SIAE-SFP-MIB
AI MIB Summary
The SIAE-SFP-MIB enables SNMP-based monitoring and alarm generation for SIAE Small Form-Factor Pluggable optical transceivers, exposing diagnostic parameters defined by SFF-8472 such as temperature, supply voltage, laser bias current, and optical transmit/receive power levels.
This MIB contains objects & alarms for a SFP (Small Form-Factor Pluggable) module. Reference documentation: 1) Small Form-factor Pluggable (SFP) Transceiver MultiSource Agreement (MSA) 2) Finisar's Application Note AN-2030, Rev. D. 3) SFF 8472 - Diagnostic Monitoring Interface for Optical Transceivers Rev 12.2 November 21, 2014 4) SFF 8024 - SFF Cross Reference to Industry Products Rev 4.0 June 27, 2016
Main OID:
sfp.1.3.6.1.4.1.3373.1103.74
54
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
54 total| Object Name |
|---|
sfpThis MIB contains objects & alarms for a SFP (Small Form-Factor Pluggable) module. Reference documentation: 1) Small Form-factor Pluggable (SFP) Transceiver MultiSource Agreement (MSA) 2) Finisar's Application Note AN-2030, Rev. D. 3) SFF 8472 - Diagnostic Monitoring Interface for Optical Transceivers Rev 12.2 November 21, 2014 4) SFF 8024 - SFF Cross Reference to Industry Products Rev 4.0 June 27, 2016 MODULE-IDENTITY .1.3.6.1.4.1.3373.1103.74 |
sfpMibVersionNumerical version of this module. The string version of this MIB have the following format: XX.YY.ZZ so, for example, the value 1 should be interpreted as 00.00.01 and the value 10001 should be interpreted as 01.00.01.ro INTEGER .1.3.6.1.4.1.3373.1103.74.1 |
sfpSerialIdTableEach SFP contains a 95+32 byte block of ID data fields. This table contains the items found in this data block. Fields in this data block is filled in by the SFP manufactor. The table shows the contents of this data block without further processing. SEQUENCE OF SfpSerialIdEntry .1.3.6.1.4.1.3373.1103.74.2 |
sfpSerialIdEntrySFP module record. SfpSerialIdEntry .1.3.6.1.4.1.3373.1103.74.2.1 |
sfpModuleIdThis index identifies a unique SFP module in the systemro Integer32 .1.3.6.1.4.1.3373.1103.74.2.1.1 |
sfpSerialIdValidWhen false the SFP data in this table is not valid. This will be set to False if the SFP module is not installed or if the EEPROM check code is wrong. The data in this table should not be used unless this element is True.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.3373.1103.74.2.1.2 |
sfpVendorNameThe SFP vendor name. Located at I2C address 0xa0, bytes: 20 - 35ro OCTET STRING .1.3.6.1.4.1.3373.1103.74.2.1.3 |
sfpVendorPartNumberThe SFP vendor part number. Located at I2C address 0xa0, bytes: 40 - 55ro OCTET STRING .1.3.6.1.4.1.3373.1103.74.2.1.4 |
sfpVendorRevThe SFP vendor's product revision number. Located at I2C address 0xa0, bytes: 56 - 59ro OCTET STRING .1.3.6.1.4.1.3373.1103.74.2.1.5 |
sfpVendorSNThe SFP vendor serial number. Located at I2C address 0xa0, bytes: 68 - 83ro OCTET STRING .1.3.6.1.4.1.3373.1103.74.2.1.6 |
sfpVendorDateCodeThe SFP vendor date code. Format: YYMMDDLL - YY: year, 00 = 2000 - MM: month, 01 = January - DD_ day, 01 to 31 - LL: vendor lot code, or blank. Located at I2C address 0xa0, bytes: 84 - 91ro OCTET STRING .1.3.6.1.4.1.3373.1103.74.2.1.7 |
sfpDiagMonitorCodeThis indicates which type of diagnostic monitoring is implemented (if any) in the SFP. -bit 7: = 0 legacy diagnostic implementations (should be 0) -bit 6: = 1 digital diagnostic monitoring implemented (should be 1) -bit 5: = 1 internal calibration -bit 4: = 1 external calibration mask -bit 3: = 0 OMA received power measurment, = 1 average received power -bit 2: = 1 I2C addressing option. Located at I2C address 0xa0, byte: 92ro Bits .1.3.6.1.4.1.3373.1103.74.2.1.8 |
sfpEnhancedOptionsCodeThis indicates which optional enhanced features are implemented (if any) in the SFP. Located at I2C address 0xa0, byte: 93ro Bits .1.3.6.1.4.1.3373.1103.74.2.1.9 |
sfpOptionsImplemented transceiver options: -bit 5: = 1 RATE_SELECT implemented. -bit 4: = 1 TX_DISABLE implemented -bit 3: = 1 TX_FAULT implemented -bit 2: = 1 LOS Implemented, inverted -bit 1: = 1 LOS Implemented Located at I2C address 0xa0, byte: 65ro Bits .1.3.6.1.4.1.3373.1103.74.2.1.10 |
sfpFibreChannelMediaFiber Channel transmission media. Located at I2C address 0xa0, byte: 9ro Bits .1.3.6.1.4.1.3373.1103.74.2.1.11 |
sfpComplianceElectronic or optical interfaces that are supported by the transceiver. Located at I2C address 0xa0, bytes: 4,5 & 6ro Bits .1.3.6.1.4.1.3373.1103.74.2.1.12 |
sfpWavelengthNominal transmiter output wavelength at room temperature. Units are in nm (nanometers). Located at I2C address 0xa0, bytes: 60 & 61 (endianess: big)ro Integer32 UNITS "nm" .1.3.6.1.4.1.3373.1103.74.2.1.13 |
sfpNominalBitRateNominal bit rate (in megabit per second) supported from this SFP module rouded to the nearest 100 megabits per second. Located at I2C address 0xa0, byte: 12ro Integer32 .1.3.6.1.4.1.3373.1103.74.2.1.14 |
sfpLinkLength9uLink length (in meters) supported from this SFP module while operating in compliance with the applicable standards using single mode fiber. A value of zero means that the transceiver does not support single mode fiber. Located at I2C address 0xa0, bytes: 14-15ro Integer32 UNITS "m" .1.3.6.1.4.1.3373.1103.74.2.1.15 |
sfpLinkLength50uLink length (in meters) supported from this SFP module while operating in compliance with the applicable standards using 50 micron multi-mode fiber. A value of zero means that the transceiver does not support 50 micron multi-mode mode fiber. Located at I2C address 0xa0, byte: 16ro Integer32 UNITS "m" .1.3.6.1.4.1.3373.1103.74.2.1.16 |
sfpLinkLength62u5Link length (in meters) supported from this SFP module while operating in compliance with the applicable standards using 62.5 micron multi-mode fiber. A value of zero means that the transceiver does not support 62.5 micron multi-mode mode fiber. Located at I2C address 0xa0, byte: 17ro Integer32 UNITS "m" .1.3.6.1.4.1.3373.1103.74.2.1.17 |
sfpLinkLengthCopperLink length (in meters) supported from this SFP module while operating in compliance with the applicable standards using copper cable. A value of zero means that the transceiver does not support copper cable. Located at I2C address 0xa0, byte: 18ro Integer32 UNITS "m" .1.3.6.1.4.1.3373.1103.74.2.1.18 |
sfpLabelThis is an ASCII string that identifies this SFP in the system.ro DisplayString .1.3.6.1.4.1.3373.1103.74.2.1.19 |
sfpFailAlarmSFP Module fail (module missing included)ro AlarmStatus (SIAE-ALARM-MIB) .1.3.6.1.4.1.3373.1103.74.2.1.20 |
sfpFailAlarmSeverityCodeDefines the severity associated to the sfpFailAlarm and enables/disables the trap generation on status change event.rw AlarmSeverityCode (SIAE-ALARM-MIB) .1.3.6.1.4.1.3373.1103.74.6 |
sfpDiagnosticTableEach SFP may contain a 256 byte block of diagnostic data fields. This table contains the items found in this data block. The data block is located at I2C address 0xa2. SEQUENCE OF SfpDiagnosticEntry .1.3.6.1.4.1.3373.1103.74.7 |
sfpDiagnosticEntryThis describes a row in the diagnostic table. SfpDiagnosticEntry .1.3.6.1.4.1.3373.1103.74.7.1 |
sfpDiagnosticValidif False, then the SFP data in this table is not valid. This will be set to False if the SFP module is not installed, or if the I/O card that contains the SFP is not installed or if the EEPROM check code is wrong. The data in the table should not be used unless this element is True.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.3373.1103.74.7.1.1 |
sfpLOSPinOutThis contains the T/F state of the SFP LOS (output) pin. It is True if the SFP has detected Loss-Of-Signal. located at I2c address 0xa2, address: 110, mask 0x02ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.3373.1103.74.7.1.2 |
sfpTxFaultPinOutThis contains the T/F state of the SFP Tx Fault (output) pin. It is True if the SFP has detected a Tx fault condition. located at I2C address 0xa2, Byte 110, mask 0x04ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.3373.1103.74.7.1.3 |
sfpRateSelectPinInThis contains the T/F state of the SFP RX Rate Select (input) pin. This function is not implemented on Finisar SFPs. located at I2C address 0xa2, Byte 110, mask 0x10ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.3373.1103.74.7.1.4 |
sfpTxDisablePinInThis contains the T/F state of the SFP TX Disable (input) pin. located at I2C address 0xa2, Byte 110, mask 0x80ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.3373.1103.74.7.1.5 |
sfpTemperatureThis contains the internal temperature of the SFP in tehnth of Celsius degrees. Range is from -128.0C to +128.0C, but is only valid from -40.0C to +125.0C with an accuracy of +/- 3C. Located at I2C address 0xa2, Bytes 96 & 97 (MSB, LSB)ro Temperature UNITS "C/10" .1.3.6.1.4.1.3373.1103.74.7.1.6 |
sfpVoltageThis contains the internally measured SFP supply voltage (Vcc). Units are in milliVolts (3210 = 3.21V). Range is 0 to 6.554V. Located at I2C address 0xa2, Bytes 98 & 99 (MSB, LSB)ro Integer32 .1.3.6.1.4.1.3373.1103.74.7.1.7 |
sfpTxBiasThis contains the internally measured SFP TX laser bias current. Units are in microAmps, and range from 0 to 131000uA (131mA). Located at I2C address 0xa2, Bytes 100 & 101 (MSB, LSB)ro Integer32 .1.3.6.1.4.1.3373.1103.74.7.1.8 |
sfpTxPowerThis contains the internally measured TX output power. Units are in uW (micro Watts), and range from 0 to 6554uW (6.535mW). This value is not valid if the transmitter is disabled. Located at I2C address 0xa2, Bytes 102 & 103 (MSB, LSB)ro Integer32 .1.3.6.1.4.1.3373.1103.74.7.1.9 |
sfpRxPowerThis contains the internally measured RX optical power. Units are in uW (micro Watts), and range from 0 to 6554uW (6.535mW). Located at I2C address 0xa2, Bytes 104 & 105 (MSB, LSB)ro Integer32 .1.3.6.1.4.1.3373.1103.74.7.1.10 |
sfpInternalAlarmsThis contains the state of the SFP internal alarm register. A bit is set for each alarm that is active. located at I2C address 0xa2, Byte 112 & 113 (MSB, LSB) mask 0xffc0ro Bits .1.3.6.1.4.1.3373.1103.74.7.1.11 |
sfpInternalWarningsThis contains the state of the SFP internal warning register. A bit is set for each warning that is active. located at I2C address 0xa2, Byte 116 & 117 (MSB, LSB) mask 0xffc0ro Bits .1.3.6.1.4.1.3373.1103.74.7.1.12 |
sfpAlarmTableThis table contains the SFP alarm and warning threshold values. SEQUENCE OF SfpAlarmEntry .1.3.6.1.4.1.3373.1103.74.10 |
sfpAlarmEntryAn entry into the Threshold table. SfpAlarmEntry .1.3.6.1.4.1.3373.1103.74.10.1 |
sfpPhysicalQuantityMeasured physical quantity. Units of temperature are tenth of Celsius degrres, units of Power supply voltage (Vcc) are microVolts, units of Tx laser bias current are microAmps (uA), units of Rx optical power are microWatts (uW), units of Tx output power are microWatts (uW).ro PhysicalQuantity .1.3.6.1.4.1.3373.1103.74.10.1.1 |
sfpThresholdHighAlarmA reading at or above this temperature will trigger a high measured physical quantity alarm.ro Integer32 .1.3.6.1.4.1.3373.1103.74.10.1.2 |
sfpThresholdHighWarningA reading at or above this temperature will trigger a high measured physical quantity warning.ro Integer32 .1.3.6.1.4.1.3373.1103.74.10.1.3 |
sfpThresholdLowAlarmA reading at or above this temperature will trigger a low measured physical quantity alarm.ro Integer32 .1.3.6.1.4.1.3373.1103.74.10.1.4 |
sfpThresholdLowWarningA reading at or above this temperature will trigger a low measured physical quantity warning.ro Integer32 .1.3.6.1.4.1.3373.1103.74.10.1.5 |
sfpHighAlarmMeasured physical quantity has crossed sfpThresholdHighAlarm.ro AlarmStatus (SIAE-ALARM-MIB) .1.3.6.1.4.1.3373.1103.74.10.1.6 |
sfpHighWarningAlarmMeasured physical quantity has crossed sfpThresholdHighWarning.ro AlarmStatus (SIAE-ALARM-MIB) .1.3.6.1.4.1.3373.1103.74.10.1.7 |
sfpLowAlarmMeasured physical quantity has crossed sfpThresholdLowAlarm.ro AlarmStatus (SIAE-ALARM-MIB) .1.3.6.1.4.1.3373.1103.74.10.1.8 |
sfpLowWarningAlarmMeasured physical quantity has crossed sfpThresholdLowWarning.ro AlarmStatus (SIAE-ALARM-MIB) .1.3.6.1.4.1.3373.1103.74.10.1.9 |
sfpHighAlarmSeverityCodeDefines the severity associated to the sfpHighAlarm and enables/disables the trap generation on status change event.rw AlarmSeverityCode (SIAE-ALARM-MIB) .1.3.6.1.4.1.3373.1103.74.11 |
sfpHighWarningAlarmSeverityCodeDefines the severity associated to the sfpHighWarningAlarm and enables/disables the trap generation on status change event.rw AlarmSeverityCode (SIAE-ALARM-MIB) .1.3.6.1.4.1.3373.1103.74.12 |
sfpLowAlarmSeverityCodeDefines the severity associated to the sfpLowAlarm and enables/disables the trap generation on status change event.rw AlarmSeverityCode (SIAE-ALARM-MIB) .1.3.6.1.4.1.3373.1103.74.13 |
sfpLowWarningAlarmSeverityCodeDefines the severity associated to the sfpLowWarningAlarm and enables/disables the trap generation on status change event.rw AlarmSeverityCode (SIAE-ALARM-MIB) .1.3.6.1.4.1.3373.1103.74.14 |