WHISP-BOX-MIBV2-MIB
This module contains generic Box-Level MIB definitions for Canopy Radios.
Main OID:
whispBoxLevelMibModule.1.3.6.1.4.1.161.19.1.1.8
635
Objects
Active
Status
5
Dependencies
Imported Objects
Objects
635 total| Object Name |
|---|
whispBoxLevelMibModuleThis module contains generic Box-Level MIB definitions for Canopy Radios. MODULE-IDENTITY .1.3.6.1.4.1.161.19.1.1.8 |
whispBoxStatus OBJECT IDENTIFIER .1.3.6.1.4.1.161.19.3.3.1 |
whispBoxSoftwareVerVersion of software. Should be noted in the event customer has technical difficulties and need to contact technical support.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.1.1 |
whispBoxFPGAVerVersion of FPGA.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.1.2 |
whispBoxEsnElectronic serial number(MAC address) assigned to Radio.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.1.3 |
whispBoxBootSoftware boot version.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.1.4 |
boxTemperatureRadio temperature.roobsolete DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.1.5 |
boxDeviceTypeThe type of the device.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.1.6 |
boxDeviceTypeIDDevice type ID.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.1.7 |
boxEncryptionDevice encryption type.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.1.8 |
etherLinkStatusEthernet link status.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.1.9 |
boxFrequencyFrequency band of the device.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.1.10 |
platformVerHardware platform version. For internal use.ro INTEGER .1.3.6.1.4.1.161.19.3.3.1.11 |
platformTypePlatform type: Canopy, Canopy Lite, Canopy Lite - Advantage, Advantage, Russian, Russian - Advantage.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.1.12 |
dhcpLanIpLAN interface IP obtained through DHCP.ro IpAddress .1.3.6.1.4.1.161.19.3.3.1.13 |
dhcpLanSubnetMaskLAN interface Subnet Mask obtained through DHCP.ro IpAddress .1.3.6.1.4.1.161.19.3.3.1.14 |
dhcpLanGatewayLAN interface Gateway obtained through DHCP.ro IpAddress .1.3.6.1.4.1.161.19.3.3.1.15 |
dhcpRfPublicIpRF Public interface IP obtained through DHCP.ro IpAddress .1.3.6.1.4.1.161.19.3.3.1.16 |
dhcpRfPublicSubnetMaskRF Public interface Subnet Mask obtained through DHCP.ro IpAddress .1.3.6.1.4.1.161.19.3.3.1.17 |
dhcpRfPublicGatewayRF Public interface Gateway obtained through DHCP.ro IpAddress .1.3.6.1.4.1.161.19.3.3.1.18 |
lanDhcpStatusDisplay LAN interface current DHPC status.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.1.19 |
rfPublicDhcpStatusDisplay RF Public interface current DHPC status.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.1.20 |
inSyncCountCounter for number of In Synchronization.ro INTEGER .1.3.6.1.4.1.161.19.3.3.1.21 |
outSyncCountCounter for number of Out of Synchronization.ro INTEGER .1.3.6.1.4.1.161.19.3.3.1.22 |
pllOutLockCountCounter for number of PLL out of Lock.ro INTEGER .1.3.6.1.4.1.161.19.3.3.1.23 |
txCalFailureCounter for number of TX Calibration failure.ro INTEGER .1.3.6.1.4.1.161.19.3.3.1.24 |
swVersionSoftware version information.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.1.25 |
pldVersionPLD version information.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.1.26 |
platformInfoPlatform information.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.1.27 |
antPolarizationAntenna polarization for FSK radios.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.1.28 |
packetOverloadCounterTotal packet overload count.ro Counter32 .1.3.6.1.4.1.161.19.3.3.1.29 |
whispBoxP11PersonalityBoard Personality Configuration of P11 and P12 radios.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.1.30 |
whispBoxP11FPGATypeFPGA Type on P11 and P12 radios.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.1.31 |
whispBoxP11BstrapFPGAVerP11 Bootstrap FPGA Version.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.1.32 |
numDFSDetectionsNumber of DFS Detections since last boot.ro Counter32 .1.3.6.1.4.1.161.19.3.3.1.33 |
rxOverrunPktsCounter for number of received overrun packets error.ro Counter32 .1.3.6.1.4.1.161.19.3.3.1.34 |
boxTemperatureCRadio temperature in Celsius.ro INTEGER .1.3.6.1.4.1.161.19.3.3.1.35 |
boxTemperatureFRadio temperature in Fahrenheit.ro INTEGER .1.3.6.1.4.1.161.19.3.3.1.36 |
bridgeCbFecStatbinBridge CB FEC Stats binro Counter32 .1.3.6.1.4.1.161.19.3.3.1.37 |
bridgeCbFecStatboutBridge CB FEC Stats boutro Counter32 .1.3.6.1.4.1.161.19.3.3.1.38 |
bridgeCbFecStatbtossBridge CB FEC Stats btossro Counter32 .1.3.6.1.4.1.161.19.3.3.1.39 |
bridgeCbFecStatbtosscapBridge CB FEC Stats btosscapro Counter32 .1.3.6.1.4.1.161.19.3.3.1.40 |
bridgeCbFecStatuinBridge CB FEC Stats uinro Counter32 .1.3.6.1.4.1.161.19.3.3.1.41 |
bridgeCbFecStatuoutBridge CB FEC Stats uoutro Counter32 .1.3.6.1.4.1.161.19.3.3.1.42 |
bridgeCbFecStatutossBridge CB FEC Stats utossro Counter32 .1.3.6.1.4.1.161.19.3.3.1.43 |
bridgeCbFecStatutosscapBridge CB FEC Stats utosscapro Counter32 .1.3.6.1.4.1.161.19.3.3.1.44 |
bridgeCbRFStatbinBridge CB RF Stats binro Counter32 .1.3.6.1.4.1.161.19.3.3.1.45 |
bridgeCbRFStatboutBridge CB RF Stats boutro Counter32 .1.3.6.1.4.1.161.19.3.3.1.46 |
bridgeCbRFStatbtossBridge CB RF Stats btossro Counter32 .1.3.6.1.4.1.161.19.3.3.1.47 |
bridgeCbRFStatbtosscapBridge CB RF Stats btosscapro Counter32 .1.3.6.1.4.1.161.19.3.3.1.48 |
bridgeCbRFStatuinBridge CB RF Stats uinro Counter32 .1.3.6.1.4.1.161.19.3.3.1.49 |
bridgeCbRFStatuoutBridge CB RF Stats uoutro Counter32 .1.3.6.1.4.1.161.19.3.3.1.50 |
bridgeCbRFStatutossBridge CB RF Stats utossro Counter32 .1.3.6.1.4.1.161.19.3.3.1.51 |
bridgeCbRFStatutosscapBridge CB RF Stats utosscapro Counter32 .1.3.6.1.4.1.161.19.3.3.1.52 |
bridgeCbErrStatNI1QSendBridge CB Error Stats ErrNI1QSendro Counter32 .1.3.6.1.4.1.161.19.3.3.1.53 |
bridgeCbErrStatNI2QSendBridge CB Error Stats ErrNI2QSendro Counter32 .1.3.6.1.4.1.161.19.3.3.1.54 |
bridgeCbErrStatBridgeFullBridge CB Error Stats BridgeFullro Counter32 .1.3.6.1.4.1.161.19.3.3.1.55 |
bridgeCbErrStatSendMsgBridge CB Error Stats SendMsgro Counter32 .1.3.6.1.4.1.161.19.3.3.1.56 |
bridgeCbErrStatAPFecQSendBridge CB Error Stats APFecQSendro Counter32 .1.3.6.1.4.1.161.19.3.3.1.57 |
bridgeCbErrStatApRfQSendBridge CB Error Stats ApRfQSendro Counter32 .1.3.6.1.4.1.161.19.3.3.1.58 |
rfStatXmtUDataCntRF Scheduler Stats Transmit Unicast Data Countro Counter32 .1.3.6.1.4.1.161.19.3.3.1.59 |
rfStatXmtBDataCntRF Scheduler Stats Transmit Broadcast Data Countro Counter32 .1.3.6.1.4.1.161.19.3.3.1.60 |
rfStatRcvUDataCntRF Scheduler Stats Receive Unicast Data Countro Counter32 .1.3.6.1.4.1.161.19.3.3.1.61 |
rfStatRcvBDataCntRF Scheduler Stats Receive Broadcast Data Countro Counter32 .1.3.6.1.4.1.161.19.3.3.1.62 |
rfStatXmtCntlCntRF Scheduler Stats Transmit Control Countro Counter32 .1.3.6.1.4.1.161.19.3.3.1.63 |
rfStatRcvCntlCntRF Scheduler Stats Receive Control Countro Counter32 .1.3.6.1.4.1.161.19.3.3.1.64 |
rfStatInSyncCountRF Scheduler Stats In Sync Countro Counter32 .1.3.6.1.4.1.161.19.3.3.1.65 |
rfStatOutSyncCountRF Scheduler Stats Out Sync Countro Counter32 .1.3.6.1.4.1.161.19.3.3.1.66 |
rfStatOverrunCountRF Scheduler Stats Overrun Countro Counter32 .1.3.6.1.4.1.161.19.3.3.1.67 |
rfStatUnderrunCountRF Scheduler Stats Underrun Countro Counter32 .1.3.6.1.4.1.161.19.3.3.1.68 |
rfStatRcvCorruptDataCountRF Scheduler Stats Receive Corrupt Data Countro Counter32 .1.3.6.1.4.1.161.19.3.3.1.69 |
rfStatBadBcastCtlCntRF Scheduler Stats Bad Broadcast Control Countro Counter32 .1.3.6.1.4.1.161.19.3.3.1.70 |
rfStatPLLOutOfLockCntRF Scheduler Stats PLL Out of Lock Countro Counter32 .1.3.6.1.4.1.161.19.3.3.1.71 |
rfStatBeaconVerMismatchCntRF Scheduler Stats Beacon version Mismatch Countro Counter32 .1.3.6.1.4.1.161.19.3.3.1.72 |
rfStatBadFreqBcnRcvCntRF Scheduler Stats Wrong Frequency Beacon Received Countro Counter32 .1.3.6.1.4.1.161.19.3.3.1.73 |
rfStatnonLiteBcnRcvCntRF Scheduler Stats Non Lite Beacon Received Countro Counter32 .1.3.6.1.4.1.161.19.3.3.1.74 |
rfStatUnsupFeatBcnRcvCntRF Scheduler Stats Unsupported Feature Beacon Received Countro Counter32 .1.3.6.1.4.1.161.19.3.3.1.75 |
rfStatUnkwnFeatBcnRcvCntRF Scheduler Stats Unknown Feature Beacon Received Countro Counter32 .1.3.6.1.4.1.161.19.3.3.1.76 |
rfStatTxCalFailCntRF Scheduler Stats TX Calibration Failures Countro Counter32 .1.3.6.1.4.1.161.19.3.3.1.77 |
rfStatBadInSyncIDRcvRF Scheduler Stats Bad In Sync ID Received Countro Counter32 .1.3.6.1.4.1.161.19.3.3.1.78 |
rfStatTempOutOfRangeRF Scheduler Stats Temperature Out of Range Countro Counter32 .1.3.6.1.4.1.161.19.3.3.1.79 |
rfStatRSSIOutOfRangeRF Scheduler Stats RSSI Out of Range Countro Counter32 .1.3.6.1.4.1.161.19.3.3.1.80 |
rfStatRangeCapEnfRF Scheduler Stats Range Cap Enforced Countro Counter32 .1.3.6.1.4.1.161.19.3.3.1.81 |
rfStatRcvLTStartRF Scheduler Stats Rcv LT Start Countro Counter32 .1.3.6.1.4.1.161.19.3.3.1.82 |
rfStatRcvLTStartHSRF Scheduler Stats Rcv LT Start HS Countro Counter32 .1.3.6.1.4.1.161.19.3.3.1.83 |
rfStatRcvLTResultRF Scheduler Stats Rcv LT Result Countro Counter32 .1.3.6.1.4.1.161.19.3.3.1.84 |
rfStatXmtLTResultRF Scheduler Stats Xmt LT Result Countro Counter32 .1.3.6.1.4.1.161.19.3.3.1.85 |
whispFeatureKeyOriginOrigin of Feature Key which includes GMT time and location of the Key programming (if time is 0 the key was converted locally)ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.1.86 |
radioMSNMSN of the radio.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.1.87 |
updateStatusCurrent Status of Device Updatero INTEGER .1.3.6.1.4.1.161.19.3.3.1.88 |
syslogStatTxSuccessesThe count of Syslog messages sent to UDP layer.ro INTEGER .1.3.6.1.4.1.161.19.3.3.1.89 |
syslogStatDroppedNumber of dropped syslog messages due to device overload and/or resource limitations.ro INTEGER .1.3.6.1.4.1.161.19.3.3.1.90 |
fecStatLinkLostEthernet link lost countro Counter32 .1.3.6.1.4.1.161.19.3.3.1.91 |
fecStatLinkDetectedEthernet link detected countro Counter32 .1.3.6.1.4.1.161.19.3.3.1.92 |
natDhcpStatusDisplay NAT Public interface current DHPC status.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.1.93 |
fecInDiscardsCountEthernet in discards count.ro Unsigned32 .1.3.6.1.4.1.161.19.3.3.1.94 |
fecInErrorsCountEthernet in errors count.ro Unsigned32 .1.3.6.1.4.1.161.19.3.3.1.95 |
fecOutDiscardsCountEthernet out discards count.ro Unsigned32 .1.3.6.1.4.1.161.19.3.3.1.96 |
fecOutErrorsCountEthernet out errors count.ro Unsigned32 .1.3.6.1.4.1.161.19.3.3.1.97 |
rfInDiscardsCountRF in discards count.ro Unsigned32 .1.3.6.1.4.1.161.19.3.3.1.98 |
rfInErrorsCountRF in errors count.ro Unsigned32 .1.3.6.1.4.1.161.19.3.3.1.99 |
rfOutDiscardsCountRF out discards count.ro Unsigned32 .1.3.6.1.4.1.161.19.3.3.1.100 |
rfOutErrorsCountRF out errors count.ro Unsigned32 .1.3.6.1.4.1.161.19.3.3.1.101 |
fecInDiscardsOverloadCountEthernet in discards overload.ro Counter32 .1.3.6.1.4.1.161.19.3.3.1.102 |
fecOutDiscardsOverloadCountEthernet out discards overload.ro Counter32 .1.3.6.1.4.1.161.19.3.3.1.103 |
rfInDiscardsOverloadCountRf in discards overload.ro Counter32 .1.3.6.1.4.1.161.19.3.3.1.104 |
rfOutDiscardsOverloadCountRf out discards overload.ro Counter32 .1.3.6.1.4.1.161.19.3.3.1.105 |
fpgaCompileInfoDisplay the fpga compiled attributes. (Engineering Only)ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.1.106 |
fpgaBuildDateDisplay the entire fpga build date string. (Engineering Only)ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.1.107 |
aggregateBandwidthCapThe maximum aggregate (uplink + downlink) the radio is capable of.ro INTEGER .1.3.6.1.4.1.161.19.3.3.1.108 |
calibrationStatusBoolBoolean OID to show if device is calibrated. Applicable to FSK and MIMO radios only.ro Enumeration .1.3.6.1.4.1.161.19.3.3.1.109 |
calibrationStatusBoxString to show if radio is calibrated. Applicable to FSK and MIMO radios only.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.1.110 |
radioEngKeyedThis will be set either as 0 if the engineering key patch is not applied to the radio or 1 if it is applied.ro INTEGER .1.3.6.1.4.1.161.19.3.3.1.111 |
bridgeCbFecStatfloodsBridge CB RF Stats Floods (Multipoint AP only)ro Counter32 .1.3.6.1.4.1.161.19.3.3.1.112 |
bridgeCbRFStatfloodsBridge CB RF Stats Floods (Multipoint AP only)ro Counter32 .1.3.6.1.4.1.161.19.3.3.1.113 |
catalinaGainRxCH1Rcv Gain on Catalina Rx CH1. Engineering use only.ro INTEGER .1.3.6.1.4.1.161.19.3.3.1.114 |
catalinaGainRxCH2Rcv Gain on Catalina Rx CH2. Engineering use only.ro INTEGER .1.3.6.1.4.1.161.19.3.3.1.115 |
antTypeIndicates whether the antenna is integrated or external (connectorized).ro Enumeration .1.3.6.1.4.1.161.19.3.3.1.116 |
rfStatRcvCorruptControlCountRF Scheduler Stats Receive Corrupt Control Data Countro Counter32 .1.3.6.1.4.1.161.19.3.3.1.117 |
numLBTDetectionsNumber of LBT Detections since last boot.ro Counter32 .1.3.6.1.4.1.161.19.3.3.1.118 |
catalinaAttenTxCH1Attenuation on Catalina Tx CH1. Engineering Use Only.ro INTEGER .1.3.6.1.4.1.161.19.3.3.1.121 |
catalinaAttenTxCH2Attenuation on Catalina Tx CH2. Engineering use only.ro INTEGER .1.3.6.1.4.1.161.19.3.3.1.122 |
catalinaCurrDetSetpointTxCH1Current Detector Setpoint on Catalina Tx CH1. Engineering Use Only.ro INTEGER .1.3.6.1.4.1.161.19.3.3.1.123 |
catalinaCurrDetSetpointTxCH2Current Detector Setpoint on Catalina Tx CH2. Engineering use only.ro INTEGER .1.3.6.1.4.1.161.19.3.3.1.124 |
catalinaCurrDetReadRefTxCH1Current Detector Reference on Catalina Tx CH1. Engineering Use Only.ro INTEGER .1.3.6.1.4.1.161.19.3.3.1.125 |
catalinaCurrDetReadRefTxCH2Current Detector Reference on Catalina Tx CH2. Engineering use only.ro INTEGER .1.3.6.1.4.1.161.19.3.3.1.126 |
catalinaCurrDetReadPowerOnTxCH1Current Detector PowerOn on Catalina Tx CH1. Engineering Use Only.ro INTEGER .1.3.6.1.4.1.161.19.3.3.1.127 |
catalinaCurrDetReadPowerOnTxCH2Current Detector PowerOn on Catalina Tx CH2. Engineering use only.ro INTEGER .1.3.6.1.4.1.161.19.3.3.1.128 |
catalinaOpenLoopAttenTxCH1Open Loop Attenuation on Catalina Tx CH1. Engineering Use Only.ro INTEGER .1.3.6.1.4.1.161.19.3.3.1.129 |
catalinaOpenLoopAttenTxCH2Open Loop Attenuation on Catalina Tx CH2. Engineering use only.ro INTEGER .1.3.6.1.4.1.161.19.3.3.1.130 |
catalinaTargetDetSetpointTxCH1Target Detector Setpoint on Catalina Tx CH1. Engineering Use Only.ro INTEGER .1.3.6.1.4.1.161.19.3.3.1.131 |
catalinaTargetDetSetpointTxCH2Target Detector Setpoint on Catalina Tx CH2. Engineering use only.ro INTEGER .1.3.6.1.4.1.161.19.3.3.1.132 |
catalinaGainReductionRxCH1Gain Reduction on Catalina Rx CH1. Engineering Use Only.ro INTEGER .1.3.6.1.4.1.161.19.3.3.1.133 |
catalinaGainReductionRxCH2Gain Reduction on Catalina Rx CH2. Engineering use only.ro INTEGER .1.3.6.1.4.1.161.19.3.3.1.134 |
catalinaLoAttenRxCH1Lo Attenuation on Catalina Rx CH1. Engineering Use Only.ro INTEGER .1.3.6.1.4.1.161.19.3.3.1.135 |
catalinaLoAttenRxCH2Lo Attenuation on Catalina Rx CH2. Engineering use only.ro INTEGER .1.3.6.1.4.1.161.19.3.3.1.136 |
catalinaTargetGainRxCH1Target Gain on Catalina Rx CH1. Engineering Use Only.ro INTEGER .1.3.6.1.4.1.161.19.3.3.1.137 |
catalinaTargetGainRxCH2Target Gain on Catalina Rx CH2. Engineering use only.ro INTEGER .1.3.6.1.4.1.161.19.3.3.1.138 |
radioWatchDogLoggedThis will be set either as 0 if there is no watchdog event logged or 1 if there is.ro INTEGER .1.3.6.1.4.1.161.19.3.3.1.147 |
radioFatalErrorLoggedThis will be set either as 0 if there is no fatalerror event logged or 1 if there is.ro INTEGER .1.3.6.1.4.1.161.19.3.3.1.148 |
rfStatXmtMDataCntRF Scheduler Stats Transmit Multicast Data Countro Counter32 .1.3.6.1.4.1.161.19.3.3.1.217 |
rfStatRcvMDataCntRF Scheduler Stats Receive Multicast Data Countro Counter32 .1.3.6.1.4.1.161.19.3.3.1.218 |
fecStatUnderSizedTossUndersized Toss Countro Counter32 .1.3.6.1.4.1.161.19.3.3.1.219 |
fecRxBabErrError count in Babble Receiver.ro Counter32 .1.3.6.1.4.1.161.19.3.3.1.220 |
fecTxHbErrNumber of packets having Transmit heartbeat error.ro Counter32 .1.3.6.1.4.1.161.19.3.3.1.221 |
fecEthBusErrEthernet Busy Error Countro Counter32 .1.3.6.1.4.1.161.19.3.3.1.222 |
fecCRCErrorNumber of packets having CRC Error.ro Counter32 .1.3.6.1.4.1.161.19.3.3.1.223 |
fecRxFifoNoBufNumber of times could not get a buffer from Rx Fifo.ro Counter32 .1.3.6.1.4.1.161.19.3.3.1.224 |
fecRxOverrunNumber of times Rx Fifo Overrun.ro Counter32 .1.3.6.1.4.1.161.19.3.3.1.225 |
fecLateCollisionNumber of packets having late collision.ro Counter32 .1.3.6.1.4.1.161.19.3.3.1.226 |
fecRetransLimitExpNumber of packets whose retransmision limit expired.ro Counter32 .1.3.6.1.4.1.161.19.3.3.1.227 |
fecTxUnderrunNumber of times Tx queue underrun.ro Counter32 .1.3.6.1.4.1.161.19.3.3.1.228 |
fecCarSenseLostCarrier Sense Lost count.ro Counter32 .1.3.6.1.4.1.161.19.3.3.1.229 |
fecNoCarrierNo carrier asserted by external transciever during transmission.ro Counter32 .1.3.6.1.4.1.161.19.3.3.1.230 |
framePeriodCurrentCurrent frame period of the radio.ro Enumeration .1.3.6.1.4.1.161.19.3.3.1.231 |
activeTxPowerStrCurrent transmit power level, including potential power backoff information.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.1.232 |
activeTxPowerHdthsCurrent transmit power level, in hundredths of dBm.ro INTEGER .1.3.6.1.4.1.161.19.3.3.1.233 |
whispBoxConfig OBJECT IDENTIFIER .1.3.6.1.4.1.161.19.3.3.2 |
linkNegoSpeedLink negotiation speeds. H10BT -- 10 Base T Half Duplex, F10BT -- 10 Base T Full Duplex, H100BT -- 100 Base T Half Duplex, F100BT -- 100 Base T Full Duplex. Separate the values with comma when doing a set. e.g. H10BT,F10BT,H100BT,F100BTrwobsolete DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.2.1 |
colorCodeColor code.rw INTEGER .1.3.6.1.4.1.161.19.3.3.2.2 |
displayOnlyAccessThis variable is deprecated.rwobsolete DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.2.3 |
fullAccessFull access password.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.2.4 |
webAutoUpdateWeb page auto update in seconds. 0 means disabled.rw INTEGER UNITS "Seconds" .1.3.6.1.4.1.161.19.3.3.2.5 |
pass1StatusPassword 1(display only) status.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.2.6 |
pass2StatusPassword 2(full access) status.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.2.7 |
bridgeEntryTimeoutBridge table time out Range : 25 -- 1440 Minutes.rw INTEGER .1.3.6.1.4.1.161.19.3.3.2.8 |
snmpMibPermRead/Write permission for MIB groups.rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.9 |
bhTimingModeVariable to switch between Timing Master and Timing Slave. For Backhaul units only.rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.10 |
bhModulationModulation scheme. For Backhaul units only. Only level 4 backhaul can be changed to 20Mbits/Second.rwobsolete Enumeration .1.3.6.1.4.1.161.19.3.3.2.11 |
powerControlPower control. FSK Only.rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.12 |
extFilterDelayObsoleted. External Filters Delay. For 900MHz FSK radios only.rwobsolete INTEGER UNITS "nanoseconds" .1.3.6.1.4.1.161.19.3.3.2.13 |
antennaGainExternal Antenna Gain. For radios that uses an external antenna or the DFS feature.rw INTEGER UNITS "dBi" .1.3.6.1.4.1.161.19.3.3.2.14 |
eirpThis variable is deprecated.rwobsolete INTEGER UNITS "dBm" .1.3.6.1.4.1.161.19.3.3.2.15 |
dynamicLearningTo enable VLAN dynamic learning.rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.16 |
managementVIDManagement VLAN VID.rw INTEGER .1.3.6.1.4.1.161.19.3.3.2.17 |
agingTimeoutAging timeout.rw INTEGER .1.3.6.1.4.1.161.19.3.3.2.18 |
frameTypeAllow only tagged frame.rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.19 |
addVlanMemberWrite-Only OID,Add VLAN number which needs to be added.rw INTEGER .1.3.6.1.4.1.161.19.3.3.2.20 |
removeVlanMemberWrite-only OID,Enter VLAN ID which needs to deleted. If Vlan doesnot exist an error will be returned.rw INTEGER .1.3.6.1.4.1.161.19.3.3.2.21 |
schedulingTo use hardware or software schedulingrw Enumeration .1.3.6.1.4.1.161.19.3.3.2.22 |
transmitterOPTransmitter output power. This is not available on OFDM SMs.rw INTEGER UNITS "dBm" .1.3.6.1.4.1.161.19.3.3.2.23 |
bridgeEnableDisable or enable bridging functionality for a BH unit.rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.24 |
fecEnableDisable or enable FEC error correction functionality for multipoint units.rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.25 |
trapIP1Obsoleted. Configure with whispBoxDNS.trap1.rwobsolete IpAddress .1.3.6.1.4.1.161.19.3.3.2.26 |
trapIP2Obsoleted. Configure with whispBoxDNS.trap2.rwobsolete IpAddress .1.3.6.1.4.1.161.19.3.3.2.27 |
trapIP3Obsoleted. Configure with whispBoxDNS.trap3.rwobsolete IpAddress .1.3.6.1.4.1.161.19.3.3.2.28 |
trapIP4Obsoleted. Configure with whispBoxDNS.trap4.rwobsolete IpAddress .1.3.6.1.4.1.161.19.3.3.2.29 |
trapIP5Obsoleted. Configure with whispBoxDNS.trap5.rwobsolete IpAddress .1.3.6.1.4.1.161.19.3.3.2.30 |
trapIP6Obsoleted. Configure with whispBoxDNS.trap6.rwobsolete IpAddress .1.3.6.1.4.1.161.19.3.3.2.31 |
trapIP7Obsoleted. Configure with whispBoxDNS.trap7.rwobsolete IpAddress .1.3.6.1.4.1.161.19.3.3.2.32 |
trapIP8Obsoleted. Configure with whispBoxDNS.trap8.rwobsolete IpAddress .1.3.6.1.4.1.161.19.3.3.2.33 |
trapIP9Obsoleted. Configure with whispBoxDNS.trap9.rwobsolete IpAddress .1.3.6.1.4.1.161.19.3.3.2.34 |
trapIP10Obsoleted. Configure with whispBoxDNS.trap10.rwobsolete IpAddress .1.3.6.1.4.1.161.19.3.3.2.35 |
commStringRWriteRead/Write Community string. This is a write-only OID.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.2.36 |
subnetMaskSubnet mask for the management IP 1.rw INTEGER .1.3.6.1.4.1.161.19.3.3.2.37 |
mngtIPManagement IP address 1.rw IpAddress .1.3.6.1.4.1.161.19.3.3.2.38 |
allowVIDAccessAllow or disallow local SM management VID access.rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.39 |
setDefaultPlugIf enabled parameters are set to Factory Defaults upon default plug mode detection.rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.40 |
hwsCompatibilityIf enable, it ensures 6.0 compatibility with HWS.rwobsolete Enumeration .1.3.6.1.4.1.161.19.3.3.2.41 |
gpsInputValues 1, 2, 3 have been deprecated. (0) Generate AP sync signal. (1) Deprecated. Sync AP to received signal (Timing Port/UGPS). It will set AutoSync. (2) Deprecated. Sync AP to received signal (Power Port). It will set AutoSync plus Free Run. (3) Deprecated. Sync AP using iGPS (Only on devices which support it). It will set AutoSync plus Free Run. (4) AutoSync. (5) AutoSync plus Free Run.rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.42 |
ismEnable ISM on 5.7GHz frequency band radios.rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.43 |
hiPriorityEnable Hi Priority Data Queue on BH radios.rwobsolete Enumeration .1.3.6.1.4.1.161.19.3.3.2.44 |
userNameUser name.To create read-only user set userMode OID first. Maximum of 4 users can exist in system.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.2.45 |
userPasswordUser password.To create read-only user set userMode OID first.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.2.46 |
userAccessLevelUser access level.To create read-only user set userMode OID first. 1=TECH 2=INSTALL 3=ADMINrw INTEGER .1.3.6.1.4.1.161.19.3.3.2.47 |
deleteUserUser name to remove.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.2.48 |
twoXRateTo enable or disable double rate.rwobsolete Enumeration .1.3.6.1.4.1.161.19.3.3.2.49 |
lanDhcpStateTo enable or disable LAN Interface DHCP feature.rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.50 |
sessionTimeoutTimer for Telnet, Web and FTP sessions.rw INTEGER .1.3.6.1.4.1.161.19.3.3.2.51 |
vlanMemberSourceSpecified the VLAN member source to display. 0=configured, 1=active configuration. Note that this OID is internal to SNMP and is not available at the Web Interface.rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.52 |
addCustomFreqListAdd Custom Frequencies. The frequencies can be in a variety of units up to KHz. Frequencies can be added in a list separated by commas. Example: 3550, 356000, 3450001. A get will return the current custom frequency list. Max string length entered cannot exceed 128 character. Note if there is not enough room for all the frequencies none will be added. Only valid for use on 3.5/3.6 GHz MIMO OFDM Radios, or 450i in 4.9 GHz.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.2.53 |
removeCustomFreqListRemove Custom Frequencies. The frequencies can be in a variety of units up to KHz. Frequencies can be removed in a list separated by commas. Example: 3550, 356000, 3450001. A get will return the current custom frequencies. Only valid for use on 3.5/3.6 GHz MIMO OFDM Radios, or 450i in 4.9 GHz.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.2.54 |
allowColocationAllow or disallow Colocation for software scheduling Backhaul Timing Masters with hardware scheduling Backhaul Timing Masters.rwobsolete Enumeration .1.3.6.1.4.1.161.19.3.3.2.55 |
changeUsrPwdAllow to change the password of a given user of a given user. Usage: userName,password.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.2.56 |
mngtIP2Management IP address 2.rw IpAddress .1.3.6.1.4.1.161.19.3.3.2.57 |
subnetMask2Subnet mask for the management IP 2.rw INTEGER .1.3.6.1.4.1.161.19.3.3.2.58 |
mngtIP3Management IP address 3.rw IpAddress .1.3.6.1.4.1.161.19.3.3.2.59 |
subnetMask3Subnet mask for the management IP 3.rw INTEGER .1.3.6.1.4.1.161.19.3.3.2.60 |
mngtIP4Management IP address 4.rw IpAddress .1.3.6.1.4.1.161.19.3.3.2.61 |
subnetMask4Subnet mask for the management IP 4.rw INTEGER .1.3.6.1.4.1.161.19.3.3.2.62 |
mngtIP5Management IP address 5.rw IpAddress .1.3.6.1.4.1.161.19.3.3.2.63 |
subnetMask5Subnet mask for the management IP 5.rw INTEGER .1.3.6.1.4.1.161.19.3.3.2.64 |
mngtIP6Management IP address 6.rw IpAddress .1.3.6.1.4.1.161.19.3.3.2.65 |
subnetMask6Subnet mask for the management IP 6.rw INTEGER .1.3.6.1.4.1.161.19.3.3.2.66 |
mngtIP7Management IP address 7.rw IpAddress .1.3.6.1.4.1.161.19.3.3.2.67 |
subnetMask7Subnet mask for the management IP 7.rw INTEGER .1.3.6.1.4.1.161.19.3.3.2.68 |
mngtIP8Management IP address 8.rw IpAddress .1.3.6.1.4.1.161.19.3.3.2.69 |
subnetMask8Subnet mask for the management IP 8.rw INTEGER .1.3.6.1.4.1.161.19.3.3.2.70 |
mngtIP9Management IP address 9.rw IpAddress .1.3.6.1.4.1.161.19.3.3.2.71 |
subnetMask9Subnet mask for the management IP 9.rw INTEGER .1.3.6.1.4.1.161.19.3.3.2.72 |
mngtIP10Management IP address 10.rw IpAddress .1.3.6.1.4.1.161.19.3.3.2.73 |
subnetMask10Subnet mask for the management IP 10.rw INTEGER .1.3.6.1.4.1.161.19.3.3.2.74 |
bhvlanEnableTo enable or disable VLAN for Backhaul Master/Slave.rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.75 |
lldpBroadcastEnableTo enable Broadcast of LLDP message, if disabled LLDP uses multicastrw Enumeration .1.3.6.1.4.1.161.19.3.3.2.76 |
regionCodeSet Region Code for the Unit. Used the individual region[Region] OIDs instead.rwdeprecated Enumeration .1.3.6.1.4.1.161.19.3.3.2.77 |
russiaRegionSet Category Region for Russian 5.9/6.05 GHz Radio Only. Use setting under regionAsia now.rwdeprecated Enumeration .1.3.6.1.4.1.161.19.3.3.2.78 |
commStringROnlySet Read Only commnunity string.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.2.79 |
ethernetLinkSpeedSet/Get Ethernet link speed and duplex settings. Note that the Gigabit options are only valid for boards that support Gigabit speeds.rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.80 |
cyclicPrefixCyclic Prefix value, for OFDM Radios only. Deprecated for MIMO SMs. For PMP 430 SMs, this value is only used while in PMP 430 mode (1/16 is forced in PMP 450 mode).rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.81 |
numberCustomFreqNumber of custom frequencies added. There is a maximum of 100. For use on 3.5 GHz OFDM Radios only.ro INTEGER .1.3.6.1.4.1.161.19.3.3.2.82 |
channelBandwidthThe current channel bandwidth in MHz. For use on OFDM Radios only. Obsoleted for MIMO SMs.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.2.83 |
setDefaultsSetting this to 1 will set the radio to Factory Defaults after the next reboot. Setting this to 0 will undo Factory Defaults if and only if Factory Defaults have been set previously without rebooting. Reading this OID will return 0 if Factory Defaults are not set, or a 2 if Factory Defaults are set and we are now awaiting a reboot. NOTE: this operation is reversible as long as you write a 0 to this OID prior to reboot. As a security measure, this OID is only valid when the radio was booted in default plug mode. If the radio is not currently in default plug mode, then attempting to set this OID will fail.rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.84 |
radioRateAdaptRate adaptation parameter 0: 1x No rate adaptation (FSK and SISO OFDM QPSK) 1: 1x/2x (FSK and SISO OFDM 16-QAM) Following are OFDM only: 2: 1x/2x/3x (SISO OFDM 64-QAM) 3: 1x/2x/3x/4x (SISO OFDM 256-QAM) Engineering only Following are MIMO OFDM only: 4: 1x MIMO-A (QPSK duplicated on both paths) 5: 1x/2x MIMO-B (QPSK on each path) 7: 1x/2x/4x MIMO-B (16-QAM on each path) 8: 1x/2x/4x/6x MIMO-B (64-QAM on each path) 9: 1x/2x/4x/6x/8x MIMO-B (256-QAM on each path) 10: 1x/2x MIMO-A (16-QAM duplicated on both paths) 11: 1x/2x/3x MIMO-A (64-QAM duplicated on both paths) 12: 1x/2x/3x/4x MIMO-A (256-QAM duplicated on both paths) For PMP 430 radios this applies to Downlink Rate Adapt only. Use radioRateAdaptUL for setting uplink rate adapt on PMP 430 radios. For PMP 450 radios, write access for engineering use only.rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.85 |
siteInfoViewableEnable non login users the ability to view Site Informationrw Enumeration .1.3.6.1.4.1.161.19.3.3.2.86 |
largeVCQEnable or disable Large VC Qs for SM or PTP radios. Enable when Uplink is being used for camera video feed.rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.87 |
latitudeThe latitude setting of this unit in decimal degrees.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.2.88 |
longitudeThe longitude setting of this unit in decimal degrees.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.2.89 |
heightThe height setting of this unit in meters.rw INTEGER (-2147483647..2147483647) .1.3.6.1.4.1.161.19.3.3.2.90 |
bandwidthRadio bandwidth setting. Deprecated for MIMO SMs. Instead use bandwidthScan.rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.91 |
dataScramblingMethodThis OID is for OFDM only and is obsolete.roobsolete Enumeration .1.3.6.1.4.1.161.19.3.3.2.92 |
portVIDBackhaul Port VID (PVID).rw INTEGER .1.3.6.1.4.1.161.19.3.3.2.93 |
radioRateAdaptULUplink Rate adaptation parameter 0: 1x No rate adaptation (FSK and SISO OFDM QPSK) 1: 1x/2x (FSK and SISO OFDM 16-QAM) Following are OFDM only: 2: 1x/2x/3x (SISO OFDM 64-QAM) 3: 1x/2x/3x/4x (SISO OFDM 256-QAM) Engineering only Following are MIMO OFDM only: 4: 1x MIMO-A (QPSK duplicated on both paths) 5: 1x/2x MIMO-B (QPSK on each path) 7: 1x/2x/4x MIMO-B (16-QAM on each path) 8: 1x/2x/4x/6x MIMO-B (64-QAM on each path) 9: 1x/2x/4x/6x/8x MIMO-B (256-QAM on each path) 10: 1x/2x MIMO-A (16-QAM duplicated on both paths) 11: 1x/2x/3x MIMO-A (64-QAM duplicated on both paths) 12: 1x/2x/3x/4x MIMO-A (256-QAM duplicated on both paths) For PMP 430 radios this applies to Uplink Rate Adapt only. Use radioRateAdapt for setting downlink rate adapt on PMP 430 radios. For PMP 450 radios, engineering use only.rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.94 |
providerVIDProvider VID for QinQ VLAN.rw INTEGER .1.3.6.1.4.1.161.19.3.3.2.95 |
mac1VIDMapAddrMAC Address for Entry 1 in MAC Address VID Mapping Table.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.2.96 |
mac1VIDMapVidVID for Entry 1 in MAC Address VID Mapping Table.rw INTEGER .1.3.6.1.4.1.161.19.3.3.2.97 |
mac2VIDMapAddrMAC Address for Entry 2 in MAC Address VID Mapping Table.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.2.98 |
mac2VIDMapVidVID for Entry 2 in MAC Address VID Mapping Table.rw INTEGER .1.3.6.1.4.1.161.19.3.3.2.99 |
mac3VIDMapAddrMAC Address for Entry 3 in MAC Address VID Mapping Table.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.2.100 |
mac3VIDMapVidVID for Entry 3 in MAC Address VID Mapping Table.rw INTEGER .1.3.6.1.4.1.161.19.3.3.2.101 |
mac4VIDMapAddrMAC Address for Entry 4 in MAC Address VID Mapping Table.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.2.102 |
mac4VIDMapVidVID for Entry 4 in MAC Address VID Mapping Table.rw INTEGER .1.3.6.1.4.1.161.19.3.3.2.103 |
mac5VIDMapAddrMAC Address for Entry 5 in MAC Address VID Mapping Table.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.2.104 |
mac5VIDMapVidVID for Entry 5 in MAC Address VID Mapping Table.rw INTEGER .1.3.6.1.4.1.161.19.3.3.2.105 |
mac6VIDMapAddrMAC Address for Entry 6 in MAC Address VID Mapping Table.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.2.106 |
mac6VIDMapVidVID for Entry 6 in MAC Address VID Mapping Table.rw INTEGER .1.3.6.1.4.1.161.19.3.3.2.107 |
mac7VIDMapAddrMAC Address for Entry 7 in MAC Address VID Mapping Table.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.2.108 |
mac7VIDMapVidVID for Entry 7 in MAC Address VID Mapping Table.rw INTEGER .1.3.6.1.4.1.161.19.3.3.2.109 |
mac8VIDMapAddrMAC Address for Entry 8 in MAC Address VID Mapping Table.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.2.110 |
mac8VIDMapVidVID for Entry 8 in MAC Address VID Mapping Table.rw INTEGER .1.3.6.1.4.1.161.19.3.3.2.111 |
mac9VIDMapAddrMAC Address for Entry 9 in MAC Address VID Mapping Table.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.2.112 |
mac9VIDMapVidVID for Entry 9 in MAC Address VID Mapping Table.rw INTEGER .1.3.6.1.4.1.161.19.3.3.2.113 |
mac10VIDMapAddrMAC Address for Entry 10 in MAC Address VID Mapping Table.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.2.114 |
mac10VIDMapVidVID for Entry 10 in MAC Address VID Mapping Table.rw INTEGER .1.3.6.1.4.1.161.19.3.3.2.115 |
vlanPortTypeVLAN Port Type for VLAN interface. Default is Q.rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.116 |
vlanAcceptQinQFramesAllow/Disallow packets already doubly-tagged (QinQ) to ingress the FEC of BHM, BHS, or MP SM. Not configurable on MP AP.rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.117 |
whispWebUserAccessModeThis variable selects if web page users for the radio should be authenticated locally or via a centralised remote Radius serverrw Enumeration .1.3.6.1.4.1.161.19.3.3.2.118 |
usrAccountEnableAccountingSelect the level of accounting information to be reported to the serverrw Enumeration .1.3.6.1.4.1.161.19.3.3.2.119 |
allowRejectThenLocalControl for allowing local authenication if the AAA remote serverrw Enumeration .1.3.6.1.4.1.161.19.3.3.2.120 |
snrCalculationThis OID is deprecated. Receive quality calulation is always on since it no longer affects packet per second performance.rwdeprecated Enumeration .1.3.6.1.4.1.161.19.3.3.2.121 |
priorityPrecedenceAllows user to decide if 802.1p or DiffServ priority bits should be used first when making priority decisions.rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.122 |
installationColorCodeInstallation Color Code. Allows non-configured SMs to register to an AP with UCC enabled in order to facilitate remote provisioning.rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.123 |
apSmModeSet AP to SM or SM to AP. Useful for facillitating scripting of running Spectrum Analyzer on an AP. Radio must have AP Feature Key. 1 - Set to SM, 0 - Set to AP.rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.124 |
pppoeFilterTo set PPPoE packet filter.rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.125 |
smbFilterTo set SMB packet filter.rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.126 |
snmpFilterTo set SNMP packet filter.rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.127 |
userP1FilterTo set user defined port 1 packet filter.rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.128 |
userP2FilterTo set user defined port 2 packet filter.rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.129 |
userP3FilterTo set user defined port 3 packet filter.rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.130 |
allOtherIpFilterTo set all other IPv4 packet filter.rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.131 |
allIpv4FilterTo set all IPv4 packet filter. Enabling this will automatically enable all of the known IP filters (SMB, SNMP, Bootp, IPv4 Mcast, User Defined Ports, and All Other IPv4).rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.132 |
arpFilterTo set ARP packet filter.rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.133 |
allOthersFilterTo set all other packet filter when.rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.134 |
userDefinedPort1An integer value of number one user defined port. Range:0-65535rw INTEGER .1.3.6.1.4.1.161.19.3.3.2.135 |
port1TCPFilterTo set user defined port 1 TCP traffic filter.rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.136 |
port1UDPFilterTo set user defined port 1 UDP traffic filter.rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.137 |
userDefinedPort2An integer value of number two user defined port. Range:0-65535rw INTEGER .1.3.6.1.4.1.161.19.3.3.2.138 |
port2TCPFilterTo set user defined port 2 TCP traffic filter.rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.139 |
port2UDPFilterTo set user defined port 2 UDP traffic filter.rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.140 |
userDefinedPort3An integer value of number three user defined port. Range:0-65535rw INTEGER .1.3.6.1.4.1.161.19.3.3.2.141 |
port3TCPFilterTo set user defined port 3 TCP traffic filter.rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.142 |
port3UDPFilterTo set user defined port 3 UDP traffic filter.rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.143 |
bootpcFilterTo set bootp client sourced packets filter.rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.144 |
bootpsFilterTo set bootp server sourced packets filter.rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.145 |
ip4MultFilterTo set IPv4 MultiCast packets filter when NAT is disabled.rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.146 |
packetFilterDirectionTo set packet filter direction. Upstream is default.rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.147 |
encryptionConfigFor supported radio, set the encryption algorithm to use. DES by default. Cannot be set if encryption is disabled.rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.148 |
pppoeCtlPriorityPrioritization of PPPoE Control packets.rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.149 |
ftpPortPort used to for FTP. Default is 21.rw INTEGER .1.3.6.1.4.1.161.19.3.3.2.150 |
httpPortPort used to for HTTP. Default is 80.rw INTEGER .1.3.6.1.4.1.161.19.3.3.2.151 |
httpsPortPort used to for HTTPs. Default is 443.rw INTEGER .1.3.6.1.4.1.161.19.3.3.2.152 |
snmpPortPort used to for SNMP. Default is 161.rw INTEGER .1.3.6.1.4.1.161.19.3.3.2.153 |
snmpTrapPortPort used to for SNMP Traps. Default is 162.rw INTEGER .1.3.6.1.4.1.161.19.3.3.2.154 |
webAccessThis variable determines if only HTTP or HTTPs connection are allowed. 0: HTTP Only 1: HTTPs Only 2: HTTP and HTTPs Bothrw Enumeration .1.3.6.1.4.1.161.19.3.3.2.155 |
syslogDomainNameAppendSelect whether to append the configured management domain name to the Syslog server name. For example, if dnsMgmtDomainName is set to 'example.com', syslogServerAddr is set to 'syslog1', and syslogDomainNameAppend is set to appendDomain, the Syslog Server name used would be 'syslog1.example.com'.rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.156 |
syslogServerAddrSyslog server address either in dotted decimal notation or a Fully Qualified Domain Namerw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.2.157 |
syslogServerPortListening port on the Syslog server. Default is 514.rw INTEGER .1.3.6.1.4.1.161.19.3.3.2.158 |
syslogMinLevelSets the minimum syslog severity to transmit. Messages with a lower severity value (i.e. numerically higher) than this will not be transmitted.rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.159 |
allIpv6FilterTo set all IPv6 packet filter. Enabling this will automatically enable all of the known IPv6 filters (SMB, SNMP, Bootp, IPv6 Mcast, User Defined Ports, and All Other IPv6).rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.160 |
ipv6smbFilterTo set IPv6 SMB packet filter.rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.161 |
ipv6snmpFilterTo set IPv6 SNMP packet filter.rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.162 |
ipv6bootpcFilterTo set IPv6 bootp client sourced packets filter.rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.163 |
ipv6bootpsFilterTo set IPv6 bootp server sourced packets filter.rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.164 |
ipv6MultFilterTo set IPv6 MultiCast packets filter when NAT is disabled.rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.165 |
allOtherIpv6FilterTo set all other IPv6 packet filter.rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.166 |
snmpStatusThis variable determines SNMP operation mode. 1: Enable SNMPv2c only 2: Enable SNMPv3 only 3: Enable SNMPv2c and SNMPv3rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.167 |
telnetStatusThis variable determines if Telnet to enabled or not. 0: Disable Telnet 1: Enable Telnetrw Enumeration .1.3.6.1.4.1.161.19.3.3.2.168 |
ftpStatusThis variable determines if FTP to enabled or not. 0: Disable FTP 1: Enable FTPrw Enumeration .1.3.6.1.4.1.161.19.3.3.2.169 |
tftpStatusThis variable determines if TFTP is enabled or not. 0: Disable TFTP 1: Enable TFTPrw Enumeration .1.3.6.1.4.1.161.19.3.3.2.170 |
userModeUser Mode 1=Read-Only 0=Read-Write(default).rw INTEGER .1.3.6.1.4.1.161.19.3.3.2.171 |
tcpAckPriorityPrioritize TCP ACK that are 64 bytes or less.rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.172 |
codePointSelectCodepoint Select.This represents the CodePoint Selection to be modified via Priority Selectrw Enumeration .1.3.6.1.4.1.161.19.3.3.2.173 |
prioritySelectPriority Select.The priority setting input for the CodePoint selected in CodePoint Select.rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.174 |
lan1DhcpReleaseSetting the variable to '1' will release LAN1's IP address and send a DHCP Release Message to the DHCP server. Applicable only when NAT is disabled.rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.201 |
lan1DhcpRenewSetting the variable to '1' will renew LAN1's lease time for its current IP address. Applicable only when NAT is disabled.rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.202 |
lan3DhcpReleaseSetting the variable to '1' will release LAN3's (RF Public) IP address and send a DHCP Release Message to the DHCP server. Applicable only when NAT is enabled.rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.203 |
lan3DhcpRenewSetting the variable to '1' will renew LAN3's (RF Public) lease time for its current IP address. Applicable only when NAT is enabled.rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.204 |
natDhcpReleaseSetting the variable to '1' will release WAN's (NAT Public) IP address and send a DHCP Release Message to the DHCP server. Applicable only when NAT is enabled.rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.205 |
natDhcpRenewSetting the variable to '1' will renew WAN's (NAT Public) lease time for its current IP address. Applicable only when NAT is enabled.rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.206 |
regionSet Region Code for the Unit.ro Enumeration .1.3.6.1.4.1.161.19.3.3.2.207 |
regionAsiaCountry Code for Asia.rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.208 |
regionEuropeCountry Code for Europe.rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.209 |
regionNorthAmericaCountry Code for North America.rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.210 |
regionOceaniaCountry Code for Oceania.rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.211 |
regionSouthAmericaCountry Code for South America.rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.212 |
regionOtherRegulatoryRegulatory setting for governing regulatory body.rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.213 |
interleaveEngineering use only.rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.214 |
receiveQualityDebugEnable or disable receive quality calculations for every packet. Enabling(1) will calulate receive quality on all receiving packets. Due to load on CPU, will slightly packet per second capabilities on AP/BH. Default to disabled for all radios. Only applicable to GenII OFDM products and up.rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.215 |
apTypeIn standard mode, all possible sync sources will be made availble and usedfor autoSync operation. In remote mode, sync over power port will not be available as a sync source. Remote Device mode is where the AP or BHM timing port is connected to an SM or BHS timing port via a sync cable. In this mode, GPS data is unavailable and sync over power port shouldn't be used. If sync over power is desired, and a CMM or other sync over power device is in use, then select standard mode. This should really be named deviceType because this applies to both AP and BHM, but left this as apType for legacy purposes.rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.216 |
regionAfricaCountry Code for Africa.rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.217 |
addCustomFreqMimoFrequency input ie) 3700.50. Deprecated, please use 'addCustomFreqList'.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.2.218 |
removeCustomFreqMimoFrequency input ie) 3700.50. Deprecated, please use 'removeCustomFreqList'.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.2.219 |
timedSpectrumAnalysisDurationBoxValue in seconds for a timed spectrum analysis. Range is 10-1000 seconds.rw INTEGER .1.3.6.1.4.1.161.19.3.3.2.220 |
spectrumAnalysisActionBoxStart or stop timed or continuous Spectrum Analysis and also give status. (0) - Stop Spectrum Analysis (1) - Start Timed Spectrum Analysis Note: AP/BHM will run Spectrum Analysis for the sector. (2) - Start Continuous Spectrum Analysis (3) - Idle, no Spectrum Analysis results. (4) - Idle, Spectrum Analysis results available. (5) - Timed or Remote Spectrum Analysis in progress. (6) - Continuous Spectrum Analysis in progress. Note: Continuous mode has a max of 24 hours. (7) - Spectrum Analyzer not ready.rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.221 |
mac1VIDMapPriorityVID priority for Entry 1 in MAC Address VID Mapping Table.rw INTEGER .1.3.6.1.4.1.161.19.3.3.2.222 |
mac1VIDMapPriorityModeVID priority Mode for Entry 1 in MAC Address VID Mapping Table.rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.223 |
mac2VIDMapPriorityVID priority for Entry 2 in MAC Address VID Mapping Table.rw INTEGER .1.3.6.1.4.1.161.19.3.3.2.224 |
mac2VIDMapPriorityModeVID priority Mode for Entry 2 in MAC Address VID Mapping Table.rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.225 |
mac3VIDMapPriorityVID priority for Entry 3 in MAC Address VID Mapping Table.rw INTEGER .1.3.6.1.4.1.161.19.3.3.2.226 |
mac3VIDMapPriorityModeVID priority Mode for Entry 3 in MAC Address VID Mapping Table.rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.227 |
mac4VIDMapPriorityVID priority for Entry 4 in MAC Address VID Mapping Table.rw INTEGER .1.3.6.1.4.1.161.19.3.3.2.228 |
mac4VIDMapPriorityModeVID priority Mode for Entry 4 in MAC Address VID Mapping Table.rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.229 |
mac5VIDMapPriorityVID priority for Entry 5 in MAC Address VID Mapping Table.rw INTEGER .1.3.6.1.4.1.161.19.3.3.2.230 |
mac5VIDMapPriorityModeVID priority Mode for Entry 5 in MAC Address VID Mapping Table.rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.231 |
mac6VIDMapPriorityVID priority for Entry 6 in MAC Address VID Mapping Table.rw INTEGER .1.3.6.1.4.1.161.19.3.3.2.232 |
mac6VIDMapPriorityModeVID priority Mode for Entry 6 in MAC Address VID Mapping Table.rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.233 |
mac7VIDMapPriorityVID priority for Entry 7 in MAC Address VID Mapping Table.rw INTEGER .1.3.6.1.4.1.161.19.3.3.2.234 |
mac7VIDMapPriorityModeVID priority Mode for Entry 7 in MAC Address VID Mapping Table.rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.235 |
mac8VIDMapPriorityVID priority for Entry 8 in MAC Address VID Mapping Table.rw INTEGER .1.3.6.1.4.1.161.19.3.3.2.236 |
mac8VIDMapPriorityModeVID priority Mode for Entry 8 in MAC Address VID Mapping Table.rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.237 |
mac9VIDMapPriorityVID priority for Entry 9 in MAC Address VID Mapping Table.rw INTEGER .1.3.6.1.4.1.161.19.3.3.2.238 |
mac9VIDMapPriorityModeVID priority Mode for Entry 9 in MAC Address VID Mapping Table.rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.239 |
mac10VIDMapPriorityVID priority for Entry 10 in MAC Address VID Mapping Table.rw INTEGER .1.3.6.1.4.1.161.19.3.3.2.240 |
mac10VIDMapPriorityModeVID priority Mode for Entry 10 in MAC Address VID Mapping Table.rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.241 |
managementVIDPrioritymanagement VID VID VLAN Priority.rw INTEGER .1.3.6.1.4.1.161.19.3.3.2.242 |
managementVIDPriorityModemanagement VID VLAN Priority Mode.rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.243 |
remarkSrcVIDSource VID to apply remarking on.rw INTEGER .1.3.6.1.4.1.161.19.3.3.2.244 |
addRemarkVIDAdd VLAN ID re-marking entry.rw INTEGER .1.3.6.1.4.1.161.19.3.3.2.245 |
addRemarkPriorityAdd 802.1p re-mark entry.rw INTEGER .1.3.6.1.4.1.161.19.3.3.2.246 |
deleteRemarkVIDRemove the VID re-marking for this source VID.rw INTEGER .1.3.6.1.4.1.161.19.3.3.2.247 |
deleteRemarkPriorityRemove the priority re-marking for this source VID.rw INTEGER .1.3.6.1.4.1.161.19.3.3.2.248 |
mimoRateAdaptAlgorithmEngineering use only. Control MIMO Rate Adapt Algorithm 0 = MIMO-A/B This chooses MIMO-A or MIMO-B dynamically to maximize throughput 1 = MIMO-B only 2 = MIMO-A only 3 = SISO onlyrw Enumeration .1.3.6.1.4.1.161.19.3.3.2.249 |
controlMessagesControl Messages (Beacon/Scheduling Map/Acknowledgements/Broadcast) 0 = MIMO-A 1 = SISO MIMO Control Messages is the recommended and default setting. However, SISO Control Messages can be helpful in talking to subscribers on releases previous to 13.2, which operated in this mode.rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.250 |
enableSecurityBannerShows Security Banner at the time of loginrw Enumeration .1.3.6.1.4.1.161.19.3.3.2.251 |
vcDepthVC Depth of radio. Engineering use only.rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.252 |
textSecurityBannerSecurity Banner to be dispalyed on login page. Length should be maximum 1200 characters.Configuration from web UI can enter upto 1499 characters. Only ASCII characters(0-9a-zA-Z,CR,LF) supported.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.2.253 |
acceptSecurityBanner1: User must accept and acknowledge security banner before login. 0: Accepting security banner is not mandatory and user can login without it.rw Enumeration .1.3.6.1.4.1.161.19.3.3.2.254 |
simulatedAirDelaySimulated Air Delay. Engineering use only.rw INTEGER .1.3.6.1.4.1.161.19.3.3.2.256 |
whispBoxControls OBJECT IDENTIFIER .1.3.6.1.4.1.161.19.3.3.3 |
saveFlashThis variable is currently deprecated.rwobsolete Enumeration .1.3.6.1.4.1.161.19.3.3.3.1 |
rebootSetting the variable to 1 will reboot the unit. When the unit finishes rebooting, it will be in finishedReboot state. Setting the variable to 2 will perform a full reboot of a 450i radio, while performing a normal reboot on other radios.rw Enumeration .1.3.6.1.4.1.161.19.3.3.3.2 |
clearEventLogSetting the variable to 1 will clear the event log.rw Enumeration .1.3.6.1.4.1.161.19.3.3.3.3 |
rebootIfRequiredSetting the variable to 1 will reboot the unit if reboot is required.rw Enumeration .1.3.6.1.4.1.161.19.3.3.3.4 |
clearBERStatsSet to clear the BER statistics by sending a 'clearBERStats'. Value is set back to 'doNotClearBERStats' When action is complete.rw Enumeration .1.3.6.1.4.1.161.19.3.3.3.5 |
updateDeviceUse to update the software on the devicerw Enumeration .1.3.6.1.4.1.161.19.3.3.3.6 |
importConfigFileSet to URL to immediately download and apply configuration filerw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.3.7 |
exportConfigFileSet to URL to immediately export and upload configuration filerw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.3.8 |
undoUnitWideSavedChangesSetting to 1 will undo unit wide saved changesrw Enumeration .1.3.6.1.4.1.161.19.3.3.3.9 |
whispBoxBridgeTableBridge table. SEQUENCE OF WhispBoxBridgeEntry .1.3.6.1.4.1.161.19.3.3.4 |
whispBoxBridgeEntryBridge entry. WhispBoxBridgeEntry .1.3.6.1.4.1.161.19.3.3.4.1 |
whispBridgeMacAddrMAC Address of the registered enity.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.4.1.1 |
whispBridgeDesLuidThis is the Local Unit Identifier assigned to Subscriber Modems.ro WhispLUID (WHISP-TCV2-MIB) .1.3.6.1.4.1.161.19.3.3.4.1.2 |
whispBridgeAgeTable entry last access age in minutes.ro INTEGER .1.3.6.1.4.1.161.19.3.3.4.1.3 |
whispBridgeExtTimeout extension flag for entries which also reside in the PNA APR cache.ro INTEGER .1.3.6.1.4.1.161.19.3.3.4.1.4 |
whispBridgeHashHash table array index.ro INTEGER .1.3.6.1.4.1.161.19.3.3.4.1.5 |
whispBridgeCAMThis entry is deprecated.roobsolete INTEGER .1.3.6.1.4.1.161.19.3.3.4.1.6 |
whispBoxEventLog OBJECT IDENTIFIER .1.3.6.1.4.1.161.19.3.3.5 |
whispBoxEvntLogEvent log for AP and SM.ro EventString (WHISP-TCV2-MIB) .1.3.6.1.4.1.161.19.3.3.5.1 |
whispBoxConf OBJECT IDENTIFIER .1.3.6.1.4.1.161.19.3.3.6 |
whispBoxGroups OBJECT IDENTIFIER .1.3.6.1.4.1.161.19.3.3.6.1 |
whispBoxAttributesGroupCanopy Box Level Attributes group. Unknown .1.3.6.1.4.1.161.19.3.3.6.1.1 |
whispBoxControlGroupCanopy Box Level control group. Unknown .1.3.6.1.4.1.161.19.3.3.6.1.2 |
whispBoxBTGroupCanopy Box Bridging Table group. Unknown .1.3.6.1.4.1.161.19.3.3.6.1.3 |
whispBoxVLANTableGroupCanopy Box VLAN member Table group. Unknown .1.3.6.1.4.1.161.19.3.3.6.1.4 |
whispBoxCPTableGroupCode Point Table group. Unknown .1.3.6.1.4.1.161.19.3.3.6.1.5 |
whispBoxUserTableGroupCanopy Box User Information Table group. Unknown .1.3.6.1.4.1.161.19.3.3.6.1.6 |
whispLayer2NeighborTableGroupCanopy Box Layer 2 Neighbor information. Unknown .1.3.6.1.4.1.161.19.3.3.6.1.7 |
whispBoxNotifGroupCanopy Box Notification Group. Unknown .1.3.6.1.4.1.161.19.3.3.6.1.8 |
whispBoxVLANRemarkTableGroupCanopy Box VLAN Remarking Table group. Unknown .1.3.6.1.4.1.161.19.3.3.6.1.9 |
whispBoxSNMPv3GroupCanopy Box SNMPv3 Group. Unknown .1.3.6.1.4.1.161.19.3.3.6.1.10 |
whispBoxLinkTestGroupCanopy Box Link Test group. Unknown .1.3.6.1.4.1.161.19.3.3.6.1.11 |
whispBoxBridgeVar OBJECT IDENTIFIER .1.3.6.1.4.1.161.19.3.3.7 |
whispBridgeTbUsedNumber of used entries in bridging table.ro INTEGER .1.3.6.1.4.1.161.19.3.3.7.1 |
whispBridgeTbFreeNumber of free entries in bridging table.ro INTEGER .1.3.6.1.4.1.161.19.3.3.7.2 |
whispBridgeTbErrBridging table errors.ro INTEGER .1.3.6.1.4.1.161.19.3.3.7.3 |
whispVLANTableVLAN member table. SEQUENCE OF WhispVLANEntry .1.3.6.1.4.1.161.19.3.3.8 |
whispVLANEntryVLAN entry. WhispVLANEntry .1.3.6.1.4.1.161.19.3.3.8.1 |
whispVIDVLAN member ID.ro INTEGER .1.3.6.1.4.1.161.19.3.3.8.1.1 |
whispVTypeVLAN member type.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.8.1.2 |
whispVAgeVLAN member age.ro INTEGER .1.3.6.1.4.1.161.19.3.3.8.1.3 |
whispBoxCPVar OBJECT IDENTIFIER .1.3.6.1.4.1.161.19.3.3.9 |
codePoint0Code Point 0.ro INTEGER .1.3.6.1.4.1.161.19.3.3.9.1 |
codePoint1Code Point 1.rw INTEGER .1.3.6.1.4.1.161.19.3.3.9.2 |
codePoint2Code Point 2.rw INTEGER .1.3.6.1.4.1.161.19.3.3.9.3 |
codePoint3Code Point 3.rw INTEGER .1.3.6.1.4.1.161.19.3.3.9.4 |
codePoint4Code Point 4.rw INTEGER .1.3.6.1.4.1.161.19.3.3.9.5 |
codePoint5Code Point 5.rw INTEGER .1.3.6.1.4.1.161.19.3.3.9.6 |
codePoint6Code Point 6.rw INTEGER .1.3.6.1.4.1.161.19.3.3.9.7 |
codePoint7Code Point 7.rw INTEGER .1.3.6.1.4.1.161.19.3.3.9.8 |
codePoint8Code Point 8.rw INTEGER .1.3.6.1.4.1.161.19.3.3.9.9 |
codePoint9Code Point 9.rw INTEGER .1.3.6.1.4.1.161.19.3.3.9.10 |
codePoint10Code Point 10.rw INTEGER .1.3.6.1.4.1.161.19.3.3.9.11 |
codePoint11Code Point 11.rw INTEGER .1.3.6.1.4.1.161.19.3.3.9.12 |
codePoint12Code Point 12.rw INTEGER .1.3.6.1.4.1.161.19.3.3.9.13 |
codePoint13Code Point 13.rw INTEGER .1.3.6.1.4.1.161.19.3.3.9.14 |
codePoint14Code Point 14.rw INTEGER .1.3.6.1.4.1.161.19.3.3.9.15 |
codePoint15Code Point 15.rw INTEGER .1.3.6.1.4.1.161.19.3.3.9.16 |
codePoint16Code Point 16.rw INTEGER .1.3.6.1.4.1.161.19.3.3.9.17 |
codePoint17Code Point 17.rw INTEGER .1.3.6.1.4.1.161.19.3.3.9.18 |
codePoint18Code Point 18.rw INTEGER .1.3.6.1.4.1.161.19.3.3.9.19 |
codePoint19Code Point 19.rw INTEGER .1.3.6.1.4.1.161.19.3.3.9.20 |
codePoint20Code Point 20.rw INTEGER .1.3.6.1.4.1.161.19.3.3.9.21 |
codePoint21Code Point 21.rw INTEGER .1.3.6.1.4.1.161.19.3.3.9.22 |
codePoint22Code Point 22.rw INTEGER .1.3.6.1.4.1.161.19.3.3.9.23 |
codePoint23Code Point 23.rw INTEGER .1.3.6.1.4.1.161.19.3.3.9.24 |
codePoint24Code Point 24.rw INTEGER .1.3.6.1.4.1.161.19.3.3.9.25 |
codePoint25Code Point 25.rw INTEGER .1.3.6.1.4.1.161.19.3.3.9.26 |
codePoint26Code Point 26.rw INTEGER .1.3.6.1.4.1.161.19.3.3.9.27 |
codePoint27Code Point 27.rw INTEGER .1.3.6.1.4.1.161.19.3.3.9.28 |
codePoint28Code Point 28.rw INTEGER .1.3.6.1.4.1.161.19.3.3.9.29 |
codePoint29Code Point 29.rw INTEGER .1.3.6.1.4.1.161.19.3.3.9.30 |
codePoint30Code Point 30.rw INTEGER .1.3.6.1.4.1.161.19.3.3.9.31 |
codePoint31Code Point 31.rw INTEGER .1.3.6.1.4.1.161.19.3.3.9.32 |
codePoint32Code Point 32.rw INTEGER .1.3.6.1.4.1.161.19.3.3.9.33 |
codePoint33Code Point 33.rw INTEGER .1.3.6.1.4.1.161.19.3.3.9.34 |
codePoint34Code Point 34.rw INTEGER .1.3.6.1.4.1.161.19.3.3.9.35 |
codePoint35Code Point 35.rw INTEGER .1.3.6.1.4.1.161.19.3.3.9.36 |
codePoint36Code Point 36.rw INTEGER .1.3.6.1.4.1.161.19.3.3.9.37 |
codePoint37Code Point 37.rw INTEGER .1.3.6.1.4.1.161.19.3.3.9.38 |
codePoint38Code Point 38.rw INTEGER .1.3.6.1.4.1.161.19.3.3.9.39 |
codePoint39Code Point 39.rw INTEGER .1.3.6.1.4.1.161.19.3.3.9.40 |
codePoint40Code Point 40.rw INTEGER .1.3.6.1.4.1.161.19.3.3.9.41 |
codePoint41Code Point 41.rw INTEGER .1.3.6.1.4.1.161.19.3.3.9.42 |
codePoint42Code Point 42.rw INTEGER .1.3.6.1.4.1.161.19.3.3.9.43 |
codePoint43Code Point 43.rw INTEGER .1.3.6.1.4.1.161.19.3.3.9.44 |
codePoint44Code Point 44.rw INTEGER .1.3.6.1.4.1.161.19.3.3.9.45 |
codePoint45Code Point 45.rw INTEGER .1.3.6.1.4.1.161.19.3.3.9.46 |
codePoint46Code Point 46.rw INTEGER .1.3.6.1.4.1.161.19.3.3.9.47 |
codePoint47Code Point 47.rw INTEGER .1.3.6.1.4.1.161.19.3.3.9.48 |
codePoint48Code Point 48.ro INTEGER .1.3.6.1.4.1.161.19.3.3.9.49 |
codePoint49Code Point 49.rw INTEGER .1.3.6.1.4.1.161.19.3.3.9.50 |
codePoint50Code Point 50.rw INTEGER .1.3.6.1.4.1.161.19.3.3.9.51 |
codePoint51Code Point 51.rw INTEGER .1.3.6.1.4.1.161.19.3.3.9.52 |
codePoint52Code Point 52.rw INTEGER .1.3.6.1.4.1.161.19.3.3.9.53 |
codePoint53Code Point 53.rw INTEGER .1.3.6.1.4.1.161.19.3.3.9.54 |
codePoint54Code Point 54.rw INTEGER .1.3.6.1.4.1.161.19.3.3.9.55 |
codePoint55Code Point 55.rw INTEGER .1.3.6.1.4.1.161.19.3.3.9.56 |
codePoint56Code Point 56.ro INTEGER .1.3.6.1.4.1.161.19.3.3.9.57 |
codePoint57Code Point 57.rw INTEGER .1.3.6.1.4.1.161.19.3.3.9.58 |
codePoint58Code Point 58.rw INTEGER .1.3.6.1.4.1.161.19.3.3.9.59 |
codePoint59Code Point 59.rw INTEGER .1.3.6.1.4.1.161.19.3.3.9.60 |
codePoint60Code Point 60.rw INTEGER .1.3.6.1.4.1.161.19.3.3.9.61 |
codePoint61Code Point 61.rw INTEGER .1.3.6.1.4.1.161.19.3.3.9.62 |
codePoint62Code Point 62.rw INTEGER .1.3.6.1.4.1.161.19.3.3.9.63 |
codePoint63Code Point 63.rw INTEGER .1.3.6.1.4.1.161.19.3.3.9.64 |
whispUserTableUser information table. SEQUENCE OF WhispUserEntry .1.3.6.1.4.1.161.19.3.3.10 |
whispUserEntryUser entry. WhispUserEntry .1.3.6.1.4.1.161.19.3.3.10.1 |
entryIndexUser information table index.ro INTEGER .1.3.6.1.4.1.161.19.3.3.10.1.1 |
userLoginNameUser name.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.10.1.2 |
userPswdUser password.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.10.1.3 |
accessLevelUser access level.ro INTEGER .1.3.6.1.4.1.161.19.3.3.10.1.4 |
loginStatusUser current status.ro INTEGER .1.3.6.1.4.1.161.19.3.3.10.1.5 |
loginMethodUser login method.ro INTEGER .1.3.6.1.4.1.161.19.3.3.10.1.6 |
sessionTimeUsers logged in session time.ro INTEGER .1.3.6.1.4.1.161.19.3.3.10.1.7 |
whispLayer2NeighborTableNeighbor information table. SEQUENCE OF WhispLayer2NeighborEntry .1.3.6.1.4.1.161.19.3.3.11 |
whispLayer2NeighborEntryNeighbor Entry. WhispLayer2NeighborEntry .1.3.6.1.4.1.161.19.3.3.11.1 |
entryL2IndexNeighbor information table index.ro INTEGER .1.3.6.1.4.1.161.19.3.3.11.1.1 |
neighborMACNeighbor MAC.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.11.1.2 |
neighborIPNeighbor IP.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.11.1.3 |
neighborSiteNameNeighbor Site Name.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.11.1.4 |
whispBoxEvent OBJECT IDENTIFIER .1.3.6.1.4.1.161.19.3.3.12 |
whispBoxDHCPClientEvent OBJECT IDENTIFIER .1.3.6.1.4.1.161.19.3.3.12.1 |
boxLan1DHCPClientEventLan1 DHCP Client has received a new address via DHCP NOTIFICATION-TYPE .1.3.6.1.4.1.161.19.3.3.12.1.1 |
whispBoxDNS OBJECT IDENTIFIER .1.3.6.1.4.1.161.19.3.3.13 |
dnsIpStateConfiguration for DNS server IP addresses of the management interface are learned: 0 : Manual, must configure dnsPrimaryMgmtIP and dnsAlternateMgmtIP 1 : Automatic, DNS servers IP addresses are learned from DHCP response of the interfacerw Enumeration .1.3.6.1.4.1.161.19.3.3.13.1 |
dnsPrimaryMgmtIPPrimary DNS IP address for the management interface.rw IpAddress .1.3.6.1.4.1.161.19.3.3.13.2 |
dnsAlternateMgmtIPSecondary DNS IP address for the management interface.rw IpAddress .1.3.6.1.4.1.161.19.3.3.13.3 |
dnsMgmtDomainNameDomain Name to use for management DNS configuration. This domain name may be concatonated to DNS names used configured for the management interface.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.13.4 |
trapDomainNameAppendSelect whether to append the configured management domain name to the configured trap names. For example, if dnsMgmtDomainName is set to 'example.com', trap1 is set to 'trap1', and trapDomainNameAppend is set to appendDomain, the trap1 name used would be 'trap1.example.com'.rw Enumeration .1.3.6.1.4.1.161.19.3.3.13.5 |
trap1SNMP Trap IP Address 1. Format is either an IP address or DNS name.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.13.6 |
trap2SNMP Trap IP Address 2. Format is either an IP address or DNS name.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.13.7 |
trap3SNMP Trap IP Address 3. Format is either an IP address or DNS name.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.13.8 |
trap4SNMP Trap IP Address 4. Format is either an IP address or DNS name.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.13.9 |
trap5SNMP Trap IP Address 5. Format is either an IP address or DNS name.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.13.10 |
trap6SNMP Trap IP Address 6. Format is either an IP address or DNS name.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.13.11 |
trap7SNMP Trap IP Address 7. Format is either an IP address or DNS name.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.13.12 |
trap8SNMP Trap IP Address 8. Format is either an IP address or DNS name.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.13.13 |
trap9SNMP Trap IP Address 9. Format is either an IP address or DNS name.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.13.14 |
trap10SNMP Trap IP Address 10. Format is either an IP address or DNS name.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.13.15 |
whispBoxSNMPv3 OBJECT IDENTIFIER .1.3.6.1.4.1.161.19.3.3.14 |
snmpv2cEnableEnable(1) or Disable(0) SNMPv2c accessrw Enumeration .1.3.6.1.4.1.161.19.3.3.14.1 |
snmpv3EngineIdThe SNMPv3 engine administratively-unique identifier. Length of the identifier should be 5-32 octets which is 10-64 hexadecimal characters and even.rw OCTET STRING .1.3.6.1.4.1.161.19.3.3.14.2 |
snmpv3SecLvlThe security level of the SNMPv3 Engine.rw Enumeration .1.3.6.1.4.1.161.19.3.3.14.3 |
snmpv3AuthProtThe SNMPv3 message authentication protocol to use. Currently only MD5 is supported.rw Enumeration .1.3.6.1.4.1.161.19.3.3.14.4 |
snmpv3PrivProtThe SNMPv3 message privacy/encryption protocol to use. Currently only CBC-DES is supported.rw Enumeration .1.3.6.1.4.1.161.19.3.3.14.5 |
roUserNameSNMPv3 Read-Only username.rw OCTET STRING .1.3.6.1.4.1.161.19.3.3.14.6 |
roAuthPasswordSNMPv3 Read-Only message authentication password.Minimum 8 and maximum 32 characters long.rw OCTET STRING .1.3.6.1.4.1.161.19.3.3.14.7 |
roPrivPasswordSNMPv3 Read-Only message privacy/encryption password.Minimum 8 and maximum 32 characters long.rw OCTET STRING .1.3.6.1.4.1.161.19.3.3.14.8 |
rwUserEnableSNMPv3 Read-Write User Enable.rw Enumeration .1.3.6.1.4.1.161.19.3.3.14.9 |
rwUserNameSNMPv3 Read-Write Username.rw OCTET STRING .1.3.6.1.4.1.161.19.3.3.14.10 |
rwAuthPasswordSNMPv3 Read-Write message authentication password.Minimum 8 and maximum 32 characters long.rw OCTET STRING .1.3.6.1.4.1.161.19.3.3.14.11 |
rwPrivPasswordSNMPv3 Read-Write message privacy/encryption password.Minimum 8 and maximum 32 characters long.rw OCTET STRING .1.3.6.1.4.1.161.19.3.3.14.12 |
snmpv3TrapEnableSNMPv3 Trap enable option: (0) Disable - No SNMPv3 Traps Sent (1) Enable Traps to be sent for SNMPv3 Read-Only User (2) Enable Traps to be sent for SNMPv3 Read-Write User NOTE: When disabled SNMPv2c Trap configuration is used.rw Enumeration .1.3.6.1.4.1.161.19.3.3.14.13 |
whispBoxRFPhysical OBJECT IDENTIFIER .1.3.6.1.4.1.161.19.3.3.15 |
whispBoxRFPhysicalRadiosRadio information table. SEQUENCE OF WhispBoxRFPhysicalRadioEntry .1.3.6.1.4.1.161.19.3.3.15.1 |
whispBoxRFPhysicalRadioEntryRadio information table entry. WhispBoxRFPhysicalRadioEntry .1.3.6.1.4.1.161.19.3.3.15.1.1 |
radioIndexRadio Index.ro INTEGER .1.3.6.1.4.1.161.19.3.3.15.1.1.1 |
radioTypeIndicates if the radio is FSK or OFDM.ro Enumeration .1.3.6.1.4.1.161.19.3.3.15.1.1.2 |
radioPathsIndicates number of paths. For FSK or OFDM (non-MIMO), this is 1. For MIMO, it can be greater (with a current maximum of 2).ro INTEGER .1.3.6.1.4.1.161.19.3.3.15.1.1.3 |
whispBoxRFPhysicalRadioPathsRadio path information table. SEQUENCE OF WhispBoxRFPhysicalRadioPathEntry .1.3.6.1.4.1.161.19.3.3.15.2 |
whispBoxRFPhysicalRadioPathEntryRadio path table entry. WhispBoxRFPhysicalRadioPathEntry .1.3.6.1.4.1.161.19.3.3.15.2.1 |
pathIndexPath Index.ro INTEGER .1.3.6.1.4.1.161.19.3.3.15.2.1.1 |
whispBoxRFPhysicalRadioFrequenciesAvailable frequency information table. SEQUENCE OF WhispBoxRFPhysicalRadioFrequencyEntry .1.3.6.1.4.1.161.19.3.3.15.3 |
whispBoxRFPhysicalRadioFrequencyEntryAvailable frequency table entry. WhispBoxRFPhysicalRadioFrequencyEntry .1.3.6.1.4.1.161.19.3.3.15.3.1 |
frequencyFrequency.ro INTEGER .1.3.6.1.4.1.161.19.3.3.15.3.1.1 |
whispBoxRFConfig OBJECT IDENTIFIER .1.3.6.1.4.1.161.19.3.3.16 |
whispBoxRFConfigRadiosRadio configuration table. SEQUENCE OF WhispBoxRFConfigRadioEntry .1.3.6.1.4.1.161.19.3.3.16.1 |
whispBoxRFConfigRadioEntryRadio config table entry. WhispBoxRFConfigRadioEntry .1.3.6.1.4.1.161.19.3.3.16.1.1 |
radioConfigIndexRadio Config Index.ro INTEGER .1.3.6.1.4.1.161.19.3.3.16.1.1.1 |
radioFrequencyBandCurrently configured radio band.ro Enumeration .1.3.6.1.4.1.161.19.3.3.16.1.1.2 |
whispVLANRemarkTableActive VLAN Remarking table. SEQUENCE OF WhispVLANRemarkEntry .1.3.6.1.4.1.161.19.3.3.17 |
whispVLANRemarkEntryRemarking VLAN entry. WhispVLANRemarkEntry .1.3.6.1.4.1.161.19.3.3.17.1 |
sourceVIDSource VLAN ID.ro INTEGER .1.3.6.1.4.1.161.19.3.3.17.1.1 |
remarkVIDStateRemark VID State.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.17.1.2 |
remarkVIDRemark VID.ro INTEGER .1.3.6.1.4.1.161.19.3.3.17.1.3 |
remarkPriorityStateRemark Priority State.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.17.1.4 |
remarkPriorityRemark Priority.ro INTEGER .1.3.6.1.4.1.161.19.3.3.17.1.5 |
whispBoxLink OBJECT IDENTIFIER .1.3.6.1.4.1.161.19.3.3.18 |
whispBoxLinkTestConfig OBJECT IDENTIFIER .1.3.6.1.4.1.161.19.3.3.18.1 |
linkTestLUIDBoxLUID selection for Link Test. Valid range: 2-255. Read-Only for SM or Backhaul slave, Read/Write for AP.rw INTEGER .1.3.6.1.4.1.161.19.3.3.18.1.1 |
linkTestDurationBoxDuration for the Link Test. Valid range: 2-10 secondsrw INTEGER .1.3.6.1.4.1.161.19.3.3.18.1.2 |
linkTestActionBoxSetting value 1 will initiate link test. Note that trying to set 0 will not stop the test. In fact it will return an error message. The value of 0 just indicates the idle state meaning no test is running or the current test is done. That's why the word stopped is used and not the action verb stop.rw Enumeration .1.3.6.1.4.1.161.19.3.3.18.1.3 |
linkTestPktLengthBoxPacket length for Link Test. Valid range: 64-1714 bytesrw INTEGER .1.3.6.1.4.1.161.19.3.3.18.1.4 |
linkTestModeBoxLink Test Mode 0 = RF Link Test (traffic doesn't go through bridge, highest throughput) 1 = Link Test with Bridging 2 = Link Test with Bridging and MIR 3 = Extrapolated Link Test (send only a few packets measuring their quality and extrapolate out the throughput) This is an estimation of the throughput based upon the modulation, efficiency, and data slots available. It intended to provide a basic link test test without impacting service for the sector. Extrapolated Link Test is not available for FSK radios.rw Enumeration .1.3.6.1.4.1.161.19.3.3.18.1.5 |
linkTestSNRCalculationBoxEnable or disable Signal to Noise Ratio (SNR) calculations during a Link Test. Enabling(1) will calulate SNR on all receiving packets. Due to load on CPU, will slightly degrade packet per second capabilities. Only applicable to GenII OFDM products and up.rw Enumeration .1.3.6.1.4.1.161.19.3.3.18.1.6 |
linkTestWithDualPathBoxLink Test with: 0 = Low Priority VC only 1 = High and Low Priority VCsrw Enumeration .1.3.6.1.4.1.161.19.3.3.18.1.7 |
linkTestNumPktBoxNumber of packets to send. Valid range: 0-64 where 0 will flood the link for the duration of the test.rw INTEGER .1.3.6.1.4.1.161.19.3.3.18.1.8 |
linkTestForceModulationBoxEngineering use only. Link Test with: 0 = Normal Rate Adapt algorithm 1 = Force to max modultion - No Rate Adapt Algorithmrw Enumeration .1.3.6.1.4.1.161.19.3.3.18.1.9 |
linkTestDirectionBoxLink Test Direction - Engineering Use Only 0 = default (will do bidirectional) 1 = Uplink Only 2 = Downlink Only 3 = Bi-Directional (same as 0, setting to 3 will result in setting it to 0)rw Enumeration .1.3.6.1.4.1.161.19.3.3.18.1.10 |
whispBoxLinkTestResult OBJECT IDENTIFIER .1.3.6.1.4.1.161.19.3.3.18.2 |
testLUIDBoxLUID number of selected unit.ro INTEGER .1.3.6.1.4.1.161.19.3.3.18.2.1 |
linkTestStatusBoxStatus for Link Test.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.18.2.2 |
linkTestErrorBoxError status of Link Test: (1) Failed to recieve handshake from remote device (2) No session is currently active. Please try again after session established. (3) Received a bad transaction ID. Please try again. (4) We werent able to send the test request to the remote device. (5) We didnt receive any results from the remote device.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.18.2.3 |
testDurationBoxDuration of link test.ro INTEGER .1.3.6.1.4.1.161.19.3.3.18.2.4 |
downLinkRateBoxDownlink Rate.ro INTEGER UNITS "bps" .1.3.6.1.4.1.161.19.3.3.18.2.5 |
upLinkRateBoxUplink Rate.ro INTEGER UNITS "bps" .1.3.6.1.4.1.161.19.3.3.18.2.6 |
downLinkEffBoxDown Link Efficiency.ro INTEGER UNITS "%" .1.3.6.1.4.1.161.19.3.3.18.2.7 |
maxDwnLinkIndexBoxFor link test results, the maximum possible downlink efficiency percentage (always 100%).ro INTEGER .1.3.6.1.4.1.161.19.3.3.18.2.8 |
actDwnLinkIndexBoxActual down link index.ro INTEGER .1.3.6.1.4.1.161.19.3.3.18.2.9 |
expDwnFragCountBoxExpected Fragment Count.ro Gauge32 .1.3.6.1.4.1.161.19.3.3.18.2.10 |
actDwnFragCountBoxActual Fragment Countro Gauge32 .1.3.6.1.4.1.161.19.3.3.18.2.11 |
upLinkEffBoxUp link efficiency.ro INTEGER UNITS "%" .1.3.6.1.4.1.161.19.3.3.18.2.12 |
expUpFragCountBoxUplink expected Fragment Count.ro Gauge32 .1.3.6.1.4.1.161.19.3.3.18.2.13 |
actUpFragCountBoxActual uplink Fragment Count.ro Gauge32 .1.3.6.1.4.1.161.19.3.3.18.2.14 |
maxUpLinkIndexBoxFor link test results, the maximum possible uplink efficiency percentage (always 100%).ro INTEGER .1.3.6.1.4.1.161.19.3.3.18.2.15 |
actUpLinkIndexBoxActual Up link index.ro INTEGER .1.3.6.1.4.1.161.19.3.3.18.2.16 |
fragments1xDwnLinkVerticalBoxNumber of fragments received on down link at 1X (QPSK). For Gen II OFDM and forward. For MIMO this is the vertical path.ro INTEGER .1.3.6.1.4.1.161.19.3.3.18.2.17 |
fragments2xDwnLinkVerticalBoxNumber of fragments received on down link at 2X (16-QAM). For Gen II OFDM and forward. For MIMO this is the vertical path.ro INTEGER .1.3.6.1.4.1.161.19.3.3.18.2.18 |
fragments3xDwnLinkVerticalBoxNumber of fragments received on down link at 3X (64-QAM). For Gen II OFDM and forward. For MIMO this is the vertical path.ro INTEGER .1.3.6.1.4.1.161.19.3.3.18.2.19 |
fragments4xDwnLinkVerticalBoxNumber of fragments received on down link at 4X (256-QAM). For Gen II OFDM and forward. For MIMO this is the vertical path.ro INTEGER .1.3.6.1.4.1.161.19.3.3.18.2.20 |
fragments1xUpLinkVerticalBoxNumber of fragments received on up link at 1X (QPSK). For Gen II OFDM and forward. For MIMO this is the vertical path.ro INTEGER .1.3.6.1.4.1.161.19.3.3.18.2.21 |
fragments2xUpLinkVerticalBoxNumber of fragments received on up link at 2X (16-QAM). For Gen II OFDM and forward. For MIMO this is the vertical path.ro INTEGER .1.3.6.1.4.1.161.19.3.3.18.2.22 |
fragments3xUpLinkVerticalBoxNumber of fragments received on up link at 3X (64-QAM). For Gen II OFDM and forward. For MIMO this is the vertical path.ro INTEGER .1.3.6.1.4.1.161.19.3.3.18.2.23 |
fragments4xUpLinkVerticalBoxNumber of fragments received on up link at 4X (256-QAM). For Gen II OFDM and forward. For MIMO this is the vertical path.ro INTEGER .1.3.6.1.4.1.161.19.3.3.18.2.24 |
bitErrorsCorrected1xDwnLinkVerticalBoxNumber of bit errors corrected on average per fragment on down link at 1X (QPSK). For Gen II OFDM and forward. For MIMO this is the vertical path.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.18.2.25 |
bitErrorsCorrected2xDwnLinkVerticalBoxNumber of bit errors corrected on average per fragment on down link at 2X (16-QAM). For Gen II OFDM and forward. For MIMO this is the vertical path.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.18.2.26 |
bitErrorsCorrected3xDwnLinkVerticalBoxNumber of bit errors corrected on average per fragment on down link at 3X (64-QAM). For Gen II OFDM and forward. For MIMO this is the vertical path.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.18.2.27 |
bitErrorsCorrected4xDwnLinkVerticalBoxNumber of bit errors corrected on average per fragment on down link at 4X (256-QAM). For Gen II OFDM and forward. For MIMO this is the vertical path.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.18.2.28 |
bitErrorsCorrected1xUpLinkVerticalBoxNumber of bit errors corrected on average per fragment on up link at 1X (QPSK). For Gen II OFDM and forward. For MIMO this is the vertical path.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.18.2.29 |
bitErrorsCorrected2xUpLinkVerticalBoxNumber of bit errors corrected on average per fragment on up link at 2X (16-QAM). For Gen II OFDM and forward. For MIMO this is the vertical path.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.18.2.30 |
bitErrorsCorrected3xUpLinkVerticalBoxNumber of bit errors corrected on average per fragment on up link at 3X (64-QAM). For Gen II OFDM and forward. For MIMO this is the vertical path.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.18.2.31 |
bitErrorsCorrected4xUpLinkVerticalBoxNumber of bit errors corrected on average per fragment on up link at 4X (256-QAM). For Gen II OFDM and forward. For MIMO this is the vertical path.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.18.2.32 |
signalToNoiseRatioDownLinkVerticalBoxEstimated Signal to Noise Ratio in dB for the down link. For Gen II OFDM and forward. For MIMO this is the vertical path.ro INTEGER .1.3.6.1.4.1.161.19.3.3.18.2.33 |
signalToNoiseRatioUpLinkVerticalBoxEstimated Signal to Noise Ratio in dB for the up link. For Gen II OFDM and forward. For MIMO this is the vertical path.ro INTEGER .1.3.6.1.4.1.161.19.3.3.18.2.34 |
fragments1xDwnLinkHorizontalBoxNumber of fragments received on down link at 1X (QPSK). For MIMO only. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical.ro INTEGER .1.3.6.1.4.1.161.19.3.3.18.2.35 |
fragments2xDwnLinkHorizontalBoxNumber of fragments received on down link at 2X (16-QAM). For MIMO only. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical.ro INTEGER .1.3.6.1.4.1.161.19.3.3.18.2.36 |
fragments3xDwnLinkHorizontalBoxNumber of fragments received on down link at 3X (64-QAM). For MIMO only. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical.ro INTEGER .1.3.6.1.4.1.161.19.3.3.18.2.37 |
fragments4xDwnLinkHorizontalBoxNumber of fragments received on down link at 4X (256-QAM). For MIMO only. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical.ro INTEGER .1.3.6.1.4.1.161.19.3.3.18.2.38 |
fragments1xUpLinkHorizontalBoxNumber of fragments received on up link at 1X (QPSK). For MIMO only. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical.ro INTEGER .1.3.6.1.4.1.161.19.3.3.18.2.39 |
fragments2xUpLinkHorizontalBoxNumber of fragments received on up link at 2X (16-QAM). For MIMO only. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical.ro INTEGER .1.3.6.1.4.1.161.19.3.3.18.2.40 |
fragments3xUpLinkHorizontalBoxNumber of fragments received on up link at 3X (64-QAM). For MIMO only. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical.ro INTEGER .1.3.6.1.4.1.161.19.3.3.18.2.41 |
fragments4xUpLinkHorizontalBoxNumber of fragments received on up link at 4X (256-QAM). For MIMO only. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical.ro INTEGER .1.3.6.1.4.1.161.19.3.3.18.2.42 |
bitErrorsCorrected1xDwnLinkHorizontalBoxNumber of bit errors corrected on average per fragment on down link at 1X (QPSK). For MIMO and forward. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.18.2.43 |
bitErrorsCorrected2xDwnLinkHorizontalBoxNumber of bit errors corrected on average per fragment on down link at 2X (16-QAM). For MIMO and forward. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.18.2.44 |
bitErrorsCorrected3xDwnLinkHorizontalBoxNumber of bit errors corrected on average per fragment on down link at 3X (64-QAM). For MIMO and forward. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.18.2.45 |
bitErrorsCorrected4xDwnLinkHorizontalBoxNumber of bit errors corrected on average per fragment on down link at 4X (256-QAM). For MIMO and forward. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.18.2.46 |
bitErrorsCorrected1xUpLinkHorizontalBoxNumber of bit errors corrected on average per fragment on up link at 1X (QPSK). For MIMO and forward. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.18.2.47 |
bitErrorsCorrected2xUpLinkHorizontalBoxNumber of bit errors corrected on average per fragment on up link at 2X (16-QAM). For MIMO and forward. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.18.2.48 |
bitErrorsCorrected3xUpLinkHorizontalBoxEngineering use only. Number of bit errors corrected on average per fragment on up link at 3X (64-QAM). For MIMO and forward. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.18.2.49 |
bitErrorsCorrected4xUpLinkHorizontalBoxNumber of bit errors corrected on average per fragment on up link at 4X (256-QAM). For MIMO and forward. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.18.2.50 |
signalToNoiseRatioDownLinkHorizontalBoxEstimated Signal to Noise Ratio in dB for the down link. For MIMO and forward. For MIMO this is the horizontal path. If operating in MIMO-A this will return 0.ro INTEGER .1.3.6.1.4.1.161.19.3.3.18.2.51 |
signalToNoiseRatioUpLinkHorizontalBoxEstimated Signal to Noise Ratio in dB for the up link. For Gen II OFDM and forward. For MIMO this is the horizontal path. If operating in MIMO-A this will return 0.ro INTEGER .1.3.6.1.4.1.161.19.3.3.18.2.52 |
downLinkRateExtrapolatedBoxExtrapolated Downlink Rate from an extrapolated link test. Extrapolated Link Test sends only a few packets over the link and extrapolates this out to what would happen on a full link test. This is an estimation of the throughput based upon the modulation, efficiency, and data slots available. It intended to provide a basic link test test without impacting service for the sector.ro INTEGER UNITS "bps" .1.3.6.1.4.1.161.19.3.3.18.2.53 |
upLinkRateExtrapolatedBoxExtrapolated Uplink Rate from an extrapolated link test. Extrapolated Link Test sends only a few packets over the link and extrapolates this out to what would happen on a full link test. This is an estimation of the throughput based upon the modulation, efficiency, and data slots available. It intended to provide a basic link test test without impacting service for the sector.ro INTEGER UNITS "bps" .1.3.6.1.4.1.161.19.3.3.18.2.54 |
linkTestLastRunTimeTime and Date when last link test ran.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.18.2.55 |
whispRegStatusBoxThis shows the registration status of a link.roobsolete DisplayString (SNMPv2-TC) .1.3.6.1.4.1.161.19.3.3.18.4 |