WHISP-PLV-MODEM-MIB
Initial Version.
Main OID:
whispPlvModemMIB.1.3.6.1.4.1.161.19.3.7.1
129
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
129 total| Object Name |
|---|
whispPlvModemMIBInitial Version. MODULE-IDENTITY .1.3.6.1.4.1.161.19.3.7.1 |
whispPlvModemObjects OBJECT IDENTIFIER .1.3.6.1.4.1.161.19.3.7.1.1 |
whispPlvModemInfo OBJECT IDENTIFIER .1.3.6.1.4.1.161.19.3.7.1.1.1 |
modemInfoModelThis object indicates the Modem Model Number.ro DisplayString .1.3.6.1.4.1.161.19.3.7.1.1.1.1 |
modemInfoSerialNumberThis object indicates the Modem Serial Number.ro DisplayString .1.3.6.1.4.1.161.19.3.7.1.1.1.2 |
modemInfoDeviceMacThis object indicates the Modem Device MAC Address.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.7.1.1.1.3 |
modemInfoPlcMacThis object indicates the Modem PLC MAC Addressro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.7.1.1.1.4 |
modemInfoHardwareVerThis object indicates the Modem Hardware Version.ro DisplayString .1.3.6.1.4.1.161.19.3.7.1.1.1.5 |
modemInfoDeviceFirmwareVerThis object indicates the Modem Firmware Version.ro DisplayString .1.3.6.1.4.1.161.19.3.7.1.1.1.6 |
modemInfoBootLoaderVerThis object indicates the Modem Boot Loader Version.ro DisplayString .1.3.6.1.4.1.161.19.3.7.1.1.1.7 |
modemInfoSimFirmwareVerThis object indicates the Intellon Simple Module Firmware Version.ro DisplayString .1.3.6.1.4.1.161.19.3.7.1.1.1.8 |
modemInfoDeviceUpgradeStatusThis object indicates the Modems last Software Upgrade Status. 1 - Upgrade not started 2 - Upgrade in progress 3 - Last Upgrade failed 4 - Last Upgrade was successful.ro Enumeration .1.3.6.1.4.1.161.19.3.7.1.1.1.9 |
modemInfoSimUpgradeStatusThis object indicates the Intellon Simple Module Firmware Upgrade Status. 1 - Upgrade not started 2 - Upgrade in progress 3 - Last Upgrade failed 4 - Last Upgrade was successful.ro Enumeration .1.3.6.1.4.1.161.19.3.7.1.1.1.10 |
modemInfoCurrentModeThis object indicates the current operating mode of the Modem. 1 - Bridge Mode 2 - NAT Mode.ro Enumeration .1.3.6.1.4.1.161.19.3.7.1.1.1.11 |
modemInfoActiveBandwidthConfigThis object indicates if the Active Bandwidth settings are either Configured OR Provisioned.ro Enumeration .1.3.6.1.4.1.161.19.3.7.1.1.1.12 |
modemInfoActiveUpLinkBandwidthThis object indicates if the Active Bandwidth settings are either Configured OR Provisioned.ro Enumeration .1.3.6.1.4.1.161.19.3.7.1.1.1.13 |
modemInfoActiveDownLinkBandwidthThis object indicates if the Active Bandwidth settings are either Configured OR Provisioned.ro Enumeration .1.3.6.1.4.1.161.19.3.7.1.1.1.14 |
whispPlvModemConfig OBJECT IDENTIFIER .1.3.6.1.4.1.161.19.3.7.1.1.2 |
modemConfPacketPriorityConfigThis object is used to configure 802.1p Packet Priority type. 1 - Fixed QoS 2 - QoS Based on ToS.rw Enumeration .1.3.6.1.4.1.161.19.3.7.1.1.2.1 |
modemConfFixedQoSConfigThis object is used to configure Fixed QoS type.rw Enumeration .1.3.6.1.4.1.161.19.3.7.1.1.2.2 |
modemConfUpLinkDataRateThis object is used to configure Uplink Data Rate.rw Enumeration .1.3.6.1.4.1.161.19.3.7.1.1.2.3 |
modemConfDownLinkDataRateThis object is used to configure Downlink Data Rate.rw Enumeration .1.3.6.1.4.1.161.19.3.7.1.1.2.4 |
modemConfPSDThis object indicates the Power Spectral Density of the signal, at all the 84 carriers, that the device transmits. Starting at the left most octet, which represents the spectral value at channel number 0, each octet represents the spectral value at the corresponding channel number. The channel numbers 4, 5, 13, 14, 29, 49, 50, 51, 69 and 70 are masked and their spectral values cannot be changed.rw OCTET STRING .1.3.6.1.4.1.161.19.3.7.1.1.2.5 |
modemConfUpLinkMirThis object is used to configure Uplink Maximum Information Rate. This object is for configuring the Data Rate in Kbps, instead of enumerations, as in 'modemConfUpLinkDataRate'. If this object is configured to a Data Rate, which is not supported by the Modem, it will be internally converted to the nearest higher value supported by the Modem. Modem supports only the following Data Rates: 64Kbps, 128Kbps, 256Kbps, 512Kbps, 1Mbps, 4Mbps, 10Mbps and 85Mbps(Full Speed).rw Integer32 UNITS "Kilobits/sec" .1.3.6.1.4.1.161.19.3.7.1.1.2.6 |
modemConfDownLinkMirThis object is used to configure Downlink Maximum Information Rate. This object is for configuring the Data Rate in Kbps, instead of enumerations, as in 'modemConfDownLinkDataRate'. If this object is configured to a Data Rate, which is not supported by the Modem, it will be internally converted to the nearest higher value supported by the Modem. Modem supports only the following Data Rates: 64Kbps, 128Kbps, 256Kbps, 512Kbps, 1Mbps, 4Mbps, 10Mbps and 85Mbps(Full Speed)rw Integer32 UNITS "Kilobits/sec" .1.3.6.1.4.1.161.19.3.7.1.1.2.7 |
whispPlvModemTrapConfig OBJECT IDENTIFIER .1.3.6.1.4.1.161.19.3.7.1.1.3 |
modemConfTrapIp1This object is used to configure IP Address of SNMP Trap Client #1.rw IpAddress .1.3.6.1.4.1.161.19.3.7.1.1.3.1 |
modemConfTrapCommStr1This object is used to configure SNMP CommStrunity string for Trap Client #1.rw DisplayString .1.3.6.1.4.1.161.19.3.7.1.1.3.2 |
modemConfTrapIp2This object is used to configure IP Address of SNMP Trap Client #2.rw IpAddress .1.3.6.1.4.1.161.19.3.7.1.1.3.3 |
modemConfTrapCommStr2This object is used to configure SNMP CommStrunity string for Trap Client #2.rw DisplayString .1.3.6.1.4.1.161.19.3.7.1.1.3.4 |
modemConfTrapIp3This object is used to configure IP Address of SNMP Trap Client #3.rw IpAddress .1.3.6.1.4.1.161.19.3.7.1.1.3.5 |
modemConfTrapCommStr3This object is used to configure SNMP CommStrunity string for Trap Client #3.rw DisplayString .1.3.6.1.4.1.161.19.3.7.1.1.3.6 |
modemConfTrapIp4This object is used to configure IP Address of SNMP Trap Client #4.rw IpAddress .1.3.6.1.4.1.161.19.3.7.1.1.3.7 |
modemConfTrapCommStr4This object is used to configure SNMP CommStrunity string for Trap Client #4.rw DisplayString .1.3.6.1.4.1.161.19.3.7.1.1.3.8 |
modemConfTrapIp5This object is used to configure IP Address of SNMP Trap Client #5.rw IpAddress .1.3.6.1.4.1.161.19.3.7.1.1.3.9 |
modemConfTrapCommStr5This object is used to configure SNMP CommStrunity string for Trap Client #5.rw DisplayString .1.3.6.1.4.1.161.19.3.7.1.1.3.10 |
modemConfTrapIp6This object is used to configure IP Address of SNMP Trap Client #6.rw IpAddress .1.3.6.1.4.1.161.19.3.7.1.1.3.11 |
modemConfTrapCommStr6This object is used to configure SNMP CommStrunity string for Trap Client #6.rw DisplayString .1.3.6.1.4.1.161.19.3.7.1.1.3.12 |
modemConfTrapIp7This object is used to configure IP Address of SNMP Trap Client #7.rw IpAddress .1.3.6.1.4.1.161.19.3.7.1.1.3.13 |
modemConfTrapCommStr7This object is used to configure SNMP CommStrunity string for Trap Client #7.rw DisplayString .1.3.6.1.4.1.161.19.3.7.1.1.3.14 |
modemConfTrapIp8This object is used to configure IP Address of SNMP Trap Client #8.rw IpAddress .1.3.6.1.4.1.161.19.3.7.1.1.3.15 |
modemConfTrapCommStr8This object is used to configure SNMP CommStrunity string for Trap Client #8.rw DisplayString .1.3.6.1.4.1.161.19.3.7.1.1.3.16 |
modemConfTrapIp9This object is used to configure IP Address of SNMP Trap Client #9.rw IpAddress .1.3.6.1.4.1.161.19.3.7.1.1.3.17 |
modemConfTrapCommStr9This object is used to configure SNMP CommStrunity string for Trap Client #9.rw DisplayString .1.3.6.1.4.1.161.19.3.7.1.1.3.18 |
modemConfTrapIp10This object is used to configure IP Address of SNMP Trap Client #10.rw IpAddress .1.3.6.1.4.1.161.19.3.7.1.1.3.19 |
modemConfTrapCommStr10This object is used to configure SNMP CommStrunity string for Trap Client #10.rw DisplayString .1.3.6.1.4.1.161.19.3.7.1.1.3.20 |
whispPlvModemAdmConfig OBJECT IDENTIFIER .1.3.6.1.4.1.161.19.3.7.1.1.4 |
modemAdmConfIpConfigThis object is used to enable or disable the DHCP client, to configure LAN IP Address of the Modem. If the NAT functionality is enabled in the Modem, user will not be able to enable DHCP client to configure the IP address and this object should behave as a read-only object.rw Enumeration .1.3.6.1.4.1.161.19.3.7.1.1.4.1 |
modemAdmConfIpThis object is used to configure IP Address of the Modem. If the NAT functionality is enabled in the Modem, then this object represents the LAN IP Address.rw IpAddress .1.3.6.1.4.1.161.19.3.7.1.1.4.2 |
modemAdmConfIpSubnetMaskThis object is used to configure IP Subnet Mask of the Modem. If the NAT functionality is enabled in the Modem, then this object represents the LAN IP Subnet Mask.rw IpAddress .1.3.6.1.4.1.161.19.3.7.1.1.4.3 |
modemAdmConfNEKThis object is used to configure Network Encryption Key of the Modem.rw DisplayString .1.3.6.1.4.1.161.19.3.7.1.1.4.4 |
modemAdmConfSnmpGetCommStrThis object is used to configure SNMP 'Read' community string of the Modem.rw DisplayString .1.3.6.1.4.1.161.19.3.7.1.1.4.5 |
modemAdmConfSnmpSetCommStrThis object is used to configure SNMP 'Read-Write' community string of the Modem.rw DisplayString .1.3.6.1.4.1.161.19.3.7.1.1.4.6 |
modemAdmConfSnmpAdminCommStrThis object is used to configure SNMP 'Admin' community string of the Modem.rw DisplayString .1.3.6.1.4.1.161.19.3.7.1.1.4.7 |
modemAdmConfLoginUsernameThis object is used to configure Modem's System Management Login Username.rw DisplayString .1.3.6.1.4.1.161.19.3.7.1.1.4.8 |
modemAdmConfLoginPasswordThis object is used to configure Modem's System Management Login Password.rw DisplayString .1.3.6.1.4.1.161.19.3.7.1.1.4.9 |
modemAdmConfFtpServerIpThis object is used to configure IP Address of FTP server hosting auto-upgrade files.rw IpAddress .1.3.6.1.4.1.161.19.3.7.1.1.4.10 |
modemAdmConfFtpUsernameThis object is used to configure Username to login to a FTP server, for use with FTP-based auto-upgrade.rw DisplayString .1.3.6.1.4.1.161.19.3.7.1.1.4.11 |
modemAdmConfFtpPasswordThis object is used to configure Password to login to a FTP server, for use with FTP-based auto-upgrade.rw DisplayString .1.3.6.1.4.1.161.19.3.7.1.1.4.12 |
modemAdmConfFtpFileThis object is used to configure Path and/or Filename of the firmware file, for use with FTP-based auto-upgrade.rw DisplayString .1.3.6.1.4.1.161.19.3.7.1.1.4.13 |
modemAdmConfDeviceUpgradeStartThis object is used to start Firmware Upgrade process in the Modem. To start the upgrade process, this object should be set to '1'.rw Enumeration .1.3.6.1.4.1.161.19.3.7.1.1.4.14 |
modemAdmConfSimUpgradeStartThis object is used to start Intellon Simple Module Firmware Upgrade process. To start the upgrade process, this object should be set to '1'.rw Enumeration .1.3.6.1.4.1.161.19.3.7.1.1.4.15 |
modemAdmConfSystemRebootThis object is used to Reboot the Modem. To reboot the modem, this object should be set to '1'.rw Enumeration .1.3.6.1.4.1.161.19.3.7.1.1.4.16 |
modemAdmConfResetThis object is used to reset the Modem configuration to Factory Defaults. To reset the modem configuration to factory defaults, this object should be set to '1'.rw Enumeration .1.3.6.1.4.1.161.19.3.7.1.1.4.17 |
whispPlvModemAdmWConfig OBJECT IDENTIFIER .1.3.6.1.4.1.161.19.3.7.1.1.5 |
modemAdmWConfNatConfigThis object is used to Enable or Disable the NAT Functionality in the Modem.rw Enumeration .1.3.6.1.4.1.161.19.3.7.1.1.5.1 |
modemAdmWConfWanConfigThis object is used to Enable or Disable DHCP client, to configure the WAN IP Address. This object is accessible only when NAT functionality is enabled in the Modem.rw Enumeration .1.3.6.1.4.1.161.19.3.7.1.1.5.2 |
modemAdmWConfWanIpThis object is used to configure WAN IP Address of the Modem. This object is accessible only when NAT functionality is enabled in the Modem.rw IpAddress .1.3.6.1.4.1.161.19.3.7.1.1.5.3 |
modemAdmWConfSubnetMaskThis object is used to configure WAN IP Subnet Mask of the Modem. This object is accessible only when NAT functionality is enabled in the Modem.rw IpAddress .1.3.6.1.4.1.161.19.3.7.1.1.5.4 |
modemAdmWConfGatewayThis object is used to configure Default Gateway IP of the Modem. This object is accessible only when NAT functionality is enabled in the Modem.rw IpAddress .1.3.6.1.4.1.161.19.3.7.1.1.5.5 |
modemAdmWConfDNS1This object is used to configure DNS Server #1. This object is accessible only when NAT functionality is enabled in the Modem.rw IpAddress .1.3.6.1.4.1.161.19.3.7.1.1.5.6 |
modemAdmWConfDNS2This object is used to configure DNS Server #2. This object is accessible only when NAT functionality is enabled in the Modem.rw IpAddress .1.3.6.1.4.1.161.19.3.7.1.1.5.7 |
modemAdmWConfDhcpConfigThis object is used to Enable or Disable DHCP Server. This object is accessible only when NAT functionality is enabled in the Modem.rw Enumeration .1.3.6.1.4.1.161.19.3.7.1.1.5.8 |
modemAdmWConfDhcpStartIpThis object is used to configure Starting Address of the IP address block, that the DHCP Server can assign to its clients. This object is accessible only when NAT functionality is enabled in the Modem.rw IpAddress .1.3.6.1.4.1.161.19.3.7.1.1.5.9 |
modemAdmWConfDhcpEndIpThis object is used to configure Last Address of the IP address block, that the DHCP Server can assign to its clients. This object is accessible only when NAT functionality is enabled in the Modem.rw IpAddress .1.3.6.1.4.1.161.19.3.7.1.1.5.10 |
modemAdmWConfDhcpLeaseTimeThis object is used to configure time period for which the IP address assigned to a client is valid. This object is accessible only when NAT functionality is enabled in the Modem.rw Enumeration .1.3.6.1.4.1.161.19.3.7.1.1.5.11 |
modemAdmWConfDmzConfigThis object is used to Enable or Disable the DMZ in the MOdem. This object is accessible only when NAT functionality is enabled in the Modem.rw Enumeration .1.3.6.1.4.1.161.19.3.7.1.1.5.12 |
modemAdmWConfDmzIpThis object is used to configure DMZ IP Address of the Modem. This object is accessible only when NAT functionality is enabled in the Modem.rw IpAddress .1.3.6.1.4.1.161.19.3.7.1.1.5.13 |
whispPlvModemAdmSnmpAcessConfig OBJECT IDENTIFIER .1.3.6.1.4.1.161.19.3.7.1.1.6 |
modemAdmSnmpAccessIpNetwork1This object is used to configure SNMP Access Network Address #1.rw IpAddress .1.3.6.1.4.1.161.19.3.7.1.1.6.1 |
modemAdmSnmpAccessIpNetworkMask1This object is used to configure SNMP Access Network Address Mask #1.rw IpAddress .1.3.6.1.4.1.161.19.3.7.1.1.6.2 |
modemAdmSnmpAccessIpNetwork2This object is used to configure SNMP Access Network Address #2.rw IpAddress .1.3.6.1.4.1.161.19.3.7.1.1.6.3 |
modemAdmSnmpAccessIpNetworkMask2This object is used to configure SNMP Access Network Address Mask #2.rw IpAddress .1.3.6.1.4.1.161.19.3.7.1.1.6.4 |
modemAdmSnmpAccessIpNetwork3This object is used to configure SNMP Access Network Address #3.rw IpAddress .1.3.6.1.4.1.161.19.3.7.1.1.6.5 |
modemAdmSnmpAccessIpNetworkMask3This object is used to configure SNMP Access Network Address Mask #3.rw IpAddress .1.3.6.1.4.1.161.19.3.7.1.1.6.6 |
modemAdmSnmpAccessIpNetwork4This object is used to configure SNMP Access Network Address #4.rw IpAddress .1.3.6.1.4.1.161.19.3.7.1.1.6.7 |
modemAdmSnmpAccessIpNetworkMask4This object is used to configure SNMP Access Network Address Mask #4.rw IpAddress .1.3.6.1.4.1.161.19.3.7.1.1.6.8 |
modemAdmSnmpAccessIpNetwork5This object is used to configure SNMP Access Network Address #5.rw IpAddress .1.3.6.1.4.1.161.19.3.7.1.1.6.9 |
modemAdmSnmpAccessIpNetworkMask5This object is used to configure SNMP Access Network Address Mask #5.rw IpAddress .1.3.6.1.4.1.161.19.3.7.1.1.6.10 |
modemAdmSnmpAccessIpNetwork6This object is used to configure SNMP Access Network Address #6.rw IpAddress .1.3.6.1.4.1.161.19.3.7.1.1.6.11 |
modemAdmSnmpAccessIpNetworkMask6This object is used to configure SNMP Access Network Address Mask #6.rw IpAddress .1.3.6.1.4.1.161.19.3.7.1.1.6.12 |
modemAdmSnmpAccessIpNetwork7This object is used to configure SNMP Access Network Address #7.rw IpAddress .1.3.6.1.4.1.161.19.3.7.1.1.6.13 |
modemAdmSnmpAccessIpNetworkMask7This object is used to configure SNMP Access Network Address Mask #7.rw IpAddress .1.3.6.1.4.1.161.19.3.7.1.1.6.14 |
modemAdmSnmpAccessIpNetwork8This object is used to configure SNMP Access Network Address #8.rw IpAddress .1.3.6.1.4.1.161.19.3.7.1.1.6.15 |
modemAdmSnmpAccessIpNetworkMask8This object is used to configure SNMP Access Network Address Mask #8.rw IpAddress .1.3.6.1.4.1.161.19.3.7.1.1.6.16 |
modemAdmSnmpAccessIpNetwork9This object is used to configure SNMP Access Network Address #9.rw IpAddress .1.3.6.1.4.1.161.19.3.7.1.1.6.17 |
modemAdmSnmpAccessIpNetworkMask9This object is used to configure SNMP Access Network Address Mask #9.rw IpAddress .1.3.6.1.4.1.161.19.3.7.1.1.6.18 |
modemAdmSnmpAccessIpNetwork10This object is used to configure SNMP Access Network Address #10.rw IpAddress .1.3.6.1.4.1.161.19.3.7.1.1.6.19 |
modemAdmSnmpAccessIpNetworkMask10This object is used to configure SNMP Access Network Address Mask #10.rw IpAddress .1.3.6.1.4.1.161.19.3.7.1.1.6.20 |
whispPlvModemAdmRepeaterConfig OBJECT IDENTIFIER .1.3.6.1.4.1.161.19.3.7.1.1.7 |
modemAdmRepeaterConfOperatingModeThis object is used to configure the Modem operating mode. Modem should be rebooted for the change in the configuration to take effect.rw Enumeration .1.3.6.1.4.1.161.19.3.7.1.1.7.1 |
modemAdmRepeaterConfModemMAC1This object represents the MAC Address of Modem 1, that uses the Repeater.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.7.1.1.7.2 |
modemAdmRepeaterConfModemMAC2This object represents the MAC Address of Modem 2, that uses the Repeater.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.7.1.1.7.3 |
modemAdmRepeaterConfModemMAC3This object represents the MAC Address of Modem 3, that uses the Repeater.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.7.1.1.7.4 |
modemAdmRepeaterConfModemMAC4This object represents the MAC Address of Modem 4, that uses the Repeater.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.7.1.1.7.5 |
whispPlvModemAdmVLANTableThis table contains one row per device connected behind the Modem, either directly OR using a switch SEQUENCE OF WhispPlvModemAdmVLANEntry .1.3.6.1.4.1.161.19.3.7.1.1.8 |
whispPlvModemAdmVLANEntryVLAN information of the device connected behind the Modem. WhispPlvModemAdmVLANEntry .1.3.6.1.4.1.161.19.3.7.1.1.8.1 |
modemAdmVLANIndexThe value of this object identifies the index to this entry. Integer32 .1.3.6.1.4.1.161.19.3.7.1.1.8.1.1 |
modemAdmVLANPhysAddressThis object indicates the MAC Address of the device connected behind the Modem.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.7.1.1.8.1.2 |
modemAdmVLANIdThis object indicates the VLAN ID of the device connected behind the Modem.rw Integer32 .1.3.6.1.4.1.161.19.3.7.1.1.8.1.3 |
whispPlvModemEvents OBJECT IDENTIFIER .1.3.6.1.4.1.161.19.3.7.1.2 |
modemTrapPrefix OBJECT IDENTIFIER .1.3.6.1.4.1.161.19.3.7.1.2.0 |
modemTrapDeviceUpgradeStartedThis Notification is generated if the Modem has started the firmware Upgrade process. NOTIFICATION-TYPE .1.3.6.1.4.1.161.19.3.7.1.2.0.1 |
modemTrapDeviceUpgradeCompletedThis Notification is generated once the Upgrade process is completed. NOTIFICATION-TYPE .1.3.6.1.4.1.161.19.3.7.1.2.0.2 |
modemTrapSimUpgradeStartedThis Notification is generated if the Intellon Simple Module Upgrade process is started. NOTIFICATION-TYPE .1.3.6.1.4.1.161.19.3.7.1.2.0.3 |
modemTrapSimUpgradeCompletedThis Notification is generated once the Simple Module Upgrade process is completed. NOTIFICATION-TYPE .1.3.6.1.4.1.161.19.3.7.1.2.0.4 |
whispPlvModemConformance OBJECT IDENTIFIER .1.3.6.1.4.1.161.19.3.7.1.3 |
whispPlvModemGroups OBJECT IDENTIFIER .1.3.6.1.4.1.161.19.3.7.1.3.1 |
whispPlvModemInfoGroupThe collection of objects that gives Modem device information. Unknown .1.3.6.1.4.1.161.19.3.7.1.3.1.1 |
whispPlvModemConfigGroupThe collection of objects used to configure the Modem. These objects are accessible to everyone. Unknown .1.3.6.1.4.1.161.19.3.7.1.3.1.2 |
whispPlvModemTrapConfigGroupThe collection of Modems SNMP Trap Configuration objects. These objects are accessible to everyone. Unknown .1.3.6.1.4.1.161.19.3.7.1.3.1.3 |
whispPlvModemAdmConfigGroupThe collection of objects that are used to configure the Modem. These objects are accessible only thru 'admin' community string. Unknown .1.3.6.1.4.1.161.19.3.7.1.3.1.4 |
whispPlvModemAdmWConfigGroupThe collection of Modems WAN Configuration objects. These objects are accessible only thru 'admin' community string. Unknown .1.3.6.1.4.1.161.19.3.7.1.3.1.5 |
whispPlvModemAdmSnmpAcessConfigGroupThe collection of Modems SNMP Access Network objects. These objects are accessible only thru 'admin' community string. Unknown .1.3.6.1.4.1.161.19.3.7.1.3.1.6 |
whispPlvModemNotificationsGroupThe collection of Notifications generated by the Modem. Unknown .1.3.6.1.4.1.161.19.3.7.1.3.1.7 |
whispPlvModemAdmRepeaterConfigGroupThe collection of Repeater Configuration Objects. These objects are accessible only thru 'admin' community string. Unknown .1.3.6.1.4.1.161.19.3.7.1.3.1.8 |
whispPlvModemAdmVLANConfigGroupThe collection of VLAN Configuration Objects. These objects are accessible only thru 'admin' community string. Unknown .1.3.6.1.4.1.161.19.3.7.1.3.1.9 |
whispPlvModemCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.161.19.3.7.1.3.2 |
whispPlvModemComplianceThe compliance statement of SNMP entities which implement the WHISP-PLV-MODEM-MIB. Unknown .1.3.6.1.4.1.161.19.3.7.1.3.2.1 |