SIAE-MANOP-MIB
The SIAE-MANOP-MIB enables remote manual control of operational states and configuration parameters for SIAE network hardware, specifically facilitating the execution of administrative commands such as interface resets, service toggles, and system reboots. This module provides the necessary SNMP objects to trigger immediate, non-automated device actions that are not covered by standard polling or alarm mechanisms.
Imported Objects
Objects
14 total| Object Name |
|---|
manualOperationManual Operation management. MODULE-IDENTITY .1.3.6.1.4.1.3373.1103.71 |
manualOpTrap OBJECT IDENTIFIER .1.3.6.1.4.1.3373.1103.71.0 |
manualOpMibVersionNumerical version of this module. The string version of this MIB have the following format: XX.YY.ZZ so, for example, the value 1 should be interpreted as 00.00.01 and the value 10001 should be interpreted as 01.00.01.ro INTEGER .1.3.6.1.4.1.3373.1103.71.1 |
manualOpTableTable with manual operation record. SEQUENCE OF ManualOpRecord .1.3.6.1.4.1.3373.1103.71.2 |
manualOpRecordManual operation record. ManualOpRecord .1.3.6.1.4.1.3373.1103.71.2.1 |
manualOpIdManual operation index.ro Integer32 .1.3.6.1.4.1.3373.1103.71.2.1.1 |
manualOpObjectIdObject identifier of the manual operation active element.ro OBJECT IDENTIFIER .1.3.6.1.4.1.3373.1103.71.2.1.2 |
manualOpEventTimeThe time (in seconds since 01-Gen-1970) when the event was registered in the table.ro Unsigned32 .1.3.6.1.4.1.3373.1103.71.2.1.3 |
manualOpValueTypeThe type of the value. One and only one of the value object that follow is used for a given row in this table, based on this type.ro Enumeration .1.3.6.1.4.1.3373.1103.71.2.1.4 |
manualOpIntegerValThe value when manualOpValueType is 'integer32'.ro Integer32 .1.3.6.1.4.1.3373.1103.71.2.1.5 |
manualOpOidValThe value when manualOpValueType is 'objectId'.ro OBJECT IDENTIFIER .1.3.6.1.4.1.3373.1103.71.2.1.6 |
manualOpActiveManual Operation active on the equipment.ro AlarmStatus (SIAE-ALARM-MIB) .1.3.6.1.4.1.3373.1103.71.3 |
manualOpActiveSeverityCodeDefines the severity associated to manualOpActive and enables/disables the trap generation on status change event.rw AlarmSeverityCode (SIAE-ALARM-MIB) .1.3.6.1.4.1.3373.1103.71.4 |
manualOpTimeOutThis object defines the time (in seconds) after wich the manual operations are cleared. The maximum value is equivalent to 48 hours. A zero means no Time-out.rw INTEGER .1.3.6.1.4.1.3373.1103.71.5 |
More MIBs from SIAE MICROELETTRONICA spa
Browse all SIAE MICROELETTRONICA spaMIBs →The SIAE-RADIO-SYSTEM-MIB facilitates the monitoring and management of SIAE radio transmission infrastructure, specifically exposing performance metrics such as RF link status, signal strength, error rates, and system health indicators for broadcast and telecommunications equipment.
The SIAE-PTP-MIB module enables monitoring and management of SIAE hardware devices implementing the IEEE 1588-2008 Precision Time Protocol and ITU-T G.8275.1 telecom profile, specifically exposing metrics for clock synchronization states, grandmaster selection, and phase/time offset measurements.
The SIAE-SYNC-MIB module manages timing source configuration and synchronization states for SIAE broadcast infrastructure equipment, monitoring critical metrics such as reference clock status, synchronization lock status, and time deviation values to ensure precise frame and data alignment.
The SIAE-ALARM-MIB module enables the monitoring of network element alarm state transitions and the retrieval of active alarm entries via SNMP for SIAE-managed infrastructure. It specifically tracks alarm severity, timestamp, and status changes to facilitate real-time fault detection and event logging.
The SIAE-SFP-MIB enables SNMP-based monitoring and alarm generation for SIAE Small Form-Factor Pluggable optical transceivers, exposing diagnostic parameters defined by SFF-8472 such as temperature, supply voltage, laser bias current, and optical transmit/receive power levels.
The SIAE-PMRXPWR-MIB module enables SNMP-based monitoring of received RF power levels within SIAE microwave radio systems, specifically tracking performance metrics such as instantaneous and average RX signal strength to assess link quality and detect signal degradation.