REDLINE-AN50-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for REDLINE-AN50-MIB.
115
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
115 total| Object Name |
|---|
redline OBJECT IDENTIFIER .1.3.6.1.4.1.10728 |
RFC1155-SMI Unknown .1.3.6.1.4.1.10728 |
an50TftpFailTrapAn event to report the failure of a Software Download. TRAP-TYPE .1.3.6.1.4.1.10728.0.1 |
an50TftpSuccessTrapAn event to report the success of a Software Download. TRAP-TYPE .1.3.6.1.4.1.10728.0.2 |
an50PswdChangeFailTrapAn event to report the failure of a password change. TRAP-TYPE .1.3.6.1.4.1.10728.0.3 |
an50FirmwareConfigFailTrapAn event to report the failure of a firmware config. TRAP-TYPE .1.3.6.1.4.1.10728.0.4 |
an50EepromCorruptedTrapAn event to report the corruption of the EEPROM. TRAP-TYPE .1.3.6.1.4.1.10728.0.5 |
an50PowerSupplyFailureTrapAn event to report the power supply failure. TRAP-TYPE .1.3.6.1.4.1.10728.0.6 |
an50SaveConfigTrapAn event to report the saving of configuration TRAP-TYPE .1.3.6.1.4.1.10728.0.7 |
an50ModifiedIDTrapAn event to report the modification in the configuration of a CID TRAP-TYPE .1.3.6.1.4.1.10728.0.8 |
an50pmpRegistrationMissedAn event to report the missing of the registration by a AN50
Subscriber to one BS.This trap is sent by the BS and contains
the MAC address of the SS missing the registration TRAP-TYPE .1.3.6.1.4.1.10728.0.9 |
an50pmpRegistrationSuccessfulAn event to report the successful registration of an AN50
Subscriber to BS. This trap is sent by the BS and contains
the MAC address of the newly registered SS TRAP-TYPE .1.3.6.1.4.1.10728.0.10 |
an50DFSEventAn event to report a dynamic frequency selection (DFS) event in AN50 TRAP-TYPE .1.3.6.1.4.1.10728.0.11 |
redlineProducts OBJECT IDENTIFIER .1.3.6.1.4.1.10728.1 |
redlineMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.10728.2 |
redlineAn50 OBJECT IDENTIFIER .1.3.6.1.4.1.10728.2.16 |
an50General OBJECT IDENTIFIER .1.3.6.1.4.1.10728.2.16.1 |
an50GenUBRIndicates the system's current uncoded burst rate. With
adaptive modulation enabled, this rate may change over time,
depending on the prevailing propagation conditions.ro INTEGER .1.3.6.1.4.1.10728.2.16.1.1 |
an50GenRFLinkconnected(2) indicates the terminal is communicating
properly to the remote terminal.
notConnected(1) indicates there is no communication with
the remote terminal.ro Enumeration .1.3.6.1.4.1.10728.2.16.1.2 |
an50GenFrequencyThe frequency which represents the operating channel of the link.
The system can be configured to operate over 9 distinct channels.rw INTEGER .1.3.6.1.4.1.10728.2.16.1.3 |
an50GenAllignmentModeSpecifies if the antenna alignment is done with buzzer or voltage.rw Enumeration .1.3.6.1.4.1.10728.2.16.1.4 |
an50GenEncryptionEnabledSpecifies if encryption is enabled or not.rw Enumeration .1.3.6.1.4.1.10728.2.16.1.5 |
an50GenFlowControlEnabledThis attribute specifies if flow control is enabled or not.rw Enumeration .1.3.6.1.4.1.10728.2.16.1.6 |
an50GenHttpAccessEnabledThis attribute specifies if Http Access is enabled or not.rw Enumeration .1.3.6.1.4.1.10728.2.16.1.7 |
an50GenTelnetAccessEnabledThis attribute specifies if Telnet Access is enabled or not.rw Enumeration .1.3.6.1.4.1.10728.2.16.1.8 |
an50GenTelnetPortThis attribute specifies the Telnet port number.rw INTEGER .1.3.6.1.4.1.10728.2.16.1.9 |
an50GenOptionsKeyThis attribute specifies the Product Options Key.rw OCTET STRING .1.3.6.1.4.1.10728.2.16.1.10 |
an50GenResetDevicereset(2) indicates to reset the AN50 terminal.
donothing(1) indicates do not reset AN50 terminal.rw Enumeration .1.3.6.1.4.1.10728.2.16.1.11 |
an50GenFaultThe attribute specifies the Fault LED status of the terminal.ro Enumeration .1.3.6.1.4.1.10728.2.16.1.12 |
an50GenTxPowerThis object specifies the actual Tx Power of the AN-50 Node in ?ro INTEGER (-20 .. 20) .1.3.6.1.4.1.10728.2.16.1.13 |
an50GenRegisteredStationsThis object specifies the actual number of configured links.ro INTEGER .1.3.6.1.4.1.10728.2.16.1.14 |
an50GenRegisteredConnectionsThis object specifies the actual number of configured connections.ro INTEGER .1.3.6.1.4.1.10728.2.16.1.15 |
an50GenActiveWirelessLinksThis object specifies the actual number of provisioned links.ro INTEGER .1.3.6.1.4.1.10728.2.16.1.16 |
an50GenChannelAutoScanThis object specifies the Auto-Scanning feature for the channel.rw Enumeration .1.3.6.1.4.1.10728.2.16.1.17 |
an50GenIduTypeThis object specifies the Indoor Unit Type.ro INTEGER .1.3.6.1.4.1.10728.2.16.1.18 |
an50GenOduTypeThis object specifies the Outdoor Unit Type.ro INTEGER .1.3.6.1.4.1.10728.2.16.1.19 |
an50Config OBJECT IDENTIFIER .1.3.6.1.4.1.10728.2.16.2 |
an50ConfigEther OBJECT IDENTIFIER .1.3.6.1.4.1.10728.2.16.2.1 |
an50EtherMacAddressThis object specifies the Ethernet MAC address of the local terminal.ro OCTET STRING .1.3.6.1.4.1.10728.2.16.2.1.1 |
an50EtherGatewayThe IP Gateway of the AN-50 This field is used to specify
the IP address of the gateway which
the AN-50 is communicating through the core network.rw IpAddress .1.3.6.1.4.1.10728.2.16.2.1.2 |
an50EtherPortStatusThe attribute specifies the status of the Ethernet Port of the AN50.ro Enumeration .1.3.6.1.4.1.10728.2.16.2.1.3 |
an50EtherIPThe IP address of the AN-50. The default address from the factory
is 192.168.25.2. For the initial set-up, the terminal should not
be connected to the Internet network, i.e. the host computer should
be connected directly to the terminal Ethernet port, to avoid address
conflicts with other devices in a public network. Once the IP address
has been set, the terminal can be connected to the core network,
where it can receive either static or dynamic addressing (DHCP)
in future configuration updates.rw IpAddress .1.3.6.1.4.1.10728.2.16.2.1.4 |
an50EtherMaskThe IP Subnet Mask of the AN-50. The value is typically set
to 255.255.255.0 (Class C subnet), which prevents certain
local devices from going out into the wireless network.rw IpAddress .1.3.6.1.4.1.10728.2.16.2.1.5 |
an50Ether100This object specifies the 100 Mb/s Ethernet LED status of the AN50.ro Enumeration .1.3.6.1.4.1.10728.2.16.2.1.6 |
an50EtherFdThe object specifies the Ethernet FullDuplex LED status of the AN50.ro Enumeration .1.3.6.1.4.1.10728.2.16.2.1.7 |
an50EtherMgmVidEnThe attribute specifies the Ethernet Management Vlan Enabled Status of the AN50.rw Enumeration .1.3.6.1.4.1.10728.2.16.2.1.8 |
an50EtherMgmVidThe attribute specifies the Ethernet Management Vlan Id of the AN50.rw INTEGER ( 0..4095 ) .1.3.6.1.4.1.10728.2.16.2.1.9 |
an50EtherLbenThe attribute specifies the Link Backup Enable Status of the AN50.rw Enumeration .1.3.6.1.4.1.10728.2.16.2.1.10 |
an50ConfigWireless OBJECT IDENTIFIER .1.3.6.1.4.1.10728.2.16.2.2 |
an50WrlsChannelspecifies the operating channel of the system,
within the 100 MHz available in the 5.8GHz UNII band.
To avoid interference, two PTP links operating in
the same physical location (co-located) or within close
proximity (e.g. across the street) must be separated by at
least one channel, i.e. the gap between channels should
be 20 MHz or more (e.g. channels 1 and 3).rw Enumeration .1.3.6.1.4.1.10728.2.16.2.2.1 |
an50WrlsTxPowerThe Tx Power of the AN-50 in dBm. Specifies the power level of the system,
which is preset at the factory and should not be altered. In the event
that this parameter needs to be changed, please contact the
Redline support team.rw INTEGER (-20 .. 20) .1.3.6.1.4.1.10728.2.16.2.2.2 |
an50WrlsModReductionThe Modulation Reduction Level of the AN-50. Applies when the
Adaptive rate is disabled. Specifies how many levels the system
must drop in modulation before beginning re-transmission to address
packet errors.
The value can be set from 1-7, with 2 being the typical value.rw INTEGER .1.3.6.1.4.1.10728.2.16.2.2.3 |
an50WrlsAdaptiveModSetting this attribute to AdaptiveRate(2) sets the system
to operate in adaptive modulation mode. It is recommended
to keep the AN-50 in this mode so that the system can
automatically adjust the modulation level to the highest possible
data rate based on measured RF performance. The user
can define the minimum desired modulation level by setting the
Main rate parameter.
If the system meets this data rate, then the Signal LED on the front
panel will light continuously green. If packet errors exceed
one out of a million, the system will automatically lower the modulation
level to maintain the link. In this case, the LED will flash green.
If errors continue when the system reaches the lowest modulation level,
the LED will flash red to indicate a failed RF link.
The user can also disable the dynamic modulation mode by disabling
Adaptive Modulation. In this mode, the user is required to set the
Burst Rate and the Modulation Reduction Level. It is recommended not
to operate the system in manual mode, as this mode is intended primarily
for field support.
Note the Signal LED will light solid green when the packet error rate is
less than 1 out of a million. When the errors exceed this limit, the LED
will not illuminate, indicating the RF link has failed.rw Enumeration .1.3.6.1.4.1.10728.2.16.2.2.4 |
an50WrlsUBRThis object contains the desired net uncoded burst rate for the link.
Set uncoded burst rate in steps (0=6Mb/s, 1=9Mb/s, 2=12Mb/s,
3=18Mb/s, 4=24Mb/s, 5=36Mb/s, 6=48Mb/s, 7=54Mbs).rw INTEGER .1.3.6.1.4.1.10728.2.16.2.2.5 |
an50WrlsMasterThe object contains the configured mode of the AN50 terminal.
1 = PTP Slave, 2 = PTP Master, 3 = PMP Slave, 4 = PMP Masterrw Enumeration .1.3.6.1.4.1.10728.2.16.2.2.6 |
an50WrlsVersionSets the version of the AN50 system software. The software
can be remotely downloaded into the AN50. The system
comprises sufficient memory to hold two independent software loads.
The operator can specify which load to set as the active version.rw Enumeration .1.3.6.1.4.1.10728.2.16.2.2.7 |
an50WrlsEncryptCodeThe object contains the Encryption Key used for the
AN-50 terminal. Enter the MAC address of the remote
terminal to enable over-the-air data encryption.rw OCTET STRING .1.3.6.1.4.1.10728.2.16.2.2.8 |
an50WrlsCableAttenuationThis object contains the Cable Attenuation for the AN-50 in dB.ro INTEGER .1.3.6.1.4.1.10728.2.16.2.2.9 |
an50WrlsRfPortStatusThe object specifies the status of the AN50s Wireless Port.ro Enumeration .1.3.6.1.4.1.10728.2.16.2.2.10 |
an50WrlsSaveConfigThe object saves the entire config set of the AN50.rw Enumeration .1.3.6.1.4.1.10728.2.16.2.2.11 |
an50WrlsActivateConfigThe object activates the entire config set of the AN50.rw Enumeration .1.3.6.1.4.1.10728.2.16.2.2.12 |
an50WrlsRadioEnableThe object specifies whether radio transmission is enabled or disabled.rw Enumeration .1.3.6.1.4.1.10728.2.16.2.2.13 |
an50WrlsRfStatusErrorCodeThe object specifies the Error Code for the RF Status.ro INTEGER .1.3.6.1.4.1.10728.2.16.2.2.14 |
an50WrlsRfSignalThe object specifies the Wireless Signal LED status.ro Enumeration .1.3.6.1.4.1.10728.2.16.2.2.15 |
an50WrlsLLModeLink length set mode.rw Enumeration .1.3.6.1.4.1.10728.2.16.2.2.16 |
an50WrlsLMUThis object specifies the Link measurements unit (mile / Km).rw Enumeration .1.3.6.1.4.1.10728.2.16.2.2.17 |
an50WrlsLLThis object specifies the Link Length.
See an50WrlsLMU object for units.rw INTEGER .1.3.6.1.4.1.10728.2.16.2.2.18 |
an50ConfigScheduler OBJECT IDENTIFIER .1.3.6.1.4.1.10728.2.16.2.2.19 |
an50WrlsFrameSizeThis object specifies the size of wireless frame (DL+RTD+UL)
in micro seconds.rw INTEGER .1.3.6.1.4.1.10728.2.16.2.2.19.1 |
an50WrlsMinBlockSizeThis object specifies a minimum number of bytes comprising
transmitted block.rw INTEGER .1.3.6.1.4.1.10728.2.16.2.2.19.2 |
an50WrlsDownlinkSizeThis object specifies the size of downlink sub-frame in micro seconds.rw INTEGER .1.3.6.1.4.1.10728.2.16.2.2.19.3 |
an50WrlsRoundTripDelayThis object specifies the round trip delay in micro seconds.rw INTEGER .1.3.6.1.4.1.10728.2.16.2.2.19.4 |
an50WrlsAdaptiveDLSizeThis object specifies if adaptive downlink size is
enabled or disabled.rw Enumeration .1.3.6.1.4.1.10728.2.16.2.2.19.5 |
an50WrlsExtSyncronizeThis object specifies if external synchronization is
enabled or disabled.rw Enumeration .1.3.6.1.4.1.10728.2.16.2.2.19.6 |
an50WrlsMaximumDistanceThis object specifies the maximum distance between
base station and subscriber station in Km.rw INTEGER .1.3.6.1.4.1.10728.2.16.2.2.19.7 |
an50WrlsRegistrationPeriodThis object specifies the number of frames between registration periods.rw INTEGER .1.3.6.1.4.1.10728.2.16.2.2.19.8 |
an50ConfigDefGroup OBJECT IDENTIFIER .1.3.6.1.4.1.10728.2.16.2.2.20 |
an50WrlsBroadcastDLCIRThis object specifies the broadcast downlink commited rate in kb/s.rw INTEGER .1.3.6.1.4.1.10728.2.16.2.2.20.1 |
an50WrlsBroadcastDLPIRThis object specifies the broadcast downlink peak rate in kb/s.rw INTEGER .1.3.6.1.4.1.10728.2.16.2.2.20.2 |
an50WrlsDFSActionThis object specifies the action taken when another system
is detected on the same frequencyrw Enumeration .1.3.6.1.4.1.10728.2.16.2.2.21 |
an50WrlsAntennaGainAntenna Gain in dB.rw INTEGER .1.3.6.1.4.1.10728.2.16.2.2.22 |
an50WrlsATPEnabledThis object specifies if the Automatic Transmitted Power Control
is enabledrw Enumeration .1.3.6.1.4.1.10728.2.16.2.2.23 |
an50Sw OBJECT IDENTIFIER .1.3.6.1.4.1.10728.2.16.2.3 |
an50SwServerThe address of the TFTP server used for software upgrades.
If the address of the TFTP server is unknown, return 0.0.0.0.rw IpAddress .1.3.6.1.4.1.10728.2.16.2.3.1 |
an50SwFilenameThe file name of the software image to be loaded into this device.rw OCTET STRING .1.3.6.1.4.1.10728.2.16.2.3.2 |
an50SwAdminStatusIf set to upgrade(2), the device will initiate a
TFTP software image download using an50SwFilename.
If the download process is interrupted by a reset or
power failure, the device will load the previous image.
If set to noUpgrade(1), the device will revert to the
previous version of the software.
At initial startup, this object has the default value of
noUpgrade(1).rw Enumeration .1.3.6.1.4.1.10728.2.16.2.3.3 |
an50SwOperStatusThis object shows the download status.
inProgress(1) indicates that a TFTP download is underway
completeSuccess(2) indicates that the last software upgrade
was successful
failed(3) indicates that the last attempted download
failed, ordinarily due to TFTP timeout.ro Enumeration .1.3.6.1.4.1.10728.2.16.2.3.4 |
an50SwCurrentVersThe software version currently operating in this device's flash.
This object should be in the syntax used by the individual
vendor to identify software versions. If it is not applicable,
this MUST contain an empty string.ro OCTET STRING .1.3.6.1.4.1.10728.2.16.2.3.5 |
an50SwOtherVersThe software version in the secondary flash.
This object should be in the syntax used by the individual
vendor to identify software versions. If it is not
applicable, this MUST contain an empty string.ro OCTET STRING .1.3.6.1.4.1.10728.2.16.2.3.6 |
an50Pm OBJECT IDENTIFIER .1.3.6.1.4.1.10728.2.16.3 |
an50ResetStatisticsA value of reset(2) resets the performance statistics on
the AN-50, a value of donothing(1) does nothing.rw Enumeration .1.3.6.1.4.1.10728.2.16.3.1 |
an50PmEther OBJECT IDENTIFIER .1.3.6.1.4.1.10728.2.16.3.2 |
an50PmEtherRxPacketsThis object counts the number of ethernet packets
successfully received by the local system.ro Counter .1.3.6.1.4.1.10728.2.16.3.2.1 |
an50PmEtherRxPacketsErrThis object counts the number of ethernet packet errors
received by the local system.ro Counter .1.3.6.1.4.1.10728.2.16.3.2.2 |
an50PmEtherTxPacketsThis object counts the number of Ethernet packets
transmitted by the local system.ro Counter .1.3.6.1.4.1.10728.2.16.3.2.3 |
an50PmEtherTxPacketsErrThis object counts the number of Ethernet error packets
transmitted by the local system.ro Counter .1.3.6.1.4.1.10728.2.16.3.2.4 |
an50PmEtherRxPacketsDiscThis object counts the number of ethernet packets discarded
by receiver.ro Counter .1.3.6.1.4.1.10728.2.16.3.2.5 |
an50PmEtherTxPacketsDiscThis object counts the number of ethernet packets discarded
by transmitter.ro Counter .1.3.6.1.4.1.10728.2.16.3.2.6 |
an50PmWrls OBJECT IDENTIFIER .1.3.6.1.4.1.10728.2.16.3.3 |
an50PmWrlsRxSigMinThis object indicates the minimum received signal strength
measured since the last SNMP update.ro INTEGER .1.3.6.1.4.1.10728.2.16.3.3.1 |
an50PmWrlsRxSigMeanThis object indicates the average received signal strength
measured since the last SNMP update.ro INTEGER .1.3.6.1.4.1.10728.2.16.3.3.2 |
an50PmWrlsRxSigMaxThis object indicates the maximum received signal strength
measured since the last SNMP updatero INTEGER .1.3.6.1.4.1.10728.2.16.3.3.3 |
an50PmWrlsAvgSinAdrThis object indicates the average signal to noise ratio measured
since the last SNMP update. The ratio is based on the
digital information provided from the output of the AtoD converter.ro INTEGER .1.3.6.1.4.1.10728.2.16.3.3.4 |
an50PmWrlsRxPacketsThis object indicates the number of packets received
over the air from the remote terminal.ro Counter .1.3.6.1.4.1.10728.2.16.3.3.5 |
an50PmWrlsRxPacketsRetxThis object indicates the number of packets retransmitted
over the air from the remoter terminal.ro Counter .1.3.6.1.4.1.10728.2.16.3.3.6 |
an50PmWrlsRxPacketsDiscThis object indicates the number of packets, originating from
the remote terminal lost over the air due to degradation in the RF link.ro Counter .1.3.6.1.4.1.10728.2.16.3.3.7 |
an50PmWrlsTxPacketsThis object indicates the number of wireless packets
(including Ethernet frames and error correction bytes)
transmitted over the air by the local terminal.ro Counter .1.3.6.1.4.1.10728.2.16.3.3.8 |
an50PmWrlsTxPacketsRetxThis object indicates the number of packets retransmitted
over the air by the local terminal. The retransmission scheme
is based on the Acknowledge/Request (ARQ) algorithm that detects
when packets are lost and makes a request to the MAC scheduler
to repeat transmission of the lost packets.ro Counter .1.3.6.1.4.1.10728.2.16.3.3.9 |
an50PmWrlsTxPacketsDiscThis object indicates the total number of packets lost
over the air due to degradation in the RF link.ro Counter .1.3.6.1.4.1.10728.2.16.3.3.10 |
an50PmWrlsCalcDstThis object contains the calculated link distance.ro INTEGER .1.3.6.1.4.1.10728.2.16.3.3.11 |
an50Trap OBJECT IDENTIFIER .1.3.6.1.4.1.10728.2.16.4 |
an50SysLastTrapTimeThe value of system.sysUpTime when the last trap was generated. If no traps
have been generated since the last reset, this attribute has a value of 0.
No trap is issued as a result of a change to this value.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.10728.2.16.4.1 |
an50LinkPmp OBJECT IDENTIFIER .1.3.6.1.4.1.10728.2.16.5 |
an50MaxCidThe object contains the maximum number of CID for this equipmentro INTEGER (1 .. 1024) .1.3.6.1.4.1.10728.2.16.5.1 |
an50LinkCurrentAvailIdThe current available ID in the Links table that is queried by NMS before creating a new row in Link Tablero INTEGER .1.3.6.1.4.1.10728.2.16.5.2 |