SN-MSPS-SCX200-MIB
Detailed view of the defined objects, syntax rules, and hierarchical paths.
582
Objects
Active
Status
16
Dependencies
Imported Objects
Objects
582 total| Object Name |
|---|
org OBJECT IDENTIFIER .1.3 |
dod OBJECT IDENTIFIER .1.3.6 |
internet OBJECT IDENTIFIER .1.3.6.1 |
private OBJECT IDENTIFIER .1.3.6.1.4 |
enterprises OBJECT IDENTIFIER .1.3.6.1.4.1 |
siemens OBJECT IDENTIFIER .1.3.6.1.4.1.4329 |
industrialComProducts OBJECT IDENTIFIER .1.3.6.1.4.1.4329.20 |
iComPlatforms OBJECT IDENTIFIER .1.3.6.1.4.1.4329.20.1 |
simaticNet OBJECT IDENTIFIER .1.3.6.1.4.1.4329.20.1.1 |
snMsps OBJECT IDENTIFIER .1.3.6.1.4.1.4329.20.1.1.1 |
snMspsTrapPrefix OBJECT IDENTIFIER .1.3.6.1.4.1.4329.20.1.1.1.0 |
snMspsTrapMSTPNewRootbridgeDetected(M)STP new Rootbridge detected. Variable Bindings: Bridge Address, Old Root Bridge, New Root Bridge TRAP-TYPE .1.3.6.1.4.1.4329.20.1.1.1.0.251 |
snMspsTrapMSTPTopChange(M)STP Topologychange detected. TRAP-TYPE .1.3.6.1.4.1.4329.20.1.1.1.0.252 |
snMspsTrapPnacPortAuthStateChangePnac port auth state change notification. TRAP-TYPE .1.3.6.1.4.1.4329.20.1.1.1.0.451 |
snMspsTrapRmActiveStateRedundancy manager entered active state. TRAP-TYPE .1.3.6.1.4.1.4329.20.1.1.1.0.1451 |
snMspsTrapRmPassiveStateRedundancy manager entered passive state. TRAP-TYPE .1.3.6.1.4.1.4329.20.1.1.1.0.1452 |
snMspsTrapStandbyActiveStateStandby manager entered active state. TRAP-TYPE .1.3.6.1.4.1.4329.20.1.1.1.0.1501 |
snMspsTrapStandbyPassiveStateStandby manager entered passive state. TRAP-TYPE .1.3.6.1.4.1.4329.20.1.1.1.0.1502 |
snMspsTrapWlanGenericA generic WLAN event occured. TRAP-TYPE .1.3.6.1.4.1.4329.20.1.1.1.0.1751 |
snMspsTrapWlanNewOverlapApNew Overlap-AP found TRAP-TYPE .1.3.6.1.4.1.4329.20.1.1.1.0.1752 |
snMspsTrapWlanOverlapApAgedOutOverlap-AP aged out TRAP-TYPE .1.3.6.1.4.1.4329.20.1.1.1.0.1753 |
snMspsTrapWlanWdsUpWDS interface is up TRAP-TYPE .1.3.6.1.4.1.4329.20.1.1.1.0.1754 |
snMspsTrapWlanWdsDownWDS interface is down TRAP-TYPE .1.3.6.1.4.1.4329.20.1.1.1.0.1755 |
snMspsTrapWlanRadarDetectedDFS radar interference event occured TRAP-TYPE .1.3.6.1.4.1.4329.20.1.1.1.0.1756 |
snMspsTrapWlanRadarAgedOutDFS channel aged out TRAP-TYPE .1.3.6.1.4.1.4329.20.1.1.1.0.1757 |
snMspsTrapWlanRadiusAccessAcceptedRADIUS: access from a client accepted TRAP-TYPE .1.3.6.1.4.1.4329.20.1.1.1.0.1758 |
snMspsTrapWlanRadiusAccessRejectedRADIUS: access request from a client rejected TRAP-TYPE .1.3.6.1.4.1.4329.20.1.1.1.0.1759 |
snMspsTrapWlanAuthToAPFailedClient: Authentication on AP failed TRAP-TYPE .1.3.6.1.4.1.4329.20.1.1.1.0.1761 |
snMspsTrapWlanAssociatedToAPClient: successfully associated to AP TRAP-TYPE .1.3.6.1.4.1.4329.20.1.1.1.0.1763 |
snMspsTrapWlanAssociationToAPFailedClient: Association failed TRAP-TYPE .1.3.6.1.4.1.4329.20.1.1.1.0.1764 |
snMspsTrapWlanDisassociatedFromAPClient: disassociated from AP TRAP-TYPE .1.3.6.1.4.1.4329.20.1.1.1.0.1765 |
snMspsTrapWlanDisassociationFromAPFailedClient: Disassotiation failed TRAP-TYPE .1.3.6.1.4.1.4329.20.1.1.1.0.1766 |
snMspsTrapWlanAuthenticationFromClientFailedAP: Client authentication failed TRAP-TYPE .1.3.6.1.4.1.4329.20.1.1.1.0.1767 |
snMspsTrapWlanClientDeauthenticatedClient: deauthenticated from AP TRAP-TYPE .1.3.6.1.4.1.4329.20.1.1.1.0.1768 |
snMspsTrapWlanClientAuthenticatedClient: authenticated to AP TRAP-TYPE .1.3.6.1.4.1.4329.20.1.1.1.0.1769 |
snMspsTrapWlanClientAssociatedClient: associated to AP TRAP-TYPE .1.3.6.1.4.1.4329.20.1.1.1.0.1770 |
snMspsTrapWlanAssociationFromClientFailedAP: Client association failed TRAP-TYPE .1.3.6.1.4.1.4329.20.1.1.1.0.1771 |
snMspsTrapWlanClientDisassociatedClient: disassociated from AP TRAP-TYPE .1.3.6.1.4.1.4329.20.1.1.1.0.1772 |
snMspsTrapWlanDisassociationFromClientFailedAP: Client disassociation failed TRAP-TYPE .1.3.6.1.4.1.4329.20.1.1.1.0.1773 |
snMspsTrapWlanForcedRoamingForced Roaming event occured TRAP-TYPE .1.3.6.1.4.1.4329.20.1.1.1.0.1774 |
snMspsTrapWlanIPCFMaxStaiPCF: number of wireless clients too big for the cycle time TRAP-TYPE .1.3.6.1.4.1.4329.20.1.1.1.0.1781 |
snMspsTrapWlanIPCFMaxCycleTimeiPCF: Max. PROFINET cycle time exceeded TRAP-TYPE .1.3.6.1.4.1.4329.20.1.1.1.0.1782 |
snMspsTrapWlanIPCFMaxCyclicPollSizeMax. size of PROFINET cyclic poll exceeded (too many PROFINET devices) TRAP-TYPE .1.3.6.1.4.1.4329.20.1.1.1.0.1783 |
snMspsTrapPowerLine1DownPower down on line L1. TRAP-TYPE .1.3.6.1.4.1.4329.20.1.1.1.0.1851 |
snMspsTrapPowerLine1UpPower up on line L1. TRAP-TYPE .1.3.6.1.4.1.4329.20.1.1.1.0.1852 |
snMspsTrapPowerLine2DownPower down on line L2. TRAP-TYPE .1.3.6.1.4.1.4329.20.1.1.1.0.1853 |
snMspsTrapPowerLine2UpPower up on line L2. TRAP-TYPE .1.3.6.1.4.1.4329.20.1.1.1.0.1854 |
snMspsTrapChangedFaultStateDevice changed fault state. TRAP-TYPE .1.3.6.1.4.1.4329.20.1.1.1.0.1855 |
snMspsTrapPoEDownPower down on line 3 (PoE). TRAP-TYPE .1.3.6.1.4.1.4329.20.1.1.1.0.1856 |
snMspsTrapPoEUpPower up on line L3 (PoE). TRAP-TYPE .1.3.6.1.4.1.4329.20.1.1.1.0.1857 |
snMspsTrapEnvDataThe device entered an considerable temperature / usage value.
Variable Bindigs: Message what happened TRAP-TYPE .1.3.6.1.4.1.4329.20.1.1.1.0.1860 |
snMspsTrapServiceInformationService Information occured. Variable Bindigs: Message what happened TRAP-TYPE .1.3.6.1.4.1.4329.20.1.1.1.0.1861 |
snMspsTrapCLIScriptFileStatusThis trap is generated when a CLI script file was successfully loaded via TFTP and the file transfer was triggered through DHCP Options 66/67 TRAP-TYPE .1.3.6.1.4.1.4329.20.1.1.1.0.1862 |
snMspsTrapConfigurationChangeInforms user when configuration is changed TRAP-TYPE .1.3.6.1.4.1.4329.20.1.1.1.0.1863 |
snMspsTrapNTPInvalidConfigurationInvalid NTP Configuration. TRAP-TYPE .1.3.6.1.4.1.4329.20.1.1.1.0.2101 |
snMspsTrapNTPWrongPacketLengthReceived NTP Packet with wrong length. TRAP-TYPE .1.3.6.1.4.1.4329.20.1.1.1.0.2102 |
snMspsTrapNTPWrongSourceAddressReceived NTP Packet from wrong Source Address. TRAP-TYPE .1.3.6.1.4.1.4329.20.1.1.1.0.2103 |
snMspsTrapNTPWrongKeyIdReceived NTP Packet with wrong or missing Key Id. TRAP-TYPE .1.3.6.1.4.1.4329.20.1.1.1.0.2104 |
snMspsTrapNTPAddAuthFailSecure NTP failed to add authentication. TRAP-TYPE .1.3.6.1.4.1.4329.20.1.1.1.0.2105 |
snMspsTrapNTPVerifyAuthFailReceived NTP Packet failed authentication. TRAP-TYPE .1.3.6.1.4.1.4329.20.1.1.1.0.2106 |
snMspsTrapNTPKeyUpdateSecureNTP Keys were updated. TRAP-TYPE .1.3.6.1.4.1.4329.20.1.1.1.0.2107 |
snMspsTrapVRRPStateChangeDevice changed vrrp master state. TRAP-TYPE .1.3.6.1.4.1.4329.20.1.1.1.0.2201 |
snMspsTrapLOOPDStateChangeDevice changed LOOPD state. TRAP-TYPE .1.3.6.1.4.1.4329.20.1.1.1.0.2251 |
snMspsTrapOSPFStateChangeDevice changed OSPF route state. TRAP-TYPE .1.3.6.1.4.1.4329.20.1.1.1.0.2301 |
snMspsTrapMNMobileConnectionSuccessMobile connection successfull. TRAP-TYPE .1.3.6.1.4.1.4329.20.1.1.1.0.2351 |
snMspsTrapMNMobileConnectionFailureMobile connection failed. TRAP-TYPE .1.3.6.1.4.1.4329.20.1.1.1.0.2352 |
snMspsTrapMNMobileConnectionLostMobile connection lost. TRAP-TYPE .1.3.6.1.4.1.4329.20.1.1.1.0.2353 |
snMspsTrapDigitalIOStateChangeDigital IO pin state change detected. TRAP-TYPE .1.3.6.1.4.1.4329.20.1.1.1.0.2851 |
snTrapMspsLinkCheckBrokenLinkDetectedLink Check disabled port because of broken link. TRAP-TYPE .1.3.6.1.4.1.4329.20.1.1.1.0.2901 |
snTrapMspsLinkCheckPortEnabledBy Link Check disabled port is enabled again. TRAP-TYPE .1.3.6.1.4.1.4329.20.1.1.1.0.2902 |
snTrapMspsLinkCheckMultiplePartnersLink Check detected multiple partners on port. TRAP-TYPE .1.3.6.1.4.1.4329.20.1.1.1.0.2903 |
snTrapMspsLinkCheckMultiplePartnersResetLink Check partner detection reset on port. TRAP-TYPE .1.3.6.1.4.1.4329.20.1.1.1.0.2904 |
snTrapMspsLinkCheckCriticalLinkDetectedLink Check indicates critical link state on port. TRAP-TYPE .1.3.6.1.4.1.4329.20.1.1.1.0.2905 |
snTrapMspsLinkCheckCriticalLinkResetBy Link Check indicated critical link state reset on port. TRAP-TYPE .1.3.6.1.4.1.4329.20.1.1.1.0.2906 |
snTrapMspsLinkCheckUnapprovedConfigDetectedUnapproved Link Check configuration. Disable Link Check on this port. TRAP-TYPE .1.3.6.1.4.1.4329.20.1.1.1.0.2907 |
snTrapMspsLinkCheckUnapprovedConfigResolvedUnapproved Link Check configuration resolved on this port. TRAP-TYPE .1.3.6.1.4.1.4329.20.1.1.1.0.2908 |
snMspsTrapMrpInterconMgrOpenStateMRP Interconnection state change to open. TRAP-TYPE .1.3.6.1.4.1.4329.20.1.1.1.0.3001 |
snMspsTrapMrpInterconMgrClosedStateMRP Interconnection state change to closed. TRAP-TYPE .1.3.6.1.4.1.4329.20.1.1.1.0.3002 |
snMspsTrapPoeStateChangePoe state change notification. TRAP-TYPE .1.3.6.1.4.1.4329.20.1.1.1.0.3051 |
snMspsCommon OBJECT IDENTIFIER .1.3.6.1.4.1.4329.20.1.1.1.1 |
snMspsConfig OBJECT IDENTIFIER .1.3.6.1.4.1.4329.20.1.1.1.1.1 |
snMspsConfigLoginAuthenticationConfigures the mechanism by which the user login has to be authenticated
for accessing the GUI to manage the switch. Authentication is done
either locally or in the remote side through a RADIUS Server or TACACS.
If Authentication is configured as radiusLocal or tacacsLocal then
Local authentication provides a back door or a secondary option
for authentication if the server fails.rw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.1.1 |
snMspsConfigCtrlTableA table to control device features like egress traffic control,
stats collection, etc. either for the entire switch or for each
interface in the switch. SEQUENCE OF SnMspsConfigCtrlEntry .1.3.6.1.4.1.4329.20.1.1.1.1.1.2 |
snMspsConfigCtrlEntryAn entry appears in this table for each interface in the system.
In addition to that an entry with index '0' is created in this
table by default.
If 'snMspsConfigCtrlStatus' of the entry '0' is made 'valid', then
global control is chosen and the values against entry '0' is
applicable for all the interfaces of the switch.
If 'snMspsConfigCtrlStatus' of the entry '0' is made 'invalid',
then interface-wise control is chosen & the values against each
interface index is applicable for that interface.
At a particular point of time, either global control will be
applicable or interface-wise control is applicable.
Both will not be considered together.
Index to the table is the interface index of the port. SnMspsConfigCtrlEntry .1.3.6.1.4.1.4329.20.1.1.1.1.1.2.1 |
snMspsConfigCtrlIndexInterface index of the port for which the configuration
in this entry applies.
If any configuration is made in this table for the index '0',
that configuration will be considered as global configuration
and is applicable for all the interfaces of the switch. Integer32 .1.3.6.1.4.1.4329.20.1.1.1.1.1.2.1.1 |
snMspsConfigCtrlEgressStatusControls the transmission of egress traffic over this interface.
This value for entry '0' controls the egress traffic over all
interfaces.rw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.1.2.1.2 |
snMspsConfigCtrlStatsCollectionEnables or disables statistics collection for this interface.
This value for entry '0' controls the stats collection for all
interfaces.rw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.1.2.1.3 |
snMspsConfigCtrlStatusSpeficies the validity of the entry.
If the 'Config Control Status' for entry '0' is made 'valid',
then global control is chosen in the system.
It signifies that the values against entry '0' is applicable
for all the interfaces of the switch.
If the 'Config Control Status' for entry '0' is made 'invalid',
then interface-wise control is chosen.
Then the values against each interface index is applicable
for that interface.
By default, 'snMspsConfigCtrlStatus' will be 'invalid' for
entry '0' and 'valid' for all other entries.
(ie) by default, interface-wise configuration is enabled
in the system.
The status of entries other than the zeroth(0th) entry can not be
made 'invalid'.rw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.1.2.1.4 |
snMspsConfigRateCtrlTableA table to control the rate limiting parameters
either for the entire switch or for each physical and port-channel
interface in the switch. SEQUENCE OF SnMspsConfigRateCtrlEntry .1.3.6.1.4.1.4329.20.1.1.1.1.1.3 |
snMspsConfigRateCtrlEntryAn entry appears in this table for each physical and port-channel
interface in the switch. SnMspsConfigRateCtrlEntry .1.3.6.1.4.1.4329.20.1.1.1.1.1.3.1 |
snMspsConfigRateCtrlIndexThe interface index for which the configuration in this
entry applies. Integer32 .1.3.6.1.4.1.4329.20.1.1.1.1.1.3.1.1 |
snMspsConfigRateCtrlDLFLimitValueAllows to configure the limiting value for the maximum number
of dlf data that can be transmitted per second over this interface.
The unit of data is given by snMspsConfigRateCtrlUnit object.
Setting this object to the value zero disables rate limiting for
Destination lookup failure packets on this interface. The value that
can be set for this object is limited by the underlying hardwarerw Integer32 .1.3.6.1.4.1.4329.20.1.1.1.1.1.3.1.2 |
snMspsConfigRateCtrlBCASTLimitValueAllows to configure the limiting value for the maximum number
of broadcast data that can be transmitted per second over this
interface. The unit of data is given by snMspsConfigRateCtrlUnit object.
Setting this object to the value zero disables rate
limiting for Broadcast packets on this interface. The value that
can be set for this object is limited by the underlying hardwarerw Integer32 .1.3.6.1.4.1.4329.20.1.1.1.1.1.3.1.3 |
snMspsConfigRateCtrlMCASTLimitValueAllows to configure the limiting value for the maximum number
of multicast data that can be transmitted per second over this
interface. The unit of data is given by snMspsConfigRateCtrlUnit object.
Setting this object to the value zero disables rate
limiting for Multicast packets on this interface. The value that
can be set for this object is limited by the underlying hardwarerw Integer32 .1.3.6.1.4.1.4329.20.1.1.1.1.1.3.1.4 |
snMspsConfigRateCtrlPortRateLimitConfigures interface Rate Limit (Packet that can be transferred
on a port at a particular second).
This object's value will take effect on the interface speed. Based
on the operating speed of the port, the rate limit will be applied.
This value can also be affected by the metering. A value of zero(0)
disable rate limiting i.e. sets the port to full speed.rw Integer32 .1.3.6.1.4.1.4329.20.1.1.1.1.1.3.1.5 |
snMspsConfigRateCtrlPortBurstSizeConfigures interface Burst Pkt Rate. (Packet Burst that can be
transferred on a port at a particular second)
This object's value will take effect on the interface speed. Based
on the operating speed of the port, the burst size of the port
will be applied. This value can also be affected by the metering. A
value of zero(0) disable burst rate limiting i.e. sets the port burst
rate limit to full speed.rw Integer32 .1.3.6.1.4.1.4329.20.1.1.1.1.1.3.1.6 |
snMspsConfigRateCtrlUCASTLimitValueAllows to configure the limiting value for the maximum number
of unicast data that can be transmitted per second over this
interface. The unit of data is given by snMspsConfigRateCtrlUnit object.
Setting this object to the value zero disables rate
limiting for Multicast packets on this interface. The value that
can be set for this object is limited by the underlying hardwarerw Integer32 .1.3.6.1.4.1.4329.20.1.1.1.1.1.3.1.7 |
snMspsConfigAclRateCtrlTableA table to control the rate limiting parameters
either for the entire switch or for each physical and port-channel
interface in the switch. Chip-Dependent! SEQUENCE OF SnMspsConfigAclRateCtrlEntry .1.3.6.1.4.1.4329.20.1.1.1.1.1.4 |
snMspsConfigAclRateCtrlEntryAn entry appears in this table for each physical and port-channel
interface in the switch. SnMspsConfigAclRateCtrlEntry .1.3.6.1.4.1.4329.20.1.1.1.1.1.4.1 |
snMspsConfigAclRateCtrlIndexThe interface index for which the configuration in this
entry applies. Integer32 .1.3.6.1.4.1.4329.20.1.1.1.1.1.4.1.1 |
snMspsConfigAclRateCtrlDLFLimitValueAllows to configure the limiting value for the maximum number
of dlf packets that can be transmitted per second over this interface.
Setting this object to the value zero disables rate limiting for
Destination lookup failure packets on this interface. The value that
can be set for this object is limited by the underlying hardwarerw Integer32 .1.3.6.1.4.1.4329.20.1.1.1.1.1.4.1.2 |
snMspsConfigAclRateCtrlBCASTLimitValueAllows to configure the limiting value for the maximum number
of broadcast packets that can be transmitted per second over this
interface. Setting this object to the value zero disables rate
limiting for Broadcast packets on this interface. The value that
can be set for this object is limited by the underlying hardwarerw Integer32 .1.3.6.1.4.1.4329.20.1.1.1.1.1.4.1.3 |
snMspsConfigAclRateCtrlMCASTLimitValueAllows to configure the limiting value for the maximum number
of multicast packets that can be transmitted per second over this
interface. Setting this object to the value zero disables rate
limiting for Multicast packets on this interface. The value that
can be set for this object is limited by the underlying hardwarerw Integer32 .1.3.6.1.4.1.4329.20.1.1.1.1.1.4.1.4 |
snMspsConfigAclRateCtrlPortRateLimitConfigures interface Rate Limit (Packet that can be transferred
on a port at a particular second).
This object's value will take effect on the interface speed. Based
on the operating speed of the port, the rate limit will be applied.
This value can also be affected by the metering. A value of zero(0)
disable rate limiting i.e. sets the port to full speed.rw Integer32 .1.3.6.1.4.1.4329.20.1.1.1.1.1.4.1.5 |
snMspsConfigAclRateCtrlPortBurstSizeConfigures interface Burst Pkt Rate. (Packet Burst that can be
transferred on a port at a particular second)
This object's value will take effect on the interface speed. Based
on the operating speed of the port, the burst size of the port
will be applied. This value can also be affected by the metering. A
value of zero(0) disable burst rate limiting i.e. sets the port burst
rate limit to full speed.rw Integer32 .1.3.6.1.4.1.4329.20.1.1.1.1.1.4.1.6 |
snMspsConfigPortCtrlTableA table to control the port specific parameters of the device like speed,
duplex mode, etc. SEQUENCE OF SnMspsConfigPortCtrlEntry .1.3.6.1.4.1.4329.20.1.1.1.1.1.5 |
snMspsConfigPortCtrlEntryAn entry appears in this table for each interface in the system.
Index to the table is the interface index of the port. SnMspsConfigPortCtrlEntry .1.3.6.1.4.1.4329.20.1.1.1.1.1.5.1 |
snMspsConfigPortCtrlIndexInterface index of the port for which the configuration
in this entry applies. Integer32 .1.3.6.1.4.1.4329.20.1.1.1.1.1.5.1.1 |
snMspsConfigPortCtrlModeSpeficies the mode in which the speed, duplex modes and flow control
of the interface is determined.
If set as 'auto', the hardware senses speed and negotiates with the port
on the other end of the link for data transfer operation as
'full-duplex' or 'half-duplex' and about flow contol.
If set as 'nonegotiation', the configured values for interface
speed, duplex mode and flow control will be effective.rw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.1.5.1.2 |
snMspsConfigPortCtrlDuplexConfigures interface data transfer mode as full-duplex or half-duplex.
This object can be configured only if the 'PortCtrlMode' is 'nonegotiation'.
If the 'PortCtrlMode' is 'auto', it obtains the value from Hardware
after negotiating with its peerrw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.1.5.1.3 |
snMspsConfigPortCtrlSpeedConfigures interface speed.
This object can be configured only if the 'PortCtrlMode' is 'nonegotiation'.
If the 'PortCtrlMode' is 'auto', it obtains the value from Hardware
after negotiating with its peerrw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.1.5.1.4 |
snMspsConfigPortCtrlFlowControlEnables / disables flow control for the interface.
This object be configured only if the 'PortCtrlMode' is 'nonegotiation'.
If the 'PortCtrlMode' is 'auto', it obtains the value from Hardware
after negotiating with its peerrw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.1.5.1.5 |
snMspsConfigPortCtrlRenegotiateWhen configured as 'true', restarts autonegotiation on the interface.
Once autonegotiation is restarted, the value of this object reverts
to 'false'.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4329.20.1.1.1.1.1.5.1.6 |
snMspsConfigPortCtrlMaxMacAddrSpecifies the maximum number of new MAC addresses that can be
learnt over the interface.rw Integer32 .1.3.6.1.4.1.4329.20.1.1.1.1.1.5.1.7 |
snMspsConfigPortCtrlMaxMacActionSpecifies the action to be taken when the maximum number of new MAC
addresses that can be learnt over the interface is exceeded.
If the action is 'drop', the packet with new mac address will be
dropped once the maximum number of new MAC addresses that can be
learnt over the interface is exceeded.
If the action is 'purgeLRU', the 'Least Recently Used' mac address
will be deleted from the MAC table and the new mac address will be
added.rw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.1.5.1.8 |
snMspsConfigPortHOLBlockPreventionEnables or disables Head-Of-Line Blocking prevention on a port.rw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.1.5.1.9 |
snMspsConfigMirror OBJECT IDENTIFIER .1.3.6.1.4.1.4329.20.1.1.1.1.1.6 |
snMspsConfigMirrorStatusThis object is used to enable/disable mirroring
feature in hardware.
When set to 'disabled (1)', all mirroring configurations will be
removed from hardware.
When set to 'enabled (2)', all mirroring configurations
present in software will be programmed in hardware.rw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.1.6.1 |
snMspsConfigMirrorToPortSpecifies the port to which the active mirrored traffic controlled
by snMspsConfigMirrorCtrlTable is to be copied.rw Integer32 .1.3.6.1.4.1.4329.20.1.1.1.1.1.6.2 |
snMspsConfigMirrorCtrlTableA table to control mirroring features for each interface
in the switch.
Parameters in this table are valid only when the
'snMspsConfigMirrorStatus' for the switch is not 'disabled'. SEQUENCE OF SnMspsConfigMirrorCtrlEntry .1.3.6.1.4.1.4329.20.1.1.1.1.1.6.3 |
snMspsConfigMirrorCtrlEntryAn entry appears in this table for each interface
in the system. SnMspsConfigMirrorCtrlEntry .1.3.6.1.4.1.4329.20.1.1.1.1.1.6.3.1 |
snMspsConfigMirrorCtrlIndexThe interface index of the port for which the configuration
in this entry applies. Integer32 .1.3.6.1.4.1.4329.20.1.1.1.1.1.6.3.1.1 |
snMspsConfigMirrorCtrlIngressMirroringProvides control to enable or disable mirroring of ingress
traffic over this interface to the mirrored-to port.rw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.1.6.3.1.2 |
snMspsConfigMirrorCtrlEgressMirroringProvides control to enable or disable mirroring of egress
traffic over this interface to the mirrored-to port.rw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.1.6.3.1.3 |
snMspsConfigMirrorCtrlStatusSpecifies the validity of the entry.rw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.1.6.3.1.4 |
snMspsConfigMirrorCtrlExtnTableThis Table is used to configure advanced mirroring features like
- Port Based Mirroring:
- flow based mirroring
- vlan based mirroring
Following are the configuration details for Port based mirroring:
To configure source ports in a session
- snMspsConfigMirrorCtrlExtnMirrType - is set to portBased
- snMspsConfigMirrorCtrlExtnSrcTable - should be used to configure list
of source ports to be mirrored
in a session
- snMspsConfigMirrorCtrlExtnSrcId - represents the source port.
The port Id to be mirrored
should be given here.
- snMspsConfigMirrorCtrlExtnSrcCfg - this object is used to
add/remove a port in the
source port list
Example
To create a session 1 with source ports 5,6 following
sequence of configuration should be followed
For table snMspsConfigMirrorCtrlExtnTable
snMspsConfigMirrorCtrlExtnSessionIndex = 1 as index
snMspsConfigMirrorCtrlExtnMirrType = portBased
For table snMspsConfigMirrorCtrlExtnSrcTable
snMspsConfigMirrorCtrlExtnSessionIndex = 1 as index
snMspsConfigMirrorCtrlExtnSrcId = 5 as index
snMspsConfigMirrorCtrlExtnSrcCfg = add
snMspsConfigMirrorCtrlExtnSessionIndex = 1 as index
snMspsConfigMirrorCtrlExtnSrcId = 6 as index
snMspsConfigMirrorCtrlExtnSrcCfg = add
To configure destination ports in a session
- snMspsConfigMirrorCtrlExtnDestinationTable - should be used to
configure list of
destination ports to be
mirrored in a session
- snMspsConfigMirrorCtrlExtnDestination - represents the
destination port. The
port Id to which packets
should be mirrored should
be given here.
- snMspsConfigMirrorCtrlExtnDestCfg - this object is used to
add/remove a port in the
source port list.
Example
To create a session 1 with destination port 10,11 following
sequence of configuration should be followed
For table snMspsConfigMirrorCtrlExtnTable
snMspsConfigMirrorCtrlExtnSessionIndex = 1 as index
snMspsConfigMirrorCtrlExtnMirrType = portBased
For table snMspsConfigMirrorCtrlExtnDestinationTable
snMspsConfigMirrorCtrlExtnSessionIndex = 1 as index
snMspsConfigMirrorCtrlExtnDestination = 10 as index
snMspsConfigMirrorCtrlExtnDestCfg = add
snMspsConfigMirrorCtrlExtnSessionIndex = 1 as index
snMspsConfigMirrorCtrlExtnDestination = 11 as index
snMspsConfigMirrorCtrlExtnDestCfg = add
To Activate a session
- snMspsConfigMirrorCtrlExtnStatus - should be used to
activate/deactivate mirroring for a
session
Example
To enable mirroring for a session following sequence of
configuration should be followed
For table snMspsConfigMirrorCtrlExtnTable
snMspsConfigMirrorCtrlExtnSessionIndex = 1 as index
snMspsConfigMirrorCtrlExtnStatus = active
Above configurations applies to flow based mirroring also, the
snMspsConfigMirrorCtrlExtnSrcId used above for configuratin ports
should be used to configure flow Id
To enable remote monitoring of sources for a session
- snMspsConfigMirrorCtrlExtnRSpanStatus - should be used to
enable/disable remote
monitoring for a session
it can be used to set a
session as source rspan
session which implies source
entities for this session are
monitored remotely or can be
used to set a session
as destination rspan session
which implies that mirrored
data is received for this
session should be forwarded to
destination entities of this
session
- snMspsConfigMirrorCtrlExtnRSpanVlanId - it is the vlan id which is
reserved in the network to
carry Mirrored data,if the
session is configured as
source rspan session then data
mirrored for the source
entities will be forwarded on
this vlan if the session is
configured as destination
rspan session then data
received on this vlan will be
forwarded to the destination
entities of this session
Following are the configuration details for configurating Vlan
based mirroring:
To configure vlans as source for a session
- snMspsConfigMirrorCtrlExtnMirrType - is set to vlanBased
- snMspsConfigMirrorCtrlExtnSrcVlanTable - should be used to configure
list of source vlans to be
mirrored in a session
- snMspsConfigMirrorCtrlExtnSrcVlanId - represents a source vlan. The
vlan to be mirrored should be
given here.
- snMspsConfigMirrorCtrlExtnSrcVlanCfg - this object is used to
add/remove a vlan in the
source vlan list
Example
To create a session 1 with source list as vlan 5,6
belonging to context 1 following sequence of configuration
should be followed
For table snMspsConfigMirrorCtrlExtnTable
snMspsConfigMirrorCtrlExtnSessionIndex = 1 as index
snMspsConfigMirrorCtrlExtnMirrType = vlanBased
For table snMspsConfigMirrorCtrlExtnSrcVlanTable
snMspsConfigMirrorCtrlExtnSrcVlanContext = 1 as index
snMspsConfigMirrorCtrlExtnSessionIndex = 1 as index
snMspsConfigMirrorCtrlExtnSrcVlanId = 5 as index
snMspsConfigMirrorCtrlExtnSrcVlanCfg = add
snMspsConfigMirrorCtrlExtnSrcVlanContext = 1 as index
snMspsConfigMirrorCtrlExtnSessionIndex = 1 as index
snMspsConfigMirrorCtrlExtnSrcVlanId = 6 as index
snMspsConfigMirrorCtrlExtnSrcVlanCfg = add
Entries for this table can be configured only when snMspsConfigMirrorStatus
is set to enabled.
Configurations done through 'snMspsConfigMirrorCtrlTable' will change the
following for the first session on this table:
- Mirroring type will be changed to port-based
- Mode and Source entities will be overwritten
with the values configured through 'snMspsConfigMirrorCtrlTable'
- Destination entities will be overwritten
with the value configured through 'snMspsConfigMirrorToPort' object SEQUENCE OF SnMspsConfigMirrorCtrlExtnEntry .1.3.6.1.4.1.4329.20.1.1.1.1.1.6.6 |
snMspsConfigMirrorCtrlExtnEntryAn entry appears in this table for each session
in the system. SnMspsConfigMirrorCtrlExtnEntry .1.3.6.1.4.1.4329.20.1.1.1.1.1.6.6.1 |
snMspsConfigMirrorCtrlExtnSessionIndexThe index of the mirroring session for which the configuration
in this entry applies. Integer32 .1.3.6.1.4.1.4329.20.1.1.1.1.1.6.6.1.1 |
snMspsConfigMirrorCtrlExtnMirrTypeThis object tells the type of mirroring this session supports.
This object needs to be set before doing any configuration for
a mirroring sessionrw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.1.6.6.1.2 |
snMspsConfigMirrorCtrlExtnRSpanStatusThis object indicates session is enabled or disabled for
Remote monitoring.
If set as 'source-rspan-vlanid' indicates that the session is
enabled for Remote monitoring and the source entities for this
session will be remotely monitored.
If set as 'destination-rspan-vlanid' indicates that the session
should monitor remote traffic mirrored with RSPAN VLAN ID tag.
RSPAN VLAN ID should be configured through object
'snMspsConfigMirrorCtrlExtnRSpanVlanId'.
If set as 'disabled' Remote monitoring is disabled for this
mirroring session.rw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.1.6.6.1.3 |
snMspsConfigMirrorCtrlExtnRSpanVlanIdVlan Id used for Remote monitoring for this session.
If snMspsConfigMirrorCtrlExtnRSpanStatus is set to disabled, then
this object will have an invalid value (zero)rw Integer32 .1.3.6.1.4.1.4329.20.1.1.1.1.1.6.6.1.4 |
snMspsConfigMirrorCtrlExtnRSpanContextSpecifies the Context Id to which the RSpan Vlan belongs.
Value '0' mean this object is not considered for this
mirroring session.rw Integer32 .1.3.6.1.4.1.4329.20.1.1.1.1.1.6.6.1.5 |
snMspsConfigMirrorCtrlExtnStatusThis object indicates the status of the entry. The entry can be
made active only if snMspsConfigMirrorCtrlExtnMirrType is configured and
source and destination entries for this sesion is also configuredrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.4329.20.1.1.1.1.1.6.6.1.6 |
snMspsConfigMirrorCtrlExtnHardwareIndexSpecifies the Hardware Index associated with this mirroring session.
Value '0' mean this object is not applicable for this
mirroring session.ro Integer32 .1.3.6.1.4.1.4329.20.1.1.1.1.1.6.6.1.7 |
snMspsConfigMirrorCtrlExtnSrcTableA table to configure list of source entities for mirroring sessions SEQUENCE OF SnMspsConfigMirrorCtrlExtnSrcEntry .1.3.6.1.4.1.4329.20.1.1.1.1.1.6.7 |
snMspsConfigMirrorCtrlExtnSrcEntryAn entry appears in this table for each mirroring session. SnMspsConfigMirrorCtrlExtnSrcEntry .1.3.6.1.4.1.4329.20.1.1.1.1.1.6.7.1 |
snMspsConfigMirrorCtrlExtnSrcIdSpecifies the source id which participates in a mirroring session.
For Port based mirroring this object can be port IfIndex.
To mirror Tunnel and Trunk ports the same Id can be used for
specifying Tunnel/Trunk Id.
For Flow based mirroring this object can be Acl Ids. Integer32 .1.3.6.1.4.1.4329.20.1.1.1.1.1.6.7.1.1 |
snMspsConfigMirrorCtrlExtnSrcCfgThis object is used to create/delete a source entry for a session.rw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.1.6.7.1.2 |
snMspsConfigMirrorCtrlExtnSrcModeProvides control to set the mode of mirroring.
It can be ingerss,Egress or Both.rw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.1.6.7.1.3 |
snMspsConfigMirrorCtrlExtnSrcVlanTableA table to configure list of vlan source entities for mirroring sessions SEQUENCE OF SnMspsConfigMirrorCtrlExtnSrcVlanEntry .1.3.6.1.4.1.4329.20.1.1.1.1.1.6.8 |
snMspsConfigMirrorCtrlExtnSrcVlanEntryAn entry appears in this table for each mirroring session. SnMspsConfigMirrorCtrlExtnSrcVlanEntry .1.3.6.1.4.1.4329.20.1.1.1.1.1.6.8.1 |
snMspsConfigMirrorCtrlExtnSrcVlanContextSpecifies the Context Id to which the source entity belongs, this
is used in case of specifying vlan as source.
Value '-1' mean this object is not considered for this mirroring
session. Integer32 .1.3.6.1.4.1.4329.20.1.1.1.1.1.6.8.1.1 |
snMspsConfigMirrorCtrlExtnSrcVlanIdSpecifies the Vlan id which participates in a mirroring session. Integer32 .1.3.6.1.4.1.4329.20.1.1.1.1.1.6.8.1.2 |
snMspsConfigMirrorCtrlExtnSrcVlanCfgThis object is used to create/delete a vlan entry for a session.rw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.1.6.8.1.3 |
snMspsConfigMirrorCtrlExtnSrcVlanModeProvides control to set the mode of mirroring.
It can be ingerss,Egress or Both.rw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.1.6.8.1.4 |
snMspsConfigMirrorCtrlExtnDestinationTableA table to configure list of destination entities SEQUENCE OF SnMspsConfigMirrorCtrlExtnDestinationEntry .1.3.6.1.4.1.4329.20.1.1.1.1.1.6.9 |
snMspsConfigMirrorCtrlExtnDestinationEntryAn entry appears in this table for each destination entity
in a mirroring session. SnMspsConfigMirrorCtrlExtnDestinationEntry .1.3.6.1.4.1.4329.20.1.1.1.1.1.6.9.1 |
snMspsConfigMirrorCtrlExtnDestinationSpecifies the destination port id which participates in a mirroring
session. Integer32 .1.3.6.1.4.1.4329.20.1.1.1.1.1.6.9.1.1 |
snMspsConfigMirrorCtrlExtnDestCfgThis object is used to create/delete a destination entry for a session.rw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.1.6.9.1.2 |
snMspsConfigNetwork OBJECT IDENTIFIER .1.3.6.1.4.1.4329.20.1.1.1.1.1.7 |
snMspsConfigL2FilterTableA table to configure L2 filter rules in the system. SEQUENCE OF SnMspsConfigL2FilterEntry .1.3.6.1.4.1.4329.20.1.1.1.1.1.7.1 |
snMspsConfigL2FilterEntryEach entry in this table is a L2 filter rule.
Index to the table is the L2 filter number. SnMspsConfigL2FilterEntry .1.3.6.1.4.1.4329.20.1.1.1.1.1.7.1.1 |
snMspsConfigL2FilterNoL2 Filter rule number. Integer32 .1.3.6.1.4.1.4329.20.1.1.1.1.1.7.1.1.1 |
snMspsConfigL2FilterPriorityThe priority of the L2 filter can be used to decide which filter rule
is applicable when
Higher value of 'filter priority' implies a higher priority.
Usage of 'L2FilterPriority' is implementation dependant.rw Integer32 .1.3.6.1.4.1.4329.20.1.1.1.1.1.7.1.1.2 |
snMspsConfigL2FilterEtherTypeThe value in the Type/Len field of a frame that will
be matched to trigger this filter. The default value of
this object is '0'. When this object is SET with the default
value, frames are not matched for the value in the Type/Len
field with the value set for this object.rw Integer32 .1.3.6.1.4.1.4329.20.1.1.1.1.1.7.1.1.3 |
snMspsConfigL2FilterProtocolTypeSpecifies the non IP protocol type to be filtered.
aarp | amber | dec-spanning | decnet-iv |
diagnostic | dsm |etype-6000 | etype-8042 |
lat | lavc-sca | mop-console | mop-dump |
msdos | mumps | netbios | vines-echo |
vines-ip | xns-idp: A non-IP protocol.
A value of '0' means, the filter is applicable for all protocols.rw Unsigned32 .1.3.6.1.4.1.4329.20.1.1.1.1.1.7.1.1.4 |
snMspsConfigL2FilterDstMacAddrDestination MAC address to be matched with the packet. By Default, the
Destination Mac Address will be zero which means dont care condition ie)
any Dst Mac Address .rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.4329.20.1.1.1.1.1.7.1.1.5 |
snMspsConfigL2FilterSrcMacAddrSource MAC address to be matched with the packet. By Default, the Source
Mac Address will be zero which means dont care condition ie) any Src Mac
addressrw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.4329.20.1.1.1.1.1.7.1.1.6 |
snMspsConfigL2FilterVlanIdVlan Id to be filtered. In case of Provider bridges, This Vlan Id will
be treated as customer Vlan Id.
A value of '0' means, this object is unused. Configuring this value is not
allowed.rw Integer32 .1.3.6.1.4.1.4329.20.1.1.1.1.1.7.1.1.7 |
snMspsConfigL2FilterInPortListSpecifies the complete set of ports over which this filter is applied
for packets ingress at ports in this list.
If the In port list is '0', the filter rule is applicable for the
incoming packets on all ports.
Even though the snMspsConfigL2FilterInPortList is configured, It is applicable only
if snMspsConfigL2FilterDirection is configured as 'in'.
By default inport list is maintained as '0'.rw PortList (Q-BRIDGE-MIB) .1.3.6.1.4.1.4329.20.1.1.1.1.1.7.1.1.8 |
snMspsConfigL2FilterActionSpecifies the action to be taken on the packet if the filter
rule matches.
If the action is 'allow', the packet will be forwarded according
to the forwarding rules.
If the action is 'drop', the packet will be discarded.rw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.1.7.1.1.9 |
snMspsConfigL2FilterMatchCountNumber of times this filter is matched.ro Counter32 .1.3.6.1.4.1.4329.20.1.1.1.1.1.7.1.1.10 |
snMspsConfigL2FilterStatusThis object indicates the status of this entry. An entry is
created in this table when this object is SET to 'createAndWait'.
The entry in this table is used when the status of this object
is SET 'active'. The entry in this table is not used when this
object is SET 'notInService'. An entry created in this table is
be deleted when this object is SET 'destroy'.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.4329.20.1.1.1.1.1.7.1.1.11 |
snMspsConfigL2FilterOutPortListSpecifies the complete set of ports over which this filter is applied
for packets egress at Ports in this list.
If the Out port list is '0', the filter rule is applicable for the
outgoing packets on all ports.
Even though the snMspsConfigL2FilterOutPortList is configured, It is applicable only
if snMspsConfigL2FilterDirection is configured as 'out'.
By default outport list is maintained as '0'.rw PortList (Q-BRIDGE-MIB) .1.3.6.1.4.1.4329.20.1.1.1.1.1.7.1.1.12 |
snMspsConfigL2FilterDirectionSpecifies the direction of this filter to be applied. By Default the
filter will be applied on ingress direction.
When the direction of this filter is 'in', It is applied on specified
ports of the snMspsConfigL2FilterInPortList.
When the direction of this filter is 'out', It is applied on specified
ports of the snMspsConfigL2FilterOutPortList.rw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.1.7.1.1.13 |
snMspsConfigL4SwitchingFilterTableA table to L4 Switching rules in the system. SEQUENCE OF SnMspsConfigL4SwitchingFilterEntry .1.3.6.1.4.1.4329.20.1.1.1.1.1.7.2 |
snMspsConfigL4SwitchingFilterEntryEach entry in this table is a L4 Switching rule.
Index to the table is L4 filter number. SnMspsConfigL4SwitchingFilterEntry .1.3.6.1.4.1.4329.20.1.1.1.1.1.7.2.1 |
snMspsConfigL4SwitchingFilterNoL4 Switching Filter rule number. Integer32 .1.3.6.1.4.1.4329.20.1.1.1.1.1.7.2.1.1 |
snMspsConfigL4SwitchingProtocolThe type of protocol to be checked against the packet. The
default value is 255. If the value is 255, it means that the
protocol type can be anything and it will not be checked to
decide the action.rw Integer32 .1.3.6.1.4.1.4329.20.1.1.1.1.1.7.2.1.2 |
snMspsConfigL4SwitchingPortNoThe Layer 4 port no. Please note
these ports are the TCP / UDP ports.rw Unsigned32 .1.3.6.1.4.1.4329.20.1.1.1.1.1.7.2.1.3 |
snMspsConfigL4SwitchingCopyToPortThis object is Port to which the packet would be switchedrw Integer32 .1.3.6.1.4.1.4329.20.1.1.1.1.1.7.2.1.4 |
snMspsConfigL4SwitchingFilterStatusThis object indicates the status of this entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.4329.20.1.1.1.1.1.7.2.1.5 |
snMspsConfigIpAuthMgrTableA table to configure IP authorized managers in the system. SEQUENCE OF SnMspsConfigIpAuthMgrEntry .1.3.6.1.4.1.4329.20.1.1.1.1.1.7.3 |
snMspsConfigIpAuthMgrEntryIP Authorized managers, which restricts configuration from specific
workstations only, provides additional security. Each entry in this
table represents rules for particular IP authorized manager. SnMspsConfigIpAuthMgrEntry .1.3.6.1.4.1.4329.20.1.1.1.1.1.7.3.1 |
snMspsConfigIpAuthMgrIpAddrSpecifies either the Network or Host address from which the switch
can be managed.
An address 0.0.0.0 indicates 'Any Manager'. IpAddress .1.3.6.1.4.1.4329.20.1.1.1.1.1.7.3.1.1 |
snMspsConfigIpAuthMgrIpMaskSpecifies the IP address mask to be applied on snMspsConfigIpAuthMgrIpAddr.
Value 0.0.0.0 indicates mask for 'Any Manager'. IpAddress .1.3.6.1.4.1.4329.20.1.1.1.1.1.7.3.1.2 |
snMspsConfigIpAuthMgrPortListSpecifies the port numbers through which the authorized manager can
access the switch.
By default the authorized manager is allowed to access the switch
through all the ports.
If a set of ports are configured in the 'PortList', the manager can
access the switch only through the configured ports.rw PortList (Q-BRIDGE-MIB) .1.3.6.1.4.1.4329.20.1.1.1.1.1.7.3.1.3 |
snMspsConfigIpAuthMgrVlanListSpecifies the Vlan's in which the IP authorized manager can reside.
By default the manager is allowed to reside in any vlan.
If a set of vlans are configured in the 'VlanList', the manager can
reside only in the configured vlan set. Access to the switch
will be denied from any other vlan.rw OCTET STRING .1.3.6.1.4.1.4329.20.1.1.1.1.1.7.3.1.4 |
snMspsConfigIpAuthMgrOOBPortSpecifies whether the authorized manager can access the switch
through OOB Port
By default the manager is denied access to reside on OOB Interfacerw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4329.20.1.1.1.1.1.7.3.1.5 |
snMspsConfigIpAuthMgrAllowedServicesSpecifies the allowed services through which the authorized manager can
access the switch.
This object takes bit mask values. The services represented by each bit
position is as given below:
With bit 0 being the Least Significant Bit,
Bit0
Bit1
Bit2
Bit3
Bit4
If the particular bit is set to 1,corresponding service is allowed for
the configured manager.
By default all services are allowed for the configured manager.rw Integer32 .1.3.6.1.4.1.4329.20.1.1.1.1.1.7.3.1.6 |
snMspsConfigIpAuthMgrRowStatusThis object indicates the status of this entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.4329.20.1.1.1.1.1.7.3.1.7 |
snMspsConfigIpAuthMgrCreationOrderSpecifies creation order of the rulesrw Integer32 .1.3.6.1.4.1.4329.20.1.1.1.1.1.7.3.1.8 |
snMspsConfigIpAuthMgrEnabledEnable/Disable Ip Authorized Manager.rw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.1.7.4 |
snMspsConfigResetTopologyChgCounterReset topology change counters for RSTP and MSTP depending on the stack running.rw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.1.7.5 |
snMspsConfigIpvxAuthMgrTableA table to configure Ipvx(ipv4 and ipv6) authorized managers in the system. SEQUENCE OF SnMspsConfigIpvxAuthMgrEntry .1.3.6.1.4.1.4329.20.1.1.1.1.1.7.10 |
snMspsConfigIpvxAuthMgrEntryIpvx Authorized managers, which restricts configuration from specific
workstations only, provides additional security. Each entry in this
table represents rules for particular Ipvx authorized manager. SnMspsConfigIpvxAuthMgrEntry .1.3.6.1.4.1.4329.20.1.1.1.1.1.7.10.1 |
snMspsConfigIpvxAuthMgrAddrTypeThe IP address type of SnMspsConfigIpvxAuthMgrEntry.
This value determines the type for
snMspsConfigIpvxAuthMgrAddr and snMspsConfigIpvxAuthMgrAddrLen.
ipv4(1) and ipv6(2) are the only two values supported
in this MIB module. InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.4329.20.1.1.1.1.1.7.10.1.1 |
snMspsConfigIpvxAuthMgrAddrSpecifies either the Network or Host address from which the switch
can be managed.
An address 0.0.0.0 or :: indicates 'Any Manager'. InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.4329.20.1.1.1.1.1.7.10.1.2 |
snMspsConfigIpvxAuthMgrAddrLenIndicates the number of leading one bits that form the
mask to be logical-ANDed with the snMspsConfigIpvxAuthMgrAddr
before being compared to the value in the
snMspsConfigIpvxAuthMgrAddr field.
The values for the index objects snMspsConfigIpvxAuthMgrAddr and
snMspsConfigIpvxAuthMgrAddrLen must be consistent.
Value 0 indicates mask for 'Any Manager'. InetAddressPrefixLength (INET-ADDRESS-MIB) .1.3.6.1.4.1.4329.20.1.1.1.1.1.7.10.1.3 |
snMspsConfigIpvxAuthMgrPortListSpecifies the port numbers through which the authorized manager can
access the switch.
By default the authorized manager is allowed to access the switch
through all the ports.
If a set of ports are configured in the 'PortList', the manager can
access the switch only through the configured ports.rw PortList (Q-BRIDGE-MIB) .1.3.6.1.4.1.4329.20.1.1.1.1.1.7.10.1.4 |
snMspsConfigIpvxAuthMgrVlanListSpecifies the Vlan's in which the IP authorized manager can reside.
By default the manager is allowed to reside in any vlan.
If a set of vlans are configured in the 'VlanList', the manager can
reside only in the configured vlan set. Access to the switch
will be denied from any other vlan.rw OCTET STRING .1.3.6.1.4.1.4329.20.1.1.1.1.1.7.10.1.5 |
snMspsConfigIpvxAuthMgrOOBPortSpecifies whether the authorized manager can access the switch
through OOB Port
By default the manager is denied access to reside on OOB Interfacerw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4329.20.1.1.1.1.1.7.10.1.6 |
snMspsConfigIpvxAuthMgrAllowedServicesSpecifies the allowed services through which the authorized manager can
access the switch.
This object takes bit mask values. The services represented by each bit
position is as given below:
With bit 0 being the Least Significant Bit,
Bit0
Bit1
Bit2
Bit3
Bit4
If the particular bit is set to 1,corresponding service is allowed for
the configured manager.
By default all services are allowed for the configured manager.rw Integer32 .1.3.6.1.4.1.4329.20.1.1.1.1.1.7.10.1.7 |
snMspsConfigIpvxAuthMgrCreationOrderSpecifies creation order of the rulesrw Integer32 .1.3.6.1.4.1.4329.20.1.1.1.1.1.7.10.1.8 |
snMspsConfigIpvxAuthMgrRowStatusThis object indicates the status of this entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.4329.20.1.1.1.1.1.7.10.1.9 |
snMspsConfigIpVlanIdInband ports VLAN ID (VID) from 1 to 4094 or 0 if
the VID is unassigned for the agent.rw INTEGER .1.3.6.1.4.1.4329.20.1.1.1.1.1.8 |
snMspsConfigAgentReceiveOnAllKnownVLANsSetting AgentReceiveOnAllKnownVLANs to Enable(1)
enables the reception of IP traffic for the agent on all VLANs.
This means the agent accepts incoming connections on all the VLANs.
For outgoing traffic like sending SNMP traps and
connection to the e-mail server the Agent VLAN is used.rw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.1.9 |
snMspsConfigVlan0AwareThe VLAN ID of VLAN which is to be in transparent mode. Zero (0) indicates that no VLAN is in transparent mode.rw INTEGER .1.3.6.1.4.1.4329.20.1.1.1.1.1.10 |
snMspsConfigPortCtrlConfigurationTableA table to control the port specific parameters of the device like speed,
duplex mode, etc. SEQUENCE OF SnMspsConfigPortCtrlConfigurationEntry .1.3.6.1.4.1.4329.20.1.1.1.1.1.12 |
snMspsConfigPortCtrlConfigurationEntryAn entry appears in this table for each interface in the system.
Index to the table is the interface index of the port. SnMspsConfigPortCtrlConfigurationEntry .1.3.6.1.4.1.4329.20.1.1.1.1.1.12.1 |
snMspsConfigPortCtrlConfigurationIndexInterface index of the port for which the configuration
in this entry applies. Integer32 .1.3.6.1.4.1.4329.20.1.1.1.1.1.12.1.1 |
snMspsConfigPortCtrlConfigurationModeSpeficies the mode in which the speed, duplex modes and flow control
of the interface is determined.
If set as 'auto', the hardware senses speed and negotiates with the port
on the other end of the link for data transfer operation as
'full-duplex' or 'half-duplex' and about flow contol.
If set as 'nonegotiation', the configured values for interface
speed, duplex mode and flow control will be effective.
The current value of this MIB object represents only configuration state.
The real state of this port-specific parameter may be different ('see snMspsConfigPortCtrlMode').rw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.1.12.1.2 |
snMspsConfigPortCtrlConfigurationDuplexConfigures interface data transfer mode as full-duplex or half-duplex.
This object can be configured only if the 'PortCtrlMode' is 'nonegotiation'.
If the 'PortCtrlMode' is 'auto', it obtains the value from Hardware
after negotiating with its peer.
The current value of this MIB object represents only configuration state.
The real state of this port-specific parameter may be different ('see snMspsConfigPortCtrlDuplex').rw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.1.12.1.3 |
snMspsConfigPortCtrlConfigurationSpeedConfigures interface speed.
This object can be configured only if the 'PortCtrlMode' is 'nonegotiation'.
If the 'PortCtrlMode' is 'auto', it obtains the value from Hardware
after negotiating with its peer.
The current value of this MIB object represents only configuration state.
The real state of this port-specific parameter may be different ('see snMspsConfigPortCtrlSpeed').rw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.1.12.1.4 |
snMspsConfigPortCtrlConfigurationFlowControlEnables / disables flow control for the interface.
This object be configured only if the 'PortCtrlMode' is 'nonegotiation'.
If the 'PortCtrlMode' is 'auto', it obtains the value from Hardware
after negotiating with its peer.
The current value of this MIB object represents only configuration state.
The real state of this port-specific parameter may be different ('see snMspsConfigPortCtrlFlowControl').rw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.1.12.1.5 |
snMspsConfigPortCtrlConfigurationRenegotiateWhen configured as 'true', restarts autonegotiation on the interface.
Once autonegotiation is restarted, the value of this object reverts
to 'false'.
The current value of this MIB object represents only configuration state.
The real state of this port-specific parameter may be different ('see snMspsConfigPortCtrlRenegotiate').rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4329.20.1.1.1.1.1.12.1.6 |
snMspsConfigPortCtrlConfigurationMaxMacAddrSpecifies the maximum number of new MAC addresses that can be
learnt over the interface.
The current value of this MIB object represents only configuration state.
The real state of this port-specific parameter may be different ('see snMspsConfigPortCtrlMaxMacAddr').rw Integer32 .1.3.6.1.4.1.4329.20.1.1.1.1.1.12.1.7 |
snMspsConfigPortCtrlConfigurationMaxMacActionSpecifies the action to be taken when the maximum number of new MAC
addresses that can be learnt over the interface is exceeded.
If the action is 'drop', the packet with new mac address will be
dropped once the maximum number of new MAC addresses that can be
learnt over the interface is exceeded.
If the action is 'purgeLRU', the 'Least Recently Used' mac address
will be deleted from the MAC table and the new mac address will be
added.
The current value of this MIB object represents only configuration state.
The real state of this port-specific parameter may be different ('see snMspsConfigPortCtrlMaxMacAction').rw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.1.12.1.8 |
snMspsConfigPortCtrlConfigurationHOLBlockPreventionEnables or disables Head-Of-Line Blocking prevention on a port.
The current value of this MIB object represents only configuration state.
The real state of this port-specific parameter may be different ('see snMspsConfigPortHOLBlockPrevention').rw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.1.12.1.9 |
snMspsConfigRateCtrlLimitTableA table to control the rate limiting parameters
either for the entire switch or for each physical and port-channel
interface in the switch. SEQUENCE OF SnMspsConfigRateCtrlLimitEntry .1.3.6.1.4.1.4329.20.1.1.1.1.1.15 |
snMspsConfigRateCtrlLimitEntryAn entry appears in this table for each physical and port-channel
interface in the switch. SnMspsConfigRateCtrlLimitEntry .1.3.6.1.4.1.4329.20.1.1.1.1.1.15.1 |
snMspsConfigRateCtrlLimitIndexThe interface index for which the configuration in this
entry applies. Integer32 .1.3.6.1.4.1.4329.20.1.1.1.1.1.15.1.1 |
snMspsConfigRateCtrlLimitValueAllows to configure the limiting value for the maximum number
of dlf, multicast and broadcast data that can be transmitted
per second over this interface. The unit of data is given by
snMspsConfigRateCtrlUnit object. Setting this object to the
value zero disables rate limiting for Destination lookup failure
packets on this interface. The value that can be set for this
object is limited by the underlying hardwarerw Integer32 .1.3.6.1.4.1.4329.20.1.1.1.1.1.15.1.2 |
snMspsConfigRateCtrlUnitDefines unit of rate limiting values in corresponding entry
from snMspsConfigRateCtrlTable. It can be treated
either in packet per second or kilobit per second.ro Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.1.16 |
snMspsConfigSwitchAgingEnableEnable/Disable auto-aging functionality of the learning table.rw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.1.20 |
snMspsConfigSwitchSnifferBarrierEnableEnable/Disable Monitor Barrier functionality. If disabled the mirror destination
port is also part of the switching enginerw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.1.25 |
snMspsConfigSwitchTimeShow/Set -MM/DD/YYYY hh:mm:ss- date and time of the switch.rw DisplayString .1.3.6.1.4.1.4329.20.1.1.1.1.1.27 |
snMspsConfigurationSaveModeWhen set to 'autosave(2)', all nonvolatile configuration parameters
are saved automaticly to flash after configuration changes. In 'trailmode (1)' save
must be triggered manually. Autosave mode may not be available on all devices.
In this case, 'wrong value' error will be returned, when trying to set 'autosave(2)'rw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.1.28 |
snMspsInitiateConfigSaveWhen set as 'true' switch configurations save operation is
initiated.
As soon as the configuration save operation is completed, the value
of this object reverts back to 'false'.
All the configurations made via the three interfaces
viz.
-> commandline interface
-> Web Interface
-> SNMP interface
are saved either in 'Startup Configuration File' in the flash or
in the specified 'issConfigSaveFileName' in the flash or
in the chosen remote system, depending upon 'ConfigSaveOption'.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4329.20.1.1.1.1.1.29 |
snMspsConfigLastSynchronisationTimeMM/DD/YYYY hh:mm:ss- This is the time when the system time is last synchronized.
It return zero length value if the system time is not yet synchronized.ro DisplayString .1.3.6.1.4.1.4329.20.1.1.1.1.1.30 |
snMspsConfigChangesSavedValue 'true' means there are no configuration changes that are not saved.
Otherwise it will have the value 'false'.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4329.20.1.1.1.1.1.31 |
snMspsConfigurationAutoRestartTimerWhen setting to time interval in seconds, device will perform restart
automatically after the time interval is expired.
Setting 0 will cancel any timer, which was previously setrw INTEGER (0|300..86400) .1.3.6.1.4.1.4329.20.1.1.1.1.1.32 |
snMspsEnhancedPassiveListeningCompatibilityEnables or disables Enhance Passive Listening Compatibility mode on this device.
If port wise configuration is supported, the port specific object
<snMspsPortEnhPassListComp> must be configured for each port in order to support the feature.rw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.1.35 |
snMspsConfigVrrpAcceptPingEnable/disable ability to accept pings to associated ip addressesrw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.1.41 |
snMspsOperLoginPasswordPolicyShows the password policy which is enforced to users when determining their password.
Low - password should contain minimum 6 characters,
Medium - not supported,
High - password should contain minimum 8 characters, minimum 1 upper case character,
minimum 1 special character, and minimum 1 number.ro Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.1.60 |
snMspsConfigLoginPasswordPolicySets the password policy which is enforced to users when determining their password.
Low - password should contain minimum 6 characters,
Medium - not supported,
High - password should contain minimum 8 characters, minimum 1 upper case character,
minimum 1 special character, and minimum 1 number.rw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.1.61 |
snMspsLoginUsers OBJECT IDENTIFIER .1.3.6.1.4.1.4329.20.1.1.1.1.1.65 |
snMspsLoginUsersTableThis table contains the login usernames and privileges, which are currently created. SEQUENCE OF SnMspsLoginUsersTableEntry .1.3.6.1.4.1.4329.20.1.1.1.1.1.65.5 |
snMspsLoginUsersTableEntryuser table entry SnMspsLoginUsersTableEntry .1.3.6.1.4.1.4329.20.1.1.1.1.1.65.5.1 |
snMspsLoginUserNameUser Name which is used as index of the snMspsLoginUserTable. DisplayString .1.3.6.1.4.1.4329.20.1.1.1.1.1.65.5.1.1 |
snMspsLoginUserPrivilegeUser Privilegero Integer32 .1.3.6.1.4.1.4329.20.1.1.1.1.1.65.5.1.2 |
snMspsLoginUserRemoteAccessRemote Access Filter . Value 0 means its allowed to access.ro Integer32 .1.3.6.1.4.1.4329.20.1.1.1.1.1.65.5.1.3 |
snMspsConfigBackup OBJECT IDENTIFIER .1.3.6.1.4.1.4329.20.1.1.1.1.1.100 |
snMspsConfigBackupTableA table to display and to control the configuration pack backup. SEQUENCE OF SnMspsConfigBackupEntry .1.3.6.1.4.1.4329.20.1.1.1.1.1.100.10 |
snMspsConfigBackupEntryAn entry appears in this table for each configuration pack. SnMspsConfigBackupEntry .1.3.6.1.4.1.4329.20.1.1.1.1.1.100.10.1 |
snMspsConfigBackupIndexThe auxiliary number of corresponding entry
representing settings of each config backup. Integer32 .1.3.6.1.4.1.4329.20.1.1.1.1.1.100.10.1.1 |
snMspsConfigBackupFileNameThe file name of configuration backup.rw DisplayString .1.3.6.1.4.1.4329.20.1.1.1.1.1.100.10.1.4 |
snMspsConfigBackupFileSizeThe file size in kilobytes of configuration backup.ro Integer32 .1.3.6.1.4.1.4329.20.1.1.1.1.1.100.10.1.7 |
snMspsConfigBackupOperationThis is a trigger and status variable.
Write access using restore(1), initiates restore of corresponding backup
configuration. After the operation is completed, the object will return idle(0).
Write access using other values as restore(1) will cause 'bad value' error.
Read access will return following values:
0 - No action in performing or last action was successfull.
2 - Last initiated action (restore or create new backup) is in progress.
3 - No enough free memory to create new configuration backup.
4 - Internal error during last action.rw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.1.100.10.1.50 |
snMspsConfigBackupStatusThis is a control variable.
It controls the instantiation of a conceptual row
in snMspsConfigBackupTable.
The new row cannot be activated as long as
snMspsConfigBackupFileName is not set.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.4329.20.1.1.1.1.1.100.10.1.100 |
snMspsConfigSourceIpVlanIdConfigures the LoopBack IP interface VLAN ID (1 to 4094).
Non-Zero IPv4/IPv6 Address of this LoopBack interface will be
used as Source Address for management communication.
Using of Loopback IP as source IP is applicable for Syslog,
SMTP, NTP, SNTP, Radius and SNMP Packets generated from this
device.
If snMspsConfigSourceIpVlanId is 0, then this feature
is disabled.
If snMspsConfigSourceIpVlanId in non-zero,
and if the corresponding Loopback interface has IPv4 Address as
0.0.0.0, then this feature is disabled for all IPv4 management
communication.
If the loopback interface does not have an
active IPv6 Global Address, then this feature is disabled for
all IPv6 management communication.rw INTEGER .1.3.6.1.4.1.4329.20.1.1.1.1.1.101 |
snMspsConfigNetworkFilteringEnable/disable ability to identify and temporarily filter source mac-addresses of the incoming network traffic that cause CPU congestion.
Traffic from identified source mac-addresses will not be switched for the filter period.rw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.1.201 |
snMspsGeneral OBJECT IDENTIFIER .1.3.6.1.4.1.4329.20.1.1.1.1.2 |
snMspsGeneralDeviceTypeDevice Type of current product. This value is the part of
fully-qualified domain name, which is stored in sys-Name.ro DisplayString .1.3.6.1.4.1.4329.20.1.1.1.1.2.5 |
snMspsGeneralDeviceGroupThe group name of the device, which is used as a part
of the cplug device's identification dataro DisplayString .1.3.6.1.4.1.4329.20.1.1.1.1.2.10 |
snMspsGeneralHwVersionTableThis table contains version informations of all hardware
(basic device and extension cards), which are currently
available on the device. SEQUENCE OF SnMspsGeneralHwVersionEntry .1.3.6.1.4.1.4329.20.1.1.1.1.2.20 |
snMspsGeneralHwVersionEntryAn entry appears in this table for each hardware
in the system, which has a MLFB number. SnMspsGeneralHwVersionEntry .1.3.6.1.4.1.4329.20.1.1.1.1.2.20.1 |
snMspsGeneralHwVersionTableIndexThis index correlates with entPhysicalIndex
from entPhysicalTable (ENTITY-MIB). INTEGER .1.3.6.1.4.1.4329.20.1.1.1.1.2.20.1.1 |
snMspsGeneralHwTypeThe type of hardware in readable format.ro DisplayString .1.3.6.1.4.1.4329.20.1.1.1.1.2.20.1.2 |
snMspsGeneralHwNameThe name of hardware in readable format.ro DisplayString .1.3.6.1.4.1.4329.20.1.1.1.1.2.20.1.3 |
snMspsGeneralHwRevisionThe number of hardware revision.ro DisplayString .1.3.6.1.4.1.4329.20.1.1.1.1.2.20.1.4 |
snMspsGeneralHwOrderIdOrder ID of hardware.ro SnMspsOrderNumber .1.3.6.1.4.1.4329.20.1.1.1.1.2.20.1.5 |
snMspsGeneralSwVersionTableThis table contains version informations of software, which is currently
running on relevant hardware (basic device and extension cards). SEQUENCE OF SnMspsGeneralSwVersionEntry .1.3.6.1.4.1.4329.20.1.1.1.1.2.25 |
snMspsGeneralSwVersionEntryAn entry appears in this table for each software
running in the system. Since the same kinds of software
could run on different hardware, which is available
on the device, the index from 'snMspsGeneralHwVersionTable'
is also used here. SnMspsGeneralSwVersionEntry .1.3.6.1.4.1.4329.20.1.1.1.1.2.25.1 |
snMspsGeneralSwVersionTableIndexThe numerical index of software,
which is available on relevant hardware. INTEGER .1.3.6.1.4.1.4329.20.1.1.1.1.2.25.1.1 |
snMspsGeneralSwTypeThe type of software in readable format.ro DisplayString .1.3.6.1.4.1.4329.20.1.1.1.1.2.25.1.2 |
snMspsGeneralSwRevisionThe number of software revision.ro SnMspsVersionNumber .1.3.6.1.4.1.4329.20.1.1.1.1.2.25.1.3 |
snMspsGeneralSwDateThe revision date of software.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.4329.20.1.1.1.1.2.25.1.4 |
snMspsGeneralSwDescriptionThe description of software.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.4329.20.1.1.1.1.2.25.1.5 |
snMspsVlan OBJECT IDENTIFIER .1.3.6.1.4.1.4329.20.1.1.1.1.3 |
snMspsSnmp OBJECT IDENTIFIER .1.3.6.1.4.1.4329.20.1.1.1.1.4 |
snMspsLa OBJECT IDENTIFIER .1.3.6.1.4.1.4329.20.1.1.1.1.5 |
snMspsMstp OBJECT IDENTIFIER .1.3.6.1.4.1.4329.20.1.1.1.1.6 |
snMspsSnooping OBJECT IDENTIFIER .1.3.6.1.4.1.4329.20.1.1.1.1.9 |
snMspsPnac OBJECT IDENTIFIER .1.3.6.1.4.1.4329.20.1.1.1.1.10 |
snMspsRadius OBJECT IDENTIFIER .1.3.6.1.4.1.4329.20.1.1.1.1.11 |
snMspsRadiusServer OBJECT IDENTIFIER .1.3.6.1.4.1.4329.20.1.1.1.1.11.2 |
snMspsRmon OBJECT IDENTIFIER .1.3.6.1.4.1.4329.20.1.1.1.1.12 |
snMspsIp OBJECT IDENTIFIER .1.3.6.1.4.1.4329.20.1.1.1.1.13 |
snMspsDhcp OBJECT IDENTIFIER .1.3.6.1.4.1.4329.20.1.1.1.1.17 |
snMspsDhcpClient OBJECT IDENTIFIER .1.3.6.1.4.1.4329.20.1.1.1.1.17.1 |
snMspsDhcpClientControlThe value enabled(1) will run DHCP Client.
The value disabled(2) will inhibit DHCP.rw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.17.1.1 |
snMspsDhcpClientModeThe value enabled-via-mac-address(1)
sets DHCP Client Mode with option
MAC Address as ClientId,
enabled-via-client-id(2) runs DHCP Client Mode
with option ClientId,
enabled-via-sysname(3) runs DHCP Client with
the sysname as ClientId,
enabled-via-nameofstation(4) runs DHCP with
the name of station as ClientId,
enabled-via-iaidandduid(5) runs DHCP with RFC 3315 style
identifier binding as client identifier. DUID type is
determined by snMspsDhcpClientIfDuidType object.rw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.17.1.2 |
snMspsDhcpClientConfigFileRequestIf enabled(1) DHCP client requests option 66/67 .rw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.17.1.3 |
snMspsDhcpClientIdAn administratively-assigned name
for this DHCP client.rw DisplayString .1.3.6.1.4.1.4329.20.1.1.1.1.17.1.4 |
snMspsDhcpClientIPAddrKeepAliveIf enabled (1) DHCP client will retain the ip address from server
accordingly to MSPS requirements.
If disabled(2) DHCP client reset the ip address to 0.0.0.0
accordingly to RFC.rw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.17.1.5 |
snMspsDhcpClientDUID OBJECT IDENTIFIER .1.3.6.1.4.1.4329.20.1.1.1.1.17.1.10 |
snMspsDhcpClientDuidTypeThis Object contains the type of DUID. Client sends the Client Identifier
TLV in the client sending messages.
The value dtLlt(1) indicates that DHCP client will use the Link layer address
of the interface and Current System time value for the Client Identifier
option TLV value.
The value dtEn (2) indicates that DHCP client will use the Vendor-assigned
unique ID based on Enterprise Number for the Client Identifier
option TLV value.
The value dtLl (3) indicates that DHCP client will use the link layer address
for the client Identifier option TLV value.rw SnMspsDhcpClientDuidType .1.3.6.1.4.1.4329.20.1.1.1.1.17.1.10.1 |
snMspsDhcpClientDuidLltValueThis Object contains the value of Link-layer Address plus Time DUID. This DUID value is used by client if dtLlt is selected in snMspsDhcpClientDuidType.ro SnMspsDhcpClientDuidValue .1.3.6.1.4.1.4329.20.1.1.1.1.17.1.10.2 |
snMspsDhcpClientDuidEnValueThis object contains the value of vendor-assigned unique ID based on Enterprise Number DUID. This DUID value is used by client if dtEn is selected in snMspsDhcpClientDuidType.ro SnMspsDhcpClientDuidValue .1.3.6.1.4.1.4329.20.1.1.1.1.17.1.10.3 |
snMspsDhcpClientDuidLlValueThis Object contains the value of Link-layer address DUID. This DUID value is used by client if dtLl is selected in snMspsDhcpClientDuidType.ro SnMspsDhcpClientDuidValue .1.3.6.1.4.1.4329.20.1.1.1.1.17.1.10.4 |
snMspsDhcpServer OBJECT IDENTIFIER .1.3.6.1.4.1.4329.20.1.1.1.1.17.2 |
snMspsDhcpRelay OBJECT IDENTIFIER .1.3.6.1.4.1.4329.20.1.1.1.1.17.3 |
snMspsSntp OBJECT IDENTIFIER .1.3.6.1.4.1.4329.20.1.1.1.1.19 |
snMspsSntpClient OBJECT IDENTIFIER .1.3.6.1.4.1.4329.20.1.1.1.1.19.1 |
snMspsHttp OBJECT IDENTIFIER .1.3.6.1.4.1.4329.20.1.1.1.1.20 |
snMspsHttpRedirectionStatusThe status of the HTTP redirectionrw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.20.1 |
snMspsHttpToHttpsRedirectionStatusThe status of the HTTP to HTTPS redirection.
If device do not support this feature, the value of this MIB object
can not be set to true.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4329.20.1.1.1.1.20.2 |
snMspsHttpRedirectionTableThe (conceptual) table listing the Redirection related objects SEQUENCE OF SnMspsHttpRedirectionEntry .1.3.6.1.4.1.4329.20.1.1.1.1.20.4 |
snMspsHttpRedirectionEntryAn entry (conceptual row) in the snMspsHttpRedirectionTable. SnMspsHttpRedirectionEntry .1.3.6.1.4.1.4329.20.1.1.1.1.20.4.1 |
snMspsHttpRedirectionURLThe URL which has to be redirected DisplayString .1.3.6.1.4.1.4329.20.1.1.1.1.20.4.1.1 |
snMspsHttpRedirectedSrvAddrTypeThe Address type of HTTP server to which URL has to be
redirectedrw InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.4329.20.1.1.1.1.20.4.1.2 |
snMspsHttpRedirectedSrvIPThe IP address of the HTTP Server to which redirect has to be done
interface belongs torw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.4329.20.1.1.1.1.20.4.1.3 |
snMspsHttpRedirectedSrvDomainNameThe domain name of the HTTP server to which the URL has to be
has to redirectedrw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.4329.20.1.1.1.1.20.4.1.4 |
snMspsHttpRedirectionEntryStatusThe status of HTTP redirection table entryrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.4329.20.1.1.1.1.20.4.1.5 |
snMspsWBMTimeOutTime out for the Web-Based-Management in seconds. Range 60s to 3600s.
If value is 0, timeout is disabled.rw INTEGER .1.3.6.1.4.1.4329.20.1.1.1.1.20.7 |
snMspsWBMDefaultLoginPageDefault login page for the Web-Based-Management.rw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.20.8 |
snMspsHttpPortThe port to be used by the hosts/PC to configure the device using the Web Interface
Allowed values are default port and ports in the dynamic port range (49500-65535).
Get operation return current listening port.
The HTTP server must be disabled before this configuration is done
Set operation return Inconsistent value for any one of the following
1. if the set port value is other than allowed port range or
2. if the port already used by another service in the device or
3. if the device does not support to change the port.rw Integer32 .1.3.6.1.4.1.4329.20.1.1.1.1.20.10 |
snMspsHttpStatusThis object is for enabling or disabling HTTP in the system.rw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.20.11 |
snMspsHttpSslSecureHttpMinTlsVersionThis object holds the configuration of the minimum Tls Version for secure HTTP in the system.rw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.20.15 |
snMspsHttpSslSecureHttpStatusThis object is for enabling or disabling secure HTTP in the system.rw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.20.16 |
snMspsHttpSslPortThis object is to configure the SSL port.
Allowed values are default port and ports in the dynamic port range (49500-65535).
Get operation return current listening port.
The HTTP Secure server must be disabled before this configuration is done
Set operation return Inconsistent value for any one of the following
1. if the set port value is other than allowed port range or
2. if the port already used by another service in the device or
3. if the device does not support to change the port.rw Integer32 .1.3.6.1.4.1.4329.20.1.1.1.1.20.17 |
snMspsHttpSshStatusThis object is for enabling or disabling ssh in the system.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4329.20.1.1.1.1.20.18 |
snMspsHttpSshPortSSh service's server listening port.
Allowed values are default port and ports in the dynamic port range (49500-65535).
Get operation return current listening port.
The SSH server must be disabled before this configuration is done
Set operation return Inconsistent value for any one of the following
1. if the set port value is other than allowed port range or
2. if the port already used by another service in the device or
3. if the device does not support to change the port.rw Integer32 .1.3.6.1.4.1.4329.20.1.1.1.1.20.19 |
snMspsHttpTelnetPortTelnet service's server listening port.
Allowed values are default port and ports in the dynamic port range (49500-65535).
Get operation return current listening port.
The Telnet server must be disabled before this configuration is done
Set operation return Inconsistent value for any one of the following
1. if the set port value is other than allowed port range or
2. if the port already used by another service in the device or
3. if the device does not support to change the port.rw Integer32 .1.3.6.1.4.1.4329.20.1.1.1.1.20.23 |
snMspsSyslog OBJECT IDENTIFIER .1.3.6.1.4.1.4329.20.1.1.1.1.21 |
snMspsSyslogClient OBJECT IDENTIFIER .1.3.6.1.4.1.4329.20.1.1.1.1.21.1 |
snMspsQos OBJECT IDENTIFIER .1.3.6.1.4.1.4329.20.1.1.1.1.22 |
snMspsQosCos OBJECT IDENTIFIER .1.3.6.1.4.1.4329.20.1.1.1.1.22.3 |
snMspsQosDscp OBJECT IDENTIFIER .1.3.6.1.4.1.4329.20.1.1.1.1.22.4 |
snMspsQosSchedule OBJECT IDENTIFIER .1.3.6.1.4.1.4329.20.1.1.1.1.22.10 |
snMspsQosCosPort OBJECT IDENTIFIER .1.3.6.1.4.1.4329.20.1.1.1.1.22.12 |
snMspsQosBcast OBJECT IDENTIFIER .1.3.6.1.4.1.4329.20.1.1.1.1.22.14 |
snMspsQosAgentMac OBJECT IDENTIFIER .1.3.6.1.4.1.4329.20.1.1.1.1.22.16 |
snMspsCplug OBJECT IDENTIFIER .1.3.6.1.4.1.4329.20.1.1.1.1.23 |
snMspsRedundancy OBJECT IDENTIFIER .1.3.6.1.4.1.4329.20.1.1.1.1.24 |
snMspsRingRedundancy OBJECT IDENTIFIER .1.3.6.1.4.1.4329.20.1.1.1.1.24.1 |
snMspsRingRedundancyModeRedundancy Mode:
ringRedundancyOff(1) - no redundancy
ringRedundancyHrpOn(2) - high speed redundancy protocol
ringRedundancyMrpOn(3) - media redundancy protocol
ringRedundancyArd(4) - automatic redundancy detection.rw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.24.1.1 |
snMspsHrpRmModeHRP RM mode.rw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.24.1.2 |
snMspsRmStateRM State.ro Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.24.1.3 |
snMspsRmStateChangesNumber of changes to RM active state.ro Counter32 .1.3.6.1.4.1.4329.20.1.1.1.1.24.1.4 |
snMspsStaticPortPortnumber of static port (HRP) or RingPort 2 (MRP).rw INTEGER .1.3.6.1.4.1.4329.20.1.1.1.1.24.1.5 |
snMspsIsolatedPortPortnumber of isolated port (HRP) or RingPort 1 (MRP).rw INTEGER .1.3.6.1.4.1.4329.20.1.1.1.1.24.1.6 |
snMspsTestMaxDelayMeasured maximum delay of RM test telegrams.ro INTEGER .1.3.6.1.4.1.4329.20.1.1.1.1.24.1.7 |
snMspsRmResetCountersReset all counters of Redundancy protocol software. At the moment only supported for HRP.rw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.24.1.8 |
snMspsMrpRmModeMRP RM mode.
rmOff(1) - ring client
rmOn(2) - ring manager (MRP AUTO manager if ringRedundancyMrpOn)
rmNormOn(3) - ring norm manager (MRP NORM manager if ringRedundancyMrpOn)rw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.24.1.9 |
snMspsRingRedundancyOperStateRing Redundancy Oper State:
disabled(1) - no redundancy
hrpClient(2) - high speed redundancy protocol client
hrpManager(3) - high speed redundancy protocol manager
mrpClient(4) - media redundancy protocol client
mrpManager(5) - media redundancy protocol manager.ro Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.24.1.10 |
snMspsHrpRedundancyLostFaultLEDEnables or disables the Fault LED when Ring Redundancy (HRP and MRP) is lost (Redundancy Manager or Standby).rw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.24.1.11 |
snMspsMrpDomainNameMedia redundancy protocol domain name.ro DisplayString .1.3.6.1.4.1.4329.20.1.1.1.1.24.1.16 |
snMspsMrpRestoreDefaultConfigRestore default ring redundancy configuration.rw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.24.1.20 |
snMspsMultiMrpTableTable containing MRP multi-ring configuration. SEQUENCE OF SnMspsMultiMrpEntry .1.3.6.1.4.1.4329.20.1.1.1.1.24.1.30 |
snMspsMultiMrpEntryInterface entry containing objects for MRP multi-ring configuration. SnMspsMultiMrpEntry .1.3.6.1.4.1.4329.20.1.1.1.1.24.1.30.1 |
snMspsMultiMrpIndexUnique number for each MRP ring. The number for each MRP ring must remain
constant at least from one re-initialization of the entity's
network management system to the next re-initialization. INTEGER .1.3.6.1.4.1.4329.20.1.1.1.1.24.1.30.1.1 |
snMspsMultiMrpDomainNameInstance MRP domain name.rw DisplayString .1.3.6.1.4.1.4329.20.1.1.1.1.24.1.30.1.3 |
snMspsMultiMrpAdminModeringRedundancyOff(1) - no redundancy
ringRedundancyHrpOn(2) - high speed redundancy protocol
ringRedundancyMrpOn(3) - media redundancy protocol
ringRedundancyArd(4) - automatic redundancy detection.rw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.24.1.30.1.9 |
snMspsMultiMrpAdminRolermOff(1) - ring client
rmOn(2) - ring manager (MRP AUTO manager if ringRedundancyMrpOn)
rmNormOn(3) - ring norm manager (MRP NORM manager if ringRedundancyMrpOn)rw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.24.1.30.1.12 |
snMspsMultiHrpAdminRolermOff(1) - HRP ring client
rmOn(2) - HRP ring managerrw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.24.1.30.1.14 |
snMspsMultiMrpAdminRingPort1Configured Portnumber of first ring-port.rw INTEGER .1.3.6.1.4.1.4329.20.1.1.1.1.24.1.30.1.16 |
snMspsMultiMrpAdminRingPort2Configured Portnumber of second ring-port.rw INTEGER .1.3.6.1.4.1.4329.20.1.1.1.1.24.1.30.1.19 |
snMspsMultiMrpOperStatedisabled(1) - no redundancy
hrpClient(2) - high speed redundancy protocol client
hrpManager(3) - high speed redundancy protocol manager
mrpClient(4) - media redundancy protocol client
mrpManager(5) - media redundancy protocol auto manager
mrpNormManager(6) - media redundancy protocol norm managerro Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.24.1.30.1.21 |
snMspsMultiRmStateCurrent Redundancy Manager's active/passive state.ro Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.24.1.30.1.23 |
snMspsMultiMrpOperRingPort1Current first ring-port's portnumber.ro INTEGER .1.3.6.1.4.1.4329.20.1.1.1.1.24.1.30.1.25 |
snMspsMultiMrpOperRingPort2Current second ring-port's portnumber.ro INTEGER .1.3.6.1.4.1.4329.20.1.1.1.1.24.1.30.1.28 |
snMspsMultiMrpRmStateChangesNumber of changes to RM active state.ro Counter32 .1.3.6.1.4.1.4329.20.1.1.1.1.24.1.30.1.31 |
snMspsMultiMrpTestMaxDelayMeasured maximum delay of RM test telegrams.ro INTEGER .1.3.6.1.4.1.4329.20.1.1.1.1.24.1.30.1.36 |
snMspsMultiMrpStatusThe status of the aggregation row.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.4329.20.1.1.1.1.24.1.30.1.40 |
snMspsRingRedundancyStandby OBJECT IDENTIFIER .1.3.6.1.4.1.4329.20.1.1.1.1.24.2 |
snMspsStandbyModeStandby connection mode.rw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.24.2.1 |
snMspsStandbyConnectionNameThe standby connection name (Max 32 Symbol).rw DisplayString .1.3.6.1.4.1.4329.20.1.1.1.1.24.2.3 |
snMspsStandbyStateStandby connection state.
Bit 0 is always 1, bit 1 is Master/Slave,
bit 2 is Active/Passive and bit 8 is Partner not found or not.
standbyMasterPassive(1) - Master in passive state
standbySlavePassive(3) - Slave in passive state
standbyMasterActive(5) - Master in active state
standbySlaveActive(7) - Slave in passive state
standbyMasterPassive-lost(17) - Master in passive state but partner is lost
standbySlavePassive-lost(19) - Slave in passive state but partner is lost
standbyMasterActive-lost(21) - Master in active state but partner is lost
standbySlaveActive-lost(23) - Slave in active state but partner is lost
standbyWaitingForPartner(257) - Waiting for partner, partner was not yet found
standbyDisabled(300) - Standby connection is disabledro Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.24.2.4 |
snMspsStandbyStateChangesNumber of changes to Standby connection active state.ro Counter32 .1.3.6.1.4.1.4329.20.1.1.1.1.24.2.5 |
snMspsStandbyResetCountersReset all counters of Standby protocol software.rw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.24.2.6 |
snMspsStandbyForceToMasterForce this device to Standby master.rw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.24.2.7 |
snMspsStandbyStartDelayTime in [ms] that a standby master/slave will wait
before to enable its standby ports even if no standby
partner has been contacted yet.
If set to zero (default) master/slave do not enable
any standby port until being connected with the
partner standby slave/masterrw INTEGER .1.3.6.1.4.1.4329.20.1.1.1.1.24.2.12 |
snMspsStandbyBackoffcontrols Standby device backoff mechanisms.rw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.24.2.14 |
snMspsRingRedundancyObserver OBJECT IDENTIFIER .1.3.6.1.4.1.4329.20.1.1.1.1.24.3 |
snMspsRmObserverModeRM Observer Mode.rw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.24.3.1 |
snMspsRmObserverStateRM Observer State.ro Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.24.3.2 |
snMspsRedundancyExt OBJECT IDENTIFIER .1.3.6.1.4.1.4329.20.1.1.1.1.24.4 |
snMspsPassiveListeningEnableEnable / Disable Passive Listening Functionality.
On enabled the device reacts on receiving a TCN (Topology Change Notifications) even (and only) if (R)STP is disabled.rw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.24.4.1 |
snMspsPassiveListeningBpduVlanFwdEnable / Disable Forwarding of BPDU in VLAN member ports when Passive Listening Functionality is enabled.
On enabled the device forwards the BPDU only on the VLAN member ports.
On disabled the device forwards on all the available ports in the system.rw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.24.4.2 |
snMspsRingRedundancyMrpIntercon OBJECT IDENTIFIER .1.3.6.1.4.1.4329.20.1.1.1.1.24.5 |
snMspsMrpInterconStatusMRP Interconnection protocol status.
If set to disabled(2), all configured entries of the MRP Interconnection
table are set out of sevice, despite the mode and the admin role.
If set to enabled(1), all configured entries are put into operation,
depending on the mode and the admin role.rw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.24.5.1 |
snMspsMrpInterconResetCountersReset all counters of MRP Interconnection protocol software.
This object is not persistent.rw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.24.5.2 |
snMspsMrpInterconTableEvery entry in this table contains information about
a Media redundancy Interconnection domain. SEQUENCE OF SnMspsMrpInterconEntry .1.3.6.1.4.1.4329.20.1.1.1.1.24.5.10 |
snMspsMrpInterconEntryAn entry in the snMspsMrpInterconTable. SnMspsMrpInterconEntry .1.3.6.1.4.1.4329.20.1.1.1.1.24.5.10.1 |
snMspsMrpInterconIndexThe index of the entry Unsigned32 .1.3.6.1.4.1.4329.20.1.1.1.1.24.5.10.1.1 |
snMspsMrpInterconDomainIDAn identifier of the Media redundancy Interconnection domain
which represents an Interconnection topology.
A value of 0 (invalid) indicates that no ID is given yet.rw Unsigned32 .1.3.6.1.4.1.4329.20.1.1.1.1.24.5.10.1.2 |
snMspsMrpInterconDomainNameA logical name for the Media redundancy Interconnection domain to
ease the management of Media redundancy Interconnection domains.rw DisplayString .1.3.6.1.4.1.4329.20.1.1.1.1.24.5.10.1.3 |
snMspsMrpInterconPortThe ifIndex of the layer 2 interface which is used
as interconnection port.
A value of 0 (invalid) indicates that no interface is selected yet.rw Integer32 .1.3.6.1.4.1.4329.20.1.1.1.1.24.5.10.1.4 |
snMspsMrpInterconPortStateOperational state of the Interconnection port.
disabled(1) indicates that all frames are dropped.
blocked(2) indicates that all frames are dropped except
- MRP Interconnection topology change frames,
- MRP Interconnection test frames,
- MRP Interconnection link change frames,
- MRP Interconnection link status poll frames,
- frames from other protocols that also define to pass
blocked(2) ports.
forwarding(3) indicates that all frames are passed through
according to the forwarding behavior of IEEE 802.1D.
notConnected(4) indicates that the port has no link.ro Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.24.5.10.1.5 |
snMspsMrpInterconModeControl the MRP Interconnection mode.
The value disable(0) is used to set the entry persistent
out of service (the corresponding row status has to be set)
without losing the primary configuration (mainly admin role).
In this case, the MRP Interconnection entity of this domain
shall be disabled as is with admin role disable(0).
The value undefined(1) signals that the interconnection mode is
not disable(0) and neither set to lcMode(2) nor to rcMode(3).
If the value is set to lcMode(2) the devices in Media redundancy
Interconnection Manager (MIM) role as well as these in Media
redundancy Interconnection Client role (MIC) are using the link
check mode to detect open or closed interconnection links.
If the value is set to rcMode(3) the device in Media redundancy
Interconnection Manager (MIM) role is using the ring check mode to
detect open or closed interconnection links.
The factory settings are recommended to adjust the
value of this object to the lcMode(2) capability.
If the agent restricts the write access, no matter what
reason, it shall reject write requests by responding
with 'badValue'.rw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.24.5.10.1.7 |
snMspsMrpInterconAdminRoleControl the MRP Interconnection behavior of the system per
Media redundancy Interconnection domain.
If the value is set to disable(0) the MRP Interconnection
entity of this domain shall be disabled.
If the value is set to client(1) the entity shall be set
to the role of a Media redundancy Interconnection Client (MIC).
If the value is set to manager(2) the entity shall be set
to the role of a Media redundancy Interconnection Manager (MIM).
The factory settings are recommended to adjust the
value of this object to the client(1) capability of the
component in order to prevent multiple managers are
in the interconnection (the order of the capabilities are not
necessarily conform to the order of the object values here).
If the agent restricts the write access, no matter what
reason, it shall reject write requests by responding
with 'badValue'.rw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.24.5.10.1.8 |
snMspsMrpInterconOperRoleThe operational role of an MRP Interconnection entity
per Media redundancy Interconnection domain.
A value of disable(0) signals that the entity doesn't
work (whatever reason).
A value of client(1) signals that the entity is in a
Media redundancy Interconnection Client role.
A value of manager(2) signals that the entity is the
manager of this Media redundancy Interconnection domain.ro Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.24.5.10.1.9 |
snMspsMrpInterconStateOperational status of a MIM of the MRP Interconnection entity.
disable(0) The entity is disabled.
undefined(1) Value is not valid.
interconnOpen(2) MRP Interconnection redundancy lost of this Media
redundancy Interconnection domain.
interconnClosed(3) MRP Interconnection redundancy available of this Media
redundancy Interconnection domain.ro Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.24.5.10.1.10 |
snMspsMrpInterconOpenCountCounter for MRP Interconnection state changes to interconnOpen.ro Counter32 .1.3.6.1.4.1.4329.20.1.1.1.1.24.5.10.1.12 |
snMspsMrpInterconLastOpenChangeTimeticks since last change of snMspsMrpInterconState to interconnOpen.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.4329.20.1.1.1.1.24.5.10.1.13 |
snMspsMrpInterconPeerMACDevice-MAC-Address of the devices interconnection peer, connected
to the devices interlink port.
This variable contains the MAC-Address contained in the media link
check frame received at the interconnection port.ro OCTET STRING .1.3.6.1.4.1.4329.20.1.1.1.1.24.5.10.1.14 |
snMspsMrpInterconAdminMICPositionControls the MRP Interconnection Client position
in the interconnection setup.
If the value is set to primary(0) the MRP Interconnection Client
is a primary MRP Interconnection Client.
If the value is set to secondary(1) the MRP Interconnection Client
is the secondary MRP Interconnection Client.rw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.24.5.10.1.18 |
snMspsMrpInterconOperMICPositionReads the MRP Interconnection Client position
in the interconnection setup.
If the value is set to primary(0) the MRP Interconnection Client
is a primary MRP Interconnection Client.
If the value is set to secondary(1) the MRP Interconnection Client
is the secondary MRP Interconnection Client.ro Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.24.5.10.1.19 |
snMspsMrpInterconLinkCheckProfileControls the link check sensibility (check frame send interval
and thus link check frame load) of the MRP Interconnection links.
undefined(0) - link check profile not set.
primary_default(1) - 10ms on primary MRP Interconnection link.
secondary_default(2) - 1000ms on secondary MRP Interconnection link.
secondary_high(4) - 10ms on secondary MRP Interconnection link.rw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.24.5.10.1.28 |
snMspsMrpInterconStartDelayTime in [100 ms] that an MRP Interconnection manager/client
will wait before to enable the MRP Interconnection port
even if the MRP Interconnection ring coupling configuration
is not complete.
The maximum value of 65535 (0xFFFF) means indefinite waiting.
Some values are reserved and/or differ in meaning/usage, see below.
-++-
Value (hexadecimal) | Meaning | Usage
-++-
0x0000 | Reserved | -
0x0001 | Value 100 ms = 100 ms | Optional Startup delay
0x0002 | Value 100 ms = 200 ms | Mandatory Startup delay
0x0003 - 0xEA60 | Value 100 ms | Optional Startup delay
0xEA61 - 0xFFFE | Reserved | -
0xFFFF | Wait infinite time | Optional Startup delay
-++-rw INTEGER .1.3.6.1.4.1.4329.20.1.1.1.1.24.5.10.1.29 |
snMspsMrpInterconRowStatusSupport of creation and deletion of rows.
A row can be taken out of service by writing
the value notInService(2).rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.4329.20.1.1.1.1.24.5.10.1.30 |
snMspsSinema OBJECT IDENTIFIER .1.3.6.1.4.1.4329.20.1.1.1.1.25 |
snMspsLoadSave OBJECT IDENTIFIER .1.3.6.1.4.1.4329.20.1.1.1.1.26 |
snMspsLoadSaveRestartRequiredRepresents current state of the device according
to file transfer activities, which are done for files
registered by Load & Save component. If the current
state is 'true', the restart of the device is required.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4329.20.1.1.1.1.26.1 |
snMspsLoadSavePasswords OBJECT IDENTIFIER .1.3.6.1.4.1.4329.20.1.1.1.1.26.5 |
snMspsLoadSaveFilePasswordTableContains files, which are currently
registered by Load & Save component. SEQUENCE OF SnMspsLoadSaveFilePasswordEntry .1.3.6.1.4.1.4329.20.1.1.1.1.26.5.10 |
snMspsLoadSaveFilePasswordEntryThe row in the snMspsLoadSaveFilePasswordTable representing
password settings of configuration files, which are currently
registered by Load & Save component. SnMspsLoadSaveFilePasswordEntry .1.3.6.1.4.1.4329.20.1.1.1.1.26.5.10.1 |
snMspsLoadSaveFileIndexThe unique string representing file type ID. OCTET STRING .1.3.6.1.4.1.4329.20.1.1.1.1.26.5.10.1.1 |
snMspsLoadSaveFileTypeThe file type ID of registered file.
This string is identical to snMspsLoadSaveFileIndex.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.4329.20.1.1.1.1.26.5.10.1.2 |
snMspsLoadSaveFileEnablePasswordSet 'true' if this file type needs a configured password.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4329.20.1.1.1.1.26.5.10.1.5 |
snMspsLoadSaveFilePasswordThe encrypted password value, which is used when accessing
registered file. This value has to be entered by user.rw OCTET STRING .1.3.6.1.4.1.4329.20.1.1.1.1.26.5.10.1.10 |
snMspsLoadSaveFilePasswordStatusCurrent validation status of entered password.
0 - The password value is not considered by the file type.
1 - The password value stored in snMspsLoadSaveFilePassword
is valid for the corresponding file type.
2 - The password value stored in snMspsLoadSaveFilePassword
is invalid for the corresponding file type.
3 - The password value is required by the file type.
4 - The password value is not required by the file type.ro Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.26.5.10.1.15 |
snMspsLoadSaveTftp OBJECT IDENTIFIER .1.3.6.1.4.1.4329.20.1.1.1.1.26.10 |
snMspsLoadSaveTftpServerAddressThe IP address of TFTP server, which stores
the files registered by Load&Save component.rwdeprecated IpAddress .1.3.6.1.4.1.4329.20.1.1.1.1.26.10.1 |
snMspsLoadSaveTftpServerPortThe port number of TFTP server, which stores
the files registered by Load&Save component.rw INTEGER .1.3.6.1.4.1.4329.20.1.1.1.1.26.10.2 |
snMspsLoadSaveTftpServerInetAddressThe Inet address of TFTP server, which stores
the files registered by Load&Save component.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.4329.20.1.1.1.1.26.10.5 |
snMspsLoadSaveTftpServerInetAddressTypeThe Inet address type of TFTP server, which stores
the files registered by Load&Save component.rw InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.4329.20.1.1.1.1.26.10.6 |
snMspsLoadSaveTftpFileTableA list of configuration files, which are currently
registered by Load & Save component. SEQUENCE OF SnMspsLoadSaveTftpFileEntry .1.3.6.1.4.1.4329.20.1.1.1.1.26.10.10 |
snMspsLoadSaveTftpFileEntryThe row in the snMspsLoadSaveTftpFileTable representing
settings of configuration files, which are currently
registered by Load & Save component. SnMspsLoadSaveTftpFileEntry .1.3.6.1.4.1.4329.20.1.1.1.1.26.10.10.1 |
snMspsLoadSaveTftpFileIndexThe unique string representing file type ID. OCTET STRING .1.3.6.1.4.1.4329.20.1.1.1.1.26.10.10.1.1 |
snMspsLoadSaveTftpFileTypeThe file type ID of registered file.
This string is identical to snMspsLoadSaveTftpFileIndex.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.4329.20.1.1.1.1.26.10.10.1.2 |
snMspsLoadSaveTftpFileNameThe file name of registered file. The file name can also contain
the relative path starting from root folder of TFTP server.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.4329.20.1.1.1.1.26.10.10.1.3 |
snMspsLoadSaveTftpFilePresentAvailability of the registered file on the device.
0 - the registered file is currently not present on device
1 - the registered file can be downloaded from device
2 - the registered file can be deleted on the device
3 - the registered file can be downloaded from device and
deleted on devicero Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.26.10.10.1.4 |
snMspsLoadSaveTftpFileLoadSupportedRepresents whether the Load functionality
is supported for this file type.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4329.20.1.1.1.1.26.10.10.1.10 |
snMspsLoadSaveTftpFileSaveSupportedRepresents whether the Save functionality
is supported for this file type.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4329.20.1.1.1.1.26.10.10.1.11 |
snMspsLoadSaveTftpFileDeleteSupportedRepresents whether the Delete functionality
is supported for this file type.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4329.20.1.1.1.1.26.10.10.1.12 |
snMspsLoadSaveTftpFileTransferTableThis conceptual table is an extension of
snMspsLoadSaveTftpFileTable and contains file triggers for initiate
file operations with files registered by Load & Save component. SEQUENCE OF SnMspsLoadSaveTftpFileTransferEntry .1.3.6.1.4.1.4329.20.1.1.1.1.26.10.11 |
snMspsLoadSaveTftpFileTransferEntryThe row in the snMspsLoadSaveTftpFileTransferTable
representing file triggers of configuration files,
which are currently registered by Load & Save component. SnMspsLoadSaveTftpFileTransferEntry .1.3.6.1.4.1.4329.20.1.1.1.1.26.10.11.1 |
snMspsLoadSaveTftpFileLoadWrite access using activate(2) initiates transfer
of registered file from TFTP server to device,
if this functionality is supported for this file type.
The support of functionality is represented in
snMspsLoadSaveTftpFileLoadSupported.
Write access using other values will cause 'bad value'
error. Read access will return following values:
1 - No Load transfers have been done for this file type
since last start of the device.
2 - Activate transfer of registered file from TFTP server
to device. If this file type does not support this
functionality, the 'bad value' error will be returned.
3 - Last transfer of registered file from TFTP server is in progress.
4 - Last transfer of registered file from TFTP server
was successfull. Device restart is not reqired.
5 - Last transfer of registered file from TFTP server
was successfull. Device restart is reqired.
6 - Last transfer of registered file from TFTP server
was not successfull.rw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.26.10.11.1.1 |
snMspsLoadSaveTftpFileSaveWrite access using activate(2) initiates transfer
of registered file from device to TFTP server,
if this functionality is supported for this file type.
The support of functionality is represented in
snMspsLoadSaveTftpFileSaveSupported.
Write access using other values will cause 'bad value'
error. Read access will return following values:
1 - No Save transfers have been done for this file type
since last start of the device.
2 - Activate transfer of registered file from device to
TFTP server. If this file type does not support this
functionality, the 'bad value' error will be returned.
3 - Last transfer of registered file from device is in progress.
4 - Last transfer of registered file from device
was successfull. Device restart is not reqired.
5 - Last transfer of registered file from device
was successfull. Device restart is reqired.
6 - Last transfer of registered file from device
was not successfull.rw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.26.10.11.1.2 |
snMspsLoadSaveTftpFileDeleteWrite access using activate(2) initiates deletion
of registered file on TFTP server,
if this functionality is supported for this file type.
The support of functionality is represented in
snMspsLoadSaveTftpFileDeleteSupported.
Write access using other values will cause 'bad value'
error. Read access will return following values:
1 - No Delete actions have been done for this file type
since device start.
2 - Activate deletion of registered file on TFTP server
If this file type does not support this functionality,
the 'bad value' error will be returned.
3 - Deletion of registered file on TFTP server is in progress.
4 - Last deletion of registered file on TFTP server
was successfull. Restart of the device is not reqired.
5 - Last deletion of registered file on TFTP server
was successfull. Restart of the device is reqired.
6 - Last deletion of registered file on TFTP server
was not successfull.rw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.26.10.11.1.3 |
snMspsLoadSaveSftp OBJECT IDENTIFIER .1.3.6.1.4.1.4329.20.1.1.1.1.26.11 |
snMspsLoadSaveSftpServerInetAddressThe IP address of SFTP server, which stores
the files registered by Load&Save component.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.4329.20.1.1.1.1.26.11.1 |
snMspsLoadSaveSftpServerInetAddressTypeThe Inet address type of SFTP server, which stores
the files registered by Load&Save component.rw InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.4329.20.1.1.1.1.26.11.2 |
snMspsLoadSaveSftpServerPortThe port number of SFTP server, which stores
the files registered by Load&Save component.rw INTEGER .1.3.6.1.4.1.4329.20.1.1.1.1.26.11.3 |
snMspsLoadSaveSftpServerUserThe user ID, which has to be allowed
for login to SFTP server.rw OCTET STRING .1.3.6.1.4.1.4329.20.1.1.1.1.26.11.6 |
snMspsLoadSaveSftpServerPasswordThe user password, which has to be valid
for login with user ID defined in
snMspsLoadSaveSftpServerUser to SFTP server.rw OCTET STRING .1.3.6.1.4.1.4329.20.1.1.1.1.26.11.7 |
snMspsLoadSaveSftpFileTableA list of configuration files, which are currently
registered by Load & Save component. SEQUENCE OF SnMspsLoadSaveSftpFileEntry .1.3.6.1.4.1.4329.20.1.1.1.1.26.11.10 |
snMspsLoadSaveSftpFileEntryThe row in the snMspsLoadSaveSftpFileTable representing
settings of configuration files, which are currently
registered by Load & Save component. SnMspsLoadSaveSftpFileEntry .1.3.6.1.4.1.4329.20.1.1.1.1.26.11.10.1 |
snMspsLoadSaveSftpFileIndexThe unique string representing file type ID. OCTET STRING .1.3.6.1.4.1.4329.20.1.1.1.1.26.11.10.1.1 |
snMspsLoadSaveSftpFileTypeThe file type ID of registered file.
This string is identical to snMspsLoadSaveSftpFileIndex.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.4329.20.1.1.1.1.26.11.10.1.2 |
snMspsLoadSaveSftpFileNameThe file name of registered file. The file name can also contain
the relative path starting from root folder of SFTP server.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.4329.20.1.1.1.1.26.11.10.1.3 |
snMspsLoadSaveSftpFilePresentAvailability of the registered file on the device.
0 - the registered file is currently not present on device
1 - the registered file can be downloaded from device
2 - the registered file can be deleted on the device
3 - the registered file can be downloaded from device and
deleted on devicero Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.26.11.10.1.4 |
snMspsLoadSaveSftpFileLoadSupportedRepresents whether the Load functionality
is supported for this file type.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4329.20.1.1.1.1.26.11.10.1.10 |
snMspsLoadSaveSftpFileSaveSupportedRepresents whether the Save functionality
is supported for this file type.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4329.20.1.1.1.1.26.11.10.1.11 |
snMspsLoadSaveSftpFileDeleteSupportedRepresents whether the Delete functionality
is supported for this file type.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4329.20.1.1.1.1.26.11.10.1.12 |
snMspsLoadSaveSftpFileTransferTableThis conceptual table is an extension of
snMspsLoadSaveSftpFileTable and contains file triggers for initiate
file operations with files registered by Load & Save component. SEQUENCE OF SnMspsLoadSaveSftpFileTransferEntry .1.3.6.1.4.1.4329.20.1.1.1.1.26.11.11 |
snMspsLoadSaveSftpFileTransferEntryThe row in the snMspsLoadSaveSftpFileTransferTable
representing file triggers of configuration files,
which are currently registered by Load & Save component. SnMspsLoadSaveSftpFileTransferEntry .1.3.6.1.4.1.4329.20.1.1.1.1.26.11.11.1 |
snMspsLoadSaveSftpFileLoadWrite access using activate(2) initiates transfer
of registered file from SFTP server to device,
if this functionality is supported for this file type.
The support of functionality is represented in
snMspsLoadSaveSftpFileLoadSupported.
Write access using other values will cause 'bad value'
error. Read access will return following values:
1 - No Load transfers have been done for this file type
since last start of the device.
2 - Activate transfer of registered file from SFTP server
to device. If this file type does not support this
functionality, the 'bad value' error will be returned.
3 - Last transfer of registered file from SFTP server is in progress.
4 - Last transfer of registered file from SFTP server
was successfull. Device restart is not reqired.
5 - Last transfer of registered file from SFTP server
was successfull. Device restart is reqired.
6 - Last transfer of registered file from SFTP server
was not successfull.rw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.26.11.11.1.1 |
snMspsLoadSaveSftpFileSaveWrite access using activate(2) initiates transfer
of registered file from device to SFTP server,
if this functionality is supported for this file type.
The support of functionality is represented in
snMspsLoadSaveSftpFileSaveSupported.
Write access using other values will cause 'bad value'
error. Read access will return following values:
1 - No Save transfers have been done for this file type
since last start of the device.
2 - Activate transfer of registered file from device to
SFTP server. If this file type does not support this
functionality, the 'bad value' error will be returned.
3 - Last transfer of registered file from device is in progress.
4 - Last transfer of registered file from device
was successfull. Device restart is not reqired.
5 - Last transfer of registered file from device
was successfull. Device restart is reqired.
6 - Last transfer of registered file from device
was not successfull.rw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.26.11.11.1.2 |
snMspsLoadSaveSftpFileDeleteWrite access using activate(2) initiates deletion
of registered file on SFTP server,
if this functionality is supported for this file type.
The support of functionality is represented in
snMspsLoadSaveSftpFileDeleteSupported.
Write access using other values will cause 'bad value'
error. Read access will return following values:
1 - No Delete actions have been done for this file type
since device start.
2 - Activate deletion of registered file on SFTP server
If this file type does not support this functionality,
the 'bad value' error will be returned.
3 - Deletion of registered file on SFTP server is in progress.
4 - Last deletion of registered file on SFTP server
was successfull. Restart of the device is not reqired.
5 - Last deletion of registered file on SFTP server
was successfull. Restart of the device is reqired.
6 - Last deletion of registered file on SFTP server
was not successfull.rw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.26.11.11.1.3 |
snMspsReport OBJECT IDENTIFIER .1.3.6.1.4.1.4329.20.1.1.1.1.28 |
snMspsPort OBJECT IDENTIFIER .1.3.6.1.4.1.4329.20.1.1.1.1.29 |
snMspsPortTableTable containing per-port objects in the form of private
extensions of interface objects. SEQUENCE OF SnMspsPortEntry .1.3.6.1.4.1.4329.20.1.1.1.1.29.90 |
snMspsPortEntryInterface entry containing objects at the
subnetwork layer and below for a particular
interface. SnMspsPortEntry .1.3.6.1.4.1.4329.20.1.1.1.1.29.90.1 |
snMspsPortIndexUnique number for each interface. The number is in the range
1 to 26. The number for each interface must remain
constant at least from one re-initialization of the entity's
network management system to the next re-initialization.ro INTEGER .1.3.6.1.4.1.4329.20.1.1.1.1.29.90.1.1 |
snMspsPortFaultMaskStateMask for checking link state of the port.
If a link of a masked as link down (checked-link-down) port
is down then a fault will be generated. If a link of a masked
as link up (checked-link-up) port is up then
a fault will be generated.rw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.29.90.1.2 |
snMspsPortLockStateLock state of the port.
disabled (1) - MAC Learning and Forwarding enabled. Dynamic entries can be added.
enabled (2) - MAC Learning and Forwarding disabled. Dynamic entries alter to static.rw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.29.90.1.3 |
snMspsPortFlowControlStatusCurrent state of Flow Control on the port returned from the hardwarero TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4329.20.1.1.1.1.29.90.1.4 |
snMspsPortStandbyMaskStateMask for standby ports.rw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.29.90.1.6 |
snMspsPortBroadcastBlockingEnable / Disable broadcast blocking. Used to select which ports are
prevented from being forwarded broadcast packets.rw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.29.90.1.7 |
snMspsPortDcpConfigThe administratively desired behavior of the device for DCP frames.
If the associated snMspsPortDcpConfig object has a
value of 'rxOnly(2)', then the device will receive,
but it will not transmit DCP frames on this port.
If the associated snMspsPortDcpConfig object has a
value of 'txAndRx(3)', then the device will transmit
and receive DCP frames on this port.rw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.29.90.1.8 |
snMspsPortUnknownMulticastBlockingEnable / Disable unknown multicast blocking. Used to select which ports are
prevented from being forwarded multicast packets to unknown multicast addresses.rw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.29.90.1.9 |
snMspsPortActiveSetting this object to false(2) forces link down on this ports and its connected devices.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4329.20.1.1.1.1.29.90.1.10 |
snMspsPortUnknownUnicastBlockingEnable / Disable unknown unicast blocking. Used to select which ports are
prevented from being forwarded unicast packets to unknown unicast addresses.rw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.29.90.1.11 |
snMspsPortMediaTypeDefines the currently active media type of the combo port.
Write access is only allowed for combo ports, i.e. ports that consist
of both a copper port and an optical port.
not-available(0) - the port is not a combo port; configuration of media type is not possible
auto (1) - the media type that has a connection is used; if both ports are connected, the optical port is preferred
copper (2) - the copper port is used
optical (3) - the optical port is usedrw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.29.90.1.12 |
snMspsPortEnhPassListCompEnables or disables Enhanced Passive listening Compatibility mode on a specific port.
The global object snMspsEnhancedPassiveListeningCompatibility
must be configured accordingly to activate this configuration.
If the functionality is not available on corresponding device,
not-available(0) will be returned and no other value can be set.rw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.29.90.1.13 |
snMspsPortQoSTrustModenot-available (0) - the port qos trust mode is not supported
untrust (1) - packet qos parameters are assigned as per
port default priority settings
trust-cos (2) - if the packet is tagged the qos parameters
are assigned according to User Priority field, else like untrust
trust-dscp (3) - if the packet is IPv4/IPv6 qoS parameters
are assigned to the Dscp field or remapped Dscp, else like untrust
trust-cos-dscp (4) - if the packet is IPv4/IPv6 the packet is assigned like trustdscp
else if the packet is tagged like trustcos else like untrustrw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.29.90.1.14 |
snMspsPortBlockStatenot-available (0) - the port block state analysis is not supported
forwarding (1) - not blocked by any configuration or protocol
ring-redundancy (2) - blocked as per ring-redundancy state assigned
spanning-tree (3) - blocked as per spanning-tree state assigned
loop-detected (4) - blocked as per loop-detection state assigned
down-in-bundle (5) - blocked as member of an aggregation
la-loop-detected (6) - blocked as per loop-detection state of LA
la-spanning-tree (7) - blocked as per spanning-tree state of LA
link-down (8) - blocked as per operative link state
admin-down (9) - blocked as per configured admin state
power-down (10) - blocked as per configured power state
standby (11) - blocked as per standby state assigned
link-check (12) - blocked as per link-check state assigned
mrp-interconnection (13) - blocked as per mrp-interconnection state assignedro Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.29.90.1.15 |
snMspsPortRouterAdvertisementBlockingnot-available (0) - Ipv6 Router Advertisements blocking not supported
enabled (1) - Ipv6 Router Advertisements blocking enabled
disabled (2) - Ipv6 Router Advertisements blocking disabledrw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.29.90.1.20 |
snMspsPortAdminMacLearningStatusTruth value used to configure the unicast MAC learning Admin status
for the port.
Value true (1), allows the unicast MAC learning on the port.
Value false(2), disables the unicast MAC learning on the port.
Status can not be set to false (2), if the device does not
support this featurerw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4329.20.1.1.1.1.29.90.1.25 |
snMspsPortMacLearningFlushnot-available (0) - This feature is not supported.
disabled (1) - On link down, learnt MAC will not be flushed
port-flush (2) - On link down, learnt MAC will be flushed only on this port
full-flush (3) - On link down, learnt MAC will be flushed for the entire switchrw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.29.90.1.30 |
snMspsPortNOACtrlModeSets the port to access with Operational Technology (OT) Network or Information Technology (IT) Network or both.
Support only for physical ports and not for LA ports.rw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.29.90.1.35 |
snMspsAcl OBJECT IDENTIFIER .1.3.6.1.4.1.4329.20.1.1.1.1.30 |
snMspsLog OBJECT IDENTIFIER .1.3.6.1.4.1.4329.20.1.1.1.1.31 |
snMspsPnio OBJECT IDENTIFIER .1.3.6.1.4.1.4329.20.1.1.1.1.32 |
snMspsNtp OBJECT IDENTIFIER .1.3.6.1.4.1.4329.20.1.1.1.1.33 |
snMspsIf OBJECT IDENTIFIER .1.3.6.1.4.1.4329.20.1.1.1.1.34 |
snMspsIfMainTableA list of all the interface entries in the system.
This table contains objects which are applicable to all
types of interfaces in the system. This table can be used
to monitor all the interface types. However only virtual and
logical interfaces could be created via this table.
Physical interfaces were created automatically during system initialization
and cannot be added or removed. This table is a
proprietary extension to the standard ifTable and
ifXTable. The index to this table has the semantics of
the MIB-2 ifIndex. SEQUENCE OF SnMspsIfMainEntry .1.3.6.1.4.1.4329.20.1.1.1.1.34.4 |
snMspsIfMainEntryAn entry containing management information applicable
to a particular interface. SnMspsIfMainEntry .1.3.6.1.4.1.4329.20.1.1.1.1.34.4.1 |
snMspsIfMainIndexA unique value, greater than zero, for each
interface. This object is identical to the ifIndex
of the standard MIB-2 ifTable. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.4329.20.1.1.1.1.34.4.1.1 |
snMspsIfMainTypeThe type/protocol of interface. Specification of
the object is mandatory for all interfaces. This
value should be specified after the row creation
in the snMspsIfMainTable and before setting any other
object in this table. Once the type is specified,
it cannot be changed - the interface should be
deleted for changing the type of the interface.
The ethernetCsmacd(6), iso88025TokenRing(9), aal5(49),
async(84) and hdlc(118) are physical interfaces while
all other types are virtual or logical interfaces.
Specific ifIndex ranges are reserved for different interface types.
Creation of different types of interfaces is possible only within
their corresponding ifIndex range. So the snMspsIfMainType should be
configured corresponding to the ifIndex range reserved for that
particular interface type.
pip interface type will be used vritual Provider Instance port in
PBB bridge mode. physical PIPs can be created using ethernetCsmacd .
Following is the mapping of different port types and there snMspsIfMaintype values.
External ports
Port: snMspsIfMaintype Port type
CNP- Ctagged 6 - customerNetworkPortCtagged (9)
CNP - Port based 6 - customerNetworkPortPortBased (2)
CNP- Stagged 6 - customerNetworkPortStagged (3)
PNP 6 - providerNetworkPort (1)
PIP 6 - providerInstancePort (11)
CBP 6 - customerBackbonePort (12)
Internal ports
VIP 209 - virtualInstancePort (10)
PIP 248 - providerInstancePort (11)
CBP 209 - customerBackbonePort (12)
brgPort will be used to create virtual PBB ports other than PIPs- VIPs and CBPs.
The propVirtual type denotes properietary logical interfaces. These
type of interfaces can be associated with a {physical interface,
switch instance} for the purpose of sharing the physical interface
to more than one context and thus realising Switch Instance Sharing
of a physical interface.rw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.34.4.1.2 |
snMspsIfMainMtuThe MTU for the interface as shown to the higher
interface sub-layer (this value should not include
the encapsulation or header added by the interface).
If IP is operating over the interface, then this
value indicates the IP MTU over this interface.
For changing the MTU of any interface, the interface
must be brought down first - changing MTU while the
interface is administratively up is not permitted.
If not specified during interface creation, a default
value is assigned based on the snMspsIfMainType given to
the particular interface.
While configuring for logical VLAN interfaces, care
should be taken to, configure this value as the
lowest of the MTU values of the member ports.rw Integer32 .1.3.6.1.4.1.4329.20.1.1.1.1.34.4.1.3 |
snMspsIfMainAdminStatusThe desired state of the interface. This object
can be set only when the snMspsIfMainRowStatus of the
interface is active. This object has the semantics
of the ifAdminStatus of the standard ifTable.
The testing(3) state indicates that no operational
packets can be passed - this state is not currently
supported.
When a managed system initializes, all
interfaces start with snMspsIfMainAdminStatus in the
down(2) state, it's a default state also. As a result
of either explicit management action or per
configuration information retained by the managed
system, snMspsIfMainAdminStatus is then changed to
the up (1) state (or remains in the
down(2) state).rw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.34.4.1.4 |
snMspsIfMainOperStatusThe current operational state of the interface.
The testing (3) state indicates that no operational
packets can be passed - this state is not supported
currently.
If snMspsIfMainAdminStatus is down (2)
then snMspsIfMainOperStatus would be down (2). If
snMspsIfMainAdminStatus is changed to up (1) then
snMspsIfMainOperStatus should change to up (1) if the
interface is ready to transmit and receive
work traffic; it should change to dormant (5)
the interface is waiting for external actions
(such as a serial line waiting for an incoming
connection); it should change to lowerLayerDown(7)
state if it cannot be made up as the interface sub-layer
below it is down; it should remain in the down (2) state
if and only if there is a fault that prevents it
from going to the up (1) state; it should remain in
the notPresent (6) state if the interface has
missing (typically, hardware) components.
The status unknown(4) is shown when it is not possible
to determine the exact status of the interface - e.g.
the interface sub-layer is performing negotiations -
during this period the interface is not up but at the
same time, it is not a fault condition and hence it
cannot be shown as down - in such periods the status
is shown as unknown.
This object has the semantics of the ifOperStatus of the
standard ifTable.ro Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.34.4.1.5 |
snMspsIfMainEncapTypeThe encapsulation type to be used over the interface.
For Ethernet interfaces, the default encapsulation
type is ethernetV2(8). The other possible encapsulation
is llcSnap(6). If other(1) is specified then an
automatic encapsulation type learning method is used
in ARP for determining the encapsulation for unicast
destinations while the multicast and broadcast destinations
use ethernetV2(8).
For PPP and MLPPP interfaces, the encapsulation type can
only be other(1) and this is the default value.
For FR VCs, the value can be nlpid(2) (for carrying protocols
which have NLPID) or nlpidSnap(3) (for other protocols). The
default is nlpid(2) and the types of protocols supported are
inferred from the stack-layering implemented over the
interface.
For X.25 VCs, the value can be nlpid(2) or nlpidSnap(3)
(where the VC can carry multiplexed protocol traffic with
each data packet containing the NLPID or SNAP header) or
cudNlpid(4) or cudNlpidSnap(5) (where the CUD specifies
the NLPID of the protocol or SNAP and the data packets do
not contain these headers - for dedicated VCs). The default
is cudNlpid(4).
For ATM VCs, the default is llcSnap(6) but the
vcMultiplexed(7) encapsulation is also supported.
This object is not applicable to other interfaces.rw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.34.4.1.6 |
snMspsIfMainBrgPortTypeThe Bridge port type of this specified switch port.
Bridge Port type can be specified only for switch ports and not for
router ports, IVR interfaces and I-LAN Interfaces.
providerNetworkPort - Port Connected to a single Provider.
SVLAN Classification is based on only the PVID configured for the
port for untagged packets.
customerNetworkPortPortBased - Port in the S-VLAN component that
can transmit or received frames for single customer.
All packets received on this port, are mapped to one single service
instance identified by the PVID of that Port.
Acceptable Port Type will be always Admit only Untagged or Priority
Tagged Frames on this port.
customerNetworkPortStagged - Port in the S-VLAN component that
can transmit or received frames for single customer.
VLAN classification on this interface will be based on the S-tag
received or on the PVID of the port. Ingress Filtering will be
always enabled on this port.
customerEdgePort - Port in a Provider Edge Bridge connected to a
single customer. Multiple services can be provide on this port.
The Packets received on this interface will be first classified
to a CVLAN. CVLAN classification can be based on the Vid
in the C-Tag present in the packet (if it C-tagged packet) or from
the pvid of the port. Service instance selection (S-VLAN selection)
for a frame is done based on the entry present in the C-VID
registration table for the pair (C-VID, reception Port).
CustomerEdgePort configuration is allowed only in Provider Edge
Bridges.
propCustomerEdgePort - Port connected to a single customer, where
multiple services can be provided based on only Proprietary SVLAN
classification tables. S-VLAN classification will not happen based on
C-VID registration table on this port. propCustomerEdgePort
configuration is allowed only in Provider Edge Bridges.
propCustomerNetworkPort - Port connected to a single customer, where
multiple service can be provided based on CVLANs by assigning one of
the Proprietary SVLAN classification tables to this port. The
services can also be assigned using other proprietary SVLAN
classification tables where CVLAN is not the index of the table.
propProviderNetworkPort - Port connected to a Q-in-Q Bridge located
inside Provider Network. This port is part of S-VLAN component.
If packets to be tagged and sent out of this port will have 0x8100
as the ether type. Similarly pakcets with standard Q tag (ether type
as 0x8100) received will be considered as S-Tagged packets.
customerBridgePort - Type of the port to be used in customer
bridges as well in Provider(Q-in-Q) bridges. This type is not valid
in Provider Core bridges as well as Provider Edge bridge.
customerNetworkPortCtagged - Port in the I component that
can transmit or received frames for single customer.
VLAN classification on this interface will be based on the C-tag
received or on the default CVID of the port. Ingress Filtering will be
always enabled on this port.
virtualInstancePort - A Bridge Port on an I-component in a Backbone Edge Bridge
that provides access to a single backbone service instance.
providerInstancePort - The set of Virtual Instance Ports that are supported
by a single instance of the device.
customerBackbonePort - A Backbone Edge Bridge Port that can receive and transmit
I-tagged frames for multiple customers, and assign B-VIDs and translate I-SID on
the basis of the received I-SID.
In Customer bridges and in Provider Bridges only customerPort option
is allowed.
In Provider backbone bridge only customerNetworkPort, providerNetworkPort
and customerBackbonePort type of ports are allowed.
Bridge Port Type cannot be set for a port-channel port, if some
physical ports are aggregated in it.
Also Bridge Port type cannot be set for a port, if part of a
port-channel.
Whenever the Bridge port type changes, the previous configuration
associated with the port will be flushed.
For example.
whenever CNP(STagged) and PNP port types are changed to any
other port type,
- The unicast entries learnt on this port and
- The VID translation table entries associated with the port
will be flushed.
Whenever CEP port type is changed to any other port type,
- The unicast entries learnt on this port
- The C-VID registration table entries associated with the port
- The PEP configuration table entries
- The service priority regeneration table entries
will be flushed.
Even the vlan membership of the port will be removed when the
Pbport type is changed.rw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.34.4.1.7 |
snMspsIfMainRowStatusA RowStatus variable for addition (except for physical interfaces),
deletion (except for physical interfaces ) and in-activation
of the interfaces. Specification of the object is mandatory
for all interfaces.
When the status is active, the interface is created and
ready to use in the respective protocol modules.
When the status is notInService, the interface has not been
registered with the respective protocol modules and as such
those modules are not aware of the existence of the interface
- creation is hence, incomplete. Setting an active interface
to notInService results in de-registration/deletion of the
interface from the respective protocol modules and all the
configurations associated with that interface in those modules
may be lost.
Deletion of an interface, may affect the status of other
interfaces which are layered above or below it in the Interface
Stack (ifStackTable) and may result in other interfaces being
made notReady or notInService.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.4329.20.1.1.1.1.34.4.1.8 |
snMspsIfMainSubTypeThis object stores the subType value of the specified interface.
Configuration of this object is not mandatory.By default
Sub type value will be updated based on the hardware link speed.rw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.34.4.1.9 |
snMspsIfIpTableA list of all the interface entries in the system which
are registered with IP.
This table contains objects which are applicable for the
management of IP over the network interfaces
in the system.
This table is a extension to the snMspsIfMainTable.
The index to this table has the semantics of
the snMspsIfMainIndex of the snMspsIfMainTable.
Entries are created automatically in this table for
any interface sub-layer which is layer below IP using
the ifStackTable. Similarly, entries are deleted from
this table when the interface's layering below IP is
removed. SEQUENCE OF SnMspsIfIpEntry .1.3.6.1.4.1.4329.20.1.1.1.1.34.5 |
snMspsIfIpEntryAn entry containing management information applicable
to a particular interface over which IP is operating. SnMspsIfIpEntry .1.3.6.1.4.1.4329.20.1.1.1.1.34.5.1 |
snMspsIfIpAddrAllocMethodThe mechanism to be used for allocation of IP
address for this interface.
The value negotiation can be used only for PPP
and MLPPP interfaces which support obtaining of
IP addresses through negotiation.
The dynamic(3) option takes an IP
address dynamically from the available
server (dhcp/bootp/rarp) according to the
protocol specified in snMspsIfIpAddrAllocProtocol.
If the method specified is manual and the IP
address is not provided (then the interface
would be treated as a un-numbered interface.rw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.34.5.1.1 |
snMspsIfIpAddrSpecifies the IP address given to this
interface. The specification of this object is
mandatory for all network interfaces (Ethernet,
FR VC, IPoA interface, PPP link - not under MP,
MP interface and X.25 VC). If the interface is
not a network interface then the default value
of 0.0.0.0 is assigned and the interface is
treated as a un-numbered interface by IP.rw IpAddress .1.3.6.1.4.1.4329.20.1.1.1.1.34.5.1.2 |
snMspsIfIpSubnetMaskSpecifies the IP Subnet Mask for this
interface. The value should be specified only
for network interfaces and any valid VLSM is
accepted.
If not specified, this object takes the default
subnet mask value based on the class of the IP
address configured for the interface.rw IpAddress .1.3.6.1.4.1.4329.20.1.1.1.1.34.5.1.3 |
snMspsIfIpBroadcastAddrSpecifies the IP broadcast address for this
interface. The value should be specified only
for network interfaces and any valid broadcast
address based on a valid VLSM is accepted.
If not specified, this object takes the default
value based on the class of the IP
address configured for the interface.rw IpAddress .1.3.6.1.4.1.4329.20.1.1.1.1.34.5.1.4 |
snMspsIfIpForwardingEnableSpecifies whether IP forwarding is enable on
this interface. Disabling IP forwarding on an
interface will result in packets which are to
be forwarded on that interface being dropped
and ICMP error messages being generated for the
packets.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4329.20.1.1.1.1.34.5.1.5 |
snMspsIfIpAddrAllocProtocolSpecifies the protocol to be used to obtain
IP address for this interface. This object is
valid only when snMspsIfIpAddrAllocMethod is set to
dynamic (3).
Currently rarp (1) option is not
supported. The assigned value will be effective
only when the interface admin status changesrw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.34.5.1.6 |
snMspsIfIpInterfaceNameInterface name for IP interfacesrw DisplayString .1.3.6.1.4.1.4329.20.1.1.1.1.34.5.1.7 |
snMspsIfIvrTableA list of all the interfaces in the system with IVR related
configurations.
This table is an extension to the snMspsIfMainTable. The index to
this table has the semantics of the snMspsIfMainIndex of the
snMspsIfMainTable. SEQUENCE OF SnMspsIfIvrEntry .1.3.6.1.4.1.4329.20.1.1.1.1.34.8 |
snMspsIfIvrEntryAn entry containing IVR-related information applicable
to a interface. SnMspsIfIvrEntry .1.3.6.1.4.1.4329.20.1.1.1.1.34.8.1 |
snMspsIfIvrBridgedIfaceIndicates if this interface is a Bridged interface
or not.
A value of 'TRUE' indicates that this interface is
a Bridged interface and is capable of performing
bridging of packets through this interface.
A value of 'FALSE' indicates that this
interface is a Routed interface and is capable of
performing routing of packets through this interface.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4329.20.1.1.1.1.34.8.1.1 |
snMspsIfIvrLoopBackIfaceIndicates if this interface is a IVR Loopback interface
or not.
A value of 'TRUE' indicates that this IVR interface is
a Loopback Interface.
A value of 'FALSE' indicates that this IVR
interface is not a Loopback interface.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4329.20.1.1.1.1.34.8.1.2 |
snMspsIfSecondaryIpAddressTableA list of secondary IP addresses configured over the
interfaces registered with IP.
This table is a extension to the snMspsIfMainTable.
The index to this table has the semantics of
the snMspsIfMainIndex of the snMspsIfMainTable.
Secondary IpAddress configuration should not override the
primary ip address configured for any of the interface
Updation of entries in this table are not allowd when
RowStatus is active SEQUENCE OF SnMspsIfSecondaryIpAddressEntry .1.3.6.1.4.1.4329.20.1.1.1.1.34.11 |
snMspsIfSecondaryIpAddressEntryAn entry contains the information associated with the
secondary(additional) ip address configured to a particular
interface. SnMspsIfSecondaryIpAddressEntry .1.3.6.1.4.1.4329.20.1.1.1.1.34.11.1 |
snMspsIfSecondaryIpAddressSpecifies the Secondary IP address associated with the
interface IpAddress .1.3.6.1.4.1.4329.20.1.1.1.1.34.11.1.1 |
snMspsIfSecondaryIpSubnetMaskSpecifies the IP Subnet Mask associted with the
secondary ip address configuration. The value should be
specified only for network interfaces and any valid
VLSM is accepted.
If not specified, this object takes the default
subnet mask value based on the class of the IP
address configured for the interface.rw IpAddress .1.3.6.1.4.1.4329.20.1.1.1.1.34.11.1.2 |
snMspsIfSecondaryIpBroadcastAddrSpecifies the IP broadcast address associated with
the configured secondary IP address. The value should be
specified only for network interfaces and any valid
broadcast address based on a valid VLSM is accepted.
If not specified, this object takes the default
value based on the class of the IP
address configured for the interface.rw IpAddress .1.3.6.1.4.1.4329.20.1.1.1.1.34.11.1.3 |
snMspsIfSecondaryIpRowStatusThis object is used to manage creation and deletion of rows
in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.4329.20.1.1.1.1.34.11.1.4 |
snMspsIfSecondaryIpInterfaceNameInterface name for secondary IP interfacesrw DisplayString .1.3.6.1.4.1.4329.20.1.1.1.1.34.11.1.5 |
snMspsIfOverviewIpAddressTableA list of primary and secondary IP addresses configured over the
interfaces registered with IP. SEQUENCE OF SnMspsIfOverviewIpAddressEntry .1.3.6.1.4.1.4329.20.1.1.1.1.34.15 |
snMspsIfOverviewIpAddressEntryAn entry contains the information associated with the primary and
secondary(additional) ip addresses configured to a particular
interface. SnMspsIfOverviewIpAddressEntry .1.3.6.1.4.1.4329.20.1.1.1.1.34.15.1 |
snMspsIfOverviewIpAddressShows primary and secondary IP addresses associated with the
interface IpAddress .1.3.6.1.4.1.4329.20.1.1.1.1.34.15.1.1 |
snMspsIfOverviewIpSubnetMaskShows the IP Subnet Mask associted with the
primary and secondary ip addresses configuration.ro IpAddress .1.3.6.1.4.1.4329.20.1.1.1.1.34.15.1.2 |
snMspsIfOverviewIpBroadcastAddrShows the IP broadcast address associated with
the configured primary and secondary IP addresses.ro IpAddress .1.3.6.1.4.1.4329.20.1.1.1.1.34.15.1.3 |
snMspsIfOverviewIpTypeShows IP address type: primary or secondary.ro Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.34.15.1.4 |
snMspsIfOverviewIpAddressACDStatusShows IPV4 Address Collision Detection Status.ro Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.34.15.1.5 |
snMspsIfIvrMappingTableThis table is used to configure the list of vlans to be
associated for an IVR interface.
The primary Index to this table can only be a IVR interface.
Only considered if device supports corresponding functionality,
otherwise any set operation will fail with an inconsistentValue error
and get will return empty. SEQUENCE OF SnMspsIfIvrMappingEntry .1.3.6.1.4.1.4329.20.1.1.1.1.34.18 |
snMspsIfIvrMappingEntryEach entry in this table gives an assoicated vlan to an IVR
interface. SnMspsIfIvrMappingEntry .1.3.6.1.4.1.4329.20.1.1.1.1.34.18.1 |
snMspsIfIvrAssociatedVlanThis object specifies one of the associated VLANs for a given
IVR interface. Vlan Id associated with an IVR interface during
IVR interface creation, should not be configured as
snMspsIfIvrAssociatedVlan for that IVR interface.
snMspsIfIvrAssociatedVlan and the primary vlan (vlan associated with
IVR during IVR creation) for an IVR interface should be in the
same Layer 2 context. VlanId (Q-BRIDGE-MIB) .1.3.6.1.4.1.4329.20.1.1.1.1.34.18.1.1 |
snMspsIfIvrMappingRowStatusDenotes the Row Status for port isolation table entry.
Only 'CreateAndGo' and 'destroy' values are allowed for this
object. 'CreateAndWait' and 'notInService' values are not allowed.
Example:
To add vlans 2, 3 as associated vlans to an IVR interface with
interface index as 10 in this table, the following sequence
to be followed:
1. Set the snMspsIfIvrMappingRowStatus as 'CreateAndGo' for the
entry with index
(snMspsIfMainIndex = 10, snMspsIfIvrAssociatedVlan = 2)
2. Set the snMspsIfIvrMappingRowStatus as 'CreateAndGo' for the
entry with index
(snMspsIfMainIndex = 10, snMspsIfIvrAssociatedVlan = 3)
To delete vlan 3 from the list of associated vlans for an IVR
interface with IfIndex = 10 ports, do the following:
Set the snMspsIfIvrMappingRowStatus as 'destroy' for the
entry with index
(snMspsIfMainIndex = 10, snMspsIfIvrAssociatedVlan = 3).rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.4329.20.1.1.1.1.34.18.1.2 |
snMspsKeyPlug OBJECT IDENTIFIER .1.3.6.1.4.1.4329.20.1.1.1.1.35 |
snMspsLoopDetection OBJECT IDENTIFIER .1.3.6.1.4.1.4329.20.1.1.1.1.36 |
snMspsPtp OBJECT IDENTIFIER .1.3.6.1.4.1.4329.20.1.1.1.1.37 |
snMspsPoe OBJECT IDENTIFIER .1.3.6.1.4.1.4329.20.1.1.1.1.38 |
snMspsCableTester OBJECT IDENTIFIER .1.3.6.1.4.1.4329.20.1.1.1.1.44 |
snMspsSfp OBJECT IDENTIFIER .1.3.6.1.4.1.4329.20.1.1.1.1.46 |
snMspsSfpTableTable containing per-port objects in the form of private
extensions of interface objects. SEQUENCE OF SnMspsSfpEntry .1.3.6.1.4.1.4329.20.1.1.1.1.46.10 |
snMspsSfpEntryInterface entry containing objects at the
subnetwork layer and below for a particular
interface. SnMspsSfpEntry .1.3.6.1.4.1.4329.20.1.1.1.1.46.10.1 |
snMspsSfpIndexUnique number for each interface. The number is in the range
1 to 52. The number for each interface must remain
constant at least from one re-initialization of the entity's
network management system to the next re-initialization.ro INTEGER .1.3.6.1.4.1.4329.20.1.1.1.1.46.10.1.1 |
snMspsSfpStatusIndicates whether a SFP device in currently plugged in on this interfacero TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4329.20.1.1.1.1.46.10.1.2 |
snMspsSfpNameThe name of the SFP devicero DisplayString .1.3.6.1.4.1.4329.20.1.1.1.1.46.10.1.3 |
snMspsSfpModelThe model of the SFP devicero DisplayString .1.3.6.1.4.1.4329.20.1.1.1.1.46.10.1.4 |
snMspsSfpRevisionThe revision number of the SFP devicero DisplayString .1.3.6.1.4.1.4329.20.1.1.1.1.46.10.1.5 |
snMspsSfpSerialThe serial number of the SFP devicero DisplayString .1.3.6.1.4.1.4329.20.1.1.1.1.46.10.1.6 |
snMspsSfpNominalBitrateThe nominal bitrate [MBit/s] of the SFP devicero INTEGER .1.3.6.1.4.1.4329.20.1.1.1.1.46.10.1.7 |
snMspsSfpMaxLinkLength50The maximum link length(50/125um) of the SFP devicero INTEGER .1.3.6.1.4.1.4329.20.1.1.1.1.46.10.1.8 |
snMspsSfpMaxLinkLength62The maximum link length(62/125um) of the SFP devicero INTEGER .1.3.6.1.4.1.4329.20.1.1.1.1.46.10.1.9 |
snMspsSfpTemperatureThe temperature of the SFP device in 1/100 degree Celsiusro INTEGER .1.3.6.1.4.1.4329.20.1.1.1.1.46.10.1.10 |
snMspsSfpTemperatureMinMinimum supported temperature of the SFP device in 1/100 degree Celsiusro INTEGER .1.3.6.1.4.1.4329.20.1.1.1.1.46.10.1.11 |
snMspsSfpTemperatureMaxMaximum supported temperature of the SFP device in 1/100 degree Celsiusro INTEGER .1.3.6.1.4.1.4329.20.1.1.1.1.46.10.1.12 |
snMspsSfpVoltageThe voltage of the SFP devicero INTEGER .1.3.6.1.4.1.4329.20.1.1.1.1.46.10.1.13 |
snMspsSfpVoltageMinMinimum supported voltage of the SFP devicero INTEGER .1.3.6.1.4.1.4329.20.1.1.1.1.46.10.1.14 |
snMspsSfpVoltageMaxMaximum supported voltage of the SFP devicero INTEGER .1.3.6.1.4.1.4329.20.1.1.1.1.46.10.1.15 |
snMspsSfpCurrentThe bias current of the SFP devicero INTEGER .1.3.6.1.4.1.4329.20.1.1.1.1.46.10.1.16 |
snMspsSfpCurrentMinMinimum supported bias current of the SFP devicero INTEGER .1.3.6.1.4.1.4329.20.1.1.1.1.46.10.1.17 |
snMspsSfpCurrentMaxMaximum supported bias current of the SFP devicero INTEGER .1.3.6.1.4.1.4329.20.1.1.1.1.46.10.1.18 |
snMspsSfpRxPowerThe receive power of the SFP device in units of 0.1 uWro INTEGER .1.3.6.1.4.1.4329.20.1.1.1.1.46.10.1.19 |
snMspsSfpRxPowerMinMinimum supported receive power of the SFP device in units of 0.1 uWro INTEGER .1.3.6.1.4.1.4329.20.1.1.1.1.46.10.1.20 |
snMspsSfpRxPowerMaxMaximum supported receive power of the SFP device in units of 0.1 uWro INTEGER .1.3.6.1.4.1.4329.20.1.1.1.1.46.10.1.21 |
snMspsSfpTxPowerThe transmit power of the SFP device in units of 0.1 uWro INTEGER .1.3.6.1.4.1.4329.20.1.1.1.1.46.10.1.22 |
snMspsSfpTxPowerMinMinimum supported transmit power of the SFP device in units of 0.1 uWro INTEGER .1.3.6.1.4.1.4329.20.1.1.1.1.46.10.1.23 |
snMspsSfpTxPowerMaxMaximum supported transmit power of the SFP device in units of 0.1 uWro INTEGER .1.3.6.1.4.1.4329.20.1.1.1.1.46.10.1.24 |
snMspsSfpRxPowerdBmThe receive power of the SFP device in units of 0.1 dBm. If this is -999 power is 0 uWro INTEGER .1.3.6.1.4.1.4329.20.1.1.1.1.46.10.1.32 |
snMspsSfpRxPowerMindBmMinimum supported receive power of the SFP device in units of 0.1 dBm. If this is -999 power is 0 uWro INTEGER .1.3.6.1.4.1.4329.20.1.1.1.1.46.10.1.33 |
snMspsSfpRxPowerMaxdBmMaximum supported receive power of the SFP device in units of 0.1 dBm. If this is -999 power is 0 uWro INTEGER .1.3.6.1.4.1.4329.20.1.1.1.1.46.10.1.34 |
snMspsSfpTxPowerdBmThe transmit power of the SFP device in units of 0.1 dBm. If this is -999 power is 0 uWro INTEGER .1.3.6.1.4.1.4329.20.1.1.1.1.46.10.1.35 |
snMspsSfpTxPowerMindBmMinimum supported transmit power of the SFP device in units of 0.1 dBm. If this is -999 power is 0 uWro INTEGER .1.3.6.1.4.1.4329.20.1.1.1.1.46.10.1.36 |
snMspsSfpTxPowerMaxdBmMaximum supported transmit power of the SFP device in units of 0.1 dBm. If this is -999 power is 0 uWro INTEGER .1.3.6.1.4.1.4329.20.1.1.1.1.46.10.1.37 |
snMspsDst OBJECT IDENTIFIER .1.3.6.1.4.1.4329.20.1.1.1.1.54 |
snMspsGuestVlan OBJECT IDENTIFIER .1.3.6.1.4.1.4329.20.1.1.1.1.55 |
snMspsMacAuth OBJECT IDENTIFIER .1.3.6.1.4.1.4329.20.1.1.1.1.56 |
snMspsEthernetIp OBJECT IDENTIFIER .1.3.6.1.4.1.4329.20.1.1.1.1.62 |
snMspsIpACD OBJECT IDENTIFIER .1.3.6.1.4.1.4329.20.1.1.1.1.63 |
snMspsNatv2 OBJECT IDENTIFIER .1.3.6.1.4.1.4329.20.1.1.1.1.75 |
snMspsDiagnostics OBJECT IDENTIFIER .1.3.6.1.4.1.4329.20.1.1.1.1.79 |
snMspsDot1ad OBJECT IDENTIFIER .1.3.6.1.4.1.4329.20.1.1.1.1.81 |
snMspsLinkCheck OBJECT IDENTIFIER .1.3.6.1.4.1.4329.20.1.1.1.1.82 |
snMspsLinkCheckFrameLossStatsTableTable containing per-port, per-instance objects. SEQUENCE OF SnMspsLinkCheckFrameLossStatsEntry .1.3.6.1.4.1.4329.20.1.1.1.1.82.7 |
snMspsLinkCheckFrameLossStatsEntryLink Check frame loss statistic per-port, per-instance entry. SnMspsLinkCheckFrameLossStatsEntry .1.3.6.1.4.1.4329.20.1.1.1.1.82.7.1 |
snMspsFrameLossStatsInstanceLink Check frame loss statistics instance of port. INTEGER .1.3.6.1.4.1.4329.20.1.1.1.1.82.7.1.2 |
snMspsFrameLossStatsRatingRating of link state if threshold is exceeded.rw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.82.7.1.5 |
snMspsFrameLossStatsIntervalInterval [ms] of frame loss calculation.rw INTEGER .1.3.6.1.4.1.4329.20.1.1.1.1.82.7.1.8 |
snMspsFrameLossStatsThresholdFrame loss rate threshold [per mill].rw INTEGER .1.3.6.1.4.1.4329.20.1.1.1.1.82.7.1.11 |
snMspsFrameLossStatsCurrentRateCurrent frame loss rate [per mill].ro INTEGER .1.3.6.1.4.1.4329.20.1.1.1.1.82.7.1.14 |
snMspsLinkCheckPacketErrStatsTableTable containing per-port, per-type objects. SEQUENCE OF SnMspsLinkCheckPacketErrStatsEntry .1.3.6.1.4.1.4329.20.1.1.1.1.82.9 |
snMspsLinkCheckPacketErrStatsEntryPacket errors statistic per-type entry SnMspsLinkCheckPacketErrStatsEntry .1.3.6.1.4.1.4329.20.1.1.1.1.82.9.1 |
snMspsPacketErrStatsTypePacket error type. Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.82.9.1.3 |
snMspsPacketErrStatsRatingRating of link state if threshold is exceeded.rw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.82.9.1.6 |
snMspsPacketErrStatsThresholdPacket error increase threshold.ro Counter32 .1.3.6.1.4.1.4329.20.1.1.1.1.82.9.1.9 |
snMspsPacketErrStatsIncreasePacket error increase since Link Check state is 'running'.ro Counter32 .1.3.6.1.4.1.4329.20.1.1.1.1.82.9.1.12 |
snMspsLinkCheckPortTableTable containing per-port objects. SEQUENCE OF SnMspsLinkCheckPortEntry .1.3.6.1.4.1.4329.20.1.1.1.1.82.10 |
snMspsLinkCheckPortEntryLink Check per-port entry. SnMspsLinkCheckPortEntry .1.3.6.1.4.1.4329.20.1.1.1.1.82.10.1 |
snMspsLinkCheckPortIndexPort number of Link Check port.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.4329.20.1.1.1.1.82.10.1.1 |
snMspsLinkCheckPortAdminStateLink Check state to be usedrw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.82.10.1.2 |
snMspsLinkCheckPortOperStateLink Check operating statero Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.82.10.1.3 |
snMspsLinkCheckPortModeIn advanced mode the port will be disabled after Link Check breakdownrw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.82.10.1.6 |
snMspsLinkCheckPortAdvStatePort state in advanced modero Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.82.10.1.9 |
snMspsLinkCheckPortAdvResetresetting a port that has been disabled after Link Check advanced mode breakdown detectionrw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.82.10.1.12 |
snMspsLinkCheckPortFramesInnumber of received Link Check framesro Counter32 .1.3.6.1.4.1.4329.20.1.1.1.1.82.10.1.15 |
snMspsLinkCheckPortFramesOutnumber of sent Link Check framesro Counter32 .1.3.6.1.4.1.4329.20.1.1.1.1.82.10.1.18 |
snMspsDas OBJECT IDENTIFIER .1.3.6.1.4.1.4329.20.1.1.1.1.83 |
snMspsDualNetAccess OBJECT IDENTIFIER .1.3.6.1.4.1.4329.20.1.1.1.1.88 |
snMspsDualNetAccessScalars OBJECT IDENTIFIER .1.3.6.1.4.1.4329.20.1.1.1.1.88.1 |
snMspsDualNetAccessAdminModeThe Configured Admin mode for the Dual Network Access Module.
The value standalone (0) is used to disable the feature.
The value manager (1) is used make the role as manager
for the dual network access redundant links.
The value client(2) is used make the role as client for
for the Dual network access redundant linksrw Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.88.1.1 |
snMspsDualNetAccessOperModeThe Operational mode for the Dual Network Access (DNA)Module.
The mode standalone (0) is used to disable the feature.
when the value is standalone, the port role for the dual network
access links are not controlled by this DNA Module.
If both admin and oper mode are manager, then the port role for
the dual network access links will be forwarding.
If both admin and oper mode are client, then the port role for
the dual network access links will be discarding or forwarding,
depending on reachability to the MRP Manager in the ring.
If oper mode state is mismatch for DNA admin mode manager, then
port state for DNA links will be discarding.
If oper mode state is mismatch for DNA admin mode client, then
port state for DNA links will be forwarding.
The oper state moves to mismatch in the following conditions,
a) if ring redundancy is disabled and admin mode for DNA is
manager or client.
b) if ring redundancy admin mode is not MRP Manager(Auto or Norm)
and DNA admin mode is manager
c) if ring redundancy admin mode is not MRP Client
and DNA admin mode is client
d) if ring redundancy oper mode (manager/client) is not matching
with DNA admin mode (manager/client).
The oper state for DNA moves out of mismatch state, When the
mismatch between ring redundancy and DNA are resolved.ro Enumeration .1.3.6.1.4.1.4329.20.1.1.1.1.88.1.2 |
snMspsDualNetAccessForwardLinksThe List of Dual Network Access links in the forwarding state and are controlled
by this DNA Module.ro PortList (Q-BRIDGE-MIB) .1.3.6.1.4.1.4329.20.1.1.1.1.88.1.3 |
snMspsDualNetAccessBlockedLinksThe List of Dual Network Access links in the discarding state and are controlled
by this DNA Module.ro PortList (Q-BRIDGE-MIB) .1.3.6.1.4.1.4329.20.1.1.1.1.88.1.4 |
snMspsModules OBJECT IDENTIFIER .1.3.6.1.4.1.4329.20.1.1.1.3 |
snMspsTc OBJECT IDENTIFIER .1.3.6.1.4.1.4329.20.1.1.1.3.1 |
snMspsDhcpClientDuidConfigStatusThis is used to identify duid values are auto generated or manually configured.
0x00
0x01
0x02
0x03
0x04
0x05
0x06
0x07
DEFVAL { 0 }
::= { snMspsDhcpClientDUID 5 }
snMspsDhcpClientOptTable OBJECT-TYPE
SYNTAX SEQUENCE OF SnMspsDhcpClientOptEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTIONrw INTEGER .snMspsDiagnosticsTemperatureEntry.46 |