfig parameter and the SEM must be rebooted for the change to take effect.rw Unsigned32 .1.3.6.1.4.1.1166.7.7.1.1.2 |
bcsSimScsNominalCryptoPeriodThis value specifies the nominal crypto-period in seconds. This value is used as a target for this device during crypto- period negotiations. The actual negotiated crypto-period may be equal to or greater than this value. SEM Note: Once written, a save must be performed via the semSaveConfig parameter and the SEM must be rebooted for the change to take effect.rw Unsigned32 .1.3.6.1.4.1.1166.7.7.1.1.3 |
bcsSimScsAccessCriteriaSourceThis value specifies which vendor will provide the access criteria information. SEM Note: Once written, a save must be performed via the semSaveConfig parameter and the SEM must be rebooted for the change to take effect.rw Enumeration .1.3.6.1.4.1.1166.7.7.1.1.4 |
bcsSimScsEcmgTimeoutThis parameter specifies how long the SCS should wait for a response from the ECMG. This value is specified in seconds. SEM Note: Once written, a save must be performed via the semSaveConfig parameter and the SEM must be rebooted for the change to take effect.rw Unsigned32 .1.3.6.1.4.1.1166.7.7.1.1.5 |
bcsSimScsEcmIdInitialEach ECM ID and Super CAS ID combination in the Simulcrypt system must be globally unique. To simplify configuration, each SCS is given a starting ECM ID to assign to the first ECM stream it creates. The number is incremented as new ECM streams are created. Each SCS must be configured with a different value. The initial values should be spaced sufficiently to prevent overlapping. Recommended spacing is 128. SEM Note: Once written, a save must be performed via the semSaveConfig parameter and the SEM must be rebooted for the change to take effect.rw Unsigned32 .1.3.6.1.4.1.1166.7.7.1.1.6 |
bcsSimScsEcmChannelTestPeriodicityPeriodicity for the channel test procedure.Default set to 20sec. @Range(min=1, max=3600) @Config(config=yes, reboot=no) @Save(semSaveConfig, value=2, default=yes) @File(config.ini, type='ini')rw Unsigned32 .1.3.6.1.4.1.1166.7.7.1.1.7 |
bcsSimScsEcmNetworkDelayThe network delay value to account for delays while waiting on an ECM response.Default set to 500msec. @Range(min=0, max=30000) @Config(config=yes, reboot=no) @Save(semSaveConfig, value=2, default=yes) @File(config.ini, type='ini')rw Unsigned32 .1.3.6.1.4.1.1166.7.7.1.1.8 |
bcsSimScsEcmReplyTimeoutTime to wait before timing out while waiting on a response to a channel/stream management message (i.e.: channel_setup, channel_test, stream_setup).Default set to 4000 msec. @Range(min=100, max=60000) @Config(config=yes, reboot=no) @Save(semSaveConfig, value=2, default=yes) @File(config.ini, type='ini')rw Unsigned32 .1.3.6.1.4.1.1166.7.7.1.1.9 |
bcsSimScsEcmgConnectionTableThis table persists the Simulcrypt SCS to ECMG connections or channels. The device will send Simulcrypt control words to a maximum of bcsSimScsMaxEcmg. SEQUENCE OF BcsSimScsEcmgConnectionEntry .1.3.6.1.4.1.1166.7.7.1.2 |
bcsSimScsEcmgConnectionEntryA single entry in the bcsSimScsEcmgConnectionTable table. BcsSimScsEcmgConnectionEntry .1.3.6.1.4.1.1166.7.7.1.2.1 |
bcsSimScsEcmgConnectIndexThe Simulcrypt ECMG Connection table index. Integer32 .1.3.6.1.4.1.1166.7.7.1.2.1.1 |
bcsSimScsEcmgConnectEnabledEach row in the bcsSimScsEcmgConnectionTable represents a potential SCS<=>ECMG connection that will be attempted during simulcrypt SCS initialization. This setting controls whether or not the attempt is made. This setting has two legal settings: disabled (1) <= The connection will be attempted. enabled (2) <= The connection will not be attempted. Once written, a save must be performed via the semSaveConfig parameter and the SEM must be rebooted for the change to take effect.rw EnableDisableTYPE .1.3.6.1.4.1.1166.7.7.1.2.1.2 |
bcsSimScsEcmgConnectSuperCasIdThe Super CAS ID of the ECMG that will be connected to by the Simulcrypt SCS. The Super CAS ID is the 32 bit concatenation of the CAS ID and the Sub CAS ID. The CAS ID identifies the Conditional Access provider. It supplies the upper 16 bits of the SuperCAS ID. The Sub CAS ID identifies instances of a provider's ECMGs on the Simulcrypt network. It supplies the lower 16 bits of the Super CAS ID. Each ECM ID and SuperCAS ID combination in the Simulcrypt system must be globally unique. SEM Note: Once written, a save must be performed via the semSaveConfig parameter and the SEM must be rebooted for the change to take effect.rw Unsigned32 .1.3.6.1.4.1.1166.7.7.1.2.1.3 |
bcsSimScsEcmgConnectIpAddrThe IP address that the ECMG is listening on. Used to open a socket between the SCS and the ECMG. SEM Note: Once written, a save must be performed via the semSaveConfig parameter and the SEM must be rebooted for the change to take effect.rw IpAddress .1.3.6.1.4.1.1166.7.7.1.2.1.4 |
bcsSimScsEcmgConnectPortThe remote port that the ECMG is listening on. Used to open a socket between the SCS and the ECMG. SEM Note: Once written, a save must be performed via the semSaveConfig parameter and the SEM must be rebooted for the change to take effect.rw Integer32 .1.3.6.1.4.1.1166.7.7.1.2.1.5 |
bcsSimScsEcmgRedundancyConfigTableThis table configures parameters associated with the ECMG redudancy feature. @Commit(param=bcsSimScsEcmgRedundancyConfigApplyChange, value=2) @Save(semSaveConfig, value=2) @File(config.ini, type='ini') SEQUENCE OF BcsSimScsEcmgRedundancyConfigEntry .1.3.6.1.4.1.1166.7.7.1.3 |
bcsSimScsEcmgRedundancyConfigEntryA single entry in bcsSimScsEcmgRedundancyConfigTable. BcsSimScsEcmgRedundancyConfigEntry .1.3.6.1.4.1.1166.7.7.1.3.1 |
bcsSimScsEcmgRedundancyConfigIndexIndex into the table. Integer32 .1.3.6.1.4.1.1166.7.7.1.3.1.1 |
bcsSimScsEcmgRedundancyConfigAutoSwitchBackIf enabled (2), programs (which were taken away earlier from this ECMG upon its failure) will be automatically switched back to this ECMG after its recovery. If disabled (1), such an automatic switching will not happen. Detailed semantics are captured in requirements.Default value is enabled.rw EnableDisableTYPE .1.3.6.1.4.1.1166.7.7.1.3.1.2 |
bcsSimScsEcmgRedundancyConfigManualSwitchBackWhen autoswitchback is enabled manual switch back is notActive.When manual switch back Button get pressed Manual switch back state get changed from manualSwitchBackNotInProgress(1) to (2)manualSwitchBack.Then the programs (which were taken away earlier from this ECMG upon its failure)will be switched back to it. Once the switchback progress get finished ,manual switch back state changed to (1) manualSwitchBackNotInProgress.rw ManualSwitchBackTYPE .1.3.6.1.4.1.1166.7.7.1.3.1.3 |
bcsSimScsEcmgRedundancyConfigMaxStreamsMaximum number of streams supported.The default value is 128. @Config(config=yes, reboot=yes)rw Integer32 .1.3.6.1.4.1.1166.7.7.1.3.1.4 |
bcsSimScsEcmgRedundancyConfigApplyTableTable of Apply Change for the data for bcsSimScsEcmgRedundancyConfigTable. A row of this table corresponds to a row in bcsSimScsEcmgRedundancyConfigTable. SEQUENCE OF BcsSimScsEcmgRedundancyConfigApplyEntry .1.3.6.1.4.1.1166.7.7.1.4 |
bcsSimScsEcmgRedundancyConfigApplyEntryECMG Redundancy Configuration Apply Table Entry. BcsSimScsEcmgRedundancyConfigApplyEntry .1.3.6.1.4.1.1166.7.7.1.4.1 |
bcsSimScsEcmgRedundancyConfigApplyIndexECMG index - also maps to the bcsSimScsEcmgRedundancyConfigTable index Integer32 .1.3.6.1.4.1.1166.7.7.1.4.1.1 |
bcsSimScsEcmgRedundancyConfigApplyChangeThe Apply for a row of data in bcsSimScsEcmgRedundancyConfigTable. A row in this table corresponds to the same row index in the bcsSimScsEcmgRedundancyConfigTable. This parameter MUST be set to 'apply' in order for any of the data in the rows to take effect in the SEM. This parameter MUST be set LAST after all other data in the configuration table rows has been configured. @Config(config=no, reboot=no)rw ApplyDataToDeviceTYPE .1.3.6.1.4.1.1166.7.7.1.4.1.2 |
bcsSimScsStatus OBJECT IDENTIFIER .1.3.6.1.4.1.1166.7.7.2 |
bcsSimScsStatusGeneral OBJECT IDENTIFIER .1.3.6.1.4.1.1166.7.7.2.1 |
bcsSimScsMibSupportStatusIndicates whether the device is capable of supporting and/or enabled to support the functionality of the bcsSimulcryptScs MIB.ro Enumeration .1.3.6.1.4.1.1166.7.7.2.1.1 |
bcsSimScsMaxEcmgThe maximum number of ECMGs this device can support.ro Unsigned32 .1.3.6.1.4.1.1166.7.7.2.1.2 |
bcsSimScsMaxProgramsThe maximum number of programs this device can support.ro Unsigned32 .1.3.6.1.4.1.1166.7.7.2.1.3 |
bcsSimScsMaxProgramEcmgThe maximum number of ECMGs that can be associated with a program in this device.ro Unsigned32 .1.3.6.1.4.1.1166.7.7.2.1.4 |
bcsSimScsEcmgRedundancyConfigInvalidApplyTextWhen bcsSimScsEcmgRedundancyConfigApplyChange is set to 'applyNotInProgressInvalidData' this entry may contain a text description of what was wrong with the data. This entry contains the description for the most recent apply of a related entry that was invalid.ro DisplayString .1.3.6.1.4.1.1166.7.7.2.1.5 |
bcsSimScsEcmgStatusTableIt contains status information for the SCS to ECMG connections. There can be up to bcsSimScsMaxEcmg active SCS to ECMG connections at a time. SEQUENCE OF BcsSimScsEcmgStatusEntry .1.3.6.1.4.1.1166.7.7.2.2 |
bcsSimScsEcmgStatusEntryA single entry in the bcsSimScsEcmgStatusTable table. BcsSimScsEcmgStatusEntry .1.3.6.1.4.1.1166.7.7.2.2.1 |
bcsSimScsEcmgStatusIndexThis index is used to traverse the bcsSimScsEcmgTable table. The index varies from 1..bcsSimScsMaxEcmg. In the event that some connections are not active this will be designated by the value of bcsSimScsEcmgChannelState. Integer32 .1.3.6.1.4.1.1166.7.7.2.2.1.1 |
bcsSimScsEcmgTcpStateThis column specifies TCP connection state of this SCS <==> ECMG connection.ro Enumeration .1.3.6.1.4.1.1166.7.7.2.2.1.2 |
bcsSimScsEcmgChannelIdThis column specifies channel ID.ro Unsigned32 .1.3.6.1.4.1.1166.7.7.2.2.1.3 |
bcsSimScsEcmgChannelStateThis column specifies ECMG channel state of this SCS <==> ECMG connection.ro Enumeration .1.3.6.1.4.1.1166.7.7.2.2.1.4 |
bcsSimScsEcmgSuperCasIdThis column specifies super CAS Id of the ECMG that the SCS is connected to on this connection.ro Unsigned32 .1.3.6.1.4.1.1166.7.7.2.2.1.5 |
bcsSimScsProgramTableIt contains status information for the SCS programs. There can be up to bcsSimScsMaxPrograms Simulcrypt programs active in the SCS at a time. Each program can be associated with up to bcsSimScsMaxProgramEcmg. SEQUENCE OF BcsSimScsProgramEntry .1.3.6.1.4.1.1166.7.7.2.3 |
bcsSimScsProgramEntryA single entry in the bcsSimScsProgramTable table. BcsSimScsProgramEntry .1.3.6.1.4.1.1166.7.7.2.3.1 |
bcsSimScsProgramIndexThis index is used to traverse the bcsSimScsProgramTable table. Limited by bcsSimScsMaxPrograms. Integer32 .1.3.6.1.4.1.1166.7.7.2.3.1.1 |
bcsSimScsProgramEcmgIndexECMG index. This index is used to traverse the bcsSimScsProgramTable table. Limited by bcsSimScsMaxProgramEcmg. Integer32 .1.3.6.1.4.1.1166.7.7.2.3.1.2 |
bcsSimScsProgramStateThis column displays the service state of this program. (1) - program configured, no event running (2) - program configured, event running normally (3) - program not configuredro Enumeration .1.3.6.1.4.1.1166.7.7.2.3.1.3 |
bcsSimScsProgramCryptoPeriodThis column displays the actual crypto-period in seconds that is in use for this program.ro Unsigned32 .1.3.6.1.4.1.1166.7.7.2.3.1.4 |
bcsSimScsProgramChannelIdThis column displays the channel ID.ro Unsigned32 .1.3.6.1.4.1.1166.7.7.2.3.1.5 |
bcsSimScsProgramEcmgSuperCasIdThis column displays the Super CAS-ID of the 1st ECMG on this service.ro Unsigned32 .1.3.6.1.4.1.1166.7.7.2.3.1.6 |
bcsSimScsProgramEcmgStreamStateThis column displays the stream state for an ECMG on this service.ro Enumeration .1.3.6.1.4.1.1166.7.7.2.3.1.7 |