WHISP-APS-MIB
AI MIB Summary
The WHISP-APS-MIB module provides SNMP definitions for monitoring and managing Access Point (AP) operational states and performance metrics within the WHISP wireless infrastructure. It enables the collection of device-specific telemetry, including interface statistics, radio status, and association data, to facilitate real-time network visibility and fault isolation.
This module contains MIB definitions for APs.
Main OID:
whispApsMibModule.1.3.6.1.4.1.161.19.1.1.12
475
Objects
Active
Status
6
Dependencies
Imported Objects
Objects
475 total| Object Name |
|---|
whispApsMibModuleThis module contains MIB definitions for APs. MODULE-IDENTITY .1.3.6.1.4.1.161.19.1.1.12 |
whispApsConfig OBJECT IDENTIFIER .1.3.6.1.4.1.161.19.3.1.1 |
gpsInputThe variable is deprecated. See gpsInput in whispBoxConfig.rwobsolete Enumeration .1.3.6.1.4.1.161.19.3.1.1.1 |
rfFreqCarrierThe primary transmit frequency. Also see radioFreqCarrier.rwdeprecated Enumeration .1.3.6.1.4.1.161.19.3.1.1.2 |
apLinkSpeedThe variable is deprecated.rwobsolete DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.1.1.3 |
dwnLnkDataThis attribute is deprecated. Please see radioDownlinkPercent.rwdeprecated INTEGER .1.3.6.1.4.1.161.19.3.1.1.4 |
highPriorityUpLnkPctPercentage of uplink slots for high priority data.rwobsolete INTEGER .1.3.6.1.4.1.161.19.3.1.1.5 |
numUAckSlotsTotal number of upstream ack slots.rwobsolete INTEGER .1.3.6.1.4.1.161.19.3.1.1.6 |
uAcksReservHighTotal number of upstream high priority ack slotsrwobsolete INTEGER .1.3.6.1.4.1.161.19.3.1.1.7 |
numDAckSlotsTotal number of downstream ack slots.rwobsolete INTEGER .1.3.6.1.4.1.161.19.3.1.1.8 |
dAcksReservHighTotal number of high priority downstream ack slots.rwobsolete INTEGER .1.3.6.1.4.1.161.19.3.1.1.9 |
numCtlSlotsThis OID is deprecated, please use numCtlSlotsHW.rwobsolete INTEGER .1.3.6.1.4.1.161.19.3.1.1.10 |
numCtlSlotsReserveHighTotal number of High priority upstream control (contention) slots.rwobsolete INTEGER .1.3.6.1.4.1.161.19.3.1.1.11 |
upLnkDataRateSustained uplink bandwidth cap.rw INTEGER UNITS "Kilobits/sec" .1.3.6.1.4.1.161.19.3.1.1.12 |
upLnkLimitBurst uplink bandwidth cap.rw INTEGER UNITS "Kilobits/sec" .1.3.6.1.4.1.161.19.3.1.1.13 |
dwnLnkDataRateSustained downlink bandwidth cap.rw INTEGER UNITS "Kilobits/sec" .1.3.6.1.4.1.161.19.3.1.1.14 |
dwnLnkLimitBurst downlink bandwidth cap.rw INTEGER UNITS "Kilobits/sec" .1.3.6.1.4.1.161.19.3.1.1.15 |
sectorIDAdvertise sector number for an AP. Not supported on 450 platform.rw INTEGER .1.3.6.1.4.1.161.19.3.1.1.16 |
maxRangeThis attribute is deprecated. Please see radioMaxRange.rwdeprecated INTEGER UNITS "miles" .1.3.6.1.4.1.161.19.3.1.1.17 |
airLinkSecurityAir Link Security. desEnhancedAndAuthentication(2) and authenticationIfAvailable(3) are only for APAS.rwobsolete Enumeration .1.3.6.1.4.1.161.19.3.1.1.18 |
berModeAP backgroup BER mode.rwobsolete Enumeration .1.3.6.1.4.1.161.19.3.1.1.19 |
asIP1Obsoleted. Configure with whispApsDNS.authServer1.rwobsolete IpAddress .1.3.6.1.4.1.161.19.3.1.1.20 |
asIP2Obsoleted. Configure with whispApsDNS.authServer2.rwobsolete IpAddress .1.3.6.1.4.1.161.19.3.1.1.21 |
asIP3Obsoleted. Configure with whispApsDNS.authServer3.rwobsolete IpAddress .1.3.6.1.4.1.161.19.3.1.1.22 |
lanIpApLAN IP.rw IpAddress .1.3.6.1.4.1.161.19.3.1.1.23 |
lanMaskApLAN subnet mask.rw IpAddress .1.3.6.1.4.1.161.19.3.1.1.24 |
defaultGwApDefault gatewayrw IpAddress .1.3.6.1.4.1.161.19.3.1.1.25 |
privateIpPrivate IP.rw IpAddress .1.3.6.1.4.1.161.19.3.1.1.26 |
gpsTrapVariable to enable/disable GPS sync/out-sync traps.rw Enumeration .1.3.6.1.4.1.161.19.3.1.1.27 |
regTrapVariable to enable/disable registration complete/lost traps.rw Enumeration .1.3.6.1.4.1.161.19.3.1.1.28 |
txSpreadingVariable to enable/disable Transmit Frame Spreading. This option is for FSK only.rw Enumeration .1.3.6.1.4.1.161.19.3.1.1.29 |
apBeaconInfoVariable to enable/disable displaying AP beacon info through AP eval.rw Enumeration .1.3.6.1.4.1.161.19.3.1.1.30 |
authModeVariable to enable/disable authentication. The authentication optional mode is for APs only. This variable can only be set when authentication feature is enabled. Setting it to 1 will use a BAM server for authentication of SMs. Setting it to 2 will make use of the Authentication Key on the AP for authenticating SMs. The keys must match on SM and AP in order for the SM to be authenticated in this mode.rw Enumeration .1.3.6.1.4.1.161.19.3.1.1.31 |
authKeyApAuthentication key. It should be 32 character long. Can be used on MultiPoint AP if AP Authentication mode is selected. Otherwise, it is used on Backhauls.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.1.1.32 |
encryptionModeVariable to enable/disable encryption.rw Enumeration .1.3.6.1.4.1.161.19.3.1.1.33 |
ntpServerIpObsoleted. Configure with whispApsDNS.ntpServer1, whispApsDNS.ntpServer2, and whispApsDNS.ntpServer3.rwobsolete IpAddress .1.3.6.1.4.1.161.19.3.1.1.34 |
broadcastRetryCountBroadcast Repeat Count : Range 0 -- 2. For APs.rw INTEGER .1.3.6.1.4.1.161.19.3.1.1.35 |
encryptDwBroadcastTo enable or disable Encrypted Downlink Broadcast. For FSK APs.rw Enumeration .1.3.6.1.4.1.161.19.3.1.1.36 |
updateAppAddressUpdate Application Address.rw IpAddress .1.3.6.1.4.1.161.19.3.1.1.37 |
dfsConfigTo configure proper regions for Dynamic Frequency Shifting. For 5.2/5.4/5.7 GHz radios.rwobsolete Enumeration .1.3.6.1.4.1.161.19.3.1.1.38 |
vlanEnableTo enable or disable VLAN.rw Enumeration .1.3.6.1.4.1.161.19.3.1.1.39 |
configSourceTo configure CIR, MIR and VLAN through SM or BAM.rw Enumeration .1.3.6.1.4.1.161.19.3.1.1.40 |
apRateAdaptTo enable or disable double rate.rwobsolete Enumeration .1.3.6.1.4.1.161.19.3.1.1.41 |
numCtlSlotsHWThis attribute is deprecated. Please see radioControlSlots.rwdeprecated INTEGER .1.3.6.1.4.1.161.19.3.1.1.42 |
displayAPEvalIf enable, it allows display of AP Eval Data at the SM.rw Enumeration .1.3.6.1.4.1.161.19.3.1.1.43 |
smIsolation(0) -- Disable SM Isolation. (1) -- Enable SM Isolation by blocking SM destined packets. (2) -- Enable SM Isolation by forwarding SM packets upstream.rw Enumeration .1.3.6.1.4.1.161.19.3.1.1.44 |
ipAccessFilterEnableTo enable or disable IP access filtering to Management functions. (0) - IP access will be allowed from all addresses. (1) - IP access will be controlled using allowedIPAccess1-3 entries.rw Enumeration .1.3.6.1.4.1.161.19.3.1.1.45 |
allowedIPAccess1Allow access to AP Management from this IP. 0 is default setting to allow from all IPs.rw IpAddress .1.3.6.1.4.1.161.19.3.1.1.46 |
allowedIPAccess2Allow access to AP Management from this IP. 0 is default setting to allow from all IPs.rw IpAddress .1.3.6.1.4.1.161.19.3.1.1.47 |
allowedIPAccess3Allow access to AP Management from this IP. 0 is default setting to allow from all IPs.rw IpAddress .1.3.6.1.4.1.161.19.3.1.1.48 |
tslBridging1 = We are performing Translation Bridging 0 = We are not.rw Enumeration .1.3.6.1.4.1.161.19.3.1.1.49 |
untranslatedArp1 = We are sending untranslated ARP response. 0 = We are not.rw Enumeration .1.3.6.1.4.1.161.19.3.1.1.50 |
limitFreqBand9001 = We are limiting the freq band of 900 radios. 0 = We are not.rw Enumeration .1.3.6.1.4.1.161.19.3.1.1.51 |
txPwrLevelDeprecated, use 'transmitterOP' instead.rwobsolete INTEGER .1.3.6.1.4.1.161.19.3.1.1.52 |
rfFreqCaralt1First DFS Alternate RF Frequency. (Only available for DFS radios) Used as a backup frequency when Radar is detected on DFS enabled Radios. The frequencies are: 5.4 radios:(5475,5485,5490 OFDM only),5495,5500,5505,5510,5515,5520,5525, 5530,5535,5540,5545,5550,5555,5560,5565,5570,5575,5580,5585,5590,5595, 5600,5605,5610,5615,5620,5625,5630,5635,5640,5645,5650,5655,5660,5665, 5670,5675,5680,5685,5690,5695,5700,5705,(5710,5715 OFDM Only). (5.7 Platform 10 (SAL) radios with non-connectorized antennas do not support DFS) 5.7 radios:5745,5750,5755,5760,5765,5770,5775,5780,5785,5790,5795,5800,5805. 5.7 radios with ISM enabled :5735,5740,5745,5750,5755,5760,5765,5770,5775, 5780,5785,5790,5795,5800,5805,5810,5815,5820,5825,5830,5835,5840. 0: None.rw Enumeration .1.3.6.1.4.1.161.19.3.1.1.53 |
rfFreqCaralt2Second DFS Alternate RF Frequency. (Only available for DFS radios) Used as a backup frequency when Radar is detected on DFS enabled Radios. The frequencies are: 5.4 radios:(5475,5485,5490 OFDM only),5495,5500,5505,5510,5515,5520,5525, 5530,5535,5540,5545,5550,5555,5560,5565,5570,5575,5580,5585,5590,5595, 5600,5605,5610,5615,5620,5625,5630,5635,5640,5645,5650,5655,5660,5665, 5670,5675,5680,5685,5690,5695,5700,5705,(5710,5715 OFDM Only). (5.7 Platform 10 (SAL) radios with non-connectorized antennas do not support DFS) 5.7 radios:5745,5750,5755,5760,5765,5770,5775,5780,5785,5790,5795,5800,5805. 5.7 radios with ISM enabled :5735,5740,5745,5750,5755,5760,5765,5770,5775, 5780,5785,5790,5795,5800,5805,5810,5815,5820,5825,5830,5835,5840. 0: None.rw Enumeration .1.3.6.1.4.1.161.19.3.1.1.54 |
scheduleWhitening1 = Schedule Whitening allowed. 0 = Schedule Whitening not allowed. This option is for FSK onlyrw Enumeration .1.3.6.1.4.1.161.19.3.1.1.55 |
remoteSpectrumAnalysisDurationValue in seconds for a remote spectrum analysis on an SM. Range is 10-1000 seconds.rw INTEGER .1.3.6.1.4.1.161.19.3.1.1.56 |
remoteSpectrumAnalyzerLUIDGet will always return 0. Set will start Remote Spectrum Analyzer on specified LUID. *Warning* This will cause the SM to disconnect from the AP! You will lose the session for the specified duration! If general error was returned then the LUID does not have an active session, or the SM does not support Remote Spectrum Analysis.rw INTEGER .1.3.6.1.4.1.161.19.3.1.1.57 |
bhReRegAllows BHS re-registration every 24 hours. Enable allows re-registration and Disable does not. 24 Hour Encryption Refresh.rw Enumeration .1.3.6.1.4.1.161.19.3.1.1.58 |
dlnkBcastCIRDownlink Broadcast CIR (kbps)rw INTEGER .1.3.6.1.4.1.161.19.3.1.1.59 |
verifyGPSChecksumEnable/Disable verification of GPS message checksums.rw Enumeration .1.3.6.1.4.1.161.19.3.1.1.60 |
apVlanOverrideSetting this option will cause an AP to retain its VLAN settings when turning it into an SM. It will be mostly helpful for running spectrum analysis on the AP. Since doing that requires the AP to be turned into an SM, enabling this option will allow you to keep the AP's VLAN configuration in place while the AP is running as an SM.rw Enumeration .1.3.6.1.4.1.161.19.3.1.1.61 |
dhcpRelayAgentEnableEnable or Disable MultiPoint AP acting as DHCP Relay Agent for all SMs and Clients underneath it. (0) - Relay Agent disabled - SM/CPE devices will perform DHCP normally (1) - Relay Agent enabled - AP will intercept DHCP DISCOVER message from SM and CPE, insert Option 82 containing SM's MAC address, and forward request to specified DHCP server.rw Enumeration .1.3.6.1.4.1.161.19.3.1.1.62 |
dhcpRelayAgentSrvrIPObsoleted. Configure with whispApsDNS.dhcprServer.rwobsolete IpAddress .1.3.6.1.4.1.161.19.3.1.1.63 |
colorCodeRescanTimerTime in minutes for the subscriber to begin the idle timer. This timer will begin as soon as a session is started. This only fires if the device is in session with a non-primary color code. A value of zero (0) disables this timer (MultiPoint system Only)rw INTEGER .1.3.6.1.4.1.161.19.3.1.1.64 |
colorCodeRescanIdleTimerTime in minutes for the subscriber to check for an idle state. If an period has pass where no unicast RF traffic has occured (idle), then the subscriber will begin to rescan. This timer will wait until the timer set in colorCodeRescanTimer has expired before beginning. This timer only fires if the device is in session with a non-primary color code. A value of zero (0) mean to rescan without waiting for idle. (MultiPoint system Only)rw INTEGER .1.3.6.1.4.1.161.19.3.1.1.65 |
authKeyOptionAPThis option is for Multipoint APs only. This option will only be used if Authentication Mode is set to AP Pre-Shared Key. 0 - Use default key. 1 - Use set key.rw Enumeration .1.3.6.1.4.1.161.19.3.1.1.66 |
asIP4Obsoleted. Configure with whispApsDNS.authServer4.rwobsolete IpAddress .1.3.6.1.4.1.161.19.3.1.1.67 |
asIP5Obsoleted. Configure with whispApsDNS.authServer5.rwobsolete IpAddress .1.3.6.1.4.1.161.19.3.1.1.68 |
onlyAllowVer95OrAboveOnly allow subscribers that are running version 9.5 or above. Any radio that has a version below 9.5 will not be allowed to register.rw Enumeration .1.3.6.1.4.1.161.19.3.1.1.69 |
apRxDelayThis is used for engineering debug and needs to be removed or moved to eng MIB before releasing the MIB.rw INTEGER .1.3.6.1.4.1.161.19.3.1.1.70 |
qinqEthTypeEtherType for QinQ (802.1ad) outer tag (S-Tag). 0x88a8 by default.rw Enumeration .1.3.6.1.4.1.161.19.3.1.1.71 |
fskSMTxPwrCntlEnable/Disable AP control of SM TX power. For FSK AP radios capable of Transmit Power Control.rw Enumeration .1.3.6.1.4.1.161.19.3.1.1.72 |
fskSMRcvTargetLvlDesired SM Receive Level at AP (dBm, Range -40dBm to -80 dBm).rw INTEGER (-80..-40) UNITS "dBm" .1.3.6.1.4.1.161.19.3.1.1.73 |
authSharedSecret1Authentication Server 1 Shared Secret.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.1.1.74 |
authSharedSecret2Authentication Server 2 Shared Secret.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.1.1.75 |
authSharedSecret3Authentication Server 3 Shared Secret.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.1.1.76 |
whispUsrAuthSharedSecret1Obsoleted. Use whispApsConfig.authSharedSecret1.rwobsolete DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.1.1.79 |
whispUsrAuthSharedSecret2Obsoleted. Use whispApsConfig.authSharedSecret2.rwobsolete DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.1.1.80 |
whispUsrAuthSharedSecret3Obsoleted. Use whispApsConfig.authSharedSecret3.rwobsolete DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.1.1.81 |
whispUsrAcctSvr1Obsoleted. Use whispApsDNS.authServer1.rwobsolete DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.1.1.82 |
whispUsrAcctSvr2Obsoleted. Use whispApsDNS.authServer2.rwobsolete DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.1.1.83 |
whispUsrAcctSvr3Obsoleted. Use whispApsDNS.authServer3.rwobsolete DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.1.1.84 |
whispUsrAuthPhase1Select method for User Authenticationrw Enumeration .1.3.6.1.4.1.161.19.3.1.1.85 |
whispWebUseAuthServerObsoleted. Use whispApsDNS.authServer[1-3].rwobsolete Enumeration .1.3.6.1.4.1.161.19.3.1.1.86 |
dropSessionSM/BHS MAC Address to drop session from the AP/BHM.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.1.1.87 |
uGPSPowerEnable or Disable power supply to Universal GPS module (UGPS capable APs only, when GPS_output_enable is NOT set).rw Enumeration .1.3.6.1.4.1.161.19.3.1.1.88 |
timeZoneSet the timezone offset for the radio. This change takes affect dynamically. The available timezones are: 0 : (UTC) UTC - Coordinated Universal Time 1 : (UTC) GMT - Greenwich Mean Time 2 : (UTC) WET - Western European Time 3 : (UTC-12) BIT - Baker Island Time 4 : (UTC-11) SST - Samoa Standard Time 5 : (UTC-10) CKT - Cook Island Time 6 : (UTC-10) HAST - Hawaii-Aleutian Standard Time 7 : (UTC-10) HST - Hawaii Standard Time 8 : (UTC-10) TAHT - Tahiti Time 9 : (UTC-09:30) MIT - Marquesas Islands Time 10 : (UTC-09) AKST - Alaska Standard Time 11 : (UTC-09) GIT - Gambier Island Time 12 : (UTC-09) HADT - Hawaii-Aleutian Daylight Time 13 : (UTC-08) AKDT - Alaska Daylight Time 14 : (UTC-08) CIST - Clipperton Island Standard Time 15 : (UTC-08) PST - Pacific Standard Time (North America) 16 : (UTC-07) MST - Mountain Standard Time (North America) 17 : (UTC-07) PDT - Pacific Daylight Time (North America) 18 : (UTC-06) CST - Central Standard Time (North America) 19 : (UTC-06) EAST - Easter Island Standard Time 20 : (UTC-06) GALT - Galapagos Time 21 : (UTC-06) MDT - Mountain Daylight Time (North America) 22 : (UTC-05) CDT - Central Daylight Time (North America) 23 : (UTC-05) COT - Colombia Time 24 : (UTC-05) ECT - Ecuador Time 25 : (UTC-05) EST - Eastern Standard Time (North America) 26 : (UTC-04:30) VET - Venezuelan Standard Time 27 : (UTC-04) AST - Atlantic Standard Time 28 : (UTC-04) BOT - Bolivia Time 29 : (UTC-04) CLT - Chile Standard Time 30 : (UTC-04) COST - Colombia Summer Time 31 : (UTC-04) ECT - Eastern Caribbean Time (does not recognise DST) 32 : (UTC-04) EDT - Eastern Daylight Time (North America) 33 : (UTC-04) FKT - Falkland Islands Time 34 : (UTC-04) GYT - Guyana Time 35 : (UTC-03:30) NST - Newfoundland Standard Time 36 : (UTC-03:30) NT - Newfoundland Time 37 : (UTC-03) ADT - Atlantic Daylight Time 38 : (UTC-03) ART - Argentina Time 39 : (UTC-03) BRT - Brasilia Time 40 : (UTC-03) CLST - Chile Summer Time 41 : (UTC-03) FKST - Falkland Islands Summer Time 42 : (UTC-03) GFT - French Guiana Time 43 : (UTC-03) UYT - Uruguay Standard Time 44 : (UTC-02:30) NDT - Newfoundland Daylight Time 45 : (UTC-02) GST - South Georgia and the South Sandwich Islands 46 : (UTC-02) UYST - Uruguay Summer Time 47 : (UTC-01) AZOST - Azores Standard Time 48 : (UTC-01) CVT - Cape Verde Time 49 : (UTC+01) BST - British Summer Time (British Standard Time from Feb 1968 to Oct 1971) 50 : (UTC+01) CET - Central European Time 51 : (UTC+01) DFT - AIX specific equivalent of Central European Time 52 : (UTC+01) IST - Irish Summer Time 53 : (UTC+01) WAT - West Africa Time 54 : (UTC+01) WEDT - Western European Daylight Time 55 : (UTC+01) WEST - Western European Summer Time 56 : (UTC+02) CAT - Central Africa Time 57 : (UTC+02) CEDT - Central European Daylight Time 58 : (UTC+02) CEST - Central European Summer Time 59 : (UTC+02) EET - Eastern European Time 60 : (UTC+02) IST - Israel Standard Time 61 : (UTC+02) SAST - South African Standard Time 62 : (UTC+03) AST - Arab Standard Time (Kuwait, Riyadh) 63 : (UTC+03) AST - Arabic Standard Time (Baghdad) 64 : (UTC+03) EAT - East Africa Time 65 : (UTC+03) EEDT - Eastern European Daylight Time 66 : (UTC+03) EEST - Eastern European Summer Time 67 : (UTC+03) MSK - Moscow Standard Time 68 : (UTC+03:30) IRST - Iran Standard Time 69 : (UTC+04) AMT - Armenia Time 70 : (UTC+04) AST - Arabian Standard Time (Abu Dhabi, Muscat) 71 : (UTC+04) AZT - Azerbaijan Time 72 : (UTC+04) GET - Georgia Standard Time 73 : (UTC+04) MSD - Moscow Summer Time 74 : (UTC+04) MUT - Mauritius Time 75 : (UTC+04) RET - Reunion Time 76 : (UTC+04) SAMT - Samara Time 77 : (UTC+04) SCT - Seychelles Time 78 : (UTC+04:30) AFT - Afghanistan Time 79 : (UTC+05) AMST - Armenia Summer Time 80 : (UTC+05) HMT - Heard and McDonald Islands Time 81 : (UTC+05) PKT - Pakistan Standard Time 82 : (UTC+05) YEKT - Yekaterinburg Time 83 : (UTC+05:30) IST - Indian Standard Time 84 : (UTC+05:30) SLT - Sri Lanka Time 85 : (UTC+05:45) NPT - Nepal Time 86 : (UTC+06) BIOT - British Indian Ocean Time 87 : (UTC+06) BST - Bangladesh Standard Time 88 : (UTC+06) BTT - Bhutan Time 89 : (UTC+06) OMST - Omsk Time 90 : (UTC+06:30) CCT - Cocos Islands Time 91 : (UTC+06:30) MST - Myanmar Standard Time 92 : (UTC+07) CXT - Christmas Island Time 93 : (UTC+07) ICT - Indochina Time 94 : (UTC+07) KRAT - Krasnoyarsk Time 95 : (UTC+07) THA - Thailand Standard Time 96 : (UTC+08) ACT - ASEAN Common Time 97 : (UTC+08) AWST - Australian Western Standard Time 98 : (UTC+08) BDT - Brunei Time 99 : (UTC+08) CST - China Standard Time 100 : (UTC+08) HKT - Hong Kong Time 101 : (UTC+08) IRKT - Irkutsk Time 102 : (UTC+08) MST - Malaysian Standard Time 103 : (UTC+08) PST - Philippine Standard Time 104 : (UTC+08) SST - Singapore Standard Time 105 : (UTC+09) AWDT - Australian Western Daylight Time 106 : (UTC+09) JST - Japan Standard Time 107 : (UTC+09) KST - Korea Standard Time 108 : (UTC+09) YAKT - Yakutsk Time 109 : (UTC+09:30) ACST - Australian Central Standard Time 110 : (UTC+10) AEST - Australian Eastern Standard Time 111 : (UTC+10) ChST - Chamorro Standard Time 112 : (UTC+10) VLAT - Vladivostok Time 113 : (UTC+10:30) ACDT - Australian Central Daylight Time 114 : (UTC+10:30) LHST - Lord Howe Standard Time 115 : (UTC+11) AEDT - Australian Eastern Daylight Time 116 : (UTC+11) MAGT - Magadan Time 117 : (UTC+11) SBT - Solomon Islands Time 118 : (UTC+11:30) NFT - Norfolk Time[1] 119 : (UTC+12) FJT - Fiji Time 120 : (UTC+12) GILT - Gilbert Island Time 121 : (UTC+12) PETT - Kamchatka Time 122 : (UTC+12:45) CHAST - Chatham Standard Time 123 : (UTC+13) PHOT - Phoenix Island Time 124 : (UTC+14) LINT - Line Islands Timerw INTEGER .1.3.6.1.4.1.161.19.3.1.1.89 |
ofdmSMRcvTargetLvlDesired SM Receive Level at AP (dBm, Range -40dBm to -80 dBm). As of release 12.1, on MIMO systems this is a combined power level value.rw INTEGER (-80..-40) UNITS "dBm" .1.3.6.1.4.1.161.19.3.1.1.90 |
radiusPortPort used to connect to the RADIUS server. Default is 1812.rw INTEGER .1.3.6.1.4.1.161.19.3.1.1.91 |
radiusAcctPortPort used to for RADIUS Accounting. Default is 1813.rw INTEGER .1.3.6.1.4.1.161.19.3.1.1.92 |
lastSesStatsResetDisplays the timestamp of last reset of session stats or None otherwise.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.1.1.93 |
resetSesStatsResets the session stats if true.rw Enumeration .1.3.6.1.4.1.161.19.3.1.1.94 |
rfOLTrapEnable/Disable SNMP Trap for when RF Overload exceeds configured Threshold level.rw Enumeration .1.3.6.1.4.1.161.19.3.1.1.95 |
rfOLThresholdPercent of packet overload in the RF Downlink where SNMP is generated and sent to Network Manager.rw INTEGER .1.3.6.1.4.1.161.19.3.1.1.96 |
rfOLEnableEnable/Disable Throughput RF Overload Monitoring monitoring.rw Enumeration .1.3.6.1.4.1.161.19.3.1.1.97 |
actionListFilenameName of the file that contains the Action List for Auto update commands from CNUTrw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.1.1.98 |
enableAutoupdateEnables/Disables auto-update of the SM's under an APrw Enumeration .1.3.6.1.4.1.161.19.3.1.1.99 |
accountingSmReAuthIntervalSelect Interval for Reauthentication of SMrw INTEGER .1.3.6.1.4.1.161.19.3.1.1.100 |
syslogDomainNameAppendThis attribute is deprecated. Use syslogDomainNameAppend in whispBoxAttributesGrouprwdeprecated Enumeration .1.3.6.1.4.1.161.19.3.1.1.101 |
syslogServerAddrThis attribute is deprecated. Use syslogServerAddr in whispBoxAttributesGrouprwdeprecated DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.1.1.102 |
syslogServerPortThis attribute is deprecated. Use syslogServerPort in whispBoxAttributesGrouprw INTEGER .1.3.6.1.4.1.161.19.3.1.1.103 |
syslogXmitAPEnables/Disables transmission of Syslogs from AP/BHMrw Enumeration .1.3.6.1.4.1.161.19.3.1.1.104 |
syslogXmitSMsEnables/Disables transmission of Syslogs from connected SMs/BHS. This can be over-ridden by the setting on individual SMs/ the BHS.rw Enumeration .1.3.6.1.4.1.161.19.3.1.1.105 |
accountingInterimUpdateIntervalSelect Interval for Interim Updatesrw INTEGER .1.3.6.1.4.1.161.19.3.1.1.106 |
gpsOutputEnEnable or Disable GPS sync output enable.rw Enumeration .1.3.6.1.4.1.161.19.3.1.1.107 |
removeIdleSMsSetting this to a value 1 will remove all SMs which are in Idle state from AP's Session list.rw Enumeration .1.3.6.1.4.1.161.19.3.1.1.108 |
lastTimeIdleSMsRemovedDisplays the timestamp of last removal of Idle SMs from AP's Session listro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.1.1.109 |
radioModeThis OID is obsolete.rwobsolete Enumeration .1.3.6.1.4.1.161.19.3.1.1.206 |
rfTelnetAccessAllows/prohibits uplink Telnet access (SM->AP).rw Enumeration .1.3.6.1.4.1.161.19.3.1.1.207 |
upLnkMaxBurstDataRateMaximum burst uplink rate.rw INTEGER UNITS "Kilobits/sec" .1.3.6.1.4.1.161.19.3.1.1.208 |
dwnLnkMaxBurstDataRateMaximum burst downlink rate.rw INTEGER UNITS "Kilobits/sec" .1.3.6.1.4.1.161.19.3.1.1.209 |
rfPPPoEPADIForwardingEnables/disables forwarding of PPPoE PADI packets from AP to SM.rw Enumeration .1.3.6.1.4.1.161.19.3.1.1.210 |
allowedIPAccessNMLength1Length of the network mask to apply to the AllowedIPAddress when assessing if access is allowedrw INTEGER .1.3.6.1.4.1.161.19.3.1.1.211 |
allowedIPAccessNMLength2Length of the network mask to apply to the AllowedIPAddress when assessing if access is allowedrw INTEGER .1.3.6.1.4.1.161.19.3.1.1.212 |
allowedIPAccessNMLength3Length of the network mask to apply to the AllowedIPAddress when assessing if access is allowedrw INTEGER .1.3.6.1.4.1.161.19.3.1.1.213 |
bridgeFloodUnknownsEnableForward unicast packets with an unknown address to all SMs. This can significantly reduce downlink throughput. (0) - Drop unknown unicast packets. (1) - Forward unknown unicast packets to all SMs.rw Enumeration .1.3.6.1.4.1.161.19.3.1.1.214 |
berModSelectThe modulation the AP generates BER at. 0 for QPSK, 1 for 16-QAM, 2 for 64-QAM, and 3 for 256-QAM.rw Enumeration .1.3.6.1.4.1.161.19.3.1.1.215 |
remoteSpectrumAnalyzerScanBandwidthScanning Bandwidth used for the Remote Spectrum Analyzer. Only available on PMP 450.rw Enumeration .1.3.6.1.4.1.161.19.3.1.1.216 |
multicastVCDataRateThe data rate that is used for the Multicast VC. 8X and MIMO-A are currently for engineering only.rw Enumeration .1.3.6.1.4.1.161.19.3.1.1.217 |
dlnkMcastCIRDownlink Multicast CIR (kbps)rw INTEGER .1.3.6.1.4.1.161.19.3.1.1.218 |
multicastRetryCountMulticast Repeat Count : Range 0 - 2. For APs.rw INTEGER .1.3.6.1.4.1.161.19.3.1.1.219 |
apConfigAdjacentChanSupportUsed to enable or disable adjacent channel support.rw Enumeration .1.3.6.1.4.1.161.19.3.1.1.220 |
pmp430InteropModeWhen the AP talks to a PMP 430 it can do so in either MIMO-A or SISO mode. 0 = MIMO-A 1 = SISO Only applies to PMP 450 AP at 5 GHz. By default in 13.2 the AP talks in MIMO-A to PMP 430 SISO SMs. Setting this to a 1 will enable SISO mode to PMP 430 SISO SMs, as it was in 13.1.3 and before.rw Enumeration .1.3.6.1.4.1.161.19.3.1.1.221 |
framePeriodChanges frame period to 2.5 ms or 5ms. Note: If set to 5 ms, only SM/BHS from 13.3 and onward will be able to register. Only on PMP and PTP 450. Not available in all regions.rw Enumeration .1.3.6.1.4.1.161.19.3.1.1.223 |
enableRadiusDynAuthThis option can be used to enable Radius Dynamic Authorization Extensions.Both CoA, which change the SM config parameters from the Radius server while an SM is already in session and Disconnect Message are supported. This option will only be used if Authentication mode is set to Radius AAA. 0 - Disable Radius Dynamic Authorization Extension. 1 - Enable Radius Dynamic Authorization Extension.rw Enumeration .1.3.6.1.4.1.161.19.3.1.1.224 |
pmp430SMRegistrationOption to allow/disallow 430 SMs to register to this AP. When disabled 430 SMs registrations will be rejected. This option applies only to PMP 450i/450 5 GHz APs.rw Enumeration .1.3.6.1.4.1.161.19.3.1.1.225 |
disableAuthForICCSMBypass Authentication for ICC SMsrw Enumeration .1.3.6.1.4.1.161.19.3.1.1.226 |
onlyAllowPMP450iSMRegistrationOption to limit SM registration to only allow PMP 450i devices or allow all devices (450i/450/430) to register. PMP 430 SM registration can be further limited by the pmp430SMRegistration OID if desired. Setting this to only450i will force an Auth Fail registration failure when a PMP 450 or PMP 430 SM device tries to register. This option only applies to PMP 450i AP devices.rw Enumeration .1.3.6.1.4.1.161.19.3.1.1.228 |
pmp450430LegacyModeOption to put the PMP 450i into a Legacy mode for communicating with PMP 450 SMs running SW older than 13.3 and PMP 430 SMs running SW older than 13.4.1. Enabling this option will have an impact on sector throughput performance so should only be enabled to allow upgrading of the mixed sector. This option only applies to PMP 450i AP devices.rw Enumeration .1.3.6.1.4.1.161.19.3.1.1.229 |
pagerRejectFilterSelectEnable or disable the Pager filter which can filter out Pager signals interfering in the 900 MHz band. NOTE: Frequencies 920 MHz and above will not work when enabled. Only applicable to 900 MHz devices.rw Enumeration .1.3.6.1.4.1.161.19.3.1.1.230 |
freeRunGPSSyncBypassEnable to allow Free Run to begin immediately after radio bootup. Normally, Free Run is only allowed after GPS sync has been established at least once, then lost.rw Enumeration .1.3.6.1.4.1.161.19.3.1.1.231 |
useAPManagementVIDForICCSMWhen enabled, SM connected via ICC uses APs MVID instead of its own.rw Enumeration .1.3.6.1.4.1.161.19.3.1.1.232 |
frameAlignmentLegacyModeOption to adjust the frame alignment for compatibility with different GPS sync sources and software versions. Please see user guide for more information. Not applicable to 3 GHz radios running with 5ms frame.rw Enumeration .1.3.6.1.4.1.161.19.3.1.1.233 |
whispApsLink OBJECT IDENTIFIER .1.3.6.1.4.1.161.19.3.1.2 |
whispApsLinkTestConfig OBJECT IDENTIFIER .1.3.6.1.4.1.161.19.3.1.2.1 |
linkTestLUIDLUID selection for Link Test. Valid range: 2-255. [This variable is deprecated, please refer whispBoxLink OIDs]rwdeprecated INTEGER .1.3.6.1.4.1.161.19.3.1.2.1.1 |
linkTestDurationDuration for the Link Test. Valid range: 2-10 seconds. [This variable is deprecated, please refer whispBoxLink OIDs]rwdeprecated INTEGER .1.3.6.1.4.1.161.19.3.1.2.1.2 |
linkTestActionSetting value 1 will initiate link test. Note that trying to set 0 will not stop the test. In fact it will return an error message. The value of 0 just indicates the idle state meaning no test is running or the current test is done. That's why the word stopped is used and not the action verb stop. [This variable is deprecated, please refer whispBoxLink OIDs]rwdeprecated Enumeration .1.3.6.1.4.1.161.19.3.1.2.1.3 |
linkTestPktLengthPacket length for Link Test. Valid range: 64-1714 bytes. [This variable is deprecated, please refer whispBoxLink OIDs]rwdeprecated INTEGER .1.3.6.1.4.1.161.19.3.1.2.1.4 |
linkTestModeLink Test Mode 0 = RF Link Test (traffic doesn't go through bridge, highest throughput) 1 = Link Test with Bridging 2 = Link Test with Bridging and MIR 3 = Extrapolated Link Test (send only a few packets measuring their quality and extrapolate out the throughput) This is an estimation of the throughput based upon the modulation, efficiency, and data slots available. It intended to provide a basic link test test without impacting service for the sector. Extrapolated Link Test is not available for FSK radios. [This Variable is deprecated. Please refer whispBoxLink OIDs]rwdeprecated Enumeration .1.3.6.1.4.1.161.19.3.1.2.1.5 |
linkTestSNRCalculationEnable or disable Signal to Noise Ratio (SNR) calculations during a Link Test. Enabling(1) will calulate SNR on all receiving packets. Due to load on CPU, will slightly degrade packet per second capabilities. Only applicable to GenII OFDM products and up. [This Variable is deprecated. Please refer whispBoxLink OIDs]rwdeprecated Enumeration .1.3.6.1.4.1.161.19.3.1.2.1.6 |
linkTestWithDualPathLink Test with: 0 = Low Priority VC only 1 = High and Low Priority VCs [This variable is deprecated. Please refer whispBoxLink OIDs]rwdeprecated Enumeration .1.3.6.1.4.1.161.19.3.1.2.1.7 |
linkTestNumPktNumber of packets to send. Valid range: 0-64 where 0 will flood the link for the duration of the test. [This variable is deprecated. Please refer whispBoxLink OIDs]rwdeprecated INTEGER .1.3.6.1.4.1.161.19.3.1.2.1.8 |
linkTestForceModulationEngineering use only. Link Test with: 0 = Normal Rate Adapt algorithm 1 = Force to max modultion - No Rate Adapt Algorithm [This variable is deprecated. Please refer whispBoxLink OIDs]rwdeprecated Enumeration .1.3.6.1.4.1.161.19.3.1.2.1.9 |
linkTestDirectionLink Test Direction - Engineering Use Only 0 = default (will do bidirectional) 1 = Uplink Only 2 = Downlink Only 3 = Bi-Directional (same as 0, setting to 3 will result in setting it to 0) [This variable is deprecated. Please refer whispBoxLink OIDs]rwdeprecated Enumeration .1.3.6.1.4.1.161.19.3.1.2.1.10 |
whispApsLinkTestResult OBJECT IDENTIFIER .1.3.6.1.4.1.161.19.3.1.2.2 |
testLUIDLUID number of selected unit. [This variable is deprecated, please refer whispBoxLink OIDs]rodeprecated INTEGER .1.3.6.1.4.1.161.19.3.1.2.2.1 |
linkTestStatusStatus for Link Test.[This variable is deprecated, please refer whispBoxLink OIDs]rodeprecated DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.1.2.2.2 |
linkTestErrorError status of Link Test: (1) Failed to recieve handshake from remote device (2) No session is currently active. Please try again after session established. (3) Received a bad transaction ID. Please try again. (4) We werent able to send the test request to the remote device. (5) We didnt receive any results from the remote device. [This variable is deprecated, please refer whispBoxLink OIDs]rodeprecated DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.1.2.2.3 |
testDurationDuration of link test.[This variable is deprecated, please refer whispBoxLink OIDs]rodeprecated INTEGER .1.3.6.1.4.1.161.19.3.1.2.2.4 |
downLinkRateDownlink Rate.[This variable is deprecated, please refer whispBoxLink OIDs]rodeprecated INTEGER UNITS "bps" .1.3.6.1.4.1.161.19.3.1.2.2.5 |
upLinkRateUplink Rate.[This variable is deprecated, please refer whispBoxLink OIDs]rodeprecated INTEGER UNITS "bps" .1.3.6.1.4.1.161.19.3.1.2.2.6 |
downLinkEffDown Link Efficiency.rodeprecated INTEGER UNITS "%" .1.3.6.1.4.1.161.19.3.1.2.2.7 |
maxDwnLinkIndexFor link test results, the maximum possible downlink efficiency percentage (always 100%).[This variable is deprecated, please refer whispBoxLink OIDs]rodeprecated INTEGER .1.3.6.1.4.1.161.19.3.1.2.2.8 |
actDwnLinkIndexActual down link index.[This variable is deprecated, please refer whispBoxLink OIDs]rodeprecated INTEGER .1.3.6.1.4.1.161.19.3.1.2.2.9 |
expDwnFragCountExpected Fragment Count.[This variable is deprecated, please refer whispBoxLink OIDs]rodeprecated Gauge32 .1.3.6.1.4.1.161.19.3.1.2.2.10 |
actDwnFragCountActual Fragment Count.[This variable is deprecated, please refer whispBoxLink OIDs]rodeprecated Gauge32 .1.3.6.1.4.1.161.19.3.1.2.2.11 |
upLinkEffUp link efficiency.[This variable is deprecated, please refer whispBoxLink OIDs]rodeprecated INTEGER UNITS "%" .1.3.6.1.4.1.161.19.3.1.2.2.12 |
expUpFragCountUplink expected Fragment Count.[This variable is deprecated, please refer whispBoxLink OIDs]rodeprecated Gauge32 .1.3.6.1.4.1.161.19.3.1.2.2.13 |
actUpFragCountActual uplink Fragment Count.[This variable is deprecated, please refer whispBoxLink OIDs]rodeprecated Gauge32 .1.3.6.1.4.1.161.19.3.1.2.2.14 |
maxUpLinkIndexFor link test results, the maximum possible uplink efficiency percentage (always 100%).[This variable is deprecated, please refer whispBoxLink OIDs]rodeprecated INTEGER .1.3.6.1.4.1.161.19.3.1.2.2.15 |
actUpLinkIndexActual Up link index.[This variable is deprecated, please refer whispBoxLink OIDs]rodeprecated INTEGER .1.3.6.1.4.1.161.19.3.1.2.2.16 |
fragments1xDwnLinkVerticalNumber of fragments received on down link at 1X (QPSK). For Gen II OFDM and forward. For MIMO this is the vertical path. [This variable is deprecated, please refer whispBoxLink OIDs]rodeprecated INTEGER .1.3.6.1.4.1.161.19.3.1.2.2.17 |
fragments2xDwnLinkVerticalNumber of fragments received on down link at 2X (16-QAM). For Gen II OFDM and forward. For MIMO this is the vertical path. [This variable is deprecated, please refer whispBoxLink OIDs]rodeprecated INTEGER .1.3.6.1.4.1.161.19.3.1.2.2.18 |
fragments3xDwnLinkVerticalNumber of fragments received on down link at 3X (64-QAM). For Gen II OFDM and forward. For MIMO this is the vertical path. [This variable is deprecated, please refer whispBoxLink OIDs]rodeprecated INTEGER .1.3.6.1.4.1.161.19.3.1.2.2.19 |
fragments4xDwnLinkVerticalNumber of fragments received on down link at 4X (256-QAM). For Gen II OFDM and forward. For MIMO this is the vertical path. [This variable is deprecated, please refer whispBoxLink OIDs]rodeprecated INTEGER .1.3.6.1.4.1.161.19.3.1.2.2.20 |
fragments1xUpLinkVerticalNumber of fragments received on up link at 1X (QPSK). For Gen II OFDM and forward. For MIMO this is the vertical path. [This variable is deprecated, please refer whispBoxLink OIDs]rodeprecated INTEGER .1.3.6.1.4.1.161.19.3.1.2.2.21 |
fragments2xUpLinkVerticalNumber of fragments received on up link at 2X (16-QAM). For Gen II OFDM and forward. For MIMO this is the vertical path. [This variable is deprecated, please refer whispBoxLink OIDs]rodeprecated INTEGER .1.3.6.1.4.1.161.19.3.1.2.2.22 |
fragments3xUpLinkVerticalNumber of fragments received on up link at 3X (64-QAM). For Gen II OFDM and forward. For MIMO this is the vertical path. [This variable is deprecated, please refer whispBoxLink OIDs]rodeprecated INTEGER .1.3.6.1.4.1.161.19.3.1.2.2.23 |
fragments4xUpLinkVerticalNumber of fragments received on up link at 4X (256-QAM). For Gen II OFDM and forward. For MIMO this is the vertical path. [This variable is deprecated, please refer whispBoxLink OIDs]rodeprecated INTEGER .1.3.6.1.4.1.161.19.3.1.2.2.24 |
bitErrorsCorrected1xDwnLinkVerticalNumber of bit errors corrected on average per fragment on down link at 1X (QPSK). For Gen II OFDM and forward. For MIMO this is the vertical path. [This variable is deprecated, please refer whispBoxLink OIDs]rodeprecated DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.1.2.2.25 |
bitErrorsCorrected2xDwnLinkVerticalNumber of bit errors corrected on average per fragment on down link at 2X (16-QAM). For Gen II OFDM and forward. For MIMO this is the vertical path. [This variable is deprecated, please refer whispBoxLink OIDs]rodeprecated DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.1.2.2.26 |
bitErrorsCorrected3xDwnLinkVerticalNumber of bit errors corrected on average per fragment on down link at 3X (64-QAM). For Gen II OFDM and forward. For MIMO this is the vertical path. [This variable is deprecated, please refer whispBoxLink OIDs]rodeprecated DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.1.2.2.27 |
bitErrorsCorrected4xDwnLinkVerticalNumber of bit errors corrected on average per fragment on down link at 4X (256-QAM). For Gen II OFDM and forward. For MIMO this is the vertical path. [This variable is deprecated, please refer whispBoxLink OIDs]rodeprecated DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.1.2.2.28 |
bitErrorsCorrected1xUpLinkVerticalNumber of bit errors corrected on average per fragment on up link at 1X (QPSK). For Gen II OFDM and forward. For MIMO this is the vertical path. [This variable is deprecated, please refer whispBoxLink OIDs]rodeprecated DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.1.2.2.29 |
bitErrorsCorrected2xUpLinkVerticalNumber of bit errors corrected on average per fragment on up link at 2X (16-QAM). For Gen II OFDM and forward. For MIMO this is the vertical path. [This variable is deprecated, please refer whispBoxLink OIDs]rodeprecated DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.1.2.2.30 |
bitErrorsCorrected3xUpLinkVerticalNumber of bit errors corrected on average per fragment on up link at 3X (64-QAM). For Gen II OFDM and forward. For MIMO this is the vertical path. [This variable is deprecated, please refer whispBoxLink OIDs]rodeprecated DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.1.2.2.31 |
bitErrorsCorrected4xUpLinkVerticalNumber of bit errors corrected on average per fragment on up link at 4X (256-QAM). For Gen II OFDM and forward. For MIMO this is the vertical path. [This variable is deprecated, please refer whispBoxLink OIDs]rodeprecated DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.1.2.2.32 |
signalToNoiseRatioDownLinkVerticalEstimated Signal to Noise Ratio in dB for the down link. For Gen II OFDM and forward. For MIMO this is the vertical path. [This variable is deprecated, please refer whispBoxLink OIDs]rodeprecated INTEGER .1.3.6.1.4.1.161.19.3.1.2.2.33 |
signalToNoiseRatioUpLinkVerticalEstimated Signal to Noise Ratio in dB for the up link. For Gen II OFDM and forward. For MIMO this is the vertical path. [This variable is deprecated, please refer whispBoxLink OIDs]rodeprecated INTEGER .1.3.6.1.4.1.161.19.3.1.2.2.34 |
fragments1xDwnLinkHorizontalNumber of fragments received on down link at 1X (QPSK). For MIMO only. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical. [This variable is deprecated, please refer whispBoxLink OIDs]rodeprecated INTEGER .1.3.6.1.4.1.161.19.3.1.2.2.35 |
fragments2xDwnLinkHorizontalNumber of fragments received on down link at 2X (16-QAM). For MIMO only. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical. [This variable is deprecated, please refer whispBoxLink OIDs]rodeprecated INTEGER .1.3.6.1.4.1.161.19.3.1.2.2.36 |
fragments3xDwnLinkHorizontalNumber of fragments received on down link at 3X (64-QAM). For MIMO only. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical. [This variable is deprecated, please refer whispBoxLink OIDs]rodeprecated INTEGER .1.3.6.1.4.1.161.19.3.1.2.2.37 |
fragments4xDwnLinkHorizontalNumber of fragments received on down link at 4X (256-QAM). For MIMO only. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical. [This variable is deprecated, please refer whispBoxLink OIDs]rodeprecated INTEGER .1.3.6.1.4.1.161.19.3.1.2.2.38 |
fragments1xUpLinkHorizontalNumber of fragments received on up link at 1X (QPSK). For MIMO only. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical. [This variable is deprecated, please refer whispBoxLink OIDs]rodeprecated INTEGER .1.3.6.1.4.1.161.19.3.1.2.2.39 |
fragments2xUpLinkHorizontalNumber of fragments received on up link at 2X (16-QAM). For MIMO only. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical. [This variable is deprecated, please refer whispBoxLink OIDs]rodeprecated INTEGER .1.3.6.1.4.1.161.19.3.1.2.2.40 |
fragments3xUpLinkHorizontalNumber of fragments received on up link at 3X (64-QAM). For MIMO only. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical. [This variable is deprecated, please refer whispBoxLink OIDs]rodeprecated INTEGER .1.3.6.1.4.1.161.19.3.1.2.2.41 |
fragments4xUpLinkHorizontalNumber of fragments received on up link at 4X (256-QAM). For MIMO only. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical. [This variable is deprecated, please refer whispBoxLink OIDs]rodeprecated INTEGER .1.3.6.1.4.1.161.19.3.1.2.2.42 |
bitErrorsCorrected1xDwnLinkHorizontalNumber of bit errors corrected on average per fragment on down link at 1X (QPSK). For MIMO and forward. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical. [This variable is deprecated, please refer whispBoxLink OIDs]rodeprecated DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.1.2.2.43 |
bitErrorsCorrected2xDwnLinkHorizontalNumber of bit errors corrected on average per fragment on down link at 2X (16-QAM). For MIMO and forward. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical. [This variable is deprecated, please refer whispBoxLink OIDs]rodeprecated DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.1.2.2.44 |
bitErrorsCorrected3xDwnLinkHorizontalNumber of bit errors corrected on average per fragment on down link at 3X (64-QAM). For MIMO and forward. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical. [This variable is deprecated, please refer whispBoxLink OIDs]rodeprecated DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.1.2.2.45 |
bitErrorsCorrected4xDwnLinkHorizontalNumber of bit errors corrected on average per fragment on down link at 4X (256-QAM). For MIMO and forward. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical. [This variable is deprecated, please refer whispBoxLink OIDs]rodeprecated DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.1.2.2.46 |
bitErrorsCorrected1xUpLinkHorizontalNumber of bit errors corrected on average per fragment on up link at 1X (QPSK). For MIMO and forward. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical. [This variable is deprecated, please refer whispBoxLink OIDs]rodeprecated DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.1.2.2.47 |
bitErrorsCorrected2xUpLinkHorizontalNumber of bit errors corrected on average per fragment on up link at 2X (16-QAM). For MIMO and forward. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical. [This variable is deprecated, please refer whispBoxLink OIDs]rodeprecated DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.1.2.2.48 |
bitErrorsCorrected3xUpLinkHorizontalEngineering use only. Number of bit errors corrected on average per fragment on up link at 3X (64-QAM). For MIMO and forward. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical. [This variable is deprecated, please refer whispBoxLink OIDs]rodeprecated DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.1.2.2.49 |
bitErrorsCorrected4xUpLinkHorizontalNumber of bit errors corrected on average per fragment on up link at 4X (256-QAM). For MIMO and forward. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical. [This variable is deprecated, please refer whispBoxLink OIDs]rodeprecated DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.1.2.2.50 |
signalToNoiseRatioDownLinkHorizontalEstimated Signal to Noise Ratio in dB for the down link. For MIMO and forward. For MIMO this is the horizontal path. If operating in MIMO-A this will return 0. [This variable is deprecated, please refer whispBoxLink OIDs]rodeprecated INTEGER .1.3.6.1.4.1.161.19.3.1.2.2.51 |
signalToNoiseRatioUpLinkHorizontalEstimated Signal to Noise Ratio in dB for the up link. For Gen II OFDM and forward. For MIMO this is the horizontal path. If operating in MIMO-A this will return 0. [This variable is deprecated, please refer whispBoxLink OIDs]rodeprecated INTEGER .1.3.6.1.4.1.161.19.3.1.2.2.52 |
downLinkRateExtrapolatedExtrapolated Downlink Rate from an extrapolated link test. Extrapolated Link Test sends only a few packets over the link and extrapolates this out to what would happen on a full link test. This is an estimation of the throughput based upon the modulation, efficiency, and data slots available. It intended to provide a basic link test test without impacting service for the sector. [This variable is deprecated, please refer whispBoxLink OIDs]rodeprecated INTEGER UNITS "bps" .1.3.6.1.4.1.161.19.3.1.2.2.53 |
upLinkRateExtrapolatedExtrapolated Uplink Rate from an extrapolated link test. Extrapolated Link Test sends only a few packets over the link and extrapolates this out to what would happen on a full link test. This is an estimation of the throughput based upon the modulation, efficiency, and data slots available. It intended to provide a basic link test test without impacting service for the sector. [This variable is deprecated, please refer whispBoxLink OIDs]rodeprecated INTEGER UNITS "bps" .1.3.6.1.4.1.161.19.3.1.2.2.54 |
whispRegStatusThis shows the registration status of a link.[This variable is deprecated, please refer whispBoxLink OIDs]roobsolete DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.1.2.4 |
whispApsGPS OBJECT IDENTIFIER .1.3.6.1.4.1.161.19.3.1.3 |
whispGPSStatsThis shows whether the AP is synchrinized to the GPS timer.ro Enumeration .1.3.6.1.4.1.161.19.3.1.3.1 |
gpsSyncSourceSource of GPS Sync Pulse.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.1.3.2 |
gpsSyncStatusCurrent Live value of Sync Status.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.1.3.3 |
gpsTrackingModeGPS tracking mode.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.1.3.4 |
gpsTimeGPS time.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.1.3.5 |
gpsDateGPS date.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.1.3.6 |
gpsSatellitesTrackedReturns Current number of satellites GPS is tracking in string format .use gpsSatellitesTrackedInt to get the value in integerro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.1.3.7 |
gpsSatellitesVisibleReturn Number of satellites GPS is seeing in string format.Use gpsSatellitesVisibleInt to get value in integerro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.1.3.8 |
gpsHeightGPS height.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.1.3.9 |
gpsAntennaConnectionAntenna Connection status.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.1.3.10 |
gpsLatitudeGPS Latitude.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.1.3.11 |
gpsLongitudeGPS Longitude.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.1.3.12 |
gpsInvalidMsgNumber of invalid messages.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.1.3.13 |
gpsRestartCountNumber of GPS unit restarts.ro INTEGER .1.3.6.1.4.1.161.19.3.1.3.14 |
gpsReInitCountGPS ReInit counts. The number of times we have done a complete re-initialization of the GPS device.ro INTEGER .1.3.6.1.4.1.161.19.3.1.3.15 |
gpsReceiverInfoA textual string contains information on GPS receiver.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.1.3.16 |
gpsFreeRunThis variable is deprecated. Setting this value to false will set AutoSync. Setting this value to true will set AutoSync plus Free Run.rw Enumeration .1.3.6.1.4.1.161.19.3.1.3.17 |
autoSyncStatusCurrent Live value of Sync Status. Following values represent what sources have sync. (0) No Sync (1) On-board GPS Sync (2) Timing Port/UGPS Sync (3) On-board GPS and Timing Port/UGPS Sync (4) Power Port Sync (5) On-board GPS and Power Port Sync (6) Timing Port/UGPS and Power Port Sync (7) On-board GPS, Timing Port/UGPS and Power Port Syncro Enumeration .1.3.6.1.4.1.161.19.3.1.3.18 |
gpsSatellitesTrackedIntCurrent number of satellites GPS is tracking in integer format.ro INTEGER .1.3.6.1.4.1.161.19.3.1.3.19 |
gpsSatellitesVisibleIntNumber of satellites the GPS sees in integer formatro INTEGER .1.3.6.1.4.1.161.19.3.1.3.20 |
whispLinkTableList of link test results SEQUENCE OF WhispLinkEntry .1.3.6.1.4.1.161.19.3.1.4 |
whispLinkEntryList of link test results WhispLinkEntry .1.3.6.1.4.1.161.19.3.1.4.1 |
linkLUIDLUID number.ro INTEGER .1.3.6.1.4.1.161.19.3.1.4.1.1 |
linkDescrA textual string containing information about the unit. This string should include the name of the manufacturer, the product name and the version of the hardware interface.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.1.4.1.2 |
linkPhysAddressPhysical Address of the unit.ro PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.1.4.1.3 |
linkMtuThe size of the largest datagram which can be sent/received on the interface, specified in octets. For interfaces that are used for transmitting network datagrams, this is the size of the largest network datagram that can be sent on the interface.ro INTEGER .1.3.6.1.4.1.161.19.3.1.4.1.4 |
linkSpeedAn estimate of the interface's current bandwidth in bits per second. For interfaces which do not vary in bandwidth or for those where no accurate estimation can be made, this object should contain the nominal bandwidth.ro Gauge32 .1.3.6.1.4.1.161.19.3.1.4.1.5 |
linkOperStatusThis variable is not used.roobsolete Enumeration .1.3.6.1.4.1.161.19.3.1.4.1.6 |
linkInOctetsThe total number of octets received on the interface, including framing characters.ro Counter32 .1.3.6.1.4.1.161.19.3.1.4.1.7 |
linkInUcastPktsThe number of subnetwork-unicast packets delivered to a higher-layer protocol.ro Counter32 .1.3.6.1.4.1.161.19.3.1.4.1.8 |
linkInNUcastPktsThe number of non-unicast (i.e., subnetwork- broadcast or subnetwork-multicast) packets delivered to a higher-layer protocol.ro Counter32 .1.3.6.1.4.1.161.19.3.1.4.1.9 |
linkInDiscardsThe number of inbound packets which were chosen to be discarded even though no errors had been detected to prevent their being deliverable to a higher-layer protocol. One possible reason for discarding such a packet could be to free up buffer space.ro Counter32 .1.3.6.1.4.1.161.19.3.1.4.1.10 |
linkInErrorThe number of inbound packets that contained errors preventing them from being deliverable to a higher-layer protocol.ro Counter32 .1.3.6.1.4.1.161.19.3.1.4.1.11 |
linkInUnknownProtosThe number of packets received via the interface which were discarded because of an unknown or unsupported protocol.ro Counter32 .1.3.6.1.4.1.161.19.3.1.4.1.12 |
linkOutOctetsThe total number of octets transmitted out of the interface, including framing characters.ro Counter32 .1.3.6.1.4.1.161.19.3.1.4.1.13 |
linkOutUcastPktsThe total number of packets that higher-level protocols requested be transmitted to a subnetwork-unicast address, including those that were discarded or not sent.ro Counter32 .1.3.6.1.4.1.161.19.3.1.4.1.14 |
linkOutNUcastPktsThe total number of packets that higher-level protocols requested be transmitted to a non- unicast (i.e., a subnetwork-broadcast or subnetwork-multicast) address, including those that were discarded or not sent.ro Counter32 .1.3.6.1.4.1.161.19.3.1.4.1.15 |
linkOutDiscardsThe number of outbound packets which were chosen to be discarded even though no errors had been detected to prevent their being transmitted. One possible reason for discarding such a packet could be to free up buffer space.ro Counter32 .1.3.6.1.4.1.161.19.3.1.4.1.16 |
linkOutErrorThe number of outbound packets that could not be transmitted because of errors.ro Counter32 .1.3.6.1.4.1.161.19.3.1.4.1.17 |
linkOutQLenNumber of packets in output packet queue.ro Gauge32 .1.3.6.1.4.1.161.19.3.1.4.1.18 |
linkSessStateCurrent operational state of an interface. 0 = Idle 1 = In Session 2 = Clearing 3 = Re-registration downlink reset 4 = Authentication Challenge 5 = Registering 6 = Not in usero Enumeration .1.3.6.1.4.1.161.19.3.1.4.1.19 |
linkESNLink Electronic serial number. It is MAC address.ro PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.1.4.1.20 |
linkRSSIThe average RSSI reading of all packets received from an SM. Applicable to FSK radios only.ro INTEGER .1.3.6.1.4.1.161.19.3.1.4.1.21 |
linkAveJitterThe average Jitter reading of all packets received from an SM. Applicable to FSK radios only.ro Gauge32 .1.3.6.1.4.1.161.19.3.1.4.1.22 |
linkLastJitterLast jitter value. Applicable to FSK radios only.ro Gauge32 .1.3.6.1.4.1.161.19.3.1.4.1.23 |
linkAirDelayThe current round trip air delay in bits measured between the AP and SM.ro INTEGER .1.3.6.1.4.1.161.19.3.1.4.1.24 |
linkRegCountThe number of times an SM has registered to an AP.ro INTEGER .1.3.6.1.4.1.161.19.3.1.4.1.25 |
linkReRegCountThe number of times an SM has tried to register with the AP while it still has an active session with the AP.ro INTEGER .1.3.6.1.4.1.161.19.3.1.4.1.26 |
linkTimeOutLink time out.ro INTEGER .1.3.6.1.4.1.161.19.3.1.4.1.27 |
linkLastRSSIThe last RSSI reading of all packets received from an SM. Applicable to FSK radios only.ro INTEGER .1.3.6.1.4.1.161.19.3.1.4.1.28 |
sessionCountHow many times has this mac been in/out of session.ro INTEGER .1.3.6.1.4.1.161.19.3.1.4.1.29 |
softwareVersionThe software version of registered SM.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.1.4.1.30 |
softwareBootVersionThe software boot version of registered SM.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.1.4.1.31 |
fpgaVersionThe FPGA version of registered SM.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.1.4.1.32 |
linkSiteNameThe site name of the registered SM.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.1.4.1.33 |
avgPowerLevelThe average power level of registered SM. For systems that support power control, this value can read 'NA' when the AP adjusts the transmit power of a SM until new packets are received from the SM with it transmitting at its new power level. For MIMO this is the combined receive power.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.1.4.1.34 |
lastPowerLevelThe last power level of registered SM. For MIMO radios this is the combined receive power.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.1.4.1.35 |
sesDownLinkRateDown link rate.ro INTEGER .1.3.6.1.4.1.161.19.3.1.4.1.36 |
sesDownLinkLimitDown link limit.ro INTEGER .1.3.6.1.4.1.161.19.3.1.4.1.37 |
sesUpLinkRateUplink rate.ro INTEGER .1.3.6.1.4.1.161.19.3.1.4.1.38 |
sesUpLinkLimitUplink limit.ro INTEGER .1.3.6.1.4.1.161.19.3.1.4.1.39 |
adaptRateAdapt rate of registered SM.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.1.4.1.40 |
sesLoUpCIRLow priority up link CIR.ro INTEGER .1.3.6.1.4.1.161.19.3.1.4.1.41 |
sesLoDownCIRLow priority down link CIR.ro INTEGER .1.3.6.1.4.1.161.19.3.1.4.1.42 |
sesHiUpCIRHigh priority up link CIR.ro INTEGER .1.3.6.1.4.1.161.19.3.1.4.1.43 |
sesHiDownCIRHigh priority down link CIR.ro INTEGER .1.3.6.1.4.1.161.19.3.1.4.1.44 |
platformVerPlatform Version.ro INTEGER .1.3.6.1.4.1.161.19.3.1.4.1.45 |
smSessionTmrSM session uptimero TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.161.19.3.1.4.1.46 |
smSessionSeqNumMismatchThe count of how many sequence number mismatch between the AP/BHM and the SM/BHS during the authentication challenge and authentication response messages. This status is only valid in a system where encryption is enabled and no authentication server is configured.ro Counter32 .1.3.6.1.4.1.161.19.3.1.4.1.47 |
dataVCNumThe normal priority Data VC number in use for this link.ro INTEGER .1.3.6.1.4.1.161.19.3.1.4.1.48 |
hiPriQEnReturns whether High Priority channel is enabled. On P7/P8 devices will return 0 always. Use p7p8HiPriQEn OID for P7/P8 radios.ro Enumeration .1.3.6.1.4.1.161.19.3.1.4.1.49 |
dataVCNumHiQThe high priority Data VC number in use for this link, if any. If 0, no High Priority channel is in place.ro INTEGER .1.3.6.1.4.1.161.19.3.1.4.1.50 |
linkInOctetsHiQThe total number of octets received on High Priority Queue, including framing characters.ro Counter32 .1.3.6.1.4.1.161.19.3.1.4.1.51 |
linkInUcastPktsHiQThe number of subnetwork-unicast packets on High Priority Queue delivered to a higher-layer protocol.ro Counter32 .1.3.6.1.4.1.161.19.3.1.4.1.52 |
linkInNUcastPktsHiQThe number of non-unicast (i.e., subnetwork- broadcast or subnetwork-multicast) packets on High Priority Queue delivered to a higher-layer protocol.ro Counter32 .1.3.6.1.4.1.161.19.3.1.4.1.53 |
linkInDiscardsHiQThe number of inbound packets on High Priority Queue which were chosen to be discarded even though no errors had been detected to prevent their being deliverable to a higher-layer protocol. One possible reason for discarding such a packet could be to free up buffer space.ro Counter32 .1.3.6.1.4.1.161.19.3.1.4.1.54 |
linkInErrorHiQThe number of inbound packets on High Priority Queue that contained errors preventing them from being deliverable to a higher-layer protocol.ro Counter32 .1.3.6.1.4.1.161.19.3.1.4.1.55 |
linkInUnknownProtosHiQThe number of packets received on High Priority Queue via the interface which were discarded because of an unknown or unsupported protocol.ro Counter32 .1.3.6.1.4.1.161.19.3.1.4.1.56 |
linkOutOctetsHiQThe total number of octets on High Priority Queue transmitted out of the interface, including framing characters.ro Counter32 .1.3.6.1.4.1.161.19.3.1.4.1.57 |
linkOutUcastPktsHiQThe total number of packets on High Priority Queue that higher-level protocols requested be transmitted to a subnetwork-unicast address, including those that were discarded or not sent.ro Counter32 .1.3.6.1.4.1.161.19.3.1.4.1.58 |
linkOutNUcastPktsHiQThe total number of packets on High Priority Queue that higher-level protocols requested be transmitted to a non- unicast (i.e., a subnetwork-broadcast or subnetwork-multicast) address, including those that were discarded or not sent.ro Counter32 .1.3.6.1.4.1.161.19.3.1.4.1.59 |
linkOutDiscardsHiQThe number of outbound packets on High Priority Queue which were chosen to be discarded even though no errors had been detected to prevent their being transmitted. One possible reason for discarding such a packet could be to free up buffer space.ro Counter32 .1.3.6.1.4.1.161.19.3.1.4.1.60 |
linkOutErrorHiQThe number of outbound packets on High Priority Queue that could not be transmitted because of errors.ro Counter32 .1.3.6.1.4.1.161.19.3.1.4.1.61 |
vcQOverflowThe number of packets dropped due to Queue overflow on VC.ro Counter32 .1.3.6.1.4.1.161.19.3.1.4.1.62 |
vcQOverflowHiQThe number of packets dropped due to Queue overflow on High Priority VC, if enabled.ro Counter32 .1.3.6.1.4.1.161.19.3.1.4.1.63 |
p7p8HiPriQEnReturns whether P7/P8 hi priority channel is enabled. On non-P7/P8 devices will return 0 always.ro Enumeration .1.3.6.1.4.1.161.19.3.1.4.1.64 |
p7p8HiPriQHi Priority Queue statistics for P7 or P8 radios, if enabled. If not enabled, or not a P7 or P8, will return 0.ro Counter32 .1.3.6.1.4.1.161.19.3.1.4.1.65 |
linkAirDelaynsThe current round trip air delay in nanoseconds measured between the AP and SM.ro INTEGER .1.3.6.1.4.1.161.19.3.1.4.1.66 |
linkQualityAPDataEngineering use only. The current link quality of the SM's data from the AP. This is relative to the current modulation rate (1X, 2X, 3X, etc).ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.1.4.1.67 |
linkManagementIPManagement IP Address of the unit. 0 indicates SM is not publically addressable.ro IpAddress .1.3.6.1.4.1.161.19.3.1.4.1.69 |
linkFragmentsReceived1XVerticalEngineering use only. Number of fragments received in 1x (QPSK) modulation. For GenII OFDM and forward. For MIMO this is the vertical path.ro Counter32 .1.3.6.1.4.1.161.19.3.1.4.1.70 |
linkFragmentsReceived2XVerticalEngineering use only. Number of fragments received in 2x (16-QAM) modulation. For GenII OFDM and forward. For MIMO this is the vertical path.ro Counter32 .1.3.6.1.4.1.161.19.3.1.4.1.71 |
linkFragmentsReceived3XVerticalEngineering use only. Number of fragments received in 3x (64-QAM) modulation. For GenII OFDM and forward. For MIMO this is the vertical path.ro Counter32 .1.3.6.1.4.1.161.19.3.1.4.1.72 |
linkFragmentsReceived4XVerticalEngineering use only. Number of fragments received in 4x (256-QAM) modulation. For GenII OFDM and forward. For MIMO this is the vertical path.ro Counter32 .1.3.6.1.4.1.161.19.3.1.4.1.73 |
signalToNoiseRatioVerticalEstimate of the receive signal to noise ratio in dB. For GenII OFDM and forward. For MIMO this is the vertical path.ro INTEGER .1.3.6.1.4.1.161.19.3.1.4.1.74 |
radiusReplyMsgThe RADIUS Reply-Msg populated for the SM. This is only valid when using a backen AAA server.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.1.4.1.75 |
autoUpdateStatusstatus of the auto update processro INTEGER .1.3.6.1.4.1.161.19.3.1.4.1.76 |
radiusFramedIPAddressThis Attribute indicates the IP address to be configured for the SM management interface.ro IpAddress .1.3.6.1.4.1.161.19.3.1.4.1.77 |
radiusFramedIPNetmaskThis Attribute indicates the netmask to be configured for the SM management interface.ro IpAddress .1.3.6.1.4.1.161.19.3.1.4.1.78 |
radiusDefaultGatewayThis Attribute indicates the default gateway to be configured for the SM management interface.ro IpAddress .1.3.6.1.4.1.161.19.3.1.4.1.79 |
linkFragmentsReceived1XHorizontalEngineering use only. Number of fragments received in 1x (QPSK) modulation. For MIMO only. For MIMO this is the horizontal path. If operating in MIMO-A this will return 0.ro Counter32 .1.3.6.1.4.1.161.19.3.1.4.1.80 |
linkFragmentsReceived2XHorizontalEngineering use only. Number of fragments received in 2x (16-QAM) modulation. For MIMO only. For MIMO this is the horizontal path. If operating in MIMO-A this will return 0.ro Counter32 .1.3.6.1.4.1.161.19.3.1.4.1.81 |
linkFragmentsReceived3XHorizontalEngineering use only. Number of fragments received in 3x (64-QAM) modulation. For MIMO only. For MIMO this is the horizontal path. If operating in MIMO-A this will return 0.ro Counter32 .1.3.6.1.4.1.161.19.3.1.4.1.82 |
linkFragmentsReceived4XHorizontalEngineering use only. Number of fragments received in 4x (256-QAM) modulation. For MIMO only. For MIMO this is the horizontal path. If operating in MIMO-A this will return 0.ro Counter32 .1.3.6.1.4.1.161.19.3.1.4.1.83 |
signalToNoiseRatioHorizontalEstimate of the receive signal to noise ratio in dB. MIMO radios only. For MIMO this is the horizontal path. If operating in MIMO-A this will return 0.ro INTEGER .1.3.6.1.4.1.161.19.3.1.4.1.84 |
linkSignalStrengthRatioSignal Strength Ratio in dB is the power received by the vertical antenna input (dB) - power received by the horizontal antenna input (dB). MIMO radios only.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.1.4.1.86 |
linkRadioDbmHorizontalReceive power level of the horizontal antenna in dBm. MIMO radios only.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.1.4.1.87 |
linkRadioDbmVerticalReceive power level of the vertical antenna in dBm. MIMO radios only.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.1.4.1.88 |
maxSMTxPwrReturns whether SM is transmitting at its configured max power level.ro INTEGER .1.3.6.1.4.1.161.19.3.1.4.1.89 |
productTypeReturns which type of product the SM is. PMP 450 APs only.ro Enumeration .1.3.6.1.4.1.161.19.3.1.4.1.90 |
linkAdaptRateLowPriThe current transmitting rate of the low priority VC. 0 : SM is not in session 1 : 1X QPSK SISO 2 : 2X 16-QAM SISO or QPSK MIMO 3 : 3X 64-QAM SISO 4 : 4X 256-QAM SISO or 16-QAM MIMO 6 : 6X 64-QAM MIMO 8 : 8X 256-QAM MIMOro Enumeration .1.3.6.1.4.1.161.19.3.1.4.1.91 |
linkAdaptRateHighPriThe current transmitting rate of the high priority VC. -1 : High Priority Channel not configured 0 : SM is not in session 1 : 1X QPSK SISO 2 : 2X 16-QAM SISO or QPSK MIMO 3 : 3X 64-QAM SISO 4 : 4X 256-QAM SISO or 16-QAM MIMO 6 : 6X 64-QAM MIMO 8 : 8X 256-QAM MIMOro Enumeration .1.3.6.1.4.1.161.19.3.1.4.1.92 |
avgPowerLevelIntThe average power level of registered SM as Integer. For systems that support power control, this value can read '0' when the AP adjusts the transmit power of a SM until new packets are received from the SM with it transmitting at its new power level. For MIMO this is the combined receive power.ro INTEGER .1.3.6.1.4.1.161.19.3.1.4.1.93 |
mimoPowerLevelVerticalFor MIMO radios, the Vertical power level of registered SM as Integer. The Vertical Power (+45) level in case of 2.4GHz Dual slant MIMOro INTEGER .1.3.6.1.4.1.161.19.3.1.4.1.94 |
mimoPowerLevelHorizontalFor MIMO radios, the Horizontal power level of registered SM as Integer. The Horizontal Power(-45) level in case of 2.4GHz Dual slant MIMOro INTEGER .1.3.6.1.4.1.161.19.3.1.4.1.95 |
linkSwVersionThe swversion of registered SM, to be used internally.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.1.4.1.96 |
whispApsEvent OBJECT IDENTIFIER .1.3.6.1.4.1.161.19.3.1.5 |
whispApsRegEvent OBJECT IDENTIFIER .1.3.6.1.4.1.161.19.3.1.5.1 |
whispRegCompleteSignals registration complete. NOTIFICATION-TYPE .1.3.6.1.4.1.161.19.3.1.5.1.1 |
whispRegLostSignals registration lost. NOTIFICATION-TYPE .1.3.6.1.4.1.161.19.3.1.5.1.2 |
whispRegFailureSignals a registration failure has occured. NOTIFICATION-TYPE .1.3.6.1.4.1.161.19.3.1.5.1.3 |
whispDefKeyUsedSignals Default Key used for encryptiont. NOTIFICATION-TYPE .1.3.6.1.4.1.161.19.3.1.5.1.4 |
whispGPSEvent OBJECT IDENTIFIER .1.3.6.1.4.1.161.19.3.1.5.2 |
whispGPSInSyncSignals a transition from not-synchronized to synchronized. NOTIFICATION-TYPE .1.3.6.1.4.1.161.19.3.1.5.2.1 |
whispGPSOutSyncSignals a transition from synchronized to not-synchronized. NOTIFICATION-TYPE .1.3.6.1.4.1.161.19.3.1.5.2.2 |
whispApsDfsEvent OBJECT IDENTIFIER .1.3.6.1.4.1.161.19.3.1.5.3 |
whispRadarDetectedRadar detected transmit stopped. NOTIFICATION-TYPE .1.3.6.1.4.1.161.19.3.1.5.3.1 |
whispRadarEndRadar ended back to normal transmit. NOTIFICATION-TYPE .1.3.6.1.4.1.161.19.3.1.5.3.2 |
whispApRegulatoryEvent OBJECT IDENTIFIER .1.3.6.1.4.1.161.19.3.1.5.4 |
regulatoryApCheckInvalidChanFailedRegulatory Check failed for the unit due to a invalid channel for the configured region. regulatoryStatus - Text description for the failure. physAddress - the MAC address of the unit. NOTIFICATION-TYPE .1.3.6.1.4.1.161.19.3.1.5.4.1 |
regulatoryCheckFailedNoRegionApRegulatory Check failed because a valid region has not be configured. physAddress - the MAC address of the unit. NOTIFICATION-TYPE .1.3.6.1.4.1.161.19.3.1.5.4.2 |
regulatoryApCheckInvalidChBwFailedRegulatory Check failed due to an invalid channel bandwidth for the configured region. regulatoryStatus - Text description for the failure. physAddress - the MAC address of the unit. NOTIFICATION-TYPE .1.3.6.1.4.1.161.19.3.1.5.4.3 |
whispApRFOverloadEvent OBJECT IDENTIFIER .1.3.6.1.4.1.161.19.3.1.5.5 |
rfLinkOverloadConditionAP has exceeded the preset discard percentage in the RF Downlink Direction. rfOutDiscardRate - Current discard Rate. physAddress - the MAC address of the unit. NOTIFICATION-TYPE .1.3.6.1.4.1.161.19.3.1.5.5.1 |
whispApsGroups OBJECT IDENTIFIER .1.3.6.1.4.1.161.19.3.1.6 |
whispLinkTestGroupWHiSP APs link test group. Unknown .1.3.6.1.4.1.161.19.3.1.6.1 |
whispApsConfigGroupWHiSP APs configuration group. Unknown .1.3.6.1.4.1.161.19.3.1.6.2 |
whispApsLinkTableGroupWHiSP APs Link Table group. Unknown .1.3.6.1.4.1.161.19.3.1.6.3 |
whispApsNotifGroupWHiSP APs notification group. Unknown .1.3.6.1.4.1.161.19.3.1.6.4 |
whispApsFailedRegTableGroupWHiSP APs Failed Registration Table group. Unknown .1.3.6.1.4.1.161.19.3.1.6.5 |
whispApsFrUtlStatsIntervalLowGroupWHiSP APs Frame Utilization Statistics group for interval of 1 minute. Only supported for PMP and PTP 450 AP and Backhauls. Unknown .1.3.6.1.4.1.161.19.3.1.6.7 |
whispApsFrUtlStatsIntervalMediumGroupWHiSP APs Frame Utilization Statistics group for interval of 5 minutes. Only supported for PMP and PTP 450 AP and Backhauls. Unknown .1.3.6.1.4.1.161.19.3.1.6.8 |
whispApsFrUtlStatsIntervalHighGroupWHiSP APs Frame Utilization Statistics group for interval of 15 minutes. Only supported for PMP and PTP 450 AP and Backhauls. Unknown .1.3.6.1.4.1.161.19.3.1.6.9 |
whispApsStatus OBJECT IDENTIFIER .1.3.6.1.4.1.161.19.3.1.7 |
regCountNumber of registered SMs.ro Unsigned32 .1.3.6.1.4.1.161.19.3.1.7.1 |
gpsStatusGPS status.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.1.7.2 |
radioSlicingApThe variable is deprecated.roobsolete INTEGER .1.3.6.1.4.1.161.19.3.1.7.3 |
radioTxGainApRadio transmit gain setting.ro INTEGER .1.3.6.1.4.1.161.19.3.1.7.4 |
dataSlotDwnNumber of data slot down.ro INTEGER .1.3.6.1.4.1.161.19.3.1.7.5 |
dataSlotUpNumber of data slot up.ro INTEGER .1.3.6.1.4.1.161.19.3.1.7.6 |
dataSlotUpHiNumber of high priority data slot up.ro Unsigned32 .1.3.6.1.4.1.161.19.3.1.7.7 |
upLnkAckSlotUplink ack slots.ro Unsigned32 .1.3.6.1.4.1.161.19.3.1.7.8 |
upLnkAckSlotHiHige priority uplink ack slots.ro Unsigned32 .1.3.6.1.4.1.161.19.3.1.7.9 |
dwnLnkAckSlotDownlink ack slots.ro Unsigned32 .1.3.6.1.4.1.161.19.3.1.7.10 |
dwnLnkAckSlotHiHige priority downlink ack slots.ro Unsigned32 .1.3.6.1.4.1.161.19.3.1.7.11 |
numCtrSlotNumber of contention slots.ro Unsigned32 .1.3.6.1.4.1.161.19.3.1.7.12 |
numCtrSlotHiHigh priority control slot.ro Unsigned32 .1.3.6.1.4.1.161.19.3.1.7.13 |
dfsStatusDynamic frequency shifting status.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.1.7.14 |
dfsStatusPrimaryDynamic frequency shifting status for Primary Channel.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.1.7.15 |
dfsStatusAlt1Dynamic frequency shifting status for Alternate Channel 1ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.1.7.16 |
dfsStatusAlt2Dynamic frequency shifting status for Alternate Channel 2ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.1.7.17 |
maxRegSMCountMaximum number of unique Subscriber Modules registered with this AP at oncero INTEGER .1.3.6.1.4.1.161.19.3.1.7.18 |
systemTimeDisplays the system time of the unitro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.1.7.19 |
lastNTPTimeDisplays the last NTP time acquired by the APro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.1.7.20 |
regulatoryStatusThe current status of the regulatory check on the AP.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.1.7.21 |
dhcpRlyAgntStat_reqRecvdNumber of DHCP Requests received by the DHCP Relay.ro Counter32 .1.3.6.1.4.1.161.19.3.1.7.22 |
dhcpRlyAgntStat_reqRelayedNumber of DHCP Requests relayed by the DHCP Relay.ro Counter32 .1.3.6.1.4.1.161.19.3.1.7.23 |
dhcpRlyAgntStat_reqDiscardsNumber of DHCP Requests discarded by the DHCP Relay.ro Counter32 .1.3.6.1.4.1.161.19.3.1.7.24 |
dhcpRlyAgntStat_respRecvdNumber of DHCP Replies received by the DHCP Relay.ro Counter32 .1.3.6.1.4.1.161.19.3.1.7.25 |
dhcpRlyAgntStat_respRelayedNumber of DHCP Replies relayed by the DHCP Relay.ro Counter32 .1.3.6.1.4.1.161.19.3.1.7.26 |
dhcpRlyAgntStat_respDiscardsNumber of DHCP Replies discarded by the DHCP Relay.ro Counter32 .1.3.6.1.4.1.161.19.3.1.7.27 |
dhcpRlyAgntStat_untrustedDiscardsNumber of untrusted messages discarded by the DHCP Relay.ro Counter32 .1.3.6.1.4.1.161.19.3.1.7.28 |
dhcpRlyAgntStat_maxHopDiscardsNumber of messages discarded by the DHCP Relay due to exceeded max hop.ro Counter32 .1.3.6.1.4.1.161.19.3.1.7.29 |
dhcpRlyAgntStat_pktTooBigNumber of messages forwarded without relay information by the DHCP Relay due to relay information exceeding max message size.ro Counter32 .1.3.6.1.4.1.161.19.3.1.7.30 |
dhcpRlyAgntStat_invalidGiaddrDiscardsNumber of messages discarded by the DHCP Relay due to invalid giaddr in packet.ro Counter32 .1.3.6.1.4.1.161.19.3.1.7.31 |
regFailureCountThe Total number or Registration Grant Failures.ro Counter32 .1.3.6.1.4.1.161.19.3.1.7.32 |
ntpLogSNMPNTP Logro EventString (WHISP-TCV2-MIB) .1.3.6.1.4.1.161.19.3.1.7.33 |
uGPSPowerStatusCurrent UGPS Power Status (UGPS capable APs only).ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.1.7.34 |
rfOutDiscardRatePercentage of OutDiscards on the RF link (RF Overload %) in the last minute.ro INTEGER .1.3.6.1.4.1.161.19.3.1.7.35 |
autoUpdateGlobalStatusStatus of the Auto-Update Commandro INTEGER .1.3.6.1.4.1.161.19.3.1.7.36 |
currentRadioFreqCarrierReturns the current operating frequency of the AP. Units vary by platform: FSK 5.2, 5.4, 5.7 GHz: OID returns MHz FSK 900 MHz, 2.4 GHz: OID returns 100's of KHz OFDM: OID returns 10's of KHzro INTEGER .1.3.6.1.4.1.161.19.3.1.7.37 |
whispFailedRegTableList of link test results SEQUENCE OF WhispFailedRegEntry .1.3.6.1.4.1.161.19.3.1.8 |
whispFailedRegEntryList of Failed ESNs WhispFailedRegEntry .1.3.6.1.4.1.161.19.3.1.8.1 |
regGrantReasonThe registration failure reasonro Enumeration .1.3.6.1.4.1.161.19.3.1.8.1.1 |
regFailESNThe ESN that failed to registerro PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.1.8.1.2 |
regFailTimeThe number of ticks that occurred when the ESN failed to registerro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.161.19.3.1.8.1.3 |
regFailSeqNumThe sequence when the register failure was given.ro Counter32 .1.3.6.1.4.1.161.19.3.1.8.1.4 |
regFailReasonTextThe text description of the failure.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.1.8.1.5 |
whispApsDNS OBJECT IDENTIFIER .1.3.6.1.4.1.161.19.3.1.9 |
ntpDomainNameAppendSelect whether to append the configured management domain name to the configured trap names. For example, if dnsMgmtDomainName is set to 'example.com', ntpServer is set to 'ntp', and ntpDomainNameAppend is set to appendDomain, the ntpServer name used would be 'ntp.example.com'.rw Enumeration .1.3.6.1.4.1.161.19.3.1.9.1 |
ntpServer1NTP Server 1 Address. Format is either an IP address or DNS name.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.1.9.2 |
ntpServer2NTP Server 2 Address. Format is either an IP address or DNS name.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.1.9.3 |
ntpServer3NTP Server 3 Address. Format is either an IP address or DNS name.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.1.9.4 |
dhcprDomainNameAppendSelect whether to append the configured management domain name to the configured trap names. For example, if dnsMgmtDomainName is set to 'example.com', dhcprServer is set to 'dhcpr', and dhcprDomainNameAppend is set to appendDomain, the dhcprServer name used would be 'dhcpr.example.com'.rw Enumeration .1.3.6.1.4.1.161.19.3.1.9.5 |
dhcprServerDHCP Server IP which will be used for forwarding DHCP messages by the DHCP Relay Agent in the MultiPoint AP. - Format is either an IP address or DNS name. - Default is 255.255.255.255 (broadcast).rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.1.9.6 |
authDomainNameAppendSelect whether to append the configured management domain name to the configured trap names. For example, if dnsMgmtDomainName is set to 'example.com', authServer1 is set to 'auth1', and authDomainNameAppend is set to appendDomain, the authServer1 name used would be 'auth1.example.com'.rw Enumeration .1.3.6.1.4.1.161.19.3.1.9.7 |
authServer1Authentication Server 1. Format is either an IP address or DNS name.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.1.9.8 |
authServer2Authentication Server 2. Format is either an IP address or DNS name.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.1.9.9 |
authServer3Authentication Server 3. Format is either an IP address or DNS name.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.1.9.10 |
authServer4Authentication Server 4. Format is either an IP address or DNS name.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.1.9.11 |
authServer5Authentication Server 5. Format is either an IP address or DNS name.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.1.9.12 |
acctDomainNameAppendObsoleted. Use whispApsDNS.authDomainNameAppend.rwobsolete Enumeration .1.3.6.1.4.1.161.19.3.1.9.13 |
whispApsRFConfig OBJECT IDENTIFIER .1.3.6.1.4.1.161.19.3.1.10 |
whispApsRFConfigRadiosRadio configuration table. SEQUENCE OF WhispApsRFConfigRadioEntry .1.3.6.1.4.1.161.19.3.1.10.1 |
whispApsRFConfigRadioEntryRadio configuration entry. WhispApsRFConfigRadioEntry .1.3.6.1.4.1.161.19.3.1.10.1.1 |
radioFreqCarrierRF Frequency. Please see the whispBoxRFPhysicalRadioFrequencies SNMP table for a list of available frequencies. 0: wired.rw Enumeration .1.3.6.1.4.1.161.19.3.1.10.1.1.1 |
radioDownlinkPercentThis is the percentage of frame data space allocated for downlink. Various radio platforms and regions will have different allowable downlink percentages.rw INTEGER .1.3.6.1.4.1.161.19.3.1.10.1.1.2 |
radioMaxRangeAccess point max range.rw INTEGER UNITS "miles" .1.3.6.1.4.1.161.19.3.1.10.1.1.3 |
radioControlSlotsTotal number of contention slots for HW Scheduling Point-to-Mulitpoint mode (Not applicable for PtoP radios). For PMP 450 the minimum is 1 control slot, others minimum is zero. Maximum contention slots is 15.rw INTEGER .1.3.6.1.4.1.161.19.3.1.10.1.1.4 |
radioTransmitOutputPowerTransmitter output power.rw INTEGER UNITS "dBm" .1.3.6.1.4.1.161.19.3.1.10.1.1.5 |
radioColorCodeColor code.rw INTEGER .1.3.6.1.4.1.161.19.3.1.10.1.1.6 |
whispApsControls OBJECT IDENTIFIER .1.3.6.1.4.1.161.19.3.1.11 |
clearLinkTableStatsSetting this to a nonzero value will clear the link table stats.rw INTEGER .1.3.6.1.4.1.161.19.3.1.11.1 |
whispApsFrUtlStats OBJECT IDENTIFIER .1.3.6.1.4.1.161.19.3.1.12 |
whispApsFrUtlStatsIntervalLow OBJECT IDENTIFIER .1.3.6.1.4.1.161.19.3.1.12.1 |
frUtlLowTotalDownlinkUtilizationPercentage of total downlink utilization in the last 1 minute. Only supported for PMP and PTP 450 AP and Backhauls.ro INTEGER .1.3.6.1.4.1.161.19.3.1.12.1.1 |
frUtlLowTotalUplinkUtilizationPercentage of total uplink utilization in the last 1 minute. Only supported for PMP and PTP 450 AP and Backhauls.ro INTEGER .1.3.6.1.4.1.161.19.3.1.12.1.2 |
frUtlLowTotalDownlinkSlotsTotal downlink data slots in the last 1 minute. Only supported for PMP and PTP 450 AP and Backhauls.ro INTEGER .1.3.6.1.4.1.161.19.3.1.12.1.3 |
frUtlLowDownlinkLowPrioSlotsNumber of data slots used for downlink low priority traffic in the last 1 minute. Only supported for PMP and PTP 450 AP and Backhauls.ro INTEGER .1.3.6.1.4.1.161.19.3.1.12.1.4 |
frUtlLowDownlinkHiPrioSlotsNumber of data slots used for downlink high priority traffic in the last 1 minute. Only supported for PMP and PTP 450 AP and Backhauls.ro INTEGER .1.3.6.1.4.1.161.19.3.1.12.1.5 |
frUtlLowDownlinkBcastSlotsNumber of data slots used for downlink broadcast and multicast traffic in the last 1 minute. Only supported for PMP and PTP 450 AP and Backhauls.ro INTEGER .1.3.6.1.4.1.161.19.3.1.12.1.6 |
frUtlLowDownlinkAckSlotsNumber of data slots used for Downlink Canopy MAC Acknowledgements in the last 1 minute. Only supported for PMP and PTP 450 AP and Backhauls.ro INTEGER .1.3.6.1.4.1.161.19.3.1.12.1.7 |
frUtlLowDownlinkCntlMsgSlotsNumber of data slots used for downlink registration control messages in the last 1 minute. Only supported for PMP and PTP 450 AP and Backhauls.ro INTEGER .1.3.6.1.4.1.161.19.3.1.12.1.8 |
frUtlLowTotalUplinkSlotsTotal uplink data slots in the last 1 minute. Only supported for PMP and PTP 450 AP and Backhauls.ro INTEGER .1.3.6.1.4.1.161.19.3.1.12.1.9 |
frUtlLowUplinkLowPrioSlotsNumber of data slots used for uplink low priority traffic in the last 1 minute. Only supported for PMP and PTP 450 AP and Backhauls.ro INTEGER .1.3.6.1.4.1.161.19.3.1.12.1.10 |
frUtlLowUplinkHiPrioSlotsNumber of data slots used for uplink high priority traffic in the last 1 minute. Only supported for PMP and PTP 450 AP and Backhauls.ro INTEGER .1.3.6.1.4.1.161.19.3.1.12.1.11 |
frUtlLowUplinkAckSlotsNumber of data slots used for Uplink Canopy MAC Acknowledgements in the last 1 minute. Only supported for PMP and PTP 450 AP and Backhauls.ro INTEGER .1.3.6.1.4.1.161.19.3.1.12.1.12 |
frUtlLowMaxDownlinkSlotsMaximum possible downlink data slots for a minute. This is calculated as ((Downlink slots in a frame) * (Number of frames in a second) * 60). Downlink slots in a frame depends on the frame configuration. Number of frames in a second depends on the configured frame period of 5 ms (200 frames) or 2.5 ms (400 frames). Only supported for PMP and PTP 450 AP and Backhauls.ro INTEGER .1.3.6.1.4.1.161.19.3.1.12.1.13 |
frUtlLowMaxUplinkSlotsMaximum possible uplink data slots for a minute. This is calculated as ((Uplink slots in a frame) * (Number of frames in a second) * 60). Uplink slots in a frame depends on the frame configuration. Number of frames in a second depends on the configured frame period of 5 ms (200 frames) or 2.5 ms (400 frames). Only supported for PMP and PTP 450 AP and Backhauls.ro INTEGER .1.3.6.1.4.1.161.19.3.1.12.1.14 |
frUtlLowEthInDiscardsNumber of incoming ethernet packets discarded in the last 1 minute. Only supported for PMP and PTP 450 AP and Backhauls.ro INTEGER .1.3.6.1.4.1.161.19.3.1.12.1.15 |
frUtlLowEthOutDiscardsNumber of outgoing ethernet packets discarded in the last 1 minute. Only supported for PMP and PTP 450 AP and Backhauls.ro INTEGER .1.3.6.1.4.1.161.19.3.1.12.1.16 |
frUtlLowRFInDiscardsNumber of incoming radio packets discarded in the last 1 minute. Only supported for PMP and PTP 450 AP and Backhauls.ro INTEGER .1.3.6.1.4.1.161.19.3.1.12.1.17 |
frUtlLowRFOutDiscardsNumber of outgoing radio packets discarded in the last 1 minute. Only supported for PMP and PTP 450 AP and Backhauls.ro INTEGER .1.3.6.1.4.1.161.19.3.1.12.1.18 |
whispApsFrUtlStatsIntervalMedium OBJECT IDENTIFIER .1.3.6.1.4.1.161.19.3.1.12.2 |
frUtlMedTotalDownlinkUtilizationPercentage of total downlink utilization in the last 5 minutes. Only supported for PMP and PTP 450 AP and Backhauls.ro INTEGER .1.3.6.1.4.1.161.19.3.1.12.2.1 |
frUtlMedTotalUplinkUtilizationPercentage of total uplink utilization in the last 5 minutes. Only supported for PMP and PTP 450 AP and Backhauls.ro INTEGER .1.3.6.1.4.1.161.19.3.1.12.2.2 |
frUtlMedTotalDownlinkSlotsTotal downlink data slots in the last 5 minutes. Only supported for PMP and PTP 450 AP and Backhauls.ro INTEGER .1.3.6.1.4.1.161.19.3.1.12.2.3 |
frUtlMedDownlinkLowPrioSlotsNumber of data slots used for downlink low priority traffic in the last 5 minutes. Only supported for PMP and PTP 450 AP and Backhauls.ro INTEGER .1.3.6.1.4.1.161.19.3.1.12.2.4 |
frUtlMedDownlinkHiPrioSlotsNumber of data slots used for downlink high priority traffic in the last 5 minutes. Only supported for PMP and PTP 450 AP and Backhauls.ro INTEGER .1.3.6.1.4.1.161.19.3.1.12.2.5 |
frUtlMedDownlinkBcastSlotsNumber of data slots used for downlink broadcast and multicast traffic in the last 5 minutes. Only supported for PMP and PTP 450 AP and Backhauls.ro INTEGER .1.3.6.1.4.1.161.19.3.1.12.2.6 |
frUtlMedDownlinkAckSlotsNumber of data slots used for Downlink Canopy MAC Acknowledgements in the last 5 minutes. Only supported for PMP and PTP 450 AP and Backhauls.ro INTEGER .1.3.6.1.4.1.161.19.3.1.12.2.7 |
frUtlMedDownlinkCntlMsgSlotsNumber of data slots used for downlink registration control messages in the last 5 minutes. Only supported for PMP and PTP 450 AP and Backhauls.ro INTEGER .1.3.6.1.4.1.161.19.3.1.12.2.8 |
frUtlMedTotalUplinkSlotsTotal uplink data slots in the last 5 minutes. Only supported for PMP and PTP 450 AP and Backhauls.ro INTEGER .1.3.6.1.4.1.161.19.3.1.12.2.9 |
frUtlMedUplinkLowPrioSlotsNumber of data slots used for uplink low priority traffic in the last 5 minutes. Only supported for PMP and PTP 450 AP and Backhauls.ro INTEGER .1.3.6.1.4.1.161.19.3.1.12.2.10 |
frUtlMedUplinkHiPrioSlotsNumber of data slots used for uplink high priority traffic in the last 5 minutes. Only supported for PMP and PTP 450 AP and Backhauls.ro INTEGER .1.3.6.1.4.1.161.19.3.1.12.2.11 |
frUtlMedUplinkAckSlotsNumber of data slots used for Uplink Canopy MAC Acknowledgements in the last 5 minutes. Only supported for PMP and PTP 450 AP and Backhauls.ro INTEGER .1.3.6.1.4.1.161.19.3.1.12.2.12 |
frUtlMedMaxDownlinkSlotsMaximum possible downlink data slots for 5 minutes. This is calculated as ((Downlink slots in a frame) * (Number of frames in a second) * 5 * 60 (seconds)). Downlink slots in a frame depends on the frame configuration. Number of frames in a second depends on the configured frame period of 5 ms (200 frames) or 2.5 ms (400 frames). Only supported for PMP and PTP 450 AP and Backhauls.ro INTEGER .1.3.6.1.4.1.161.19.3.1.12.2.13 |
frUtlMedMaxUplinkSlotsMaximum possible uplink data slots for 5 minutes. This is calculated as ((Uplink slots in a frame) * (Number of frames in a second) * 5 * 60(seconds)). Uplink slots in a frame depends on the frame configuration. Number of frames in a second depends on the configured frame period of 5 ms (200 frames) or 2.5 ms (400 frames). Only supported for PMP and PTP 450 AP and Backhauls.ro INTEGER .1.3.6.1.4.1.161.19.3.1.12.2.14 |
frUtlMedEthInDiscardsNumber of incoming ethernet packets discarded in the last 5 minutes. Only supported for PMP and PTP 450 AP and Backhauls.ro INTEGER .1.3.6.1.4.1.161.19.3.1.12.2.15 |
frUtlMedEthOutDiscardsNumber of outgoing ethernet packets discarded in the last 5 minutes. Only supported for PMP and PTP 450 AP and Backhauls.ro INTEGER .1.3.6.1.4.1.161.19.3.1.12.2.16 |
frUtlMedRFInDiscardsNumber of incoming radio packets discarded in the last 5 minutes. Only supported for PMP and PTP 450 AP and Backhauls.ro INTEGER .1.3.6.1.4.1.161.19.3.1.12.2.17 |
frUtlMedRFOutDiscardsNumber of outgoing radio packets discarded in the last 5 minutes. Only supported for PMP and PTP 450 AP and Backhauls.ro INTEGER .1.3.6.1.4.1.161.19.3.1.12.2.18 |
whispApsFrUtlStatsIntervalHigh OBJECT IDENTIFIER .1.3.6.1.4.1.161.19.3.1.12.3 |
frUtlHighTotalDownlinkUtilizationPercentage of total downlink utilization in the last 15 minutes. Only supported for PMP and PTP 450 AP and Backhauls.ro INTEGER .1.3.6.1.4.1.161.19.3.1.12.3.1 |
frUtlHighTotalUplinkUtilizationPercentage of total uplink utilization in the last 15 minutes. Only supported for PMP and PTP 450 AP and Backhauls.ro INTEGER .1.3.6.1.4.1.161.19.3.1.12.3.2 |
frUtlHighTotalDownlinkSlotsTotal downlink data slots in the last 15 minutes. Only supported for PMP and PTP 450 AP and Backhauls.ro INTEGER .1.3.6.1.4.1.161.19.3.1.12.3.3 |
frUtlHighDownlinkLowPrioSlotsNumber of data slots used for downlink low priority traffic in the last 15 minutes. Only supported for PMP and PTP 450 AP and Backhauls.ro INTEGER .1.3.6.1.4.1.161.19.3.1.12.3.4 |
frUtlHighDownlinkHiPrioSlotsNumber of data slots used for downlink high priority traffic in the last 15 minutes. Only supported for PMP and PTP 450 AP and Backhauls.ro INTEGER .1.3.6.1.4.1.161.19.3.1.12.3.5 |
frUtlHighDownlinkBcastSlotsNumber of data slots used for downlink broadcast and multicast traffic in the last 15 minutes. Only supported for PMP and PTP 450 AP and Backhauls.ro INTEGER .1.3.6.1.4.1.161.19.3.1.12.3.6 |
frUtlHighDownlinkAckSlotsNumber of data slots used for Downlink Canopy MAC Acknowledgements in the last 15 minutes. Only supported for PMP and PTP 450 AP and Backhauls.ro INTEGER .1.3.6.1.4.1.161.19.3.1.12.3.7 |
frUtlHighDownlinkCntlMsgSlotsNumber of data slots used for downlink registration control messages in the last 15 minutes. Only supported for PMP and PTP 450 AP and Backhauls.ro INTEGER .1.3.6.1.4.1.161.19.3.1.12.3.8 |
frUtlHighTotalUplinkSlotsTotal uplink data slots in the last 15 minutes. Only supported for PMP and PTP 450 AP and Backhauls.ro INTEGER .1.3.6.1.4.1.161.19.3.1.12.3.9 |
frUtlHighUplinkLowPrioSlotsNumber of data slots used for uplink low priority traffic in the last 15 minutes. Only supported for PMP and PTP 450 AP and Backhauls.ro INTEGER .1.3.6.1.4.1.161.19.3.1.12.3.10 |
frUtlHighUplinkHiPrioSlotsNumber of data slots used for uplink high priority traffic in the last 15 minutes. Only supported for PMP and PTP 450 AP and Backhauls.ro INTEGER .1.3.6.1.4.1.161.19.3.1.12.3.11 |
frUtlHighUplinkAckSlotsNumber of data slots used for Uplink Canopy MAC Acknowledgements in the last 15 minutes. Only supported for PMP and PTP 450 AP and Backhauls.ro INTEGER .1.3.6.1.4.1.161.19.3.1.12.3.12 |
frUtlHighMaxDownlinkSlotsMaximum possible downlink data slots for 15 minutes. This is calculated as ((Downlink slots in a frame) * (Number of frames in a second) * 15 * 60(seconds)). Downlink slots in a frame depends on the frame configuration. Number of frames in a second depends on the configured frame period of 5 ms (200 frames) or 2.5 ms (400 frames). Only supported for PMP and PTP 450 AP and Backhauls.ro INTEGER .1.3.6.1.4.1.161.19.3.1.12.3.13 |
frUtlHighMaxUplinkSlotsMaximum possible uplink data slots for 15 minutes. This is calculated as ((Uplink slots in a frame) * (Number of frames in a second) * 15 * 60(seconds)). Uplink slots in a frame depends on the frame configuration. Number of frames in a second depends on the configured frame period of 5 ms (200 frames) or 2.5 ms (400 frames). Only supported for PMP and PTP 450 AP and Backhauls.ro INTEGER .1.3.6.1.4.1.161.19.3.1.12.3.14 |
frUtlHighEthInDiscardsNumber of incoming ethernet packets discarded in the last 15 minutes. Only supported for PMP and PTP 450 AP and Backhauls.ro INTEGER .1.3.6.1.4.1.161.19.3.1.12.3.15 |
frUtlHighEthOutDiscardsNumber of outgoing ethernet packets discarded in the last 15 minutes. Only supported for PMP and PTP 450 AP and Backhauls.ro INTEGER .1.3.6.1.4.1.161.19.3.1.12.3.16 |
frUtlHighRFInDiscardsNumber of incoming radio packets discarded in the last 15 minutes. Only supported for PMP and PTP 450 AP and Backhauls.ro INTEGER .1.3.6.1.4.1.161.19.3.1.12.3.17 |
frUtlHighRFOutDiscardsNumber of outgoing radio packets discarded in the last 15 minutes. Only supported for PMP and PTP 450 AP and Backhauls.ro INTEGER .1.3.6.1.4.1.161.19.3.1.12.3.18 |