REDLINE-AN80I-IF-MIB
AI MIB Summary
The REDLINE-AN80I-IF-MIB provides SNMP object definitions for monitoring interface-level statistics, link states, and operational parameters specific to the Redline AN80i hardware module. This module enables granular visibility into the physical and data-link layer performance of the AN80i device within a managed network infrastructure.
This MIB module contains object definitions applicable only to Redline AN80i module.
Main OID:
redlineAn80iIfMib.1.3.6.1.4.1.10728.2.10.2
110
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
110 total| Object Name |
|---|
redlineAn80iIfMibThis MIB module contains object definitions applicable only to Redline AN80i module. MODULE-IDENTITY .1.3.6.1.4.1.10728.2.10.2 |
redlineAn80iIfTrapDefinitions OBJECT IDENTIFIER .1.3.6.1.4.1.10728.2.10.2.0 |
an80iIfRegistrationFailedTrapEvent that reports the failure of a registration attempt of a SS that is not defined in the link table. NOTIFICATION-TYPE .1.3.6.1.4.1.10728.2.10.2.0.1 |
an80iIfRegistrationOKTrapAn event to report the successful SS registration. NOTIFICATION-TYPE .1.3.6.1.4.1.10728.2.10.2.0.2 |
redlineAn80iIfPtpObjects OBJECT IDENTIFIER .1.3.6.1.4.1.10728.2.10.2.1 |
redlineAn80iIfPtpLinkConfig OBJECT IDENTIFIER .1.3.6.1.4.1.10728.2.10.2.1.1 |
an80iIfEncryptionControlSpecifies if encryption type.rw Enumeration .1.3.6.1.4.1.10728.2.10.2.1.1.1 |
an80iIfModReductionApplies when the adaptive rate is disabled, and specifies how many levels the system must drop in modulation before beginning retransmission to address packet errors.rw INTEGER (0 .. 7) .1.3.6.1.4.1.10728.2.10.2.1.1.2 |
an80iIfAdaptiveModIf enabled, the system automatically adjust the modulation to obtain the maximum throughput.rw Enumeration .1.3.6.1.4.1.10728.2.10.2.1.1.3 |
an80iIfUncodedBurstRateThe maximum index of the link uncoded burst rate. The rate also depends on the channel width. The possible values are 0..7.rw INTEGER .1.3.6.1.4.1.10728.2.10.2.1.1.4 |
an80iIfEncryptionKeyThe Encryption Key used for the AN-80i. Enter the MAC address of the peer equipment to enable over-the-air data encryption.rw OCTET STRING .1.3.6.1.4.1.10728.2.10.2.1.1.5 |
an80iIfPacketRetransControlEnables/disables packet retransmission. The retransmission scheme is based on the Acknowledge /Request (ARQ) algorithm that detects when packets are lost and makes a request to the MAC scheduler to repeat transmission of the lost packets.rw Enumeration .1.3.6.1.4.1.10728.2.10.2.1.1.6 |
an80iIfLinkLenModeIn manual mode the system uses the user-supplied value for link length. In the auto mode the system calculate itself the distance, which can be read using 'calculated distance'.rw Enumeration .1.3.6.1.4.1.10728.2.10.2.1.1.7 |
an80iIfLinkLengthUser supplied PTP Link Length [Km].rw Integer32 UNITS "Km" .1.3.6.1.4.1.10728.2.10.2.1.1.8 |
an80iIfCalcLinkDstThe calculated link distance [Km].ro Integer32 UNITS "Km" .1.3.6.1.4.1.10728.2.10.2.1.1.9 |
an80iIfLinkNameLink Name.rw DisplayString .1.3.6.1.4.1.10728.2.10.2.1.1.10 |
redlineAn80iIfPtpLinkStats OBJECT IDENTIFIER .1.3.6.1.4.1.10728.2.10.2.1.2 |
an80iIfCurrUncodedBurstRateIndicates the index of the link uncoded burst rate. With adaptive modulation enabled, this rate may change over time.ro Unsigned32 UNITS "" .1.3.6.1.4.1.10728.2.10.2.1.2.1 |
an80iIfPtpLinkStatusIndicates if the link has been established/not established.ro Enumeration .1.3.6.1.4.1.10728.2.10.2.1.2.2 |
an80iIfRxPacketsIndicates the number of received wireless packets with a correct CRC.ro Counter64 .1.3.6.1.4.1.10728.2.10.2.1.2.3 |
an80iIfRxPacketsReTxIndicates the number of received retransmitted wireless packets with a correct CRC.ro Counter64 .1.3.6.1.4.1.10728.2.10.2.1.2.4 |
an80iIfRxPacketsDiscIndicates the number of received retransmitted wireless packets with bad CRC.ro Counter64 .1.3.6.1.4.1.10728.2.10.2.1.2.5 |
an80iIfTxPacketsIndicates the number of transmitted packets that were received correctly by the other equipment.ro Counter64 .1.3.6.1.4.1.10728.2.10.2.1.2.6 |
an80iIfTxPacketsReTxIndicates the number of retransmitted wireless packets received correctly by the other equipment.ro Counter64 .1.3.6.1.4.1.10728.2.10.2.1.2.7 |
an80iIfTxPacketsDiscIndicates the number of retransmitted wireless packets that were not received correctly by the other equipmentro Counter64 .1.3.6.1.4.1.10728.2.10.2.1.2.8 |
an80iIfRssiMinIndicates the minimum received signal strength for the measuring interval.ro Integer32 .1.3.6.1.4.1.10728.2.10.2.1.2.9 |
an80iIfRssiMeanIndicates the average received signal strength for the measuring interval.ro Integer32 .1.3.6.1.4.1.10728.2.10.2.1.2.10 |
an80iIfRssiMaxIndicates the maximum received signal strength for the measuring interval.ro Integer32 .1.3.6.1.4.1.10728.2.10.2.1.2.11 |
an80iIfAvrSinAdrIndicates the Signal to interference, noise and distortion ratio.ro Integer32 .1.3.6.1.4.1.10728.2.10.2.1.2.12 |
redlineAn80iIfPmpObjects OBJECT IDENTIFIER .1.3.6.1.4.1.10728.2.10.2.2 |
redlineAn80iIfPmpSsObjects OBJECT IDENTIFIER .1.3.6.1.4.1.10728.2.10.2.2.1 |
an80iIfLastMissedMacAddressMAC address for the last SS that attempted to register but it was not present in the 'Links' tablero MacAddress (SNMPv2-TC) .1.3.6.1.4.1.10728.2.10.2.2.1.1 |
an80iIfLastRegistMacAddressMAC address for the last SS that successfuly registeredro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.10728.2.10.2.2.1.2 |
an80iIfDenyMacAddressMAC address for the SS that will be denied by this SCrw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.10728.2.10.2.2.1.3 |
an80iIfLastRegistLinkIdThe link ID for the last SS that successfully registeredro INTEGER .1.3.6.1.4.1.10728.2.10.2.2.1.4 |
an80iIfPmpLinkConfigTableThis table contains the PMP link configuration information. SEQUENCE OF An80iIfPmpLinkConfigEntry .1.3.6.1.4.1.10728.2.10.2.2.2 |
an80iIfPmpLinkConfigEntryThis table provides one row for each PMP link that has been configured in the SC. An80iIfPmpLinkConfigEntry .1.3.6.1.4.1.10728.2.10.2.2.2.1 |
an80iIfPmpLinkIdThe PMP Link Identifier. INTEGER .1.3.6.1.4.1.10728.2.10.2.2.2.1.1 |
an80iIfPmpLinkNameThe PMP Link Name.rw DisplayString .1.3.6.1.4.1.10728.2.10.2.2.2.1.2 |
an80iIfPmpLinkPeerMacAddressThe MAC address for the peer SSrw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.10728.2.10.2.2.2.1.3 |
an80iIfPmpLinkULBurstRateUser supplied index of the uplink uncoded burst rate.rw Unsigned32 UNITS "" .1.3.6.1.4.1.10728.2.10.2.2.2.1.4 |
an80iIfPmpLinkDLBurstRateUser supplied index of the downlink uncoded burst rate.rw Unsigned32 UNITS "" .1.3.6.1.4.1.10728.2.10.2.2.2.1.5 |
an80iIfPmpLinkConfigStatusThis object is used to create a new row or modify or delete an existing row in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.10728.2.10.2.2.2.1.6 |
an80iIfPmpLinkStatsTableThis table contains the PMP link statistics information. SEQUENCE OF An80iIfPmpLinkStatsEntry .1.3.6.1.4.1.10728.2.10.2.2.3 |
an80iIfPmpLinkStatsEntryThis table provides one row for each PMP link that has been configured in the Service Controller. An80iIfPmpLinkStatsEntry .1.3.6.1.4.1.10728.2.10.2.2.3.1 |
an80iIfPmpLinkStatusIndicates if the link has been established/not established.ro Enumeration .1.3.6.1.4.1.10728.2.10.2.2.3.1.1 |
an80iIfPmpLinkStatusCodeIndicates the error code for the link.ro Integer32 .1.3.6.1.4.1.10728.2.10.2.2.3.1.2 |
an80iIfRegPmpLinkConnsIndicates the registered connections for this Link.ro Integer32 .1.3.6.1.4.1.10728.2.10.2.2.3.1.3 |
an80iIfPmpLinkUpTimeThe time (in hundredths of a second) elapsed since the link was established (up) last time.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.10728.2.10.2.2.3.1.4 |
an80iIfPmpLinkLostCountNumber of times the link has been lost since the system started.ro Counter32 .1.3.6.1.4.1.10728.2.10.2.2.3.1.5 |
an80iIfPmpLinkCurrDLUncBurstRateIndicates the index of the link's downlink actual uncoded burst rate.ro Unsigned32 UNITS "" .1.3.6.1.4.1.10728.2.10.2.2.3.1.6 |
an80iIfPmpLinkDLRssiIndicates the link's DL RSSI (Received Signal Strength Indicator).ro Integer32 .1.3.6.1.4.1.10728.2.10.2.2.3.1.7 |
an80iIfPmpLinkDLSinAdrIndicates the link's DL SINADR (Signal Interference and Noise Distorsion Ratio).ro Integer32 .1.3.6.1.4.1.10728.2.10.2.2.3.1.8 |
an80iIfPmpLinkDLLostFrmIndicates the link's DL lost frames.ro Counter64 .1.3.6.1.4.1.10728.2.10.2.2.3.1.9 |
an80iIfPmpLinkDLBlksTotIndicates the link's DL blocks transmitted.ro Counter64 .1.3.6.1.4.1.10728.2.10.2.2.3.1.10 |
an80iIfPmpLinkDLBlksRetrIndicates the link's DL block re-transmitted.ro Counter64 .1.3.6.1.4.1.10728.2.10.2.2.3.1.11 |
an80iIfPmpLinkDLBlksDiscIndicates the link's DL blocks lostro Counter64 .1.3.6.1.4.1.10728.2.10.2.2.3.1.12 |
an80iIfPmpLinkCurrULUncBurstRateIndicates the index of the link's uplink actual uncoded burst rate.ro Unsigned32 UNITS "Mb/s" .1.3.6.1.4.1.10728.2.10.2.2.3.1.13 |
an80iIfPmpLinkULRssiIndicates the link's UL RSSI (Received Signal Strength Indicator).ro Integer32 .1.3.6.1.4.1.10728.2.10.2.2.3.1.14 |
an80iIfPmpLinkULSinAdrIndicates the link's UL SINADR (Signal Interference and Noise Distorsion Ratio).ro Integer32 .1.3.6.1.4.1.10728.2.10.2.2.3.1.15 |
an80iIfPmpLinkULLostFrmIndicates the link's UL lost frames.ro Counter64 .1.3.6.1.4.1.10728.2.10.2.2.3.1.16 |
an80iIfPmpLinkULBlksTotIndicates the link's UL blocks transmitted.ro Counter64 .1.3.6.1.4.1.10728.2.10.2.2.3.1.17 |
an80iIfPmpLinkULBlksRetrIndicates the link's UL block re-transmitted.ro Counter64 .1.3.6.1.4.1.10728.2.10.2.2.3.1.18 |
an80iIfPmpLinkULBlksDiscIndicates the link's UL blocks lostro Counter64 .1.3.6.1.4.1.10728.2.10.2.2.3.1.19 |
an80iIfPmpLinkStatsStatusThis object is used to create a new row or modify or delete an existing row in this table.ro RowStatus (SNMPv2-TC) .1.3.6.1.4.1.10728.2.10.2.2.3.1.20 |
an80iIfPmpGroupConfigTableThis table contains group configuration information. The group defined as a broadcast domain. SEQUENCE OF An80iIfPmpGroupConfigEntry .1.3.6.1.4.1.10728.2.10.2.2.4 |
an80iIfPmpGroupConfigEntryThis table provides one row for each group defined in the Service Controller An80iIfPmpGroupConfigEntry .1.3.6.1.4.1.10728.2.10.2.2.4.1 |
an80iIfPmpGroupIdThe PMP Group Identifier. INTEGER .1.3.6.1.4.1.10728.2.10.2.2.4.1.1 |
an80iIfPmpGroupNameThe PMP Group Name.rw DisplayString .1.3.6.1.4.1.10728.2.10.2.2.4.1.2 |
an80iIfPmpGroupTaggingControlSpecifies tagging mode.Only one pass-through group can exist. This is the default group. In the pass-through mode all the Ethernet packets that do not have a VLAN tag or an undefined VID will be classified in this group.rw Enumeration .1.3.6.1.4.1.10728.2.10.2.2.4.1.3 |
an80iIfPmpGroupVlanIdIn the tagged mode all Ethernet packets that have this VID will be classified to belong to this group.rw INTEGER .1.3.6.1.4.1.10728.2.10.2.2.4.1.4 |
an80iIfPmpGroupDefPriorityThis field is used every time a tag is added at the exit point. The priority will be the one specified at the entry point.rw INTEGER .1.3.6.1.4.1.10728.2.10.2.2.4.1.5 |
an80iIfPmpGroupSCEtherControlMakes the Sector Controller a member of the group.rw Enumeration .1.3.6.1.4.1.10728.2.10.2.2.4.1.6 |
an80iIfPmpGroupQosLevelQoS level (index) that will affect the bandwidth and the delay for this group.rw INTEGER .1.3.6.1.4.1.10728.2.10.2.2.4.1.7 |
an80iIfPmpGroupConfigStatusThis object is used to create a new row or modify or delete an existing row in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.10728.2.10.2.2.4.1.8 |
an80iIfPmpGroupRateDefine the index of the group rate. (0..7, 8=auto)rw INTEGER .1.3.6.1.4.1.10728.2.10.2.2.4.1.9 |
an80iIfPmpGroupSStoSSMulticastEnable the Subscriber to subscriber multicast traffic.rw Enumeration .1.3.6.1.4.1.10728.2.10.2.2.4.1.10 |
an80iIfPmpGroupStatsTableThis table contains group statistics information. The group defined as a broadcast domain. SEQUENCE OF An80iIfPmpGroupStatsEntry .1.3.6.1.4.1.10728.2.10.2.2.5 |
an80iIfPmpGroupStatsEntryThis table provides one row for each group defined in the Service Controller An80iIfPmpGroupStatsEntry .1.3.6.1.4.1.10728.2.10.2.2.5.1 |
an80iIfPmpGroupPacketsTxBroadcast/multicast Ethernet packets classified and transmitted to the group.ro Counter64 .1.3.6.1.4.1.10728.2.10.2.2.5.1.1 |
an80iIfPmpGroupPacketDiscEthernet packets classified to be sent to the group but discarded due to unavailable memory.ro Counter64 .1.3.6.1.4.1.10728.2.10.2.2.5.1.2 |
an80iIfPmpGroupStatsStatusThis object is used to create a new row or modify or delete an existing row in this table.ro RowStatus (SNMPv2-TC) .1.3.6.1.4.1.10728.2.10.2.2.5.1.3 |
an80iIfPmpConnConfigTableThis table contains connections configuration information. One connection defines the transport parameter for Ethernet packets that have specific properties. SEQUENCE OF An80iIfPmpConnConfigEntry .1.3.6.1.4.1.10728.2.10.2.2.6 |
an80iIfPmpConnConfigEntryThis table provides one row for each connection defined in the Service Controller An80iIfPmpConnConfigEntry .1.3.6.1.4.1.10728.2.10.2.2.6.1 |
an80iIfPmpConnIdThe PMP Conn Identifier. INTEGER .1.3.6.1.4.1.10728.2.10.2.2.6.1.1 |
an80iIfPmpConnNameThe PMP Conn Name.rw DisplayString .1.3.6.1.4.1.10728.2.10.2.2.6.1.2 |
an80iIfPmpConnTaggingControlSpecifies tagging mode. Only one pass-through connection can be defined on each link. This is the default connection. All the untagged packets or with a VID that is not defined will be transmitted on this connection.rw Enumeration .1.3.6.1.4.1.10728.2.10.2.2.6.1.3 |
an80iIfPmpConnVlanIdSpecifies VLAN Id for the tagged mode.rw INTEGER .1.3.6.1.4.1.10728.2.10.2.2.6.1.4 |
an80iIfPmpConnDefPriorityThis field is used every time a tag is added at the exit point. The priority will be the one specified at the entry point.rw INTEGER .1.3.6.1.4.1.10728.2.10.2.2.6.1.5 |
an80iIfPmpConnDefParentLinkThis object specifies the parent link of the connection.rw INTEGER .1.3.6.1.4.1.10728.2.10.2.2.6.1.6 |
an80iIfPmpConnDefParenGroupThis object specifies the parent group of the connection.rw INTEGER .1.3.6.1.4.1.10728.2.10.2.2.6.1.7 |
an80iIfPmpConnDLQosConnection QoS level (index) that will affect the DL bandwidth and the delay.rw INTEGER .1.3.6.1.4.1.10728.2.10.2.2.6.1.8 |
an80iIfPmpConnULQosConnection QoS level (index) that will affect the UL bandwidth and the delay.rw INTEGER .1.3.6.1.4.1.10728.2.10.2.2.6.1.9 |
an80iIfPmpConnConfigStatusThis object is used to create a new row or modify or delete an existing row in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.10728.2.10.2.2.6.1.10 |
an80iIfPmpConnStatsTableThis table contains connections configuration information. One connection defines the transport parameter for Ethernet packets that have specific properties. SEQUENCE OF An80iIfPmpConnStatsEntry .1.3.6.1.4.1.10728.2.10.2.2.7 |
an80iIfPmpConnStatsEntryThis table provides one row for each connection defined in the Service Controller An80iIfPmpConnStatsEntry .1.3.6.1.4.1.10728.2.10.2.2.7.1 |
an80iIfPmpConnDLPacketsTxIndicates Ethernet packets sent by SC.ro Counter64 .1.3.6.1.4.1.10728.2.10.2.2.7.1.1 |
an80iIfPmpConnDLPacketsRxIndicates Ethernet packets receivedby SS.ro Counter64 .1.3.6.1.4.1.10728.2.10.2.2.7.1.2 |
an80iIfPmpConnDLPacketsDiscIndicates packets discarded due to full buffer.ro Counter64 .1.3.6.1.4.1.10728.2.10.2.2.7.1.3 |
an80iIfPmpConnULPacketsTxIndicates Ethernet packets sent by SS.ro Counter64 .1.3.6.1.4.1.10728.2.10.2.2.7.1.4 |
an80iIfPmpConnULPacketsRxIndicates Ethernet packets received SC.ro Counter64 .1.3.6.1.4.1.10728.2.10.2.2.7.1.5 |
an80iIfPmpConnULPacketsDiscIndicates packets discarded due to full buffer.ro Counter64 .1.3.6.1.4.1.10728.2.10.2.2.7.1.6 |
an80iIfPmpConnStatsStatusThis object is used to create a new row or modify or delete an existing row in this table.ro RowStatus (SNMPv2-TC) .1.3.6.1.4.1.10728.2.10.2.2.7.1.7 |
redlineAn80iIfConformance OBJECT IDENTIFIER .1.3.6.1.4.1.10728.2.10.2.4 |
redlineAn80iIfGroups OBJECT IDENTIFIER .1.3.6.1.4.1.10728.2.10.2.4.1 |
redlineAn80iIfPtpGroupPoint to point link objects. Unknown .1.3.6.1.4.1.10728.2.10.2.4.1.1 |
redlineAn80iIfPmpGroupPoint to multipoint link objects. Unknown .1.3.6.1.4.1.10728.2.10.2.4.1.2 |
redlineAn80iIfNotificationGroupThe notifications which indicate specific events within the AN80i interface. Unknown .1.3.6.1.4.1.10728.2.10.2.4.1.3 |
redlineAn80iIfCompls OBJECT IDENTIFIER .1.3.6.1.4.1.10728.2.10.2.4.2 |
redlineAn80iIfComplianceThe compliance statement for SNMP entities that implement this MIB module. Unknown .1.3.6.1.4.1.10728.2.10.2.4.2.1 |