WHISP-SM-MIB
This module contains MIB definitions for Subscriber Modem.
Main OID:
whispSmMibModule.1.3.6.1.4.1.161.19.1.1.13
387
Objects
Active
Status
6
Dependencies
Imported Objects
Objects
387 total| Object Name |
|---|
whispSmMibModuleThis module contains MIB definitions for Subscriber Modem. MODULE-IDENTITY .1.3.6.1.4.1.161.19.1.1.13 |
whispSmConfig OBJECT IDENTIFIER .1.3.6.1.4.1.161.19.3.2.1 |
rfScanListRF scan list string. The frequencies vary by product and region. If the list is too long an SNMP error will be returned. If this occurs please refer to OID rfScanListTable, which will allow user to enter the full range of available frequencies. Special settings: 0: none. all: All frequencies in the band(s) supported by the radio will be selected. all49, all51, all52: Available only for 450i 5 GHz wideband radio. all54, all57: Available only for 450 and 450i 5 GHz radios. When doing a set, separate values with comma with no white space between values.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.2.1.1 |
powerUpModeSM Power Up Mode With No 802.3 Link. 1 -- Power up in Aim mode 2 -- Power up in Operational mode.rw Enumeration .1.3.6.1.4.1.161.19.3.2.1.2 |
lanIpSmLAN IP.rw IpAddress .1.3.6.1.4.1.161.19.3.2.1.3 |
lanMaskSmLAN subnet mask.rw IpAddress .1.3.6.1.4.1.161.19.3.2.1.4 |
defaultGwSmDefault gateway.rw IpAddress .1.3.6.1.4.1.161.19.3.2.1.5 |
networkAccessNetwork accessibility. Public or local IP. For multipoint only.rw Enumeration .1.3.6.1.4.1.161.19.3.2.1.6 |
authKeySmAuthentication key. It should be equal or less than 32 characters long.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.2.1.7 |
enable8023linkTo enable or disable 802.3 link. For SMs only.rw Enumeration .1.3.6.1.4.1.161.19.3.2.1.8 |
authKeyOptionThis option is for SMs only. Backhaul timing slave always uses the set key. 0 - Use default key. 1 - Use set key.rw Enumeration .1.3.6.1.4.1.161.19.3.2.1.9 |
timingPulseGated0 - Disable (Always propagate the frame timing pulse). 1 - Enable (If SM out of sync then dont propagate the frame timing pulse).rw Enumeration .1.3.6.1.4.1.161.19.3.2.1.10 |
naptPrivateIPNAPT private IP address. Only the first three bytes can be changed when NAPT is enabled.rw IpAddress .1.3.6.1.4.1.161.19.3.2.1.11 |
naptPrivateSubnetMaskNAPT private subnet mask. Only the last byte can be changed when NAPT is enabled. The address will always be: 255.255.255.x.rw IpAddress .1.3.6.1.4.1.161.19.3.2.1.12 |
naptPublicIPIP Address of NAPT Public Interface. The variable is available only when NAPT is enabled.rw IpAddress .1.3.6.1.4.1.161.19.3.2.1.13 |
naptPublicSubnetMaskSubnet mask for NAPT Public Interface. The variable is available only when NAPT is enabled.rw IpAddress .1.3.6.1.4.1.161.19.3.2.1.14 |
naptPublicGatewayIPIP Address of NAPT Public Interface Gateway. The variable is available only when NAPT is enabled.rw IpAddress .1.3.6.1.4.1.161.19.3.2.1.15 |
naptRFPublicIPIP Address of RF Public Interface. The variable is available only when NAPT is enabled.rw IpAddress .1.3.6.1.4.1.161.19.3.2.1.16 |
naptRFPublicSubnetMaskSubnet mask of RF Public Interface. The variable is available only when NAPT is enabled.rw IpAddress .1.3.6.1.4.1.161.19.3.2.1.17 |
naptRFPublicGatewayIP Address of RF Public Interface Gateway. The variable is available only when NAPT is enabled.rw IpAddress .1.3.6.1.4.1.161.19.3.2.1.18 |
naptEnableTo enable or disable NAPT. For multipoint only. 1=Enable NAPT, 0=Disable NAPT.rw Enumeration .1.3.6.1.4.1.161.19.3.2.1.19 |
arpCacheTimeoutARP cache time out in unit of minutes. For multipoint only. Range from 1-30.rw INTEGER .1.3.6.1.4.1.161.19.3.2.1.20 |
tcpGarbageCollectTmoutUnits of minutes for TCP garbage collection. For multipoint only. Range 4-1440.rw INTEGER .1.3.6.1.4.1.161.19.3.2.1.21 |
udpGarbageCollectTmoutUnits of minutes for UDP garbage collection. For multipoint only. Range 1-1440.rw INTEGER .1.3.6.1.4.1.161.19.3.2.1.22 |
dhcpClientEnableTo enable or disable DHCP client. For multipoint SM's with NAPT enabled.rwobsolete Enumeration .1.3.6.1.4.1.161.19.3.2.1.23 |
dhcpServerEnableTo enable or disable DHCP server. For multipoint SM's with NAPT enabled.rw Enumeration .1.3.6.1.4.1.161.19.3.2.1.24 |
dhcpServerLeaseTimeUnits of days for DHCP server lease time. For multipoint SM's with NAPT enabled. Range from 1-30.rw INTEGER .1.3.6.1.4.1.161.19.3.2.1.25 |
dhcpIPStartThe last byte will be set for the starting IP that our DHCP server gives away. The first 3 bytes of the starting IP are the same as those of NAPT private IPrw IpAddress .1.3.6.1.4.1.161.19.3.2.1.26 |
dnsAutomaticTo have DHCP Server obtain DNS information automatically or manually.rw Enumeration .1.3.6.1.4.1.161.19.3.2.1.27 |
prefferedDNSIPThe preferred DNS IP when we are configured for static DNS (Not used when configured for automatic DNS).rw IpAddress .1.3.6.1.4.1.161.19.3.2.1.28 |
alternateDNSIPThe alternate DNS IP when we are configured for static DNS (Not used when configured for automatic DNS).rw IpAddress .1.3.6.1.4.1.161.19.3.2.1.29 |
dmzIPOnly the last byte of DMZ Host IP will be set. The first 3 bytes of DMZ IP are the same as those of NAPT private IP.rw IpAddress .1.3.6.1.4.1.161.19.3.2.1.30 |
dmzEnableTo enable or disable DMZ host functionality.rw Enumeration .1.3.6.1.4.1.161.19.3.2.1.31 |
dhcpNumIPsToLeaseNumber of IP addresses that our DHCP server can give away.rw INTEGER .1.3.6.1.4.1.161.19.3.2.1.32 |
pppoeFilterTo set PPPoE packet filter when NAT is disabled. Obsolete - Use corresponding OID in whipsBoxConfig MIB.rwobsolete Enumeration .1.3.6.1.4.1.161.19.3.2.1.33 |
smbFilterTo set SMB packet filter when NAT is disabled. Obsolete - Use corresponding OID in whipsBoxConfig MIB.rwobsolete Enumeration .1.3.6.1.4.1.161.19.3.2.1.34 |
snmpFilterTo set SNMP packet filter when NAT is disabled. Obsolete - Use corresponding OID in whipsBoxConfig MIB.rwobsolete Enumeration .1.3.6.1.4.1.161.19.3.2.1.35 |
userP1FilterTo set user defined port 1 packet filter when NAT is disabled. Obsolete - Use corresponding OID in whipsBoxConfig MIB.rwobsolete Enumeration .1.3.6.1.4.1.161.19.3.2.1.36 |
userP2FilterTo set user defined port 2 packet filter when NAT is disabled. Obsolete - Use corresponding OID in whipsBoxConfig MIB.rwobsolete Enumeration .1.3.6.1.4.1.161.19.3.2.1.37 |
userP3FilterTo set user defined port 3 packet filter when NAT is disabled. Obsolete - Use corresponding OID in whipsBoxConfig MIB.rwobsolete Enumeration .1.3.6.1.4.1.161.19.3.2.1.38 |
allOtherIpFilterTo set all other IPv4 packet filter when NAT is disabled. Obsolete - Use corresponding OID in whipsBoxConfig MIB.rwobsolete Enumeration .1.3.6.1.4.1.161.19.3.2.1.39 |
upLinkBCastFilterThis variable is currently obsolete.rwobsolete Enumeration .1.3.6.1.4.1.161.19.3.2.1.40 |
arpFilterTo set ARP packet filter when NAT is disabled. Obsolete - Use corresponding OID in whipsBoxConfig MIB.rwobsolete Enumeration .1.3.6.1.4.1.161.19.3.2.1.41 |
allOthersFilterTo set all other packet filter when NAT is disabled. Obsolete - Use corresponding OID in whipsBoxConfig MIB.rwobsolete Enumeration .1.3.6.1.4.1.161.19.3.2.1.42 |
userDefinedPort1An integer value of number one user defined port. Range:0-65535 Obsolete - Use corresponding OID in whipsBoxConfig MIB.rwobsolete INTEGER .1.3.6.1.4.1.161.19.3.2.1.43 |
port1TCPFilterTo set user defined port 1 TCP traffic filter. Obsolete - Use corresponding OID in whipsBoxConfig MIB.rwobsolete Enumeration .1.3.6.1.4.1.161.19.3.2.1.44 |
port1UDPFilterTo set user defined port 1 UDP traffic filter. Obsolete - Use corresponding OID in whipsBoxConfig MIB.rwobsolete Enumeration .1.3.6.1.4.1.161.19.3.2.1.45 |
userDefinedPort2An integer value of number two user defined port. Range:0-65535 Obsolete - Use corresponding OID in whipsBoxConfig MIB.rwobsolete INTEGER .1.3.6.1.4.1.161.19.3.2.1.46 |
port2TCPFilterTo set user defined port 2 TCP traffic filter. Obsolete - Use corresponding OID in whipsBoxConfig MIB.rwobsolete Enumeration .1.3.6.1.4.1.161.19.3.2.1.47 |
port2UDPFilterTo set user defined port 2 UDP traffic filter. Obsolete - Use corresponding OID in whipsBoxConfig MIB.rwobsolete Enumeration .1.3.6.1.4.1.161.19.3.2.1.48 |
userDefinedPort3An integer value of number three user defined port. Range:0-65535 Obsolete - Use corresponding OID in whipsBoxConfig MIB.rwobsolete INTEGER .1.3.6.1.4.1.161.19.3.2.1.49 |
port3TCPFilterTo set user defined port 3 TCP traffic filter. Obsolete - Use corresponding OID in whipsBoxConfig MIB.rwobsolete Enumeration .1.3.6.1.4.1.161.19.3.2.1.50 |
port3UDPFilterTo set user defined port 3 UDP traffic filter. Obsolete - Use corresponding OID in whipsBoxConfig MIB.rwobsolete Enumeration .1.3.6.1.4.1.161.19.3.2.1.51 |
bootpcFilterTo set bootp client sourced packets filter when NAT is disabled. Obsolete - Use corresponding OID in whipsBoxConfig MIB.rwobsolete Enumeration .1.3.6.1.4.1.161.19.3.2.1.52 |
bootpsFilterTo set bootp server sourced packets filter when NAT is disabled. Obsolete - Use corresponding OID in whipsBoxConfig MIB.rwobsolete Enumeration .1.3.6.1.4.1.161.19.3.2.1.53 |
ip4MultFilterTo set IPv4 MultiCast packets filter when NAT is disabled. Obsolete - Use corresponding OID in whipsBoxConfig MIB.rwobsolete Enumeration .1.3.6.1.4.1.161.19.3.2.1.54 |
ingressVIDUntagged ingress VID.rw INTEGER .1.3.6.1.4.1.161.19.3.2.1.55 |
lowPriorityUplinkCIRLow priority uplink CIR.rw INTEGER .1.3.6.1.4.1.161.19.3.2.1.56 |
lowPriorityDownlinkCIRLow priority downlink CIR.rw INTEGER .1.3.6.1.4.1.161.19.3.2.1.57 |
hiPriorityChannelTo enable or disable high priority channel.rw Enumeration .1.3.6.1.4.1.161.19.3.2.1.58 |
hiPriorityUplinkCIRHigh priority uplink CIR.rw INTEGER .1.3.6.1.4.1.161.19.3.2.1.59 |
hiPriorityDownlinkCIRHigh priority downlink CIR.rw INTEGER .1.3.6.1.4.1.161.19.3.2.1.60 |
smRateAdaptRate adaptation parameter. 0: no rate adaptation. 1: 1x and 2x adaptation. 2: 1x,2x and 3x adaptation.rwobsolete Enumeration .1.3.6.1.4.1.161.19.3.2.1.61 |
upLnkDataRateSustained uplink bandwidth cap.rw INTEGER .1.3.6.1.4.1.161.19.3.2.1.62 |
upLnkLimitBurst uplink bandwidth cap.rw INTEGER .1.3.6.1.4.1.161.19.3.2.1.63 |
dwnLnkDataRateSustained downlink bandwidth cap.rw INTEGER .1.3.6.1.4.1.161.19.3.2.1.64 |
dwnLnkLimitBurst downlink bandwidth cap.rw INTEGER .1.3.6.1.4.1.161.19.3.2.1.65 |
dfsConfigTo configure proper regions for Dynamic Frequency Shifting. For 5.2/5.4/5.7 GHz radios.rwobsolete Enumeration .1.3.6.1.4.1.161.19.3.2.1.66 |
ethAccessFilterEnableTo enable or disable Ethernet Port access filtering to SM Management Functions. (0) - Ethernet access to SM Management allowed. (1) - Ethernet access to SM Management blocked.rwobsolete Enumeration .1.3.6.1.4.1.161.19.3.2.1.67 |
ipAccessFilterEnableTo enable or disable IP access filtering to Management functions. (0) - IP access will be allowed from all addresses. (1) - IP access will be controlled using allowedIPAccess1-3 entries.rw Enumeration .1.3.6.1.4.1.161.19.3.2.1.68 |
allowedIPAccess1Allow access to SM Management from this IP. 0 is default setting to allow from all IPs.rw IpAddress .1.3.6.1.4.1.161.19.3.2.1.69 |
allowedIPAccess2Allow access to SM Management from this IP. 0 is default setting to allow from all IPs.rw IpAddress .1.3.6.1.4.1.161.19.3.2.1.70 |
allowedIPAccess3Allow access to SM Management from this IP. 0 is default setting to allow from all IPs.rw IpAddress .1.3.6.1.4.1.161.19.3.2.1.71 |
rfDhcpStateTo enable or disable RF Interface DHCP feature.rw Enumeration .1.3.6.1.4.1.161.19.3.2.1.72 |
bCastMIRTo enable and set Broadcast/ Multicast MIR feature. Use value of 0 to disable. Units are as per bCastMIRUnits variable. Set the units first and then set this value.rw Enumeration .1.3.6.1.4.1.161.19.3.2.1.73 |
bhsReRegAllows BHS re-registration every 24 hours. Enable allows re-registration and Disable does not. 24 Hour Encryption Refresh.rwobsolete Enumeration .1.3.6.1.4.1.161.19.3.2.1.74 |
smLEDModeFlagTo set LED Panel Operation to Revised Mode(1) or to Legacy Mode(0)rw Enumeration .1.3.6.1.4.1.161.19.3.2.1.75 |
ethAccessEnableTo enable or disable Ethernet Port access to SM Management Functions. (1) - Ethernet access to SM Management allowed. (0) - Ethernet access to SM Management blocked.rw Enumeration .1.3.6.1.4.1.161.19.3.2.1.76 |
pppoeEnableEnable or disable PPPoE on the SM. NAT MUST be enabled prior and Translation Bridging MUST be DISABLED on the AP.rw Enumeration .1.3.6.1.4.1.161.19.3.2.1.77 |
pppoeAuthenticationTypeSet the PPPoE Authentication Type to either None or CHAP/paprw Enumeration .1.3.6.1.4.1.161.19.3.2.1.78 |
pppoeAccessConcentratorSet the PPPoE Access Concentrator Name. Less than or equal to 32 charactersrw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.2.1.79 |
pppoeServiceNameSet the PPPoE Service Name. Less than or equal to 32 charactersrw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.2.1.80 |
pppoeUserNameSet the PPPoE Username. Less than or equal to 32 charactersrw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.2.1.81 |
pppoePasswordSet the PPPoE Password. Less than or equal to 32 charactersrw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.2.1.82 |
pppoeTCPMSSClampEnableEnable or disable TCP MSS Clamping. Enabling this will cause the SM to edit the TCP MSS in TCP SYN and SYN-ACK packets. This will allow for a workaround for MTU issues so that the TCP session will only go up to the clamped MSS. If you are using PMTUD reliably, this should not be needed.rw Enumeration .1.3.6.1.4.1.161.19.3.2.1.83 |
pppoeMTUOverrideEnableEnable the overriding of the PPP link's MTU. Normally, the PPP link will set the MTU to the MRU of the PPPoE Server, but this may be overridden. If the MRU of the PPPoE server is smaller than the desired MTU, the smaller MTU will be used.rw Enumeration .1.3.6.1.4.1.161.19.3.2.1.84 |
pppoeMTUOverrideValueEnable the overriding of the PPP link's MTU. Normally, the PPP link will set the MTU to the MRU of the PPPoE Server, but this may be overridden. If the MRU of the PPPoE server is smaller than the desired MTU, the smaller MTU will be used. Max MTU of a PPPoE link is 1492.rw INTEGER .1.3.6.1.4.1.161.19.3.2.1.85 |
pppoeTimerTypeSet the PPPoE Timer type. Can be a Keep Alive timer where the link will be checked periodically and automatically redialed if the link is down. Also could be an Idle Timeout where the link will be automatically dropped after an idle period and redialed if user data is present. Keep Alive timers are in seconds while Idle Timeout timers are in minutes.rw Enumeration .1.3.6.1.4.1.161.19.3.2.1.86 |
pppoeTimeoutPeriodThe Timeout Period. The use of this depends on the Timer Type. If the Timer Type is KeepAlive, then the timeout period is in seconds. If the Timer Type is Idle Timeout, then the timeout period is in minutes. Minimum values are 20 seconds for KeepAlive timer, and 5 minutes for Idle Timeout.rw INTEGER .1.3.6.1.4.1.161.19.3.2.1.87 |
timedSpectrumAnalysisDurationAs of release 13.0.2 this value is depricated. Please use the OID in whispBoxConfig. Value in seconds for a timed spectrum analysis. Range is 10-1000 seconds.rwdeprecated INTEGER .1.3.6.1.4.1.161.19.3.2.1.88 |
spectrumAnalysisOnBootTo enable or disable Spectrum Analysis on boot up for one scan through the band. (0) - Disabled (1) - Enabledrw Enumeration .1.3.6.1.4.1.161.19.3.2.1.89 |
spectrumAnalysisActionAs of release 13.0.2, this OID has been deprecated. Please use the OID in whispBoxConfig. Start or stop timed or continuous Spectrum Analysis and also give status. (0) - Stop Spectrum Analysis (1) - Start Timed Spectrum Analysis (2) - Start Continuous Spectrum Analysis (3) - Idle, no Spectrum Analysis results. (4) - Idle, Spectrum Analysis results available. (5) - Timed or Remote Spectrum Analysis in progress. (6) - Continuous Spectrum Analysis in progress. Note: Continuous mode has a max of 24 hours.rwdeprecated Enumeration .1.3.6.1.4.1.161.19.3.2.1.90 |
pppoeConnectODForce a manual PPPoE connection attempt.rw Enumeration .1.3.6.1.4.1.161.19.3.2.1.91 |
pppoeDisconnectODForce a manual PPPoE disconnection.rw Enumeration .1.3.6.1.4.1.161.19.3.2.1.92 |
smAntennaTypeDeprecated. See whispBoxStatus.antType for antenna type information.rwobsolete Enumeration .1.3.6.1.4.1.161.19.3.2.1.93 |
natConnectionTypeTo configure the SM NAT connection type. Options are Static IP, DHCP, or PPPoE.rw Enumeration .1.3.6.1.4.1.161.19.3.2.1.94 |
wanPingReplyEnableAllow Ping replies from SM WAN interface. Applies to both NAT and PPPoE WAN interfaces.rw Enumeration .1.3.6.1.4.1.161.19.3.2.1.95 |
packetFilterDirectionTo packet filter direction when NAT is disabled. Upstream is default. Obsolete - Use corresponding OID in whipsBoxConfig MIB.rwobsolete Enumeration .1.3.6.1.4.1.161.19.3.2.1.96 |
colorCode2Second Color code. The variable is deprecated. See additionalColorCode in whispSmConfig.rwdeprecated INTEGER .1.3.6.1.4.1.161.19.3.2.1.97 |
colorCodepriority2Priority setting for the second color code. The variable is deprecated. See additionalColorCodePriority in whispSmConfig.rwdeprecated Enumeration .1.3.6.1.4.1.161.19.3.2.1.98 |
colorCode3Third Color code. The variable is deprecated. See additionalColorCode in whispSmConfig.rwdeprecated INTEGER .1.3.6.1.4.1.161.19.3.2.1.99 |
colorCodepriority3Priority setting for the third color code. The variable is deprecated. See additionalColorCodePriority in whispSmConfig.rwdeprecated Enumeration .1.3.6.1.4.1.161.19.3.2.1.100 |
colorCode4Fourth Color code. The variable is deprecated. See additionalColorCode in whispSmConfig.rwdeprecated INTEGER .1.3.6.1.4.1.161.19.3.2.1.101 |
colorCodepriority4Priority setting for the fourth color code. The variable is deprecated. See additionalColorCodePriority in whispSmConfig.rwdeprecated Enumeration .1.3.6.1.4.1.161.19.3.2.1.102 |
colorCode5Fifth Color code. The variable is deprecated. See additionalColorCode in whispSmConfig.rwdeprecated INTEGER .1.3.6.1.4.1.161.19.3.2.1.103 |
colorCodepriority5Priority setting for the fifth color code. The variable is deprecated. See additionalColorCodePriority in whispSmConfig.rwdeprecated Enumeration .1.3.6.1.4.1.161.19.3.2.1.104 |
colorCode6Sixth Color code. The variable is deprecated. See additionalColorCode in whispSmConfig.rwdeprecated INTEGER .1.3.6.1.4.1.161.19.3.2.1.105 |
colorCodepriority6Priority setting for the sixth color code. The variable is deprecated. See additionalColorCodePriority in whispSmConfig.rwdeprecated Enumeration .1.3.6.1.4.1.161.19.3.2.1.106 |
colorCode7Seventh Color code. The variable is deprecated. See additionalColorCode in whispSmConfig.rwdeprecated INTEGER .1.3.6.1.4.1.161.19.3.2.1.107 |
colorCodepriority7Priority setting for the seventh color code. The variable is deprecated. See additionalColorCodePriority in whispSmConfig.rwdeprecated Enumeration .1.3.6.1.4.1.161.19.3.2.1.108 |
colorCode8Eighth Color code. The variable is deprecated. See additionalColorCode in whispSmConfig.rwdeprecated INTEGER .1.3.6.1.4.1.161.19.3.2.1.109 |
colorCodepriority8Priority setting for the eighth color code. The variable is deprecated. See additionalColorCodePriority in whispSmConfig.rwdeprecated Enumeration .1.3.6.1.4.1.161.19.3.2.1.110 |
colorCode9Ninth Color code. The variable is deprecated. See additionalColorCode in whispSmConfig.rwdeprecated INTEGER .1.3.6.1.4.1.161.19.3.2.1.111 |
colorCodepriority9Priority setting for the ninth color code. The variable is deprecated. See additionalColorCodePriority in whispSmConfig.rwdeprecated Enumeration .1.3.6.1.4.1.161.19.3.2.1.112 |
colorCode10Tenth Color code. The variable is deprecated. See additionalColorCode in whispSmConfig.rwdeprecated INTEGER .1.3.6.1.4.1.161.19.3.2.1.113 |
colorCodepriority10Priority setting for the tenth color code. The variable is deprecated. See additionalColorCodePriority in whispSmConfig.rwdeprecated Enumeration .1.3.6.1.4.1.161.19.3.2.1.114 |
natDNSProxyEnableIf enabled, the SM will advertise itself as the DNS server when it sends out DHCP client leases and forward DNS queries automatically. If disabled, the SM will forward on upstream DNS server information when it sends out DHCP client leases.rw Enumeration .1.3.6.1.4.1.161.19.3.2.1.115 |
allIpv4FilterTo set all IPv4 packet filter when NAT is disabled. Enabling this will automatically enable all of the known IP filters (SMB, SNMP, Bootp, IPv4 Mcast, User Defined Ports, and All Other IPv4). Obsolete - Use corresponding OID in whipsBoxConfig MIB.rwobsolete Enumeration .1.3.6.1.4.1.161.19.3.2.1.116 |
spectrumAnalysisDisplayThe display for Spectrum Analyzer: (0) - Averaging over entire period (1) - Instantaneous showing the last readingrw Enumeration .1.3.6.1.4.1.161.19.3.2.1.117 |
syslogSMXmitSettingObtains Syslog transmit configuration from AP/BHM if set to 0, overrides if 1 or 2. Transmits syslog data to Syslog server if enabled(1), stops if disabled (2).rwdeprecated Enumeration .1.3.6.1.4.1.161.19.3.2.1.118 |
syslogServerApPreferredUses Syslog server configuration from AP/BHM if enabled and available, otherwise uses local configuration.rw Enumeration .1.3.6.1.4.1.161.19.3.2.1.119 |
syslogMinLevelApPreferredUses Syslog minimum transmit level configuration from AP/BHM if available, otherwise uses local configuration.rw Enumeration .1.3.6.1.4.1.161.19.3.2.1.120 |
syslogSMXmitControlObtains Syslog transmit configuration from AP/BHM if available, or specifies the local transmit state.rw Enumeration .1.3.6.1.4.1.161.19.3.2.1.121 |
eapPeerAAAServerCommonNameTHIS OID IS CURRENTLY UNUSED: EAP Peer Server Common Namerw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.2.1.126 |
rfScanListBandFilterThis element is obsolete.rwobsolete Enumeration .1.3.6.1.4.1.161.19.3.2.1.127 |
upLnkMaxBurstDataRateMaximum burst uplink rate.rw INTEGER UNITS "Kilobits/sec" .1.3.6.1.4.1.161.19.3.2.1.128 |
dwnLnkMaxBurstDataRateMaximum burst downlink rate.rw INTEGER UNITS "Kilobits/sec" .1.3.6.1.4.1.161.19.3.2.1.129 |
cyclicPrefixScanCyclic Prefix value for frequency scanning used by MIMO SMs only. When setting use a comma delimited list of cyclic prefixes with no spaces. For example: 1/8,1/16rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.2.1.130 |
bandwidthScanBandwidth values for frequency scanning used by MIMO SMs only. When setting use a comma delimited list of bandwidths. For example: 10, 20rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.2.1.131 |
apSelectionThis OID affects what AP to attempt to register to when Canopy SMs scan see more than one AP that are valid in it's configuration. (0) - Default, Canopy radios after scanning select the best AP that will optimize for estimated throughput. (1) - Select the AP with the best receive power level. Note this is only if multiple APs fit the current scan configuration, and will be overriden by color codes, RADIUS, etc.rw Enumeration .1.3.6.1.4.1.161.19.3.2.1.132 |
radioBandscanConfigUsed to determine when frequency, cyclic prefix and bandwidth settings take effect for band scanning MIMO SMs. 0 - Instant 1 - Delayed 2 - Apply changesrw Enumeration .1.3.6.1.4.1.161.19.3.2.1.133 |
forcepoweradjustThis will force a multipoint SM to initiate an asynchronous power adjust sequence. This is done automatically every 2 minutes.rw INTEGER .1.3.6.1.4.1.161.19.3.2.1.134 |
clearBerrResultsThis will clear the BER results.rw INTEGER .1.3.6.1.4.1.161.19.3.2.1.135 |
berrautoupdateflagThis indicates if the once a second BERR updating of counters is enabled. 1 = enabled 0 = disabledrw INTEGER .1.3.6.1.4.1.161.19.3.2.1.136 |
testSMBER0 - Disable (Return the SM to a normal operation state). 1 - Enable (Set SM into a BER test state).rw Enumeration .1.3.6.1.4.1.161.19.3.2.1.137 |
allowedIPAccessNMLength1Length of the network mask to apply to the AllowedIPAddress when assessing if access is allowedrw INTEGER .1.3.6.1.4.1.161.19.3.2.1.138 |
allowedIPAccessNMLength2Length of the network mask to apply to the AllowedIPAddress when assessing if access is allowedrw INTEGER .1.3.6.1.4.1.161.19.3.2.1.139 |
allowedIPAccessNMLength3Length of the network mask to apply to the AllowedIPAddress when assessing if access is allowedrw INTEGER .1.3.6.1.4.1.161.19.3.2.1.140 |
naptRemoteManageTo enable or disable Remote Management. For multipoint only. 0=Disable Remote Management, 1=Enable - Standalone Config, 2=Enable - Use WAN Interface.rw Enumeration .1.3.6.1.4.1.161.19.3.2.1.141 |
spectrumAnalysisScanBandwidthScanning Bandwidth used for the Spectrum Analyzer. Only available on PMP 450.rw Enumeration .1.3.6.1.4.1.161.19.3.2.1.142 |
berDeModSelectThe BER demodulation level the SM is set. 0 for QPSK, 1 for 16-QAM, 2 for 64-QAM, and 3 for 256-QAM.rw Enumeration .1.3.6.1.4.1.161.19.3.2.1.143 |
multicastVCRcvRateMulticast VC Receive Ratero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.2.1.144 |
pmp430ApRegistrationOptionsSelects AP types (PMP 430 and/or PMP 450/450i) that are available for the PMP 430 SM. When both AP types are selected, if the SM does not register to an AP after 10 minutes, it will reboot to scan the other AP type.rw Enumeration .1.3.6.1.4.1.161.19.3.2.1.145 |
switchRadioModeAndRebootSetting this to 1 will force switch the SM to the other radio mode and immediately reboot the unit. When the unit finishes rebooting, it will be in finishedReboot state. Only will be allowed to be set if both registration options are configured. PMP 430 SM only. Introduced in release 12.2.rw Enumeration .1.3.6.1.4.1.161.19.3.2.1.146 |
natTslTableSizeNAT Translation Table Size. Range 1024-8192.rw INTEGER .1.3.6.1.4.1.161.19.3.2.1.147 |
ingressVIDPriorityingress VID VLAN Priority.rw INTEGER .1.3.6.1.4.1.161.19.3.2.1.148 |
ingressVIDPriorityModeingress VID VLAN Priority Mode.rw Enumeration .1.3.6.1.4.1.161.19.3.2.1.149 |
providerVIDPriorityProvider VID VLAN Priority.rw INTEGER .1.3.6.1.4.1.161.19.3.2.1.150 |
providerVIDPriorityModeProvider VID VLAN Priority Mode.rw Enumeration .1.3.6.1.4.1.161.19.3.2.1.151 |
additionalColorCodeAdd an additional color code. Setting additionalColorCode and additionalColorCodePriority adds an entry.rw INTEGER .1.3.6.1.4.1.161.19.3.2.1.152 |
additionalColorCodePriorityAdd an additional color code priority. Setting additionalColorCode and additionalColorCodePriority adds an entry.rw Enumeration .1.3.6.1.4.1.161.19.3.2.1.153 |
deleteAdditionalColorCodeDelete an additional color code.rw INTEGER .1.3.6.1.4.1.161.19.3.2.1.154 |
bCastMIRUnitsUnits of Broadcast/ Multicast MIR value. Set units first and then bCastMIRrw Enumeration .1.3.6.1.4.1.161.19.3.2.1.155 |
rfScanListTableThe list of configured scanning frequencies on the SM or BHS. SEQUENCE OF RfScanListEntry .1.3.6.1.4.1.161.19.3.2.1.156 |
rfScanListEntryEntry of configured scanning frequencies on the SM or BHS. RfScanListEntry .1.3.6.1.4.1.161.19.3.2.1.156.1 |
rfScanListFrequencyRF scan list. The frequencies vary by product and region.rw INTEGER .1.3.6.1.4.1.161.19.3.2.1.156.1.1 |
whispSmStatus OBJECT IDENTIFIER .1.3.6.1.4.1.161.19.3.2.2 |
sessionStatusSM registered or not.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.2.2.1 |
rssiRadio signal strength index. FSK only.ro INTEGER .1.3.6.1.4.1.161.19.3.2.2.2 |
jitterA measure of multipath interference. Applicable to FSK radios only.ro Gauge32 .1.3.6.1.4.1.161.19.3.2.2.3 |
airDelayRound trip delay in bits.ro Unsigned32 .1.3.6.1.4.1.161.19.3.2.2.4 |
radioSlicingSmThis variable is deprecated.roobsolete INTEGER .1.3.6.1.4.1.161.19.3.2.2.5 |
radioTxGainSmRadio transmission gain setting. Applicable to FSK radios only.ro INTEGER .1.3.6.1.4.1.161.19.3.2.2.6 |
calibrationStatusVarible deprecated. Please use calibrationStatusBox.rodeprecated DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.2.2.7 |
radioDbmRx Power level. For MIMO this is the combined power of the horizontal and vertical paths.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.2.2.8 |
registeredToApAP MAC address that the SM registered to.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.2.2.9 |
dhcpCipAssigned IP address to DHCP client.ro IpAddress .1.3.6.1.4.1.161.19.3.2.2.10 |
dhcpSipPublic DHCP server IP.ro IpAddress .1.3.6.1.4.1.161.19.3.2.2.11 |
dhcpClientLeaseDHCP client lease time.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.161.19.3.2.2.12 |
dhcpCSMaskPublic DHCP server subnet mask.ro IpAddress .1.3.6.1.4.1.161.19.3.2.2.13 |
dhcpDfltRterIPPublic default router IP address.ro IpAddress .1.3.6.1.4.1.161.19.3.2.2.14 |
dhcpcdns1Primary public domain name server.ro IpAddress .1.3.6.1.4.1.161.19.3.2.2.15 |
dhcpcdns2Secondary public domain name server.ro IpAddress .1.3.6.1.4.1.161.19.3.2.2.16 |
dhcpcdns3Third public domain name server.ro IpAddress .1.3.6.1.4.1.161.19.3.2.2.17 |
dhcpDomNamePublic domain name server.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.2.2.18 |
dhcpServerTableThe table of DHCP server hosts. SEQUENCE OF DhcpServerEntry .1.3.6.1.4.1.161.19.3.2.2.19 |
dhcpServerEntryEntry of DHCP server hosts. DhcpServerEntry .1.3.6.1.4.1.161.19.3.2.2.19.1 |
hostIpDHCP server IP address.ro IpAddress .1.3.6.1.4.1.161.19.3.2.2.19.1.1 |
hostMacAddressPrivate host MAC address.ro PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.2.2.19.1.2 |
hostLeaseLease time assigned by DHCP server host.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.161.19.3.2.2.19.1.3 |
adaptRateVC adapt rate.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.2.2.20 |
radioDbmIntRadio power level(integer). For MIMO radios this is the combined power of the horiztontal and vertical paths.ro INTEGER .1.3.6.1.4.1.161.19.3.2.2.21 |
dfsStatusDynamic frequency shifting status. For DFS Radio only.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.2.2.22 |
radioTxPwrTx Power level. Valid for FSK and OFDM SMs.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.2.2.23 |
activeRegionThe active region of the radio.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.2.2.24 |
snmpBerLevelBER level. For PMP 450 systems: 2=MIMO QPSK, 4=MIMO 16-QAM, 6=MIMO64-QAM, 8=256-QAM For non PMP 450: 2=2 level BER, 4=4 level BER.ro Enumeration .1.3.6.1.4.1.161.19.3.2.2.25 |
nbBitsRcvdNumber of BER bits received (non MIMO platforms only).ro Counter64 .1.3.6.1.4.1.161.19.3.2.2.26 |
nbPriBitsErrNumber of Primary bit errors (non MIMO platforms only).ro Counter32 .1.3.6.1.4.1.161.19.3.2.2.27 |
nbSndBitsErrNumber of secondary bit errors (non MIMO platforms only).ro Counter32 .1.3.6.1.4.1.161.19.3.2.2.28 |
primaryBERObsoleted, invalid type to represent this data. Measured Primary Bit Error Rate.roobsolete INTEGER .1.3.6.1.4.1.161.19.3.2.2.29 |
secondaryBERObsoleted, invalid type to represent this data. Measured Secondary Bit Error Rate.roobsolete INTEGER .1.3.6.1.4.1.161.19.3.2.2.30 |
totalBERObsoleted, invalid type to represent this data. Measured Total Bit Error Rate.roobsolete INTEGER .1.3.6.1.4.1.161.19.3.2.2.31 |
minRSSIMeasured Min. RSSI. Applicable to FSK radios only.ro INTEGER .1.3.6.1.4.1.161.19.3.2.2.32 |
maxRSSIMeasured Max. RSSI. Applicable to FSK radios only.ro INTEGER .1.3.6.1.4.1.161.19.3.2.2.33 |
minJitterMeasured Min. Jitter. Applicable to FSK radios only.ro Gauge32 .1.3.6.1.4.1.161.19.3.2.2.34 |
maxJitterMeasured Max. Jitter. Applicable to FSK radios only.ro Gauge32 .1.3.6.1.4.1.161.19.3.2.2.35 |
smSessionTimerSM current session timer.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.161.19.3.2.2.36 |
pppoeSessionStatusCurrent PPPoE Session Statusro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.2.2.37 |
pppoeSessionIDCurrent PPPoE Session IDro INTEGER .1.3.6.1.4.1.161.19.3.2.2.38 |
pppoeIPCPAddressCurrent PPPoE IPCP IP Addressro IpAddress .1.3.6.1.4.1.161.19.3.2.2.39 |
pppoeMTUOverrideEnCurrent PPPoE MTU Override Settingro Enumeration .1.3.6.1.4.1.161.19.3.2.2.40 |
pppoeMTUValueCurrent PPPoE MTU Valuero INTEGER .1.3.6.1.4.1.161.19.3.2.2.41 |
pppoeTimerTypeValueCurrent PPPoE Timer Type. 0 is disabled, 1 is Keep Alive timer, and 2 is Idle Timeout timer.ro Enumeration .1.3.6.1.4.1.161.19.3.2.2.42 |
pppoeTimeoutValueCurrent PPPoE Timeout Period. The use of this depends on the Timer Type. If the Timer Type is KeepAlive, then the timeout period is in seconds. If the Timer Type is Idle Timeout, then the timeout period is in minutes.ro INTEGER .1.3.6.1.4.1.161.19.3.2.2.43 |
pppoeDNSServer1PPPoE DNS Server 1ro IpAddress .1.3.6.1.4.1.161.19.3.2.2.44 |
pppoeDNSServer2PPPoE DNS Server 2ro IpAddress .1.3.6.1.4.1.161.19.3.2.2.45 |
pppoeControlBytesSentPPPoE Control Bytes Sentro Counter32 .1.3.6.1.4.1.161.19.3.2.2.46 |
pppoeControlBytesReceivedPPPoE Control Bytes Receivedro Counter32 .1.3.6.1.4.1.161.19.3.2.2.47 |
pppoeDataBytesSentPPPoE Data Bytes Sentro Counter32 .1.3.6.1.4.1.161.19.3.2.2.48 |
pppoeDataBytesReceivedPPPoE Data Bytes Receivedro Counter32 .1.3.6.1.4.1.161.19.3.2.2.49 |
pppoeEnabledStatusPPPoE Enabledro Enumeration .1.3.6.1.4.1.161.19.3.2.2.50 |
pppoeTCPMSSClampEnableStatusPPPoE TCP MSS Clamping Enablero Enumeration .1.3.6.1.4.1.161.19.3.2.2.51 |
pppoeACNameStatusCurrent PPPoE Access Concentrator In Usero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.2.2.52 |
pppoeSvcNameStatusCurrent PPPoE Service Name In Usero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.2.2.53 |
pppoeSessUptimeUptime of current PPPoE Session in ticksro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.161.19.3.2.2.54 |
primaryBERDisplayMeasured Primary Bit Error Rate. Non MIMO platforms only.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.2.2.55 |
secondaryBERDisplayMeasured Secondary Bit Error Rate. FSK platforms only.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.2.2.56 |
totalBERDisplayMeasured Total Bit Error Rate. For MIMO this is combined both paths.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.2.2.57 |
minRadioDbmMaximum receive power of beacon in dBm. For MIMO radios, this is only available in the vertical path.ro INTEGER .1.3.6.1.4.1.161.19.3.2.2.58 |
maxRadioDbmMaximum receive power in dBm (rounded to nearest integer).ro INTEGER .1.3.6.1.4.1.161.19.3.2.2.59 |
pppoeSessIdleTimeIdle Time of current PPPoE Session in ticksro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.161.19.3.2.2.60 |
radioDbmAvgAverage Receive Power of the AP's beacon in dBm. OFDM Radios only. For MIMO this is only the verical path, as the beacon is not transmitted on horizontal.ro INTEGER .1.3.6.1.4.1.161.19.3.2.2.61 |
zoltarFPGAFreqOffsetFPGA peek of 70001088ro INTEGER .1.3.6.1.4.1.161.19.3.2.2.62 |
zoltarSWFreqOffsetFPGA peek of 7000108Cro INTEGER .1.3.6.1.4.1.161.19.3.2.2.63 |
airDelaynsRound trip delay in nanoseconds.ro Unsigned32 .1.3.6.1.4.1.161.19.3.2.2.64 |
currentColorCodeThe current Color Code of the Registered AP/BHM. A value of -1 is return when the device is not registered.ro INTEGER .1.3.6.1.4.1.161.19.3.2.2.65 |
currentColorCodePriThe current priority of the Registered color codero Enumeration .1.3.6.1.4.1.161.19.3.2.2.66 |
currentChanFreqThe Current Channel Frequency of the AP/BHM when in session.ro Unsigned32 .1.3.6.1.4.1.161.19.3.2.2.67 |
linkQualityBeaconEngineering only. Link Quality for incoming beacons. For Gen II OFDM radios and forward. For PMP 450 and forward this is vertical path.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.2.2.68 |
dhcpServerPktXmtNumber of packets transmitted by SM DHCP Serverro Counter32 .1.3.6.1.4.1.161.19.3.2.2.72 |
dhcpServerPktRcvNumber of packets received by SM DHCP Serverro Counter32 .1.3.6.1.4.1.161.19.3.2.2.73 |
dhcpServerPktTossNumber of packets tossed by SM DHCP Serverro Counter32 .1.3.6.1.4.1.161.19.3.2.2.74 |
receiveFragmentsModulationPercentageEngineering use only. The percentage of recent fragments received at which modulation. For Gen II OFDM only and forward.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.2.2.86 |
fragmentsReceived1XVerticalEngineering use only. Number of fragments received in 1x modulation. For GenII OFDM only and forward. For MIMO this is the vertical path.ro Counter32 .1.3.6.1.4.1.161.19.3.2.2.87 |
fragmentsReceived2XVerticalEngineering use only. Number of fragments received in 2x modulation. For GenII OFDM only and forward. For MIMO this is the vertical path.ro Counter32 .1.3.6.1.4.1.161.19.3.2.2.88 |
fragmentsReceived3XVerticalEngineering use only. Number of fragments received in 3x modulation. For GenII OFDM only and forward. For MIMO this is the vertical path.ro Counter32 .1.3.6.1.4.1.161.19.3.2.2.89 |
fragmentsReceived4XVerticalEngineering use only. Number of fragments received in 4x modulation. For GenII OFDM only and forward. For MIMO this is the vertical path.ro Counter32 .1.3.6.1.4.1.161.19.3.2.2.90 |
linkQualityData1XVerticalEngineering use only. Link Quality for the data VC for QPSK modulation (1X). For Gen II OFDM radios and forward only. For MIMO this is the vertical path.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.2.2.91 |
linkQualityData2XVerticalEngineering use only. Link Quality for the data VC for 16-QAM modulation (2X). For Gen II OFDM radios and forward only. For MIMO this is the vertical path.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.2.2.92 |
linkQualityData3XVerticalEngineering use only. Link Quality for the data VC for 64-QAM modulation (3X). For Gen II OFDM radios and forward only. For MIMO this is the vertical path.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.2.2.93 |
linkQualityData4XVerticalEngineering use only. Link Quality for the data VC for 256-QAM modulation (4X). For Gen II OFDM radios and forward only. For MIMO this is the vertical path.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.2.2.94 |
signalToNoiseRatioSMVerticalAn estimated signal to noise ratio based on the last received data. For GenII OFDM only and forward. For MIMO this is the vertical antenna. Will return zero if Signal to Noise Ratio Calculation is disabled.ro INTEGER .1.3.6.1.4.1.161.19.3.2.2.95 |
rfStatTxSuppressionCountRF Scheduler Stats DFS TX Suppression Countro Counter32 .1.3.6.1.4.1.161.19.3.2.2.96 |
bridgecbUplinkCreditRateSustained uplink data rate.ro Unsigned32 .1.3.6.1.4.1.161.19.3.2.2.97 |
bridgecbUplinkCreditLimitUplink Burst Allocation.ro Unsigned32 .1.3.6.1.4.1.161.19.3.2.2.98 |
bridgecbDownlinkCreditRateSustained uplink data rate.ro Unsigned32 .1.3.6.1.4.1.161.19.3.2.2.99 |
bridgecbDownlinkCreditLimitUplink Burst Allocation.ro Unsigned32 .1.3.6.1.4.1.161.19.3.2.2.100 |
mimoQpskBerDisplayQPSK BER statistics. MIMO platforms only.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.2.2.101 |
mimo16QamBerDisplay16-QAM BER statistics MIMO platforms only. Engineering use only.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.2.2.102 |
mimo64QamBerDisplay64-QAM BER statistics MIMO platforms only. Engineering use only.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.2.2.103 |
mimo256QamBerDisplay256-QAM BER statistics MIMO platforms only. Engineering use only.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.2.2.104 |
mimoBerRcvModulationTypeReceive modulation type. MIMO platforms only.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.2.2.105 |
signalToNoiseRatioSMHorizontalAn estimated signal to noise ratio based on the last received data for horizontal antenna. MIMO radios only. Will return zero if Signal to Noise Ratio Calculation is disabled. When operating in MIMO-A will return 0.ro INTEGER .1.3.6.1.4.1.161.19.3.2.2.106 |
maxRadioDbmDeprecatedThis OID was inadvertently moved in 12.0.2. Please use maxRadioDbm. This OID is deprecated and kept for backwards compatibility.rodeprecated INTEGER .1.3.6.1.4.1.161.19.3.2.2.107 |
signalStrengthRatioSignal Strength Ratio in dB is the power received by the vertical antenna input (dB) - power received by the horizontal antenna input (dB). MIMO radios only.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.2.2.108 |
fragmentsReceived1XHorizontalEngineering use only. Number of fragments received in 1x modulation. For MIMO radios only. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical.ro Counter32 .1.3.6.1.4.1.161.19.3.2.2.109 |
fragmentsReceived2XHorizontalEngineering use only. Number of fragments received in 2x modulation. For MIMO radios only. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical.ro Counter32 .1.3.6.1.4.1.161.19.3.2.2.110 |
fragmentsReceived3XHorizontalEngineering use only. Number of fragments received in 3x modulation. For MIMO radios only. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical.ro Counter32 .1.3.6.1.4.1.161.19.3.2.2.111 |
fragmentsReceived4XHorizontalEngineering use only. Number of fragments received in 4x modulation. For MIMO radios only. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical.ro Counter32 .1.3.6.1.4.1.161.19.3.2.2.112 |
linkQualityData1XHorizontalEngineering use only. Link Quality for the data VC for QPSK modulation (1X). For MIMO radios only. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.2.2.113 |
linkQualityData2XHorizontalEngineering use only. Link Quality for the data VC for 16-QAM modulation (2X). For MIMO radios only. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.2.2.114 |
linkQualityData3XHorizontalEngineering use only. Link Quality for the data VC for 64-QAM modulation (3X). For MIMO radios only. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.2.2.115 |
linkQualityData4XHorizontalEngineering use only. Link Quality for the data VC for 256-QAM modulation (4X). For MIMO radios only. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.2.2.116 |
radioDbmHorizontalReceive power level of the horizontal antenna in dBm. MIMO radios only.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.2.2.117 |
radioDbmVerticalReceive power level of the vertical antenna in dBm. MIMO radios only.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.2.2.118 |
bridgecbDownlinkMaxBurstBitRateMaximum burst downlink rate.ro Unsigned32 .1.3.6.1.4.1.161.19.3.2.2.119 |
bridgecbUplinkMaxBurstBitRateMaximum burst uplink Rate.ro Unsigned32 .1.3.6.1.4.1.161.19.3.2.2.120 |
currentCyclicPrefixThe Current Cyclic Prefix of the AP/BHM when in session.ro Enumeration .1.3.6.1.4.1.161.19.3.2.2.121 |
currentBandwidthThe Current Bandwidth of the AP/BHM when in session.ro Enumeration .1.3.6.1.4.1.161.19.3.2.2.122 |
berPwrRxFPGAPathABER power level on FPGA Rx Path A of SM. Engineering Use Only.ro INTEGER .1.3.6.1.4.1.161.19.3.2.2.123 |
berPwrRxFPGAPathBBER power level on FPGA Rx Path B of SM. Engineering Use Only.ro INTEGER .1.3.6.1.4.1.161.19.3.2.2.124 |
rawBERPwrRxPathARaw unadjusted BER power level on FPGA Rx Path A of SM. Engineering Use Only.ro INTEGER .1.3.6.1.4.1.161.19.3.2.2.125 |
rawBERPwrRxPathBRaw unadjusted BER power level on FPGA Rx Path B of SM. Engineering Use Only.ro INTEGER .1.3.6.1.4.1.161.19.3.2.2.126 |
radioModeStatusThe current radio mode that SM is operating in. PMP 430 SMs only. Introduced in release 12.2.ro Enumeration .1.3.6.1.4.1.161.19.3.2.2.127 |
adaptRateLowPriThe current transmitting rate of the low priority VC. 0 : SM is not in session 1 : 1X QPSK SISO 2 : 2X 16-QAM SISO or QPSK MIMO 3 : 3X 64-QAM SISO 4 : 4X 256-QAM SISO or 16-QAM MIMO 6 : 6X 64-QAM MIMO 8 : 8X 256-QAM MIMOro Enumeration .1.3.6.1.4.1.161.19.3.2.2.128 |
adaptRateHighPriThe current transmitting rate of the high priority VC. -1 : High Priority Channel not configured 0 : SM is not in session 1 : 1X QPSK SISO 2 : 2X 16-QAM SISO or QPSK MIMO 3 : 3X 64-QAM SISO 4 : 4X 256-QAM SISO or 16-QAM MIMO 6 : 6X 64-QAM MIMO 8 : 8X 256-QAM MIMOro Enumeration .1.3.6.1.4.1.161.19.3.2.2.129 |
bitErrorsQSPKpathANumber of bit errors received from BER packet at QPSK path A. Valid MIMO platforms only.ro Counter64 .1.3.6.1.4.1.161.19.3.2.2.130 |
bitErrorsQSPKpathBNumber of bit errors received from BER packet at QPSK path B. Valid MIMO platforms only.ro Counter64 .1.3.6.1.4.1.161.19.3.2.2.131 |
bitErrors16QAMpathANumber of bit errors received from BER packet at 16-QAM path A. Valid MIMO platforms only. Engineering use only.ro Counter64 .1.3.6.1.4.1.161.19.3.2.2.132 |
bitErrors16QAMpathBNumber of bit errors received from BER packet at 16-QAM path B. Valid MIMO platforms only. Engineering use only.ro Counter64 .1.3.6.1.4.1.161.19.3.2.2.133 |
bitErrors64QAMpathANumber of bit errors received from BER packet at 64-QAM path A. Valid MIMO platforms only. Engineering use only.ro Counter64 .1.3.6.1.4.1.161.19.3.2.2.134 |
bitErrors64QAMpathBNumber of bit errors received from BER packet at 64-QAM path B. Valid MIMO platforms only. Engineering use only.ro Counter64 .1.3.6.1.4.1.161.19.3.2.2.135 |
bitErrors256QAMpathANumber of bit errors received from BER packet at 256-QAM path A. Valid MIMO platforms only. Engineering use only.ro Counter64 .1.3.6.1.4.1.161.19.3.2.2.136 |
bitErrors256QAMpathBNumber of bit errors received from BER packet at 256-QAM path B. Valid MIMO platforms only. Engineering use only.ro Counter64 .1.3.6.1.4.1.161.19.3.2.2.137 |
bitsReceivedPerPathModulationNumber of bit received from BER. To calculate Bit Error Rate, take bit errors at a modulation and path and divide by this OID. To get combined BER add errors and divide by this multiplied by each path and modulation. i.e. MIMO QPSK combined BER = ((errors on path A) + (errors on path B))/(bits recieved per path modulation * 2) Valid MIMO platforms only.ro Counter64 .1.3.6.1.4.1.161.19.3.2.2.138 |
beaconsPercentReceivedThe current percentage of beacons that the SM/BHS successfully receiving.ro INTEGER .1.3.6.1.4.1.161.19.3.2.2.139 |
mapsPercentReceivedPMP 450 only. The current percentage of scheduling maps that the SM/BHS successfully receiving.ro INTEGER .1.3.6.1.4.1.161.19.3.2.2.140 |
natTslTableEntriesNumber of Entries in NAT Translation Table.ro INTEGER .1.3.6.1.4.1.161.19.3.2.2.141 |
maxReceivePowerMaximum receive power level for this session. MIMO radios only.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.2.2.142 |
beaconsPercentMinReceivedThe percentage of the least number of beacons that the SM/BHS successfully received in a 16 second window for the last 15 minutes. This will be updated only once in 15 minutes.ro INTEGER .1.3.6.1.4.1.161.19.3.2.2.143 |
beaconsPercentMaxReceivedThe percentage of the maximum number of beacons that the SM/BHS successfully received in a 16 second window for the last 15 minutes. This will be updated only once in 15 minutes.ro INTEGER .1.3.6.1.4.1.161.19.3.2.2.144 |
beaconsPercentReceivedSnapshotThe percentage of beacons that the SM/BHS successfully received for the last 15 minutes. This will be updated only once in 15 minutes.ro INTEGER .1.3.6.1.4.1.161.19.3.2.2.145 |
whispSmGroups OBJECT IDENTIFIER .1.3.6.1.4.1.161.19.3.2.3 |
whispSmConfigGroupCanopy Subscriber Module configuration group. Unknown .1.3.6.1.4.1.161.19.3.2.3.1 |
whispSmStatusGroupCanopy Subscriber Module status group. Unknown .1.3.6.1.4.1.161.19.3.2.3.2 |
whispSmNotifGroupWHiSP SMs notification group. Unknown .1.3.6.1.4.1.161.19.3.2.3.3 |
whispMappingTableGroupCanopy SM NAT port mapping Table group. Unknown .1.3.6.1.4.1.161.19.3.2.3.4 |
whispSmEvent OBJECT IDENTIFIER .1.3.6.1.4.1.161.19.3.2.4 |
whispSmDfsEvent OBJECT IDENTIFIER .1.3.6.1.4.1.161.19.3.2.4.1 |
whispRadarDetectedRadar detected transmit stopped. NOTIFICATION-TYPE .1.3.6.1.4.1.161.19.3.2.4.1.1 |
whispRadarEndRadar ended back to normal transmit. NOTIFICATION-TYPE .1.3.6.1.4.1.161.19.3.2.4.1.2 |
whispSmSpAnEvent OBJECT IDENTIFIER .1.3.6.1.4.1.161.19.3.2.4.2 |
enterSpectrumAnalysisEntering spectrum analysis. physAddress - MAC address of the SM NOTIFICATION-TYPE .1.3.6.1.4.1.161.19.3.2.4.2.1 |
availableSpectrumAnalysisSpectrum analysis is complete, SM is re-registered with AP and results are available. physAddress - MAC address of the SM NOTIFICATION-TYPE .1.3.6.1.4.1.161.19.3.2.4.2.2 |
whispSmDHCPClientEvent OBJECT IDENTIFIER .1.3.6.1.4.1.161.19.3.2.4.3 |
smNatWanDHCPClientEventNAT WAN DHCP Client has received a new address via DHCP. NOTIFICATION-TYPE .1.3.6.1.4.1.161.19.3.2.4.3.1 |
smNatRFPubDHCPClientEventNAT RF Public DHCP Client has received a new address via DHCP. NOTIFICATION-TYPE .1.3.6.1.4.1.161.19.3.2.4.3.2 |
whispMappingTableNAT port mapping information table. SEQUENCE OF WhispMappingEntry .1.3.6.1.4.1.161.19.3.2.5 |
whispMappingEntryMapping table entry. WhispMappingEntry .1.3.6.1.4.1.161.19.3.2.5.1 |
tableIndexUser information table index.ro INTEGER .1.3.6.1.4.1.161.19.3.2.5.1.1 |
protocolProtocol type: 0:both UDP and TCP, 1:UDP, 2:TCP.rw INTEGER .1.3.6.1.4.1.161.19.3.2.5.1.2 |
portApplication port number. e.g. 23=telnet, 21=ftp etc. Should be a positive integer.rw INTEGER .1.3.6.1.4.1.161.19.3.2.5.1.3 |
localIpIP of local host to which the incoming packet mapped to an application should be forwarded.rw IpAddress .1.3.6.1.4.1.161.19.3.2.5.1.4 |
whispSmTranslationTableTranslation Table. SEQUENCE OF WhispSmTranslationTableEntry .1.3.6.1.4.1.161.19.3.2.6 |
whispSmTranslationTableEntryTranslation Table Entry. WhispSmTranslationTableEntry .1.3.6.1.4.1.161.19.3.2.6.1 |
whispTranslationTableIndexIndex into translation table.ro INTEGER .1.3.6.1.4.1.161.19.3.2.6.1.1 |
whispTranslationTableMacAddrMAC Address of the registered enity.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.2.6.1.2 |
whispTranslationTableIpAddrIp Address of the registered entity.ro IpAddress .1.3.6.1.4.1.161.19.3.2.6.1.3 |
whispTranslationTableAgeAge of the registered entity.ro Counter32 .1.3.6.1.4.1.161.19.3.2.6.1.4 |
whispSmSecurity OBJECT IDENTIFIER .1.3.6.1.4.1.161.19.3.2.7 |
certTableThe table of CA Certificates on SM. SEQUENCE OF CertEntry .1.3.6.1.4.1.161.19.3.2.7.1 |
certEntryEntry of Certifcates. CertEntry .1.3.6.1.4.1.161.19.3.2.7.1.1 |
certIndexUser information table index.ro INTEGER .1.3.6.1.4.1.161.19.3.2.7.1.1.1 |
cert0: Inactive 1: Activero Enumeration .1.3.6.1.4.1.161.19.3.2.7.1.1.2 |
action0: No Operation 1: Delete Certificaterw Enumeration .1.3.6.1.4.1.161.19.3.2.7.1.1.3 |
certificateDNDistinguished Name of Certificate 2ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.2.7.1.1.4 |
numAuthCertscan have a max value of 2ro INTEGER .1.3.6.1.4.1.161.19.3.2.7.2 |
authenticationEnforceenforce SM to register with specifed Auth Enabled APrw Enumeration .1.3.6.1.4.1.161.19.3.2.7.3 |
phase1Select the outer method for EAP Authentication. Note: PEAP is not supported for MPC860 platform.rw Enumeration .1.3.6.1.4.1.161.19.3.2.7.4 |
phase2Select the outer method for EAP Authenticationrw Enumeration .1.3.6.1.4.1.161.19.3.2.7.5 |
authOuterIdEAP Peer Usernamerw OCTET STRING .1.3.6.1.4.1.161.19.3.2.7.6 |
authPasswordEAP Peer passwordrw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.2.7.7 |
authUsernameEAP Peer Identityrw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.2.7.8 |
useRealmEnable or disable the use of realm option.rw Enumeration .1.3.6.1.4.1.161.19.3.2.7.9 |
realmEAP Peer Realmrw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.2.7.10 |
whispSmControls OBJECT IDENTIFIER .1.3.6.1.4.1.161.19.3.2.8 |
clearLinkStatsSetting this to a nonzero value will clear the link stats.rw INTEGER .1.3.6.1.4.1.161.19.3.2.8.1 |
rescanSetting this to a nonzero value will start the rescan. Warning: If currently connected, this will cause the SM/BHS to drop sessionrw INTEGER .1.3.6.1.4.1.161.19.3.2.8.2 |
whispSmColorCodeTableAdditional color code Table. SEQUENCE OF WhispSmColorCodeEntry .1.3.6.1.4.1.161.19.3.2.9 |
whispSmColorCodeEntryAdditional Color code Entry. WhispSmColorCodeEntry .1.3.6.1.4.1.161.19.3.2.9.1 |
entryColorCodecolor code.ro INTEGER .1.3.6.1.4.1.161.19.3.2.9.1.1 |
entryColorCodePrioritycolor code priority.ro Enumeration .1.3.6.1.4.1.161.19.3.2.9.1.2 |
whispSmAPEvalTableAP Eval List. SEQUENCE OF WhispSmAPEvalEntry .1.3.6.1.4.1.161.19.3.2.10 |
whispSmAPEvalEntryEvaluation of AP and BHM Entries WhispSmAPEvalEntry .1.3.6.1.4.1.161.19.3.2.10.1 |
evalIndexIndex of the radio seen in the scanro INTEGER .1.3.6.1.4.1.161.19.3.2.10.1.1 |
evalFrequencyTransmit Frequency in KHzro INTEGER .1.3.6.1.4.1.161.19.3.2.10.1.2 |
evalChannelBandwidthChannel Bandwidthro Enumeration .1.3.6.1.4.1.161.19.3.2.10.1.3 |
evalCyclicPrefixCyclic Prefix value, for OFDM Radios only.ro Enumeration .1.3.6.1.4.1.161.19.3.2.10.1.4 |
evalESNRadio ESNro PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.2.10.1.5 |
evalRegionRegionro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.2.10.1.6 |
evalBeaconReceivePowerCombinedBeacon Receive Power Combined in dBm(rounded to nearest integer)ro INTEGER .1.3.6.1.4.1.161.19.3.2.10.1.7 |
evalBeaconReceivePowerHBeacon Receive Power in dBm(rounded to nearest integer) for Path H(MIMO Radios only)ro INTEGER .1.3.6.1.4.1.161.19.3.2.10.1.8 |
evalBeaconReceivePowerVBeacon Receive Power in dBm(rounded to nearest integer) for Path V(MIMO Radios only)ro INTEGER .1.3.6.1.4.1.161.19.3.2.10.1.9 |
evalFECEnableForward Error Correction Enabled Status. Note, this is always enabled on 450 and forward.ro Enumeration .1.3.6.1.4.1.161.19.3.2.10.1.10 |
evalTypeRadio Type (Point-to-Point or Multipoint)ro Enumeration .1.3.6.1.4.1.161.19.3.2.10.1.11 |
evalAvailReturns True if seen on the previous SM's scanro Enumeration .1.3.6.1.4.1.161.19.3.2.10.1.12 |
evalAgeNumber of minutes since index was last seenro INTEGER .1.3.6.1.4.1.161.19.3.2.10.1.13 |
evalLockoutNumber of minutes radio is currently locked outro INTEGER .1.3.6.1.4.1.161.19.3.2.10.1.14 |
evalRegFailRegistration Fail Countro INTEGER .1.3.6.1.4.1.161.19.3.2.10.1.15 |
evalRangeRange in feetro INTEGER .1.3.6.1.4.1.161.19.3.2.10.1.16 |
evalMaxRangeMax Range is in milesro INTEGER .1.3.6.1.4.1.161.19.3.2.10.1.17 |
evalTxBERRadio is transmitting Bit Error Rate symbol or not Note: This is always enabled on 450 and forwardro Enumeration .1.3.6.1.4.1.161.19.3.2.10.1.18 |
evalEBCastBroadcast Encryption statusro Enumeration .1.3.6.1.4.1.161.19.3.2.10.1.19 |
evalSessionCountSession Countro INTEGER .1.3.6.1.4.1.161.19.3.2.10.1.20 |
evalNoLuidNumber of times the registration request has been rejected due to No Luidro INTEGER .1.3.6.1.4.1.161.19.3.2.10.1.21 |
evalOutOfRangeNumber of times the registration request has been rejected due to out of rangero INTEGER .1.3.6.1.4.1.161.19.3.2.10.1.22 |
evalAuthFailNumber of times the registration request has been rejected due to authentication failurero INTEGER .1.3.6.1.4.1.161.19.3.2.10.1.23 |
evalEncryptFailNumber of times the registration request has been rejected due to encrypt failro INTEGER .1.3.6.1.4.1.161.19.3.2.10.1.24 |
evalReScanReqRescan request countro INTEGER .1.3.6.1.4.1.161.19.3.2.10.1.25 |
evalLimitReachedNumber of times failed when trying to register with an limited AP maxed outro INTEGER .1.3.6.1.4.1.161.19.3.2.10.1.26 |
evalNoVCsNumber of times the registration request has been rejected due to No VCsro INTEGER .1.3.6.1.4.1.161.19.3.2.10.1.27 |
evalVCReserveFailNumber of times the registration request has been rejected due to VC reserve failro INTEGER .1.3.6.1.4.1.161.19.3.2.10.1.28 |
evalVCActFailNumber of times the registration request has been rejected due to VC activate failro INTEGER .1.3.6.1.4.1.161.19.3.2.10.1.29 |
evalTxPowerTransmit Power in dBmro INTEGER .1.3.6.1.4.1.161.19.3.2.10.1.30 |
evalReceiveTargetLevelReceive Target Level(in dBm)(PMP only)ro INTEGER .1.3.6.1.4.1.161.19.3.2.10.1.31 |
evalColorCodeColor Codero INTEGER .1.3.6.1.4.1.161.19.3.2.10.1.32 |
evalBeaconVersionBeacon Versionro INTEGER .1.3.6.1.4.1.161.19.3.2.10.1.33 |
evalSectorUserCountSector User Count(AP only)ro INTEGER .1.3.6.1.4.1.161.19.3.2.10.1.34 |
evalSyncSrcSync Source(PMP only)ro Enumeration .1.3.6.1.4.1.161.19.3.2.10.1.35 |
evalNumULSlotsNumber of uplink slotsro INTEGER .1.3.6.1.4.1.161.19.3.2.10.1.36 |
evalNumDLSlotsNumber of downlink slotsro INTEGER .1.3.6.1.4.1.161.19.3.2.10.1.37 |
evalNumULContSlotsNumber of uplink contention slots(PMP only)ro INTEGER .1.3.6.1.4.1.161.19.3.2.10.1.38 |
evalICCInstalaton Color Code(PMP only)ro Enumeration .1.3.6.1.4.1.161.19.3.2.10.1.39 |
evalAuthenticationAuthentication Setting(PMP only)ro Enumeration .1.3.6.1.4.1.161.19.3.2.10.1.40 |
evalSMPPPoESM PPPoE status(PMP only)ro Enumeration .1.3.6.1.4.1.161.19.3.2.10.1.41 |
evalPToPVLANPToP VLANro Enumeration .1.3.6.1.4.1.161.19.3.2.10.1.42 |
evalFramePeriodFrame Periodro Enumeration .1.3.6.1.4.1.161.19.3.2.10.1.43 |